table of contentsmultimedia.3m.com/mws/media/753877o/medical-specialties-tape... · table of...
TRANSCRIPT
Version 8.1 August 2013
Table of Contents
New Products NP1–NP6
Product Categories/Technical Data/Samples 1–66A. Double Coated Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11
B. Single Coated Film Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–27
Polyethylene and Polyolefin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–20
Polyester, Incise and Polyurethane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21–27
C. Nonwoven and Woven Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28–42
Rayon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28–32
Polyester and Polyester Blends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33–36
Polyurethane and Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37–41
D. Foam Tapes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42–47
E. Specialty Films . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48–59
F. Specialty Tapes and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50–52
G. Release Liners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53–56
H. Fasteners, Closures and Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57–59
I. Diagnostic Tapes and Films . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60–65
J. Custom Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
From component selection to market introduction, 3M Medical Specialties offers more technologies and services to help make your product a success.
See Numerical Product Index — Next Page3M Medical Specialties and OEM Products
The Trusted Source
Version 8 .1 August 2013
1115NS Tube and Cord Organizer 57
1361 83# Paper Release Liner 53 55
1503 SC Tan Polyethylene Tape 12 16
1504XL Hi-Tack Transfer Adhesive, 4 mil 2 10
1509 DC Polyethylene Tape 1 4
1510 DC HD Polyethylene Tape 1 5
1513 DC Polyester Tape 2 7
1516 SC Polyester Tape 21 23
1521 SC Polyethylene Tape 12 15
1522 DC Polyethylene Tape 1 5
1523 Blush Tan SC Polyethylene Tape 12 15
1524 Transfer Adhesive 2 9
1524A Transfer Adhesive on Premium Liner 2 11
1525L SC Polyethylene Tape on Liner 12 16
1526 SC Polyethylene Tape 12 17
1527 Perforated PE/EVA Tape 13 18
1527ENP Embossed PE/EVA Tape 13 19
1527LX Perforated PE/EVA Tape on Liner 13 19
1529 Printable Rayon Nonwoven Tape 28 30
1530 White Rayon Nonwoven Tape 28 30
1530L White Rayon NW Tape on Liner 28 31
1533 Tan Rayon Nonwoven Tape 28 31
1533L Tan Rayon NW Tape on Liner 28 32
1538 White Rayon Woven Tape 37 40
1538L White Rayon Woven Tape on Liner 37 41
1567 DC Hi Adhesion PET Tape 2 6
1577 DC 2-in-One Polyester Tape 2 8
1587 DC Gentlest 2-in-One PET Tape 2 6
1597 DC 2-in-One PET Tape 2 9
1772 White PE Foam Tape 42 44
1773 White PE Foam Tape 42 44
1774T Tan PE Foam Tape 42 45
1774W White PE Foam Tape 42 45
1776 White Spunlace Nonwoven Tape 33 35
1785 Heat Sealable Rayon NW Tape 28 32
2475/2475P SC TPE Film w/Silicone PSA NP2 NP4
2476/2476P SC Nonwoven w/Silicone PSA NP2 NP5
2477/2477P DC Gentle 2-in-One Si/Acr PSA NP2 NP6
7330 Low Profile Loop Fastener 57 58
7331 Low Profile Loop with Adhesive 57 58
7334 Low Profile Hook Fastener 57 58
7335 Low Profile Hook with Adhesive 57 58
7336 Low Profile Hook w/Hi-Tack PSA 57 58
7337 Low Profile Loop w/Hi-Tack PSA 57 58
9776 Tan PE Foam Tape 42 45
9777L Ivory PVC Foam Tape 42 46
9779B Blue Flexform Closure Tape, Roll 59
9779W White Flexform Closure Tape, Roll 59
9780 Blue PVC Foam Tape 42 47
9781 Ivory PVC Foam Tape 42 46
9785 Light Tan PVC Foam Tape 42 47
9792R Aluminum Diagnostic Tape 60 62
9793R Polyolefin Diagnostic Tape 60 62
9795R Adv. Polyolefin Diagnostic Tape 60 63
9812N Neoprene Sheath/Finger Cot 58
9818 B/D/G/J Flexfoam Closures/Clips 59
9823D Blue Flexform Tape Strips 61
9830 Polyethylene Incise Tape 21 24
9832F Breathable Polyurethane Film 21 26
9833 Breathable PUR Tape on White Carrier 21 27
9834/B/P/T Breathable PUR Tape on White Carrier; Translucent, Pink, Tan and Blue 21 25
9835 White SC PE/EVA Tape 13 20
9836 Breathable PUR Tape on White Liner with Clear Poly Carrier 21 26
9860 SC Polyester Tape 21 23
9865 Printable SC Polyethylene Tape 12 17
9865A Printable SC Polyethylene Tape 12 18
9874 DC Polyethylene Tape 1 7
9877 DC Polyester Tape 2 8
9880 Hydrogel Adhesive on Liner 50 52
9889 DC Polyethylene Tape 1 4
9904 Tan Hi-Tack PUR Nonwoven Tape 37 39
9907T Tan Polyurethane Nonwoven Tape 37 39
9907W White PUR Nonwoven Tape 37 39
9907HTW Hi-Tack White PUR Nonwoven Tape 37 40
9916 Tan Spunlace NW Tape 33 35
9917 DC Spunlace Nonwoven Tape 1, 33 10, 36
9943/9943J Thin Hydrocolloid Tape 50 51
9944 Tackified Hydrocolloid Tape 50 51
9945J Heat Sealable Hydrocolloid Tape 50 52
9948 Conformable Breathable Incise 21 25
9952 SC Polyester Tape 21 24
9954 Fluorosilicone Hybrid Release Liner, Polyester 53 54
9955 Fluoropolymer Release Liner, Polypropylene 53 54
9956 Fluoropolymer Release Liner, Polyester 53 55
9960 Anti-fog Hydrophilic Polyester Film 48, 61 65
9962 Anti-fog Hydrophilic Polyester Film 48, 61 64
9964 SC Clear Polyester Diagnostic Tape 60 63
9965 DC White Polyester Diagnostic Tape 60 64
9967 Heat Sealable Polyester Film 48 49
9968 63# Paper Release Liner 53 56
Data Sample Data SampleIndex
All statements, technical information and recommendations herein are based on tests and/or data we believe to be reliable, but the accuracy or completeness thereof is not guaranteed. Before using any of the products referenced herein, user shall determine the
suitability of the product for its intended use, and user assumes all risk and liability whatsoever in connection with their application.
Version 8.1 August 2013
3M — Over a Century of InnovationCustomers have relied upon 3M for innovative products since
1902. With access to more than 100 core 3M technologies,
we can meet the needs of our medical business-to-business
customers with existing products or by developing new ones.
50 Years Health Care Expertise3M is a trusted brand in health care with over 50 years of
experience. We have a tradition of presenting customer
focused solutions in medical tape, surgical drapes, wound care
dressings, indicators and prepping product categories. Unique
3M technologies have resulted in more than 10,000 3M Health
Care products. 3M Medical Specialties offers innovative
product solutions for your medical applications.
Wide Ranging ApplicationsDraw on our unique 3M technologies in hypoallergenic medical
tapes, films, specialty coatings, and materials for your next
product innovation.
ConfidentialityWe ensure a confidential approach to safeguard the integrity of
your product development process.
Delivered ValueOur comprehensive product testing and clinical support can
help bring your products to market faster.
Customer FocusedYour product development requirements are supported by our
experienced customer-focused team.
Quality and Safety You Can Depend OnOur components are backed by comprehensive safety, clinical
and quality testing, as well as regulatory documentation.
Prompt, Reliable Custom ServiceCustom roll slitting and shipping are included in our price to
you. Reliable delivery dates allow you to reduce inventory costs.
Global SupportWe have experts placed around the world to provide you with
critical global knowledge and support.
Trust your medical product needs to the company that is known for innovation, quality and service
Imagine the Possibilities Partner with 3M Medical Specialties
The Trusted Source
3M Medical Specialties provides innovative products and technology,
AND product and clinical experts to support your business growth.
Version 8.1 August 2013
3M’s International Presence Provides You with Global Knowledge and Support
Product and Safety InformationUser is solely responsible for determining the suitability of
3M samples and products for the intended use including any
necessary safety or toxicity assessment. 3M will provide
Material Safety Data Sheets and results of toxicity testing upon
request. In every case before using any product in full scale
production users should conduct their own tests to determine
to their own satisfaction whether the product is of acceptable
quality and is suitable for their particular purposes under their
own operating conditions.
NoticeNothing contained herein shall be construed to imply
the nonexistence of any relevant patents or to constitute a
permission, inducement or recommendations to practice any
invention covered by any patent, without authority from the
owners of this patent.
Warranty InformationAll statements, technical information and recommendations
herein are based on tests 3M believes to be reliable, but
the accuracy or completeness thereof is not guaranteed.
3M warrants only that products will meet 3M’s specifications
at the time of shipment to the customer. 3M does not offer any
other warranty and does not warrant the performance, safety
or such other characteristics of Products in combination
with other materials. 3M specifically DOES NOT warrant
Products for any intended or unintended uses (whether or
not foreseeable); for compatibility or suitability with other
components or compatibility with any methods of manufacture
or conversion. The foregoing warranty is made in lieu of all
other warranties, expressed or implied, including the implied
warranties of merchantability, fitness for a particular purpose
and freedom from non-infringement.
Limitation of RemediesIf products are proven not to meet 3M’s specifications, the sole
and exclusive remedy available and 3M’s only obligation shall
be, at 3M’s option, to replace such quantity of Products which
are proven out of specification or to refund the purchase price
paid for Products.
Limitations of LiabilitiesThe remedies provided herein are exclusive remedies against
3M for any alleged or actual nonconformance to specifications
or defect or other failure in products or for 3M’s performance
of its supply obligations. Under no circumstances is 3M liable
for any direct, indirect, incidental, special or consequential
damages (including lost profits) in any way related to the
product under any theory of law including, but not limited to,
negligence and strict liability.
Ordering InformationTo place an order contact our Customer Service Reps at:
800-742-1994 (U.S.). To have a sales representative contact
you, to request samples or clinical and safety summaries,
please visit the website at www.3M.com/MedicalSpecialties
or contact us at 3M Health Care Helpline at 800-228-3957
(U.S.) or 651-604-5599 (International). For international
inquiries, please contact your local country representative.
A list of local/international contacts is available at
www.3M.com/MedicalSpecialties.
Visit our web site at www.3M.com/MedicalSpecialties for product
and services information, news about conferences we will be
attending, new product highlights or to make a direct inquiry.
Version 8.1 August 2013
3M Medical Specialties Product GuideThis guide will assist you in selecting the proper component
to be used in your medical device. It is an introduction to the
variety of innovative technologies manifested in our products.
Choosing a component supplier for your medical device is
a critical decision. You must be sure your source can supply
components that perform reliably and set you apart from your
competition. We are ISO 9001/ISO 13485/ EN 46001 certified;
we manufacture our products to current Good Manufacturing
Practices (GMP’s); and we provide documentation in the form
of product safety and information summaries.
Guide OrganizationThis guide is organized to provide you assistance in selecting
the correct product in your market segment / product use
category. Products are arranged by major type such that
technical data for similar products can be effectively compared
to help you select specific products for use in your device.
Following the technical data comparison sheets are actual
samples of each product. Underneath each sample is a
construction diagram of the tape along with a list of Key Features
which may help further guide you in your selection process.
Note: Components are medical grade unless otherwise specified.
Important NoteFor components listed in this guide (“Components”), statements regarding typical applications or reported uses are not intended
to suggest that these Components will perform as you require in your specific application. In some cases, various branded 3M
Health Care products are components similar to the components in this guide. In other cases, we know of such uses through
information provided by our customers. In all cases, the user of components listed in this guide (“Users”) is solely responsible for
determining the suitability of the Components in User’s specific application. 3M warrants only that the Components will meet
3M’s specifications at the time of shipment to the User. (See full warranty information on previous page and on the back cover).
Medical Specialties Website — Everything at your fingertips!Need more than samples? Want to compare side-by-side? Questions on tape in general? Relative to your market? Check out
our redesigned website at www.3M.com/MedicalSpecialties. In addition to being easy to navigate, we have a broad selection of
updated product and technical information complimented with easy-to-use Document Selector and product comparison feature.
Quick buttons allow you to get connected with 3M personnel as well as order samples or request additional information.
