EASY LIFT ERGONOMIC DRUM TRANSPORTER OPERATING INSTRUCTIONS

Model#: EL100 TO EL1000

1

EASY LIFT EQUIPMENT

ERGONOMIC DRUM TRANSPORTER MANUAL

INTRODUCTION

EasyLift ergonomic drum transporters utilize an automatic clamping mechanism for handling any

size steel, plastic, or fiber chimed drum. These models vary in capacity from 100 to 1,000 pounds.

The specification plate affixed to each unit provides the following information: model number, serial

number, unit weight, and lifting capacity.

This manual contains information to instruct you on the proper use and maintenance of your

EasyLift ergonomic drum transporter. This manual should be available to all operators that will use

the EasyLift. Follow the maintenance procedures carefully to ensure a safe and reliable service life.

Do not operate this equipment until you have read and understood these instructions.

COMISSIONING YOUR ERGONOMIC DRUM TRANSPORTER

1. Remove all packing materials, protective strapping, and wood shipping blocks, then remove the

machine from the shipping pallet or crate.

2. Perform a visual inspection for component damage, including checking for hydraulic oil leaks.

3. Check that the ergonomic step-down floor lock is working properly by depressing the small portion

of the brake pedal to release foot lock. To engage the foot lock, depress the large portion of the

pedal to contact the floor. If functioning properly the device should release and lock. Check that

the caster wheels are free of obstruction and functioning properly.

MODELS EQUIPPED WITH SCALE SYSTEMS

If your equipment has a scale system, the indicator has already been calibrated and tested before

leaving the factory. The indicator has been disconnected and packaged separately for safe travel.

Unpack the indicator from the box and mount it to the swing bar above the lift control using the

provided mounting bracket. After mounting, connect the indicator cable to the corresponding

indicator cable on the machine by screwing the male and female ends together. Standard scale

indicators have internal batteries. Intrinsically safe indicators have external batteries which require

mounting under the indicator and connecting the battery cable to the back of the indicator. Scale

indicators are provided with a separate set of instructions and are packaged with the indicator. Please

read the scale indicator operations manual for instructions of use.

Turn the indicator “ON” and ensure it reads zero before engaging a drum. Follow the instructions,

listed in the manual, for engaging the drum or roll. If handling drums containing liquids, it may take

up to one minute for the indicator to settle on a specific weight. Most scale

indicators are so to display the weight in increments of 0.1 lb. or 0.05 kg,

DAILY SAFETY INSPECTION

1. Perform a visual inspection, checking for any evident damage to the machine or any hydraulic oil

leakage from previous use. Check all hydraulic connections and look under the machine itself for

leaks.

2. Check to see the step-down floor lock is functioning properly and wheels are free of obstruction.

3. Perform a visual inspection, checking for loose or damaged springs and jaws in the clamping

mechanism

Do not operate your EasyLift if you notice any unsafe condition(s) that may have been

caused by an accident or malfunction from previous use. Immediately report any unsafe

conditions or issues with the equipment to your supervisor. Tag the machine properly to

keep others from using it until the issue has been corrected.

SAFETY PRACTICES

1. Do not lift loads that exceed the machines’ rated capacity.

2. For transport, lift the drum just high enough so the drum has only the necessary floor

clearance for travel. Do not transport or move a drum at heights greater than 6”/15cm above

floor height.

3. Keep hands or other objects clear of the lifting cylinder, clamping mechanism and mast and

mast chain during operation.

4. Do not use the machine on inclined floors having a slope of more than 5 degrees.

WARNINGS

WARNING: Do not lift or suspend loads over people. Stay clear of suspended loads.

WARNING: Do not attempt to operate the equipment beyond its rated capacity.

WARNING: Never move the machine when the load is at its maximum lifting height. Lower

the mast so the drum has only the necessary floor clearance.

WARNING: Keep hands and feet away from the pinch points such as; mast channel, lifting &

rotation chains, clamp and any other moving parts.

WARNING: Do not make alterations or modifications to the machine without authorization

from Easy Lift Equipment.

WARNING: Do not leave the machine outside in inclement weather for extended periods.

WARNING: Never press the small lowering pedal too hard. The pedal is pressure

sensitive allowing the drum to be lowered at a safe controller speed. Pressing the

lowering pedal too hard will cause the drum to lower too quickly causing possible

damage or injury.

WARNING: Never leave the machine unattended without applying the step-down floor

lock. Leaving the machine unsecured may allow it to move inadvertently and

cause property damage or personal injury.

WARNING: Never operate the machine on an inclined floor with a slope of more than 5

degrees.

