no a project office basis of estimate form (boe)

NOvA/ANU BoE Form of 2

NOνA Project Office BASIS of ESTIMATE FORM (BoE)

Document Number: 2087

Date of Estimate: May 28, 2007

Prepared by: Andrew Norman

UID Number:

WBS Section: 2.7.4.1.2.1

Task Name: Environmental and water cooling system sensor readout stations

Cost Type: Costing Method: ___Engineering Estimate

Prior purchase or experience Source:

_X__ Catalog Price Source: National Insturments

_ X_ M&S _ _Labor _X_Vendor Quote (attached) __ Other- Description:_____________________________ Attach Relevant Documents (including but not limited to): RFP, Responses to RFP, Technical Evaluation of RFP, Vendor Quotes, Technical Specifications, drawing numbers Task Duration: (calendar weeks, 85% achievable): see table below

Task M&S Cost (FY07$): $224,160 See cost table below Task M&S Contingency (%): 10% See cost table below

Task Labor (resource type & work hours or % for duration of task, 85% efficiency assumed): See cost table below Task Labor Contingency (%):See cost table below

Details of Estimate: Estimate is based upon 40 readout stations in the following base configuration: Configuration 1: Part Number Description Number Cost Total 778617-08 cFP-BP-8 8-Slot Backplane 1 549.00 549.00 779463-01 cFP-1808, 8-slot Ethernet/Serial Interface for Compact

FieldPoint 1 999.00 999.00

777584-01 PS-2 Power Supply, 24 VDC, 0.8 A, US (120 VAC) 1 79.00 79.00 777318-122 cFP-RTD-122, 16 Bit RTD Input Module (RTD, Ohms) 2 469.00 938.00 777318-550 cFP-DIO-550, Digital Input/Output Module (AC-DC sink/DC

source) 1 279.00 279.00

777318-500 cFP-CTR-500, Counter Input Module 1 429.00 429.00 777318-112 cFP-AI-112 16 ch, 16-Bit Analog Input Module (V) 4 599.00 2,396.00 Total: 5,669.00 Configuration 2: Part Number Description Number Cost Total 778617-08 cFP-BP-8 8-Slot Backplane 1 549.00 549.00 779463-01 cFP-1808, 8-slot Ethernet/Serial Interface for Compact

FieldPoint 1 999.00 999.00

777584-01 PS-2 Power Supply, 24 VDC, 0.8 A, US (120 VAC) 1 79.00 79.00 777318-122 cFP-RTD-122, 16 Bit RTD Input Module (RTD, Ohms) 2 469.00 938.00 777318-550 cFP-DIO-550, Digital Input/Output Module (AC-DC sink/DC

source) 1 279.00 279.00

777318-304 cFP-DI-304, 32-channel sinking Digital Input Module, 10-30 VDC

1 299.00 299.00

777318-112 cFP-AI-112 16 ch, 16-Bit Analog Input Module (V) 4 599.00 2,396.00 Total: 5,539.00

NOvA/ANU BoE Form of 2

See attached quotes and catalog pages for details of exact pricing for large orders.

My Shopping Cart (US Dollars) - National Instruments http://sine.ni.com/apps/utf8/nios.store

1 of 1 5/28/2007 1:01 AM

My Shopping Cart ( US Dollars )Questions? Call me now! or (866) 337-8762

Total Items: 11Subtotal: $ 5,669.00

Shipping in United States FedEx 2-DayFedEx 2-Day $ 50.88

Order Total: $ 5,719.88

Part Number Description Est Ship Unit Price Qty Line Total

779463-01 cFP-1808, 8-slot Ethernet/Serial Interface for Compact FieldPoint 5 - 10 $ 999.00 $ 999.00

778617-08 cFP-BP-8 8-Slot Backplane 5 - 10 $ 549.00 $ 549.00

777584-01 PS-2 Power Supply, 24 VDC, 0.8 A, US (120 VAC) 1 - 2 $ 79.00 $ 79.00

777318-112 cFP-AI-112 16 ch, 16-Bit Analog Input Module (V) 1 - 2 $ 599.00 $ 2,396.00

777318-550 cFP-DIO-550, Digital Input/Output Module (AC-DC sink/DC source) 1 - 2 $ 279.00 $ 279.00

777318-500 cFP-CTR-500, Counter Input Module 1 - 2 $ 429.00 $ 429.00

777318-122 cFP-RTD-122, 16 Bit RTD Input Module (RTD, Ohms) 1 - 2 $ 469.00 $ 938.00

Click the symbol to remove the item

Your Cart Options

Place Order Now

Print and Fax Order

Get Instant Quote

Save and Share Cart

Print Cart

Download to Excel

My Profile | Privacy | Legal | Contact NI © 2007 National Instruments Corporation. All rights reserved.

1

1

1

4

1

1

2

My Shopping Cart (US Dollars) - National Instruments http://sine.ni.com/apps/utf8/nios.store

1 of 1 5/28/2007 1:02 AM

My Shopping Cart ( US Dollars )Questions? Call me now! or (866) 337-8762

Total Items: 11Subtotal: $ 5,539.00

Shipping in United States FedEx 2-DayFedEx 2-Day $ 49.02

Order Total: $ 5,588.02

Part Number Description Est Ship Unit Price Qty Line Total

779463-01 cFP-1808, 8-slot Ethernet/Serial Interface for Compact FieldPoint 5 - 10 $ 999.00 $ 999.00

778617-08 cFP-BP-8 8-Slot Backplane 5 - 10 $ 549.00 $ 549.00

777584-01 PS-2 Power Supply, 24 VDC, 0.8 A, US (120 VAC) 1 - 2 $ 79.00 $ 79.00

777318-112 cFP-AI-112 16 ch, 16-Bit Analog Input Module (V) 1 - 2 $ 599.00 $ 2,396.00

777318-550 cFP-DIO-550, Digital Input/Output Module (AC-DC sink/DC source) 1 - 2 $ 279.00 $ 279.00

777318-122 cFP-RTD-122, 16 Bit RTD Input Module (RTD, Ohms) 1 - 2 $ 469.00 $ 938.00

777318-304 cFP-DI-304, 32-channel sinking Digital Input Module, 10-30 VDC 5 - 10 $ 299.00 $ 299.00

Click the symbol to remove the item

Your Cart Options

Place Order Now

Print and Fax Order

Get Instant Quote

Save and Share Cart

Print Cart

Download to Excel

My Profile | Privacy | Legal | Contact NI © 2007 National Instruments Corporation. All rights reserved.

