1 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

1 Set the marking head components box aside and carefully lift the FH Marking Head out of the box do not use any fittings on the sides to lift andor carry the marking head

Important

Note

See the FH Flyer Marking Head (MH) Operators Manual for complete installation details and instructions A PDF version is available online at httpwwwsynradcomManualsmanuals_laserhtm Reference your laserrsquos specific Quick Start Guide also located on our website httpwwwsynradcomsynraddocrootresourceslibrariesquickstart

Read all Danger Warning Caution terms symbols and instructions located in the (Laser Safety Hazard information) sections in the Operation Manual

FH FlyerMarking Head hardware kit

Lift both the both the marking head and the foam packaging out

of the box

ImportantNote

Keep All Foam and Packaging you will need to re-use it when moving your marking head to prevent damage that could void your warranty Refer to this guide and the Technical Reference chapters in the Operation Manual when re-packaging for ship-ping andor relocation Remove all accessory items not originally attached to the laser prior to re-packaging for shipping

Marking Head Unpacking

Note Reference your specific laser QSG amp our Mounting 101 located on our website

2 Upon arrival inspect all shipping containers for signs of damage If you discover shipping damage document the damage (photographically if possible) then immediately notify the shipping carrier (responsible party for any transportation damage) and SYNRADreg See the inventory section with in the Introduction chapter of the Operation Manual for additional information

2 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

Top Foam notch

Bottom Foam notch

Donrsquot forget to remove the three (3) cap screws on the lens aperture cover if a

focusing lens is ordered

Unpacking (Continued)

Dust Cover

ImportantNote

Keep All Foam and Packaging you will need to re-use it when moving your laser to prevent damage that could void your warranty Refer to this guide and the Technical Reference chapters in the laserrsquos Operation Manual when re-packaging for shipping andor relocation Remove all accessory items not originally attached to the laser prior to re-packaging for shipping

Please refer to the examples above and the laserrsquos Operation Manual drawings located at the end of the Technical Reference Chapter

3 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

3 Connect the Marking Head DC power VDC cable into the Marking Headrsquos power supply

31 DC Power connection locations (for the Marking Head) to the power supply

Red (+)

Green ( ) Black

(-)

ImportantNote

The Marking Head requires a DC power supply capable of providing 30 VDC at 7 A minimum

If substituting power supplies use a well-regulated DC power supply in the range of 30 V to 32 V with no more than 3 V overshoot under a 10ndash90 modulation load The use of short leads and terminations rated for the appropriate output current is recom-mended

Do not reverse polarity when connecting the DC Power cable between the DC power supply and the Se-ries 48 laser

Attach the red (+) wire(s) from the DC Power cable to the positive (+) 48 VDC output terminal and attach the black (-) wire(s) from the DC Power cable to the negative (-) 48 VDC output terminal

Serious personal injury

Always use shielded cable when connecting your PWM Com-mand signal source to PWM PositivePWM Negative inputs

In electrically-noisy environments long lengths of unshielded wire act like an antenna and may generate enough voltage to trigger un-commanded lasing

Warning

Power Connections

4 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

Control Connections (Continued)

4 Connect the laserrsquos control BNC interface to the Marking Headrsquos laser control port

BNC Connector

41 Assure the ferrite bead is on the Marking Head side

51 Control connection locations (for the Marking Head)

5 Connect the other end of the BNC cable to the control input labeled CTRL located on the rear end of the laser

CTRL

5 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

6 The Ethernet connector is ready to be plugged into the PCrsquos Ethernet port and the USB cable is ready to be plugged from the FH Flyer Marking Head to the PC

61 To PC Ethernet port

To PC USB port

Control Connections (Continued)

Note If controlling your laser by a UC-2000 is desired go to the UC-2000 guide located on our website

Note To finish setup go to the FH Flyer WMP 6 Quick Start Guide located on our

3 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

3 Connect the Marking Head DC power VDC cable into the Marking Headrsquos power supply

31 DC Power connection locations (for the Marking Head) to the power supply

Red (+)