EASYLIFT ERGONOMIC DRUM TRANSPORTER

OPERATING INSTRUCTIONS

TO ENGAGE AND TRANSPORT DRUMS:

1. Press down on the small lowering pedal of the lift cylinder so the clamp is fully lowered.

Center the clamping mechanism with the center of the drum and push the machine forward

until the clamping mechanism contacts the drum. The lower jaw of the clamping mechanism

needs to be slightly below the drums’ chime. If it is above the drums chime, refer to the

instructions below for adjusting the height of the clamping mechanism.

2. Push the larger lever of the lift cylinder to elevate the clamp allowing it to engage the

clamping mechanism onto the chime of the drum. Maintain a small amount of forward

pressure on the machine to keep the clamp tight against the drum to ensure the clamping

mechanism grips the drum chime securely. After the clamp is engaged continue pumping the

foot pedal until the drum is elevated slightly above floor level for safe travel. The pushed to

transport the drum.

3. Press the smaller release pedal to lower the clamping mechanism and drum until the upper

clamping jaw has retracted completely, disengaging the drum.

ADJUSTING CLAMPING MECHANISM FOR VARIOUS HEIGHT DRUMS:

MODELS WITH THE CLAMPING MECHANISM INSIDE THE MAST CHANNEL

1. Standard models required the operator to pump the lift pedal many times to fully elevate the

clamping mechanism without a load. There are two lower hole positions available to lower the

clamping mechanism to handle shorter height drums. The lowest position available will enable

the drum transporter to clamp drum as short as 26”/66 cm in overall height.

2. Remove the circle cotter pin & adjustment pin while holding the clamping mechanism with

your other hand. Lower the clamping mechanism to one of the lower hole positions

available. Then re-insert the adjustment pin & cotter pin into the desired location. Lower the

inner mast by fully depressing on smaller lowering pedal.

MODELS WITH THE CLAMPING MECHANISM OUTSIDE THE MAST CHANNEL

1. Remove the cotter & adjustment pin while holding the clamping mechanism with your other

hand. Lower the clamping mechanism into one of the six lower hole positions available so

that the lower jaw is slightly below the chime of the drum with the drum at floor level. Re-insert the adjustment & cotter pins into the desired hole position.

MODELS EQUIPPED WITH SCALE SYSTEMS

If your equipment has a scale system, the indicator has already been calibrated and tested before

leaving the factory. The indicator has been disconnected and packaged separately for safe travel.

Unpack the indicator from the box and mount it to the swing bar above the lift control using the

provided mounting bracket. After mounting, connect the indicator cable to the corresponding

indicator cable on the machine by screwing the male and female ends together. Standard scale

indicators have internal batteries. Intrinsically safe indicators have external batteries which require

mounting under the indicator and connecting the battery cable to the back of the indicator. Scale

indicators are provided with a separate set of instructions and are packaged with the indicator. Please

read the scale indicator operations manual for instructions of use.

Turn the indicator “ON” and ensure it reads zero before engaging a drum. Follow the instructions,

listed in the manual, for engaging the drum or roll. If handling drums containing liquids, it may take

up to one minute for the indicator to settle on a specific weight. Most scale indicators are so to

display the weight in increments of 0.1 lb. or 0.05 kg,

ERGONOMIC DRUM TRANSPORTERS WITH ADJUSTABLE LEG FEATURE

EasyLift Ergonomic Drum Transporters with capacities from 400 lb./181.5 kg. to 1000 lb./354.7 kg

are the same machine with the legs in different positions. Occasionally customers receive a new

product in drums which has a weight that exceeds the original ordered capacity of their EasyLift

Ergonomic Drum Transporter. Increasing or decreasing the capacity of these models is fast and

simple. Should the capacity on the transporter need to be increased, please contact us for instructions.

MAINTENANCE INSTRUCTIONS

1. Before every usage, check that all spring, pins, casters, lift chain and its anchors are in good working

order and the hydraulic jack works properly without leakage.

2. On a monthly basis, spray light grade oil on moving parts in the clamping mechanism to ensure

smooth operation. It is recommended to keep the clamping mechanism lubricated and free from

foreign materials which may impede proper operation of jaws and springs. The Darcor™ casters

equipped on this equipment have precision sealed ball bearings and require no lubrication.

3. For heavy usage, it is recommended to replace all springs, hydraulic oil and sealing components of

the hydraulic cylinder once each year.

EASYLIFT ERGONOMIC DRUM TRANSPORTER

MAINTENANCE CHECKLIST

Maintenance Intervals

1

Mo

6

Mo

12

Mo

3

Years

Structural

Steel:

1.1 Check for cracked welds on frame X

1.2 Check to verify that specification data plates

are affixed to the unit X

1.3 Grease mast rollers and check roller condition X

Clamping

Head(s):

2.1 Inspect heads for loose or missing pins, cotter

pins, springs, and replace as necessary X

2.2 Lubricate clamping mechanisms X

2.3 Replace all springs X

2.4 Replace all pins, and links X

Wheels:

3.1 Grease wheel swivel grease fittings X

3.2 Check wheels for excessive wear and proper

alignment X

Hydraulic

Cylinder: 4.1 Check cylinder for leaks and proper operation X

Chain: 5.1

Verify proper chain tension and inspect chain

for damage X

5.2 Lubricate chain X

The maintenance intervals refer to normal service conditions.