1

1

1

4

1

2

1

522 National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • [email protected] • ni.com

Com

pact

Fie

ldPo

int B

ackp

lane

sIn

dust

rial

Con

trol

and

Dis

trib

uted

I/O

Overview National Instruments offers two backplanes for mounting Compact

FieldPoint modules – the cFP-BP-4 (4 slots) and the cFP-BP-8

(8 slots). Both backplanes, which are constructed of extruded metal

with grounding lugs on the bottom, feature screw-down connections

for a controller module, four or eight I/O modules, and 37 pin D-Sub

connectors for I/O connections. The backplanes all come with a

cFP-PM-H horizontal mounting bracket, which provides mounting

holes on either side of the backplane so you can mount it to a panel.

For other mounting options, you can purchase a vertical panel

mount, a DIN rail mount, or a 19 in. rack mount separately.

Compact FieldPoint and FieldPointThese backplanes are used with Compact FieldPoint only. Compact

FieldPoint is designed for industrial control applications that perform

advanced embedded control, data logging, headless operation, and

Ethernet connectivity. Compact FieldPoint is our most rugged and

reliable platform and is designed for industrial and mobile

environments with high shock, vibration, and temperature extremes.

FieldPoint is a lower-cost distributed I/O system with a variety of

communication options besides Ethernet. It is designed to mount on

DIN rails in static applications where the FieldPoint bank is connected

to a PC for data collection, analysis, display, and storage.

• 4 and 8-slot backplanes • Solid metal construction for rugged

installations • Panel, DIN rail, and 19 in. rack

mounting • Local bus for communications

and module power • Secure screw mounting for I/O

and control modules • -25 to 60 °C operating range

NI cFP-BP-4, NI cFP-BP-8

Compact FieldPoint BackplanesNEW

Back Plane I/O Module Slots Standard Mounting HardwarecFP-BP-4 4 cFP-PM-H horizontal panel mounting bracketcFP-BP-8 8 cFP-PM-H horizontal panel mounting bracket

Figure 1. Dimensions of the Compact FieldPoint systems with the cFP-BP-4 and cFP-BP-8 backplanes.

CablingClearance

Cooling Outline51 mm (2 in.)

All Around

4 slots = 246 mm (9.68 in.)8 slots = 441 mm (17.4 in.)

127

mm

(5.0

0 in

.)

Min

. 165

mm

(6

.50

in.)

CablingClearance

4 slots = 246 mm (9.68 in.)8 slots = 441 mm (17.4 in.)

Cooling Outline 51 mm (2 in.)

Cooling Outline 51 mm (2 in.)

Min

. 182

mm

(7.1

8 in

.)

106

mm

(4.1

8 in

.)

Compact FieldPoint BackplanesHigh Shock and VibrationTo withstand high levels of shock and vibration, Compact FieldPoint

backplanes are made of extruded metal and provide a rigid

mounting surface for the Compact FieldPoint modules. The

backplane also provides screw-down connections for the controller

module, I/O modules, and connector blocks.

Mounting NI offers four mounting options for Compact FieldPoint

backplanes including panel mounting, DIN-rail mounting, and

19 in. rack mounting.

Compact FieldPoint System ConfigurationCompact FieldPoint I/O modules mount on either the cFP-BP-4 or

cFP-BP-8 backplane. The backplane also contains a controller

module, which runs embedded LabVIEW Real-Time and can

connect over Ethernet to a PC, to other FieldPoint banks, to Web

browsers, or to other Ethernet devices. The Compact FieldPoint

backplane also provides a 37-pin D-Sub connector to connect your

field signal wiring for each I/O module. You have three options to

connect field wiring to this 37-pin D-Sub connector:

1. Using an integrated connector block such as the cFP-CB-1

or cFP-CB-11;

2. Using a cable to an external connector block mounted on a DIN rail;

3. Making your own custom cable.

For more details on configuring your Compact FieldPoint system,please see 517.

523National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • [email protected] • ni.com

Compact FieldPoint B

ackplanesIndustrial Control and D

istributed I/O

Number Needed to Number Needed toMounting Option Description Mount cFP-BP-4 Mount cFP-BP-8cFP-PM-H Panel mount with bolt holes at 1 1

the sides of the backplane.(included with all backplane)

cFP-PM-V Panel mount with bolt holes at the 1 1top and bottom of the backplane

cFP-RM-8 19 in. rack mount. Features captive 1 1screws for easy mounting and

cutouts for running grounding cablesDIN rail DIN rail clip for cFP-BP-4 1 2*mounting clip

* DIN rail mounting is not recommended for the cFP-BP-8NI cFP-BP-4 ..................................................................778617-04NI cFP-BP-8 ..................................................................778617-08

Recommended Compact FieldPoint System ProductsNI cFP-2020 ..............................................................777317-2020NI cFP-CB-1 ..................................................................778618-01NI PS-5 Power Supply ..................................................778805-90NI Developer Suite Professional Control Edition..........777906-03

BUY ONLINE!Visit ni.com/info and enter cfppb4, and/or cfppb8.

Ordering Information

Compact FieldPoint Accessories

Mounting Options (see figures 1, 2, and 3)NI offers four mounting options for Compact FieldPoint, including panel mounting, DIN rail mounting, and 19 in. rack mounting.

Power Supplies (see Figure 4)National Instruments offers five DC supplies for Compact FieldPoint systems. You connect the power supply output to the Compact FieldPoint

controller, which regulates, filters, and distributes power to the bank of up to eight I/O modules that it controls. All five power supplies can power an

entire bank of Compact FieldPoint I/O modules. The PS-5 mounts on a DIN rail and is recommended for most Compact FieldPoint installations.

Stand-Alone Controller-Mounting Accessories (see Figure 5)National Instruments offers options for mounting stand-alone Compact FieldPoint controllers. These accessories support applications for redundant

controllers without redundant I/O. The panel and DIN rail-mounting kits also provide mounting options for a stand-alone Compact FieldPoint real-time

controller running LabVIEW Real-Time software. Controller-mounting options include panel and DIN rail-mounting.

Figure 1. cFP-PM-V,Vertical-Mounting Kit

Figure 2. cFP-PM-H,Horizontal-Mounting Kit

Figure 3. cFP-RM-8,Rack-Mounting Kit

Figure 4. PS-5 PowerSupply (24 VDC)

Figure 5. Panel and DIN Rail-Mounting Kits

Mounting Option Description Quantity Needed to Mount cFP-BP-4 Quantity Needed to Mount cFP-BP-8 Part NumbercFP-PM-H Panel mount with bolt holes at the sides of

the backplane (included with all backplane)1 1 778616-01

cFP-PM-V Panel mount with bolt holes at the top and bottom of the backplane

1 1 778688-01

cFP-RM-8 19 in. rack mount; features captive screws for easymounting and cutouts for running grounding cables

1 1 778615-01

DIN Rail-Mounting Clip DIN rail clip for cFP-BP-4 1 21 778614-011DIN rail mounting is not recommended for the cFP-BP-8.