Between physical samples and on-line updated technical resources, 3M wants to help you make your project a success!
For all the information that you have come to expect from 3M,
go to www.3M.com/MedicalSpecialties.
Version 8.1 August 2013 6
Easily Accessible Technical Information Online!You can search for products you need for your unique application by product characteristics, such as Primary Application, Tape
Type, or Adhesive Type. Each product has in-depth technical information and you are able to compare up to four products side-by-
side. We have supporting clinical, safety, and MSDS information in the Document Selector, as well as in each product page.
Find product specifications
Compare Products!You can compare products side-by-side...
up to four products at a time
www.3M.com/MedicalSpecialties
Find supporting documentation
To compare up to 4 products, click here
Version 8.1 August 2013
3M Medical Specialties — New ProductsAs a world leader in medical innovation and technology, as well
as THE experts in material science and skin health, we would
like to highlight several of our newest product additions.
As is true with the entire 3M Medical Specialties line, our
new product offerings undergo safety and efficacy evaluations
before they are marketed. Typically they are tested for:
• ISO:10993-5 In vitro Cytotoxicity
• ISO:10993-5 MEM Elution Cytotoxicity
• ISO:10993-10 Primary Skin Irritation
• ISO:10993-10 Guinea Pig Sensitization
and may also include:
• 21-day Human Cumulative Irritancy test
• 200-Person Draize for contact sensitization
As the Trusted Source, when we add to our broad portfolio,
we ensure our products are backed by manufacturing standards
and rigid specifications. This is true whether the products are
standard line or custom made. Remember, these documents
are always available from 3M:
• Product Technical Information Sheet
• Clinical Data Summary
• Certificate of Conformance/Certificate of Analysis
• Test Methodology
• Material Safety Data Sheet
Products are manufactured under current Good Manufacturing
Practices in ISO 9001 certified facilities that comply with FDA
Quality Systems regulations (QSR) ISO 13485.
From component selection to market introduction, 3M offers
more new technologies and services to help make your
product a success!
Imagine the Possibilities Partner with 3M Medical Specialties
The Trusted Source
For more information on all 3M Medical Specialties products,
please visit our updated website at www.3M.com/MedicalSpecialties
New Products: NP1
Version 8.1 August 2013
New Products Selection Guide — Medical Tapes with 3M Silicone Adhesive
Single-Coated Tapes Double-Coated Tapes
Properties1 2475 2475P 2476 2476P 2477 2477P
Developmental Number MSX-6936A MSX-6936B MSX-6935A MSX-6935B MSX-6931A/B MSX-6932B
1. Sterilization2 EtO Only EtO Only EtO Only EtO Only EtO Only EtO Only
2. Hypoallergenic Yes Yes Yes Yes Yes Yes
3. Repeat Skin Contact Yes Yes Yes Yes Yes Yes
4. Conformable (L=Low; M=Medium; H=High) H H M M M M
5. Fluid Resistance Yes Yes Yes Yes Yes Yes
6. Typical MVTR gm/m2/24 hr 600 600 800 800 400 400
7. Typical Tensile, MDlbs/inch 2 2 16 16 5 5
Newtons/25mm 8.9 8.9 70 70 22 22
8. Elongation percentage 350 350 65 65 650 650
9. Typical Adhesion/(Faceside) Stainless Steel
oz/inch 3 3 3.35 4.5 3.6 / 17 3.5 / 17
Newtons/25mm 0.8 0.8 0.9 1.25 0.8 / 4.7 0.8 / 4.7
10. Tape Caliper without Liner
mil 4.6 4.6 14.6 14.6 7.2 7.2
millimeters 0.12 0.12 0.37 0.37 0.18 0.18
11. Adhesive Coating (each side)
mil 4.0 4.0 4.0 4.0 4.0 / 1.5 Si/Acr
4.0 / 1.5 Si/Acr
millimeters 0.10 0.10 0.10 0.10 0.10 / 0.04 0.10 / 0.04
12. Backing/Carrier Calipermil 0.6 0.6 10.6 10.6 1.5 1.5
millimeters 0.02 0.02 0.27 0.27 0.04 0.04
13. Liner Calipermil 2.0 3.5 2.0 3.5 2.0 / 3.3 3.5 / 3.3
millimeters 0.11 0.08 0.11 0.09 0.09 / 0.08 0.09 / 0.08
14. Liner Type Polyester Polypropylene Polyester Polypropylene Polyester/ Paper
Polypropylene/ Paper
15. Typical Liner Release gm/inch 42 10 42 10 Poly — 50Paper — 7
Poly — 9Paper — 10
16. Maximum Widthinches 24 24 12 12 23 23
centimeters 61 61 30.5 30.5 58 58
17. Maximum Lengthyards 200 200 100 100 200 200
meters 183 183 91 91 183 183
18. Approx. Roll Diameterinches 9 10.5 9.25 9.5 12 12.5
centimeters 23 27 23.5 24 31 32
19. Shelf Life years 2 2 2 2 TBD TBD
1 Properties listed are based on limited testing and subject to change . 2 Recommended suitability based on the processability of product through typical EtO sterilization conditions .
Table Revised August 2013
New Products: NP2
Version 8.1 August 2013
New
Pro
duct
s —
3M
Med
ical
Sili
cone
Adh
esiv
e Ta
pes
2475
2475
P98
3424
7624
76P
1776
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T24
T48
T72
New Products: NP3
Version 8.1 August 20134
Key Features #2475P is supplied on a clear polypropylene film liner with 3M proprietary fluoropolymer release chemistry on one side. Heavier weight liner for improved handling during converting has a premium (lower) release for easy release by the end user.
#2475PThermoplastic Elastomer (TPE) Film Tape with Silicone Adhesive (4.6 mil/0.12mm) 3.5 mil LinerEtO OnlyDevelopment Ref.: MSX-6936B
Backing 0.6 mil Clear TPE Film
Adhesive 4 mil 3M Medical Silicone Adhesive
Liner 3.5 mil Clear Polypropylene Film liner, one side fluoropolymer release
Wind Orientation — Liner Outside
Key Features Liquid barrier, breathable, thin, conformable tape with 3M proprietary silicone adhesive for gentle skin adhesion on one side. #2475 is supplied on a clear polyester film liner with hybrid fluorosilicone release chemistry on one side.
#2475 Thermoplastic Elastomer (TPE) Film Tape with Silicone Adhesive (4.6 mil/0.12mm) 2 mil LinerEtO OnlyDevelopment Ref.: MSX-6936A
Possible Uses Attaching medical or retail devices to fragile skin in geriatric or pediatric applications. Laminates well with other tapes to make new or unique multi-layer constructions.
Backing 0.6 mil Clear TPE Film
Adhesive 4 mil 3M Medical Silicone Adhesive
Liner 2 mil Clear Polyester Film liner, one side fluorosilicone release
Wind Orientation — Liner Outside
New Products: NP4
Version 8.1 August 2013
Key Features Breathable, strong, conformable tape with 3M proprietary silicone adhesive for gentle skin adhesion on one side. #2476 Nonwoven tape is supplied on a clear polyester film liner with hybrid fluorosilicone release chemistry on one side.
#2476 White Spunlace Nonwoven Tape with Silicone Adhesive (14.6 mil/0.37mm) 2 mil LinerEtO OnlyDevelopment Ref.: MSX-6935A
Possible Uses Attaching medical or retail devices to fragile skin in applications such as sensor attachment where multiple product layers are not required.
Backing White Polyester Spunlace Nonwoven laminate, 1.3 oz/yd2 (~30gm/m2)
Adhesive 4 mil 3M Medical Silicone Adhesive
Liner 2 mil Clear Polyester Film liner, one side fluorosilicone release
Wind Orientation — Liner Inside
Key Features #2476P is supplied on a clear polypropylene film liner with 3M proprietary fluoropolymer release chemistry on one side. Heavier weight liner for improved handling during converting has a premium (lower) release for easy release by the end user.
#2476P White Spunlace Nonwoven Tape with Silicone Adhesive (14.6 mil/0.37mm) 3.5 mil LinerEtO OnlyDevelopment Ref.: MSX-6935B
Possible Uses Attaching medical or retail devices to fragile skin in applications such as sensor attachment where multiple product layers are not required.
Backing White Polyester Spunlace Nonwoven laminate, 1.3 oz/yd2 (~30gm/m2)
Adhesive 4 mil 3M Medical Silicone Adhesive
Liner 3.5 mil Clear Polypropylene Film liner, one side fluoropolymer release
Wind Orientation — Liner Inside
New Products: NP5
Version 8.1 August 2013
Key Features 3M #2477 is a double-coated differential silicone/acrylic adhesive tape designed for medical and retail lamination applications. The tape is supplied on a flexible TPE carrier with a paper release liner on the acrylic adhesive side of the tape. The 3M proprietary silicone adhesive side is protected by a fluorosilicone release polyester film liner.
#2477 2-in-One Silicone/Acrylic Differential Tape (4.6 mil/0.12mm) 2 mil LinerEtO OnlyDevelopment Ref.: MSX-6931A/B
Liner 60# Silicone-coated Paper Release Liner
Adhesive 1.5 mil 3M non-tackified Acrylic Adhesive
Carrier 1.5 mil Clear TPE Film
Adhesive 4 mil 3M Medical Silicone Adhesive
Liner 2 mil Clear Polypropylene Film liner, one side fluoropolymer release
Wind Orientation — Polyester Film Liner Outside
Key Features 3M #2477P is a double-coated differential silicone/gentle acrylic adhesive tape designed for medical and retail lamination applications. The tape is supplied on a flexible TPE carrier with a paper release liner on the gentle acrylic adhesive side of the tape. The 3M proprietary silicone adhesive side is protected by a premium fluoropolymer-release polypropylene film liner.
#2477P 2-in-One Silicone/Acrylic Differential Tape (4.6 mil/0.12mm) 3.5 mil LinerEtO OnlyDevelopment Ref.: MSX-6932B
Liner 60# Silicone-coated Paper Release Liner
Adhesive 1.5 mil 3M non-tackified Acrylic Adhesive
Carrier 1.5 mil Clear TPE Film
Adhesive 4 mil 3M Medical Silicone Adhesive
Liner 3.5 mil Clear Polypropylene Film liner, one side fluoropolymer release
Wind Orientation — Polypropylene Film Liner Outside
New Products: NP6
Version 8.1 August 20131
Medical Double Coated Tapes & Transfer Adhesive Selection Guide — Part 1
Polyethylene Polyester NW
Properties1 1509 1510 1522 9874 9889 9917
1. Sterilization2 (G=Gamma; E=Ethylene Oxide; S=Steam Autoclave) G, E G, E G*, E G*, E G, E G*, E
2. Hypoallergenic Yes No Yes Yes Yes Yes
3. Repeat Skin Contact No No Yes Yes No Yes
4. Conformable (L=Low; M=Medium; H=High) M H M M M H
5. Fluid Resistance Yes Yes Yes Yes Yes No
6. Typical Tensile MDlbs/inch 4.5 1.8 4.5 4.5 4.5 17
Newtons/25mm 20 8 20 20 20 75
7. Elongation percentage 200 800 200 200 200 30
8. Typical Adhesion/(Faceside) Stainless Steel
oz/inch 53 45 LDPE 25 19 53 27/23
Newtons/25mm 14.7 12.5 7 5.3 14.7 7.5/6.4
9. Tape Caliper without Linermil 4.9 3.8 6.3 4.9 4.9 12
millimeters 0.12 0.10 0.16 0.12 0.12 0.3
10. Adhesive Coating (each side)
mil 0.95 1.4 1.65 0.95 0.95 1.4
millimeters 0.02 0.04 0.04 0.02 0.02 0.04
11. Carrier Calipermil 3.0 1.0 3.0 3.0 3.0 12
millimeters 0.08 0.03 0.08 0.08 0.08 0.3
12. Liner Calipermil 4.5 3.2 4.5 3.6 3.5 3.6
millimeters 0.11 0.08 0.11 0.09 0.09 0.09
13. Liner Weight lbs/ream 80 54 80 60 60 62
14. Maximum Liner Releasegm/inch 50 40 30 30 50 55
Newtons/25mm 0.49 0.39 0.29 0.29 0.49 0.54
15. Maximum Widthinches 48 27 48 48 48 48
centimeters 122 69 122 122 122 122
16. Maximum Lengthyards 600 360 550 700 700 400
meters 548 329 503 640 640 366
17. Approx. Roll Diameterinches 17 13.5 17 17 17 17
centimeters 43 34 43 43 43 43
18. Shelf Life years 2 2 3 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application . 2 Recommended suitability based on the processability of product through typical sterilization conditions .