In high volume usage conditions, the intervals must be increased as required.

Do not allow the lower jaw to

make contact with the paper

portion of the fiber drum when

trying to elevate the drum.

EasyLift Ergonomic Drum Transporter with EG1

Single Clamping Mechanism for use on Fiber Drums

IMPORTANT NOTE FOR HANDLING FIBER DRUMS

IMPORTANT:

It is important that the lower jaw does not contact the paper portion of the drum when raising

the drum. Keep the lower jaw away from the paper portion of the drum until the lower jaw of

the clamping mechanism is high enough to contact the metal skirt below the locking band.

Then push the transporter forward to contact the skirt and continue to elevate the clamping

mechanism. If the lower jaw contacts the paper portion of the drum when elevating the drum,

the clamping mechanism will attempt to clamp the drum in this position and miss or tear the

skirt. If this is done incorrectly, lower the clamp and try again. The clamping mechanism can

also grip the drum without the lid and locking band.

Raise the clamping mechanism

until the lower jaw is just high

enough to contact the metal skirt

just below the locking band.

Then move the transporter forward so

the lower jaw contacts the metal skirt

under the drums locking band and

continue to elevate the drum upward.

EasyLift Ergomonic Drum Transporter with EG2L

Double Clamping Mechanism for use on Fiber

Drums

IMPORTANT NOTE FOR HANDLING FIBER DRUMS

When handling fiber drums it is necessary to engage the fiber drum guards prior

to attempting to grip fiber drums.

To engage the fiber drum guards, remove each pin on the top of each side of the

double clamping mechanism and pull the fiber drum guards forward. With the

fiber drum guards in a forward position, inset the pins back into the guards to

lock them in the forward position. The purpose of the fiber drum guards is to

keep the lower clamping jaws from contacting the paper side of the drum when

elevating the clamp against the drum. The lower clamping jaws will move under

the locking band o the drums lid when the clamp is elevated to the proper height.

When not handling fiber drums, remove the pins again, move the guards back to

the original position and re-inset the pins. .

69"

17

5 c m

16"

40

.6 c

m

42" /

106

.7 c

m

6" / 15.24 cm

Adjustable54

3/8

"13

8.1 1

cm

41.5

"10

5.4 3

[cm

]

44.5

"11

3.0 2

[cm

]

37.5" 95.19[ cm]36" 91.43[ cm]

34.5" 87.61[ cm]33" 83.80[ cm]

38.5

"97

.78

[cm

]

35.5

"90

.17

[cm

]

MODELS EL400 / EL600/ EL800 / EL1000CAPACITY: 400 to 1000 lb. / 181.5 kg to 454 kg.DRUM LIFT HEIGHT: 20" / 50.8 cmMACHINE WEIGHT: 350 lb. / 159 kg.

OPTIONAL CAPACITY UP TO: 1500 lb. / 680 kg.OPTIONAL DRUM LIFT HEIGHTS UP TO 72" / 189 cm

EASY LIFT EQUIPMENT2 MILL PARK CTNEWARK, DE 19713

Ergonomic Drum Transporter™ Maintenance Checklist

Maintenance Intervals

1

Mo

6

Mo

12

Mo

3

Yrs

Structural

Steel:

1.1 Check for cracked welds on frame X

1.2 Check to verify that specification data plates

are affixed to the unit X

1.3 Grease mast rollers and check roller condition X

Clamping

Head(s):

2.1 Inspect heads for loose or missing pins, cotter

pins, springs, and replace as necessary X

2.2 Lubricate clamping mechanisms X

2.3 Replace all springs X

2.4 Replace all pins, and links X

Wheels:

3.1 Grease wheel swivel grease fittings X

3.2 Check wheels for excessive wear and proper

alignment X

Hydraulic Cylinder: 4.1 Check cylinder for leaks and proper operation X

Chain: 5.1

Verify proper chain tension and inspect chain

for damage X

5.2 Lubricate chain X

**The maintenance intervals refer to normal service conditions. In case of aggravated conditions, the

intervals must be reduced/increased as required.

10

EASY LIFT EQUIPMENT WARRANTY POLICY

FOR MODELS WITH PREFIXES: ED/EL/ELDR/EG & RCR Easy Lift Equipment (“ELE”) warrants each new Drum Hauler™ & Roll Hauler product to be free from factory

material and workmanship defects, under normal use with proper maintenance, for a period of 12 months.

