tec pos terminal st-71 series - toshiba tec...

Printed in Japan

TEC POS Terminal

ST-71 SERIES

Document No. EO10-12028 Original Dec., 2005 (Revised )

Product Description

EO10-12028

TABLE OF CONTENTS

Page 1. OUTLINE OF THE SYSTEM-------------------------------------------------------------------------1- 1 1.1 Features of the POS Terminal --------------------------------------------------------------------------1- 1 1.2 Description of Model Number ---------------------------------------------------------------------------1- 2 1.3 Appearance--------------------------------------------------------------------------------------------------1- 3 1.3.1 Standard Model ---------------------------------------------------------------------------------------------1- 3

1.4 Available Options-------------------------------------------------------------------------------------------1- 4 1.5 Example of POS Terminal with Some Options -----------------------------------------------------1- 4 1.6 Connectors---------------------------------------------------------------------------------------------------1- 5 1.7 Basic Specifications ---------------------------------------------------------------------------------------1- 6 1.7.1 Engine Specifications--------------------------------------------------------------------------------------1- 7 1.7.2 Operating Display Specifications ----------------------------------------------------------------------1-13 1.7.3 Operating Environment ----------------------------------------------------------------------------------1-14 1.7.4 Power Supply Specifications ---------------------------------------------------------------------------1-14 2. DETAILED INFORMATION--------------------------------------------------------------------------2- 1 2.1 Block Diagram ----------------------------------------------------------------------------------------------2- 1 2.2 Block Diagram (PC Board Level)-----------------------------------------------------------------------2- 2 2.3 Block Diagram (Display Section) -----------------------------------------------------------------------2- 3 2.4 Detailed Information about PC Standard Functions-----------------------------------------------2- 4

CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA

TEC. 2. The contents of this manual may be changed without notification. 3. Please refer to your local Authorised Service representative with regard to any queries you

may have in this manual.

Copyright © 2005 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN

1. OUTLINE OF THE SYSTEM EO10-12028

1.1 Features of the POS Terminal

1- 1

1. OUTLINE OF THE SYSTEM ST-71 Series is a high performance POS terminal which has been developed from the Industrial standard PC architecture. This terminal provides all register functions required for a specialty store and enables the user oriented system configuration.

1.1 Features of the POS Terminal (1) The ST-71 Series POS terminal has been designed as a successor of the ST-60 series. Two types of models are prepared according to the front display size, such as 12-inch TFT model and 15-

inch TFT model. (2) The Intel® Celeron® 2.0GHz CPU is adopted. The clock speed is 3 to 3.5 times of tht of the current model such as Celeron 566MHz (ST-60 series) and

ULV Celeron 650 MHz (ST-70 series). (3) The 256 MB memory (non ECC type) is installed as standard. Up to 2 GB memory can be installed. (4) Powered USB is adopted in addition to the USB, PCMCIA, and CF Interface which have been adopted for

the current models. (5) A maximum of the two option HDDs (2.5-inch type) can be installed. (6) Compact design body is adopted in common with the currently released ST-60 series. (7) Windows® XP, Windows® 2000 and Linux are supported, however, neither Windows® 95/98/Me nor

Windows® is supported. NOTES: 1. Windows 2000 and Windows XP are registered trademarks of Microsoft Corporation. 2. Intel and Celeron are registered trademarks of Intel Corporation.

1. OUTLINE OF THE SYSTEM EO10-12028 (Revision Date: Aug. 30, 2007)

1.2 Description of Model Number

1- 2

1.2 Description of Model Number

ST-71- T T - T T T T T - T QM - T RoHS Compliance Blank: Non-RoHS compliant model R: RoHS compliant model

Destination, Country/Region Code QM: Standard for Worldwide

Pre-installed OS Blank: None

Cabinet Color K: Cool Black F: Fair White

Hardware Component Touch Panel HDD PCMCIA/CF

Board LVDS 2ch

Board Memory MSR/I-button Control Board

Additional COM port

00 FCL1 (*1) None Not available Not available 256 MB Not available Not available

01 FCL1 (*1) HDD x1 Available Available 256 MB Available Available

02 FCL1 (*1) None Not available Not available 256 MB Available Not available

*1: 4-wire resistive touch screen

CPU Type, CPU Clock E: Celeron®2 GHz

Memory Capacity 1: 128 MB 2: 256 MB 3: 384 MB 4: 512 MB 5: 768 MB

Screen Size 2A: 12.1-inch TFT 5A: 15-inch TFT

NOTE: Some combinations of the above specifications are not released as products.

For details, please contact your nearest authorized TOSHIBA TEC representative.


