Exposure to ultraviolet (UV) radiation from the sun is the major cause of skin cancer. In some countries the UV radiation

is strong enough to cause sunburn in just 11 minutes on a fine summers day. To prevent sun damage we recommend

following the Sun Smart steps: slip on clothing, slop on sunscreen, slap on a hat, slide on sunglasses and seek shade.

T H A N K Y O U

FOR PURCHASING A COOLAROO PRODUCT

When not in use, close the umbrella, place a protective cover over it and store in a dry place. If the canopy is wet, allow to dry naturally

opened up before storing.

If necessary, clean the fabric with a hose.

Components subject to turning and sliding can be treated with a non-staining lubricant spray (silicon-based).

CARE & MAINTENANCE

For help with product assembly or for any other questions you may have, contact our Customer Service Department.

Australia Toll Free: 1800 331 521New Zealand Toll Free: 0800 555 171United States Ph: +1 407 772 7900Middle East Ph: +971 4 881 7114China Ph: +86 574 5626 8888

WARNINGWhen assembling and using this product, safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use.

At least two or more people are recommended for safe assembly.

Keep all children and pets away from assembly area.

Install on level ground.

Check all nuts and bolts for tightness before and regularly during usage.

The base must be weighted down, fill with water to prevent tipping.

This is a non-permanent structure, do not use in extreme weather conditions including heavy rain or high winds.

Do not leave the umbrella open unattended.

Do not place the product near an open flame; or too close to any heat source.

The best under the sunCoolaroo is the leader in shade fabric technology. Our extensive range of attractive shade solutions is carefully manufactured to protect your home,

garden and family from the harsh sun.

coolaroo.com.au

Gale Pacific Limited 145 Woodlands Drive,Braeside, Victoria, 3195 Australia

Coolaroo is a registered trademark of Gale Pacific Limited

Attention: The schematics in this manual are for assembly and operation illustration only. They may differ from the umbrella’s actual appearance.

To register your product go to coolaroo.com.au. The product code can be found printed above the barcode on the product packaging, alternatively you can find it

on the relevant coolaroo.com.au product page.

430542/1505

A S S E M B L Y G U I D E

CANTILEVER UMBRELLAB A N K S I A

5YRWarranty A

GA

INST UV DEGRADATION

5 YE

AR FABRIC WARRANTY

122 Cremorne Street, Cremorne , Victoria 3121

t 03 9427 1286f 03 9427 1286w creativeresults.com.au

© Creative Results

Date 23/06/15 4:50 PM

Job / Version 13295 Coolaroo Cantilever Umbrella Instructions - Banksia A5 3d FINAL

Flat Size 443mm x 210mm

Finished Size 148mm x 210mm

Product Code 430542/1505

Barcode No.

Barcode Size

Print Process 4CP

Finished Artist

AnthonyHead of Creative

Account Manager

Client

Every effort has been made by

Creative Results to ensure this

artwork is correct. It is, however,

the client’s final responsibility

to check and sign off artwork

proofs or PDFs.

Creative Results will not be

responsible for any errors

approved by the client.

PROCESS4C

STEP 1 Take all parts out of boxes 1 and 2

and ensure they are all present.

Box 1a) Lower pole x 1

b) 360˚ Swivel system x 1

c) Screws x 4 (M8 x 15)

d) Screws x 4 (M8 x 25)

e) Washer x 8

f) Umbrella frame & canopy x 1

g) Crank handle x 1

h) Screw with plastic cap x 1

i) Plastic cover x 1

j) Plastic cone x 1

k) Allen key x 1

l) Umbrella cover x 1

m) Stay pole x 1

Box 2n) Fillable base and metal

cross base x 1

o) Base wheels x 4 (optional)

STEP 2Check that cross base pieces are secured to

the under side of (n).

Attach wheels (o) to the underside

of (n) (optional).

STEP 4Place the plastic cone (j) over the lower pole

(a) & position over 360° swivel system (b).

STEP 6Place the umbrella frame pole (f) onto the

lower pole (a). Push plastic cover (i) down to

sit neatly on plastic cone (j). Secure poles

together using the screw with plastic cap (h).

STEP 7Using the easy glide handle, push in an

upwards direction towards the top of

the umbrella pole until it locks into the

lowest position.

