Tel: 01773 764288 E-mail: sales@phaseprint.com www.phaseprint.com

E X C L U S I V E T O

We are continually improving and modifying our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE.

P R O D U C T S P E C I F I C A T I O N …

ComLiteG R A P H I C S D I S P L A Y S Y S T E M STEAR DROP FLAG

A lightweight ultra portable flag system with quality carbon fibre parts making the unit durable and strong.

FEATURES & BENEFITS:

• High strength sectional carbon fibre pole• 3 flag sizes small, medium and large.• Market leading quality and performance• Printed flags in single-sided fabric• Choice of base unit accessories available• As standard our flags are supplied with printed, non-elasticated ‘wrap-

around’ pole sleeves• Design templates are available to set artwork to our requirement.

HARDWARE SPECIFICATIONS:

Overall Height (mm):

2250mm Small3340mm Medium4925mm Large

Weight:

4kg (does not include weight of base)

GRAPHICS SPECIFICATIONS:

Recommended Graphic Dimensions:

1990 (h) x 803 (w) approx Small3060 (h) x 1059 (w) approx Medium4050 (h) x 1157 (w) approx Large

Substrate:

Printed on single sided flag material.

ADDITIONAL:

Included in kit:

Carry Bag, Pole, Graphic.

Extras:

Spike, Cross base, Car Foot, Water Base, Concrete Base.

* Illustration only - Actual products may differ in style. Please note that you must select the kind of base you require when enquiring.

Tel: 01773 764288 E-mail: sales@phaseprint.com www.phaseprint.com

E X C L U S I V E T O

We are continually improving and modifying our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE.

ComLiteG R A P H I C S D I S P L A Y S Y S T E M S

P R O D U C T I N S T R U C T I O N S …

i) Lay your Flag flat.

ii) Insert the thinnest Pole section protected end first into the Flag

sleeve.

Draw strings.

iii) Continue joining subsequent thickness Pole sections until

the protected end of the Pole has reached the end of the Flag

sleeve at the top of the Flag.

iv) Tension the draw strings until the best result for the Banner is achieved. It is advisable to tie a reef knot as shown.

Assembling the Flag.

Kit overview - Your Flying Banner (feather or teardrop) flag kit comprises a 2, 3 or 4 piece pole in a Carry Bag & depending on what you have ordered, a Cross Base

(with or without Waterbag) &/or a Spike Base. The Carry Bag has enough compartments/space to store these components & your flag when not in use.

Flying Banner - Assembly & Installation Guide

Assembling the Cross Base.

i) Ensure the notched bar Cross Base is underneath.

ii) Screw the two bars together using the Spigot.

iii) Base shown assembled for indoor use. (The holes in the feet allow pegging into soft ground outdoors - pegs not included).

Using the Waterbag.

Fit the assembled Flag, either Feather or Teardrop style,onto either the Cross Base or Ground Spike.

Using the Ground Spike.

If fitting into very hard ground,use a steel hammer & a blockof wood to prevent damage to

the Spike.

i) Use a mallet or lump hammer to drive the Spike fully into the

ground taking care not to hit the rotating male Pole connector.

ii) Fit the Flag.

i) Fill the Waterbag.

ii) Tighten the cap. iii) Place onto the Cross Base.

iv) Fit the Flag.

Note: Feather Flag& Cross Base with

Waterbag is shown.

Note: Feather Flag& Cross Base with

Waterbag is shown.

Removing the Pole from the Flag.

i) Unhook/untie the draw strings. ii) Slide the Poles out.

iii) If the Poles separate, feed the Flag along

to remove them.

For use in soft ground,

sand or snow.

Optional for outdoor use.

FeatherFlag.

TeardropFlag.

Waterbag.

Cross Base.

Waterbag.

Cross Base.

TypicalAssembly

Ground level

WE DO NOT RECOMMEND USE OF OUR FLYING BANNERS IN WINDS IN EXCESS OF 25 M.P.H.

(For hard standingindoors or out).

DSU02-01

TEAR DROP FLAG