tec pos terminal st-7000-c...

Printed in Japan

TEC POS Terminal

ST-7000-C SERIES

Document No. EO10-12027 Original Jun., 2005 (Revised )

Product Description

EO10-12027

TABLE OF CONTENTS

Page 1. OUTLINE OF THE SYSTEM-------------------------------------------------------------------------1- 1 1.1 Features of the POS Terminal --------------------------------------------------------------------------1- 1 1.2 Description of Model Number ---------------------------------------------------------------------------1- 2 1.3 Appearance and Dimensions ---------------------------------------------------------------------------1- 3 1.3.1 Front View/Rear View/Connectors ---------------------------------------------------------------------1- 3

1.4 Basic Specifications ---------------------------------------------------------------------------------------1- 5 1.4.1 Engine Specifications--------------------------------------------------------------------------------------1- 6 1.4.2 Operating Environment ----------------------------------------------------------------------------------1-13 1.4.3 Power Supply Specifications ---------------------------------------------------------------------------1-13 2. DETAILED INFORMATION--------------------------------------------------------------------------2- 1 2.1 Block Diagram ----------------------------------------------------------------------------------------------2- 1 2.2 Block Diagram (PC Board Level)-----------------------------------------------------------------------2- 2 2.3 Detailed Information about PC Standard Functions-----------------------------------------------2- 3 3. DETAILED INFORMATION OF EACH PC BOARD-------------------------------------------3- 1 3.1 CLE266-ENGINE PC Board-----------------------------------------------------------------------------3- 1 3.2 ST7000E RISER PC Board------------------------------------------------------------------------------3- 3 3.3 S.CROSS-IO PC Board ----------------------------------------------------------------------------------3- 6

CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA

TEC. 2. The contents of this manual may be changed without notification. 3. Please refer to your local Authorised Service representative with regard to any queries you

may have in this manual.

Copyright © 2005 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

1. OUTLINE OF THE SYSTEM EO10-12027

1.1 Features of the POS Terminal

1- 1

1. OUTLINE OF THE SYSTEM TEC POS terminal has been developed on the basis of the industry standard PC architecture and with the addition of POS functions, therefore, the POS terminal supports open platform based on the PC architecture. ST-7000-C Series, succeeding the specification of the ST-6500 series and the expandability of the currently released ST-7000 series, adopts a GHz-class CPU (Intel Celeron 1.2 GHz).

1.1 Features of the POS Terminal (1) The Intel Celeron 1.2 GHz CPU is adopted. (It is not possible to upgrade the CPU.) (2) The 128 MB memory (non-ECC type) is installed as standard. Up to 2 GB memory can be installed. (3) Compact design body is adopted in common with the currently released ST-7000 series. (4) The four serial ports (COM1 to COM4), a parallel port, and a USB port are provided as standard. According

to the option I/O board kit, the COM ports and the USB ports are expandable. The option I/O board kit is selectable from the following. • KIT-7000-PUSB-QM (Full I/O (one COM port + three 12V P-USB + one 24V P USB) type)) • KIT-7000-2COM-QM (one COM + one USB type) (5) Windows® XP Professional/Embedded, Windows® 2000, MS-DOS and Linux are supported, however,

neither Windows® 95/98/Me nor Windows® is supported. (6) Same as the ST-7000 series, maintainability has been improved by adopting module design, which allows

easy disassembly without technical tools. (7) A maximum of the two option HDDs and the option CD-R/RD drive can be installed. NOTES: 1. Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation. 2. Intel and Celeron are registered trademarks of Intel Corporation.

1. OUTLINE OF THE SYSTEM EO10-12027 (Revision Date: Sept. 28, 2007)

1.2 Description of Model Number

1- 2

1.2 Description of Model Number ST-7000- T T - T T T T - T QM - T

RoHS Compliance Blank: Non-RoHS compliant model R: RoHS compliant model

Destination, Country/Region Code QM: Standard for Worldwide

Pre-installed OS Blank: None 1: Windows XP Embedded®

Hardware Component

HDD LVDS/DVI Board

Wireless Board

Power Supply Cable RAID Board UPS

00 Not available Not available Not available Not available Not available Not available

01 HDD:30G x 1 LVDS x 2 Not available 3-pin Not available Available

02 HDD:30G x 2 LVDS x 2 Not available 3-pin Available Available

Cabinet Color 00-02: Fair White, 04: Cool Black CPU Type, CPU Clock C: Celeron®1.2GHz E: Celeron®2 GHz F: Pentium®4 2.8GHz

Memory Capacity 1: 128 MB 2: 256 MB 3: 384 MB 4: 512 MB 5: 768 MB

M/S Classification M: Master (for no classification) S: Satellite

Usage M: POS for mass sales shops S: POS for specialty shops F: POS for restaurants W: Common

∗: Japan model NOTE: Some combinations of the above specifications are not released as products.

For details, please contact your nearest authorized TOSHIBA TEC representative.

∗

∗ ∗

∗

∗ ∗ ∗


1.3 Appearance and Dimensions

1- 3

1.3 Appearance and Dimensions 1.3.1 Front View/Rear View/Connectors < Front View > < Rear View > NOTE: Be sure to attach the cable cover for protecting the cables.

Cable Cover

POWER LED

HDD LED

Reset Switch

Volume

Power Switch

USB5 Connector

Cover Catch

CD-RW Drive (Option)

Front Panel Front Panel Lock

Power LED

HDD LED


1.3 Appearance and Dimensions

1- 4

< Connectors >

: Option

*: COM6 is installed on the PCI slot. NOTE: The socket of USB0 to USB3 ports consists of a power supply connector (12V for USB0 to USB2,

and 24V for USB3) and a 5V USB connector. This USB connector can be used in the same way as a general 5V USB connector.

LAN

COM6 (Option)*

Line-out PCI Slot Not Used (Japan model only)

COM5 (Option

COM1

COM3

LPT1

COM2 COM4 VGA DRW1

LVDS (Option)USB4 (Option) 5V USB PS/2 (Keyboard or Mouse)

Not used (Japan model only)

AC Outlet AC Inlet

24V DC Outlet

USB112V-2

USB2 12V-3

USB3 24V

Mic-in

USB0 12V-1

Powered USB x 4

DRW2

5V USB Connector

Power Supply Connector

USB0 USB1 USB2 USB3


1.4 Basic Specifications

1- 5

1.4 Basic Specifications Item Description Remarks

CPU Celeron® 1.2 GHz BIOS ROM Flash ROM 1 MB Chipset VIA: CLE266 + VT8235M

Memory 128 MB (DDR SDRAM) PC2100-compliant, non-ECC type (Up to 2 GB memory is installed.)

