pk-232sc operating manual - timewave technology inc. operating manual... · 2013-09-16 · 1 ....
TRANSCRIPT
1
PK-232SC Operating Manual
Note: This manual covers the features added with the SC version of the PK-232.
The main PK-232 manual describes the modes and features found in the original PK-232 and PK-232MBX. They are marked with an “*”. The DSP manual supplement describes the DSP board features.
2
WARRANTY TIMEWAVE TECHNOLOGY INC. LIMITED ONE YEAR WARRANTY
WHO IS COVERED This warranty is extended only to the original purchaser of the A.06118. WHAT WE WILL DO
If your A.06118 fails in normal use because of a defect in workmanship or materials within one year of the date of purchase, we will repair or replace (at our option) the equipment at our factory without charge to you. Timewave will pay for the return of the warranty-repaired unit to you.
WHAT YOU MUST DO
First, double check your connections and operating procedure. If you're certain that the unit is faulty, notify Timewave Customer Service immediately. If Timewave is unable to resolve the problem by telephone or email, we will give you an RMA number and ask you to return the unit. You must pay all shipping and insurance charges for returning the unit to our factory.
WHAT IS NOT COVERED
We cannot be responsible for damage caused by accidents, abuse, misuse, improper installation, or unauthorized attempts to repair the unit. This warranty does not cover any parts of the PK-232 except the A.06118.
SERVICE WARRANTY
Timewave service work performed in connection with this warranty is warranted to be free from defects in materials and workmanship for 30 days from the date of repair. All other terms of the limited warranty apply to the service warranty.
HOW TO CONTACT TIMEWAVE Contact Timewave Customer Service by telephone at (651) 489-5080 or by FAX at (651)
489-5066.
Mailing and shipping address is: 27 Empire Drive, Suite 110, St. Paul, MN 55103
email: [email protected] [email protected] [email protected] web: www.timewave.com
TIMEWAVE MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ©2001, 2005, 2011 by Timewave Technology Inc., St. Paul, MN USA
3
Table of Contents Overview ...................................................................................................................................... 4
PK-232SC Block Diagram ............................................................................................................. 5
Front Panel .................................................................................................................................. 6
Rear Panel .................................................................................................................................... 8
Operation .................................................................................................................................. 12
PC USB Connection .................................................................................................................... 12
USB device driver....................................................................................................................... 12
Power......................................................................................................................................... 12
Radio .......................................................................................................................................... 12
PK-232SC Ports .......................................................................................................................... 12
PK-232SC Control ....................................................................................................................... 13
Rig Control ................................................................................................................................. 13
USB Audio Sound Card .............................................................................................................. 13
SC Board Jumper Settings .......................................................................................................... 14
Data Sheet ................................................................................................................................. 15
4
Overview The PK-232SC is the latest generation of multimode data controllers built upon the solid foundation of the legendary PK-232. The PK-232SC features an expanded interface to connect and control your radio transceiver, station accessories and computer. The key to the new PK-232SC is a single USB cable from your PK-232SC to your computer. No other connection is necessary. Note the PK-232SC block diagram in Figure 1. The USB cable from the computer connects to a four port USB hub inside the PK-232. Port 1 of the USB hub connects to a dual USB-to-UART bridge. One of the UART serial ports connects directly to the PK-232SC UART serial port. This shows up on your computer as a standard COM port. Your software terminal program connects to this COM port to control the PK-232SC. The other UART serial port is the rig control port. This optically isolated port supports Icom CI-V, Yaesu CAT, Kenwood logic level, and RS-232 connections. This shows up on your computer as an enhanced COM port. Your software rig control program controls your transceiver. Port 2 of the USB hub connects to a USB Audio sound card inside the PK-232SC. The sound card audio is transformer isolated from the USB circuitry. The sound card/PK-232 switch or a software command selects either sound card transmit audio or PK-232SC transmit audio. Receive audio from your transceiver is always connected to both the sound card receive audio and the PK-232 receive audio. Ports 3 and 4 of the USB hub connect to a dual USB jack on the back panel of the PK-232SC. Use these jacks for rig control of USB-equipped transceivers and for other USB station accessories. A new feature in the PK-232SC is an instant reset switch. A quick flick of the switch when the power is off resets the PK-232SC to factory default condition.
5
PK-232SC Block Diagram
Radio XCVR
Computer
PK-232 CPU
System Block DiagramPK-232SCMultimode Controller
USBUSB-AudioSound Card
USB
Audio switching matrix
Data Audio
Rig control dataRig
Control
Serial Data
USB
Rig Control I/OSerial data
USBHub
USB
PTT, CW, FSK
Input
USBto
UARTx2
USB
Control
PK-232SC
PK-232 Modem Audio
SC Data Audio
Data Audio
PK-232 Data Audio
PK-232 PTT, CW, FSK Output
Aux USB Port
Aux USB Port
SC / TNCSwitch
SC / TNCSwitch
Figure 1
6
Front Panel
1. OVL LED 2. DCD LED* 3. THRESHOLD control* 4. TUNE LED bar* M – Mark S – Space 5. STATUS LEDs* 6. MODE LEDs* 7. RADIO 1 / RADIO 2 switch* 8. ON / OFF Power Switch* 9. SC LED 10. PK-232 LED 11. SC / PK-232 panel switch
1. Blue SC LED on – The SC mode is on if: a) the switch is set to left
OR b) Software has selected the SC mode (using SC command sequence)
1
2
3 4 5 6 7 8
9 10 11
7
2. Amber PK-232 LED on – The PK-232 mode is on if the switch is set to the right.
3. If both blue and amber LEDs are on at the same time, you have selected the SC mode with software control and have set the panel switch to PK-232 mode. The sound card mode (blue LED) is active if it is selected with either the panel switch or the software control. The software control will override the front panel switch PK-232 mode selection.
