class f3p indoor aerobatic power model aircrafts schedule f3p – af-15
TRANSCRIPT
Class F3P Indoor Aerobatic Power Model aIRCRafts
Schedule F3P – AF-15
Security line
Take-off procedure
( not judged, not scored )
F3P-AF-15.01: Knife Edge Golf Ball with 3/4 roll up, half roll integrated, 1/4 roll down
F3P-AF-15.01.01
¾ roll¼ roll
½ roll integrated
F3P-AF-15.01: Knife Edge Golf Ball with 3/4 roll up, half roll integrated, 1/4 roll down
F3P-AF-15.01.01
¾ roll¼ roll
½ roll integrated ½ roll is integrated on
circular flightpath of the ¾ loop.
¾ roll and ¼ roll on middle of the lines.
All radii are equal.
During the knife edge flight the wing must be in the vertical plane.
45°
F3P-AF-15.02: Vertical Eight
F3P-AF-15.02.01
F3P-AF-15.02: Vertical Eight
F3P-AF-15.02.02
All radii are equal.
F3P-AF-15.03: Knife Edge Flight Combination with 1/4 roll, roll, 1/4 roll
F3P-AF-15.03.01
Part rolls must have the same roll rate.
Between rolls and part rolls in opposite direction there must be no line.
F3P-AF-15.04: Figure 6 with stall turn, 1/2 roll down
F3P-AF-15.04.01
Pivot on CG
Stop before pivot
½ roll
F3P-AF-15.04: Figure 6 with stall turn, 1/2 roll down
F3P-AF-15.04.02
Pivot on CG
½ roll
F3P-AF-15.04: Figure 6 with stall turn, 1/2 roll down
F3P-AF-15.04.03
Pivot on CG
½ roll
Two wing spans or more – zero points!
½ roll on middle of the line.
All radii are equal.
F3P-AF-15.05: Cubic Top–Hat with 3/4 roll up, 1/4 roll down, 1/2 roll, 3/4 roll up, 1/4 roll down
F3P-AF-15.05.01
¾ torque roll
¼ roll
½ roll
¾ torque roll¼ roll
F3P-AF-15.05: Cubic Top–Hat with 3/4 roll up, 1/4 roll down, 1/2 roll, 3/4 roll up, 1/4 roll down
F3P-AF-15.05.02
¾ torque roll
¼ roll
½ roll
¾ torque roll¼ roll
All radii are equal.
¾ torque rolls, ¼ rolls and ½ roll on middle of the lines.
F3P-AF-15.06: Half Horizontal Square Circle on Corner with ¼ roll, ½ roll, ½ roll, ¼, roll
F3P-AF-15.06.01
¼ roll
¼ roll
½ roll
½ roll
F3P-AF-15.06: Half Horizontal Square Circle on Corner with ¼ roll, ½ roll, ½ roll, ¼, roll
F3P-AF-15.06.02
¼ roll
¼ roll
½ roll
½ roll
All radii are equal.
½ rolls on middle of the line.
During the knife edge flight the wing must be in the vertical plane.
F3P-AF-15.06: Half Horizontal Square Circle on Corner with ¼ roll, ½ roll, ½ roll, ¼, roll
F3P-AF-15.06.03
¼ roll
¼ roll
½ roll
½ rollOption
¾ rollintegrated
F3P-AF-15.07: Eye-Catcher with two 3/4 rolls integrated in opposite directions
F3P-AF-15.07.01
¾ rollintegrated
¾ rollintegrated
F3P-AF-15.07: Eye-Catcher with two 3/4 rolls integrated in opposite directions
F3P-AF-15.07.02
¾ rollintegrated
Al radii are equal.
Rolls must be in opposite directions.
¾ rolls must be integrated on circular flight path of the ¾ loops.
Roll reversal is immediate.
F3P-AF-15.08.1
F3P-AF-15.08: Half Horizontal Hour Glass with ½ roll down, roll up ½ roll down
½ roll
½ rollroll
F3P-AF-15.08.2
F3P-AF-15.08: Half Horizontal Hour Glass with ½ roll down, roll up ½ roll down
½ roll
½ rollroll
All radii are equal.
45°
½ rolls and roll on middle of the lines.
F3P-AF-15.09.01
F3P-AF-15.09: Horizontal Triangular Circle with 1/4 roll, 1/2 roll integrated, roll, 1/2 roll integrated, roll, 1/2 roll integrated, 1/4 roll
¼ roll
½ roll outside integrated
½ roll outside integrated
roll inside
roll inside
F3P-AF-15.09.02
F3P-AF-15.09: Horizontal Triangular Circle with 1/4 roll, 1/2 roll integrated, roll, 1/2 roll integrated, roll, 1/2 roll integrated, 1/4 roll
¼ roll
½ roll outside integrated
½ roll outside integrated
roll inside
roll inside
F3P-AF-15.09.03
F3P-AF-15.09: Horizontal Triangular Circle with 1/4 roll, 1/2 roll integrated, roll, 1/2 roll integrated, roll, 1/2 roll integrated, 1/4 roll
All ½ rolls are outside and integrated on the flightpath in the corners.
During the knife-edge the wing must be in the vertical plane.
All sides are of equal length, all angles are 60°.
All full rolls are inside and on middle of the lines.
All radii are equal.
F3P-AF-15.10.01
F3P-AF-15.10: Tail Slide with two consecutive 1/8 rolls up
1/8 roll
1/8 roll
F3P-AF-15.10.02
F3P-AF-15.10: Tail Slide with two consecutive 1/8 rolls up
Stick back tail slide.
F3P-AF-15.10.03
F3P-AF-15.10: Tail Slide with two consecutive 1/8 rolls up
1/8 roll 1/8 roll
1/8 rolls centered on middle of the line.
All radii are equal.
Between part rolls in opposite direction there must be no line.
Flipover = 0 points.
F3P-AF-15.11.01
F3P-AF-15.11: Roll Combination with 1 3/4 roll, 1 3/4 roll in opposite direction
Between rolls and in opposite direction there must be no line.
1 ¾ roll
1 ¾ roll
Landing sequence( not judged, not scored )
Peter Uhlig, November 2013
security line