update on tctp heating h. day, b. salvant acknowledgments: l. gentini and the en-mme team
DESCRIPTION
PhD thesis of Hugo Day (2013) Ferrite considered was 8C11 at the timeTRANSCRIPT
![Page 1: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/1.jpg)
Update on TCTP heating
H. Day, B. Salvant
Acknowledgments: L. Gentini and the EN-MME team
![Page 2: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/2.jpg)
Context• Presentation at the collimation working group in March 2012
• Long-standing action for the impedance team, needed to wait for:– the eigenmode solver with dispersive material– Indication that the simulations are relevant (very important for a
complicated geometry such as the TCTP)
![Page 3: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/3.jpg)
PhD thesis of Hugo Day (2013)
Ferrite considered was 8C11 at the time
![Page 4: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/4.jpg)
Simulations of longitudinal impedance• Very heavy simplifications from the initial CATIA file from Luca Gentini• In particular, RF fingers at entry and exit needed to be replaced by a sheet, and
was anyway badly meshed. • Angle of the RF fingers adapted to the jaw position in order to keep contact,
however can be different for the real collimator• 1.7 M mesh cells• All materials perfect conductors, except the ferrite, in order to get rid of the
resistive wall losses from the jaw• Of course, there is uncertainty on
ferrite parameters
Half gap scanned between 1mm and 10 mm
![Page 5: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/5.jpg)
Additional assumptions• Impedance which will heat the ferrite should be broadband• Need to suppress the losses from the resistive wall use
perfect conductor everywhere except for ferrite and assume that superposition is possible.
![Page 6: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/6.jpg)
Simulations of longitudinal impedance
Frequency in GHz
Frequency in GHz
Long
itudi
nal I
mpe
danc
e in
Ohm
Long
itudi
nal I
mpe
danc
e in
Ohm
1 mm
10 mm
Half gap= 1mm
Half gap= 10mm
Opening the gap leads to an increase of the amplitude of broad modes
More heating to ferrrite with gap open Of course, this is not true for resistive wall
heating to the jaws
![Page 7: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/7.jpg)
Superposition of beam spectrum with impedance (50 ns beam)
Pow
er c
ontr
ibuti
on in
WFrequency in Hz
Main contribution from the broad peaks around 500 MHz, peaks beyond 1 GHz only significant for the Gaussian distribution
![Page 8: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/8.jpg)
Superposition of beam spectrum with impedance (25 ns beam)
Pow
er c
ontr
ibuti
on in
W
Frequency in Hz
![Page 9: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/9.jpg)
Power loss (post-LS1, 25 ns, bunch length = 7.5 cm)
50% to 100% of this heat load goes to the two lines of ferrite
![Page 10: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/10.jpg)
Power loss (post-LS1, 25 ns, bunch length = 9 cm)
50% to 100% of this heat load goes to the two lines of ferrite
![Page 11: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/11.jpg)
Power loss vs gap (post-LS1, 50 ns)
50% to 100% of this heat load goes to the two lines of ferrite
![Page 12: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/12.jpg)
Power loss vs gap (HL-LHC, 50 ns)
50% to 100% of this heat load goes to the two lines of ferrite
![Page 13: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/13.jpg)
Power loss vs gap (HL-LHC, 25 ns)
50% to 100% of this heat load goes to the two lines of ferrite
![Page 14: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/14.jpg)
Summary
• Heat load to the ferrite can reach of the order of 5 W per side
• Opening the gap increases the heat load• After LS1, with standard bunch length of 9 cm,
we expect on the order of 1 W in the ferrite per side
![Page 15: Update on TCTP heating H. Day, B. Salvant Acknowledgments: L. Gentini and the EN-MME team](https://reader033.vdocuments.us/reader033/viewer/2022051303/5a4d1b5d7f8b9ab0599abb02/html5/thumbnails/15.jpg)