8
Rear Panel
1) Reset Resets PK-232 to factory default (baudot mode, erases memory) Press once momentarily with power off. 2) Power Power jack for +13.5 VDC @ 750 Ma. (5.5mm x 2.1mm) 3) RX-IN Audio 1* 3.5 mm mono phone jack
Tip – receive audio from radio Ring & Sleeve – Ground
4) Radio 1*
Five pin IDC flat connectors 1 – receive audio from radio 2 – transmit audio to radio 3 –Squelch 4 – Ground 5 – PTT
5) Radio 2*
Five pin IDC flat connector 1 – receive audio from radio 2 – transmit audio to radio 3 –Squelch 4 – Ground 5 – PTT Ring – ground/shield
3 4 5 6 7 8
1
2
10 11 12 13 14
15
16 17 18 19 22 21 20 24 23
9
9
6) RX-IN Audio 2* 3.5 mm mono phone jack
Tip – receive audio from radio Ring & Sleeve – Ground
7) Scope & FSK*
Five pin DIN connector 1 – FSK Normal output 2 – Ground 3 –Mark signal to oscilloscope 4 – FSK reverse output 5 – Space signal to oscilloscope
8) EXT Modem*
Five pin IDC flat connector 9) Key Out - *
Morse keying output to legacy transmitters with negative voltage on their Morse key inputs.
10) Key Out + * Morse keying output for newer transceivers and transmitters that use positive voltage on their Morse key inputs.
11) Aux Audio 3.5 mm stereo phone jack
Tip –Sound card audio out Ring 1 – Sound card audio in Ring 2 – ground/shield
Note 1 : Rig Control - 12), 13) & 18)
Appears as an enhanced COM port on PC. Connect only one of the three connectors at one time for proper RX/TX operation.
Exception: DTR connection from Logic Level port can be used with any RX/TX connection. Software determines function.
10
12) Logic Level Rig Control – See Note 1! 8 pin miniDIN female
1 – RXD - logic level data input from radio 2 – TXD - logic level data output to radio 3 – RTS – logic level data control output to radio 4 – CTS - logic level data control input from radio
5 – DTR – control output to radio from Rig Control COM port – use for PTT or positive CW keying – 30V/20mA MAX!
6 – Ground 7 - Short to pin 8 for older Kenwood logic level radios 8 - Short to pin 7 for older Kenwood logic level radios
13) CAT/CIV Rig Control – See Note 1! 3.5 mm stereo phone jack
Tip –RX logic level data input from radio Ring 1 – TX logic level data output to radio Ring 2 – ground/shield
14) PC USB Five pin USB miniB Connect to PC USB port 15) AFSK Out Level
PK-232 Transmit data audio level adjustment 16) SC LED
Upgrade devices only – LED on indicates the sound card mode is selected. 17) SC /TNC switch
Upgrade devices only – switches between sound card and PK-232 modems. 18) RS-232 rig control – See Note 1! DB-9 male 1 - NC 2 -RX 3 - TX 4 - NC 5 - Ground 6 - NC 7 – RTS 8 - CTS 9 - NC
11
19) Aux Out Level Adjusts only sound card auxiliary output level
20) USBx2
Two USB Type B jacks for USB 2.0 compatible devices. Maximum 100 mA. each unless 5VDC power supply is connected.
21) +5VDC ONLY!
Do not connect any other voltage to this jack! Center of jack is positive polarity. 5 Volts DC only @ 2A for powered USB hub operation only Required only for USB devices that draw greater than 100 mA. To use this jack, you must change a jumper inside the PK-232SC.
22) Aux in Level
Adjusts only sound card auxiliary input level 23) SC TX level Adjusts only sound card output level 24) SC RX level Adjusts only sound card input level
12
Operation Note: This manual covers the features added with the SC version of the PK-232.
The main PK-232 manual describes the modes and features found in the original PK-232 and PK-232MBX. The DSP manual supplement describes the DSP board features.
PC USB Connection Connect the PK-232SC to an USB 2.0 compatible port on a computer with a single USB cable (USB miniB to USB A). No other computer connections are required. The computer USB port must be capable of supplying full USB power (5.0 Volts @ 500mA.) If a USB hub is used, it must be a powered hub.
USB device driver The device drivers for Windows XP/VISTA/7 will load automatically when the PK-232SC is connected to your Windows PC if it is connected to the internet. The drivers are also found on the CD distributed with the PK-232SC and on the Timewave web site (www.timewave.com.) Other drivers are available for Linux and Apple computers. Please contact Timewave or visit the Timewave website for further information. Note: This device driver is different from previous PK-232/USB device drivers. The older drivers will not work for the PK-232SC.
