titan-shredder-ttb353shr-user-manual.pdf

Manufacturer's Warranty

SAFETY AND OPERATING MANUAL

,A, fa

TITAN

Original instructions

RAPID SHREDDER 2500W TTB353SHR

GENERAL SAFETY INSTRUCTIONS WARNING! When using the machine the safety rules must be followed. For your own safety and

bystanders please read these instructions before operating the machine. Do not use the machine without reading the instruction sheet. Please keep the instructions safe for later use. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference. 1. This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

2. Children should be supervised to ensure that they do not play with the appliance.

3. Only use the product in the manner and for the functions described in these instructions.

4. The operator or user is responsible for accide nts or hazards occurring

to other people or their property. 5. Never operate the product when you are tired, ill or under the influence

of alcohol, drugs or medicine. 6. If the supply cord is damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified persons in order to avoid a hazard.

7. It is recommended that appliances should be supplied via a residual current device (RCD) with a tripping current of not more than 30mA.

IMPORTANT: READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE 1. Training

Become familiar with the owner's manual before attempting to operate this equipment.

2. Preparation 1). Do not allow children to operate this equipment or animals. 2). Do not operate this shredder in the vicinity of bystanders.

3). Wear ear protection and safety glasses at all times while operating the machine.

2

A


I.

•.iapeiai inoA oi aa}aa aseaid aaweaen6 sin oi 6uRep.i sauinbua Aue Kid

.Nn agn ui pgen Aluo si aawe.ien6 sigl •sig6u Aaoinieis anoA ioa}}e iou saop aawe.ien6 sigl

spoo6 agi }o asn }o ssoi - saugapin6 s,aa.inioe}nuew nnollo} oi aanned -

a6ewep oRawsop - a6ewep ie}uappoy -

(sauaneq se gons) swell anewnsuoo }o aa ived - aoueua}uiew aui}noa }o loei -

asnge .io asnsiw - .ieal. pue aeann .iied -

:oi. anp pasneo sassoi sapnpxa Alleoi}pads aalueaen6 sigl

•pasegoand senn wail agi aaagnn aauela.i agi pewoo aoueisui is.ii} agi ui Vinous noA 'pouad sigi uigiinn li ne} e sdolanap

ionpo.id inoA }i •sgiuow bZ }o aalue.ien6 e sauaeo ionpo.id •NvLl siyl

3ILN11LI11f!

•amie;aa anoA zoezuoo poiaad siy; uiy;inn zSnel e dolanap }! wogs os 'aa;ueaen6 ipuow-n e taw Sawoo !fool aaMOd •Ndju anoA

'gawp ayp ui uopewao}ui ayp Jo Aue oz aajaa oz peau noA eseo ui loogpuey s!yz uiezaa aseeld •aaeo pue 6unpuey

'Aza}es uo uopewaolui sapnioui loogpuey siy; os 1.i wop aouewao;aad zseq ayz 6ume6 anupuoo oz noA;uenn am •pri (Nfl) slool aannod

uezl1 woa1 lool aannod 711d1u e}o aseyoand anoA uo suopein;ea6uo3

NV 1

disconnect from supply before clearing debris. Keep the power source clear of debris and other accumulations to prevent damage to the power source or possible fire. Remember that operating the starting mechanism on engine powered machines will still cause the cutting means to move.

10). Keep all guards and deflectors in place and in good working condition. 11). Do not tamper with the power source governor settings; the governor

controls the safe maximum operating speed and protects the power source and all moving parts from damage caused by over-speed. Seek authorised service if a problem exists.

12). Do not transport this machine while the power source is running. 13). Shut off the power source and disconnect from supply whenever you

leave the work area. 14). Do not tilt the machine while the power source is running. 15). When feeding material into the product be extremely careful that the

mains cable is not accidently fed into the product. 16). Keep hands and feet away from the cutting means at all times and

especially when switching on the motor. 17). Do not touch the cutting means before the machine is disconnected

from the supply and the cutting means hav e come to a complete stop. 18). Whilst using the product ensure the cable does not become trapped

under the wheels or support feet.