Green ( ) Black

(-)

ImportantNote

The Marking Head requires a DC power supply capable of providing 30 VDC at 7 A minimum

If substituting power supplies use a well-regulated DC power supply in the range of 30 V to 32 V with no more than 3 V overshoot under a 10ndash90 modulation load The use of short leads and terminations rated for the appropriate output current is recom-mended

Do not reverse polarity when connecting the DC Power cable between the DC power supply and the Se-ries 48 laser

Attach the red (+) wire(s) from the DC Power cable to the positive (+) 48 VDC output terminal and attach the black (-) wire(s) from the DC Power cable to the negative (-) 48 VDC output terminal

Serious personal injury

Always use shielded cable when connecting your PWM Com-mand signal source to PWM PositivePWM Negative inputs

In electrically-noisy environments long lengths of unshielded wire act like an antenna and may generate enough voltage to trigger un-commanded lasing

Warning

Power Connections

4 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

Control Connections (Continued)

4 Connect the laserrsquos control BNC interface to the Marking Headrsquos laser control port

BNC Connector

41 Assure the ferrite bead is on the Marking Head side

51 Control connection locations (for the Marking Head)

5 Connect the other end of the BNC cable to the control input labeled CTRL located on the rear end of the laser

CTRL

5 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

6 The Ethernet connector is ready to be plugged into the PCrsquos Ethernet port and the USB cable is ready to be plugged from the FH Flyer Marking Head to the PC

61 To PC Ethernet port

To PC USB port

Control Connections (Continued)

Note If controlling your laser by a UC-2000 is desired go to the UC-2000 guide located on our website

Note To finish setup go to the FH Flyer WMP 6 Quick Start Guide located on our

4 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

Control Connections (Continued)

4 Connect the laserrsquos control BNC interface to the Marking Headrsquos laser control port

BNC Connector

41 Assure the ferrite bead is on the Marking Head side

51 Control connection locations (for the Marking Head)

5 Connect the other end of the BNC cable to the control input labeled CTRL located on the rear end of the laser

CTRL

5 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

6 The Ethernet connector is ready to be plugged into the PCrsquos Ethernet port and the USB cable is ready to be plugged from the FH Flyer Marking Head to the PC

61 To PC Ethernet port

To PC USB port

Control Connections (Continued)

Note If controlling your laser by a UC-2000 is desired go to the UC-2000 guide located on our website

Note To finish setup go to the FH Flyer WMP 6 Quick Start Guide located on our

5 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

6 The Ethernet connector is ready to be plugged into the PCrsquos Ethernet port and the USB cable is ready to be plugged from the FH Flyer Marking Head to the PC

61 To PC Ethernet port

To PC USB port

Control Connections (Continued)

Note If controlling your laser by a UC-2000 is desired go to the UC-2000 guide located on our website

Note To finish setup go to the FH Flyer WMP 6 Quick Start Guide located on our

6 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

7 Before upgrading to a newer version of WinMark pro backup all existing mkh mark files and unin- stall prior version(s) of WinMark software httpwwwsynradcomsynraddocrootproducts marking_heads_softwarewinmark-sw

8 Download the latest version 6 WinMark pro driver from our website Exit all programs prior to In- stallation

9 To install WinMark pro v6 and associated device drivers on a Windowsreg 7 or Windowsreg Vistatrade operat- ing system right-click the lsquosetupexersquo file and choose lsquoRun as Administratorhelliprsquo

(WinMarkreg) v6 Software Installation

ImportantNote

When upgrading from a v4 build to version v6 the WinMark installer automatically performs a ldquoclean installrdquo because v6 is uses a different subset of registry keys The ldquoPerform Clean Installationrdquo and ldquoKeep Current Program Settingsrdquo options are grayed out to indicate this installation is a ldquoclean installationrdquo

