Full-HD module with LVDS interface

features a fast response time of 5 ms, very wide

viewing cone, brightness of 300 nits,

and 1000:1 contrast ratio.

LQ215M1LGN2 LCD Module

Product Specification January 2010

LCD Specification

LCD Group

Technical Document

RECORDS OF REVISION LQ215M1LGN2

SPEC No. DATE REVISED SUMMARY NOTE

No. PAGE

LD-22112 Jan. 29. 2010 1st Issue

LD-22112-1

1. Application

This specification applies to the color 21.5 Full HD TFT-LCD module, LQ215M1LGN2.

◎This specification are the proprietary product of SHARP CORPORATION(”SHARP) and include materials

protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form

or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written

permission of SHARP.

◎The device listed in this technical literature was designed and manufactured for use in OA equipment.

◎In case of using the device for applications such as control and safety equipment for transportation(aircraft,

trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require

higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and

redundant system design should be taken.

◎Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,

telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment

for life support.

◎SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply

with the instructions and the precautions specified in these specification sheets.

◎Contact and consult with a SHARP sales representative for any questions about this device.

2. Overview

This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).

It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a back light unit.

Graphics and texts can be displayed on a 1920×RGB×1080 dots panel with about 16.7 million colors by using

LVDS (Low Voltage Differential Signaling) and supplying +5.0V DC supply voltages for TFT-LCD panel

driving and supply voltage for backlight.

LD-22112-2 3. Mechanical Specifications

Parameter Specifications Unit

Display size 54.68 (Diagonal) cm

21.53 (Diagonal) Inch

Active area 476.64 (H)×268.11 (V) mm

Pixel format 1920 (H)×1080 (V) Pixel

(1 pixel＝R+G+B dots)

Pixel pitch 0.24825(H)×0.24825 (V) mm

Pixel configuration R, G, B vertical stripe

Display mode Normally white

Unit outline dimensions *1 495.6(W)×292.2(H)×9.8(D) (TYP) mm

Mass 1600 (MAX) g

Surface treatment Anti-glare and hard-coating 3H

(Haze value = 25)

*1.Note: excluding back light cables, cover and pet sheets.

The thickness of module (D) doesn’t contain the projection.

Outline dimensions are shown in Fig.7

LD-22112-3 4. Input Terminals

4-1. TFT-LCD panel driving CN1 (Interface signals and +5.0V DC power supply)

Using connectors ：GS23302-0011R-7F(FOXCONN) Corresponding connectors ：FI-XB30SRL-HF11(JAE) (Sharp is not responsible to its product quality, if the user applies a connector not corresponding to the above

model.)

Pin No. Symbol Function Remark 1 R1IN0- Receiver signal of A side pixel (-) LVDS 2 R1IN0+ Receiver signal of A side pixel (+) LVDS 3 R1IN1- Receiver signal of A side pixel (-) LVDS 4 R1IN1+ Receiver signal of A side pixel (+) LVDS 5 R1IN2- Receiver signal of A side pixel (-) LVDS 6 R1IN2+ Receiver signal of A side pixel (+) LVDS 7 GND 8 CK1 IN- Clock signal of A side pixel (-) LVDS 9 CK1 IN+ Clock signal of A side pixel (+) LVDS

10 R1IN3- Receiver signal of A side pixel (-) LVDS 11 R1IN3+ Receiver signal of A side pixel (+) LVDS 12 R2IN0- Receiver signal of B side pixel (-) LVDS 13 R2IN0+ Receiver signal of B side pixel (+) LVDS 14 GND 15 R2IN1- Receiver signal of B side pixel (-) LVDS 16 R2IN1+ Receiver signal of B side pixel (+) LVDS 17 GND 18 R2IN2- Receiver signal of B side pixel (-) LVDS 19 R2IN2+ Receiver signal of B side pixel (+) LVDS 20 CK2 IN- Clock signal of B side pixel (-) LVDS 21 CK2 IN+ Clock signal of B side pixel (+) LVDS 22 R2IN3- Receiver signal of B side pixel (-) LVDS 23 R2IN3+ Receiver signal of B side pixel (+) LVDS 24 GND 25 NC 【Note1】 26 NC 【Note1】 27 NC 【Note1】 28 Vcc +5.0V Power supply 29 Vcc +5.0V Power supply 30 Vcc +5.0V Power supply

[Note 1] Not connection, this pin should be open.