1.3 Appearance

1- 3

1.3 Appearance 1.3.1 Standard Model < 12-inch display POS terminal >

< 15-inch display POS terminal >

Brightness Control

Power LED (Green)

HDD LED (Yellow) Speaker

Beep Volume

Reset Switch

Power Switch

Speaker Volume

MIC IN

Brightness Control

Power LED (Green)

HDD LED (Yellow) Speaker

Beep Volume

Reset Switch

Power Switch

Speaker Volume

MIC IN

12” TFT Color Display with Touch Panel

15” TFT Color Display with Touch Panel

2. APPEARANCE EO10-120028

1.4 Available Options

1- 4

1.4 Available Options

12" 2nd Display 15" 2nd Display

LIU Stand

LVDS PC Board

Relay PC Board

iButton Unit MCR COM 5 or 6

Pole Unit

LIU

PCMCIA/CF Board

12" or 15" POS Terminal

1.5 Examples of POS Terminal with Some Options • Example of ST-71 with an optional MCR,

iButton, and 2nd display

• Example of ST-71 with an optional LIU • Example of ST-71 with an optional LIU (Front display: 12/15-inch TFT, Rear display: LIU + LIU stand) (Front display: 12/15-inch TFT, Rear display: LIU + Pole

unit + LIU stand)

2nd Display (Option)

MCR Unit (Option)

iButton (Option)

MCR Unit (Option) (When attached to the left side of the display)

Pole Unit (Option)

LIU (Option)

LIU (Option)

2nd display (Option)

MCR Unit (Option)

• Example of ST-71 with an optional MCRand 2nd display

LIU Stand (Option) LIU Stand (Option)


1.6 Connectors

1- 5

1.6 Connectors

COM5*

COM6* AC Inlet

LVDS1LVDS2*PS/2Mouse

PS/2 Keyboard

USB5

P-USB3

PCMCIA*

CF Card*

Display Power

and Signal

LineOutUSB4LANDRW1 DRW2

LPT

COM4 VGACOM3COM2

COM1

24VDCoutlet

* : Option

Connector Description AC inlet A connector for the AC inlet 24V DC outlet A terminal of a DC 24V line to which the power cable of the Receipt/Journal

printer is connected. PS/2 (Mouse, Keyboard) Mini-DIN 6-pin female type connector

Connector for the PS/2 type mouse, Connector for the PS/2 type keyboard USB3 (USB supplied with power) USB4,5 (General 5V USB)

Connector for the USB (Universal Serial Bus) interface USB V2.0/1.1 and UHCI (conforming to Universal Hub Controller Interface V2.0/1.1)

NOTE: USB functions may not be supported depending on the Operating System.

USB3 is a USB socket supplied with power, which is 1 port of 24V USB. USB4 and USB5 can be used as general 5V USB connectors.

LAN Modular type connector for the 10BASE-T/100BASE-TX LAN interface DRW1, DRW2 A 24V type drawer is connectable. LVDS1, 2 Expandable LCD interface (LVDS2 is a option.) VGA Expandable VGA interface

15-pin VGA female type connector COM1, 2 D-sub 9-pin male type connector (without power)

A slot scanner, modem, serial interface type scale, EFT, etc. are connectable. COM3, 4, 5, 6 D-sub 9-pin female type connector (with +5V, +12V output)

A line display unit or RS-232C type hand scanner is connectable. NOTES: 1. COM4 cannot be used when the touch panel TFT is connected to the POS

terminal. 2. When an optional back indicator unit is installed on the POS terminal, COM3

is not available. 3. COM5 and COM6 are available only when the optional kit is installed.

LPT1 D-sub 25-pin female connector Printer, etc. having a Centronics interface or equivalent are connectable.

Line-out Used for connecting an external speaker via the stereo mini jack terminal CF Card interface slot TYPE II compact flash card conforming to CFA (Compact Flash Association)

standard can be used. PC Card interface slot This complies with PC Card Standard Release 8.0.

32-bit Card Bus card and 16-bit PC card are supported. One slot is provided and accepts up to TYPE II card.


1.7 Basic Specifications

1- 6

1.7 Basic Specifications Description Item

12-inch Display Model 15-inch Display Model Remarks

CPU Celeron® 2 GHz Socket 478 BIOS ROM Flash ROM 1 MB Chipset Intel 82852GME (GMCH) + 82801DB (ICH4)

Memory 256 MB (DDR SDRAM) PC2100/2700 DDR SDRAM with ECC/non ECC type (Up to 2 GB memory is installed.)