HDD Option (Up to two units of the 3.5 inch HDDs can be installed.) Locally purchased

CD-R/RW Option (Only one unit of the CD-R/RW can be installed.)

Locally purchased (KIT-7000-CD-QM is required.)

FDD Option (External USB interface type) Locally purchased RGB (Mini D-sub 15-pin) x 1 Display interface Option LVDS: KIT-7000-DISP3-QM (F.F.U)

Adopts a graphic controller which contains a chipset.

LAN 10/100Base TX (RJ-45 modular connector (with LED)) Supporting Wake-On-LAN function Sound Option KIT-7000-PUSB-QM is required.

PS/2 1 port (MINI-DIN 6-pin) See NOTE below. COM1 Provided D-SUB 9-pin male COM2 Provided D-SUB 9-pin male COM3 Provided D-SUB 9-pin female (with +5V, +12V) COM4 Provided D-SUB 9-pin female (with +5V, +12V)

COM5 Option D-SUB 9-pin female (with +5V, +12V) KIT-7000-PUSB-QM or KIT-7000-2COM-QM is required.

COM6 Option D-SUB 9-pin female (with +5V, +12V) KIT-7000-COM-QM is required. USB0 Option 12V powered USB USB1 Option 12V powered USB USB2 Option 12V powered USB

USB3 Option 24V powered USB

KIT-7000-PUSB-QM or KIT-7000-2COM-QM is required. The Number of additional USB ports differ depending on the option PC board.

USB4 Option 5V USB Option LVDS board is required.

USB5 Provided 5V USB Provided on the front side of the POS terminal.

Drawer 2 ports (Modular type, fitted with the drive circuit) Parallel 1 port (D-SUB 25-pin female) PCI 2 slots (Up to 140 mm size)

Interface

+24VOUT 1 port (DIN 3-pin) DC 24V power supply for the printer UPS battery None None of the UPS battery can be

added. Supported OS Windows® XP Professional/Embedded,

Windows® 2000, MS-DOS and Linux

Power consumption 190 W Dimension 315 mm (W) x 466 mm (D) x 112.5 mm

(including the rubber feet and cable cover)

Weight 9.5 Kg (not including 2 HDDs, CD-RW, PCI, and packing materials)

NOTE: When using the PS/2 keyboard and the PS/2 mouse together, please prepare a store-bought PS/2

splitter which meets the following wiring pattern.

1345

123456 1

345

Keyboard

Mouse

1. OUTLINE OF THE SYSTEM EO10-12027 (Revision Date: Mar. 16, 2007)


1- 6

1.4.1 Engine Specifications 1.4.1.1 PC Functions (1) CPU Intel® Celeron® 1.2 GHz (100 MHz x 12): Socket-370

• Binary interchange with the applications which run on Intel 80x86 family products. • Optimized for 32-bit applications which run on 32-bit OS. • Independently dedicated external system bus and dedicated internal high-speed

cache bus • Embedded with the 16-KB L1 caches for data and for instructions • Integrates an on-die 256-KB L2 cache • Memory address buffer is scalable up to 4-GB memory. • The MMX (Matrix Math eXtensions) technology is adopted. • The 370-pin package type

(2) BIOS-ROM Flash ROM 1 MB • Supports the temperature/voltage monitoring function and the error information log

function • Supports the shadow RAM BIOS function • Programs below are stored in the system BIOS.

- System BIOS program - VGA BIOS program - NETWORK BOOT BIOS program - BIOS DIAG program

(3) Memory (DRAM) 128MB DDR SDRAM (non-ECC type)

Configuration: Two (2) slots are provided for the 2.5 V, 184-pin DIMM connector. The 128-MB memory module is installed into either slot as standard. Memory type: PC2100-compliant, unbuffered, non-ECC type memory module - Supporting a 16 M x 64 bit/32 M x 64 bit/64 M x 64 bit, unbuffered,

non-ECC type DDR-SDRAM module - Supporting CL 2/2.5/3 and 1T per command Capacity: Standard 128 MB/Max. 2 GB Max. 1 GB/slot can be equipped. NOTE: RoHS-compliant memories below are recommended for the ST-7000-WM-

1C00-QM-R

Manufacturer Model Name Memory Type

No. of Pins

Memory Size

CIMA (Nanya） C128M8427D-NAT61AN DDR-DIMM PC2700 184pin 128MB CIMA (Nanya） C256M8427D-NAT1AN DDR-DIMM PC2700 184pin 256MB CIMA (Nanya） C256M8431D-NAT1AN DDR-DIMM PC3200 184pin 256MB CIMA (Nanya） C512M8427D-NAT1N DDR-DIMM PC2700 184pin 512MB CIMA (Nanya） C512M8431D-NATN DDR-DIMM PC3200 184pin 512MB

(4) Chipset VIA Technologies, Inc.: CLE266 (North Bridge) + VT8235M (South Bridge)

Basic Function of CLE266 (North Bridge): • CPU Interface (100/133 MHz FSB controller) • DDR DRAM controller • Internal graphic controller Basic Function of VT8235M (South Bridge): • Low pin count (LPC) interface • 8259-based interrupt controller • I/O APIC • 8254-based timer controller • PCI2.2 bus interface • LAN controller • USB1.1/2.0 host controller • AC’97 interface • SM bus • IDE controller (ATA-33/66/100/133) • Real Time Clock • PS/2 (Keyboard and Mouse) interface • 8237-based DMA controller



1- 7

(5) Super I/O Chip Equipped with SMSC’s LPC47M287 Basic Function: • Controls the COM1, COM2 and LPT1 • FAN control • Voltage monitor (CPU voltage/2.5V/3.3V/5V/12V)

(6) POS Gate Array Equipped with the TEC POS Gate Array EC-B171 (connected to the South Bridge via LPC-ISA Bridge)