Upgrading from one v6 build to another does allow the option of preserving existing WinMark settings in the computerrsquos System Registry Choose Yes to preserve current WinMark Pro v6 registry settings including custom date code formats object defaults shift codes auto startup info and saved serial numbers Choose No to erase all previous WinMark v6 Registry entries and perform a clean installation

Note Due to Microsoftrsquos implementation of registry virtualization Windows Vista may re-quire you to log on as an Administrator to perform certain functions like file impor-tation or to save custom date code formats

Laser Marking Software (WinMarkreg)

ImportantNote

Prior to installation of the WinMark laser marking software on your computer review the requirements in the WinMark Operation Manual remove power or unplug the USB cable from the FH Flyer head to prevent windows from arbitrarily assigning a USB driver that is not compatible with Flyerrsquos USB port protocols

Note Find the WinMark v6 Software release notes on our website Refer to the WinMark Operation Manual

7 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

WinMarkpro v6 Installation (continued)

Note If WinMark Pro is un-installed the NET package is not removed because these files may be used by other applications installed after the original WinMark installation

8 When the NET Framework installation us complete reboot if prompted to do so Otherwise the Win- Mark installer will continue

9 If Microsoft C++ Redistributable x86 file runtime components are not installed on the computer the installer will prompt you to click lsquoInstallrsquo to install C++ Redistributable files You must have these files installed to run WinMark Pro

10 Follow instructions in the installer dialog boxes to complete the WinMark Pro installation You must click lsquoI Agreersquo to accept the WinMark Pro license agreement and continue the installation

11 After installation is complete remember to turn on any anti-virus software

6 To install WinMark Pro v6 and associated device drivers on a Windowsreg operating system double- click the lsquosetupexersquo file

7 WinMark Pro v6 is a Microsoft NETtrade Framework-based application If Microsoft NET Framework Service Pack 1 or higher is not installed on the computer the installer will prompt you to click lsquoAc- ceptrsquo to install the NET Framework You must have the NET Framework runtime and associated files installed to run WinMark Pro

8 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

WinMark Launcher

12 As part of the software installation WinMark Launcher (Launcherexe) is placed in the Program Files WinMark folder and a shortcut is placed on the desktop Launcher allows non-administrative operators to load existing mkh files for marking without opening WinMarkrsquos Drawing Editor by selecting the lsquoOpen Drawingrsquo from the file menu

13 To add an Admin password so operators cannot lsquoModify Drawingrsquo Select lsquoModify Drawingrsquo which then opens the WinMarkpro application

Opening an existing mkh file Modifying an existing mkh file

Opening WinMarkpro through the Launcher

9 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

15 Using WinMark Prorsquos lsquoStartup Optionsrsquo within the Tools menu Launcher can be configured to load a specific file and to start marking automatically when the computer is powered up

WinMark pro

Browsing to the desired startup-file and automatically launch upon computer startup

Modifying an existing mkh file

14 Once the WinMark Pro application opens click the Tools menu and select lsquoGeneral Settingsrsquo

Password protecting mkh files

10 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

16 Digital Scope (DigScopeexe) is a stand-alone program included in the WinMark folder Use Digital Scope to test individual inputs and outputs turn the laser beam on or off or adjust the laserrsquos output power level This ldquomanualrdquo control is especially useful when testing or troubleshooting IO connections tofrom the marking head

WinMark Digital Scope

Digital Scope Application on the WinMark Pro folder

Samples folder on the WinMark Pro folder

17 The Samples folder is also placed in the WinMark folder during installation This folder contains a sample communications DLL Microsoftreg Visual Basicreg Microsoftreg Visual C++reg and Microsoftreg Creg (in a NETtrade framework) sample code that demonstrates the use of WinMarkrsquos ActiveMarktrade control methods a folder of importable bitmap and vector graphics files and sample mark files illustrating all of WinMark Prorsquos available stroke fonts

