childrens design safety guide 5.12
TRANSCRIPT
-
8/6/2019 Childrens Design Safety Guide 5.12
1/18
Target Childrens Apparel
Design Safety Guide
Published March, 2010
Table of Contents
Cords Pages 2-7
Small Parts & Sharp Points/Edges Pages 7-15
Knit Products Page 16
Genuine Kids (additional requirements) Page 17
Change Log Page 18
Toys Refer to Hardgoods requirements
TM
NOTE: Changes to content are identified with bold, blue text.
http://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmphttp://wiki.target.com/tgtwiki/index.php/File:Bullseye.bmp -
8/6/2019 Childrens Design Safety Guide 5.12
2/18
Safety Concern: Potential safety concern if cord is caught in playgroundequipment, a bus door, fences, tree branches, etc..
Defined as: a textile or non-textile material braided, twisted, fused or
woven together. Including but not limited to a sash, drawstring, tie or belt
which can be permanently attached to the garment or
independent/removable from the garment
Cords include but are not limited to;
drawstrings, belts, ties, sashes, and bungee cords.
Cords Design Safety Guide - Definitions
Belt: Exposed and
removable from the
garment
Tie: Exposed and
permanently attached
to the garment
Drawstring: Encased
in a channel within
the garment
CORD TYPES
FUNCTIONAL: Alters the shape or size of the garment
(adjustable).
NON-FUNCTIONAL:
(decorative)
Secured to the garment in a way not to allow the
size or shape of the garment to be altered.
Purpose is to provide a decorative element to thegarment ONLY.
-
8/6/2019 Childrens Design Safety Guide 5.12
3/18
Cords Design Safety Guide
Component Example Category Sizes 0-5T Sizes 4-16
rawstrings
ead & Neck
rea
Functional /
Non-Functional
NOT Allowed
rawstrings
Waist & Hip Area
Functional Allowed
Must be tacked at CB & cannot exceed 3
exposed when garment is fully extended
Non-Functional Allowed
Must be tacked to garment and cannoexceed 3 past tack point.
rawstrings &ies
nkle Area, Leg
Opening
Functional /
Non-Functional
NOT Allowed
ies
ead, Neck,
houlder or
leeve Area
Functional NOT Allowed
Non-Functional Allowed
Pre-tied & tacked to garment, tailcannot exceed 3 from tack point.
Cannot appear to be a faux draw cord
ies-Lacingead & Neck
rea
Functional /
Non-Functional
NOT Allowed
No knots or attachments allowed at the free ends of Drawstrings or Ties.
-
8/6/2019 Childrens Design Safety Guide 5.12
4/18
Component Example Category Sizes 0-5T Sizes 4-16
Ties on Hats(Chin Straps)
Head & NeckArea
Functional /
Non-Functional
Allowed
Not allowed on crown of hat.Single Strap may not exceed 8
from tack point.
Two straps (one, each side) may notexceed 5 each from tack point.
Ties
Halter Style
Functional NOT Allowed Allowed
Non-Functional Allowed
Straps must join with
non-adjustable
closure or be one
continuous strap
RemovableBelt or Sash
Waist and Hip
Area
Always
Functional
NOT Allowed Allowed
TiesWaist fromSide Seam
(Dresses and
Tops, Non-
Outerwear)
Functional NOT Allowed
Allowed
Each tie length cannot
exceed: XS:18 /
SM:19 / M:20 /
LG:21.5 / XL:23
Non-Functional NOT Allowed
Ties
Waist & Hip
Area
Functional NOT Allowed Allowed
Must be tacked at CB& cannot exceed 3
past belt loop or exitpoint when garment is
fully extended.
Non-Functional Allowed
Must be tacked togarment and
cannot exceed 5
past tack point .
Allowed
Must be tacked togarment and cannotexceed 5 past tack
point .
Cords Design Safety GuideNo knots or attachments allowed at the free ends of Drawstrings or Ties.
-
8/6/2019 Childrens Design Safety Guide 5.12
5/18
Component Example Category Sizes 0-5T Sizes 4-16
Ties-LacingWaist & HipArea
Functional NOT Allowed Allowed
Must be tacked at CB &cannot exceed 3
exposed when garment
is fully extended.Non-Functional Allowed
Must be tacked every 3 & at exit point.
Tie cannot exceed 3 past tack point .
Ties-CinchingWaist & Hip
Area
Functional NOT Allowed
Non-Functional Allowed
Must be tacked every 3 & at exit point.
Tie cannot exceed 3 past tack point .
Ties-Cinchingat Leg
Opening
Functional NOT Allowed
Non-Functional Allowed
Must be above ankle area.
Not allowed on full length pants.Must be tacked every 3& at exit point.