Basic Function: • Controls Drawer 1 and Drawer 2 • Controls COM3 to COM6

(7) PS/2 Interface PS/2 (Built in Chipset (South Bridge)) • A MINI-DIN 6-pin connector is provided on the rear side of the POS terminal. • Controls the PS/2 keyboard (PC keyboard or POS keyboard) and the mouse. (When using the PS/2 keyboard and the PS/2 mouse together, please prepare a

store-bought PS/2 splitter.) (8) Serial Interface COM1 and COM2 (Built in super I/O chip)

• PC standard COM1 and COM2 ports • D-SUB 9-pin connector (male) equipped on the POS terminal

Pin Signal I/O 1 DCD (Data Carrier Detect) I 2 RXD (Received Data) I 3 TXD (Send Date) O 4 DTR (Data Terminal Ready) O 5 GND P 6 DSR (Data Set Ready) I 7 RTS (Request To send) O 8 CTS (Clear To Send) I 9 RI (Ring Indicator) I

(9) Parallel Interface LPT1 (Bi-directional) (Built in the super I/O chip)

• PC standard Centronics printer port • Selectable from Output only/Bi-directional/EPP/ECP by the BIOS setting • D-SUB 25-pin connector (female) is equipped on the POS terminal.

PIN Signal I/O PIN Signal I/O 1 /STROBE O 14 /AFD O 2 DATA0 I/O 15 /ERROR I 3 DATA1 I/O 16 /INIT O 4 DATA2 I/O 17 /SLIN O 5 DATA3 I/O 18 GND --- 6 DATA4 I/O 19 GND --- 7 DATA5 I/O 20 GND --- 8 DATA6 I/O 21 GND --- 9 DATA7 I/O 22 GND ---

10 /ACK I 23 GND --- 11 BUSY I 24 GND --- 12 PE I 25 GND --- 13 SLCT I/O

1

6 9

5

1

14

13

25



1- 8

(10) Real Time Clock and Lithium Battery Primary battery • The lithium battery is used for backing up the clock and the setup information. The battery life is five years. • The clock is to be accurate within ± 90 seconds per month.

(11) Speaker Assigned to the I/O interface signal of the RISER PC board.

• A small speaker is built in on the front of the control section (RISER PC board). • Volume can be set with the control on the front side of the POS terminal.

(12) USB Interface, Powered USB Interface Host controller which is contained in VT8235M (South Bridge) • Conforming to the Universal Hub Controller Interface (UHCI) Conforming to the Enhanced Host Controller Interface (EHCI) • The USB host controller controls the six USB2.0/1.1 ports. • The four (4) out of six (6) USB2.0/1.1 ports are connectable via the RISER PC board

with the above USB host controller. • Standard USB: A port is provided on the front side of the POS terminal via the

RISRER PC board. • Four Powered USB ports equipped with 12V/24V power supply can be used. These

ports are provided on the I/O PC board. • Available under Windows®2000 and Windows®XP. • Powered USB should be connected while the system power is on. Available current for USB ports

Voltage Max. Remarks 5V USB A maximum of 0.5 A is available

for one port.

12V USB A maximum of 1.0 A is available for one port. (1.5 A peak/ Less than 2 seconds)

Compliant with Powered USB

24V USB A maximum of 2.0 A is available for one port. (5 A peak/ Less than 2 seconds)

Compliant with Powered USB

NOTE: The socket of USB0 to USB3 ports consists of a power supply connector (12V for USB0 to USB2, and 24V for USB3) and a 5V USB connector. This USB connector can be used in the same way as a general 5V USB connector.

Power Supply Connector

5V USB Connector



1- 9

(13) LAN Interface Conforming to the IEEE802.3 10BASE-T/100BASE-TX Standard • LAN controller: VIA Technologies Inc. VT6105 • Interface: PCI bus master interface • Connector: RJ-45 modular connector (with LED) LED status

Type of LED (Color) LED Status Condition Off A LAN link has not been established. On A LAN link has been established.

LNK/ACT (Green)

Blink Frame being sent/received Off Connected with 10BASE-T SPEED (Yellow) On Connected with 100BASE-TX

(14) HDD Interface IDE interface (Primary/Secondary)

• IDE controller: VT8235 (South Bridge) • Conforming to PIO mode and Ultra ATA/33/66/100/133 • Converts to a 2.54-mm-pitch, 40-pin connector with the RISER PC board. Be sure to prepare an option ATA 80-pin cable for connecting the HDD. • A maximum of two 3.5-inch HDDs (master, slave) can be installed.

NOTE: For details, refer to the HDD specification manual published by HDD manufacturer.

(15) CD-ROM Drive Connected to the secondary side of the IDE interface in use.

When connecting a CD-ROM drive, the SLIM CD interface conversion kit (KIT-7000-CD-QM) is required. The IDE interface can be converted to 50-pin (JAE: KX-50K5D) on the S.CROSS-CD-CONV PC board for allowing the connection of a SLIM-type (using a JAE: KX-50KLDL connector or equivalent) CD-ROM drive, etc. TOSHIBA TEC approved CD-R/RW drive

Model Number Manufacturer Remarks CD-W224E-A93 TEAC Slim type CD-R/RW Drive

LNK/ACT LED

(Green) SPEED LED

(Yellow)

50-p

in C

onne

ctor

S.CROSS-CD-CONV PC Board

40-p

in C

onne

ctor

IDE Cable

CD-ROM Power Cable

KIT-7000-CD-QM

SLIM-type CD-ROM Drive



1-10

(16) Internal graphic interface 1) RGB interface: Analog RGB

• VGA controller: Graphic controller embedded with VIA CLE266 • VIDEO memory: Using system memory (according to the BIOS setting) • VGA BIOS ROM: Stored in system BIOS • Dual display: The internal controller supports the dual display function

between the on-board RGB and the expansion LCD interface (piggyback board) under the OS such as Windows® XP.