11 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

Laser Markers are pre-configured at the factory to a fixed address of 192168100100 This allows you to make a peer-to-peer Ethernet connection Your computerrsquos Ethernet settings are determined by your facil-ityrsquos computer network The FH Marking Head requires a connection to a computer with a static IP address if not connected to a local network (Peer to Peer) Reference the FH Flyer Operation Manual located on our website for more information

Set your computerrsquos static IP address

18 Disconnect the computer from your local network

19 Turn off Dynamic Host Configuration Protocol (DHCP) if enabled and create a static IP address for your computer

WinMarkpro v6 Communication Configuration

Note The exact steps may vary depending on your operating system

a From the Start menu go to Settings and choose Network Connections

b Double-click on the appropriate Local Area Network (LAN)

c Locate the LANrsquos Internet Protocol (TCPIP) properties

d Select ldquoUse the following IP addressrdquo and enter the following information

IP Address 192168100101 Subnet Mask 2552552550

e Click OK to submit the changes

8 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

WinMark Launcher

12 As part of the software installation WinMark Launcher (Launcherexe) is placed in the Program Files WinMark folder and a shortcut is placed on the desktop Launcher allows non-administrative operators to load existing mkh files for marking without opening WinMarkrsquos Drawing Editor by selecting the lsquoOpen Drawingrsquo from the file menu

13 To add an Admin password so operators cannot lsquoModify Drawingrsquo Select lsquoModify Drawingrsquo which then opens the WinMarkpro application

Opening an existing mkh file Modifying an existing mkh file

Opening WinMarkpro through the Launcher

9 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

15 Using WinMark Prorsquos lsquoStartup Optionsrsquo within the Tools menu Launcher can be configured to load a specific file and to start marking automatically when the computer is powered up

WinMark pro

Browsing to the desired startup-file and automatically launch upon computer startup

Modifying an existing mkh file

14 Once the WinMark Pro application opens click the Tools menu and select lsquoGeneral Settingsrsquo

Password protecting mkh files

10 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

16 Digital Scope (DigScopeexe) is a stand-alone program included in the WinMark folder Use Digital Scope to test individual inputs and outputs turn the laser beam on or off or adjust the laserrsquos output power level This ldquomanualrdquo control is especially useful when testing or troubleshooting IO connections tofrom the marking head

WinMark Digital Scope

Digital Scope Application on the WinMark Pro folder

Samples folder on the WinMark Pro folder

17 The Samples folder is also placed in the WinMark folder during installation This folder contains a sample communications DLL Microsoftreg Visual Basicreg Microsoftreg Visual C++reg and Microsoftreg Creg (in a NETtrade framework) sample code that demonstrates the use of WinMarkrsquos ActiveMarktrade control methods a folder of importable bitmap and vector graphics files and sample mark files illustrating all of WinMark Prorsquos available stroke fonts

11 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

Laser Markers are pre-configured at the factory to a fixed address of 192168100100 This allows you to make a peer-to-peer Ethernet connection Your computerrsquos Ethernet settings are determined by your facil-ityrsquos computer network The FH Marking Head requires a connection to a computer with a static IP address if not connected to a local network (Peer to Peer) Reference the FH Flyer Operation Manual located on our website for more information

Set your computerrsquos static IP address

18 Disconnect the computer from your local network

19 Turn off Dynamic Host Configuration Protocol (DHCP) if enabled and create a static IP address for your computer

WinMarkpro v6 Communication Configuration

Note The exact steps may vary depending on your operating system

a From the Start menu go to Settings and choose Network Connections

b Double-click on the appropriate Local Area Network (LAN)

c Locate the LANrsquos Internet Protocol (TCPIP) properties

d Select ldquoUse the following IP addressrdquo and enter the following information

IP Address 192168100101 Subnet Mask 2552552550

e Click OK to submit the changes

9 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

15 Using WinMark Prorsquos lsquoStartup Optionsrsquo within the Tools menu Launcher can be configured to load a specific file and to start marking automatically when the computer is powered up