LD-22112-4 4-2 LVDS Data Mapping

DE : Display Enable NA : Not Available

CK1IN+/-

R14’ R13’ R12’ R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”R1IN0+/-

G15’ G14’ G13’ G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B11”R1IN1+/-

NA B15’ B14’ B13’ B12’ DE NA NA B15 B14 B13 B12 DE” R1IN2+/-

CK2IN+/-

R2IN0+/-

G25’ G24’ G23’ G22’ G21’ B21 B20 G25 G24 G23 G22 G21 B21”R2IN1+/-

NA B25’ B24’ B23’ B22’ NA NA NA B25 B24 B23 B22 NA R2IN2+/-

Previous Cycle Current Cycle

R24’ R23’ R22’ R21’ R20’ G20 R25 R24 R23 R22 R21 R20 G20”

B16’ G17’ G16’ R17’ R16’ NA B17 B16 G17 G16 R17 R16 NA R1IN3+/-

B26’ G27’ G26’ R27’ R26’ NA B27 B26 G27 G26 R27 R26 NA R2IN3+/-

LD-22112-5 4-3 Backlight

CN2, 3 (Upper/Lower FPC Connector Pin Assignment)

Using connector ：7080-Q10N-00R (Entery INDUSTRIAL CO.,LTD)

Corresponding FFC specification ：Temperature＝80oC, Voltage=60V, Pin No.=10, 0.5Pitch, PET, HF

CN2 and CN3 are the same pin assignment. Pin No Symbol Description

1 IRLED1 IRLED1 LED current sense for string 1 2 IRLED1 IRLED1 LED current sense for string 1 3 IRLED2 IRLED1 LED current sense for string 2 4 VLED LED power supply 5 VLED LED power supply 6 VLED LED power supply 7 VLED LED power supply 8 IRLED2 IRLED1 LED current sense for string 2 9 IRLED3 IRLED1 LED current sense for string 3

10 IRLED3 IRLED1 LED current sense for string 3

5. Absolute Maximum Ratings

Parameter Symbol Condition Ratings Unit Remark

Supply voltage Vcc Ta=25℃ －0.3 ～ + 6.0 Ｖ

Input voltage VI Ta=25℃ －0.3 ～ + 4.3 V

Storage temperature TSTG － －20 ～ + 60 ℃ 【Note1】

Operating temperature (Ambient) TOPA － 0 ～ + 50 ℃ 【Note2】 【Note1】The relative humidity must not exceed 90% non-condensing at temperatures of 40°C or less. At temperatures greater than 40°C, the wet bulb temperature must not exceed 39°C.

【Note2】The unit should not be exposed to corrosive chemicals.

CN2

CN3

LD-22112-6 6. Electrical Characteristics

6-1. TFT-LCD panel driving Ta＝25℃ Parameter Symbol Min. Typ. Max. Unit Remark

Supply voltage Vcc +4.5 +5.0 +5.5 V 【Note2】 Current dissipation Black Icc － 1000 1300 mA 【Note3】 White Icc － 700 1000 mA 【Note4】 Mosaic Icc – 900 1200 mA 【Note5】 Permissive input ripple voltage VRF － － 150 mVp-p Differential input High VTH － － +100 mV VCM=+1.2V threshold voltage Low VTL –100 － － mV 【Note1】 Terminal resistor RT － 100 － Ω Differential input

【Note1】 VCM : Common mode voltage of LVDS driver.

【Note2】

1）On-off conditions for supply voltage

Symbol Min. Max. Unit Remark t1 0.1 10 ms t2 0 50 ms t3 0 50 ms t4 0.1 50ms ms t5 1000 － ms t6 200 － ms *1 t7 100 － ms *1

*1 : Power sequence for Backlight is not especially specified, however it is recommended to consider some timing difference between LVDS input and Backlight input as shown above. If the Backlight lights on before LCD starting, or if the Backlight is kept on after LCD stopping, the screen may look white for a moment or abnormal image may be displayed. This is caused by variation in output signal from timing generator at LVDS input on or off. It does not cause the damage to the LCD module.

t1 t2

t6

0.9Vcc0.9Vcc

Vcc

Valid

Backlight

Signal (LVDS Interface)

0.1Vcc 0.1Vcc 0.1Vcc

t3 t5

OFF OFF

Backlight ON (LED)

t7

t4

90% 90%

LD-22112-7 【Note3】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition

whereas black pattern is displayed.