Power Connect the PK-232SC to a +13VDC @ 750 mA. power supply. Press the PK-232SC power switch to the IN position. This connection is the same for all models of the PK-232.
Radio Connect your radio data audio input, data audio output and PTT line to the PK-232SC Radio 1 or Radio 2 ports. This connection is the same for all models of the PK-232. If you are upgrading your PK-232MBX to a PK-232SC, you can use your existing cable if you do not change radios. This connection is the same for all models of the PK-232.
PK-232SC Ports The PK-232Sc has two COM ports, a USB Audio sound card port and 2 USB ports.
The PK-232 terminal program uses the “standard” COM port to control the PK-232SC operation.
The PK-232SC rig control program uses the “enhanced” COM port to control your transceiver.
The PK-232SC sound card mode programs use the “USB Audio Codec” to run sound card programs.
The PK-232SC USB ports appear on your computer USB port list and can be used for USB 2.0
compatible USB devices.
13
Some programs will automatically identify the correct ports for their functions. Others may have limited ability to aid you in connecting the correct port to your software application. If you wish to identify or edit the various PK-232SC ports, use the Device Manager application found in Windows XP/VISTA/Win7. Go to Control Panel/System or Computer/properties to find Device Manager. You should learn to use Device Manager to help you understand and manage the hardware configuration of your PC for all your devices and programs.
PK-232SC Control The PK-232 terminal program uses the “standard” COM port to control the PK-232SC operation. You can use a variety of programs to control the PK-232SC A “dumb” terminal program such as Hyperterminal (Windows XP) or puTTY allows you to control the PK-232SC in command mode. There is little or no automation so all commands must be entered manually. Some programs have macros that let you create commands by stringing together a series of commands that can be sent with one or two keystrokes. Other programs offer complete control of the PK-232SC with standard Windows graphical commands, mouse actions and keystrokes. If you need a program with complete PK-232SC support, Timewave recommends Radio Operating Center (ROC) from W4PC Software, Inc. (www.w4pcsoftware.com). We suggest you contact the author of your favorite program to determine its level of PK-232SC support. Timewave has a free applet called “ModemSwitch” (www.timewave.com.download.html that will switch the PK-232 from transmit to receive and from sound card to PK-232 mode. It also has a simple dumb terminal program for testing the PK-232.
Rig Control Connect your radio rig control port to the matching PK-232SC CAT/CIV, 8 pin miniDIN, or RS-232 connector. Only one of the three connectors may be connected at one time. You may also connect one of the two USB connectors to your radio if it supports USB rig control. Rig control is a connection for the PK-232SC only. Earlier models of the PK-232 do not have this connection. Timewave has several standard rig control cables for popular models of radios. We can supply a cable for any compatible radio. Please contact us for details. Your rig control software and your radio determine your rig control operating features. The PK-232SC rig control circuitry is an interface only and does not affect the actual rig control operation. Timewave recommends Radio Operating Center (ROC) from W4PC Software, Inc. (www.w4pcsoftware.com) and Ham Radio Deluxe (www.ham-radio-deluxe.com) for rig control. The PK-232SC operating COM port and the PK-232SC rig control COM port are independent. You can use different PK-232SC operating and rig control programs simultaneously. For example, you may use Ham Radio Deluxe for rig control and ROC for operating a PK-232SC mode such as Pactor.
USB Audio Sound Card The USB audio sound card built into the PK-232SC appears as a separate audio device on your PC. It is called “USB Audio Codec”. No software driver is necessary when you use the USB Audio Codec. You must select the USB Audio Codec when you configure your terminal program to operate sound card modes such as PSK-31. Use the program settings window in Radio Operating Center or the soundcard settings in Digital Master 780 found in Ham Radio Deluxe.
14
SC Board Jumper Settings The SC board has several jumper options that may be changed by the user. In most instances the jumpers can be left at the factory default settings. The jumpers are located on the SC daughter board at the rear of the PK-SC. Rig Control Not all transceivers have the same polarity settings for their logic level rig control ports. The PK-232SC polarity settings for RX, TX, RTS and CTS can be changed to meet the requirements of any specific transceiver. The factory default settings for JP1 (RX), JP2 (TX), JP3(RTS) and JP4(CTS) are pins 1& 2 connected. Connecting pins 2 & 3 will invert the polarity for one line only. Change these settings only if you cannot your rig control program to recognize your transceiver. Most transceivers will not require any change! USB Jack Power The two type B USB jacks on the PK-232SC default power output is 5 Volts @ 100 mA. This power is derived from the computer or powered USB hub upstream from the PK-232SC. If the jumper on JP5 is connected between pins 2 &3 (factory default), the external power supply will not be connected. The USB circuitry will draw its power from the upstream USB device. If you want to draw more than 100 mA. (500mA. max) from the PK-232 USB hub ports, you may connect a 5.0 VDC @ 2A power supply to the PK-232. To do so you must enable the 5.0VDC power jack in the middle of the PK-232SC back panel. Change the jumper on JP5 to pins 1 & 2. With the jumper in this position, you must use the 5.0 VDC power supply so the USB circuitry will work! USB Audio Sound Card Channel Combinations The USB Audio sound card has two channels. Receive Audio Input In the factory default mode, the PK-232 sound card input (receive audio) is fed to both channels simultaneously. Connecting JP23 pins 1 & 2 enables the factory default combined channel mode. In optional mode, the PK-232 sound card input (receive audio) is fed to the left sound card channel and the Aux Audio input (J10-ring on the SC connector board) is fed to the right sound card channel. Connecting JP23 pins 2 & 3 enables the optional split channel mode. Transmit Audio In the factory default mode, both USB Audio sound card output channels feed the PK-232 sound card output (transmit audio) simultaneously. Connecting JP3 pins 1 & 2 enables the factory default combined channel mode. In optional mode, the left sound card channel feeds PK-232 sound card output (transmit audio) and the right sound card channel feeds the Aux Audio output (J10-tip) on the SC connector board.) Connecting JP2 pins 2 & 3 enables the optional split channel mode.
