test for 2g 3g-zhangwenhui

7/29/2019 Test for 2G 3G-Zhangwenhui

1/36

Install TEMS

1.Install

2.Click to install TEMS

3.When finished,copy file in this folderto

NOW, you can open TEMS


2/36

Install MS driver

Open

There is a folder ; inside

MS driverScanner driver

MOS driver


3/36

Quick Guide to the User Interface


4/36

1.Add cellfile


5/36


6/36


7/36

2.Add map


8/36


9/36


10/36


11/36

If we add test route(blue) and city

route, two route not match


12/36

We can change set


13/36

3.Add/Edit Themes


14/36


15/36


16/36

What should we test about 2G?

2G-SSV: we need test 3 items:

DT: Long call; Short call; Ftp download

CQT: Ftp DL; Ftp UL; Call Setup check 2G-Cluster: we need test 6 items:

Long call;Short call;Ftp download;Ftp upload;

Scanner;Mos(need TEMS14 test)


17/36

Attention:2G test

For 2G,youd better use K790i;if you use K800iyou should lock GSM first. Dont use K800i to test2G-FTP_DL and FTP_UL,Because K800i dontsupport EGDE.

If you do CQT(FTP_DL,FTP_UL), W995 is betterqulity for DL/UL speed(first lock GSM).

If device cant connet TEMS,

1.check device driver 2.check data cable and hub

3.check device 4.pull out device and plug in

5.restart TEMS 6.restart computer


18/36

1.2G-SSV

DT:Long call; Short call; Ftp download

Need 3 K790i,1 GPS

CQT:Ftp DL;Ftp UL;Call Setup checkNeed 2 K790i,1 GPS;

Ftp DL and Ftp UL use 1MB file


19/36

Call Setup check:2 MS lock sector1 BCCH,call eachother,the same as sector2 and sector3

Handove check

Inter Sector Handover


20/36

2.2G-POST-BM Long call;Short call;Ftp download;Ftp upload;

Scanner(use TEMS13 test)

Scanner select DCS1800:762-885;E900:1005-

1013

MOS(use TEMS14 test)

About Ftp_UL,youd better use 10MB or 25MB

file to upload, if it upload failed,you should

rename the upload file name.


21/36

Refer to Pre-BM,so you can know where signal

is bad,where has event(like dropped call,handover failure,block call,etc.). When arrivethere,you can stop recording.Pass through

there,start recording. Make sure MS can receive good signal in the

car


22/36

What should we test about 3G?

3G-SSV: we need test 2 items:

DT:Long call; HSDPA

CQT: 384DL;384UL; HSDPA;HSUPA;Call Acessibility Check

3G-Cluster: we need test 12 items:

Long call;Short call;Video long call;Video shortcall;384DL;384UL; HSDPA;HSUPA;CS_IRAT

Test;PS_IRAT_Test; Scanner;Mos(need TEMS14)


23/36


24/36

Attention:3G test

For 3G,you must lock WCDMA first. If you use

W995 to test 3G-384DL and 384UL, you must

select R99.

If you do CQT(384DL,384UL), W995 is better

qulity for DL/UL speed(first lock

WCDMA,select R99).

If device cant connet TEMS,the same as 2G


25/36

1.3G-SSV

DT:Long call; HSDPA

need 1 K800i and 1 data card

CQT: 384DL;384UL; HSDPA;HSUPA;Call Acessibility Check

need 2 W995 or 2 K800i,1 data card


26/36

Call Acessibility Check: 2 MS lock on each

carrier per sector and call each other,the same

as SMS and video call

Handover check

Inter Sector Handover


27/36

2.3G-POST-BM

Long call;Short call;Video long call;Video short

call;384DL;384UL; HSDPA;HSUPA;CS_IRAT

Test;PS_IRAT_Test; Scanner(need TEMS13 test)

Mos(need TEMS14 test)

Scanner select 10787,10812,10837

About 384UL/HSDPA,youd better use 900MB

or 1GB file to upload; if it upload failed,you

should rename the upload file name.


28/36

Refer to Pre-BM,so you can know where signal is

bad,where has event(like dropped call, handover

failure,block call,etc.). When arrive there,you can

stop recording.Pass through there,start recording.

Make sure MS can receive good signal in the car


29/36

MOS TEST

1.ACU(PESQ MOS equipment)


30/36

2.SONY W995


31/36

3. Equipment connect :W995 connect ACU


32/36

4.Audio Cable: black font AUDIO-L connet

port:in/red font connet port:out)


33/36

5.ACU SET :CU_TD1 TEST:


34/36

6.Voice set:In control panel,you can

find voice set


35/36


36/36

7.If PESQ Score have value ,thats ok

test for 2g 3g-zhangwenhui

Documents