【Note4】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition

whereas white pattern is displayed.

【Note5】The specified current is under the Vcc =5V, 25 °C, fv=60Hz (frame frequency) condition

whereas mosaic pattern(black & white [8*6] ) is displayed. White : GS255

Black : GS0

6-2. Backlight driving The backlight system is edge-lighting type with 198 White-LED(White Light Emitting Diode, (11 serial x 3 parallel) x 3 strings x 2 (Upper/Lower) ). The characteristics of White-LED are shown in the following table. (Ta = 25℃)

Parameter Symbol Min. Typ. Max. Unit Remark Supply voltage range VLED － 36.3 37.4 V Duty 100% Current dissipation ILED － 360 396 mA 【Note1,2,3】 Power Consumption PLED － 13.07 14.81 W 【Note4】 LED Life time LBL 25,000 30,000 － Hour 【Note5】

【Note1】There are two Light Bars, and the specified current is input LED chip 100% duty current.

【Note2】The sensing current of each string is 60mA.

【Note3】Each light bar have three current sensing strings, so that each light bar input current is 180mA.

【Note4】PLED = ILED × VLED , LED matrix is (11S3P) x 3 strings x 2.

【Note5】The life time is determined as the time at which luminance of the LED becomes 50% of the initial brightness or not normal lighting at ILED=360mA on condition of continuous operating at 25±2°C.

【Note6】In case of using PWM control for blacklight driving, please keep frequency enough high in order to avoid the flicker or the deterioration of display quality.

LD-22112-8 7. Timing characteristics of input signals

7-1. Timing characteristics

Parameter Symbol Min. Typ. Max. Unit

Clock signal Frequency 1/Tc 60 72 87.5 MHz

Horizontal period TH 1000 1088 1120 Clock Horizontal

Horizontal period(High) THd 960 960 960 Clock

Vertical period TV 1090 1100 1160 Line

Vertical period(High) TVd 1080 1080 1080 Line

Vertical

frequency Fv 50 60 75 Hz

【Note】 In case of using the long vertical period, the deterioration of display quality, flicker etc. may occur.

1 3 1919

THd

TH

TVd

TV

Tc

1 2 1080 1079

1919

2 4 1920 1920

A side (R1,G1,B1) B side (R2,G2,B2)

DE

DE

LD-22112-9 7-2 Input Data Signals and Display Position on the screen

１・１ １・２ １・３

２・１ ２・２

３・１

1080･1

1･1920

1080･1920

R1 G1 B1 R2 G2 B2 (１､１) (１,２)

Display Position of Data (V,H)

R G B

Two pixels-data are sampled at the same time.

＊A side ： R10～R15, G10～G15, B10～B15

＊B side ： R20～R25, G20～G25, B20～B25

LD-22112-10 8. Input Signals, Basic Display Colors and Gray Scale of Each Color

8-1 8bit input

Data signal

Colors & Gray

Gray scale Scale R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7

Black － 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Blue － 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Green － 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Cyan － 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Red － 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Magenta － 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

Yellow － 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

White － 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Brighter GS253 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GS254 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Red GS255 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GS1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Darker GS2 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Brighter GS253 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0

GS254 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Green GS255 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0

Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

GS1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0

Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0

Brighter GS253 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1

GS254 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1

Blue GS255 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1

0 : Low level voltage, 1 : High level voltage.

Each basic color can be displayed in 255 gray scales from 8 bit data signals. According to the combination of

total 24 bit data signals, the 16.7-million-color display can be achieved on the screen.

Basic C

olor G

ray Scale of Red

Gray Scale of G

reen G

ray Scale of Blue

LD-22112-11 9. Optical Characteristics

Parameter Symbol Condition Min. Typ. Max. Unit Remark

θ11 70 80 － Deg. Vertical

θ12 70 80 － Deg.

Viewing

angle

range Horizontal θ21,θ22

CR≧10

75 85 － Deg.