Warranty coverage for this warranty period is provided by authorized dealers and includes parts. Labor is covered

for the same periods of 12 months as outlined above. Please call ELE for the authorized repair dealer in your area.

ELE shall be the sole judge of the validity of any claim or defect and may elect to make any replacement or repair

of any part thereof that it has agreed to be defective. Wearable Items: Such as hoses, bearings, belts, brake discs,

brushes, seals, springs and wheels are wear items and not covered under warranty. ELE assumes no liability

whatsoever to work done, parts replaced, or expenses incurred not specifically authorized by it. Normal

maintenance or replacement of service items is not covered by this warranty. No warranty claims will be

considered to customers with any delinquent outstanding balance. When batteries, battery chargers, scale printers

or scale indicators are purchased from ELE with the equipment, the original manufacturer’s warranty applies.

WARRANTY LIMITATION/DISCLAIMERS:

Easy Lift Equipment reserves the right to void warranty coverage if the unit has been overloaded beyond capacity

limitation, damaged due to misuse or abuse, neglect, accidents, freight damage. improper repair, improper storage

or that have been modified or repaired in any manner not approved by ELE. Equipment used in abrasive or

corrosive conditions, in freezers or excessive moisture, must be properly equipped for the environment to assure

the warranty is not voided. Warranty service and claims should be directed to our customer service department

who will contact a local authorized dealer or other representative in your area or we will assist the customer in

locating a local service representative in their area. The warranty described here above shall constitute the sole

remedy of the dealer and/or the initial purchaser. ELE shall under no circumstances be liable for special, general

incidental or consequential damages. ELE neither assumes nor authorizes any person to assume for it any other

obligation or responsibility in connection with this product warranty. In no event shall ELE be responsible for

direct, indirect, special or consequential damages or any other delay or any economic or commercial loss resulting

from Easy Lift Equipment’s performance or non-performance under this warranty. This warranty is expressly in

lieu of all warranties, obligations or responsibilities of ELE dealers or other authorized source, expressed or

implied or statutory.

SUBMITTING CLAIMS:

To make a claim under this guarantee, please contact Easy Lift Equipment for consideration. We can be reached

by calling 800-233-1800 then press 4 for customer service or by writing to sales@easylifteqpt.com. Do not

return defective parts unless a return authorization (RA) has been provided requesting for return. Do not send

defective parts to ELE unless requested. If requested, we will provide shipping information on how the part

should be returned and bear the expense for the return, if the part is proven to be defective.

A copy of the work order made at the time of the repair and parts claimed under warranty may be requested for

ELE’s inspection.

ORDERING PARTS:

Easy Lift Equipment’s products are distributed through a our service department and generally always ship the

same day when ordered. Parts are also available from many authorized dealers in your area. You will be well

taken care of whenever parts, adjustments or repairs are needed. When contacting ELE, please be sure to state

model number and serial number for the equipment. There is no cost for replacement manuals, parts lists and

other generally information containing part numbers and nomenclature. Most manuals contain parts pricing but

may not be current as parts pricing can change. Any customer service representative can provide timely parts

quotations upon request. Adherence to above procedure will save time and provide speedy assistance when it

counts. You are of course always welcome to bring to us any questions, comments or recommendations pertaining

to your Easy Lift Equipment products.

11

MANUFACTURER CONTACT INFORMATION:

Easy Lift Equipment Co., Inc. Phone: 800-233-1800: 302-737-7000

2 Mill Park Ct. Fax: 302-737-7333

Newark, DE 19713 Website: www.easylifteqpt.com

Email: sales@easylifteqpt.com

Updated: 10/24/2017

12

8

12

19

20

22

1

33

27

28

29

26

31

30

36

399

38

37

40

6910

18

432

2324

34

14

35

35

7515

Bill Flowers

25

13

42, 4311

44

21

15a

17 16

32

41

EasyLift Drum Transporter Model EL100 to EL1000

13

9

10

8

45

3

112

1

6

7

EASYLIFT SCALE MAST PARTS

14

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 EG Please see Clamping Mechanism page 12 5/16-18 HN 0.50$ 5/16-18 Finished Hex Nut (zinc) 143 5/16 LW 0.10$ 5/16 Lock Washer (zinc) 144 5/16 FW 0.10$ 5/16 Flat Washer (zinc) 125 5/16-18 X 1 HHCS 0.30$ 5/16-18 x 1 Hex Head Cap Screw Grade 5 (zinc) 86 5/16-18 x 3/4 HHCS 0.25$ 5/16-18 x 3/4 Hex Head Cap Screw Grade 5 (zinc) 48 1/2-13 x 3 3/4 HHCS 2.00$ 1/2-13 x 3 3/4 Hex Head Cap Screw Grade 5 (zinc) 29 1/2 LW 0.10$ 1/2 Lock Washer (zinc) 4