Details are depending on the device driver setting. Resolution & Maximum number of colors

OS DOS Windows VIDEO memory 1 MB 8/16/32/64 MB Resolution (Maximum number of colors)

640 x 480 (64K) 800 x 600 (64K) 1,024 x 768 (256)

640 x 480 (16M) 800 x 600 (16M) 1,024 x 768 (16M) 1,152 x 864 (16M) 1,280 x 1,024 (16M)

• Connection with CRT: 15-pin VGA connector (female) PIN Signal I/O PIN Signal I/O 1 RED O 9 NC NC 2 GREEN O 10 GND P 3 BLUE O 11 NC NC 4 NC NC 12 SPD I/O 5 GND P 13 HSYNC O 6 AGND P 14 VSYNC O 7 AGND P 15 SPCLK I/O 8 AGND P

2) Expansion LCD interface: option LVDS board (expandable with the piggyback board) This interface is installed on the ENGINE PC board with the piggyback board, and it

converts the LCD interface signal sent from the ENGINE PC board to the LVDS signal. LVDS interface • VGA controller: Graphic controller embedded with VIA CLE266 • VIDEO memory: Using system memory (according to the BIOS setting) • Resolution: 800 x 600 • Number of colors: Max. 65,536 colors • Connection with engine: Installed on the ENGINE PC board with the piggyback

board (TOSHIBA TEC original board). • Touch panel control: Connected from the LVDS interface to COM4 or COM6

on the ENGINE PC board. • Speaker control: Connected to the internal speaker signal. • Dual display: The internal controller supports the dual display

function between the on-board RGB and the expansion LCD interface (piggyback board) under the OS such as Windows® XP.

Details are depending on the device driver setting.

1 5

11 15



1-11

• Connection with TFT: TOSHIBA TEC original interface 26-pin connector with lock.

Not compatible with the pins of the conventional products.

Signal: LVDS signal (The connector includes the touch panel control RS-232C and speaker control signals.)

PIN Signal I/O PIN Signal I/O 1 +5V --- 14 TXOUT0- O 2 TX0GND --- 15 TXOUT0+ O 3 +5VC --- 16 +12V --- 4 TXOUT1- O 17 TX1GND --- 5 TXOUT1+ O 18 +12V --- 6 SPKR O 19 RXD I 7 TXD O 20 DTR O 8 CTS I 21 RTS O 9 +12V --- 22 TXOUT2- O

10 TX2GND --- 23 TXOUT2+ O 11 BLK O 24 DSR I 12 TXCLK- O 25 TXCGND --- 13 TXCLK+ O 26 GND ---

(17) PCI bus Up to two PCI standard boards can be inserted. • Available board size Lower (Slot0#): Up to 140 mm length x 1 Upper (Slot1#): Up to 140 mm length x 1 • PCI revision Supporting PCI 2.2 • The power is shared by the PCI board, HDDs, USB devices, and other option devices.

(Refer to Section 1.4.3 Power Supply Specifications.) (18) Interface on the I/O PC Board (option)

The option I/O PC board is connected to the RISER PC board. The following I/O ports are expandable depending on the I/O PC board. I/O PC Board 1: (KIT-7000-PUSB-QM: Full I/O type) • Four (4) Powered USB ports (P-USB (12V) x 3, P-USB (24V) x 1) • AC’97 (MIC IN, LINE OUT) • Two serial ports (COM5 and COM6 (Header connector)) • Drawer interface (Japan model only) • Power supply connector for the LIU and printer (Japan model only) I/O PC Board 2: (KIT-7000-2COM-QM: Two COM ports and one 24V P-USB port type) • Two serial ports (COM5 and COM6 (Header connector)) • A Powered USB port (P-USB (24V) x 1)

Expansion I/O Port I/O PC Board 1 KIT-7000-PUSB-QM

I/O PC Board 2 KIT-7000-2COM-QM Remarks

COM5 O O Serial COM6 O O Header connector 12V P-USB (USB0) O X 12V P-USB (USB1) O X 12V P-USB (USB2) O X

USB

24V P-USB (USB3) O O LINE OUT O X AC’97 MIC IN O X Drawer O X PRT PWR O X

Other

LIU PWR O X

Not used for overseas model (Japan model only)

1. OUTLINE OF THE SYSTEM EO10-12027 (revision Date: Mar. 16, 2007)


1-12

(19) Interface on the RISER PC Board The following I/O ports on the RISER PC board are expandable. • POWER LED, HDD LED, POWER SW, RESET SW, BUZZER volume • HDD interface (IDE Interface Primary/Secondary), HDD/CD-ROM power • ATX PS interface • PCI interface • USB interface • 12-24V Step-Up (Boost) DC-DC converter • Printer power connector (24V) • IO board interface • Wake On LAN • PS/2 keyboard (not available) • FAN connector

(20) Watchdog Timer Function

Together with BIOS and OEM drivers, the Watchdog Timer function is activated, which prevents a hang at the time of OS start-up. The Watchdog Timer is a circuit for monitoring the microcomputer’s performance and the system condition and for inquiring the system performance. When detecting some fault condition, an interrupt signal is immediately sent to the CPU and a system restart is performed, resulting in that the system returns from the hung state into normal operation.

1.4.1.2 POS Functions (1) Drawer interface

A maximum of two drawers containing the TOSHIBA TEC standard 24V drive circuit can be connected. • 4-pin modular type x 2 • 4-pin type x 1 (Not used, Japan model only: when the option KIT-7000-PUSB-QM is installed.) Connector specifications

Drawer Connector Type PC Board Remarks

4-pin modular Engine board Drive circuit contained on the drawer side

Drawer 1 4-pin IO board

(Option)

Not used, Japan model only Drive circuit not contained on the drawer side

Drawer 2 4-pin modular Engine board Drive circuit contained on the drawer side

(2) Serial interface

COM1, COM2: 9-pin DSUB (male) as standard COM3, COM4: 9-pin DSUB (female) as standard. +5V and +12V can be supplied. COM5, COM6: 9-pin DSUB (female) (option) +5V and +12V can be supplied. COM5 is provided on the I/O PC board, and COM6 is provided on the I/O PC board or the 10-pin box connector is provided on the RISER PC board. When using COM6, the option KIT-7000-COM-QM is required. COM3 to COM6 do not have the RI and DCD signals.

