solid cylinder cut at an angle drawing abilities teacher © j lewis 2004
TRANSCRIPT
![Page 1: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/1.jpg)
Solid Cylinder cut at an angle
Drawing Abilities Teacher
© J Lewis 2004
![Page 2: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/2.jpg)
Orthographic projection
Plan
Elevation
Draw the Plan and Elevation of the cylinder, which is cut at an angle of 30 °
© J Lewis 2004
![Page 3: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/3.jpg)
Drawing generators
Divide the plan into 12 equal generators at 30 °, number these as shown
© J Lewis 2004
Plan
Elevation
![Page 4: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/4.jpg)
Inserting reference points
Project the vertical generators down to the Elevation and number as shown
© J Lewis 2004
Elevation
![Page 5: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/5.jpg)
Starting the End Elevation
Construct the outline of the End Elevation, point 3 at the front and the generators shown
© J Lewis 2004
Elevation End Elevation
![Page 6: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/6.jpg)
Drawing horizontal generators
Construct horizontals where the vertical generators cross the sloping top of the Elevation
© J Lewis 2004
Elevation End Elevation
![Page 7: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/7.jpg)
Marking out the shapeNow mark the End Elevation. Points are found where horizontal lines cross similar marked generators.
© J Lewis 2004
Elevation End Elevation
![Page 8: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/8.jpg)
Drawing the ellipse
Draw an ellipse passing through the marked points
36
(12)(10)(11)789 6
(2)(1)45 3
(11)12
(8)4
(7)6 5
(9)(10)3 2 1
© J Lewis 2004
Elevation End Elevation
![Page 9: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/9.jpg)
Finished End Elevation
© J Lewis 2004
![Page 10: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/10.jpg)
Surface Development
Project horizontals from the Elevation and step off to circumference length in 12 steps
© J Lewis 2004Elevation
![Page 11: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/11.jpg)
Marking points
Mark the reference points carefully as shown below
© J Lewis 2004
Elevation
![Page 12: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/12.jpg)
Joining the points
Join the points with a smooth curve
© J Lewis 2004
Elevation
![Page 13: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/13.jpg)
Finished Surface Development
© J Lewis 2004
Plan
Elevation Surface Development
![Page 14: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/14.jpg)
Dealing with ConesCones are dealt with in a similar way to cylinders
The Plan and Elevation of the cone, which is cut at an angle of 30 ° by the plane A – A are shown below
© J Lewis 2004
![Page 15: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/15.jpg)
Drawing generators
Divide the Plan into 12 equal generators at 30 °, number these as shown
© J Lewis 2004
![Page 16: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/16.jpg)
Inserting reference pointsProject the vertical generators down to the Elevation and number as shown
© J Lewis 2004
![Page 17: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/17.jpg)
Drawing Surface GeneratorsDraw surface generators as shown
© J Lewis 2004
![Page 18: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/18.jpg)
Starting the End ElevationConstruct the outline of the End Elevation, point 3 at the front and the generators shown
© J Lewis 2004
Elevation End Elevation
![Page 19: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/19.jpg)
Starting the End ElevationConstruct surface generators on the End Elevation as shown
© J Lewis 2004
Elevation End Elevation
![Page 20: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/20.jpg)
Drawing the End ElevationConstruct horizontals as shown
© J Lewis 2004
Elevation End Elevation
![Page 21: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/21.jpg)
Drawing the End ElevationDraw a smooth curve as shown on the End Elevation
© J Lewis 2004
End Elevation
![Page 22: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/22.jpg)
Starting the PlanConstruct the lines shown from the Elevation up to the Plan
© J Lewis 2004
Elevation
Plan
![Page 23: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/23.jpg)
Completing the PlanTransfer the measurement on 6 – 12 on the End Elevation to the same generator on the Plan and draw a smooth curve as shown.
© J Lewis 2004
Elevation
Plan
End Elevation
![Page 24: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/24.jpg)
Finished Orthographic Projection
© J Lewis 2004
![Page 25: Solid Cylinder cut at an angle Drawing Abilities Teacher © J Lewis 2004](https://reader034.vdocuments.us/reader034/viewer/2022051517/56649c915503460f9494c4be/html5/thumbnails/25.jpg)
Surface DevelopmentStep off to circumference length in 12 steps along an arc with the same radius as generator 3 as shown – this is a true length of side
Mark off the true lengths of each of the generators as shown and draw the surface development
© J Lewis 2004
Elevation