HDD Option (Up to two units of the 2.5-inch HDDs can be installed.) Locally purchased

FDD Option (External USB interface type) Locally purchased CF Card Option MIFST-71-2-QM is required PCMCIA Option MIFST-71-2-QM is required

Display interface An RGB port (Mini D-sub 15-pin) and an LVDS port (1st) are provided as standard. LVDS port (2nd): option (NOTE 1)

Adopts a graphic controller which contains a chipset.

LAN 10/100Base TX (RJ-45 modular connector (with LED)) Supporting Wake-On-LAN functionSound AC97 I/F Line Out x1, Mic In x 1

PS/2 2 port (MINI-DIN 6-pin) Keyboard and Mouse COM1 Provided D-SUB 9-pin male COM2 Provided D-SUB 9-pin male COM3 Provided D-SUB 9-pin female (with +5V, +12V) COM4 Provided D-SUB 9-pin female (with +5V, +12V)

COM5 Option D-SUB 9-pin female (with +5V, +12V) KIT-71-COM-QM-R is required COM6 Option D-SUB 9-pin female (with +5V, +12V) KIT-71-COM-QM-R is required

USB1 Provided 5V USB (for connecting the MCR Unit or the iButton Unit)

RISER PC Board

USB3 Provided 24V powered USB RISER PC Board USB4 Provided 5V USB (4-pin connector) ENGINE PC Board USB5 Provided 5V USB (4-pin connector) RISER PC Board Drawer 2 ports (Modular type, fitted with the drive circuit) Parallel 1 port (D-SUB 25-pin female)

Interface

+24VOUT 1 port (DIN 3-pin) DC 24V power supply for the printer

Size 12.1-inch 800 x 600 dots 15.0-inch 1024 x 768 dots FIU

Touch Panel Analog Register Film (1024 x 1024 dots)

Analog Register Film (1024 x 1024 dots)

RIU LCD type Option (12.1-inch or 15 inch) TFTST-71-2A-QM-R (12.1-inch) TFTST-71-5A-QM-R (15-inch)

Fluorescent type

Option (5x7 dot fluorescent display 20 digiys x 2 lines) LIUST-71-BAAK-QM-R is required (NOTE 2)

UPS battery None None of the UPS battery can be added.

Supported OS Windows® XP, Windows® 2000 and Linux Power consumption 250 W Dimension 295.0 mm (W) x 386.8 mm

(D) x 323.5 mm (H) 359.9 mm (W) x 388.1 mm (D) x 371.4 mm (H)

Weight 11.5 Kg 12.5 Kg NOTES: 1. The LVDS (2nd) port is used for connecting a second display which enables the dual display function. For the

dual display function, the option second display (TFTST-71-2A-QM-R orTFTST-71-5A-QM-R) and the KIT-71-DSP1-QM-R are required.

2. For using the fluorescent type of the Remote Display, the LIU Stand (KIT-71-BASE-QM-R) is required.



1- 7

1.7.1 Engine Specifications 1.7.1.1 PC Functions

(1) CPU Intel® Celeron® 2.0 GHz (400 MHz x 5): Socket-478 • Built-in secondary cache memory: Capacity 128KB

(2) BIOS-ROM Flash ROM 1 MB • Supports the shadow RAM BIOS function • Programs below are stored in the system BIOS.

- System BIOS program - VGA BIOS program - NETWORK BOOT BIOS program - BIOS DIAG program

(3) Memory (DRAM) 256MB DDR SDRAM with ECC

Configuration: Two (2) slots are provided for the 2.5 V, 184-pin DIMM connector. The 256-MB memory module is installed into either slot as standard. Memory type: PC2100/2700-compliant, unbuffered, ECC/non ECC type memory

module Capacity: Standard 256 MB/Max. 2 GB Max. 1 GB/slot can be equipped.

(4) Chipset Intel Corporation : 82852GME (North Bridge) + 82801DB (ICH4) (South Bridge) 2 chips Basic Function of 82852GME (North Bridge): • CPU Interface (400/533 MHz FSB controller) • DDR DRAM controller (266/333 MHz DDR SDRAM Controller) • Internal graphic controller Basic Function of VT82801DB (ICH4) (South Bridge): • Low pin count (LPC) interface • 8259-based interrupt controller • I/O APIC • 8254-based timer controller • PCI2.2 bus interface • LAN controller • USB1.1/2.0 host controller • AC’97 interface • SM bus • IDE controller (ATA-33/66/100) • Real Time Clock • BIOS memory control firmware hub (FWH) I/F • 8237-based DMA controller • Power Management function