(3) Powered USB (Installed on the I/O board): option Four Powered USB ports equipped with 12V/24V power supply can be used. These ports are provided on the I/O PC board. • Number of ports supported 12V P-USB x 3, 24V P-USB x 1 (KIT-7000-PUSB-QM) 24V P-USB x 1 (KIT-7000-2COM-QM)

4-pin modular type

4-pin type

COM1 and COM2

COM3 to COM6



1-13

1.4.2 Operating Environment Temperature Operating: 5 °C to 35 °C

Storage: -20 °C to 60 °C Transportation: -20 °C to 60 °C

Relative humidity Operating: 10% to 80%RH No condensation Storage: 10% to 90%RH No condensation Transportation: 10% to 90%RH No condensation

Height above sea level Operating: -60 m to 3,000 m Non-operating: -60 m to 12,000 m

1.4.3 Power Supply Specifications Input voltage/ Consumption current (with outlet)

AC 100V to 240V +10%, -10% 50/60 Hz 4.8A to 2.3A

Output voltage +3.3V ±5%, +5V ±5%, +12V ±5%, -12V ±5%, 5VB ±5% ATX compliance: 20-pin connector, ATX12V, 4-pin connector,

HDD connector 4-pin x 2 Outlet AC 100V to 240V +10%, -10% 50/60 Hz 2.0A to 1.0A

An outlet supplies the power in conjunction with the engine box’s power on/off. Dimension 215 mm (D) x 100 mm (W) x 60 mm (H) Power cord A power cord is not enclosed with the product. Please prepare a power cord locally.

To prevent accidents such as electric shocks and malfunctions, connect the ground to the ground terminal of the outlet. In the United States of America, use the power cord described below: Power cord - UL listed, type SVT, 18/3AWG, rated minimum 125V, 10A Attachment plug - Moulded on type, parallel-blade grounding plug, NEMA5-15P configuration - Moulded on type having standard IEC CE-22 female configuration

Power supply capacity The power is shared by the PCI bus, expandable HDDs, USB devices, and other option devices in the following range: +24V 2A (Peak 10A) +12V 3A (Peak 8.5A) +5V 3.2A (Peak 9A) NOTES: 1. Total consumption current of option devices connected to the POS terminal should

be within rated current of each voltage (+24V, +12V, +5V). If it exceeds the rated current, the POS terminal may malfunction due to shortage of power supply.

2. The system should be constructed so that the total power consumption does not exceed the power supply capacity (133W). As the CPU (Celeron 1.2GHz) consumes a maximum of 36W, the power consumption of the option devices should be within 97W in total.



1-14

Example) The following shows consumption current and power consumption of each voltage when connecting the option devices below to the POS terminal.

• DRWST-51A • PKBST-50 (with PC keyboard) • TRJST-52 • USB FDD (Logitec: LFD-31U4) • TFTST-56T • HDD (Western Digital: WD400BB) • LIUST-51 • CD-R/RW drive (TEAC: CD-W224E) • HS-530

Consumption current: Maximum values are used here. Option device +24V +12V +5V

DRWST-51A 0.2A --- --- TRJST-52 2A --- 0.6A TFTST-56T --- 0.7A --- LIUST-51 --- 0.4A --- HS-530 --- --- 0.2A PKBST-50 (with PC keyboard) --- --- 0.35A USB FDD (Logitec: LFD-31U4) --- --- 0.48A HDD (Western Digital: WD400BB) --- 0.35A 0.63A CD-R/RW Ddive (TEAC: CD-W224E) --- --- 1.6A

Total 2.2A 1.45A 3.86A

Power consumption: 36W + (2.2A x 24V)W + (1.45A x 12V)W + (3.86A x 5V)W = 125.5W CPU +24V Power +12V Power +5V Power

NOTE: The above reference values are obtained on the assumption that all the option devices are performed simultaneously. The consumption current and the power consumption differ depending on operating environment.

Current requirements of the option devices connected to the POS terminal (reference)

Option device +24V (3A) +12V (3A) +5V (5A) DRWST-51A 0.2A --- --- DRWST-56 0.2A --- --- TRJST-52 2A --- --- TRST-56 (external power supply) --- --- --- TFTST-56T --- 0.7A 0.6A LKBST-65 0.8A 0.6A LIUST-51 --- 0.4A --- HS-530 --- --- 0.2A PKBST-50 with PC keyboard --- --- 0.35A PKBST-50 without PC keyboard --- --- 0.04A

--- 0.35A 0.63A --- 0.34A 0.61A --- 0.025A 0.19A

*HDD Read/Write Idle Standby Sleep --- 0.025A 0.08A

--- --- 0.05A

--- --- 1.1A

--- --- 1.0A

--- --- 1.4A

--- --- 1.4A

**CD-R/RW Drive Standby/Sleep Writing at 24x-speed Active At starting At seeking At ejecting --- --- 1.6A USB FDD (Logitec: LFD-31U4) --- --- 0.48A *HDD: Western Digital WD400BB **CD-R/RW Drive: TEAC CD-W224E



1-15

When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your authorized TOSHIBA TEC representative.

(As of September 2004)

Country Agency Certification

mark Country Agency

Certification mark

Country Agency Certification

mark

Australia SAA Germany VDE

Sweden SEMKKO

Austria OVE

Ireland NSAI Switzerland SEV

Belgium CEBEC

Italy IMQ

UK ASTA

Canada CSA

Japan METI

UK BSI

Denmark DEMKO

Netherlands KEMA U.S.A. UL

Finland FEI

Norway NEMKO

Europe HAR

France UTE

Spain AEE

Power Cord Instruction

1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A. 2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V. 3. Please select a power cord with the length of 4.5 m or less.

Country/Region North America Europe United Kingdom Australia

Power Cord Rated (Min.) Type Conductor size (Min.)

125V, 10A SVT No. 3/18AWG

250V H05VV-F 3 x 0.75 mm2

250V H05VV-F 3 x 0.75 mm2

250V AS3191 approved, Light or Ordinary Duty type

3 x 0.75 mm2

Plug Configuration (locally approved type)

Rated (Min.)

125V, 10A

250V, 10A

250V, *1

250V, *1

*1: Minimum 125% of the rated current of the product.