4. Maintenance and storage 1). When the machine is stopped for servicing, inspection, or storage, or

to change an accessory, shut off the power source, disconnect form supply, make sure that all moving parts have come to a complete stop and, where a key is fitted remove the key. Allow the machine to cool before making any inspections, adjustments, etc.

2). When servicing the cutting means be aware that, even though the power source will not start due to the interlock feature of the guard, the cutting means can still be moved by a manual starting mechanism.

3). use only approved replacement parts. 4). Before use the supply and extension cord for signs of damage or

ageing, 5). If the cord becomes damaged during use, disconnect the cord from the

power supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY; 6). Do not use the shredder if the cords are damaged or worn.

5. Additional safety instructions 1). Do not expose to moisture. 2). Use only on AC mains supply voltage shown on the product rating label.

4


~

04.

D

5

!anal aannod punos paawe.ien0

•aoinpe 6u!!o%oaa ao} aaI!elaa ao 4uo4lne !eool inoA w.lnn >Iaayo •1slxa sal1ll!oej a.iaynn aloAoaa aseald ployasnoy

yw■n jo pasodslp aq pinoys slonpoad leou}oala alseM

•1no JO pa6ewep s! algeo sin }! Alalelpaww! su!ew aql 6nld anowa>_l ;AK) HalIMS

aoueuawiew .io 6u!uealo aao}aq su!ew wag. 6nld anowad iAAO HalIMS

6u!uuna si auiyoew all4nn s6u!uado jo lno laal pue spueq daa)l •sapelq 6uRelod laa6uea

•Aenne saapuelsAq deem 'spafqo unnoa yn Aq 1.!g 6ulaq jo aa6uea

uoRoaToad loo} mom

uoRoaload sano16 _mom

uoRoaload aea aeéM uoRoaload aAa aeaM

•spaepuels Alajes luenalaa Ile 01 swaojuop

I1~ lenuew s,aoieaado peed

~

JNINI:I`dM ~

1 Feeding funnel

2 Transportation handle

3 Hopper locking knob

4 Main cable and plug

5 Motor housing

6 Undercarriage

7 Transportation wheels

8 Reset button of overload protector

9 ON/OFF switch

10 Hopper

11 Grass collection bag hook

12 Discharge chutes

13 Ventilation slot

14 Push stick

6


Aal xaH aauuedg

laps gsnd

S3IEIOSS33311 •6uRsodwoo .io}

alsenn uap.ie6 Apoonn pue snoag!} }o 6umno ,io} pau6!sap s! ,iappa.iys slgl 3Sf1 a3aN31NI

•Allaoqo.ne Alddns aannod leool anoA loewoo Aew noA 'uo!}eo!}laelo aanin} aJ!nbai noA }I 'paloadxa Tou am aouegamslp asaql'wg09E£•0 > xewZ s! aouepadw!-suiew agni! 'as!npe am suoseaa leo!ugoai. ao} OS •(spg6!i

6u!ww!p •6•a) wawdlnba aaglo aouan!}u! ueo sm pue an000 Aew sdoap a6e}!on 'dn pe}s uo lonpoad slql }o lndu! aannod aql ol ana iJNINavM

•Aaessaaau GM saanseaw uol;aaload me pue (br)8P98 paaoxa Aew ao;eaado ayl ao; lane! A;lsuaiu! punos ag1

(V)8P 801. !anal aannod punos paalueaenD

(V) 8P E=N '(V) 8P 9.901. lanai aamod punos paanseaW

(V) 8P £=N '(`d) 8PE6 lanai aanssaad punos paansealN

UN 3SION

63I9•6L 11-16laM laN

WE gl6ual aigeo

VXd I lanai uo!}oa}oad aale/N

ww9.17 aalawelp 6uluno •xelN

u!w/ 098Z paads peoi oN

M009Z:(%017)9S 'MOOOZ: LS aannod indu! paleb!