(5) Super I/O Chip Equipped with SMSC’s LPC47M287 Basic Function: • Controls the Keyboard, Mouse • Controls the COM1, COM2 and LPT1 • FAN control • Voltage monitor (+1.5V/2.5V/5V/12V/Vccp/Vbat/VTR/Vcc)



1- 8

(6) POS Gate Array Equipped with the TEC POS Gate Array EC-B190 (connected to the South Bridge via LPC-ISA Bridge)

Basic Function: • Controls Drawer 1 and Drawer 2 • Controls COM3 to COM6

(7) Keyboard Interface 8042 (Built in super I/O chip) • Controls the PS/2 Keyboard (PC Keyboard or POS Keyboard) and the mouse. • MINI-DIN 6-pin connector equipped on the POS terminal.

(8) Serial Interface COM1 and COM2 (Built in super I/O chip)

• PC standard COM1 and COM2 ports • D-SUB 9-pin connector (male) equipped on the POS terminal

Pin Signal I/O 1 DCD (Data Carrier Detect) I 2 RXD (Received Data) I 3 TXD (Send Date) O 4 DTR (Data Terminal Ready) O 5 GND P 6 DSR (Data Set Ready) I 7 RTS (Request To send) O 8 CTS (Clear To Send) I 9 RI (Ring Indicator) I

(9) Parallel Interface LPT1 (Bi-directional) (Built in the super I/O chip)

• PC standard Centronics printer port • Selectable from Output only/Bi-directional/EPP/ECP by the BIOS setting • D-SUB 25-pin connector (female) is equipped on the POS terminal.

PIN Signal I/O PIN Signal I/O 1 /STROBE O 14 /AFD O 2 DATA0 I/O 15 /ERROR I 3 DATA1 I/O 16 /INIT O 4 DATA2 I/O 17 /SLIN O 5 DATA3 I/O 18 GND --- 6 DATA4 I/O 19 GND --- 7 DATA5 I/O 20 GND --- 8 DATA6 I/O 21 GND --- 9 DATA7 I/O 22 GND ---

10 /ACK I 23 GND --- 11 BUSY I 24 GND --- 12 PE I 25 GND --- 13 SLCT I/O

(10) Real Time Clock and Lithium Battery Primary battery

• RTC compatible with DS1287 and MC 146818A. • The RTC has a battery-backed-up CMOS RAM with 128 bytes x 2 banks. • The lithium battery is used for backing up the clock and the setup information. • The clock is to be accurate within ± 1 minute and 30 seconds per month.

1

6 9

5

1

14

13

25



1- 9

(11) Interface on the RISER board This interface is connected to the RISER board. The following I/Os are expanded

through the interface. • USB x 1, Powered USB x 1 (USB2.0/1.1) • AC’97 • COM5 and COM6 • Primary HDD (12) Interface on the PCMCIA/DF Board This interface is connected to the RISER board. The following I/Os are expanded

through the interface. • PCMCIA • CF (Secondary IDE) (13) USB Interface, Powered USB Interface

Host controller which is contained in 82801DB (ICH4) • Conforming to the Universal Hub Controller Interface (UHCI) Conforming to the Enhanced Host Controller Interface (EHCI) • The one USB host controller controls six USB2.0/1.1 ports. • A USB port is provided on the ENGINE PC Board (USB4) and the RISER PC Board

(USB5) as standard. • A Powered USB port (USB3) which supplies 24V to the RISER PC Board is available. • Available under Windows2000, WindowsXP, and Linux. • Powered USB should be connected while the system power is on. Available current for USB ports

Voltage Max. Remarks 5V USB A maximum of 0.5 A is available

for one port.

24V USB A maximum of 2.0 A is available for one port. (5 A peak/ Less than 2 seconds)

Compliant with Powered USB

NOTE: The socket of USB3 port consists of a power supply connector (24V for USB3) and a 5V USB connector. This USB connector can be used in the same way as a general 5V USB connector.

5V USB Connector Power Supply Connector

(14) Speaker 8 ohrms/0.5W • A small speaker is provided on the Switch PC Board. • The sound volume is adjustable with the speaker volume.

(15) HDD Interface IDE interface (Primary/Secondary) • IDE controller: 82801DB (ICH4) • Conforming to PIO mode , DMA mode, and Ultra ATA/33/66/100 • One channel (Primary) is provided on the RISER PC Board and the other (Secondary)

for the Compact Flash (CF) is provided on the PCMCIA PC Board. • A maximum of two 2.5-inch HDDs (master, slave) can be installed.

NOTE: For details, refer to the HDD specification manual published by HDD manufacturer.