10 1/2-13 HN 0.15$ 1/2-13 Finished Hex Nut (zinc) 411 5/16 FW 0.10$ 5/16 Flat Washer (zinc) 212 W-405-PSE 60.64$ 5" PSE Wheel Only 212 W-408-PSE 85.96$ 8" PSE Wheel Only 213 3530210 270.00$ EL Leg Set for 5" Casters at 400lb, 600lb or 800lb capacity 113 3530211 270.00$ EL Leg Set for 5" Casters at 600lb, 800lb or 1,000lb capacity 113 3530212 270.00$ EL Leg Set for 8" Casters at 400lb, 600lb or 800lb capacity 113 3530213 270.00$ EL Leg Set for 8" Casters at 600lb, 800lb or 1,000lb capacity 114 31-405-PSE 75.66$ 5" Swivel Caster with PSE Wheel 214 31-408B-PSE 150.00$ 8" Swivel Caster with PSE Wheel & Brake 215 16FL0580 55.00$ Step Down Floor Lock (for 5" wheels) 116 5/16-18 X 1 1/4 HHCS 0.35$ 5/16-18 x 1 1/4 Hex Head Cap Screw Grade 5 (zinc) 417 5/16-18 x 1 FSHCS-SS 0.40$ 5/16-18 x 1 Flat Socket Head Cap Screw (stainless steel) 218 3/8-16 x 1 1/2 SHCS 1.25$ 3/8-16 x 1 1/2 Socket Head Cap Screw Alloy Plated 219 8912 66.00$ Chain to Mast Bracket 120 3/8-16 HN 0.10$ 3/8-16 Finished Hex Nut (zinc) 221 3/8 LW 0.10$ 3/8 Lock Washer (zinc) 222 3912 110.00$ Regular Inner Mast 123 4008 32.00$ Delrin Roller 424 90295A187 0.25$ 1/16" Nylon Flat Washer 424 95606A170 0.25$ 1/32" Nylon Flat Washer 425 5516E 40.00$ Optional: Belt Cradle Kit (includes all hardware) 126 55061 56.00$ 4" Sheave Wheel 127 816 5.55$ Bronze Bushing 128 45061 27.00$ Sheave Wheel Axle (1" x 2.125") 129 45062 1.00$ Grease Fitting 130 7912-4-812 90.00$ Sheave Wheel Bracket 4" (.812" bore) 131 93445A425 0.75$ 1/4"-20 x 3/8" Stainless Steel Knurl-Grip Set Screw 232 3022 98.00$ 4" Sheave Wheel Cover 133 10-24 x 3/8 PTHS-SS 0.25$ 10-24 3/8 Phillips Truss Head Screw (stainless steel) 434 1726 17.25$ Ansi 60 Chain, 35.5" Length (20" lift models) 134 1726-SP 56.25$ Ansi 60 Chain, 35.5" Length (FDA 20" lift models) 135 60HMCL 2.00$ ANSI 60 Link 235 ARC060SCL1 4.00$ FDA ANSI 60 Link 236 2022 22.50$ Chain Adjuster for ANSI 60 Chain 137 1/2-13 HN 0.15$ 1/2-13 Finished Hex Nut (zinc) 238 1/2-13 x 1 1/2 HHCS 0.75$ 1/2-13 x 1 1/2 Hex Head Cap Screw Grade 5 (zinc) 239 35091 55.00$ Cylinder Clamp Bracket 140 MK2429-20 765.00$ Hydraulic Lift Cylinder 140 MK2429-25 775.00$ Hydraulic Lift Cylinder 141 65657 1.75$ Handle Grips 242 1" x 3" x 17-1/4" HRFB CW 27.50$ 1" x 3" x 17-1/4" HRFB Ergo Counter Weight 844 MCL007031 8.00$ Specification Plate 1

EASY LIFT ERGONOMIC DRUM TRANSPORTER EL100 to EL1000PARTS LIST

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 8/31/2017

15

16

ITEM PART NO. PRICE EACH DESCRIPTION1 HF500-6 159.65$ RAM - Specify travel2 K HF500-4 3.00$ Top Nut O-Ring3 HF500-3 39.25$ Top Nut 4 HF500-2 118.10$ Reservoir Tube - Specify Travel5 HF500-5 137.00$ Inside Cylinder Tube - Specify Travel6 HF500-8 6.20$ RAM Cup Support Washer7 HF500-8A Obsolete Turn Piston Over9 K HF500-7 15.60$ RAM Cup