WinMark pro

Browsing to the desired startup-file and automatically launch upon computer startup

Modifying an existing mkh file

14 Once the WinMark Pro application opens click the Tools menu and select lsquoGeneral Settingsrsquo

Password protecting mkh files

10 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

16 Digital Scope (DigScopeexe) is a stand-alone program included in the WinMark folder Use Digital Scope to test individual inputs and outputs turn the laser beam on or off or adjust the laserrsquos output power level This ldquomanualrdquo control is especially useful when testing or troubleshooting IO connections tofrom the marking head

WinMark Digital Scope

Digital Scope Application on the WinMark Pro folder

Samples folder on the WinMark Pro folder

17 The Samples folder is also placed in the WinMark folder during installation This folder contains a sample communications DLL Microsoftreg Visual Basicreg Microsoftreg Visual C++reg and Microsoftreg Creg (in a NETtrade framework) sample code that demonstrates the use of WinMarkrsquos ActiveMarktrade control methods a folder of importable bitmap and vector graphics files and sample mark files illustrating all of WinMark Prorsquos available stroke fonts

11 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

Laser Markers are pre-configured at the factory to a fixed address of 192168100100 This allows you to make a peer-to-peer Ethernet connection Your computerrsquos Ethernet settings are determined by your facil-ityrsquos computer network The FH Marking Head requires a connection to a computer with a static IP address if not connected to a local network (Peer to Peer) Reference the FH Flyer Operation Manual located on our website for more information

Set your computerrsquos static IP address

18 Disconnect the computer from your local network

19 Turn off Dynamic Host Configuration Protocol (DHCP) if enabled and create a static IP address for your computer

WinMarkpro v6 Communication Configuration

Note The exact steps may vary depending on your operating system

a From the Start menu go to Settings and choose Network Connections

b Double-click on the appropriate Local Area Network (LAN)

c Locate the LANrsquos Internet Protocol (TCPIP) properties

d Select ldquoUse the following IP addressrdquo and enter the following information

IP Address 192168100101 Subnet Mask 2552552550

e Click OK to submit the changes

10 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

16 Digital Scope (DigScopeexe) is a stand-alone program included in the WinMark folder Use Digital Scope to test individual inputs and outputs turn the laser beam on or off or adjust the laserrsquos output power level This ldquomanualrdquo control is especially useful when testing or troubleshooting IO connections tofrom the marking head

WinMark Digital Scope

Digital Scope Application on the WinMark Pro folder

Samples folder on the WinMark Pro folder

17 The Samples folder is also placed in the WinMark folder during installation This folder contains a sample communications DLL Microsoftreg Visual Basicreg Microsoftreg Visual C++reg and Microsoftreg Creg (in a NETtrade framework) sample code that demonstrates the use of WinMarkrsquos ActiveMarktrade control methods a folder of importable bitmap and vector graphics files and sample mark files illustrating all of WinMark Prorsquos available stroke fonts

11 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

Laser Markers are pre-configured at the factory to a fixed address of 192168100100 This allows you to make a peer-to-peer Ethernet connection Your computerrsquos Ethernet settings are determined by your facil-ityrsquos computer network The FH Marking Head requires a connection to a computer with a static IP address if not connected to a local network (Peer to Peer) Reference the FH Flyer Operation Manual located on our website for more information

Set your computerrsquos static IP address

18 Disconnect the computer from your local network

19 Turn off Dynamic Host Configuration Protocol (DHCP) if enabled and create a static IP address for your computer

WinMarkpro v6 Communication Configuration

Note The exact steps may vary depending on your operating system

a From the Start menu go to Settings and choose Network Connections

b Double-click on the appropriate Local Area Network (LAN)

c Locate the LANrsquos Internet Protocol (TCPIP) properties

d Select ldquoUse the following IP addressrdquo and enter the following information