15
Data Sheet
PK-232SC Multimode Data Controller Now with USB Audio, Rig Control and Single USB Computer Cable! Features Digital Signal Processor 18 DSP Filters Twin Peak RTTY Filters Adaptive PACTOR filters Works with all sound card modes USB Sound Card Audio RS-232, logic level & USB Rig Control for Icom, Yaesu & Kenwood radios Single USB Computer Connection Galvanic Computer Isolation SC Upgrades for all PK-232 models
Timewave’s customers swear by their DSP filters and PK-232 owners love the flexibility and reliability of the most popular data controller ever built. Now with the addition of a built-in sound card, rig control, computer isolation and total USB connectivity, the PK-232SC rolls it all into one! The PK-232SC brings a new level of performance to the legendary PK-232 with sharp, accurate DSP filters for all its internal data modes and dual transformer isolation for sound card data modes. Weak signals magically appear from the noise and QRM bounces off the new DSP filters for cleaner copy with fewer errors than the old analog filters.
More Filters, Better Filters, Automatic selection The PK-232SC brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232SC is compatible with all Windows XP, Vista, and Windows 7 software terminal programs for the PK-232.
Sound Card Interface and Rig Control For maximum flexibility, Sound Card / TNC switching is both software and panel switch controlled. The sound card mode selection is software controlled. For example, when operating with Radio Operating Center software, changing to PSK31 from Pactor or MT63 is a simple menu click. The single USB cable from your PC also moves your logic level Kenwood RX/TX/RTS/CTS, Yaesu CAT, and Icom CIV, RS-232 and USB Rig Control interface to the back panel of your PK-232SC.
16
All the Proven Modes + All the Sound Card Modes The PK-232SC supports all the new sound card modes in addition to all of the existing PK-232 modes - Pactor, VHF/HF Packet, AMTOR/SITOR, Baudot, ASCII, Morse, HF Weather FAX, TDM, and NAVTEX. The PK-232SC comes with a complete cable and connector set in addition to Timewave’s on-line and telephone support. As always, you can upgrade any PK-232 ever built to the latest PK-232SC!
Specifications for the PK-232SC DSP Filters, demodulator 16 bit Analog Devices 2104 with 16 bit A/D-D/A for Optimum filters for each mode, limiter, 4-pole discriminator, 5-pole post-
detection low-pass filter
Modulator Phase continuous sinewave, AFSK generator
Modulator output level 5-200 mV RMS
Processor system Zilog Z-80, ADSP2105
Memory 32K Lithium battery-backed RAM, 128k ROM
Audio Internal USB Audio sound card
Hardware HDLC Zilog 85C30 SCC
Power requirements +13 to +16 VDC @ 590 mA.
Input/Output Connections Radio interface Two 5-pin connectors, front panel selectable
Direct FSK outputs Normal/Reverse
Scope outputs Mark, space
CW keying outputs +100 VDC @ 200 mA max and –25 VDC @ 30 mA max
Terminal interface USB (galvanic isolation from PK-232 circuitry)
Terminal data rates Autobaud settings at 2400, 4800, & 9600 bps
Rig Control interface Yaesu CAT, Icom CIV, Kenwood TX/RX/RTS/CTS logic level, RS-232, USB
USB Downstream Ports Two USB 2.0, 100mA each (500 mA option available)
USB Computer Port USB mini-B jack
Physical Dimensions 11" (279mm)W x 8.25" (210mm)D x 2.5" (64mm)H
Weight 3 lbs (1.35 kg)
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
VBUS_DET
OCS_n[2:1]
OCS_n1OCS_n2
OCS_n2
LOCAL_PWR
RESETn
OCS_n1
VDDA18PLL
VDDA33
PRTPWR3
PRTPWR4
OCS_n4OCS_n3
PRTPWR1
PRTPWR1
PRTPWR2
PRTPWR[2:1]
PRTPWR4PRTPWR3
PRTPWR2
OCS_n3
OCS_n4
+3.3Vu
+3.3Vu
+3.3Vu
+3.3Vu
+3.3Vu
GND
VBUS2-SW
GND
CP2105-D-
VBUS1-SW
CP2105-D+
GND-USB
PCM2901-D+
PCM2901-D-
USB2514-CLKIN-24MHz
Title
Size Document Number R ev
Date: Sheet o f
<Doc> 12-4.1
PK-232SC USB Hub
C
1 5Wednesday, September 14, 2011
Active HubIndicatorOptionalfor production
Optional for production
To program U10 flash memory - Place shunts on pins 2 & 3 of JP7, JP10 and JP17.