Model Output Voltage (VDC) Output Current (A) Input Voltage Part NumberPS-1 20 0.8 120 VDC 777567-01

PS-2 24 0.8 P = 1 U.S. 120/Japan 100 VAC2 Swiss 220 VAC, 3 Australian4 Universal Euro 240 VAC5 North American 240 VAC6 United Kingdom 240 VAC

777584-0P

PS-3 13.8 4 Same as PS-2 777585-0P

PS-4 24 0.625 90 to 260 VAC 50/60 Hz 778586-90PS-5 24 5 90 to 260 VAC 50/60 Hz 778805-90

Power connects to the cFP-21xx modules, which regulate, filter, and distribute to attached I/O modules.

Model Description Part NumberPanel Panel-mounting kit for stand-alone controllers 779549-01

DIN rail DIN rail-mounting kit for stand-alone controllers 779552-01

BUY NOW!For complete product specifications, pricing, and accessory information, call (800) 813 3693 (U.S.) or go to ni.com/compactfieldpoint.

NI Services and Support

NI has the services and support to meet

your needs around the globe and through

the application life cycle – from planning

and development through deployment

and ongoing maintenance. We offer

services and service levels to meet

customer requirements in research,

design, validation, and manufacturing.

Visit ni.com/services.

Training and CertificationNI training is the fastest, most certain route to productivity with our

products. NI training can shorten your learning curve, save development

time, and reduce maintenance costs over the application life cycle. We

schedule instructor-led courses in cities worldwide, or we can hold a

course at your facility. We also offer a professional certification program

that identifies individuals who have high levels of skill and knowledge on

using NI products. Visit ni.com/training.

Professional ServicesOur Professional Services Team is comprised of NI applications engineers,

NI Consulting Services, and a worldwide National Instruments Alliance

Partner program of more than 600 independent consultants and

integrators. Services range from

start-up assistance to turnkey

system integration.

Visit ni.com/alliance.

OEM SupportWe offer design-in consulting and product integration assistance if you

want to use our products for OEM applications. For information about

special pricing and services for OEM customers, visit ni.com/oem.

Local Sales and Technical SupportIn offices worldwide, our staff is local to the country, giving you access

to engineers who speak your language. NI delivers industry-leading

technical support through online knowledge bases, our applications

engineers, and access to 14,000 measurement and automation

professionals within NI Developer Exchange forums. Find immediate

answers to your questions at ni.com/support.We also offer service programs that provide automatic upgrades to

your application development environment and higher levels of technical

support. Visit ni.com/ssp.

Hardware Services

NI Factory Installation ServicesNI Factory Installation Services (FIS) is the fastest and easiest way to

use your PXI or PXI/SCXI combination systems right out of the box.

Trained NI technicians install the software and hardware and configure

the system to your specifications. NI extends the standard warranty by

one year on hardware components (controllers, chassis, modules)

purchased with FIS. To use FIS, simply configure your system online with

ni.com/pxiadvisor.

Calibration Services NI recognizes the need to maintain properly calibrated devices for

high-accuracy measurements. We provide manual calibration

procedures, services to recalibrate your products, and automated

calibration software specifically designed for use by metrology

laboratories. Visit ni.com/calibration.

Repair and Extended Warranty NI provides complete repair services for our products. Express repair

and advance replacement services are also available. We offer

extended warranties to help you meet project life-cycle requirements.


SERVICE NEEDS

© 2006 National Instruments Corporation. All rights reserved. FieldPoint, LabVIEW, National Instruments, National Instruments Alliance Partner, NI, ni.com, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies.A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI.

National Instruments • [email protected]

ni.com • (800) 813 3693 *351355A-01*351355A-01 2006-6643-161-101-D

Overview and Distributed ApplicationsNational Instruments cFP-180x interfaces connect four or eight

Compact FieldPoint I/O modules to a high-speed Ethernet network or to

an RS232 serial port. With up to 100 Mb/s data communication rates and

event-driven communications, an NI cFP-180x delivers a high-performance

network connection for Compact FieldPoint that is easy to interface with

a PC or PAC-like Compact FieldPoint embedded controller. One or more

cFP-180x interfaces, connected by standard networking equipment, provide

expanded I/O that you can control with a single Compact FieldPoint

controller, see Figure 1. You can also build a PC-based distributed I/O and

control system by connecting two or more cFP-180x devices to your PC.

Hardware ArchitectureA cFP-180x provides an integrated network interface (Ethernet or serial)

and a 4 or 8-slot backplane, and it works with the same modules and

connector blocks used in other Compact FieldPoint systems.

Building Ethernet-Based Distributed I/O SystemsA cFP-180x can communicate with Compact FieldPoint real-time

embedded controllers; any Ethernet-based programmable automation

controller (PAC); and a Windows computer running LabVIEW,

LabWindows/CVI, Measurement Studio, Lookout, or your choice of OPC

client application software. Using a cFP-180x, you can rapidly build

flexible, modular distributed measurement and automation systems.

Ethernet/Serial Interfaces for Compact FieldPoint

• Distributed I/O interfaces for Ethernetand RS232 networks

• 4 or 8-slot Compact FieldPoint distributedEthernet/serial network interfaces

• FieldPoint software for rapid distributedI/O access

• Modbus Support• OPC server included• Intelligent diagnostics and maintenance • Industrial specifications for

harsh environments• 50 g shock• 5 g vibration• -40 to 70 °C

Operating Systems• Windows 2000/XP

Recommended Software• LabVIEW• LabVIEW Datalogging and Supervisory

Control Module

Other Compatible Software• LabWindows/CVI• Measurement Studio• Lookout• VI Logger

Driver Software (included)• Measurement & Automation Explorer• OPC server (2.0 compliant)

NI cFP-180x

Compact FieldPoint

Real-Time Controller

NI cFP-1808 Distributed

Network Interfaces

Ethernet

Figure 1. Expansion I/O for Compact FieldPoint Embedded Controller with cFP-1808Network Interfaces

Figure 2. cFP-1808 Mechanical Dimensions

127 mm(5.00 in.)

441 mm(17.36 in.)

Figure 3. cFP-1804 Mechanical Dimensions

127.0 mm(5.00 in.)

245.9 mm (9.68 in.)


2

BUY ONLINE at ni.com or CALL (800) 813 3693 (U.S.)

Network Communications InterfaceA cFP-180x connects directly to Ethernet networks, autonegotiating on

the network for 10 Mb/s or 100 Mb/s communication rates. It includes

an RJ-45 connector for connection to 10BaseT and 100BaseTX networks,

using a protocol based on standard TCP/IP to maintain full compatibility

with existing networks. FieldPoint builds on standard TCP/IP network

protocols and adds a number of key enhancements, including event-

driven communications and publisher-subscriber networking. In a

publisher-subscriber architecture, one or more client PCs subscribe to

I/O data from Compact FieldPoint banks. The network interface monitors

connected I/O modules and publishes I/O data only when the value

changes. Analog signals can change value within selectable ranges,

called deadbands, without causing the system to report data. This

event-driven method, along with data compression, helps you avoid

unnecessary Ethernet traffic and maximizes communication efficiency.