STEP 8Open the umbrella by inserting and

rotating the crank handle (g).

STEP 11To tilt the canopy horizontally, release the

lever on (f) as shown, then rotate to the left

or right and lock into position at desired angle.

2.82m/9'3"2.2m/7'3"

3.5m/11'6"

BANKSIA

A S S E M B L Y G U I D E

a

e

i

m

d

h

l

b

f

j

n

c

g

k

o

STEP 3Using screws (d) and washers (e) fix the

360° swivel system (b) onto the fillable

base (n). Then fix the lower pole (a) to

the 360° swivel system (b) using screws (c)

and remaining 4 washers (e).

Ensure canopy is closed when not in use. Close in windy conditions or when a storm approaches. Never allow the umbrella

to flap in the wind; this could damage the canopy. Do not use in extreme weather conditions including heavy rain or high winds.

The base must be filled with water to prevent the umbrella from tipping. This is a non permanent structure.

STEP 5Place the plastic cover (i) on the bottom

of the umbrella frame pole (f) as shown.i

f

j

ae

ed

c

n

b

f

i

ah

1

2

g

1 2

STEP 9Adjust the vertical angle of the umbrella,

by sliding the easy glide handle up the

pole and locking into desired position.

STEP 10The umbrella can be rotated 360° by

stepping on the foot pedal on the base.

1

2

2

1

n

o

STEP 1 Take all parts out of boxes 1 and 2

and ensure they are all present.

Box 1a) Lower pole x 1

b) 360˚ Swivel system x 1

c) Screws x 4 (M8 x 15)

d) Screws x 4 (M8 x 25)

e) Washer x 8

f) Umbrella frame & canopy x 1

g) Crank handle x 1

h) Screw with plastic cap x 1

i) Plastic cover x 1

j) Plastic cone x 1

k) Allen key x 1

l) Umbrella cover x 1

m) Stay pole x 1

Box 2n) Fillable base and metal

cross base x 1

o) Base wheels x 4 (optional)

STEP 2Check that cross base pieces are secured to

the under side of (n).

Attach wheels (o) to the underside

of (n) (optional).

STEP 4Place the plastic cone (j) over the lower pole

(a) & position over 360° swivel system (b).

STEP 6Place the umbrella frame pole (f) onto the

lower pole (a). Push plastic cover (i) down to

sit neatly on plastic cone (j). Secure poles

together using the screw with plastic cap (h).

STEP 7Using the easy glide handle, push in an

upwards direction towards the top of

the umbrella pole until it locks into the

lowest position.

STEP 8Open the umbrella by inserting and

rotating the crank handle (g).

STEP 11To tilt the canopy horizontally, release the

lever on (f) as shown, then rotate to the left

or right and lock into position at desired angle.

2.82m/9'3"2.2m/7'3"

3.5m/11'6"

BANKSIA

A S S E M B L Y G U I D E

a

e

i

m

d

h

l

b

f

j

n

c

g

k

o

STEP 3Using screws (d) and washers (e) fix the

360° swivel system (b) onto the fillable

base (n). Then fix the lower pole (a) to

the 360° swivel system (b) using screws (c)

and remaining 4 washers (e).

Ensure canopy is closed when not in use. Close in windy conditions or when a storm approaches. Never allow the umbrella

to flap in the wind; this could damage the canopy. Do not use in extreme weather conditions including heavy rain or high winds.

The base must be filled with water to prevent the umbrella from tipping. This is a non permanent structure.

STEP 5Place the plastic cover (i) on the bottom

of the umbrella frame pole (f) as shown.i

f

j

ae

ed

c

n

b

f

i

ah

1

2

g

1 2

STEP 9Adjust the vertical angle of the umbrella,

by sliding the easy glide handle up the

pole and locking into desired position.

STEP 10The umbrella can be rotated 360° by

stepping on the foot pedal on the base.

1

2

2

1

n

o

STEP 1 Take all parts out of boxes 1 and 2

and ensure they are all present.