1. OUTLINE OF THE SYSTEM EO10-12028 (Revision Date: Dec. 4, 2006)


1-10

(16) Internal graphic interface 1) RGB interface: Analog RGB

• VGA controller: Graphic controller embedded with Intel 82852GME • VIDEO memory: Using system memory (according to the BIOS setting) • Resolution & Maximum number of colors

OS Linux Windows VIDEO memory 64 MB 64 MB Resolution (Maximum number of colors)

640 x 480 (16M) 800 x 600 (16M) 1,024 x 768 (16M) 1,152 x 864 (16M) 1,280 x 1,024 (16M) 1,600 x 1,200 (16M)

640 x 480 (16M) 800 x 600 (16M) 1,024 x 768 (16M) 1,152 x 864 (16M) 1,280 x 1,024 (16M) 1,600 x 1,200 (16M)

• VGA BIOS ROM: Stored in system BIOS • Dual display: The 852GME internal controller enables dual display

between the on-board RGB and the expandable LCD interface (piggy board) under the OS such as Windows®2000 and XP. Details conform to the device driver settings. However, three screens cannot be displayed at the same time.

• Connection with CRT: 15-pin VGA connector (female)

PIN Signal I/O PIN Signal I/O 1 RED O 9 NC NC 2 GREEN O 10 GND P 3 BLUE O 11 NC NC 4 NC NC 12 SPD I/O 5 GND P 13 HSYNC O 6 AGND P 14 VSYNC O 7 AGND P 15 SPCLK I/O 8 AGND P

2) Expansion LCD interface: expandable with the piggyback board This interface is installed on the ENGINE PC board with the piggyback board, and it

converts the LCD interface signal sent from the ENGINE PC board to the LVDS signal. LVDS interface • VGA controller: Graphic controller embedded with Intel 82852GME • VIDEO memory: Using system memory (according to the BIOS setting) • Resolution: 12-inch display: SVGA (800 x 600 dots) fixed 15-inch display: XGA (1024 x 768 dots) fixed • Connection with ENGINE: Installed on the ENGINE PC board with the piggyback

board (TOSHIBA TEC original board). • Touch panel control: Connected from the LVDS interface to COM3 or COM4

on the ENGINE PC board. • Speaker control: Connected to the internal speaker signal. • Connection with TFT: TOSHIBA TEC original interface 26-pin connector with

lock. Not compatible with the pins of the conventional

products.

1 5

11 15



1-11

• Signal: LVDS signal (The connector includes the touch panel control RS-232C and speaker control signals.)

PIN Signal I/O PIN Signal I/O 1 +5V --- 14 TXOUT0- O 2 TX0GND --- 15 TXOUT0+ O 3 +5VC --- 16 +12V --- 4 TXOUT1- O 17 TX1GND --- 5 TXOUT1+ O 18 +12V --- 6 SPKR O 19 RXD I 7 TXD O 20 DTR O 8 CTS I 21 RTS O 9 +12V --- 22 TXOUT2- O

10 TX2GND --- 23 TXOUT2+ O 11 BLK O 24 DSR I 12 TXCLK- O 25 TXCGND --- 13 TXCLK+ O 26 GND ---

(17) LAN Interface Conforming to the IEEE802.3 10BASE-T/100BASE-TX Standard

• LAN controller: VIA Technologies Inc. VT6105 • Interface: PCI bus master interface • Connector: RJ-45 modular connector (with LED) LED status

Type of LED (Color) LED Status Condition Off A LAN link has not been established. On A LAN link has been established.

LNK/ACT (Green)

Blink Frame being sent/received Off Connected with 10BASE-T SPEED (Yellow) On Connected with 100BASE-TX

LNK/ACT LED

(Green) SPEED LED

(Yellow)



1-12

1.7.1.2 POS Functions (1) Drawer interface

A maximum of two drawers containing the TOSHIBA TEC standard 24V drive circuit can be connected. • 4-pin modular type x 2 • 4-pin type x 1 (Not used, Japan model only: when the option KIT-7000-PUSB-QM is installed.) Connector specifications

Drawer Connector Type PC Board Remarks

Drawer 1 4-pin modular Engine board Drive circuit contained on the drawer side

Drawer 2 4-pin modular Engine board Drive circuit contained on the drawer side

(2) Serial interface

COM1, COM2: 9-pin DSUB (male) as standard COM3, COM4: 9-pin DSUB (female) as standard. +5V and +12V can be supplied. COM5, COM6: 9-pin DSUB (female) (option) +5V and +12V can be supplied. COM5 and COM6 are provided on the RISER PC board. When using COM5 or/and COM6, the option KIT-71-COM-QM-R is required. COM3 to COM6 do not have the RI and DCD signals. Power supply from the Serial Interface

Voltage Current 5V 1A/port

12V 750mA/port

(3) Powered USB (Installed on the RISER board): A Powered USB port which supplies 24V to the RISER PC Board is available.