*Reduced adhesion levels and increased liner release may occur after gamma irradiation .
Table Revised November 2012
Version 8.1 August 2013 2
Medical Double Coated Tapes & Transfer Adhesive Selection Guide — Part 2
Polyester Carrier Transfer Adhesive
Properties1 1513 1567 1577 1587 1597 9877 1504XL 1524 1524A
1. Sterilization2 (G=Gamma; E=Ethylene Oxide; S=Steam Autoclave) G, E, S G, E G, E, S G, E G, E G, E, S G*, E G, E, S G, E, S
2. Hypoallergenic Yes Yes Yes Yes Yes Yes Yes Yes Yes
3. Repeat Skin Contact No No No Yes Yes No No No No
4. Conformable (L=Low; M=Medium; H=High) L L L L L L M H H
5. Fluid Resistance Yes Yes Yes Yes Yes Yes Yes No No
6. Typical Tensile MDlbs/inch 20 20 20 20 20 20 N/A N/A N/A
Newtons/25mm 89 89 89 89 89 89 N/A N/A N/A
7. Elongation percentage 135 135 135 135 135 135 N/A N/A N/A
8. Typical Adhesion/(Faceside) Stainless Steel
oz/inch 61 175 A/SR 48/100
A/SR 20/100
A/SR 40/175 120 200 80 80
Newtons/25mm 17 48.6 13/28 6/28 11/48 33.4 55.6 22 22
9. Tape Caliper without Linermil 3.4 5 3.6 3.4 4.3 4.5 4.0 2.5 2.5
millimeters 0.09 0.13 0.09 0.09 0.11 0.11 0.10 0.06 0.06
10. Adhesive Coating (each side)
mil 1.2 2 1.4 1/1.4 1.7/1.7 1.75 4.0 2.5 2.5
millimeters 0.03 0.05 0.04 0.03/0.04 0.04/0.04 0.04 0.10 0.06 0.06
11. Carrier Calipermil 0.92 0.92 0.92 0.92 0.92 0.92 N/A N/A N/A
millimeters 0.02 0.02 0.02 0.02 0.02 0.02 N/A N/A N/A
12. Liner Calipermil 4.5 3.5 3.5 3.5 3.5 3.6 3.6 3.0 4.5
millimeters 0.11 0.09 0.09 0.09 0.09 0.09 0.09 0.08 0.11
13. Liner Weight lbs/ream 80 60 60 60 60 62 62 54 78
14. Maximum Liner Releasegm/inch 50 70 70 70 70 70 70 29 40
Newtons/25mm 0.49 0.69 0.69 0.69 0.69 0.69 0.69 0.28 0.39
15. Maximum Widthinches 48 48 48 48 48 48 6 48 48
centimeters 122 122 122 122 122 122 15 122 122
16. Maximum Lengthyards 700 700 700 700 700 700 600 400 400
meters 640 640 640 640 640 640 549 366 366
17. Approx. Roll Diameterinches 17 17 17 17 17 17 15 12 13
centimeters 43 43 43 43 43 43 38 31 33
18. Shelf Life years 2 2 2 2 TBD 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only. It is the customer’s responsibility to determine the final suitability of our products for use in their application. 2 Recommended suitability based on the processability of product through typical sterilization conditions.
*Reduced adhesion levels and increased liner release may occur after gamma irradiation.
Table Revised November 2012
Version 8.1 August 20133
Doub
le C
oate
d Ta
pes/
Tran
sfer
Adh
esiv
e
1509
/ 98
8915
1015
2298
7415
1315
67/
1597
(S
RB)
1577
/ 15
97
(Acr
)
1577
/ 15
87
(SR)
15
87
(Acr
) 98
7799
1715
04XL
1524
/ 15
24A
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
Version 8.1 August 20134
Key Features Excellent adhesion to skin, polyethylene and most fabrics used in surgical and medical devices. Some anti-wetting surface treatments may affect adhesion level.
#1509 Double Coated Polyethylene Tape (4.9 mil/0.12mm) 80# Liner Gamma, EtO
Adhesive 0.95 mil Hypoallergenic, Acrylate
Carrier 3 mil Transparent Polyethylene film
Adhesive 0.95 mil Hypoallergenic, Acrylate
Liner 80# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Key Features Same as #1509 above, except has lighter weight liner. May die cut somewhat easier than #1509.
#9889 Double Coated Polyethylene Tape (4.9 mil/0.12mm) 60# Liner Gamma, EtO
Adhesive 0.95 mil Hypoallergenic, Acrylate
Carrier 3 mil Transparent Polyethylene film
Adhesive 0.95 mil Hypoallergenic, Acrylate
Liner 60# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 20135
Key Features The special high tack adhesive quickly and strongly attaches to a wide variety of substrates. The highly conformable carrier is particularly suitable for contoured surfaces or devices subject to flexing or folding.
#1510 Double Coated Hi-Tack Conformable Polyethylene Tape (3.8 mil/0.1mm) 54# Liner Gamma, EtO
Adhesive 1.4 mil Synthetic Rubber-based
Carrier 1 mil Transparent Polyethylene film
Adhesive 1.4 mil Synthetic Rubber-based
Liner 54# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Key Features Excellent for adhesion to skin, especially where repeated skin contact is anticipated.
#1522 Double Coated Polyethylene Tape (6.3 mil/0.16mm) 80# Liner Gamma, EtO
Reported Uses Securing a toupee to scalp, wound care and other devices adhered to delicate skin such as elderly or infant skin.
Adhesive 1.65 mil Hypoallergenic Acrylate
Carrier 3.0 mil Transparent Polyethylene film
Adhesive 1.65 mil Hypoallergenic Acrylate
Liner 80# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 20136
Key Features Gentle, hypoallergenic adhesive combined with an aggressive synthetic rubber-based one in a “2-in-One” double-coated tape with clear polyester carrier. Ideal for laminating plastic and nonwoven assemblies or devices to skin or to hold them on OR surfaces like stainless steel without increased adhesion at removal even after several hours.
#1587 Gentle “2-in-One” Double Coated Polyester Tape (3 mil/0.08mm) 60# Liner Gamma, EtO, SteamAdhesive ~1.4 mil Synthetic Rubber Adhesive
Carrier 0.5 mil Clear Polyester film
Adhesive ~1 mil Acrylic Adhesive, not tackified
Liner 60# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Key Features Strong, aggressive double-coated tape with clear polyester carrier. Ideal for laminating complex assemblies and heavy coating weight conforms well on uneven surfaces including most plastics.
#1567 Double Coated Polyester Tape (5 mil/0.13mm) 60# Liner Gamma, EtO
Adhesive ~2 mil Synthetic Rubber
Carrier 0.92 mil Clear Polyester film
Adhesive ~2 mil Synthetic Rubber
Liner 60# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 20137
Key Features The specially formulated adhesive makes this our gentlest tape for stick-to-skin applications.
#9874 Double Coated Polyethylene Tape (4.9 mil/0.12mm) 60# Liner Gamma, EtO
Reported Uses Repeat skin contact applications, especially on elderly, infant or other fragile skin.
Adhesive 0.95 mil Hypoallergenic Acrylate
Carrier 3.0 mil Transparent Polyethylene film
Adhesive 0.95 mil Hypoallergenic Acrylate
Liner 60# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Key Features High tensile medical tape with excellent stick-to-skin properties. Less conformable than polyethylene tapes but can be sterilized using all typical methods.
#1513 Double Coated Polyester Tape (3.4 mil/0.09mm) 80# Liner Gamma, EtO, Steam
Adhesive 1.2 mil Hypoallergenic Acrylate
Carrier 0.92 mil Polyester Film
Adhesive 1.2 mil Hypoallergenic Acrylate
Liner 80# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 20138
Key Features Different adhesives on each side of this versatile tape make it the best choice for applications where adhesion to two different substrates is required. The synthetic rubber adhesive adheres very well to a wide variety of substrates, including treated drape fabrics and polyethylene. The acrylate adhesive adheres securely to skin, yet removes gently. The polyester carrier assures durability and high strength.
#1577 Two-in-One Double Coated Polyester Tape (3.6 mil/0.09mm) 60# Liner Gamma, EtO, Steam
Adhesive 1.4 mil Synthetic rubber
Carrier 0.92 mil Clear Polyester film
Adhesive 1.0 mil Acrylic Adhesive
Liner 60# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Key Features Synthetic rubber adhesive on both sides provides aggressive holding power on a wide variety of substrates. Durable, strong and withstands all common sterilization techniques. Also approved for skin adhesion, especially for situations where other tapes might not adhere well enough.
#9877 High Performance Double Coated Polyester Tape (4.5 mil/0.11mm) 62# Liner Gamma, EtO, SteamAdhesive 1.75 mil Synthetic rubber
Carrier 0.92 mil Clear Polyester film
Adhesive 1.75 mil Synthetic rubber
Liner 62# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Note: Some polyethylene surfaces may not be compatible with this tape.
Version 8.1 August 20139
Key Features Liquid barrier, high coating weight differential tape provided on a two side release paper liner. Suitable for device construction, etc.
#1597 2-in-One Differential Polyester Tape (4.3 mil/0.11mm) 60# White Paper Carrier Gamma, EtO
Adhesive 1.7 mil Hi-tack Synthetic Rubber Adhesive
Backing 0.92 mil Polyester film
Adhesive 1.7 mil tackified Acrylic Adhesive
Carrier 60# White Paper, two sided silicone release
Wind Orientation — Paper Carrier Outside
Key Features Thin and very conformable. Very aggressive and will adhere well to a wide variety of materials. Can be sterilized using all common techniques.
#1524 Polyester Fiber Filled Transfer Adhesive (2.5 mil/0.06mm) 54# Liner Gamma, EtO, Steam
Adhesive 2.5 mil Polyester fiber-filled Hypoallergenic Acrylate
Liner 54# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 201310
Key Features Conformable, soft, cushioning apertured nonwoven cloth carrier double coated tape. Ideal for laminating in complex part assembly.
#9917 Double-Coated Spunlace Nonwoven Tape (12 mil/0.30mm) 62# Liner Gamma, EtO
Adhesive Hypoallergenic Acrylate
Carrier White spunlace polyester/rayon blend, 1.2 oz.
Adhesive Hypoallergenic Acrylate
Liner 62# bleached Kraft, two sided silicone release
Wind Orientation — Liner Outside
Key Features Highly aggressive and will adhere well to a wide variety of materials.
#1504XL Hi-Tack Transfer Adhesive (4.0 mil/0.11mm) 62# Liner Gamma, EtO
Adhesive 4.0 mil Hi-Tack Synthetic Rubber-based Adhesive
Liner 62# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 201311
Key Features Thin and very conformable. Aggressive and will adhere well to a wide variety of materials. May be sterilized with all common sterilization techniques. Premium weight liner for easier handling of die cut parts.