10 K HF500-32 5.10$ Body O-Ring (2)11 HF500-9 3.25$ RAM Cup Washer12 QH525-13 4.20$ RAM Cup Nut13 HF500-30 4.90$ Filler Screw & Washer (2)15 HF500-23 41.15$ Foot Release Lever Assembly16 HF500-22 13.15$ Piston Lever Return Spring19 K HF500-15RP 32.50$ Release Plunger (including seals)20 K HF500-24RPSS 12.50$ Stainless Steel Release Lever Pin (including cotter pins)21 K HF500-25RP 8.60$ Lever Socket Pin (2) (including cotter pins)22 K HF500-29 10.75$ Pump Piston Clip27 HF500-1RP -$ Body Assembly - NOT AVAILABLE28 K HF500-51RP 15.50$ Pump Valve29 K HF500-50RP 27.00$ Release Valve30 HF500-53RP 142.00$ Hydraulic Repair Kit (all K items)30 HF500-53RP-SA 190.00$ Hydraulic Repair Kit (all K items) w/ SS & FDA applications31 K HF500-54RP 86.00$ Pump Piston Assembly (complete)31 K HF500-54RP-SA 130.00$ Pump Piston Assembly (complete) w/ SS & FDA applications32 HF500-44 65.00$ Lever Arm with Rubber33 HF500-43 32.60$ Socket34 K HF500-42RPSS 13.50$ Stainless Steel Lever Arm Pin (including cotter pins)

HF500-38 11.70$ Pump Piston ONLY

NOTE: RV model overload assembly parts are not available. Unit must be returned to factory for repair.

HF500 FOOT OPERATED HYDRAULIC CYLINDERPARTS LIST

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 9/8/2017

17

2

4

5

6

1

13

14 3, 17

7, 17

3, 177, 17

10

15

16

12

EASY LIFT EQUIPMENT INC.ERGO CLAMP MECHANISM - Part List

8

9

11

18

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 6302 165.00$ Housing (Black Powder Coating) 11 6302SS 290.00$ Housing (Stainless Steel) 12 9107 85.00$ Upper Jaw (Black Powder Coating) 12 9107SRJ 100.00$ Upper Jaw (Spark Resistant) 13 15104-1SS 14.50$ 3/8" x 2.242" Pin, Fibre Guard, Housing to Clevis (stainless steel) 24 7107 90.00$ Lower Jaw (Black Powder Coating) 14 7107SRJ 100.00$ Lower Jaw (Spark Resistant) 15 13009-1 13.50$ Link, Jaw to Jaw (zinc) 26 1470-6 2.00$ Custom Washer EG (zinc) 27 16104-1SS 13.50$ 3/8" x 1.770" Pin, Upper Jaw Link (stainless steel) 28 8002 35.00$ Adjustment Slide (Black Powder Coating) 28 8002Z 35.00$ Adjustment Slide (FDA Powder Coating) 28 8002SS 70.00$ Adjustment Slide (Stainless Steel) 29 5912 65.00$ Upper Clevis 8" (Black Powder Coating) 19 5912Z 65.00$ Upper Clevis 8" (FDA Powder Coated) 19 5912SS 90.00$ Upper Clevis 8" (Stainless Steel) 19 5912S 65.00$ Upper Clevis 6" (Black Powder Coating - Double Mast) 19 5912ZS 65.00$ Upper Clevis 6" (FDA Powder Coating - Double Mast) 19 5912SS-S 90.00$ Upper Clevis 6" (Stainless Steel - Double Mast) 1

10 8996-2 15.75$ Clevis Spring Hook (Stainless Steel) 111 8206 16.00$ Clevis Spring (zinc) 212 41041SS 12.50$ 3/8" x 1" Pin, Upper Jaw to Link, short (stainless steel) 113 6912 65.00$ Lower Clevis 7 1/2" (Black Powder Coating) 113 6912Z 65.00$ Lower Clevis 7 1/2" (FDA Powder Coated) 113 6912SS 90.00$ Lower Clevis 7 1/2" (Stainless Steel) 113 6912S 65.00$ Lower Clevis 5 1/2" (Black Powder Coating - Double Mast) 113 6912ZS 65.00$ Lower Clevis 5 1/2" (FDA Powder Coated - Double Mast) 113 6912SS-S 90.00$ Lower Clevis 5 1/2" (Stainless Steel - Double Mast) 114 1206 12.50$ Spring, Jaw to Housing (zinc) 115 10204-1 15.00$ Adjusting Pin (zinc) 116 9016 1.00$ Circle Cotter "Hang 1" Pin Clip (zinc) 117 3006-CP 0.35$ Cotter Pin, 1/8" x 3/4" (zinc) 617 5/32 x 1/2 Roll Pin 0.20$ Stainless Steel 5/32 x 1/2 Roll Pin 2