A cFP-180x also includes a standard DB-9 connector for RS232 serial

communication. Through direct connectivity, you can read and write

data directly from a program running on your PC or embedded controller.

You access I/O through the serial interface using a serial protocol called

Optomux, in the same way you would access data through classic

FieldPoint network interfaces such as the FP-1000.

Configuring and Accessing Tags on aCompact FieldPoint System with LabVIEW 8National Instruments LabVIEW 8 and Compact FieldPoint create a

flexible PAC system that offers easy-to-access I/O through the FieldPoint

programming environment. Accessing data from multiple cFP-180x

distributed nodes with LabVIEW is as easy as three simple steps:

1. Configure IP address using NI Measurement & Automation Explorer (MAX)

2. Import a FieldPoint configuration file or add a new

Compact FieldPoint system

3. Expand I/O in the LabVIEW Project and drag and drop I/O tags to VIs

After configuring the IP address for a FieldPoint bank in MAX, either

import the configuration file created from MAX, or simply add a new

target to a LabVIEW Project as shown in Figure 5.

After adding all FieldPoint networks available on the network, you can

expand each FieldPoint bank and see the I/O modules and tags available

from the LabVIEW Project Explorer. Using these tags in an application is

as easy as dragging the tag from the Project Explorer to the VI where the

data is needed. LabVIEW automatically creates the correct FieldPoint

read/write VI and associated tag.

Figure 5. Add a new FieldPoint target to your LabVIEW 8 Project.

HMIs and

Touch Panels

Programmable

Automation

Controllers

Compact FieldPoint

Real-Time Controller

Distributed Compact FieldPoint

Network Interface

Figure 4. Ethernet-based distributed systems work with Compact FieldPoint embedded controllers, PACs, human-machine interfaces, and Enterprise/SCADA systems.

Enterprise Level


3


Accessing Network I/O Data on a cFP-180x Using Shared VariablesYou can create a shared variable for any tag that is available on a

cFP-180x bank connected to the network. You then can use this shared

variable in multiple LabVIEW applications either targeted to Windows OS

or running embedded on a Compact FieldPoint real-time controller such as

the NI cFP-2120. To create a shared variable to be hosted on a Windows

system, simply right-click on My Computer in the LabVIEW Project and

select New Variable; select the option to bind this shared variable to a

source, and then you can either select IO from your local LabVIEW Project

or any I/O available on the network, as shown in Figure 7.

After you create a shared variable, it appears in LabVIEW Project

Manager and is available for use in your LabVIEW applications simply

by dragging the variable from the Project Explorer to an existing VI

(see Figure 8). From a PC, PAC, or embedded Compact FieldPoint controller,

you can use MAX with LabVIEW 8 to configure I/O settings for the

cFP-180x to access data on distributed Compact FieldPoint banks.

Accessing distributed I/O is now easier than ever with LabVIEW 8

and a cFP-180x.


NI cFP-1808 ...........................................................................779463-01

NI cFP-1804 ...........................................................................779490-01

PS-5 (power supply 24 VDC, 5 A, universal power input) ......778805-90

BUY NOW!For complete product specifications, pricing, and accessoryinformation, call (800) 813 3693 (U.S.) or go to ni.com/fieldpoint.

Figure 6. Drag and drop an I/O tag from a LabVIEW Project to any VI.

Figure 7. Compact FieldPoint distributed I/O channels are accessible as network itemsfrom LabVIEW.

Figure 8. Use a shared variable to access distributed I/O for all channels.


4


SpecificationsNetworkNetwork interface............................... 10BaseT and 100BaseTX EthernetCompatibility ....................................... IEEE802.3Communication rates .......................... 10 or 100 Mb/s, autonegotiatedMaximum cabling distance................. 100 m/segmentMaximum power to I/O modules........ 9 WMaximum number of banks ................ Determined by network topology

Serial PortOne RS232 (DCE) serial port

Baud rate ........................................ 300 to 115,200 b/sData bits ......................................... 8Stop bits.......................................... 1Parity ............................................... NoneFlow control .................................... None

Power RequirementPower supply range ............................ 11 to 30 VDCRecommended power supply.............. 20 WPower consumption ............................ 6.1 W + 1.1 (I/O module)

Safety Isolation VoltageIsolation voltage is verified by a dielectric withstand test betweenmodule and backplane.Continuous .......................................... 250 Vrms,

Measurement Category IIWithstand............................................ 2,300 Vrms, 5 s max

Physical CharacteristicsScrew-terminal wiring ........................ 14 to 22 AWG copper wire with

7 mm (0.28 in.) of insulationstripped from the end

Torque for screw terminals................. 0.5 to 0.6 N • m(4.4 to 5.3 lb • in.)

WeightcFP-1804 ......................................... 935 g (2 lb 1 oz)cFP-1808 ......................................... 1,595 g (3 lb 8 oz)

EnvironmentalFieldPoint modules are intended for indoor use only. For outdoor use,they must be installed in a suitable sealed enclosure.

Operating temperature ....................... -40 to 70 °CStorage temperature........................... -55 to 85 °CRelative humidity ................................ 10 to 90%, noncondensingMaximum altitude............................... 2,000 m; at higher altitudes

the isolation voltage ratingsmust be lowered

Pollution Degree ................................. 2

Shock and VibrationOperating vibration

Random (IEC 60068-2-64) ............... 10 to 500 Hz, 5 grmsSinusoidal (IEC 60068-2-6) ............. 10 to 500 Hz, 5 g

Operating shock(IEC 60068-2-27) ............................. 50 g, 3 ms half sine, 18 shocks at

6 orientations; 30 g, 11 ms halfsine, 18 shocks at 6 orientations

SafetyThis product is designed to meet the requirements of the followingstandards of safety for electrical equipment for measurement, control,and laboratory use:

• IEC 61010-1, EN 61010-1• UL 61010-1• CAN/CSA-C22.2 No. 61010-1

Note: For UL, hazardous location, and other safety certifications, refer to the product label orvisit ni.com/certification, search by model number or product line, and click the appropriatelink in the Certification column.

Electromagnetic CompatibilityEmissions ............................................ EN 55011 Class A at 10 m

FCC Part 15A above 1 GHzImmunity.............................................. EN 61326:1997 + A2:2002, Table 1

CE, C-Tick, and FCC Part 15(Class A) Compliant

Note: For EMC compliance, operate this device with shielded cabling.