【Note3,5,6】

Contrast ratio ＣＲ θ=0° 700 1000 － 【Note3,7】

Response Rise τｒ － 1.5 3 ms 【Note4】

Time Fall τd － 3.5 7 ms

Rise+Fall τr +τd － 5 10 ms

x 0.283 0.313 0.343 【Note3】 Chromaticity of

White y 0.299 0.329 0.359

x 0.610 0.640 0.670 Chromaticity of

Red y 0.315 0.345 0.375

x 0.294 0.324 0.354 Chromaticity of

Green y 0.589 0.619 0.649

x 0.120 0.150 0.180 Chromaticity of

Blue y 0.029 0.059 0.089

Luminance of white YL

250 300 － cd/m2 【Note3】

White Uniformity δw1

θ=0°

0.70 0.75 － － 【Note3,8】

Cross Talk Dsha θ=0° － － 2 % 【Note9】

【Note1】Ambient temperature = 25°C. 【Note2】To be measured in dark room after backlight warm up 30 minutes. 【Note3】To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A. 【Note4】 Definition of response time:

The output signals of BM-7 are measured when the input signals are changed from “Black” to

“White” (falling time) and from “White” to “Black” (rising time), respectively. The response time

interval is between the 10% and 90% of amplitudes. Refer to figure as below.

τr τd

0% 10%

90% 100%

White whiteblack

time

Phot

odet

ecto

r Out

put

(Rel

ativ

e V

alue

)

LD-22112-12

【Note5】Optical Characteristics Measurements:

【Note6】Definitions of viewing angle range:

【Note7】Definition of contrast ratio:

The contrast ratio is defined as the following.

Contrast Ratio(CR) = Luminance(brightness)with all pixels whiteLuminance(brightness)with all pixels black

【Note8】Definition of white uniformity:

White uniformity is defined as the following with nine measurements (1～9).

σw1 = Minimum Brightness of nine points(P1～P9). Maximum Brightness of nine points(P1～P9).

W/10

W/2

9W/10

W

D/10 D/2 9D/10D

2 1 3

5 4 6

8 7 9

Normal line

θ21 θ11

θ12 θ22

6 o’clock direction

Center of screen(θ=0°)

TFT-LCD-Module

500mm

Field=2°

BM-5A (TOPCON)

LD-22112-13

【Note9】Definition of cross talk:

We measured luminance in case there are a window frame and in case there are not a window frame with A points

& B points of the following figure. Then, we compared the measured values.

Dsha(%) = |Luminance with a window frame - Luminance without a window| Luminance without a window ×100

0 gray level

1/2

1/2

1/6

1/6A

B

1/2 1/6

1/6

2/3 1/3

A’

B’

127 gray level 127 gray level

1/3

1/2

2/3

LD-22112-14

10. Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. b) Be sure to design the cabinet so that the module can be installed without any extra stress such as

warp or twist. c) Since the front polarizer is easily damaged, pay attention not to scratch it.

Blow away dust on the polarizer with antistatic N2 blow. It is undesirable to wipe off because a polarizer is sensitive. It is recommended to peel off softly using the adhesive tape when soil or finger oil is stuck to the polarizer. When unavoidable, wipe off carefully with a cloth for wiping lenses.

d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

Handle with care. g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth

when handling.Observe all other precautionary requirements in handling components. h) Since there is a circuit board in the module back, stress is not added at the time of a design assembly.

Please make it like. If stress is added, there is a possibility that circuit parts may be damaged. i) Protection film is attached to the module surface to prevent it from being scratched .

Peel the film off slowly , just before the use, with strict attention to electrostatic charges. Blow off 'dust' on the polarizer by using an ionized nitrogen.

j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which degrades display quality.

k) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such environment.

l) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise. m) When handling LCD modules and assembling them into cabinets, please avoid that long-term storage in

the environment of oxidization or deoxidization gas and the use of such materials as reagent,solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules.

o) When install LCD modules in the cabinet, please tighten with “torque=3.0kgf･cm (Max)”. Be sure to confirm it in the same condition as it is installed in your instrument.

p) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if itgets inside your eye or mouth by mistake.

q) Notice : Never dismantle the module , because it will cause failure. Please don't remove the fixed tape, insulateing tape etc that was pasted on the original module. (except for protection film of the panel and the crepe tape(yellow tape) of fixing lamp cable temporarily.)

r) Be careful when using it for long time with fixed pattern display as it may cause afterimage. (Please use a screen saver etc., in order to avoid an afterimage.)

s) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied.

t) If a minute particle enters in the module and adheres to an optical material, it may cause display non-uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.