WLG 7.00$ 12oz White Lithium Grease 1

Assembled Price #1 thru #179004 500.00$ EG1 Single Clamping Mechanism (Black Powder Coating)9004S 500.00$ EG1 Single Clamping Mechanism (Black Powder Coating - Double Mast)9004SRC 650.00$ EG1 Single Clamping Mechanism (Stainless Steel Housing - Non-Sparking)9004SRC-S 650.00$ EG1 Single Clamping Mechanism (Stainless Steel Housing - Non-Sparking - Double Mast)9004SS 725.00$ EG1 Single Clamping Mechanism (Stainless Steel - Non-Sparking)9004SS-S 725.00$ EG1 Single Clamping Mechanism (Stainless Steel - Non-Sparking - Double Mast)

EAGLE-GRIP™ 1 SERIES LIGHT DUTY SINGLE CLAMPING MECHANISMPARTS LIST

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 8/8/2017

19

ITEM PART NO. PRICE EACH DESCRIPTION QTY11 8206 16.00$ Clevis Spring (zinc) 214 1206 12.50$ Spring, Jaw to Housing (zinc) 116 9016 1.00$ Circle Cotter "Hang 1" Pin Clip (zinc) 117 3006-CP 0.35$ Cotter Pin, 1/8" x 3/4" (zinc) 617 5/32 x 1/2 Roll Pin 0.20$ Stainless Steel 5/32 x 1/2 Roll Pin 2

WLG 7.00$ 12oz White Lithium Grease 1

ITEM PART NO. PRICE EACH DESCRIPTION QTY11 8206 16.00$ Clevis Spring (zinc) 213 5516E 40.00$ Optional: Belt Cradle Kit (includes all hardware) 114 1206 12.50$ Spring, Jaw to Housing (zinc) 116 9016 1.00$ Circle Cotter "Hang 1" Pin Clip (zinc) 117 3006-CP 0.35$ Cotter Pin, 1/8" x 3/4" (zinc) 617 5/32 x 1/2 Roll Pin 0.20$ Stainless Steel 5/32 x 1/2 Roll Pin 2

WLG 7.00$ 12oz White Lithium Grease 1ALL ABOVE ITEMS: PART NUMBER EG1BCPMKIT 73.00$

EAGLE-GRIP™ 1 SERIES LIGHT DUTY SINGLE CLAMPING MECHANISMPARTS LIST

EAGLE-GRIP™ 1 SERIES PREVENTATIVE MAINTENANCE KIT

ALL ABOVE ITEMS: PART NUMBER EG1PMKIT 42.00$

EAGLE-GRIP™ 1 SERIES PREVENTATIVE MAINTENANCE WITH BELT CRADLE KIT

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 8/9/2017

20

345

6,12

7

86,13,12

6,12

9

11

10

12

SCALE ERGO EG2DCM CLEVIS SET USES:TOP PIVOT BLOCK WITH STOP BAR3 INCH TOP & BOTTOM CLEVISESNO SPRING HOOK SLIDES MUST BE INSTALLED WITH CLEVIS HOLES FORWARD

REGULAR ERGO EG2DCM CLEVIS SET USES :BOTTOM PIVOT BLOCK WITH STOPS6 INCH TOP CLEVIS5 1/2 INCH BOTTOM CLEVISSPRING HOOKCLEVIS SLIDES MUST BE INSTALLED WITH HOLES TO REAR

1

2

20

21

17,18

15, 16

14

19

22 2328, 29

25

26

33

3132

30

24

27 a

27 b

3034

ERGO EG2LDCM CLAMPING MECHANISM

21

ITEM PART NO. PRICE EACH DESCRIPTION QTY1 7302R 330.00$ Housing, Double Clamping Mechanism (Black Powder Coating) 11 7302RSS 573.00$ Housing, Double Clamping Mechanism (Stainless Steel) 12 10001 13.50$ Bushing, Housing Yolk Trunion (zinc) 13 9107 85.00$ Upper Jaw (Black Powder Coating) 23 9107SRJ 100.00$ Upper Jaw (Spark Resistant) 24 7107 90.00$ Lower Jaw (Black Powder Coating) 24 7107SRJ 100.00$ Lower Jaw (Spark Resistant) 25 4104-1 7.00$ Pin, Upper Jaw to Link, Short (zinc) 26 16104-1SS 13.50$ 3/8" x 1.770" Pin, Upper Jaw Link (stainless steel) 67 1206 12.50$ Spring, Jaw to Housing (zinc) 28 13009-1 13.50$ Link, Jaw to Jaw (zinc) 49 621 25.00$ Fiber Drum Guard (Black Powder Coating) 29 621SS 75.00$ Fiber Drum Guard (Stainless Steel) 2