Box 1a) Lower pole x 1

b) 360˚ Swivel system x 1

c) Screws x 4 (M8 x 15)

d) Screws x 4 (M8 x 25)

e) Washer x 8

f) Umbrella frame & canopy x 1

g) Crank handle x 1

h) Screw with plastic cap x 1

i) Plastic cover x 1

j) Plastic cone x 1

k) Allen key x 1

l) Umbrella cover x 1

m) Stay pole x 1

Box 2n) Fillable base and metal

cross base x 1

o) Base wheels x 4 (optional)

STEP 2Check that cross base pieces are secured to

the under side of (n).

Attach wheels (o) to the underside

of (n) (optional).

STEP 4Place the plastic cone (j) over the lower pole

(a) & position over 360° swivel system (b).

STEP 6Place the umbrella frame pole (f) onto the

lower pole (a). Push plastic cover (i) down to

sit neatly on plastic cone (j). Secure poles

together using the screw with plastic cap (h).

STEP 7Using the easy glide handle, push in an

upwards direction towards the top of

the umbrella pole until it locks into the

lowest position.

STEP 8Open the umbrella by inserting and

rotating the crank handle (g).

STEP 11To tilt the canopy horizontally, release the

lever on (f) as shown, then rotate to the left

or right and lock into position at desired angle.

2.82m/9'3"2.2m/7'3"

3.5m/11'6"

BANKSIA

A S S E M B L Y G U I D E

a

e

i

m

d

h

l

b

f

j

n

c

g

k

o

STEP 3Using screws (d) and washers (e) fix the

360° swivel system (b) onto the fillable

base (n). Then fix the lower pole (a) to

the 360° swivel system (b) using screws (c)

and remaining 4 washers (e).

Ensure canopy is closed when not in use. Close in windy conditions or when a storm approaches. Never allow the umbrella

to flap in the wind; this could damage the canopy. Do not use in extreme weather conditions including heavy rain or high winds.

The base must be filled with water to prevent the umbrella from tipping. This is a non permanent structure.

STEP 5Place the plastic cover (i) on the bottom

of the umbrella frame pole (f) as shown.i

f

j

ae

ed

c

n

b

f

i

ah

1

2

g

1 2

STEP 9Adjust the vertical angle of the umbrella,

by sliding the easy glide handle up the

pole and locking into desired position.

STEP 10The umbrella can be rotated 360° by

stepping on the foot pedal on the base.

1

2

2

1

n

o

Exposure to ultraviolet (UV) radiation from the sun is the major cause of skin cancer. In some countries the UV radiation

is strong enough to cause sunburn in just 11 minutes on a fine summers day. To prevent sun damage we recommend

following the Sun Smart steps: slip on clothing, slop on sunscreen, slap on a hat, slide on sunglasses and seek shade.

T H A N K Y O U

FOR PURCHASING A COOLAROO PRODUCT

When not in use, close the umbrella, place a protective cover over it and store in a dry place. If the canopy is wet, allow to dry naturally

opened up before storing.

If necessary, clean the fabric with a hose.

Components subject to turning and sliding can be treated with a non-staining lubricant spray (silicon-based).

CARE & MAINTENANCE

For help with product assembly or for any other questions you may have, contact our Customer Service Department.

Australia Toll Free: 1800 331 521New Zealand Toll Free: 0800 555 171United States Ph: +1 407 772 7900Middle East Ph: +971 4 881 7114China Ph: +86 574 5626 8888

WARNINGWhen assembling and using this product, safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use.

At least two or more people are recommended for safe assembly.

Keep all children and pets away from assembly area.

Install on level ground.

Check all nuts and bolts for tightness before and regularly during usage.

The base must be weighted down, fill with water to prevent tipping.

This is a non-permanent structure, do not use in extreme weather conditions including heavy rain or high winds.

Do not leave the umbrella open unattended.

Do not place the product near an open flame; or too close to any heat source.

The best under the sunCoolaroo is the leader in shade fabric technology. Our extensive range of attractive shade solutions is carefully manufactured to protect your home,

garden and family from the harsh sun.

coolaroo.com.au

Gale Pacific Limited 145 Woodlands Drive,Braeside, Victoria, 3195 Australia

Coolaroo is a registered trademark of Gale Pacific Limited

Attention: The schematics in this manual are for assembly and operation illustration only. They may differ from the umbrella’s actual appearance.