CE ComplianceThis product meets the essential requirements of applicable Europeandirectives, as amended for CE marking, as follows:

Low-voltage directive (safety) ............ 73/23/EECElectromagnetic compatibilitydirective (EMC).................................... 89/336/EECNote: Refer to the Declaration of Conformity (DoC) for this product for any additional regulatorycompliance information. To obtain the DoC for this product, visit ni.com/certification, searchby model number or product line, and click the appropriate link in the Certification column.























system integration.













Hardware Services







ni.com/pxiadvisor.










SERVICE NEEDS

© 2006 National Instruments Corporation. All rights reserved. CVI, FieldPoint, LabVIEW, Lookout, Measurement Studio, National Instruments, National Instruments Alliance Partner, NI, ni.com, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies. A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI.


ni.com • (800) 813 3693 *342572A-01*342572A-01 2006-6507-161-101-D

Thermocouple and RTD Modules for Compact FieldPoint

OverviewThe National Instruments cFP-TC-12x and cFP-RTD-12x are versatile

temperature input modules for Compact FieldPoint, used to measure

thermocouples, millivolt-level voltages, thermistors, and 2, 3, and 4-wire

RTDs. They are used in applications such as temperature chamber control,

device testing, and process control. Thermocouples are low-cost, flexible

temperature devices. RTD sensors are used in applications for acquiring

temperatures with high accuracy. Two and 3-wire RTDs work well for

applications with short signal wires and low noise levels; 4-wire RTDs are

well-suited for applications with long signal wires or high noise levels.

All of these I/O modules include overranging and onboard diagnostics to

ensure trouble-free installation and maintenance. The modules measure

and linearize signals on board to return scaled values to your control or

monitoring software. NI cFP-TC-12x and cFP-RTD-12x modules have NIST-

traceable calibration certificates (available on request), ensuring accurate

and reliable analog measurements.

Compact FieldPointCompact FieldPoint is designed for industrial control applications that

perform advanced embedded control, data logging, headless operation,

and Ethernet connectivity. Compact FieldPoint, a rugged, reliable NI platform,

is designed for industrial and mobile environments with high shock,

vibration, and temperature extremes.

IsolationThe cFP-TC-125 provides 250 Vrms common-mode voltage protection

between channels, and all cFP-TC-12x and cFP-RTD-12x modules

feature optical bank isolation with 2,300 Vrms of breakdown isolation.

In addition, the cFP-TC-12x and cFP-RTD-12x provide double insulation

for up to 250 Vrms of operational isolation. You can safely use Compact

FieldPoint with the cFP-CB-1 or cFP-CB-3 connector block in applications

where hazardous voltages are present.

• 8 temperature inputs• Thermocouple or millivolt• 2, 3, or 4-wire RTD

• Built-in signal conditioningbetween channels• 250 V common-mode isolation

on TC-125• 50 and 60 Hz noise rejection

• 16-bit resolution• Input ranges configurable in software

for each channel• 2,300 Vrms bank isolation for transient

overvoltage protection• Hot-swappable with autoconfiguration• -40 to 70 °C operating range

NI cFP-TC-120, NI cFP-TC-125, NI cFP-RTD-122, NI cFP-RTD-124

ModuleInput

ChannelsResolution

(bits) Input TypeInput Ranges Software

Configurable per Channel50/60 Hz

Noise FilterAll-Channel

Update PeriodCommon-Mode

Between ChannelsSafety

IsolationcFP-TC-120 8 16 Thermocouple J,K,R,S,T,N,E, and B ± 25 mV, ±50 mV, 3 1.13 s (0.88 Hz) – 2,300 Vrms

bank isolation Millivolt ±100 mV, -20 to 80 mVcFP-TC-125 8 16 Thermocouple J,K,R,S,T,N,E, and B 3 0.22 s (Filter Off)

0.99 s (Filter On)250 Vrms 2,300 Vrms

bank isolation Millivolt -20 to 80 mVcFP-RTD-122 8 16 2, 3-Wire RTD Pt 100, Pt 1,000 3 1.08 s (0.93 Hz) – 2,300 Vrms

bank isolation Resistance 0 to 400, 0 to 4000 ΩcFP-RTD-124 8 16 2, 4-Wire RTD Pt 100 3 1.08 s (0.93 Hz) – 2,300 Vrms

bank isolation Resistance 0 to 400 Ω

Smart I/O ModulesThe cFP-TC-12x and cFP-RTD-12x modules offer 16-bit resolution for

high-accuracy measurements, and you can connect directly to industrial

sensors or units under test with the safety isolation available. The modules

filter, calibrate, and scale raw sensor signals to engineering units, as

well as perform self-diagnostics to look for problems such as open

thermocouples. With cFP-TC-12x and cFP-RTD-12x modules, your software

application reads a linearized, calibrated, scaled value from the I/O module,

eliminating the error-prone step of converting binary values to temperature.

For increased accuracy and noise rejection, the modules use a

16-bit delta-sigma ADC with an integrated lowpass filter on each

channel, which is configured for 50 and 60 Hz rejection. With high-accuracy

16-bit delta-sigma ADCs on the I/O modules, you also get instrument-quality

measurements on an industrially rugged, distributed, embedded system.

cFP-TC-12x and cFP-RTD-12x modules offer a variety of different update

rates to fit your application, ranging from 0.22 s with filters off and 1.08

to 1.13 s with filters enabled. Overall data throughput depends on filter

settings across all channels, software loop speeds, and network speeds.

cFP-TC-120The cFP-TC-120 includes eight differential inputs for thermocouples.

It also provides cold-junction compensation using a thermistor embedded

in the connector block. An onboard microcontroller compensates and

linearizes the thermocouple reading to the NIST IST-90 standard,

using an advanced linearization routine for maximum accuracy.

cFP-TC-125In addition to the thermistor and linearization features of the cFP-TC-120,

the cFP-TC-125 provides 250 Vrms of common-mode rejection, ideal for

applications where differences in voltages might exist between connected

thermocouples. The cFP-TC-125 also provides 0.22 s update rates when

the 50/60 Hz filter is not enabled.

cFP-RTD-122The cFP-RTD-122 includes eight inputs for 2 and 3-wire RTDs.

The module uses a stable current source for sensor excitation and an

onboard microcontroller that linearizes and scales the measurements to

temperature units. You can configure each channel of the module to

return data scaled to temperature (°C, °F, or °K) or resistance. The 3-wire

configuration used with the cFP-RTD-122 eliminates errors caused by

lead wire resistance but does not reduce errors caused by noise. If your

application involves high noise or long wires, you should use 4-wire RTDs

with the cFP-RTD-124.

cFP-RTD-124The cFP-RTD-124 includes eight inputs for 2 and 4-wire RTDs. The module

uses a stable current source for sensor excitation and an onboard

microcontroller that linearizes and scales the measurements to temperature

units. You can configure each channel of the modules to return data scaled

to temperature (°C, °F, or °K) or resistance. Four-wire RTDs used with the

cFP-RTD-124 are ideal for applications involving long signal wires or high

signal noise. The 4-wire configuration eliminates the voltage drop caused

by lead wire resistance and reduces errors caused by noise.