zH09 O`dnOVZ-OEZ a6elion paiebl

L

3d I. 3d I. 3d L

tun Ii13INH331

BEFORE USE INTENDED USE This shredder is designed for cutting of fibrous and woody garden waste for composting. Other uses for the tool will lead to the damage of the tool and a series of dangers to the operator. This tool is intended for DIY home use, or occasional professional use

1. ACCESSORIES Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury

The shredder is supplied with following accessories: ---Main housing ---Support stands (x2) ---Spanner ---Hex key ---Wheels with hub cap (2 sets) ---wheel axle ---Locknut (x2), gasket (x2), screw (M6x5Omm, x2)

2. ASSEMBLY WARNING! Lift your shredder from the carton required two people.

Make sure that you have sufficient space to put the shredder down. Keep your feet apart so that you have a stable position, bend at the knees and keep your back straight. Check all the parts against the components and controls list in the manual. If any parts are missing contact the supplier or service centre.

Your shredder is supplied fully assembled with the exception of the undercarriage assembly. To fit this process as follows: 1). Open the package and remove the machine from package.

8

A


3 •6'd 6

a •6i3

~ •6i3

(3 'a •613) •alxe uo slaagnn aguiasul •a6eia.ieaaapun laagnn alquaassy (~

8 •6'd

y •6ij

(e pue y •613) •icaN xeq wwg pallddns 6ulsn (V) slloq 6uplaolq Z galnn sa6einearapun xl} pue

'a6elaaeaaapun pue 6ulsnog aqn uo saloq u611e '6uisnog aonoua eta sa6euaeaaapun aql 1Jasul •(Z

Fig. H

4). Insert the wheel hub(B) into the wheel and locate into the wheel axle. Gently tap the end of the wheel hub with a hammer until it is almost fully inserted to the wheel axle. (See Fig. F) When disassembling the wheel, step on the undercarriage or wheel with one foot, then pull the other wheel. (See Fig. G)

3. BEFORE USE Always use the correct supply voltage. The power supply voltage must match the information quoted on the tool identification plate. 1). We recommend that you always use the appliance

supplied via a Residual Current Device (RCD) with a tripping current of not more than 30mA.

2). Use only extension cables suitable for outdoor use, preferably with a high visibility cord color. With the following specification:

- For extension cables up to 25 meters, use a wire cross section of 1.5mm2.

- For extension cables over 25 meters and less than 40 meters, use a wire cross section of 2.5mm2.

3). Always completely unwind cable reels.

Fig. F

Fig. G

OPERATION INSTRUCTIONS WARNING! Before using the tool, read the instruction manual carefully.

1. STARTING AND STOPPING. (Fig. H) STARTING. Connect the shredder to a suitable mains supply via an approved extension cable, press the green button "I" to switch the shredder on. The shredder is fitted with a no-volts switch. This prevents the shredder from restarting after a power failure or accidental interruption of the mains supply. In the event of a power failure or accidental interruption of the mains supply the shredder will stop. On reconnection to the mains supply or restoration of the mains power the machine will not restart until the ON/OFF switch is reset. To restart the Shredder simply press the "I" button.

10

A


8

8

8

~

L

jA.infu! sno!aas asnea woo 1! se pueq ano% •au!gaew ag1

ow! je!aa}ew 941 ijnd pue ga}eus sapejg ag1 awilawos'aappaags ag} mu! sagaueag 6u!paa}

pue au!gaew atu 6u!sn uagM iN011fltfa

jaauels!p /gales u! doe)! (sapejg ag1 Aq u! pallnd 6u!aq uagnn Lno gsel moo au!gaew ag~ woa} Lno 6u!puels leualew aa6uol iNOilflva