2. DETAILED INFORMATION EO10-12027

2.1 Block Diagram

2- 1

2. DETAILED INFORMATION 2.1 Block Diagram

Celeron 1.2GHz (Socket370)

FLASH-ROM512KB

Basic MemoryMax.1GB

Expanded MemoryMax.1GB

TTL-LVDS Convert

COM4 Header

COM3 Header

USB#4 (5V USB)

LVDS

Touch Panel

VGA

Real Time Clock

PS/2 KeyboardMouse I/F

10/100BASE-/TXDrawer 1

Drawer 2

COM4

COM3

Parallel Port

COM1

COM2

IDE Primary

IDE Secondary

USB#5 (Front)

PS/2 Keyboard I/F

Reset SW

Power SW

PC-BEEP

Power Control

AC-DC Power Supply

ATX

K/B

HDD

HDD

CD-RW

Booster Circuit(12V to 24V)

PCI Slot#1

PCI Slot#2

COM6 Header

24V DC out

Drive Circuit

AC'97Codec

Mic-in

Line-out

24V P-USB#3

12V P-USB#2

12V P-USB#1

12V P-USB#0

COM6

COM5

EC

-B17

1

TTL

DVO

RGB

Speaker I/O PC Board

AC OUTLET

RISER PC Board

AC100/240V

ENGINE PC Board

LCD I/F Board (Piggy)

Drawer(Modular type)

Drawer(Modular type)

ATX

COM5 Header

: Option


2.2 Block Diagram (PC Board Level)

2- 2

2.2 Block Diagram (PC Board Level)

LCD I/F Board (Piggy)

Power Supply

I/O Board

RISER Board

ENGINE BoardIntel Celeron 1.2GHz

SouthBridge

VIAVT8235M

LANController

VIAVT6105

North BridgeVIA CLE266

VGA

COM1

COM2

Parallel

COM3

COM4

DRW1

DRW2

Super I/O

LPC-47M287

Gate Array

EC-B171

BIOS

LPC-ISABridge

EC-B160

DDR DIMM0 (184-pin)

DDR DIMM1 (184-pin)

UDMA66/100

Primary IDE

Secondary IDE

PS/2MOUSE/KB

LAN

Power & Control

ATX

ATX12V AC

PS/2

USB5

RESET

COM6 header

Power Control & DC-DC CNV

Power

Slot#1

Slot#2

VOL

SW

Speaker

AC97

Line-out

Mic-in

COM6 header

P-USB0

P-USB1

P-USB2

P-USB3

DRW1

COM5

DriverCircuit

100-pin

TTLDVORGB

V-Link

DDR266None ECC (up to 2GB)

MOUSE

KB

PCI

ISA

USB0 to 5

LPC

Back light

Back lightCOM4

USB4

COM5 header COM4 header

1st LVDS TTL-LVDS


2.3 Detailed Information about PC Standard Functions

2- 3

2.3 Detailed Information about PC Standard Functions Memory Map

RAM 640KB

VRAM (Graphic mode) 64KB

VRAM (Text mode) 32KB

VGA BIOS 64KB(Shadow RAM)

Data area for USB emulations

UMB 64KB

System ROM BIOS 64KB(Shadow RAM)

RAM2047MB (Max.)

APIC Control Register

System ROM BIOS 1MB

00000h

A0000h

B0000h

C0000h

D0000h

D8000h

E8000h

100000h

80000000h

FEC00000h

FEC00040h

B8000h

FFF00000h

FFFFFFFFh

LAN Boot ROM 64KB(Shadow RAM)



2- 4

I/O Assignment Address (hex) Function PC/POS IC Remarks

0000-001Fh Master DMA Controller PC VT8235 0020-003Fh Master Interrrupt Controller PC VT8235 0040-005Fh Timer/Counter PC VT8235 0060-006Fh Keyboard Controller PC VT8235

0060h KBC DATA PC LPC47M287 0061h Misc Functions & Speaker Control PC VT8235 0064h KBC Control PC LPC47M287

0070-0077h RTC/CMOS/NMI-Disable PC VT8235 0078-007Fh Available for system use PC VT8235

0080h Reserved(Debug port) PC VT8235 0081-008Fh DMA Page Registers PC VT8235 0090-0091h Available for system use PC VT8235

0092h System Control PC VT8235 0093-009Fh Available for system use PC VT8235 00A0-00BFh Slave Interrupt Controller PC VT8235 00C0-00DFh Slave DMA Controller PC VT8235

00E0h System Reserve PC EC-B171 Back Light Control 00F0-00FFh Numeric Data Processor PC VT8235

0100h Multiple Interruption 1 POS EC-B171 Multiple Interruption 1 0110-0117h UPS Control(COM7) POS EC-B171 0118-011Fh System Reserve POS EC-B171 POS-IO#2 0120-0127h System Reserve POS EC-B171 POS-IO#3 0128-012Fh COM5 POS EC-B171 0138-013Fh System Reserve POS EC-B171 POS-IO#1 0140,0144h System Reserve POS EC-B171 RELAY Control

0142h System Reserve POS EC-B171 Multiple Interruption 2 retrigger 0146h Drawer POS EC-B171 014Ah System Reserve POS EC-B171 Multiple Interruption 2 trigger input 014Eh System Reserve POS EC-B171 PFL、M-ON

0152-0158h System Reserve POS EC-B171 OCIA1 0159-015Ch System Reserve POS EC-B171 OCIA2 0170-0177 Secondary IDE PC VT8235 01F0-01F7 Primary IDE PC VT8235 0274-0277h ISA PNP Read Data Port PC VT8235

0279h ISA PNP Read Data Port PC VT8235 02E8-02EFh COM4 POS EC-B171 02F0-02F7h COM6 POS EC-B171 02F8-02FFh COM2 PC LPC47M287

0376 Secondary IDE PC VT8235 0378-037Fh Parallel Port PC LPC47M287 03B0-03BBh VGA Registers PC VT8623 03C0-03DFh VGA Registers PC VT8623 03E8-03EFh COM3 POS EC-B171 03F0-03F5h System Reserve PC LPC47M287 Floppy Controller

03F6 Primary IDE PC VT8235 03F7 System Reserve PC LPC47M287 Floppy Controller

03F8-03FFh COM1 PC LPC47M287 0400-047Fh VT8235 GPIO PC VT8235 0500-050Fh SM Bus PC VT8235 0800-087Fh LPC47M287 GPIO PC LPC47M287