IP Address 192168100101 Subnet Mask 2552552550

e Click OK to submit the changes

11 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

FH MARKING HEAD

FLYER

Laser Markers are pre-configured at the factory to a fixed address of 192168100100 This allows you to make a peer-to-peer Ethernet connection Your computerrsquos Ethernet settings are determined by your facil-ityrsquos computer network The FH Marking Head requires a connection to a computer with a static IP address if not connected to a local network (Peer to Peer) Reference the FH Flyer Operation Manual located on our website for more information

Set your computerrsquos static IP address

18 Disconnect the computer from your local network

19 Turn off Dynamic Host Configuration Protocol (DHCP) if enabled and create a static IP address for your computer

WinMarkpro v6 Communication Configuration

Note The exact steps may vary depending on your operating system

a From the Start menu go to Settings and choose Network Connections

b Double-click on the appropriate Local Area Network (LAN)

c Locate the LANrsquos Internet Protocol (TCPIP) properties

d Select ldquoUse the following IP addressrdquo and enter the following information

IP Address 192168100101 Subnet Mask 2552552550

e Click OK to submit the changes

12 QSG WinMarkpro v6 for FH Flyer MH Ver21

a Novanta company

WinMarkproreg v6 for the FH Marking Head Quick Start Guide

Marking headrsquos USB driver

WinMark Pro (WMP) installs a specialized USB driver that communicates with the marking head and the La-ser During computer boot-up the Windows OS automatically starts the USB driver as a service Once started the driver can be accessed by WinMark Pro WinMark Launcher or Digital Scope

If the Found New Hardware Wizard dialog appears when your marking head is first connected to the com-puterrsquos USB port perform the following steps

20 Download USB driver from web site run the USB installexe When asked ldquoCan Windows connect to Windows Update to search for softwarerdquo Click lsquodo not this timersquo and click lsquoNextrsquo

21 When prompted ldquoWhat do you want the wizard to dordquo Click lsquoInstall the software automatically (Recommended)rsquo and click lsquoNextrsquo

22 Click ldquoFinishrdquo to complete the USB driver installation for the Marking Head device

WinMark File Import Filters

WinMark Pro automatically loads the File Import Filters during installation These filters allow you to import a wide variety of graphi file formats See the WinMark pro Operation Manual for details

After the un-install is complete some WinMark components like MKH mark files will remain To completely remove all WinMark-related files go to CProgram Files and delete the WinMark folder

Uninstalling WinMark Pro

If you decide to remove WinMark pro software from your computer perform the following steps

22 Click the lsquoStartrsquo button on the taskbar

23 Select lsquoProgramsrsquo and then locate the SYNRAD WinMark pro folder

24 Click the lsquoUninstallrsquo SYNRAD WinMark icon

25 Follow the on-screen instructions

Note Before installing or upgrading WinMark Pro software first disconnect power or unplug the USB cable from the Marking head this ensures that the Windows OS will load and install the latest marking head USB driver otherwise Windows will arbitrarily assign a USB driver that is not compatible with the marking head USB port protocols If this happens see the Trouble-shooting section of the Marking Headrsquos Operator Manual or the WMP Operatorrsquos Manual for information on the re-installing the correct USB driver

WinMarkpro v6 Configuration (continued) optional USB driver

WinMark Pro (WMP) installs a specialized USB driver that communicates with the marking head and the Laser (not recommended for manufacturing environments) During computer boot-up the Windows OS automatically starts the USB driver as a service Once started the driver can be accessed by WinMark Pro WinMark Launcher or Digital Scope

• Laser Marking Software (WinMark)
• (WinMark) v6 Software Installation
• WinMarkpro v6 Installation (continued)
• WinMark Launcher
• WinMark pro
• WinMark Digital Scope
• WinMarkpro v6 Communication Configuration
• WinMarkpro v6 Configuration (continued) optional USB driver