4-pin modular type

COM1 and COM2

COM3 to COM6

1. OUTLINE OF THE SYSTEM EO10-12028 (Revision Date: Dec. 4, 2006)


1-13

1.7.2 Operating Display Specifications 1.7.2.1 12-inch model

12.1-inch color TFT Display Size 12.1-inch Resolution SVGA (800 x 600 dots) fixed Max. number of colors 262K (262,144 colors)

Brightness Control Adjustment Mechanism Tilt Angle: 0° to 90°

Power LED (Green) Lights at the power on time LED HDD LED (Yellow) Lights on having an access to the HDD or CF. Method Analog Register Film Resolution 1024 x 1024 dots Input method Pushed by fingers

Touch Panel

Baud Rate 9600 bps fixed 1.7.2.2 15-inch model

15-inch color TFT Display Size 15-inch Resolution XGA (1024 x 768 dots) fixed Max. number of colors 262K (262,144 colors)

Brightness Control Adjustment Mechanism Tilt Angle: 0° to 90°

Power LED (Green) Lights at the power on time LED HDD LED (Yellow) Lights on having an access to the HDD or CF. Method Analog Register Film Resolution 1024 x 1024 dots Input method Pushed by fingers

Touch Panel

Baud Rate 9600 bps fixed



1-14

1.7.3 Operating Environment Temperature Operating: 5 °C to 35 °C

Storage: -20 °C to 60 °C Transportation: -20 °C to 60 °C

Relative humidity Operating: 10% to 80%RH No condensation Storage: 10% to 90%RH No condensation Transportation: 10% to 90%RH No condensation

Height above sea level Operating: -60 m to 3,000 m Non-operating: -60 m to 12,000 m

1.7.4 Power Supply Specifications Input voltage/ Consumption current (with outlet)

AC 90V to 264V 50/60 Hz 5.0A (115V) to 2.5A (230V)

Output voltage/ current Voltage Minimum current value (A) Maximum current value (A)

+3.3V ±5% 0.3 16.0 +5V ±5% 2.0 25.0

+12V ±5% 0.2 15.0 -5V ±5% 0.0 0.3

-12V ±5% 0.0 0.8 +5VSB ±5% 0.0 2.0

ATX compliance: 20-pin connector, ATX12V, 4-pin connector,

Power cord A power cord is not enclosed with the product. Please prepare a power cord locally. To prevent accidents such as electric shocks and malfunctions, connect the ground to the ground terminal of the outlet. In the United States of America, use the power cord described below: Power cord - UL listed, type SVT, 18/3AWG, rated minimum 125V, 10A Attachment plug - Moulded on type, parallel-blade grounding plug, NEMA5-15P configuration - Moulded on type having standard IEC CE-22 female configuration

Power supply capacity The power is shared by the PCI bus, expandable HDDs, USB devices, and other option devices in the following range: +24V 3A (Peak 10A) +12V 2A +5V 2A NOTES: 1. Total consumption current of option devices connected to the POS terminal should

be within rated current of each voltage (+24V, +12V, +5V). If it exceeds the rated current, the POS terminal may malfunction due to shortage of power supply.

2. The system should be constructed so that the total power consumption does not exceed the power supply capacity (250W). As the CPU (Celeron 2.0GHz) consumes a maximum of 72W, the power consumption of the option devices should be within 178W in total.



1-15

When purchasing the power cord Since the power cord set is not enclosed in this unit, please purchase an approved one that meets the following standard from your authorized TOSHIBA TEC representative.

(As of September 2004)

Country Agency Certification

mark Country Agency

Certification mark

Country Agency Certification

mark

Australia SAA Germany VDE

Sweden SEMKKO

Austria OVE

Ireland NSAI Switzerland SEV

Belgium CEBEC

Italy IMQ

UK ASTA

Canada CSA

Japan METI

UK BSI

Denmark DEMKO

Netherlands KEMA U.S.A. UL

Finland FEI

Norway NEMKO

Europe HAR

France UTE

Spain AEE

Power Cord Instruction

1. For use with 100 – 125 Vac mains power supply, please select a power cord rated Min. 125V, 10A. 2. For use with 200 – 240 Vac mains power supply, please select a power cord rated Min. 250V. 3. Please select a power cord with the length of 4.5 m or less.