0A79h ISA PNP Read Data Port PC VT8235 CF8-CFBh Configuration Address PC VT8235 CFC-CFFh Configuration Data PC VT8235

0D00-FFFFh PCI Bus PC VT8235 46E8h VGA Registers PC VT8623

D000-D01Fh USB Host Controller PC VT8235 D400-D41Fh USB Host Controller PC VT8235 D800-D81Fh USB Host Controller PC VT8235 DC00-DC0Fh Bus Master IDE Controller PC VT8235 E400-E4FFh VIA VT6105 Rhine III Fast Ethernet Adapter PC VT6105



2- 5

Interruption Assignment

OSInterrupt Level Factor Win2000 WinXP DOS Linux NMI IRQ0 Timer IRQ1 Keyboard IRQ2 8259 (Interrupt Controller) IRQ3 COM2 IRQ4 COM1 IRQ5 COM6/COM7 (UPS) or

PCI/USB

IRQ6 FDD IRQ7 COM5/ (LPT) IRQ8 RTC IRQ9 ACPI or PCI/USB ACPI ACPI PCI/USB ACPI

IRQ10 COM3 IRQ11 COM4 IRQ12 Mouse IRQ13 CoProcessor IRQ14 HDD (Primary) IRQ15 HDD (Secondary) APIC

IRQ16-23 PCI/USB PCI/USB PCI/USB --- PCI/USB

Interrupt switch between COM6 and COM7

Type I/O Address Connection

I/O Connector

COM6 2F0-2F7h 9-pin D-Sub

female

COM7 110-117h UPS Internal wiring

IRQ5

BIOS Setting

3. DETAILED INFORMATION OF EACH PC BOARD EO10-12027

3.1 CLE266-ENGINE PC Board

3- 1

3. DETAILED INFORMATION OF EACH PC BOARD 3.1 CLE266-ENGINE PC Board The CLE266-ENGINE PC board is a heart of the ST-7000 POS terminal. Most of main ICs, such as CPU (Celeron 1.2 GHz), chipset, super I/O IC, gate array IC, are mounted on the PC board. Part of I/O interface, which is controlled by the controller on the PC board, is mounted on the option I/O PC board via the RISER PC board. (1) PCB Layout

Socket370

North Bridge

VIACLE266

South Bridge

VIAVT8235M

VIAVT6105LAN

POSGate ArrayEC-B171

LPC-ISABridgeEC-B160

LPC47M287Super I/O

DDR Memory CN14

DDR Memory CN15

PS/2CN1

Drawer1,2CN2,3

LANCN4

VGA ConnectorCN5 COM4

CN6COM3CN7 COM1, COM2

CN8

LPT Relay CN9

CPU FANCN16

I/O Board Connector (120-pin)

CN10

To RISER PC BoardCN11

To RISER PC BoardCN12


3.1 CLE266-ENGINE PC Board

3- 2

(2) Block Diagram

DC-DC Power Supply

2.5V1.5V

1.25V2.5V

Socket 370

VIAVT8623North Bridge

VIAVT8235MSouth Bridge

V-LINK

LPC I/F

CPU FAN CN16

Clock GeneratorICS9248

Clock BUFFERICS93712

DDR Memory CN14

DDR Memory CN15

COM5,6

K/B

24V12V

5V3.3V5VB

3.3VB

BIOS(8Mbit)

VIAVT6105

LAN

LPC-ISA BridgeEC-B160

POS Gate ARRAYEC-B171

COM5,6

COM4COM3

VGAConnector

CN5

I/O BoardConnector(120-pin)

CN10

COM3,4 (for T.P), COM512V5V3.3V2.5V2.5VB

K/B

USB4

TTLDVO

RGB

IDE

AC'97 I/F

USB I/F (USB0-3,5)

PCI

SMSCLPC47M287

Super I/O

PS/2CN1

COM1CN8

COM2CN8

LPTRelayCN9

COM3CN7

COM4CN6

Drawer1,2

CN2,3

LANCN4

RIS

ER

CN

11,12

CPU Core voltage


3.2 ST7000E RISER PC Board

3- 3

(3) Connector Specifications • DDR-SDRAM (CN14, CN15): 2.5V unbuffered type, 184-pin x 2 • RISER Connector (CN11, CN12): PCI slot x 2

USB x 5 PS/2 keyboard IDE x 2 (Ultra DMA-133/100/66/33) Serial port x 2 (COM5, COM6) Power supply/Power supply control signal Hardware sensor Speaker

• Peripheral I/O Connector: Serial port x 4 (COM1, COM2, COM3, COM4)

Parallel port x 1 (with a relay cable) VGA connector (RGB) x 1 PS/2 keyboard/mouse Connector x 1 (When using the PS/2 keyboard and the PS/2 mouse together, please prepare a store-bought PS/2 splitter) LAN x 1 Drawer (modular type) x 2

• I/O Board Connector (CN10): Display signal (TTL, DVO)

Serial port x 3 (COM3, COM4, COM5) USB x 1 (USB4)

• Other Connector: 3-pin type FAN connector (CN16) from which the FAN rotation speed

read signal is output

3.2 ST7000E RISER PC Board The ST-7000E RISER PC board, equipped with a 24V booster circuit, relays the ENGINE PC board to the I/O PC board. Various connectors such as PCI slots, IDE connectors, power supply connector, and I/O interface connectors required for the front panel are mounted on the PC board. In the 24V booster circuit, 24V is generated with 12V which is input from the ATX power supply. (1) PCB Layout

Power LED (Green)HDD LED (Yellow)Reset Switch

Volume

Power Switch

CN2: USB Connector

CN3: PS/2 Connector(Not installed)