Isothermal Connectivity for the cFP-TC-12xFor maximum accuracy, NI recommends using an isothermal connector

block with the cFP-TC-12x. The cFP-CB-3 isothermal connector block

minimizes the temperature gradient across wiring connections,

improving the accuracy of the cold-junction measurement, and,

therefore, of thermocouple measurements.

Compact FieldPoint I/O ConnectionsCompact FieldPoint modules include a built-in power distribution bus

that provides multiple power connections on the module. A field-wired

power supply connected to the voltage (V) and common (C) terminals is

internally connected to a power distribution bus that provides additional

breakout terminals for voltage supply (VSUP) and common (COM). These

terminals offer a convenient way to distribute power to field devices that

require external power.

Each cFP-TC-12x input channel has two terminals for differential input:

1. Thermocouple positive input (IN+)

2. Thermocouple negative input (IN-)

Each cFP-RTD-122 input channel has three terminals:

1. Excitation output (EXCITE)

2. Sensing input (SENSE)

3. Common input (COM)

Each cFP-RTD-124 input channel has four terminals:

1. Excitation output (EXCITE)

2. Positive sensing input (SENSE+)

3. Negative sensing input (SENSE-)

4. Common input (COM)


2


Figure 1. Wiring Diagram for cFP-RTD-12x

Figure 2. Wiring Diagram for cFP-TC-120

Figure 3. Wiring Diagram for cFP-TC-125Note: Connections will depend on the application.


3



NI cFP-TC-120 ......................................................................777318-120

NI cFP-TC-125 ......................................................................777318-125

NI cFP-RTD-122 ..................................................................777318-122

NI cFP-RTD-124 ..................................................................777318-124

Recommended System ProductsNI cFP-2120 ......................................................................777317-2120

NI cFP-1804 ..........................................................................779490-01

NI cFP-BP-4 ............................................................................778617-04

NI cFP-CB-1............................................................................778618-01

NI cFP-CB-3............................................................................778618-03

NI PS-5 Power Supply ..........................................................778805-90

BUY NOW!For complete product specifications, pricing, and accessory information, call (800) 813 3693 (U.S.) or go to ni.com/advisors.

EX+ (Ch 0)

[c]FP-RTD-122

SENSE (Ch 0)

COM (Ch 0)

2-Wire RTD

ShortJumper

Wire

EX+ (Ch 1)

SENSE (Ch 1)

COM (Ch 1)

3-Wire RTD

EX+ (Ch 7)

SENSE (Ch 7)

COM (Ch 7)

4-Wire RTD

Leave this wire unconnected

SENSE+ (Ch 0)

[c]FP-RTD-124

SENSE– (Ch 0)

COM (Ch 0)

EXCITE+ (Ch 0)

2-Wire RTD

ShortJumper

Wire

ShortJumperWires

SENSE+ (Ch 1)

SENSE– (Ch 1)

COM (Ch 1)

EXCITE+ (Ch 1)

3-Wire RTD

SENSE+ (Ch 7)

SENSE– (Ch 7)

COM (Ch 7)

EXCITE+ (Ch 7)

4-Wire RTD

Thermocouple

[c]FP-TC-120

IN(–)

IN(+)

Shield

CV

To Next Channel

Thermocouple

cFP-TC-125

IN(–)

IN(+)

Shield

SpecificationsTypical for -40 to 70 °C unless otherwise noted.

Input CharacteristicsNumber of inputs ................................ 8ADC resolution .................................... 16 bits, 1 in 65,536Type of ADC ........................................ Delta-sigmaFilters................................................... 50/60 Hz rejectionExcitation current

cFP-RTD-122 ................................... 0.25 mAcFP-RTD-124 ................................... 2 mA

Data scaling optionscFP-TC-120...................................... Temperature (°C, °F, °K) or mVcFP-RTD-12x.................................... Temperature (°C, °F, °K)

or resistance (Ω)Update period, all channels

cFP-TC-125Filter off ...................................... 0.22 sFilter on ...................................... 0.99 s

cFP-TC-120...................................... 1.13 scFP-RTD-12x.................................... 1.08 s

Signal input bandwidthcFP-TC-120...................................... 3 HzcFP-TC-125...................................... 12 Hz

Cold-junction accuracy cFP-TC-12xWith cFP-CB-3 connector block...... 0.25 °C typ, 0.5 °C max

Input impedance (cFP-TC-12x) ............ 20 MΩInput current (cFP-TC-12x)................... 35 nA typ, 140 nA maxInput noise .......................................... ±1 LSBpp

Overvoltage protectioncFP-TC-120...................................... ±40 VcFP-TC-125...................................... ±250 V

Common-mode voltage between channels referencedto isolated ground

cFP-TC-125...................................... 250 VcFP-TC-120...................................... 1 VcFP-RTD-12x.................................... 2 V

Safety Isolation VoltageMaximum safety isolation voltage ..... 250 Vrms, Installation Category II

(cFP-TC-12x only)Channel-to-channel safety isolation... No isolation between channelsTransient overvoltage.......................... 2,300 Vrms

Physical CharacteristicsLED indicators

POWER (green) ............................... Power on and self-test passedREADY (green) ................................ Module configured and readyOPEN TC <0..7> (red)

(cFP-TC-12x)................................ Open or broken thermocoupleon channel

Dimensions.......................................... 128 by 88 by 25 mm(5.0 by 3.5 by 1.0 in.)

WeightcFP-TC-120...................................... 130 g (4.6 oz)cFP-TC-125...................................... 125 g (4.4 oz)cFP-RTD-12x.................................... 110 g (3.7 oz)

Power RequirementPower from network module

cFP-TC-120...................................... 350 mWcFP-TC-125...................................... 650 mW

EnvironmentalOperating temperature ....................... -40 to 70 °CStorage temperature........................... -55 to 85 °C

(cFP-TC-125 -40 to 80 °C)Relative humidity ................................ 10 to 90%, noncondensingMaximum altitude............................... 2,000 m; at higher altitudes

the isolation voltage ratingsmust be lowered

Pollution degree .................................. 2

Shock and VibrationOperating vibration, random

(IEC 60068-2-64) ............................. 10 to 500 Hz, 5 grms

Operating vibration, sinusoidal(IEC 60068-2-6) ............................... 10 to 500 Hz, 5 g

Operating shock(IEC 60068-2-27) ............................. 50 g, 3 ms half sine,

18 shocks at 6 orientations;30 g, 11 ms half sine,18 shocks at 6 orientations

Safety and Compliance

SafetyThis product is designed to meet the requirements of the followingstandards of safety for electrical equipment for measurement, control,and laboratory use:

• IEC 61010-1, EN 61010-1• UL 3121-1, UL 61010C-1• CAN/CSA C22.2 No. 1010.1

For UL, hazardous location, and other safety certifications, refer to theproduct label or to ni.com

Electromagnetic CompatibilityCE, C-Tick, and FCC Part 15 (Class A)Compliant Emissions........................... EN 55011 Class A at 10 m FCC

Part 15A above 1 GHz ImmunityEN 61326:1997 +A2:2001, Table 1

Note: For EMC compliance, you must operate this device withshielded cabling.