For operation from flash memory -Place shunts on pins 1 & 2 of JP7, JP10, and JP17.
For USB 2512 default, remove all shunts
SCL
SDA
SDA
SCL
GND_UP
VBUS_UP
USBUP_DP_H
USBUP_DM_H
Rig Control
PK-232
Audio
SDASCLGND
ProgramFlash Mem
Flash MemProgram
ProgrammerConnector
Upstream
USB UpstreamTo SC Conn board
USBDN_DP3
USBDN_DP4
USBDN_DM3
USBDN_DM4
PWR3
PWR4
PWR3
PWR4USBDN_DP4
USBDN_DM4
USBDN_DP3
USBDN_DM3
US
B 2
bot
tom
Bac
k Pa
nel
USBDN_DP4
USBDN_DM4
USBDN_DP3
USBDN_DM3
US
B 1
top
- B
ack
Pan
el
PWR3
PWR4
VBUS_UP
PWR1
USBDN_DP1_H
USBDN_DM1_H
USBDN_DP2_H
USBDN_DM2_H
PWR2
USBDN_DP1
USBDN_DM1
USBDN_DP2
USBDN_DM2
PWR1
PWR2
USBUP_DP
USBUP_DM
SDA
Do Not Stuff!
Upstream
Downstream 1
Downstream 2
Downstream 3
Downstream 4
EEPROM/Config
Common
U3USB2514QFN36
USBUP_DP 31
USBUP_DM 30
USBDN1_DP 2
USBDN2_DP 4
USBDN3_DP 7
USBDN4_DP 9
USBDN1_DM 1
USBDN2_DM 3
USBDN3_DM 6
USBDN4_DM 8
VBUS_DET27
PRTPWR1 12
PRTPWR2 16
PRTPWR3 18
PRTPWR4 20
OCS113
OCS217
OCS319
OCS421
RBIAS 35
SDA/SMBDATA/NON_REM1 22SCL/SMBCLK/CFG_SEL0 24
HS_IND/CFG_SEL1 25
XTAL1/CLKIN33
XTAL232
RESET26
LOCAL_PWR/NON_REM0/SUSP_IND_N28
TEST11
VDD33(IO) 23
VDDPLL18 34
VDDA33 29VDDPLLREF/VDDA33 36
VDD33(REG) 15
VDDCR18 14
VSS(FLAG)37
VDDA33 5VDDA33 10
U1 LP38501-ADJ
IN2
GN
D3
EN1 ADJ 5
OUT 4
C10 0.1uF
J6HEADER_4
1234
C29
0.1uF
C23
0.1uF
LED3RED
JP3Header 3
123
R9 0
C24
0.1uF
+ C6
100uF
JP4Header 3
123
R6100K
C25
0.1uF
J5 +5Vu
1
C3
1nF
BR2BGX50A
31
2 4
R13 0
R15100K
+ C110uF
R10 0
L2
DLP11SN900SL2
12
3 4
LED2 GRN
C13 0.1uF
BR1BGX50A
31
2 4
JP1
JUMPER 2_7
12
C4
33pF
JP5Header 3
123
C18
0.1uF
U2MIC2026-1BM
IN7
ENA1 OUTA 8OUTB 5
FLAGA 2
ENB4
GND6
FLAGB 3
+C2100uF
FB2
2A/0.05DCR
R14100K
R20100K
C28
1.0uF/10V
C16
0.1uF
R7
100K
R11 0
JP2
JUMPER 3
123
U4MIC2026-1BM
IN7
ENA1 OUTA 8OUTB 5
FLAGA 2
ENB4
GND6
FLAGB 3
C15
0.1uF
US
B D
UA
L-A
-RE
C-R
A-T
HR
U
J3
VCC1T
D-2T
D+3T
GND4T
SHLD9
SHLD10
VCC1B
D+3B
D-2B
GND4B
SHLD11
SHLD12
+ C8
100uF
J11
2
3
LED1 GRN
R1812.0K1%
C27
0.1uF
C194.7uF/6.3V
R510k
C9
0.1uF
U5 AT24C02C-TH
A01A12A23
WP7
SCL6
SDA 5
VCC 8
GND 4
C7
0.1uF
J2
HEADER_4
1234
C22
0.1uF
R16100K
+ C11
100uF
FB1
2A/0.05DCR
R12 0
R244.2k
R1 330
R8 0
J4
HEADER_4
1234
R19 1K
R310k
L1
DLP11SN900SL2
12
3 4
C30
1.0uF/10V
+ C14
100uF
C12
0.1uF
C170.1uF
R17100K
C51nF
C20
0.1uF
R4 330
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
+5Vi
+3.3VA
+5AVref
+3.3V
+3.3Vu+3.3Vu
GND-USB
VBUS2-SW
USB2514-CLKIN-24MHz
PCM2901-CLKIN-12MHz
Title
Size Document Number R ev
Date: Sheet o f
<Doc> 12-4.1
Power Supply & Reset
C
2 5Wednesday, September 14, 2011
4/19/2011
Reset Switch Assembly Jack
To PK-232sc +13.5 VDC
To USB audio codec
To isolated +5Vi digital circuits including 74xx ICs
From VBUS Audio
To isolated +5VA Analog circuits+2.5VDC audio reference
USB audio circuits
12.0 MHz
24.0 MHz To USB2514 clk in
To PCM2901clk in
C26.01uF
C460.1uF
R2310k
C420.1uF
R92 0
C501.0uF/10V
U29 74AUP1G74
D2
CLK1
Q 5
Q3
VCC 8
PRE 7
GND4
CLR 6
R158 0
+C3610uF
C370.1uF
R159 0
C49.01uF
C321.0uF/10V
+ C35100uF
C33.01uF
U6 LP38692MP-3.3