#1524A Polyester Fiber Filled Transfer Adhesive (2.5 mil/0.06mm) 78# Liner Gamma, EtO, SteamAdhesive 2.5 mil Polyester Fiber-filled Hypoallergenic Acrylate
Liner 78# bleached Kraft, two sided silicone
Wind Orientation — Liner Outside
Version 8.1 August 201312
Medical Single Coated Film Tapes Selection Guide — Polyethylene
Table Revised July 2011
Polyethylene
Properties1 1503 1521 1523 1525L 1526 9865 9865A
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) G*, E G*, E G*, E G*, E G*, E G*, E G*, E
2. Hypoallergenic Yes Yes Yes Yes Yes Yes Yes
3. Repeat/Chronic Skin Contact No Yes No Yes No Yes Yes
4. Conformable (L=Low; M=Medium; H=High) M M M M M M M
5. Fluid Resistance Yes Yes Yes Yes Yes Yes Yes
6. Color Tan Trans Blush Tan Trans Trans Trans Trans
7. Printable Backing Yes Yes Yes Yes Yes Yes Yes
8. Printable Liner Yes Yes Yes Yes Yes Yes Yes
9. Heat Sealable Yes Yes Yes Yes Yes Yes Yes
10. Tear by Hand No No No No No No No
11. MVTR gm/m2/24 hr None None None Very Low None Very Low Very Low
12. Porosity sec/100cc/in2 None None None None None None None
13. Minimum Tensilelbs/inch 5 8.0 5 5 5 5 5
Newtons/25mm 22.2 35.6 22.2 22.2 22.2 22.2 22.2
14. Elongation percentage 400 400 400 200 450 200 200
15. Typical Adhesion/ Stainless Steel
oz/inch 41 21 41 18 28 20 18
Newtons/25mm 11.4 5.8 11.4 5.0 7.8 5.6 5.0
16. Tape Calipermil 5 6.4 5 4.4 5 4.4 3.8
millimeters 0.13 0.16 0.13 0.11 0.13 0.11 0.10
17. Adhesive Calipermil 1.4 1.4 1.4 1.4 1.4 1.4 0.8
millimeters 0.04 0.04 0.04 0.04 0.03 0.04 0.02
18. Film Calipermil 3.6 5.0 3.6 3.0 3.6 3.0 3.0
millimeters 0.09 0.13 0.09 0.08 0.09 0.08 0.08
19. Liner Calipermil 4.9 6 4.9 4.9 4.9 4.9 2.5
millimeters 0.12 0.15 0.12 0.12 0.12 0.12 0.06
20. Liner Weight lbs/ream 63 83 63 63 63 63 54
21. Maximum Liner Release
gm/inch 50 30 50 40 50 40 30
Newtons/25mm 0.49 0.29 0.49 0.39 0.49 0.39 0.39
22. Maximum Widthinches 48 48 48 48 48 48 48
centimeters 122 122 122 122 122 122 122
23. Maximum Lengthyards 500 360 500 500 500 1000 1250
meters 457 329 457 457 457 914 1143
24. Approx. Roll Diameterinches 15 15 15 15 15 21 19.5
centimeters 38 38 38 38 38 53 49.5
25. Shelf Life years 2 2 2 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application . 2 Recommended suitability based on the processability of product through typical sterilization conditions .
* Reduced adhesion levels and increased liner release may occur after gamma irradiation .
Version 8.1 August 2013 13
Medical Single Coated Film Tapes Selection Guide — Polyolefin Blends
Polyolefin
Properties1 1527 1527LX 1527ENP 9835
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) G*, E G*, E G*, E G*, E
2. Hypoallergenic Yes Yes Yes Yes
3. Repeat/Chronic Skin Contact No No No Yes
4. Conformable (L=Low; M=Medium; H=High) M M M M
5. Fluid Resistance No No Yes Yes
6. Color Trans Trans Trans White
7. Printable Backing No No No No
8. Printable Liner N/A Yes Yes Yes
9. Heat Sealable Yes Yes Yes Yes
10. Tear by Hand Yes Yes No No
11. MVTR gm/m2/24 hr 6200 ~120 Very Low Very Low
12. Porosity sec/100cc/in2 <1 Very Low None None
13. Minimum Tensilelbs/inch 3 3 3 6.6
Newtons/25mm 13.3 13.3 13.3 29.4
14. Elongation percentage 50 70 50 300
15. Typical Adhesion/ Stainless Steel
oz/inch 25 40 25 26
Newtons/25mm 6.9 11.1 6.9 7.2
16. Tape Calipermil 6.8 7.4 7.4 5.5
millimeters 0.17 0.19 0.19 0.14
17. Adhesive Calipermil 1.8 1.8 1.8 1.5
millimeters 0.05 0.05 0.05 0.04
18. Film Calipermil 4.23 4.83 4.83 4.0
millimeters 0.113 0.123 0.123 0.10
19. Liner Calipermil N/A 6 4.9 6
millimeters N/A 0.15 0.12 0.15
20. Liner Weight lbs/ream N/A 83 63 83
21. Maximum Liner Releasegm/inch N/A 30 30 30
Newtons/25mm N/A 0.29 0.29 0.29
22. Maximum Widthinches 48 48 48 48
centimeters 122 122 122 122
23. Maximum Lengthyards 600 350 350 400
meters 549 320 320 366
24. Approx. Roll Diameterinches 14 14.6 14.6 15
centimeters 36 37 37 38
25. Shelf Life years 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only. It is the customer’s responsibility to determine the final suitability of our products for use in their application. 2 Recommended suitability based on the processability of product through typical sterilization conditions. 3 Pre-perforated film caliper.
* Reduced adhesion levels and increased liner release may occur after gamma irradiation.
Table Revised October 2013
Version 8.1 August 201314
Sing
le C
oate
d Po
lyet
hyle
ne/P
olyo
lefin
Tap
es
1503
1521
1523
1525
L15
2698
6515
2715
27LX
1527
ENP
9835
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
Version 8.1 August 201315
Key Features Liquid barrier, matte finish, translucent, heat sealable. #1521 Polyethylene Tape (6.4 mil/0.16mm) 83# Liner Gamma, EtO
Backing 5.0 mil Polyethylene Film
Adhesive 1.4 mil Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Blush Tan color is ideal for applications where a less conspicuous tape is desired. Liquid barrier, matte finish, heat sealable, printable. Higher adhesion level.
#1523 Blush Tan Polyethylene Tape (5.0 mil/0.13mm) 63# Liner Gamma, EtO
Backing 3.6 mil Polyethylene Film
Adhesive 1.4 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201316
Key Features Warm tan version of #1523. Liquid barrier, matte finish, heat sealable, printable.
#1503 Tan Polyethylene (5.0 mil/0.13mm) 63# Liner Gamma, EtO
Backing 3.6 mil Tan Polyethylene Film
Adhesive 1.4 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone
Wind Orientation — Backing Outside
Key Features Liquid barrier, matte finish, translucent, heat sealable. More conformable than #1521.
#1525L Polyethylene Tape (4.4 mil/0.11mm) 63# Liner Gamma, EtO
Backing 3.0 mil Polyethylene Film
Adhesive 1.4 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201317
Key Features Surface treated for improved printing. Liquid barrier, matte finish, translucent, heat sealable. Higher adhesion.
#1526 Polyethylene Tape (5.0 mil/0.13mm) 63# Liner Gamma, EtO
Backing 3.6 mil Polyethylene Film
Adhesive 1.4 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Surface treated polyethylene film for improved printing. Liquid barrier, matte finish, translucent, heat sealable.
#9865 Polyethylene Tape (4.4 mil/0.11mm) 63# Liner Gamma, EtO
Backing 3.0 mil Polyethylene Film
Adhesive 1.4 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201318
Key Features Surface treated polyethylene film for improved printing. Lighter weight liner and lower adhesion than #9865. Liquid barrier, matte finish, translucent, heat sealable.
#9865A Polyethylene Tape (3.8 mil/0.10mm) 54# Liner Gamma, EtOBacking 3.0 mil Polyethylene Film
Adhesive 0.8 mil Hypoallergenic Acrylate
Liner 54# bleached Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Breathable, transparent film tape, easy to tear in both machine and cross directions. Conformable.
#1527 Embossed Perforated Polyethylene/EVA Tape (7.4 mil/0.17mm) No Liner Gamma, EtO
Backing 4.5 mil Perforated PE/EVA Film
Adhesive 1.8 mil Hypoallergenic Tackified Acrylic
Self Wound — No Liner
Version 8.1 August 201319
Key Features Transparent, semi-breathable tape. Conformable and hand tears in both machine and cross directions. Provided on liner for easier handling and converting.
#1527LX Embossed Semi-perforated Polyethylene/EVA Tape (7.4 mil/0.17mm) 83# Liner Gamma, EtO
Backing 4.8 mil Semi-perforated PE/EVA Film
Adhesive 1.8 mil Hypoallergenic Tackified Acrylic
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Soft, conformable, and transparent non-breathable tape. Good for strapping applications, liquid barrier.
#1527ENP Embossed Polyethylene/EVA Tape (7.4 mil/0.17mm) 63# Liner Gamma, EtO
Backing 5.6 mil Embossed PE/EVA film
Adhesive 1.8 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201320
Key Features Opaque white, liquid barrier tape. #9835 White Polyethylene/ EVA Tape (5.5 mil/0.14mm) 83# Liner Gamma, EtO
Backing 4.0 mil EVA/Polyethylene Film
Adhesive 1.5 mil Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201321
Medical Single Coated Film Tapes Selection Guide
Polyester Incise Films Polyurethane
Properties1 1516 9860 9952 9830 9948 9832F 9833 9834 9836
1. Sterilization2 (G=Gamma; E=Ethylene Oxide; S=Steam Autoclave) G*, E, S G*, E, S G*, E, S G*, E G*, E G*, E G*, E G*, E G*, E
2. Hypoallergenic Yes Yes Yes Yes Yes Yes Yes Yes Yes
3. Repeat Skin Contact No No No No Yes Yes Yes Yes Yes
4. Conformable (L=Low; M=Medium; H=High) L No No H H H H H H
5. Fluid Resistance Yes Yes Yes Yes Yes Yes Yes Yes Yes
6. Color Clear Trans Natural Trans Trans Trans Trans
Trans (9834)Pink (9834P)Blue (9834B)Tan (9834T)
Trans
7. Printable Backing No Yes Yes No Yes Yes Yes Yes Yes
8. Printable Liner/Carrier N/A Yes Yes Yes Yes No No No No
9. Heat Sealable No No No Yes No No No No No
10. Tear by Hand No No No No No No No No No
11. MVTR gm/m2/24 hr None None None Low 400 1200 450 600 450
12. Porosity — Max sec/100cc/in2 None None None None None None None None None
13. Minimum Tensile, MDlbs/inch 20 TBD TBD 2.2 3.0 3.5 3.5 3.5 3.5
Newtons/25mm 89 TBD TBD 9.8 13.3 15.6 15.6 15.6 15.6
14. Elongation percentage 50 <50 <50 130 500 500 500 500 500
15. Typical Adhesion/ Stainless Steel
oz/inch 60 N/A N/A >26 19 N/A 14 15 14
Newtons/25mm 16.7 N/A N/A >7.2 5.3 N/A 3.9 4.2 3.9
16. Tape Calipermil 2.3 14.2 11.2 2.6 2.7 N/A 2.0 1.8 2.0
millimeters 0.06 0.36 0.28 0.07 0.07 N/A 0.05 0.05 0.05
17. Adhesive Calipermil 1.3 1.2 1.2 0.9 1.7 N/A 0.9 1.0 1.0
millimeters 0.03 0.03 0.03 0.02 0.04 N/A 0.02 0.03 0.03
18. Film Calipermil 1.0 13.0 10.0 1.7 1.0 0.8 1.1 0.8 1.0
millimeters 0.03 0.33 0.25 0.04 0.03 0.02 0.03 0.02 0.03
19. Liner/Carrier Calipermil N/A 4.9 4.9 4.6 4.9 5 5 5 5/2.5
millimeters N/A 0.12 0.12 0.12 0.12 0.13 0.13 0.13 0.13/0.06
20. Liner Weight lbs/ream N/A 63 63 63 63 78 78 78 78
21. Maximum Liner Releasegm/inch N/A 50 50 60 60 49 75 49 75
Newtons/25mm N/A 0.49 0.49 0.59 0.59 0.48 0.74 0.48 0.48
22. Maximum Widthinches 48 48 48 48 48 46 46 46 46
centimeters 122 122 122 122 122 117 117 117 117
23. Maximum Lengthyards 750 400 400 600 650 700 700 700 700
meters 686 366 366 549 594 640 640 640 640
24. Approx. Roll Diameterinches 9.5 19 17.5 14.5 15 11.5 14 14 14
centimeters 24 48 44.5 37 38 29.2 35.6 35.6 35.6
25. Shelf Life years 2 2 2 2 2 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application . 2 Recommended suitability based on the processability of product through typical sterilization conditions .
* Reduced adhesion levels and increased liner release may occur after gamma irradiation .
Table Revised November 2012
Version 8.1 August 2013 22
Sing
le C
oate
d Po
lyes
ter/
Inci
se/P
olyu
reth
ane
Film
Tap
es
1516
9830
9948
9834
9833
9836
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
T48
T168
Version 8.1 August 201323
Key Features Self wound clear polyester tape. High strength. #1516 Polyester Tape (2.3 mil/0.06mm) No Liner Gamma, EtO, Steam
Backing 1.0 mil Clear Polyester Film
Adhesive 1.3 mil Hypoallergenic Acrylate
Self Wound — No Liner
Key Features Rigid, non-conforming matte finish translucent polyester tape. #9860 Polyester Tape (14.2 mil/0.36mm) 63# Liner Gamma, EtO, Steam
Backing 13 mil Polyester Film
Adhesive 1.2 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201324
Key Features Matte finish polyethylene film incise tape. Thin and highly conformable.