4


CE ComplianceThis product meets the essential requirements of applicable EuropeanDirectives, as amended for CE Marking, as follows:

Low-Voltage Directive (safety) ........... 73/23/EECElectromagnetic Compatibility

Directive (EMC)............................... 89/336/EEC

Refer to the Declaration of Conformity (DoC) for this product for any additionalregulatory compliance information. To obtain the DoC for this product,visit ni.com/certification and search by model number or product line.


5



















Professional ServicesOur Professional Services Team is composed of NI applications engineers,





system integration.













Hardware Services






purchased with FIS. To use FIS, simply configure your system online

with ni.com/pxiadvisor.










SERVICE NEEDS

© 2006 National Instruments Corporation. All rights reserved. FieldPoint, National Instruments, National Instruments Alliance Partner, NI, ni.com, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies.A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI.


ni.com • (800) 813 3693 *351395A-01*351395A-01 2006-7533-161-101-D

Digital Input Modules for Compact FieldPoint and FieldPoint

OverviewThe National Instruments [c]FP-DI-3xx devices are versatile digital input

modules. The DI-300, DI-301, and DI-330 are available in the Compact

FieldPoint and FieldPoint product families. The new NI cFP-DI-304 module

is available for Compact FieldPoint systems. You can use these modules

to monitor digital signals ranging from low voltage levels up to 250 V.

They are commonly used to monitor proximity and limit switches,

pushbutton switches, thermostat outputs, relay closures, power circuits,

and TTL devices. All the modules include onboard diagnostics to ensure

trouble-free installation and maintenance.

Digital Input ModulesThe [c]FP-DI-3xx modules provide built-in module-to-module isolation to

protect your FieldPoint system and controller or communication interface

from high voltage levels. The DI-300, DI-301, and DI-304 modules use a

common ground plane for all the input channels. Each channel on the DI-300,

DI-301, and DI-304 modules include current-limiting circuitry to prevent

module damage when connected directly to a 24 VDC source. The DI-330

uses eight optically isolated input channels so that each digital input has

a separate ground plane, and you can use each channel with a different

voltage potential. Thus, you can connect one channel to a 5 VDC TTL signal

and another signal on the same DI-330 module to a 250 VAC line voltage.

Each channel on the DI-330 includes current-limiting circuitry that limits the

total current to 1.5 mA to prevent damaging the module. All channels on

the DI-3xx modules feature LEDs that indicate the input state of each

channel. The modules feature an all channel update rate of 1 kHz. Overall

data throughput depends on software loop speeds and network speeds.

IsolationThe [c]FP-DI-3xx modules feature bank isolation with 2,300 Vrms of

breakdown isolation. In addition, the DI-330 provides double insulation

for up to 250 Vrms of operational isolation. You can safely use Compact

FieldPoint in applications where hazardous voltages are present when

used with the cFP-CB-1 connector block. You can safely use FieldPoint in

applications where hazardous voltages are present with the FP-TB-x

terminal base. These Compact FieldPoint and FieldPoint modules do not

have channel-to-channel isolation.

Field I/O ConnectionsCompact FieldPoint and FieldPoint modules include a built-in power

distribution bus that provides multiple power connections on the module.

A field wired power supply connected to the voltage (V) and common (C)

terminals is internally connected to a power distribution bus that delivers

additional breakout terminals for voltage supply (VSUP) and common

(COM). These terminals offer a convenient way to distribute power

to field devices that require external power.

• 8,16, or 32 channel inputs• 24 VDC inputs• 4 to 250 VDC inputs• 15 to 250 VAC inputs (50/60 Hz AC)• 3 to 250 VAC inputs (1 kHz AC)

• 2,300 Vrms bank isolation for transientovervoltage protection

• Hot-swappable with autoconfiguration• -40 to 70 °C operating range

FieldPoint Software (included)• FieldPoint 5.0 (for all models)

NI [c]FP-DI-300, NI [c]FP-DI-301,NI cFP-DI-304, NI [c]FP-DI-330 NEW!

Module Input Channels Input Ranges Input Type Compatibility ExamplesSeparate Ground

Plane per ChannelAll ChannelUpdate Rate

AdditionalFeatures

[c]FP-DI-300 8 18 to 30 VDC Sinking 24 VDC sourcing devices – 1 kHz –

[c]FP-DI-301 16 18 to 30 VDC Sinking 24 VDC sourcing devices – 1 kHz –

cFP-DI-304 32 10 to 30 VDC Sinking 24 VDC sourcing devices – 1 kHz Hysteresis

[c]FP-DI-330 8 5 to 48 VDC5 to 250 VAC

Sinking or sourcing TTL, CMOS, 12 VDC, 24 VDC,48 VDC, 120/240 VAC/VDC

3 1 kHz Input current limiting(1.5 mA)


2


To next channel

[c]FP-DI-330

VSUP (Ch 0)

COM (Ch 0)

V C

+

–Input

Circuitry INB (Ch 0)

INA (Ch 0)Sinking-Output

Device with External

Power

VSUP (Ch 1)

COM (Ch 1)

INB (Ch 1)

INA (Ch 1)

VSUP (Ch 2)

COM (Ch 2)

INB (Ch 2)

INA (Ch 2)

InputCircuitry

InputCircuitry

+

–

Sourcing-Output


Power

Sinking-OutputDevice

Powered by [c]FP-DI-330

VSUP (Ch 3)

COM (Ch 3)

INB (Ch 3)

INA (Ch 3)

InputCircuitry

Sourcing-OutputDevice

Powered by [c]FP-DI-330

VSUP (Ch n)

COM (Ch n)

INB (Ch n)

INA (Ch n)

InputCircuitry

+ –5-250 V ExternalPower Supply

SwitchTo next channel

[c]FP-DI-300/301/304

VIN (Ch 0)

VSUP (Ch 0)

COM (Ch 0)

V C

InputCircuitry

SourcingOutput


Power

+

–

VIN (Ch 1)

VSUP (Ch 1)

COM (Ch 1)

InputCircuitry

SourcingOutputDevice

Powered by[c]FP-DI-30x

VIN (Ch n)

VSUP (Ch n)

COM (Ch n)