LD-22112-15 11. Packing form

a) Piling number of cartons : maximum 2 cartons

b) Packing quantity in one carton : 8 modules

c) Carton size : 565mm(W)×250mm(D)×420mm(H)

d) Total mass of one carton filled with full modules : 14.5kg(Max.)

e) Packing form is shown in Fig.1,2,3

Fig 1 Fig 2 Fig 3

Step 1 Take a carton and put bottom pad 1pcs as fig1. Step 2 Place the module with PCBA under then put it falls horizontally into the carton all 8pcs as fig2.

Step 3 Cover them with 1pcs top pad then to seal discount as fig3.

Bottm Pad

Top Pad

LD-22112-16

12. Shipping Pallet Package

a) Total mass of two pallets filled with full modules : 505kg(Max.)

Step 1 Place a pallet specially, spec is:1130mm*1100mm*140mm,as fig4.

Step 2 Stack cartons on the Pallet in 2 tiers,8 cartons in a tier, total 16 cartons.

Then place Corner paper and Upper Cover, as fig5.

Step 3 Pile of cargo according to 2 tiers pallets. Notes: top pallet and bottom pallet need to pile up neat and tidy as fig6.

Fig 4 Fig 5 Fig 6

Corner paper×4

Cover×1

Pallet×1

Pallet

Carton×16

LD-22112-17

13．Reliability test items No Test item Conditions Judgment Remark1 High temperature storage test 60℃, 240h Note 1 Note 2 2 Low temperature storage test -20℃, 240h Note 1 Note 2 3 High temperature

& high humidity operation test 40℃, 90%RH, 240h (No condensation)

Note 1 Note 2

4 High temperature operation test 50℃, 240h Note 1 Note 2 5 Low temperature operation test 0℃, 240h Note 1 Note 2 6 Vibration test

(non- operating) Vibration level : 1.5G Bandwidth : 10-300Hz Waveform : sine wave, Sweep rate : 10min 30 min for each direction X, Y, Z (1.5 Hrs in total)

Note 1 Note 2

7 Shock test (non- operating)

Shock level : 50G, 11ms Waveform : Half sine wave Direction : ±X, ±Y, ±Z One time each direction

Note 1 Note 2

8 Thermal shock test (Storage)

-20℃～60℃ 1Hr, 1Hr, 100cycles

Note 1 Note 2

9 ESD test

Contack : +/-8kV, 150pF(330ohm) 10times/1point, time/1 sec, total 16 points Air discharge : +/-15kV, 150pF(330phm) 10times/1point, 1time/1 sec, total 9 points

Note 1 Note 2

10 MTBF Demonstration 25,000 hours with confidence level 90% Note 1 Note 3

【Note 1】Pass: Normal display image with no obvious non-uniformity and no line defect.

Partial transformation of the module parts should be ignored.

Fail: No display image, obvious non-uniformity, or line defects. 【Note 2】Evaluation should be tested after storage at room temperature for two hour.

【Note 3】The MTBF calculation is based on the assumption that the failure rate distribution meets the

Exponential Model, and B/L is not included.

LD-22112-18 14．Others

1) Lot No. and indication Bar Code Label:

Serial No.

Z1 Z2 Z3 Z4 Z5 Z 6 Z 7 Z8 Z9 Z10

Serial ID includes the information as below:

1. Year: Final digit of the A.D. EX.”0” for 2010 2. Month: 1~9, X, Y, and Z. (X=Oct. Y=Nov. Z=Dec.) 3. Day: 1～9,A to X.(please refer Day Code table) 4. Sharp internal use 5. Serial No: 0~99999, Over 10Kpcs use A, B, C… For example: Actual Print 99,999 99999 100,000~ A0000~ 110,000~ B0000~ 120,000~ C0000~ 6. Revision code: The first Version is A, version changes with design change. Version with 26 letters, For example: A, B, C…