#9830 Polyethylene Incise Tape (2.6 mil/0.07mm) 63# Liner Gamma, EtO
Backing 1.7 mil Polyethylene Film
Adhesive 0.9 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Rigid, non-conforming, natural, semi-opaque polyester tape. #9952 Polyester Tape (11.2 mil/0.28mm) 63# Liner Gamma, EtO, Steam
Backing 10 mil Polyester Film
Adhesive 1.2 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201325
Key Features Breathable, highly conformable incise tape. #9948 Conformable Breathable Incise Tape (2.7 mil/0.07mm) 63# Liner Gamma, EtO
Backing 1.0 mil Breathable Plastic Film
Adhesive 1.7 mil Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Liquid barrier, breathable, thin, conformable tape provided on a white paper carrier for premium appearance and handling. Suitable for wound care dressings, etc.
#9834 — Translucent#9834P — Pink#9834B — Blue#9834T — TanPolyurethane TapeOn Carrier(1.8 mil/0.05mm) 78# White Paper Carrier (on film side)Gamma, EtO
Adhesive 1.0 mil Hypoallergenic Acrylic Adhesive
Backing 0.8 mil Polyurethane Film
Carrier 78# White Paper, one side silicone release
Wind Orientation — Paper Carrier Outside
Version 8.1 August 201326
Key Features Liquid barrier, breathable, thin, conformable tape provided on a white paper liner as well as a clear poly carrier for premium appearance and handling. Suitable for wound care dressings, etc.
#9836Polyurethane TapeOn Poly Carrier with Liner(1.8 mil/0.05mm) 78# White Paper Liner (on adhesive side)Gamma, EtO
Liner 78# White Paper, one side silicone
Adhesive 1.0 mil Hypoallergenic Acrylic Adhesive
Backing 0.8 mil Polyurethane Film
Carrier Clear Poly Carrier
Wind Orientation — Poly Carrier Outside
Key Features Wound dressing film that is breathable yet provides a liquid barrier. Provided on a paper release carrier for ease of converting and handling, allowing a user friendly delivery system.
#9832F Polyurethane Film (0.8 mil/0.02mm) 78# White Paper Carrier Gamma, EtOBacking 0.8 mil Polyurethane Film
Carrier 78# white paper, two sided silicone release
Wind Orientation — Carrier Outside
Version 8.1 August 201327
Key Features Wound care version of #9832W. Liquid barrier, breathable, thin, conformable tape provided on a white carrier for premium appearance. Carrier has similar release and converting properties to #9832W.
#9833 Polyurethane Tape (2.0 mil/0.05mm) 78# White Paper Carrier Gamma, EtO
Adhesive 0.9 mil Hypoallergenic Acrylate
Backing 1.1 mil Polyurethane Film
Carrier 78# white paper, one side silicone
Wind Orientation — Carrier Outside
Version 8.1 August 201328
Rayon Nonwoven Tapes
Properties1 1529 1530 1530L 1533 1533L 1785
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) G*, E G*, E G*, E G*, E G*, E G*, E
2. Hypoallergenic Yes Yes Yes Yes Yes Yes
3. Repeat Skin Contact Yes Yes Yes Yes Yes Yes
4. Conformable (L=Low; M=Medium; H=High) M M M M M M
5. Fluid Resistance No No No No No No
6. Color White White White Tan Tan White
7. Printable Backing Yes Yes** Yes** Yes** Yes** Yes
8. Printable Liner Yes N/A Yes N/A Yes Yes
9. Heat Sealable No No No No No Yes
10. Tear by Hand Yes Yes Yes Yes Yes Yes
11. MVTR gm/m2/24 hr 4200 4200 4200 4200 4200 1200
12. Maximum Porosity sec/100cc/in2 50 150 50 150 150 50
13. Minimum Tensile, MD/CD
lbs/inch 5/2 5/2 5/2 5/2 5/2 5/2
Newtons/25mm 22.2/8.9 22.2/8.9 22.2/8.9 22.2/8.9 22.2/8.9 22.2/8.9
14. Elongation percentage 21 21 21 21 21 25
15. Typical Adhesion to Glass
oz/inch 17 14 17 14 14 24
Newtons/25mm 4.7 3.9 4.7 3.9 3.9 6.7
16. Tape Caliper without Liner
mil 5.5 5.5 5.5 5.5 5.5 5.5
millimeters 0.14 0.14 0.14 0.14 0.14 0.14
17. Liner Calipermil 6 N/A 4.6 N/A 4.6 6
millimeters 0.15 N/A 0.12 N/A 0.12 0.15
18. Liner Weight lbs/ream 83 N/A 63 N/A 63 83
19. Typical Liner Releasegm/inch 50 N/A 55 N/A 55 65
Newtons/25mm 0.49 N/A 0.54 N/A 0.54 0.64
20. Maximum Widthinches 48 48 48 48 48 48
centimeters 122 122 122 122 122 122
21. Maximum Lengthyards 500 850 650 850 450 450
meters 457 777 594 777 411 411
22. Approx. Roll Diameterinches 17 15 17 15 17 17
centimeters 43 38 43 38 43 43
23. Shelf Life years 2 3 3 3 3 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application . 2 Recommended suitability based on the processability of product through typical sterilization conditions .
*Reduced adhesion levels and increased liner release may occur after gamma irradiation . It is the customer’s responsibility to determine the final suitability of our products for use in their application .**Printing may require special types of ink and/or equipment .
Medical Nonwoven Tapes Selection Guide — Rayon
Table Revised July 2011
Version 8.1 August 2013 29
Rayo
n No
nwov
en T
apes
1529
1530
1530
L15
33/1
533L
1785
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
Version 8.1 August 201330
Key Features Gentle, breathable, conformable, printable. Heavier weight liner allows ease of converting and eliminates need for liner swapping.
#1529 Microporous Rayon Nonwoven Tape (5.5 mil/0.14mm) 83# Liner Gamma, EtO
Backing White rayon nonwoven, Acrylate binder
Adhesive Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Gentle, breathable, conformable tape. #1530 Microporous Rayon Nonwoven Tape (5.5 mil/0.14mm) No Liner Gamma, EtO
Backing White rayon nonwoven, Acrylate binder
Adhesive Hypoallergenic Acrylate
Self Wound — No Liner
Version 8.1 August 201331
Key Features Gentle, breathable, conformable tape provided on liner for ease of converting.
#1530L Microporous Rayon Nonwoven Tape (5.5 mil/0.14mm) 63# Liner Gamma, EtO
Backing White rayon nonwoven, Acrylate binder
Adhesive Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Tan color is ideal for consumer application where less conspicuous tape is desired. Gentle, breathable, conformable tape.
#1533 Tan Microporous Rayon Nonwoven Tape (5.5 mil/0.14mm) No Liner Gamma, EtO
Backing Tan rayon nonwoven, Acrylate binder
Adhesive Hypoallergenic Acrylate
Self Wound — No Liner
Version 8.1 August 201332
Key Features Tan color is ideal for consumer application where less conspicuous tape is desired. Gentle, breathable, conformable tape provided on liner for ease of converting.
#1533L Tan Microporous Rayon Nonwoven Tape (5.5 mil/0.14mm) 63# Liner Gamma, EtO
Backing Tan rayon nonwoven, Acrylate binder
Adhesive Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Nonwoven tape that is heat sealable to polyethylene and co-polymer films. Breathable tape that is acceptable for repeat skin contact.
#1785 Heat Sealable Microporous Nonwoven Tape (5.5 mil/0.14mm) 83# Liner Gamma, EtO
Backing Rayon NW, Acrylate binder and heat seal
Adhesive Hypoallergenic Acrylate
Liner 83# polycoated Kraft, silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201333
Polyester PET Blend
Properties1 1776† 9916 9917**
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) G*, E G*, E G*, E
2. Hypoallergenic Yes Yes Yes
3. Repeat Skin Contact Yes Yes Yes
4. Conformable (L=Low; M=Medium; H=High) H H H
5. Fluid Resistance No No No
6. Color White Tan White
7. Printable Backing Yes Yes N/A
8. Printable Liner Yes Yes No
9. Heat Sealable No No No
10. Tear by Hand No No No
11. MVTR gm/m2/24 hr 1300 1100 600
12. Typical Porosity sec/100cc/in2 6.5 7.2 36
13. Typical Tensile, MD/CDlbs/inch 11/5 30/15 14.6/3.3
Newtons/25mm 49.8/22.2 133.5/67 65/15
14. Typical Adhesion/ Stainless Steel
oz/inch 25 30 29.4/6.7
Newtons/25mm 6.9 8.3 8.2 /1.9
15. Tape Caliper without Liner
mil 11.5 15 12
millimeters 0.3 0.4 0.3
16. Liner Calipermil 6 4.6 3.5
millimeters 0.15 0.12 0.09
17. Liner Weight lbs/ream 83 63 62
18. Typical Liner Releasegm/inch 55 Max 42 35
Newtons/25mm 0.54 0.41 0.34
19. Maximum Widthinches 48 46 48
centimeters 122 117 122
20. Maximum Lengthyards 300 200 275
meters 274 183 251
21. Approx. Roll Diameterinches 16 13.5 15.5
centimeters 41 34 39
22. Shelf Life years 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability based on the processability of product through typical sterilization conditions . * Reduced adhesion levels and increased liner release may occur after gamma irradiation . It is the customer’s responsibility to determine the final suitability of our products for use in
their application .**Double coated tape .
† Restricted for use as a component in certain product applications .
Medical Nonwoven & Woven Tapes Selection Guide — Polyester/Polyester Blends
Table Revised July 2011
Version 8.1 August 2013 34
Poly
este
r/Po
lyes
ter-
Rayo
n Bl
end
Nonw
oven
Tap
es
1776
9916
9917
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
Version 8.1 August 201335
Key Features 100% polyester, apertured nonwoven. Soft, conformable, high strength tape. Liner substantial enough for kiss-cut converting and for use as final product liner.
#1776 Spunlace Polyester Nonwoven Tape (11.5 mil/0.3mm) 83# Liner Gamma, EtO
Backing White Spunlace polyester nonwoven, 1.3 oz
Adhesive Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Opaque tan spunlace nonwoven tape is ideal for consumer applications where less conspicuous tape is desired. Thicker nonwoven provides enhanced cushioning. Gentle, breathable, conformable tape provided on liner for ease of converting.
#9916 Tan Spunlace Polyester Nonwoven Tape (15 mil/0.40mm) 63# Liner Gamma, EtOBacking Tan spunlace polyester nonwoven, 2.2 oz
Adhesive Hypoallergenic Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201336
Key Features Conformable, soft, cushioning apertured nonwoven cloth carrier double coated tape. Ideal for laminating in complex part assembly.
#9917 Double-Coated Spunlace Nonwoven Tape (12 mil/0.30mm) 62# Liner Gamma, EtO
Adhesive Hypoallergenic Acrylate
Carrier White spunlace polyester/rayon blend, 1.2 oz.
Adhesive Hypoallergenic Acrylate
Liner 62# bleached Kraft, two sided silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201337
Polyurethane Nonwovens Rayon Acetate Woven Fabric
Properties1 9904 9907T† 9907W† 9907HTW† 1538 1538L
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) E E E E G*, E G*, E
2. Hypoallergenic Yes Yes Yes Yes Yes Yes
3. Repeat Skin Contact No Yes Yes No Yes Yes
4. Conformable (L=Low; M=Medium; H=High) H H H H L L
5. Fluid Resistance No No No No No No
6. Color Tan Tan White White White White
7. Printable Backing Yes Yes Yes Yes No No
8. Printable Liner No Yes Yes No No No
9. Heat Sealable No Yes Yes Yes No No
10. Tear by hand No No No No Yes Yes
11. MVTR gm/m2/24 hr 500 8000 8000 500 400 400
12. Typical Porosity sec/100cc/in2 170 0.7 0.7 170 140 140
13. Typical Tensile, MD/CD
lbs/inch 3.0 2.8/1.6 2.8/1.6 2.8/1.6 30.1/17 30.1/17
Newtons/25mm 13.4 12.5/7.1 12.5/7.1 12.5/7.1 134/75.6 134/75.6
14. Elongation percentage 400 300 300 300 None None
15. Typical Adhesion/Stainless Steel
oz/inch 44 35 35 44 33 33
Newtons/25mm 12.2 9.7 9.7 12.2 9.2 9.2
16. Tape Caliper without Liner
mil 11 10 10 11 8 8
millimeters 0.28 0.25 0.25 0.28 0.20 0.20
17. Liner Calipermil 3.5 4.5 4.5 3.5 N/A 6
millimeters 0.09 0.11 0.11 0.09 N/A 0.15
18. Liner Weight lbs/ream 60 54 54 60 N/A 83
19. Maximum Liner Release
gm/inch 200 200 200 200 N/A 50
Newtons/25mm 1.96 1.96 1.96 1.96 N/A 0.49
20. Maximum Widthinches 50 50 50 50 48 48
centimeters 127 127 127 127 122 122
21. Maximum Lengthyards 250 410 410 500 500 350
meters 228 375 375 457 457 320
22. Approx. Roll Diameter
inches 12 16 16 16 14 15
centimeters 30.5 41 41 41 36 38
23. Shelf Life years 2 2 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability based on the processability of product through typical sterilization conditions .* Reduced adhesion levels and increased liner release may occur after gamma irradiation . It is the customer’s responsibility to determine the final suitability of our products for use in
their application .