10 15104-1SS 14.50$ 3/8" x 2.242" Pin, Fibre Guard, Housing to Clevis (stainless steel) 211 7019 1.00$ 3-7/8" Hair Pin Clip (zinc) 212 3006-CP 0.35$ Cotter Pin, 1/8" x 3/4" (zinc) 1613 1470-6 2.00$ Custom Washer EG (zinc) 414 6012R 155.00$ Universal Body (Black Powder Coating) 114 6012RZ 155.00$ Universal Body (FDA Powder Coating) 115 8116 8.00$ 1/2-13 x 1 1/2 Trunion Screw, UNC 116 1/2 LW 0.10$ 1/2 Lock Washer (zinc) 117 1/4-20 x 1 1/4 SHCS 0.40$ 1/4-20 x 1 1/4 Socket Head Cap Screw Alloy Plated 218 1/4 LW 0.85$ 1/4 Lock Washer (zinc) 219 50064 35.00$ Spacer (Black Powder Coating) 119 50064Z 35.00$ Spacer (FDA Powder Coating) 120 64061 23.50$ Universal Pin (zinc) 1

21A 50021R 19.75$ Upper Pivot Block (Black Powder Coating) 121A 50021RZ 19.75$ Upper Pivot Block (FDA Powder Coating) 121B 50021RS 19.75$ Upper Pivot Block (Black Powder Coating - Double Mast) 121B 50021RZS 19.75$ Upper Pivot Block (FDA Powder Coating - Double Mast) 122 4506 1.00$ Roll Pin (zinc) 1

23A 5012R 13.50$ Lower Pivot Block with Oval Stop Bars (Black Powder Coating) 123A 5012RZ 13.50$ Lower Pivot Block with Oval Stop Bars (FDA Powder Coating) 123B 5012RS 13.50$ Lower Pivot Block (Black Powder Coating- Double Mast) 123B 5012RZS 13.50$ Lower Pivot Block (FDA Powder Coating - Double Mast) 124 8002 35.00$ Adjustment Slide (Black Powder Coating) 224 8002Z 35.00$ Adjustment Slide (FDA Powder Coating) 225 8996-2 15.75$ Clevis Spring Hook (Stainless Steel) 126 10204-1 15.00$ Adjusting Pin (zinc) 1

27A 5912R 65.00$ Upper Clevis 6" (Black Powder Coating) 227A 5912RZ 65.00$ Upper Clevis 6" (FDA Powder Coating) 227A 5912RS 65.00$ Upper Clevis 4 7/16" (Black Powder Coating - Double Mast) 227A 5912RZS 65.00$ Upper Clevis 4 7/16" (FDA Powder Coating - Double Mast) 227B 6912R 65.00$ Lower Clevis 5 1/2" (Black Powder Coating) 227B 6912RZ 65.00$ Lower Clevis 5 1/2" (FDA Powder Coating) 227B 6912RS 65.00$ Lower Clevis 4" (Black Powder Coating - Double Mast) 227B 6912RZS 65.00$ Lower Clevis 4" (FDA Powder Coating - Double Mast) 228 16033-1 15.00$ Pin, Clevis (zinc) 229 6006-CP 0.35$ Cotter Pin, 5/32" x 1" (zinc) 430 8206 16.00$ Clevis Spring (zinc) 231 9016 1.00$ Circle Cotter "Hang 1" Pin Clip (zinc) 1

Assembled Price #1 thru #314004R 1,060.00$ EG2L Double Clamping Mechanism (Black Powder Coating)4004RS 1,060.00$ EG2L Double Clamping Mechanism (Black Powder Coating - Double Mast)4004RSRC 1,360.00$ EG2L Double Clamping Mechanism (Stainless Steel Housing - Non-Sparking)4004RSRC-S 1,360.00$ EG2L Double Clamping Mechanism (Stainless Steel Housing - Non-Sparking- Double Mast)

EAGLE-GRIP™ 2 SERIES LIGHT DUTY DOUBLE CLAMPING MECHANISMPARTS LIST

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 8/9/2017

22

PART NO. PRICE EACH DESCRIPTION QTY1206 12.50$ Spring, Jaw to Housing (zinc) 29016 1.00$ Circle Cotter "Hang 1" Pin Clip (zinc) 17019 1.00$ 3-7/8" Hair Pin Clip (zinc) 23006-CP 0.35$ Cotter Pin, 1/8" x 3/4" (zinc) 168206 16.00$ Clevis Spring (zinc) 25516E 40.00$ Optional: Belt Cradle Kit (includes all hardware) 1WLG 7.00$ 12oz White Lithium Grease 1

EAGLE-GRIP™ 2 LIGHT DUTY SERIES PREVENTIVE MAINTENANCE KITPARTS LIST

ALL ABOVE ITEMS: PART NUMBER EG2LPMKIT 90.72$

*Pricing subject to change. www.easylifteqpt.com 800-233-1800 Updated: 8/9/2017

23