Tie cannot exceed 3 past tack point
Tab -Convertible
Leg
Functional /
Non-Functional
Allowed
Tab must be on inside of the leg & cannot
extend past leg hem when unrolled.
ElasticBungee Cord& Toggle
Waist & Hip
(Outerwear &
NonOuterwear)
Functional/
Non-Functional
NOT Allowed
Cords Design Safety GuideNo knots or attachments allowed at the free ends of Drawstrings or Ties.
-
8/6/2019 Childrens Design Safety Guide 5.12
6/18
Component Example Category Sizes 0-5T Sizes 4-16
Elastic BungeeCord Mittens orGloves
Always
FunctionalAllowed
Mitten Keeper;Tab with Snap
Always
Functional
Allowed
Tab length may notexceed 3 when unsnapped.
Tab must be placed at inner cuffand cannot extend morethan 1 past cuff edge.
Bib Overalls Functional /
Non-Functional
Allowed
Strap length appropriate for garment.
Fringe; GarmentEdges
Functional/
Non-functional
Allowed
Maximum Length 2
Fringe;EmbroideredDesigns
Functional/
Non-functional
Allowed
Maximum length 0.375
Cords Design Safety GuideNo knots or attachments allowed at the free ends of Drawstrings or Ties.
-
8/6/2019 Childrens Design Safety Guide 5.12
7/18
Safety Concern: potential injury for cuts or skin puncture by
a trim component.
Defined as: a trim component sharp to the touch, or that
activates a sharp points or edge tester.
Requirement, Sizes 0-16: All accessible trims; no sharp
points or edges allowed before and after Use and Abuse
testing.
Sharp Points and Edges
Small Parts
2.25 in
57.10mm
1.25in
31.70mm
Example of testing cylinder Safety Concern: potential choking
hazard if trim component becomes
accessible and is swallowed by a child.
Defined as: a trim component able to fit
completely into a specially designed test
cylinder (2.25 long by 1.25 wide,
shown at left). Cylinder mimics the
approximate size of the fully expanded
throat of a child.
Requirement, Sizes 0-5T; All accessible
trims must either meet Targets Use
and Abuse test requirements, or be
unable to fit into a small parts cylinder.
-
8/6/2019 Childrens Design Safety Guide 5.12
8/18
Targets Use & Abuse Testing
Garment preparation: 3 Home Launderings per care
instructions
Sizes 0-5T Torque and Tension MUST meet the requirement
on the SAME sample.
Torque- (twist)Sizes: 0-18M requirement 2.0 1bs/10sec
Sizes 24M-36M requirement 3.0lbs/10sec
Sizes 2T-5T requirement 4.0 lbs/10sec
Sizes 4-16 requirement 3.0lbs/10sec
Sizes 4-16 concealed zippers requirement 1.3lbs/10sec
Tension-(attachment/pull strength)
Sizes 0-5T requirement 17lbs/10sec
Sizes 4-16 requirement 15 lbs/10sec
Products crossing size ranges must meet the most
stringent requirements.
-
8/6/2019 Childrens Design Safety Guide 5.12
9/18
Component Example Sizes 0-5T Sizes 4-16
Accessories &Charms
NOT Allowed Allowed
Must meet all childrens
jewelry requirements
Brooches & Pins NOT Allowed NOT Allowed
Due to accessiblesharp point.
Bib Overalls Hasps& Sliders
See separate slide
or illustration
Allowed
Must be single piece and continuous
Buttons Allowed
4 Hole and 2 Hole
Must be 14L+ andattached by lockstitch
Allowed
Attached by lockstitch
Buttons; Shank NOT Allowed Allowed
Button; Toggle Allowed
Must be attached with
fabric.
Allowed
Must meet attachment
strength testing
Small Parts, Sharp Points & EdgesAll components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
10/18
Component Example Sizes 0-5T Sizes 4-16
Tack withAluminum Neck
NOT Allowed
Claw Setting NOT Allowed
Decorative Studsand Rivets
Allowed
Must be rivet attached.
Not Allowed: Adhesive, heat set, or prong
attach.
D-Rings Allowed
Must be continuous
DecorativeAttachments,Plastic Tipping,and Knots on endof Cords, Belts,Ties, etc.
NOT Allowed
Decorative Bow,Ties & Cords
Allowed
Must be pre-tied and tacked to garment.
Tail cannot exceed 3 in length.
Small Parts, Sharp Points & Edges
1
All components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
11/18
Component Example Sizes 0-5T Sizes 4-16
Fabric Accessoriesor Appliqus
i.e.; Flowers with
petals
Allowed
No FELT allowed. Attachment must meet Use & Abuserequirements for individual component (petal), and as a
whole (flower).
Fusible web interlining may only be applied to inside of
garment; may not be used on back of fabric components.