CN102: ATX 12V 4-pin

CN101: ATX 20-pin CN14:Wake on LAN

CN10: HDD PS

CN8: CD R/RW PSCN6: FAN1CN7: FAN2 (Not installed)CN103: UPS I/F

CN9: SpeakerCN11: LED OUT

CN5: Primary IDE

CN15: Secondary IDE

CN19: ENGINE BOARD I/F

CN401:COM6

CN16: PCI Slot #1

CN17: PCI Slot #2

CN18: IO BOARD I/F

CN21: 24V OUT

+5VB



3- 4

(2) Block Diagram

IDE Primary

IDE Secondary

PCI Slot#1

PCI Slot#2

Power Switch

Reset Switch

PS/2 K/B I/F Connector

USB#5 Connector

COM6Connector

IO I/F

Connector

24V Out Connector

HDD Power Connector

CD-R/RW PowerConnector

FAN PowerConnector

12V-24VStep up DC-DC Converter

5VB - 3.3VBRegulator Circuit

3.3VB5VB

12VCPU 24V

USB #5

USB #0,1,2,3

12V5V

3.3V

24V

24V

12V, 5V

12V, 5V

12V

AC97 I/F

COM5,6

DRW1

Speaker

Buzzer

12V CPU12V

5V5VB

3.3V

3.3VB

24V

12V5V

5VB

3.3V-12VP_GOODPSON

12V CPU

UPS I/F

IDE I/F

PCI I/F

EN

GIN

E I/F

Connector

ATX

Connector

ATX

Connector

UP

S

Connector



3- 5

(3) Connector & Switch Specifications • I/O Connector: PCI slot x 2

E-IDE connector x 2 (Ultra DMA-133/100/66/33) PS/2 keyboard connector x 1 USB port x 1 24V OUT connector x 1 (for the RJ printer) UPS interface connector x 1 (Not used) COM6 connector x 1

• Internal interface: ENGINE PC board interface connector x 1

I/O PC board interface connector x 1 Power supply connector: ATX x 2 HDD PS connector x 1 CD-ROM PS connector x 1 Fan connector x 1

• Switch and Volume: Power switch x 1

RESET switch x 1 Buzzer/Speaker volume x 1


3.3 S.CROSS-IO PC Board

3- 6

3.3 S.CROSS-IO PC Board The S.CROSS-IO PC board is an expansion I/O PC board, unique to the ST-7000E series. By the addition of this option PC board, COM5, three 12V P-USBs, 24V P-USB, PRTOUT (24V), LIUOUT (12V), DRW, MIC IN, and LINEOUT are supported as standard. Also, COM6 is supported with the option KIT-7000-COM-QM, which was released for the ST-7000 series. Depending on the required interface, the I/O PC board is selectable either from KIT-7000-PUSB-QM or KIT-7000-2COM-QM. (1) PCB Layout • KIT-7000-PUSB-QM (full I/O type IO PC board)

COM6

FANCN13

CN12

CN1

COM5

12VP-USB1(USB0)

12VP-USB2(USB1)

12VP-USB3(USB2)

24VP-USB1(USB3) 12V24V DRW1

LINEOUT

MICIN

CN10CN9CN6 CN7 CN8

CN2 CN3 CN4 CN5

CN11

RIS

ER

PC

Boa

rd

• KIT-7000-2COM-QM (1 COM + 1 USB type IO PC board)

COM6

FANCN13

CN12

CN1

COM5

12VP-USB1(USB0)

12VP-USB2(USB1)

12VP-USB3(USB2)

24VP-USB1(USB3) 12V24V DRW1

LINEOUT

MICIN

CN10CN9CN6 CN7 CN8

CN2 CN3 CN4 CN5

CN11

RIS

ER

PC

Boa

rd

CN No. CN Name Description KIT-7000

-PUSB-QM KIT-7000

-2COM-QMCN10 MIC IN Used for a microphone Provided Not providedCN9 LINE OUT Used for an external speaker (with built-in amplifier) Provided Not provided

CN8 Drawer Used for a drawer which is not equipped with +24V drive circuit (Not used) Provided Not provided

CN2 12V P-USB (USB0) CN3 12V P-USB (USB1) CN4 12V P-USB (USB2)

Conforming to USB1.1 or USB2.0 (supplying +12V) Provided Not provided

CN5 24V P-USB (USB3) Conforming to USB1.1 or USB2.0 (supplying +24V) Provided Provided CN1 COM5 D-sub 9pin, female (supplying +5V/+12V) Provided Provided

CN12 COM6 (option) Box, 10-pin header (supplying +5V/+12V) Provided Provided CN6 PRTPWR Used for a printer (supplying +5V/+24V) (Not used) Provided Not provided

CN13 FAN Used for an additional FAN (+12V) (Not mounted) Not provided Not providedCN11 CONNECT WITH RISER Used for connecting the RISER PC board (68 pins) Provided Not providedCN7 LIUPWR Used for the LIU (supplying +12V) (Not used) Provided Not provided



3- 7

(2) Block Diagram

AC'97(VT1616)

MIC IN

LINE OUT

Drive Circuit DRW1

12V P-USB1(USB0)

12V P-USB2(USB1)

12V P-USB3(USB2)

24V P-USB1(USB3)

COM5

COM6 (Header)

+12V(LIU PWR)

+24V(PRT PWR)

FAN+12V

+24V

+12V

DRW1

USB0

USB1

USB2

USB3

RIS

ER

PC

BO

AR

D

CN10

CN9

CN8

CN2

CN3

CN4

CN5

CN1

CN12

CN7

CN6

CN13

(3) I/O board specifications • Audio interface:

AC97 interface, which is connected from the ENGINE PC board via the RISER PC board, is converted to AC’97 CODEC (VIA’s VT1616). Input/Output terminal: LINE OUT terminal (stereo mini jack) MIC IN terminal (MONO mini jack)

(4) Drawer interface: (for Japan model only, not used for overseas model) • TOSHIBA TEC standard, 4-pin type connector • A drawer, which is not equipped with 24V drive circuit, is connectable. (5) Powered USB: Host controller contained in VT8235 (South Bridge) • With the above USB host controller, the 4 out of 6 USB1.1/2.0 ports are connectable via the RISER PC

board. • The 4 Powered USB ports with the addition of 12V/24V power supply are available. • Windows® 2000 and Windows® XP are supported. • It is not possible to connect/disconnect the cables to/from the Powered USB while the system is on.



3- 8

(6) Serial interface: COM5, COM6 (10-pin header) • Controller: POS gate array (EC-B171) mounted on the ENGINE PC board Controlled by the ENGINE PC board via the RISER PC board. • Driver/Receiver: Mounted on the ENGINE PC board • Available port: 1 port (COM5: D-SUB 9-pin, female) The option KIT-7000-COM-QM is required for using COM6.

tec pos terminal st-7000-c...

Documents