•uogeJedo 6uianp sanoi6 .ieam pue uoRaalo.id aAa pue aea aeaM sAemI`d iDNINHHVM

•ALdwa s! peed agT ensue '6u!vels aao}a8 iDNINlidM

1tJIEG1tlIN DNIaa3liHS •ti

r •6H •uo!;eaado

aJo;ag Hem paw; senn aaddoy eta ens :310N •uoRe.iado a.io}ag gouN 6upjaoi aaddog

ag1 as!nfojaoja ualg6R sAenniy•una Lou jllM au!gaew ag1 'Ham pan!} Lou .io uado si aaddog ag1 uagM

a~ejd aannoj pue .iaddoy ag; uaann}aq a,insop ag~ uo galIMS rojaaw! go!M pan!} s! .iappa.iys agj

(f '6i3) •,IQOla31NI J1131dVS '£

•6!d

•1-131!nns ddO/NO et-11 uag} pue uounq lasaa ag} 6u!ssa.id Aq 6u!}ae;sa.i

aao}aq alnu!w L Lseal Le }!em aappaags ,inoA ~aa~oad o~ AIleaRewolne su!ew ag1 Lna Ijlnn uoRaalo.id peojaano

ag1'6u!ppaags 6u!.inp pa66op s! au!gaew agl}i •uoi}aa}o.id peojaano e (pm pau6!sap s! au!gaew .ino,k

(I •6id) •NOI133101:Id adO11i3n0 •Z

•uoReaado iewaou ao} papuawwoaa.i ag Lou s! s!u

'aanannoH •qoul 6upiaol aaddog ag} nnaaasun uagan aleaado Lou Ii!nn Lanpoad agl ~N011fl~da •}}o aappaags ag} gal!nns o; „O„ uoung pal ssaad

•DNIddO1S

~

A

A

1). Only insert as much material so as to prevent blockage of the feeding funnel. Chop garden waste that has been stored for some days and is wilted and damp alternately with branches. This prevents the cutting blades from blocking up. Do not fill soft waste such as kitchen rubbish into the shredder. Widely branched material with leaves must be completely chopped before new material is fed. Take care that the chopped material can fall freely from the ejection slot.

2). Keep hold of branches while feeding them into the shredder until they are automatically drawn in.

3). Keep to the working speed of the shredder and do not overload it.

4). To protect the shredder from clogging, shred wilted garden waste that has been left for a few days and shred thin twigs alternately with branches.

5). Before you shred roots, remove any remaining soil and stones from them.

6). Do not shred soft, damp material such as kitchen waste, but take it straight to the compost.

7). Keep a few dry branches for the end, as they will help clean the shredder.

8). Only switch the shredder off when all of the shredding material has passed through the discharge chutes. Otherwise, the discharge chutes may jam the next time you switch the shredder on.

A CAUTION! The ventilation must not be covered

MAINTENANCE AND REPAIR WARNING! Before you replace an accessory settings or perform maintenance work on the device, always be sure that the shredder is switched off and disconnected from power supply !

WARNING ! Always wear glove when cleaning or replacing blade.

12


1 •6id

~ •6id 41.

£L

•s1aed agseld Ao.gsap uea slea!wayo •au!yaew ano% o} a6ewep algeaedaaa! asnea

pinoa asayp. se swanlos JO swa6aaiap asn wu oa •L

•auiyaew uo aamM Aeads JO 19M aanaN •g

••>laonn 6u!ueala ayg 6u!anp saAa anoA laawad o~ sassel6 Alams aeann sAennly •aulyaew anoA ueap

o~ ysnaq l}os e pue yi.op dwep waenn e Aluo asn •g •431.!nns punoae JO aoww ayn. aeau

swan .ye y6noayp. paaawa aney sa!poq u6!aaoi. JO Isnp ou }ey} Alaeln6aa >paya •aaa} pue ueap ida)l sAennle s! 1oo1 agi. jo sels uogel!}uan au 17

•aauewao}aad pue Aaua!a!}}a 6ugsel-6uol u!elgo o} 4eln60a 1! ueap pue au!yaew ano% Io aaea '£

•uosaad pa!}!Ienb AIael!w!s e JO aainaas a!edaa e Aq auop s! l.! ssalun pa6eanoas!p s! sapelq 6u!uadaeys JO >110nn91:1 'sleuo!ssajoad Aq auop ag pinoys apelg wawaaeldaa agi iJNINat/M