Fabric Rosettes Allowed
No FELT allowed. Attachment must meet Use & Abuse
requirements for individual component (petal), and as a
whole (flower).
Grass Skirt Allowed
Strand length from WB may not exceed the following:
10 for 12M-24M,
12 for 2T-5T.
Not allowed for 0-9M.
Each strand to be doubled over at waist
and stitched 2-3 times.
Hanger Loops,Lingerie Straps
NOT Allowed Allowed
Hook & Loopclosure
AllowedMust have rounded corners
Small Parts, Sharp Points & Edges
1
All components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
12/18
Component Example Sizes 0-5T Sizes 4-16
Locker Loops
*May NOT be used
for the purpose of
attaching a scarf,belt, etc.
Allowed
Must be horizontal,
tacked at two points.
May not exceed 1.5
Allowed
Must be horizontal,
tacked at two points.
May not exceed 2.0
Loop, Decorative
*May NOT be used
for the purpose of
attaching a scarf,
belt, etc.
Allowed
May not exceed 2.5.
Must be tacked at both
ends.
Allowed
May not exceed 3.
Must be tacked at both
ends.
Mitten Keeper Allowed
Must be two continuous pieces
Plastic Grommets& Eyelets
NOT Allowed
Metal or StitchedGrommets &Eyelets
Allowed
Pom-Poms Allowed
Cannot be attached to ends of
drawstrings, ties, or belts.
Attachment must meet Use & Abuse requirementsfor individual component (yarn or strand),
and as a whole (entire pom-pom).
Small Parts, Sharp Points & Edges
1
All components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
13/18
Component Example Sizes 0-5T Sizes 4-16
Ring Snaps Allowed
Plastic covered ring snaps (metal base) areallowed on childrens sizes 0-16.
Snaps Allowed
Rhinestones Not Allowed Allowed
Strap Sliders Allowed
Swim Hook(S-Hook)
Allowed
Must be continuous on one side
Small Parts, Sharp Points & Edges
1
All components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
14/18
Component Example Sizes 0-5T Sizes 4-16
Zippers;Concealed
NOT Allowed Allowed
To be placed at center
back, where it is not easily
accessed by wearer.
Zippers
Plastic and Metal
Allowed
Facing or binding
required to conceal back
of zipper from skin for
Newborn sizes.
Recommended for Infant
sizes.
Allowed
Zipper Pull Tab
Textile/Leather
Allowed
Must be bar tacked so
loop cannot exceed 0.75
Allowed
Zipper Pull Tab
Metal or Novelty
Allowed Allowed
Zipper SolidStops
Solid stop required for all sizes 0-16,
to ensure that slider cannot bepulled or twisted off of the zipper.
Small Parts, Sharp Points & Edges; Zippers
AcceptableNOT
Acceptable
1
All components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
15/18
Component Example Sizes 0-5T Sizes 4-16
Sequins Allowed
Sequins cannot be
accessible.
Must be covered with
mesh or equivalentmaterial.
Allowed
LaminateSequins
Laminate
Sequins / HeatSet Application
Not Allowed Allowed
1
Small Parts, Sharp Points & EdgesAll components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
16/18
Knit Products Design Safety Guide
Component Example Sizes 0-5T
Sock Sizes 0-6.5
Sizes 4-16
Sweater
Interior Float
Length
Allowed
Cannot exceed 0.75
Sweater
Open Knit
Pattern
Allowed
Must be small enough to
prevent childs finger from
passing through material.
Suggest to use with 5ggand heavier.
Allowed
Float Length
Mittens/Gloves,
Socks,
Patterned Tights& Leggings
Allowed
Cannot exceed 0.25 in
length.
Float yarns which are cutopen cannot exceed
0.375 in length.
Allowed
1
-
8/6/2019 Childrens Design Safety Guide 5.12
17/18
Genuine Kids Additional RequirementsTM
Component Example Sizes 0-24mo. Sizes 2T-5T
Buttons Allowed
Must be 4 hole and 14L.
Must be lock stitched.
D Rings NOT Allowed Allowed
Maximum diameter of 1.50
Drawstrings,Ties &Attachments;Knee Area
Functional / Non Functional
NOT Allowed
Hammer Loop AllowedHammer loop to be stitched to body
1
All components must meet Target Trim standards documented in the Target A&A Manual on POL.
-
8/6/2019 Childrens Design Safety Guide 5.12
18/18
Change Log
Date Change
3/9/10 Updated format, changes to content based on CPSC updates. Changesare identified in bold blue text.
1/15/10 Updates to tie requirements. Updated photo examples.
11/10/09 Addition of photos
9/17/09 Addition/Clarification of: locker loop, toggle buttons, appliqus, decorativestuds.