† Restricted for use as a component in certain product applications .
Medical Nonwoven and Fabric Tapes Selection Guide — Polyurethane Nonwovens and Fabric Tape
Table Revised August 2013
Version 8.1 August 2013 38
Poly
uret
hane
Non
wov
ens
and
Fabr
ic T
ape
9904
/990
7HTW
9907
T/W
1538
1538
L
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
Version 8.1 August 201339
Key Features Highly breathable, conformable, elastic tape. Gentle adhesive. Available in Tan and White.
#9907T — Tan #9907W — White Elastic Nonwoven Tape (10 mil /0.25mm) 54# Liner EtO
Backing Elastic Polyurethane/Polyethylene NW
Adhesive Hypoallergenic Acrylate
Liner 54# bleached Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features High tack version of #9907. Elastic, conformable tape. Available in Tan.
#9904 — Tan Elastic Nonwoven Tape (11 mil/0.28mm) 60# Buff Kraft Liner EtO
Backing Elastic Polyurethane Nonwoven
Adhesive Hi-tack Acrylate Adhesive
Liner 60# buff Kraft, two sided silicone
Wind Orientation — Backing Outside
Version 8.1 August 201340
Key Features High tack version of #9907W. Elastic, conformable tape. Available in White.
#9907HTW — White Elastic Nonwoven Tape (11 mil/0.28mm) 60# Buff Kraft Liner EtO
Backing Elastic Polyurethane/Polyethylene NW
Adhesive Hi-tack Acrylate Adhesive
Liner 60# buff Kraft, two sided silicone
Wind Orientation — Backing Outside
Key Features High strength woven tape, easy to tear in two directions. #1538 Rayon Acetate Woven Tape (8.0 mil/0.20mm) No Liner Gamma, EtO
Backing Woven white rayon acetate
Adhesive Hypoallergenic Acrylate
Self Wound — No Liner
Version 8.1 August 201341
Key Features High strength, easy to tear in two directions. Provided on liner for converting ease and use as final product delivery liner.
#1538L Rayon Acetate Woven Tape (8.0 mil/0.20mm) 83# Liner Gamma, EtO
Backing Rayon acetate woven cloth
Adhesive Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201342
Polyethylene PVC
Properties1 1772 1773 1774 9776 9777L 9780 9781 9785
1. Cell Structure Closed Closed Closed Closed Closed Closed Closed Closed
2. Sterilization2 (G=Gamma; E=Ethylene Oxide) G*, E G*, E G*, E G*, E G*, E G*, E G*, E G*, E
3. Hypoallergenic Yes Yes Yes Yes Yes Yes Yes Yes
4. Repeat Skin Contact No Yes Yes Yes Yes Yes Yes Yes
5. Conformable (L=Low; M=Medium; H=High) L M H M M H H H
6. Fluid Resistance Yes Yes Yes Yes Yes Yes Yes Yes
7. Color White White Tan (1774T) White (1774W) Tan Ivory Blue Ivory Tan
8. Printable Backing Yes3 Yes3 Yes3 Yes3 Yes3 Yes3 Yes3 Yes3
9. Printable Liner Yes Yes Yes Yes Yes Yes Yes Yes
10. Heat Sealable Yes Yes Yes Yes Yes Yes Yes Yes
11. Tear by Hand Yes Yes Yes Yes Yes Yes Yes Yes
12. MVTR gm/m2/24 hr None None None None Very Low Very Low Very Low Very Low
13. Porosity sec/100cc/in2 None None None None None None None None
14. Minimum Tensile, MDlbs/inch 4 4 3 3.5 3.8 3.8 3.8 3.8
Newtons/25mm 17.8 17.8 13.3 15.6 16.9 16.9 16.9 16.9
15. Elongation, minimum percentage 220 220 300 250 150 150 150 150
16. Typical Adhesion/ Stainless Steel, minimum
oz/inch 69 to Cello 36 24 36 8 8 8 8
Newtons/25mm 19.2 10 6.7 10 2.2 (Min) 2.2 (Min) 2.2 (Min) 2.2 (Min)
17. Foam Calipermil 62.5 31.3 20 31.3 32 20 20 20
millimeters 1.6 0.8 0.5 0.8 0.8 0.5 0.5 0.5
18. Typical Tape Caliper without Liner
mil 65 34 22 34 34 22.5 22.5 22.5
millimeters 1.7 0.9 0.6 0.9 0.9 0.6 0.6 0.6
19. Liner Calipermil 6 6 4.6 5.5 4.0 4.0 4.0 4.0
millimeters 0.15 0.15 0.12 0.14 0.1 0.1 0.1 0.1
20. Liner Weight lbs/ream 83 83 63 72 65 65 65 65
21. Maximum Liner Releasegm/inch 85 85 85 60 35 35 35 35
Newtons/25mm 0.83 0.83 0.83 0.59 0.34 0.34 0.34 0.34
22. Maximum Widthinches 48 48 48 48 48 48 48 48
centimeters 122 122 122 122 122 122 122 122
23. Maximum Lengthyards 80 145 289 145 145 210 210 210
meters 73 132 264 132 132 192 192 192
24. Approx. Roll Diameterinches 16.5 16.6 16 16.2 17 16 16 16
centimeters 42 42 41 41 43 41 41 41
25. Shelf Life years 2 2 2 2 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability based on the processability of product through typical sterilization conditions .3 May require primer or other pre-treatment to improve ink adhesion for printing .*Reduced adhesion levels and increased liner release may occur after gamma irradiation
Medical Foam Tapes Selection Guide
Table Revised November 2012
Version 8.1 August 2013 43
Poly
ethy
lene
and
PVC
Foa
m T
apes
1772
1773
1774
9776
9777
L97
8097
8197
85
Relative Adhesion to Skin
Prod
uct N
umbe
r
T0 T4 T24
Version 8.1 August 201344
Key Features Cushioning, white polyethylene foam tape. High adhesion. #1772 White Polyethylene Foam Tape (65 mil/1.6mm) 83# Liner Gamma, EtO
Backing 62.5 mil (1/16 in.) White closed cell Polyethylene Foam
Adhesive Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Outside
Key Features Medium thickness, white polyethylene foam tape. #1773 White Polyethylene Foam Tape (34 mil/0.9mm) 83# Liner Gamma, EtO
Backing 31.3 mil (1/32 in) White closed cell Polyethylene Foam
Adhesive Hypoallergenic Acrylate
Liner 83# polycoated Kraft, one side silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201345
Key Features Thin polyethylene foam tape, provided in two colors. #1774T — Tan #1774W — White Polyethylene Foam Tapes (20 mil/0.6mm) 63# Liner Gamma, EtO
Backing 20 mil closed cell Polyethylene Foam
Adhesive Hypoallergenic Acrylate
Liner 63# polycoated Kraft, 1 side silicone release
Wind Orientation — Liner Outside
Key Features Medium thickness tan polyethylene foam. Tan color is ideal for applications where a less conspicuous tape is desired.
#9776 Tan Polyethylene Foam Tape (34 mil/0.9mm) 72# Liner Gamma, EtO
Backing 31.3 mil, (1/32 in.) Tan closed cell Polyethylene Foam
Adhesive Hypoallergenic Acrylate
Liner 72# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201346
Key Features Soft, conformable closed cell PVC foam tape. Thicker foam provides for enhanced cushioning.
#9777L Ivory, Polyvinyl Chloride Foam Tape (34 mil/0.9mm) 65# Liner Gamma, EtO
Backing 32 mil (1/32 in.) Ivory closed cell PVC Foam
Adhesive Hypoallergenic Acrylate
Liner 65# bleached Kraft, one side silicone release
Wind Orientation — Liner Outside
Key Features Thin, soft, conformable closed cell PVC foam tape. #9781 Ivory, Polyvinyl Chloride Foam Tape (22.5 mil/0.6mm) 65# Liner Gamma, EtO
Backing 20 mil Ivory closed cell PVC Foam
Adhesive Hypoallergenic Acrylate
Liner 65# bleached Kraft, one side silicone release
Wind Orientation — Liner Outside
Version 8.1 August 201347
Key Features Blue version of #9781. #9780 Blue PVC Foam (22.5 mil/0.6mm) 65# Liner Gamma, EtO
Backing 20 mil Blue Closed-cell PVC Foam
Adhesive Hypoallergenic Acrylate
Liner 65# bleached Kraft, one side silicone
Wind Orientation — Liner Outside
Key Features Tan version of #9781. #9785 Tan PVC Foam Tape (22.5 mil/0.6mm) 65# Liner Gamma, EtO
Backing 20 mil Tan Closed-cell PVC Foam
Adhesive Hypoallergenic Acrylate
Liner 65# bleached Kraft, one side silicone
Wind Orientation — Liner Outside
Version 8.1 August 201348
Specialty Films Selection Guide
Specialty Films
Properties1 9960 9962 9967
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) G G G, E
2. Hypoallergenic Yes
3. Printable Backing Yes Yes Yes
4. Fluid Resistance Yes Yes Yes
5. Heat Sealable No No Yes
6. Light Transmission percentage 90 92 N/A
7. Haze Level, maximum percentage 2.5 1.5 N/A
8. Color Clear Clear Transparent
9. Typical Tensile, MDlbs/inch 166 85 Minimum 15
Newtons/25mm 738 378 66.7
10. Elongation, minimum percentage 70 90 100
11. Film/Liner Calipermil 6.8 3.9 2.0
millimeters 0.17 0.10 0.05
12. Maximum Widthinches 49 49 52
centimeters 124.5 124.5 132
13. Maximum Lengthyards 1600 2600 1500
meters 1463 2377 1372
14. Approx. Roll Diameterinches 22 21 12.5
centimeters 56 53 32
15. Shelf Life months 14 14 24
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability is based on the processability of product through typical sterilization conditions . It is the customer’s responsibility to determine the final suitability of our
products for use in their application .
Table Revised August 2013
See Samples of 9962 and 9960 — Page 64 and 65
Version 8.1 August 201349
Key Features Clear polyester film with an EVA coating for heat sealing. #9967 Heat-Sealable Polyester Film (2.0 mil/0.05mm) Gamma, EtO
Film 0.5 mil Polyester Film
Coating 1.5 mil EVA Heat Seal Coating
Wind Orientation — Heat Seal Coating Inside
Version 8.1 August 201350
Hydrocolloid Tapes Hydrogel
Properties1 9943/9943J 9944 9945J 9880
1. Sterilization2 (G=Gamma; E=Ethylene Oxide; S=Steam Autoclave) G* G* G*
2. Hypoallergenic Yes Yes Yes Yes
3. Repeat Skin Contact Yes Yes Yes Yes
4. Printable Backing Yes Yes Yes N/A
5. Fluid Resistance Backing-YesAdhesive-No
Backing-YesAdhesive-No
Backing-YesAdhesive-No No
6. Conformable (L=Low; M=Medium; H=High) H M M H
7. Color Pale Gold Med. Gold Med. Gold Translucent
8. MVTR gm/m2/24 hrs 20 105 TBD N/A
9. Typical Tensile lbs/inch 10 11 6 N/A
10. Elongation percentage 539 654 210 N/A
11. Typical Adhesionoz/inch S. Steel
5S. Steel
12S. Steel
12Nylon Mesh
130 gms min.