Country/Region North America Europe United Kingdom Australia

Power Cord Rated (Min.) Type Conductor size (Min.)

125V, 10A SVT No. 3/18AWG

250V H05VV-F 3 x 0.75 mm2

250V H05VV-F 3 x 0.75 mm2

250V AS3191 approved, Light or Ordinary Duty type

3 x 0.75 mm2

Plug Configuration (locally approved type)

Rated (Min.)

125V, 10A

250V, 10A

250V, *1

250V, *1

*1: Minimum 125% of the rated current of the product.

2. DETAILED INFORMATION EO10-12028

2.1 Block Diagram

2- 1

2. DETAILED INFORMATION 2.1 Block Diagram

Celeron 2.0GHz (mPGA478)

FLASH-ROM8 Mbit

Basic MemoryMax. 1GB

Expanded MemoryMax. 1GB

Real Time Clock(RTC)

Parallel Port 1

10/100BASE-/TX

EC

-B19

0

232C COM3

232C COM4

Drawer 1

Drawer 2

PS/2 Keyboard I/F

PS/2 Mouse I/F

232C COM1

232C COM2

USB#4

DVO - LVDS Convert

COM3 Header

COM4 Header

VGA

FIU TFT

FIU Touch Panel

BIU TFT

BIU Touch Panel

232C COM5

232C COM6

USB#5

24V P-USB#3

Line OUTAv97Codec

Mic IN

SPK VOL Control

BEEP VOL Control

PC cardI/F

USB #1

P-SW

Reset SW

MCR/i-Button

Speaker

PiezoelectricBuzzer

PC Card

CF Card

IDE Secondary

IDE PrimaryHDD

HDD

DVO

LVDS

ENGINE PC Board

RISER PC Board

SW PC Board

PCMCIA PC Board

LCD I/F Board (Piggy)

: Option


2.2 Block Diagram (PC Board Level)

2- 2

2.2 Block Diagram (PC Board Level)

DDR DIMM0 (184-pin)

DDR DIMM1 (184-pin)

SW

RESET

Mic IN

SPK

Speaker VOL

BEEP VOL

PCMCIAControllerPC Card

CF PowerSupply

USB#1

USB#5

P-USB#3

COM5

COM6

24V OUT

Power

Power&

Control

Primary IDE

LineOUT

Buzzer

AC97

1st LVDS

2 nd LVDS LVDS DVO

VGA

COM1

COM2

Parallel

PS/2 K/B

PS/2 Mouse

COM3

LPC47M287LPC

Super I/O

COM4

DRW1

DRW2

USB#4

GateArray

EC-B190 BIOS

SouthBridge

Intel82801DB

ICH4

Secondary IDE

LANCNT LAN

North BridgeIntel 853GME

Intel Celeron 2.0GHz

LVDS

DVO

RGB

FSB400/533

DDR266/333with ECC (up to 2GB)

LPC

COM3 (Second LVDS Display)

COM4 (First LVDS Display)

Back Light

Back Light

USB0 to 5

80-pin

DC12/5/3.3V, 5VB

PF

ON CTRL

AC90 to 240V

ENGINE PC Board

RISER PC Board

SW PC Board

PCMCIA PC Board


2.3 Block Diagram (Display Section)

2- 3

2.3 Block Diagram (Display Section)

Back Light Inverter

LEDinput

LVDSinput

LVDSDecoder

LCD of LVDS LCD of TTL input

Touch Panel

Brightness ControlHDD LED (Yellow)

Power LED (Green)

from LVDS

from RISER PC Board

FPCNT PC Board

VOL PC Board


2.4 Detailed Information about PC Standard Functions

2- 4

2.4 Detailed Information about PC Standard Functions Memory Map

RAM 640KB

VRAM (Graphic mode) 64KB

VRAM (Text mode) 32KB

VGA BIOS 64KB(Shadow RAM)

Data area for USB emulations

UMB 64KB

System ROM BIOS 64KB(Shadow RAM)

Expanded Memory2047MB (Max.)