Ven1 NC 2Vout 3Vin4
GN
D5
R220
C311.0uF/10V
JP7Header 2
12
JP6Header 2
12
U7LM7805CT
IN1 OUT 3
GN
D2
U27
FXO-HC735-24MHZ
VCC4
EN1
OUT 3
GND 2
+ C111100uF
C410.1uF
C48.01uF
R21 10k
+ C110100uF
D1S1GB
1 2R150 0
C21.01uF
R134 10k
C341nF
U10 LP38692MP-2.5
Ven1 NC 2Vout 3Vin4
GN
D5
+ C44100uFC45
0.1uF
L3
BEAD FERRITE/SM
U9LM7805CT
IN1 OUT 3
GN
D2
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
+5Vi
+5Vi
+3.3Vu
+3.3Vu
+3.3Vu
+3.3Vu
+3.3Vu
+5Vi
+5Vi +3.3Vu
+3.3Vu+3.3Vu
+3.3Vu
GND-USB
VBUS1-SW
CP2105-D+
CP2105-D-
GND
DTR-PK232
TX
RX
RTS
CTS
DTR
Title
Size Document Number R ev
Date: Sheet o f
<Doc> 12-4.1
PK-232 USB- UART & Rig Control
C
3 5Monday, October 31, 2011
RTS
TXD/
CTS
DCDB/ U19-8
RXDB U19-3CTSB/ U19-11
RXD/
RXD/
CTS
TXD/
RTS
DTRB/ U20-9,10
TXDB U20-4,5RTSB U20-12,13
To PK-232 U7 8530Remove U19, U20solder wires to U19, U20 pins
DCDB/ U19-8RXDB U19-3CTSB/ U19-11
DTRB/ U20-9,10TXDB U20-4,5RTSB U20-12,13
U19-5
U19-6U19-7
Connect 2N3904 for PK-232 only!Do not use for PK-232MBX and all Timewave models
RI
DTR
DCD DCD
TXD
/RTS
/CTS
Rig Control
RTS
CTS
GND
TXD/
TX
RX
TX
RX
DTR
Rig Control - DTR - Aux OutTo SC Conn board
RXD-KW
RX
TX
CTS
RTS
RX
CTS
Rig Control -Kenwood sensing pinsTo SC Conn board
DTR
CTS
Do Not Stuff!
RX
CTS
TXRTS
R7410k
R27 470
R39Open
R76 10
R64 150
R75 150
R33470
R61 Open
C1050.1uF
U11PS2801C-4
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
R135100k
JP11TX
123
R70150
JP9 HEADER 3
123
R44Open
C641nF
U17B74LVC86/SO
64
5
147
R73100k
R31 470
C1060.1uF
U26 open
1
2
4
3
+ C534.7uF/6.3V
R24 470
R13610k
U18 PS2801C-1-F3-A
1
2
4
3
J7
12
JP12 RTS
123
C380.1uF
C1070.1uF
U14D74LVC86/SO
1112
1314
7
R62 10k
R38Open
U17D74LVC86/SO
1112
13
147
R34470
R137 open
R3610k
JP13 RX
123
R55 150
R67Open
R29470
R69150
R138open
R43Open
R3547k
R37Open
R324.7k
C520.1uF
R48Open
JP14 CTS
123
U14A74LVC86/SO
31
2
147
R56470
R28470
U12 74HC7541
OE11
GN
D10
OE219
VC
C20
A02A13A24A35A46A57A68A79
Y0 18Y1 17Y2 16Y3 15Y4 14Y5 13Y6 12Y7 11
R68 10k
C541.0uF/10V
U13
CP2105
Vio5
REGIN7
VDD6
GND2
VBUS8
D+3
D-4
/RST 9
/Suspend-RIe 17
Vpp-DCDe 16
GPIO.1-DTRe 15
RTSe 11
TXDe 13
CTSe 10
RXDe 12
RXDs 20
TXDs 21
RTSs 19
CTSs 18
GPIO.1-DSRe 14
GPIO.1-DTRs 23
GPIO.0-DCDs 24
/Suspend-RIs 1
GPIO.2-DSRs 22
U14B 74LVC86/SO
64
5
147
R4610k
R4710k
R42Open
R57470
R30 560
U17A
74LVC86/SO
31
2
147
JP8 HEADER 3
123
R52 Open
+C51
4.7uF/6.3V
R26 470
JP10 HEADER 3
123
U17C74LVC86/SO
89
10
147
C1030.1uF
C109open
Q1MMBT2222A
R41Open
R4547k
R40Open
R2547k
R5110k
U14C74LVC86/SO
89
10
147
C631nF
R6047k
R49 150
U15PS2801C-4
1
2
3
4
5
6
7
8 9
10
11
12
13
14
15
16
C470.1uF
R63 150
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
+5Vi
+5Vi
+5Vi
DTR
TX
RX
RTS
CTS
Title
Size Document Number R ev
Date: Sheet o f
<Doc> 12-4.1
RS-232/Logic Rig Control
C
4 5Wednesday, September 14, 2011
TX
RTS
Rig Control - DTR - Aux OutDTR
TX
RX
RTS
CTS
RX
RX
TX
DTR
CTS
RTS
RX-232
TX-232RTS-232
CTS-232DTR-232
CTS CTS-232RX-232
TX-232RTS-232
TXRTS
CTS
RX
Rig Control
RX
CTS
DTR
TXRX
Do Not Stuff!