Newtons/25mm 1.4 3.3 3.3 1.3 minimum
12. Tape Calipermil 19 26 29.5 18
millimeters 0.5 0.7 0.75 0.5
13. Liner Calipermil 4.5 4.5 4.5 2.0
millimeters 0.1 0.1 0.1 0.05
14. Liner Weight lbs/ream 80 80 80 Polyester Film
15. Maximum Liner Releasegm/inch 350 300 300 TBD
Newtons/25mm 3.4 2.9 2.9 TBD
16. Maximum Widthinches 9.25 (adh.)
10.25 (liner)9.25 (adh.)
10.25 (liner)9.25 (adh.)
10.25 (liner) 21.5
centimeters 23.5/26 23.5/26 23.5/26 54.6
17. Maximum Lengthyards 75/150 75 60 150
meters 68/137 68 55 137
18. Approx. Roll Diameterinches 13 15 15 12
centimeters 33 38 38 30.5
19. Shelf Life years 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability based on the processability of product through typical sterilization conditions .* Reduced adhesion levels and increased liner release may occur after gamma irradiation .
Hydrocolloid & Specialty Tapes Selection Guide
Table Revised November 2009
Version 8.1 August 201351
Key Features A gentle Hydrocolloid adhesive provided with a polyurethane tape carrier. Hydrocolloid adhesives are excellent for long term wear and for hydrating the skin.
#9943/9943J Thin HydrocolloidTape(19 mil/0.5 mm)80# LinerGamma
Backing 1.0 mil Polyurethane Film
Adhesive 18 mil absorbent Hydrocolloid
Liner 80# bleached Kraft, two sided silicone
Wind Orientation — Backing Outside
Key Features Tackified hydrocolloid adhesive for improved initial adhesion. Polyurethane tape carrier protects the adhesive from the environment during wear. Excellent for long term wear and hydrating the skin.
#9944Hydrocolloid Tape(26 mil/0.7 mm)80# LinerGamma
Backing 1.0 mil Polyurethane Film
Adhesive 25 mil absorbent tackified Hydrocolloid
Liner 80# bleached Kraft, two sided silicone
Wind Orientation — Backing Outside
Version 8.1 August 201352
Key Features Heat sealable and slightly thicker version of #9944 #9945J Heat SealableHydrocolloid Tape(29.5 mil/0.75mm)80# LinerGamma
Backing 1.7 mil Heat Sealable Polyethylene Film
Adhesive 27.8 mil absorbent tackified Hydrocolloid
Liner 80# bleached Kraft, two sided silicone
Wind Orientation — Backing Outside
Key Features Conductive synthetic polymer-based hydrogel for electrodes, etc. #9880Hydrogel Adhesive(18 mil/0.5mm)2 mil Polyester Film Liner
Adhesive 18 mil Synthetic-based Hydrogel Adhesive
Liner 2 mil Polyester Film, two sided silicone
Wind Orientation — Liner OutsideUse barrier packaging
Version 8.1 August 201353
Properties1 1361 9954 9955 99563 9968
1. Sterilization2,3 (G=Gamma; E=Ethylene Oxide; S=Steam Autoclave) G, E E only E only E, S G, E
2. Backing Type Bleached Kraft Paper Polyester Polypropylene Polyester Bleached
Kraft Paper
3. Release Type Silicone Fluorosilicone Fluoropolymer Fluoropolymer Silicone
4. Hypoallergenic Yes Yes Yes Yes Yes
5. Printability Yes Yes Yes Yes Yes
6. Fluid Resistance No Yes Yes Yes No
7. Heat Sealable No No No No No
8. Color White Clear Clear Clear White
9. Adhesive Compatibility
silicone No Yes Yes Yes No
acrylate Yes Yes Yes Yes Yes
synthetic rubber Yes Yes Yes Yes Yes
10. Minimum Tensile, MD/CDlbs/inch 33 MD 60 MD 65/90 60/70 20 MD
Newtons/25mm 147 MD 267 290/400 270/315 89 MD
11. Film/Liner Calipermil 6.0 2.0 3.5 2.9 4.6
millimeters 0.15 0.05 0.09 0.07 0.12
12. Liner Weight lbs/ream 83 N/A N/A N/A 63
13. Maximum Widthinches 48 26 40 45 48
centimeters 122 66 101 114 122
14. Maximum Lengthyards 750 6000 1900 2400 900
meters 686 5486 1737 2195 830
15. Approx. Roll Diameterinches 15 18 18.5 18.5 15
centimeters 38 46 47 47 38
16. Shelf Life years 1 1 1 2 1
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability based on the processability of product through typical sterilization conditions . It is the customer’s responsibility to determine the final suitability of our
products for use in their application .3 Not suitable for E-Beam Treatment .
Release Liners Selection Guide
Table Revised November 2012
Version 8.1 August 201354
Key Features Hybrid silicone/fluoropolymer release coating is suitable for all adhesives. Release is coated on one side of a clear polyester film.
#9954 Fluorosilicone PolyesterRelease LinerSterilizable: ETO only(2.0 mil/0.05mm)
Lining 2.0 mil Polyester Film
Coating Fluorosilicone Release Coating
Wind Orientation — Release Coating Inside
Key Features 3M proprietary release coating is suitable for all adhesives. Coated on a clear polypropylene film.
#9955 Fluoropolymer PolypropyleneRelease LinerSterilizable: ETO only(3.5 mil/0.09mm)
Lining 3.5 mil Polypropylene Film
Coating Fluoropolymer Release Coating
Wind Orientation — Release Coating Inside
Version 8.1 August 201355
Key Features Bleached paper release liner, one side polyethylene coated and silicone over-coated. Printable.
#1361 83# Silicone Release Paper Liner (6.0 mil/0.15mm) 83# Paper Liner Gamma, EtO
Backing Bleached Paper
Barrier Polyethylene Barrier Coating
Coating Silicone Release Coating
Wind Orientation — Silicone Inside
Key Features Unique 3M fluoropolymer release coating on a clear polyester film. #9956 Fluoropolymer Polyester Release Liner (2.9 mil/0.07mm)Polyester Film Liner EtO, Steam
Film 2.9 mil Clear Polyester Film
Coating Fluoropolymer Release Coating
Wind Orientation — Release Coating Inside
Version 8.1 August 201356
Key Features Bleached paper release liner, one side polyethylene coated and silicone over-coated. Printable.
#9968 63# Silicone Release Paper Liner (4.6 mil/0.12mm) 63# Polycoated Paper Liner Gamma, EtO
Backing Bleached Kraft Paper
Barrier Polyethylene Barrier Coating
Liner Silicone Release Coating, one side
Wind Orientation — Silicone Inside
Version 8.1 August 201357
Low Profile Fasteners/ClosuresPlain Back, No Adhesive With Adhesive
Properties 7330 7334 7331 7335 7337 7336
1. Closure Type Loop Hook Loop Hook Loop Hook
2. Sterilization G, E E G, E E G, E E
3. Color White White White White White White
4. Heat Sealable Yes Yes N/A N/A N/A N/A
5. Dynamic Shear Closure 0 .5 inch2/3 .25mm2 290 oz (8.3kg) 290 oz (8.3kg) 290 oz (8.3kg) 290 oz (8.3kg) 290 oz (8.3kg) 290 oz (8.3kg)
6. 135 deg Peel Closure 12.5 oz/inch wide (360g/25mm wide)
12.5 oz/inch wide (360g/25mm wide)
12.5 oz/inch wide (360g/25mm wide)
7. Closure Calipermil 9.8 18.5 14 22.7 10 19.0
millimeters 0.25 0.5 0.4 0.6 0.25 0.5
8. Adhesive Description N/A N/A High Tack, Syn. Rubber-Based
High Tack, Syn. Rubber-Based
High Tack, Syn. Rubber-Based
High Tack, Syn. Rubber-Based
9. Adhesion tooz/inch N/A N/A 36 (LDPE) 36 (LDPE) 90 (S.Steel) 80 (S.Steel)
kg/25mm N/A N/A 1.0 (LDPE) 1.0 (LDPE) 2.6 (S.Steel) 2.3 (S.Steel)
10. Release Liner Caliper
mil N/A N/A 3.2 3.2 3.5 3.5
millimeters N/A N/A 0.08 0.08 0.09 0.09
11. Widthinches 0.5 – 30 0.5 – 28 0.5 – 28 0.5 – 26 0.5 – 28 0.5 – 26
centimeters 1.3 – 76 1.3 – 71 1.3 – 71 1.3 – 66 1.3 – 71 1.3 – 66
12. Length
yards< 1 .5" 175 150 150 150 150 150
> 1 .5" 450 250 145 145 145 145
meters< 3 .8cm 160 137 137 137 137 137
> 3 .8cm 411.5 228.6 132 132 132 132
13. Approx. Roll Diameter
inches< 1 .5" 10 10 10 10 10 10
> 1 .5" 15 15 15 15 15 15
centimeters< 3 .8cm 25 25 25 25 25 25
> 3 .8cm 38 38 38 38 38 38
Products 7334 and 7335 may not be gamma-stable at all customers’ levels of exposure (see page 69A) . Customers will need to evaluate their device construction requirements using the replacement . Please contact the 3M Center Medical Specialties group for more information and samples .
Fasteners, Closures & Components Product Selection Guide
Tube & Cord Organizer
Product Number ColorWidth
in. (cm)Total Length
in. (cm)Organizers/
CartonTypical Adhesion to Stainless Steel
oz (kg)
1115NS White 1.5 (3.8) 5.25 (13.3) 500 60 (1.7)
This is a tape-based recloseable organizer for use on surgical gowns and drapes or equipment . The product is supplied in bulk packaging, can be EtO sterilized for use in the operating room and included in procedure kits and packs .
Table Revised November 2012
Version 8.1 August 201358
#9812N, Neoprene Sheath (Finger Cot), 1" x 3-1/2" with 2-1/2" Flange (2.54cm x 8.9cm with 6.35cm Flange)Each part is intended for use as a surgical drape component and can be gamma or EtO sterilized. It consists of 11 mil thick
neoprene rubber (free of natural rubber or natural latex) molded in the shape of a tubular sheath with a collar flange. 2,000 parts
per box, bulk packed. Minimum order: 4,000 parts.
#7330, Gamma-Stable Loop Fastener3M #7330 is a low profile, gamma-stable loop with a nylon closure surface laminated to a polyethylene base film for stability. It is
designed for disposable medical and diagnostic applications requiring a limited number of adjustments such as surgical drape and
gown closures, tube and cable holders, monitoring and diabetic care devices. The product is also EtO sterilization stable.
#7331, Gamma-Stable Loop Fastener with Adhesive3M #7331 is a gamma-stable nylon tricot fastener laminated to a high tack, synthetic rubber-based adhesive designed for medical
construction and stick-to-skin applications. The fastener tape is currently supplied on a poly-coated, two-side siliconized, paper
release liner with basis weight of 54 pounds. The product is also EtO sterilization stable.
#7334, Low Profile Hook FastenerThis is a low profile hook made with a white polyolefin blend. It is designed for disposable medical and diagnostic applications
requiring a limited number of adjustments such as surgical drape and gown closures, tube and cable holders, monitoring and
ostomy devices. The product is EtO stable and stable up to 45 kilograys of gamma radiation for sterilization.
#7335, Low Profile Hook Fastener with AdhesiveThis version is a low profile white polyolefin blend hook fastener backed with a high tack, synthetic rubber-based adhesive
designed for medical construction and stick-to-skin applications. The fastener tape is currently supplied on a poly-coated,
two-side siliconized, paper release liner with basis weight of 54 pounds in rolls. The product is EtO stable and stable up to
45 kilograys of gamma radiation for sterilization.
#7336, Low Profile Hook Fastener with High Adhesion AdhesiveThis version is a low profile white polyolefin blend hook fastener backed with a very high tack, synthetic rubber-based adhesive
designed for medical construction and stick-to-skin applications. The fastener tape is currently supplied on a one-side siliconized,
bleached Kraft paper release liner with basis weight of 63 pounds in rolls. The product is EtO stable and stable up to 45 kilograys
of gamma radiation for sterilization.