To register your product go to coolaroo.com.au. The product code can be found printed above the barcode on the product packaging, alternatively you can find it

on the relevant coolaroo.com.au product page.

430542/1505

A S S E M B L Y G U I D E

CANTILEVER UMBRELLAB A N K S I A

5YRWarranty A

GA

INST UV DEGRADATION

5 YE

AR FABRIC WARRANTY

122 Cremorne Street, Cremorne , Victoria 3121

t 03 9427 1286f 03 9427 1286w creativeresults.com.au

© Creative Results

Date 23/06/15 4:50 PM

Job / Version 13295 Coolaroo Cantilever Umbrella Instructions - Banksia A5 3d FINAL

Flat Size 443mm x 210mm

Finished Size 148mm x 210mm

Product Code 430542/1505

Barcode No.

Barcode Size

Print Process 4CP

Finished Artist

AnthonyHead of Creative

Account Manager

Client

Every effort has been made by

Creative Results to ensure this

artwork is correct. It is, however,

the client’s final responsibility

to check and sign off artwork

proofs or PDFs.

Creative Results will not be

responsible for any errors

approved by the client.

PROCESS4C

Exposure to ultraviolet (UV) radiation from the sun is the major cause of skin cancer. In some countries the UV radiation

is strong enough to cause sunburn in just 11 minutes on a fine summers day. To prevent sun damage we recommend

following the Sun Smart steps: slip on clothing, slop on sunscreen, slap on a hat, slide on sunglasses and seek shade.

T H A N K Y O U

FOR PURCHASING A COOLAROO PRODUCT

When not in use, close the umbrella, place a protective cover over it and store in a dry place. If the canopy is wet, allow to dry naturally

opened up before storing.

If necessary, clean the fabric with a hose.

Components subject to turning and sliding can be treated with a non-staining lubricant spray (silicon-based).

CARE & MAINTENANCE

For help with product assembly or for any other questions you may have, contact our Customer Service Department.

Australia Toll Free: 1800 331 521New Zealand Toll Free: 0800 555 171United States Ph: +1 407 772 7900Middle East Ph: +971 4 881 7114China Ph: +86 574 5626 8888

WARNINGWhen assembling and using this product, safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Please read all instructions before assembly and use.

At least two or more people are recommended for safe assembly.

Keep all children and pets away from assembly area.

Install on level ground.

Check all nuts and bolts for tightness before and regularly during usage.

The base must be weighted down, fill with water to prevent tipping.

This is a non-permanent structure, do not use in extreme weather conditions including heavy rain or high winds.

Do not leave the umbrella open unattended.

Do not place the product near an open flame; or too close to any heat source.

The best under the sunCoolaroo is the leader in shade fabric technology. Our extensive range of attractive shade solutions is carefully manufactured to protect your home,

garden and family from the harsh sun.

coolaroo.com.au

Gale Pacific Limited 145 Woodlands Drive,Braeside, Victoria, 3195 Australia

Coolaroo is a registered trademark of Gale Pacific Limited

Attention: The schematics in this manual are for assembly and operation illustration only. They may differ from the umbrella’s actual appearance.

To register your product go to coolaroo.com.au. The product code can be found printed above the barcode on the product packaging, alternatively you can find it

on the relevant coolaroo.com.au product page.

430542/1505

A S S E M B L Y G U I D E

CANTILEVER UMBRELLAB A N K S I A

5YRWarranty A

GA

INST UV DEGRADATION

5 YE

AR FABRIC WARRANTY

122 Cremorne Street, Cremorne , Victoria 3121

t 03 9427 1286f 03 9427 1286w creativeresults.com.au

© Creative Results

Date 23/06/15 4:50 PM

Job / Version 13295 Coolaroo Cantilever Umbrella Instructions - Banksia A5 3d FINAL

Flat Size 443mm x 210mm

Finished Size 148mm x 210mm

Product Code 430542/1505

Barcode No.

Barcode Size

Print Process 4CP

Finished Artist

AnthonyHead of Creative

Account Manager

Client

Every effort has been made by

Creative Results to ensure this

artwork is correct. It is, however,

the client’s final responsibility

to check and sign off artwork

proofs or PDFs.

Creative Results will not be

responsible for any errors

approved by the client.

PROCESS4C