Rig Control To SC Conn board
RTSCTS
GND
R14922
R7110
R5347
C1151nF
R8010k
C5747pF
MAX3223CPWU33
DIN113
RIN2 9RIN1 16
C2-6
C2+5
DOUT2 8DOUT1 17
V- 7
V+ 3
GN
D18
FORCEON 14
INVALID_L 11
EN_L 1
C1-4
C1+2
FORCEOFF_L 20
ROUT210ROUT115
VC
C19
DIN212
C124 0.1uF
R7210
C5547pF
R144332
C1161nF
P2
DB9M-RA
594837261
10
C1250.1uF
C1171nF
C621nF
C601nF
J8
HEADER_6
123456
U32B74AHCT125
56
1447
R15110k
R6647
C6147pF
R15310k
R152Open
C119
0.1uF
R5847
R6547
U32C74AHCT125
98
14107
R15410k
R14622
C1200.1uF
C5947pF
R5947
R14722
C1210.1uF
C561nF
U32A74AHCT125
23
1417
C113.01uF
U32D74AHCT125
1211
14137
R14822
U3474AHC1G04/SOT
245
3
C581nF
C1220.1uF
R5447
C126 0.1uF
C1141nF
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
+3.3V
+3.3V
+3.3VA
+3.3V
+3.3VA
+3.3VA
+3.3VA
Vref
Vref
+5A
+5A
+5A
Vref
Vref+5A
+5A
+5A
+5A
GND
PCM2901-D+
VBUS2-SW
PCM2901-D-
GND-USB
DTR-PK232
PCM2901-CLKIN-12MHz
Title
Size Document Number R ev
Date: Sheet o f
<Doc> 12-4.1
USB Audio & SC/TNC Switch
C
5 5Monday, October 31, 2011
SC TX Data Audio Out L
Volume Down
Volume up
Mute
SC RX Data Audio Out L
PCM2901 SC Audio Input L
Sound Card Audio Out Level Adjust
C59 (R160) from PK-232 TX Audio Out(Remove R160)
R160/SW2 to TX Audio In
SW2 is Radio 1 / Radio 2 Switch
SC RX input audioC54/SW2 from RX Audio out
SW2 is Radio 1 / Radio 2 Switch
R34/C54 to PK-232 Audio IN ORDSP Audio IN (if installed)
DSP Cap bypass.Short if DSP is installed
R149 - Q6 from PK-232Sound Card / TNC Switch
PK-232 PanelSound Card / TNCToggle Switch
Aux Audio Out R
Aux Audio In R
Aux Audio In R
To Connector Board
PK-232 Panel LEDSound Card / TNC
Aux Audio Out R
1-2 L+R combined (default)2-3 L+R split
1-2 L+R combined (default)2-3 L+R split
R1401k
+
C7510uF/6.3V
R130100
R12610
R11810k
+
C79 10uF
R1211k
R9812.0k
R109 0
J10
HEADER_4
1234
R1053.9k
R911.5k
+
C9110uF
+C68
4.7uF/6.3V
R122open
R93 Open
C1080.1uF
C101.01uF
+
C7610uF
R11347
R12310k
R156 10k
J9
HEADER 3
123
R12410k
R8920k
-
+
U23A
AD8656
3
21
84
C1281nF
VDD
GND
S 1
S 2U25
ADG749BKSZ
1
4
65
23
R1391k
R941.0M
JP16Header 4x1_2
1234
R128500
R95100
R10612.0k
R1193.3k
+
C9510uF
R12910k
C880.1uF
+ C67100uF
R157 10k
C96.01uF
R7920k
C851800pF
R133Open
R127open
+ C7810uF/6.3V
C74 330pF
+
C99
10uF
T1600:600
1 6
5
3 4
78
C710.1uF
T2
600:600
1 6
5
3 4
78
+
C8010uF
C83 330pF
R102 open
C82.01uF
R114OPEN
C811800pF
JP21Header 2
12
-
+
U24BAD8656
5
67
C98 22pf
R11710k
Q42N7002
C112
47pF
U1974LVC1G08/SOT
OUT 4IN22
IN11 VDD
5
GND
3
C123 22pF
C89 330pF
JP19Header 2
12
-
+
U23BAD8656
5
67
R84500
13
2
R821.5k
R132 1000
-
+
U22BAD8656
5
67
R11610k
R111500
R874.7k
+
C65 10uF
R7847k
C931800pF
D31N4148
R1080
JP20JUMPER 3
123
+
C77
10uF
+
C9410uF
+
C8710uF
C97 22pF
C102.01uF
Q3open
JP18Header 2
12
-
+
U24AAD8656
3
21
84
+ C7310uF/6.3V
R104100
R12510k