#7337, Gamma-Stable Loop Fastener with High Adhesion Adhesive3M #7337 is the same gamma-stable nylon tricot fastener coated with a very high tack, synthetic rubber-based adhesive designed
for medical construction and stick-to-skin applications. The fastener tape is currently supplied in rolls on a one-side siliconized,
bleached Kraft paper release liner with basis weight of 63 pounds. The product is also EtO sterilization stable.
Version 8.1 August 201359
Closures — Pre-cut Strips & Rolls Selection Guide
Flexform ClosuresProduct Number Color Width Minimum Length Maximum Length Wires per Strip Strips per Sheet
9823D Blue 11/16" (17.5mm) 5" (13cm) 48" (122cm) 8 5
9779W White 0.34" (8.7mm) N/A 350 yds. (320m) 2 roll
9779B Blue 0.34" (8.7mm) N/A 350 yds. (320m) 2 roll
#9823D, Flexform Wire Tape Strips, BlueEach part consists of eight wires, encased in blue plastic, with a pressure sensitive adhesive applied to the smooth side. The strips
are supplied as sheeted parts (5 strips/sheet) on clear polyester release liner.
#9779W, Flexform Tape Rolls, WhiteEach part consists of two wires, encased in white plastic, with a pressure sensitive adhesive applied to the smooth side. The tape is
wound with the paper liner wound on the inside of the roll.
#9779B, Flexform Tape Rolls, BlueEach part consists of two wires, encased in blue plastic, with a pressure sensitive adhesive applied to the smooth side. The tape is
wound with the paper liner wound on the inside of the roll.
Flexfoam Closures/Clips
Product Number Color Width Total Clip Length Adhesive LengthClips
per SheetMinimum
Order Quantity
9818B White 11/32" (8.7mm) 5.25" (133.4mm) 2.5" (63.5mm) 10 25M
9818D Tan 11/32" (8.7mm) 4.5" (115mm) 2.0" (50mm) 10 30M
9818G Tan 11/32" (8.7mm) 5.25" (133.4mm) 2.5" (63.5mm) 10 30M
9818J White 11/32" (8.7mm) 6.4" (162mm) 3.0" (76mm) 10 30M* For custom colors and lengths, contact your 3M Account Representative .
#9818X, Flexfoam Closures/Clips The individual part consists of soft polyethylene foam laminated to four wires encased in polyolefin. A portion of the foam
laminate is coated with a pressure sensitive adhesive protected by a release liner. The product is supplied as multiple clips or
closures as a sheet.
Version 8.1 August 201360
Properties1 9792R 9793R 9795R 9964 9965
1. Sterilization2,3 (G=Gamma; E=Ethylene Oxide) G, E, E-Beam E, E-Beam N/A G, E G, E
2. Backing Type Aluminum Polypropylene Polypropylene Polyester White Polyester
3. Printable Backing Yes No No Yes No
4. Fluid Resistance Yes Yes Yes Yes Yes
5. Conformable (L=Low; M=Medium; H=High) H M M M M
6. Color Silver Transparent Transparent Transparent White
7. Light Transmission percentage 0 > 90 > 90 90 Low
8. Haze Level percentage N/A < 10 < 10 < 2 N/A
9. Clarity percentage N/A > 80 > 90 > 95 N/A
10. Typical Tensile Strength, MD
lbs/inch 16 40 40 40 40
Newtons/25mm 71 178 178 178 178
11. Typical Elongation percentage 8 186 180 186 220
12. Typical Adhesion, Stainless Steel
oz/inch 41 25 35 min 15 min 10 min
Newtons/25mm 11.4 7.0 9.7 min 4.2 min 2.8 min
13. Tape or Product Calipermil 2.5 3.2 4.0 2.5 3.4
millimeters 0.06 0.08 0.10 0.06 0.09
14. Adhesive Calipermil 1.1 1.2 2.0 0.5 0.7 (both sides)
millimeters 0.03 0.03 0.05 0.01 0.02
15. Backing Calipermil 1.4 2.0 2.0 2.0 2.0
millimeters 0.04 0.05 0.05 0.05 0.05
16. Liner Calipermil 4.6 4.9 2.0 2.0 2.0 (both sides)
millimeters 0.12 0.12 0.05 0.05 0.05
17. Liner Weight lbs/ream 61 63 Polyester Film Polyester Film Polyester Film
18. Max Liner Release or Unwind
gm/inch 50 50 30 20 20
Newtons/25mm 0.49 0.49 0.3 0.2 0.2
19. Maximum Widthinches 42 48 48 48 48
centimeters 106.7 122 122 122 122
20. Maximum Lengthyards 500 500 7504 350 350
meters 457 457 6754 320 320
21. Maximum Roll Diameterinches 13.6 14 164 9.5 12
centimeters 34.5 35.5 40.64 24.1 30.5
22. Shelf Life3 years 2 2 2 2 2
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability based on the processability of product through typical sterilization conditions . Reduced adhesion levels and increased liner release may occur after
gamma irradiation .3 When stored in original packaging between 50–80°F (10–27°C) and 40–60% RH .4 Dimensions listed are for rolls without extended liner only . Please consult with your 3M Account Manager for further information on additional options .
Diagnostic Tapes & Films Selection Guide — Part 1
Table Revised November 2012
Version 8.1 August 2013 61
Diagnostic Tapes & Films Selection Guide — Part 2
Table Revised August 2013
Specialty Films
Properties1 9960 9962
1. Sterilization2 (G=Gamma; E=Ethylene Oxide) G G
2. Hypoallergenic
3. Printable Backing Yes Yes
4. Fluid Resistance Yes Yes
5. Heat Sealable No No
6. Light Transmission percentage 90 92
7. Haze Level, maximum percentage 2.5 1.5
8. Color Clear Clear
9. Typical Tensile, MDlbs/inch 166 85 Minimum
Newtons/25mm 738 378
10. Elongation, minimum percentage 70 90
11. Film/Liner Calipermil 6.8 3.9
millimeters 0.17 0.10
12. Maximum Widthinches 49 49
centimeters 124.5 124.5
13. Maximum Lengthyards 1600 2600
meters 1463 2377
14. Approx. Roll Diameterinches 22 21
centimeters 56 53
15. Shelf Life months 14 14
1 Properties listed are based on limited testing and for comparative purposes only . It is the customer’s responsibility to determine the final suitability of our products for use in their application .2 Recommended suitability is based on the processability of product through typical sterilization conditions . It is the customer’s responsibility to determine the final suitability of our
products for use in their application .
Version 8.1 August 201362
Key Features Pierceable aluminum tape, hydrophobic adhesive. Opaque background provides good contrast. Conforms to irregular surfaces resulting in excellent seal to device.
#9792R Aluminum Diagnostic Tape (2.5 mil/0.07mm) 61# Liner Gamma, EtO
Backing 1.4 mil Aluminum
Adhesive 1.1 mil Acrylate
Liner 61# brown Kraft, one side silicone release
Wind Orientation — Liner Inside
Key Features Clear polyolefin backing coated with a hydrophobic adhesive. Optically clear for easy read-through. Low autofluorescence for high light transmission. Hydrophobic adhesive resists clouding when exposed to moisture. Adheres to a wide range of substances.
#9793R Polyolefin Diagnostic Tape (3.2 mil/0.08mm) 63# Liner EtOBacking 2.0 mil Polyolefin Film
Adhesive 1.2 mil Acrylate
Liner 63# polycoated Kraft, one side silicone release
Wind Orientation — Liner Inside
Version 8.1 August 201363
Key Features Optically clear for read-through. Very low auto-fluorescence for high light transmission. Non tacky to skin and gloves for easy handling, yet adheres to a wide variety of substrates. Chemically inert over wide pH range.
#9795R Advanced Polyolefin Diagnostic Tape (4.0 mil/0.10mm) 2.0 mil Liner Sterilization TBD
Reported Uses Excellent results when used for diagnostic test strips and other bioanalytical devices.
Backing 2.0 mil Polyolefin Film
Adhesive 2.0 mil Silicone Acrylate
Liner 2.0 mil fluoro-silicone white Polyester film
Wind Orientation — Liner Inside
Key Features Reduced adhesive coating weight version of #9794R Clear Polyester Tape.
#9964 Clear Polyester Diagnostic Tape (2.5 mil/0.06mm) 2.0 mil Clear Film Liner Gamma, EtO
Backing 2.0 mil Clear Polyester Film
Adhesive 0.5 mil Acrylate Adhesive
Liner 2.0 mil Clear Polyester, one side silicone
Wind Orientation — Backing Outside
Version 8.1 August 201364
Key Features Double-coated white polyester tape for gaskets, channel formation and other assembly application with the same neutral acrylic adhesive used for our other tapes in this family of products. Clear version samples may also be available.
#9965 Double Coated White Polyester Diagnostic Tape (3.4 mil/0.1mm) 2 mil Clear Film Liners Gamma, EtOLiner 2.0 mil Clear Polyester, one side silicone
Adhesive 0.7 mil Acrylate Adhesive
Carrier 2.0 mil White Polyester Film
Adhesive 0.7 mil Acrylate Adhesive
Liner 2.0 mil Clear Polyester, one side silicone
Wind Orientation — Liner Outside
Key Features Optically clear and dimensionally stable film treated both sides with a 3M proprietary non-leaching hydrophilic coating.
#9962 Hydrophilic Polyester Film (3.9 mil/0.10mm) No Liner Gamma
Reported Uses Excellent lateral flow in bioanalytical devices and diagnostic test strips.
Coating Hydrophilic Treatment
Backing 3.9 mil Polyester Film
Coating Hydrophilic Treatment
Wind Orientation — Supplied in Rolls
Version 8.1 August 201365
Key Features Optically clear and dimensionally stable film treated both sides with a 3M proprietary non-leaching hydrophilic coating.
#9960 Hydrophilic Polyester Film (6.8 mil/0.17mm) No Liner Gamma
Reported Uses Provides excellent lateral flow in bioanalytical devices and diagnostic test strips.
Coating Hydrophilic Treatment
Backing 6.8 mil Polyester Film
Coating Hydrophilic Treatment
Wind Orientation — Provided in Rolls
Version 8.1 August 201366
Custom Options — Technical Reference & GuideAs a value added service to our customers, 3M Medical Specialties provides custom converting on our tape products to meet
customer needs. One service is converting the tape into widths and lengths specific to our customer’s requirements. We also can
provide slit liner (SL) and/or extended liner (EL) on many of our tape products.
NOTE: Please be aware that there may be some restrictions on maximum roll length of any product slit less than 1" (25.4mm)
wide due to roll stability during handling.
Slit Liners (SL) — Liner is “scored” (not cut through totally) or “slit” through to (but not through) the tape.
• Available on all products on a release liner except:
– Transfer Adhesives #1504, #1524 and #1524A
– Polyurethane Tapes & Film #9832F, #9833,
#9834 and #9836.
• Tolerance is +/- 1/16" (+/- 1.5mm)
• Standard maximum slit roll width is 24" (61cm)
and minimum slit width is 0.5" (1.27cm)
• Slit (or Score) must be a minimum of 1/8" (3mm)
from the roll edge
• Orders must include total number and location(s)
of slit(s) and distance from the left edge
Single-coated Tapes Double-coated Tapes
Extended Liners (EL) — Liner extends past the edge or edges of the adhesive.
• Available on all products with a release liner except:
– any foam tape
– Transfer Adhesives #1524 and #1524A
– Hydrogel Adhesive #9880
• All other products have an EL minimum width of
1/8" (3mm) and tolerance is +/- 1/16" (+/- 1.5mm)
• Standard maximum roll width is 24" (61cm)
and minimum slit width is 0.5" (1.27cm)
Single-coated Tapes Double-coated Tapes
Slit Liner
Slit Liner
Liner wound onthe inside ofthe roll
Liner wound onthe outside ofthe roll
Left Side
Left Side
Slit Liner
Slit Liner
Liner wound onthe inside ofthe roll
Liner wound onthe outside ofthe roll
Left Side
Left Side
Slit Liner
Slit Liner
Liner wound onthe inside ofthe roll
Liner wound onthe outside ofthe roll
Left Side
Left Side
Extended Liner
Liner wound onthe outside ofthe roll
Left Side
Left Side
Liner wound on the inside of the roll
Extended Liner
Extended Liner
Liner wound onthe outside ofthe roll
Left Side
Left Side
Liner wound on the inside of the roll
Extended Liner
Extended Liner
Liner wound onthe outside ofthe roll
Left Side
Left Side
Liner wound on the inside of the roll
Extended Liner
Slit Liner and Extended Liner Capabilities