System ROM BIOS 1MB

00000h

A0000h

B0000h

C0000h

D4000h

D8000h

E8000h

100000h

80000000h

B8000h

FFF00000h

FFFFFFFFh

LAN Boot ROM (PXE)

D0000h

SRAM

Expansion for a1024 x 768 dot-or-more

Graphic mode



2- 5

I/O Assignment ADDRESS (hex) Characterization PC/POS IC Remarks

0000-001F DMA Controller PC ICH4 0020-0021 Interrupt Controller PC ICH4 0024-0025 Interrupt Controller PC ICH4 0028-0029 Interrupt Controller PC ICH4 002C-002D Interrupt Controller PC ICH4 002E-002F LPC SIO PC LPC47M287 0030-0031 Interrupt Controller PC ICH4 0034-0035 Interrupt Controller PC ICH4 0038-0039 Interrupt Controller PC ICH4 003C-003D Interrupt Controller PC ICH4 0040-0043 Timer/Counter PC ICH4 004E-004F LPC SIO PC LPC47M287 0050-0053 Timer/Counter PC ICH4

0060 Keyboard Controller PC LPC47M287 0061 NMI Controller PC ICH4 0062 Microcontroller (LPC) PC LPC47M287 0063 NMI Controller PC ICH4 0064 Keyboard Controller PC LPC47M287 0065 NMI Controller PC ICH4 0066 Microcontroller (LPC) PC LPC47M287 0067 NMI Controller PC ICH4

0070-0077 System CMOS/RTC PC ICH4

0080-0091 DMA Controller PC ICH4 0092 Reset Generator PC ICH4

0093-009F DMA Controller PC ICH4 00A0-00A1 Interrupt Controller PC ICH4 00A4-00A5 Interrupt Controller PC ICH4 00A8-00A9 Interrupt Controller PC ICH4 00AC-00AD Interrupt Controller PC ICH4 00B0-00B1 Interrupt Controller PC ICH4 00B2-00B3 APM PC ICH4 00B4-00B5 Interrupt Controller PC ICH4 00B8-00B9 Interrupt Controller PC ICH4 00BC-00BD Interrupt Controller PC ICH4 00C0-00DF DMA Controller PC ICH4 00F0-00FF Numeric Data Processor PC ICH4 0170-0177 Secondary IDE PC ICH4 01F0-01F7 Primary IDE PC ICH4

0CF9 Reset Control PC ICH4 03F8-03FF COM1 (male) PC LPC47M287) 02F8-02FF COM2 (male) PC LPC47M287) 03E8-03EF COM3 (female) POS EC-B190

0376 Secondary IDE PC ICH4 0378-037F Parallel Port PC LPC47M287 03B0-03BB 82852GME Graphics Controller PC 852GME 03C0-03DF 82852GME Graphics Controller PC 852GME (03F0-03F5) FDC PC LPC47M287 Not used

03F6 Primary IDE PC ICH4 (03F7) FDC PC LPC47M287 Not used

04D0-04D1 Interrupt Controller PC ICH4 0110-0117 Switch status (COM7 bit0) POS EC-B190 0CF8-0CFB PCI Configuration address register PC ICH4 0CFC-0CFF PCI Configuration data register PC ICH4 02E8-02EF COM4 (female) POS EC-B190 0128-012F COM5 (female) POS EC-B190 (Optional) 02F0-02F7 COM6 (female) POS EC-B190 (Optional)

0146 Drawer POS EC-B190

- - -

0110-0117 UPS (COM7) POS EC-B190 Not used

0274-0277 ISA PNP Read Data Port PC ICH4 0279 ISA PNP Read Data Port PC ICH4

0E0,0100 System Reserve POS EC-B190 0118-011F System Reserve POS EC-B190 0120-0127 System Reserve POS EC-B190 0138-013F System Reserve POS EC-B190

0140,0142,0144 System Reserve POS EC-B190 014A,014E System Reserve POS EC-B190 0152-015C System Reserve POS EC-B190 03F0-03F5 System Reserve POS EC-B190 0400-047F Power Management PC ICH4 0480-04BB ICH4 GPIO PC ICH4 0500-0517 SMBus PC ICH4



2- 6

Interruption Assignment

OSInterrupt Level Factor Win2000 WinXP Linux NMI IRQ0 Timer

IRQ1 Keyboard

IRQ2 8259 (Interrupt Controller)

IRQ3 COM2

IRQ4 COM1

IRQ5 COM6/COM7 (UPS) or PCI/USB

IRQ6 FDD

IRQ7 COM5/ (LPT)

IRQ8 RTC

IRQ9 ACPI or PCI/USB ACPI ACPI ACPI IRQ10 COM3

IRQ11 COM4

IRQ12 Mouse

IRQ13 CoProcessor

IRQ14 HDD (Primary)

IRQ15 HDD (Secondary)

APIC IRQ16-23

PCI/USB PCI/USB PCI/USB PCI/USB

Interrupt switch between COM6 and COM7

Type I/O Address Connection

I/O Connector

COM6 2F0-2F7h 9-pin D-Sub

female

COM7 110-117h UPS Internal wiring

IRQ5

BIOS Setting

tec pos terminal st-71 series - toshiba tec...

Documents