Day Code table Date Day Code Date Day Code Date Day Code

1 1 11 B 21 M2 2 12 C 22 N3 3 13 D 23 P4 4 14 E 24 Q5 5 15 F 25 R6 6 16 G 26 S7 7 17 H 27 T8 8 18 J 28 U9 9 19 K 29 V10 A 20 L 30 W

31 X

20 mm

45 mm

SHARP LQ215M1LGN2

Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9 Z10

Revision code

Month

Year

Sharp Internal use

Serial No

Day

LD-22112-19

2) Packing Label

① Model No. (LQ215M1LGN2)

② Lot No. (Date)

③ Quantity

3) If any problem occurs in relation to the description of this specification , it shall be resolved through

discussion with spirit of cooperation.

社内品番：（４Ｓ）LQ215M1LGN2

ＬｏｔＮＯ． ：（１Ｔ）２０１０．Ｘ．ＸＸ

Ｑｕａｎｔｉｔｙ：（Ｑ） ８ ｐｃｓ

ユーザ品番 ：

Bar code（①）

Bar code（②）

Bar code（③）

シャープ物流用ラベルです。

LD-22112-20

Fig7.LQ215M1LGN2 OUTLINE DIMENSIONS

NORTH AMERICA

Sharp Microelectronics of the Americas

5700 NW Pacific Rim Blvd.

Camas, WA 98607, U.S.A.

Phone: (1) 360-834-8700

Fax: (1) 360-834-8903

www.sharpsma.com

TAIWAN

Sharp Electronic Components

(Taiwan) Corporation

8F-A, No. 16, Sec. 4, Nanking E. Rd.

Taipei, Taiwan, Republic of China

Phone: (886) 2-2577-7341

Fax: (886) 2-2577-7326/2-2577-7328

CHINA

Sharp Microelectronics of China

(Shanghai) Co., Ltd.

28 Xin Jin Qiao Road King Tower 16F

Pudong Shanghai, 201206 P.R. China

Phone: (86) 21-5854-7710/21-5834-6056

Fax: (86) 21-5854-4340/21-5834-6057

Head Office:

No. 360, Bashen Road,

Xin Development Bldg. 22

Waigaoqiao Free Trade Zone Shanghai

200131 P.R. China

Email: smc@china.global.sharp.co.jp

EUROPE

Sharp Microelectronics Europe

Division of Sharp Electronics (Europe) GmbH

Sonninstrasse 3

20097 Hamburg, Germany

Phone: 49 (0)180 507 35 07

Fax: (49) 40-2376-2232

www.sharpsme.com

SINGAPORE

Sharp Electronics (Singapore) PTE., Ltd.

438A, Alexandra Road, #05-01/02

Alexandra Technopark,

Singapore 119967

Phone: (65) 271-3566

Fax: (65) 271-3855

KOREA

Sharp Electronic Components

(Korea) Corporation

RM 501 Geosung B/D, 541

Dohwa-dong, Mapo-ku

Seoul 121-701, Korea

Phone: (82) 2-711-5813 ~ 8

Fax: (82) 2-711-5819

JAPAN

Sharp Corporation

Electronic Components & Devices

22-22 Nagaike-cho, Abeno-Ku

Osaka 545-8522, Japan

Phone: (81) 6-6621-1221

Fax: (81) 6117-725300/6117-725301

www.sharp-world.com

HONG KONG

Sharp-Roxy (Hong Kong) Ltd.

Level 26, Tower 1, Kowloon Commerce Centre,

No. 51, Kwai Cheong Road, Kwai Chung,

New Territories, Hong Kong

Phone: (852) 28229311

Fax: (852) 28660779

www.sharp.com.hk

Shenzhen Representative Office:

Room 602-603, 6/F.,

International Chamber of Commerce Tower,

168 Fuhua Rd. 3, CBD,

Futian District, Shenzhen 518048,

Guangdong, P.R. China

Phone: (86) 755-88313505

Fax: (86) 755-88313515

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Suggested applications (if any) are for standard use; See Important Restrictions for

limitations on special applications. See Limited Warranty for SHARP’s product warranty.

The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF

MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE,

ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in

any way, for any incidental or consequential economic or property damage.

LCD Group

LCD Specification

Technical Document

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information: Sharp Microelectronics:

  LQ215M1LGN2