•apelg 6umna adAT aayw pelle 1,uop •(£LZ9£ fl>IS) 9>IS/Z0l-031 'ou uogeagguap! e Aq paaeldaa aq lsnw apelg 6ugna ay1 luawaaeldaa

aoj. sued aaeds leu!6!ao asn sAennlb' iJNINatfM •snnaaas nnaaasun Aam xay pa!lddns ay~

asn uayi.'apelg ayl. 6u!aeldaa uaynn 6u!;ewa wanaad o~ nols o}u! aauueds pa!Iddns ayuo pua ayuaasu!

'laoddns apelq ay} pue peog 941 uo sois u6lly •Alddns aannod suiew ayl woa} 6nld ayi laauuoas!p pue j}o yal!nns sAennle 'sapelg uo vonn

6ulueap JO aaueuamew Aue aaolaq 'smalas onn~ y}!nn amid Aaewa paxy. aae apelg alg!saanaa ay1

(1 '6(3) 1N31N33V1d3):1 34v18 JNIllf13 'Z

•au!yaew aleaado aaolaq

qotnl ay} dn ual.y6g pue aaddoy aaeld-au (g

'open aaeds ay} }a6 o} aainaas lea!uyaal. yl!nn laewoa lunlq JO pa6ewep

senn apelq pug noA uaynn 'apelq rayo •(17 'sapelq

ayp. bop Aew slaafgo JO srgs pooM anowaa pue eaae a6aeyas!p pue apelg 6ugna ueao '(£

•aaddoy uado pue as!nnpolague qoul 6uplaol aaddoy nnaaasufl (Z

•Alddns aannod suiew woai. 6nid ay~ laauuoas!p 'llo pauang s! yal!nns ayg aansu3 ( L

(N '6i3) •1i30U31:1HS NV313 '1

8. The tightness of the fastening screws of the undercarriage should be checked from time to time. Periodically check the bolts of the recording equipment on good fit which can be solved over time. Keep all nuts, bolts and screws tight to be sure the appliance is in safe working condition.

9. To protect the shredder from corrosion when storing for a longer period, treat the cutting blade with harmless oil to the environment.

WARNING! The power cord must be replaced only by the manufacturer, from its technical service or by another authorised service center to avoid safety risks.

14


56

•>ln•oo•aaow-apAoaa•nnnnnn }!sin uoqew.io}ui aaylanl aod •aolnpe 6uipAoaa ao} aalielaa JO Auuotuny leoori inoA gum

>loeyo •1.sixa samloe} wow aloAoaa aseald •alsenn ployasno11 ylinn Jo pasodslp aq Tou pinoys slonpoad leouloala alseM

NOLL331O11d MUN3INNO1:1IllN3

leualew pawwef ayo. aeep pue a}nyo a6.ieyosip ayllo weld atu uado 'aaddoy ay} uado pue Aiddns ayu loauuoosia

papolq si aln110 a6,ieyosip au

ui mind lou sl paddoyo aq

ol. lelJalew 941

aaddo11 pue aanoo apelq ay} aoeld-aa 'leualew Noolq

a11l anowaa 'a9noo apelq ayl uado pue'.iaddoy e11i uado pue Aiddns ayl pauuoosia

parolq s! apelg 6umno a111

aaddo11 ay} aoeld-au lalui peal e111 woal leualew

all Ilnd 'aaddoy ay} uado pue Aiddns atu pauuoosia

lalui pea} ayp. u! pawwef si leualew a111

pop Aiddns aannod NI. ra110 amp} aannod

•poiaad uoys e aal}e uo aappaays 9yl uo yo;inns ol

passaad yolinns ddO/NO atu dawl 'uounq lase.] a111 ssead

papuodsaa sag uoi}oaload peolaano a111

uni }ou saop ao;ow ayl

uoipaaaoo lined asneo algissod welgoad

■

JNLLOOHSTI8110H1

16

Green/Yellow ~

i

ll

~ ~.u► ~~e r

BLUE (NEUTRAL) N

OUTER SLEEVE

13AMP FUSE APPROVED TO BS1 362

BROWN (LIVE)

CABLE GRIP

UK PLUG REPLACEMENT The fuse in the main plug of your garden power tool should always be replaced with one of identical rating.Check the voltage given on your garden power tool matches the supply voltage.The garden power tool is supplied with a fitted plug, however if you should need to fit a new plug follows the instruction below.