JP17JUMPER 3
123
R99 12.0k
R770
R11510k
U20
TPA6111A2
VD
D8
GN
D4
VO1 1
VO2 7
BPAS3
SDN5
IN12
IN26
R11010k
R8147k
U21 PCM2901E
D+1
D-2
Vbus3
DGNDU4
HID05
HID16
HID27
SEL08
SEL19
Vccc10
AGNDC11
VinL12
VinR13
Vcom14
SSPND 28
Vdd 27
DGND 26
TEST1 25
TEST0 24
Vccx 23
AGNDX 22
XTI 21
XTO 20
Vccp2 19
AGNDP 18
Vccp1 17
VoutL 16
VoutR 15
-
+
U22AAD8656
3
21
84
JP23 JUMPER 3
1 2 3
R86 22
+ C8410uF/6.3V
+
C92
10uF
R965k
D21N4148
LED4RED
R90 12.0k
R14310k
+ C6910uF/6.3V
R1013.9k
R8510k
C700.1uF
C90.01uF
+
C100
10uF
R10710k
C72.01uF
+ C8610uF/6.3V
C127CAP
Q22N7002
R12010k
R142 0
+
C66 100uF
R88 22
R973.9k
R11247
R103 12.0k
R141 0
R13147
JP15
Header 2
12
R10012.0k
R8315k
R155 10k
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
VBUS_UP_H
GND_UP
USBUP_DM_H
VBUS_UP
USBUP_DP_H
Title
Size Document Number R ev
Date: Sheet o f
<Doc> 12-1
PK-232SC Connector PCB
C
1 1Tuesday, November 15, 2011
USB UPSTREAM
Rig Control I/O 1 Logic
GND_UP
VBUS_UP
USB_DP_H
Rig Control CIV/CAT only
Rig Control - Kenwood only
RTSCTS
TXDRXD
GND
USB_DM_H
Audio MonitorTip - OutputRing - Input
Rig Control I/O 2 Logic with RTS/CTS
AudioR-OutAudioR-IN
GND-PCM2901
Rig Control + DTR - Aux OutTo SC Conn board
USB UpstreamTo SC Conn board
Rig GND test point
PK-232 GND test point
Rig Control -Kenwood sensing pinsJumper pins 7 & 8 forKenwood rig control
DTR
TXD
RXD
Rig Control -Kenwood sensing pinsTo SC Conn board
Tip - RXD InputRing - TXD Output
C12 0.1uF
C61nF
J1
mini-USB B
VCC1D-2D+3ID4GND5S16S27S38S49
C101nF
J6
HEADER_6
123456
FB2 2A/0.05DCR
J5 HEADER 2
12
J3 HEADER 1
1
R5 22
L1DLP11SN900SL2
12
3 4
J2 HEADER_4
1234
C51nF
R9open
J10
3.5mm
R7 22
C111nF
C1 1nF
C71nF
C30.1uF
BR1BGX50A
31
2 4
C141nF
C41nF
J9 HEADER 3
123
R10open
J4
3.5mm
C81nF
R6 330
R2 22
R1330
C131nF
R8 22
FB1 2A/0.05DCR
C91nF
R4 22
R3 22
J7
MDIN-8-R-Sh
1
34 5
678
2
9 10 11
J8 HEADER 1
1
C2
1nF
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
Title
Size Document Number Rev
Date: Sheet o f
A.xxxxx 1
PK-232 Reset Switch Assembly
A
1 1Wednesday, July 20, 2011
Wire to +5BB - D12 or D14
To JP1 on PK-232 main board
Wire to Ground
Wire to +5BB - D12 or D14
To JP1 on PK-232 main board
nc
Reset Switch AssemblyAll wires #24 vinyl covered
To JP7-1 PK-232SC board
Assembly for PK-232SC board
Assembly for all PK-232 models without SC board
To reset PK-232 to factory default, Press switch for 1 sec with power off
R110k
J72 Pin IDC
12
J62 Pin IDC
12
SW1SW DPDT - Momentary
J12 Pin IDC
12
SW1SW DPDT - Momentary
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
Title
Size Document Number Rev
Date: Sheet o f
MPCB.40733 <RevCode>
SC/TNC LED-Switch board
A
1 1Monday, June 06, 2011
TNC Sound Card
TNC Sound Card
Assembly AP.40734
R11k
D2Yellow
21
SW1SW SPDT
D1Blue
21
JP1
Header 4x1_2
1234