Important: The wires in the mains lead are coloured in accordance with the following code: Green & yellow - Earth Blue - Neutral Brown - Live.

As the colours of the wires in the mains I ead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green & yellow must be connected to the terminal which is marked with E or ' . The wire which is coloured blue must be connected to the terminal which is marked with N. The wire which is coloured brown, must be connected to the terminal, which is marked with the letter L.Warning: Never connect live or netutral wires to the earth terminal of the plug. Only fit an approved 13 Amp BS1363/A plug and the correct rated fuse.

NOTE: If a moulded plug is fitted and has to be removed take great care in disposing of the plug and severed cable, it must be destroyed to prevent engaging into a socket. If the supply cord is damaged it must be replaced by a service agent or a similarly quàliaed person in order to avoid hazard.


LL 188 ZZ`d8 'anuany pealN 'asnoH apeal •pil(Nfl) slool Jannod uelll

aa6euelN All'eno / sauaeH _lalad :a'l!i / aweN ZLNflf-b/01:1:alep anssl :ainleu6lg

3) L L/L L/90 :area iaploy all; leoluyoal pue Aaoleu6ls pasuoyiny

000Z: L L-E-000 L9N3 600Z:Zd+600Z: L`d+900Z:Z-E-000 L9N3

800Z:Zt1+LOOZ: L`d+L66L:Z-tiL099N3 600Z: L11+900Z: L-bL09SN3

800Z:EEZZ9N3 L LOZ:ZV+600Z: Lt//E89E L N3

0 LO?:ti LV+800Z:E Lt/+900Z:Z Lb'+900Z:Z`d+ti00Z: L LtJ+ti00Z: Lb'+ZOOZ: L-5EE09N3

paaaa;ai suo!leo!3loads leo!uyoal pue spiepuelS

(VIEW 80L Iana3 aannod punoS paa;uerenD — (v)8P 9'90L Ianai aannod punoS pa.inseaw —

(n xauuv / 0 L alnpayos) uollonpoad;o loaluoo leuaalu' ainal luawssasse Al!wio;uoo uasoqo ayi EL alowe / L alnpayos u! pais!' luawdlnba

Jo; anlioaqp ayi ;o III xauuy oi 6u!pa000e senn pannollo; luawssasse Allwio;uoo ayl an!loa.!a sioopinp asn Jo; luawdlnb3 Ag luawuoalnu3

ayl u! uo!ss!w3 as!oN - 33/88/900Z Ag papuawe 33/bL/000Z (333M) luawdlnb3 oluomal3 PUe leoploal3 alSeM - 33/80L/E00Z Pue 33/96/ZOOZ

luawdlnb3 oluoma13 pue leouloa'3 ul saouelsgng snopiezeH ulevaa;o asn ayl;o suolloulsaa - 33/96/ZOOZ

an!loaa!a Aill!q!ledwoa oliau6ewoiloal3 - 33/80L/ti00Z anlloala a6el'on nnol - 33/96/900Z an11.98.11a Aaau!yoeW - 33/Zb/900Z

:sanlioa.ilp 6ulnnollo; ayi yi!M salldwoa

aHSES£811:IapoU11 1i30a3aHS aldtla M009Z :uol;eu6lsaa

ionpoid ayi leyi epaa

11i8 ZZt/8 'anuand peayg 'asnoH apeal Pli bin) slool Jannod Md1I1

aavodwl 'am

A;lwuo;uoa;o uol;eaelaaa

NVL11

8592 l.0 6>i

titan-shredder-ttb353shr-user-manual.pdf

Documents