InputCircuitry

–

+15-30 VDC

External Power Supply

Switch

Wiring Schematics for the [c]FP-DI-3xx Modules


Compact FieldPoint

NI cFP-DI-300 ......................................................................777318-300

NI cFP-DI-301 ......................................................................777318-301

NI cFP-DI-304 ......................................................................777318-304

NI cFP-DI-330 ......................................................................777318-330

Recommended Compact FieldPoint System Products

NI cFP-2120 ......................................................................777317-2120

NI cFP-BP-4 ............................................................................778617-04

NI cFP-BP-8 ............................................................................778617-08

NI cFP-CB-1............................................................................779618-01


NI Developer Suite Professional Control Edition..................777906-03

FieldPoint

NI FP-DI-300 ........................................................................777518-300

NI FP-DI-301 ........................................................................777518-301

NI FP-DI-330 ........................................................................777518-330

Recommended FieldPoint System Products

NI FP-1601 ............................................................................777792-01

NI FP-TB-1..............................................................................777519-01


NI Developer Suite Control Edition ......................................777905-03

BUY NOW!For complete product specifications, pricing, and accessory information, call (800) 813 3693 (U.S.) or go to ni.com.


3


SpecificationsTypical for -40 to 70 °C unless otherwise noted.

Digital Input Channels[c]FP-DI-300, [c]FP-DI-330 ...................................................... 8[c]FP-DI-301............................................................................ 16cFP-DI-304.............................................................................. 32

Input CharacteristicsInput impedance

[c]FP-DI-300, [c]FP-DI-301 .................................................. 5 kΩcFP-DI-304.......................................................................... 30 kΩ

Input current limiting [c]FP-DI-330......................................... 1.5 mA

Input Voltages[c]FP-DI-300, [c]FP-DI-301, cFP-DI-304................................... 0 to 30 VDC[c]FP-DI-330............................................................................ 0 to 250 VDC or 0 to 250 VAC (50/60 Hz AC) or 0 to 250 VAC (1 KHz AC)

Digital Logic Levels

Hysteresis (cFP-DI-304)Input voltage .......................................................................... 2 V minInput current........................................................................... 60 µA min

Isolation Voltage[c]FP-DI-30x

Channel-to-ground Continuous .................................................................... 250 Vrms

Withstand...................................................................... 2,300 Vrms, 5 s maxChannel-to-backplane

Continuous .................................................................... 250 Vrms

Withstand...................................................................... 2,300 Vrms, 5 s maxChannel-to-channel ........................................................... None

[c]FP-DI-330Maximum isolation voltage............................................... 250 Vrms, Installation Category II

Transient overvoltage ............................................................ 2,300 Vrms


Power (green) .................................................................... Power on and self-test passedReady (green)..................................................................... Module configured and ready<0..31>, <0..15>, or <0..7> (green) ....................................... Input state of each channel

Dimensions Compact FieldPoint............................................................ 2.4 by 12.7 by 6.6 cm (0.94 by 5 by 2.6 in.)FieldPoint (including terminal base).................................. 10.7 by 10.9 by 9.1 cm (4.2 by 4.3 by 3.6 in.)

WeightFP-DI-300/301.................................................................... 130 g (4.6 oz)cFP-DI-300/301 .................................................................. 100 g (3.6 oz)FP-DI-330 ........................................................................... 133 g (4.7 oz)cFP-DI-330.......................................................................... 103 g (3.7 oz)cFP-DI-304.......................................................................... 193 g (6.81 oz)

[c]FP-DI-300 [c]FP-DI-301 cFP-DI-304 [c]FP-DI-330

OFF State ON State OFF State ON State OFF State ON State OFF State ON State

Input Voltage (V) <5 >15 <5 >15 ≤5 ≥10 ≤1 VDC,≤1 VAC

≥4 VDC, ≥15 VAC (50/60 Hz AC),≥3 VAC (1 KHz AC)Input Current (µA) ≤1000 ≥3000 ≤1000 ≥3000 ≤150 ≥330


4


Power Requirements (from Network Module)[c]FP-DI-300............................................................................ 185 mW[c]FP-DI-301............................................................................ 325 mW[c]FP-DI-330............................................................................ 200 mWcFP-DI-304.............................................................................. 1 W

EnvironmentOperating temperature .......................................................... -40 to 70 °CStorage temperature.............................................................. -55 to 85 °CRelative humidity ................................................................... 10 to 90%, noncondensing

Shock and VibrationThese specifications apply only to Compact FieldPoint. NI recommends Compact FieldPoint if your application is subject to shock and vibration.

Operating vibration, random (IEC 60068-2-64)...................... 10 to 500 Hz, 5 grms

Operating vibration, sinusoidal (IEC 60068-2-6).................... 10 to 500 Hz, 5 gOperating shock (IEC 60068-2-27) ......................................... 50 g, 3 ms half sine, 18 shocks at 6 orientations;

30 g, 11 ms half sine, 18 shocks at 6 orientations

SafetyThis product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use:

• IEC 61010-1, EN 61010-1• UL 61010-1• CAN/CSA-22.2 No. 61010-1

For UL, hazardous location, and other safety certifications, refer to the product label or to ni.com/certification.

Electromagnetic CompatibilityCE, C-Tick, and FCC Part 15 (Class A) Compliant

Emissions ........................................ EN 55011 Class A at 10 m; FCC Part 15A above 1 GHzImmunity ......................................... EN 61326:1997 + A2:2001, Table 1For EMC compliance, operate this device with shielded cabling.

CE ComplianceThis product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows:Low-Voltage Directive (safety)............ 73/23/EECElectromagnetic Compatibility

Directive (EMC) ............................... 89/336/EEC

Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/certification.























system integration.










answers to your questions at ni.com/support. We also offer service programs that provide automatic upgrades to



Hardware Services







ni.com/pxiadvisor.










SERVICE NEEDS

© 2005 National Instruments Corporation. All rights reserved. FieldPoint, National Instruments, National Instruments Alliance Partner, NI, ni.com, NI Developer Suite, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies.A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI. 2005-6214-161-101


ni.com • (800) 813 3693

High-Speed Counter Modules for Compact FieldPoint and FieldPoint

Overview The National Instruments [c]FP-CTR-50x devices are versatile, high-

speed digital counter input modules for Compact FieldPoint and

FieldPoint that can be used to count digital signals ranging from 5 to

30 VDC and to measure frequency. These modules are fast enough to

handle input signals up to 50 kHz for high-speed applications, and

flexible enough to measure frequency using the internal frequency

reference or the external gate inputs. These powerful and versatile

counter modules feature configurable lowpass filters to eliminate

high-frequency noise and cascadable counter channels that can be

used to create counters up to 128 bits wide that will store trillions of

counts. For discrete control applications such as packaging, the

digital output channels can be configured to automatically energize

external devices.

All the modules include onboard diagnostics to ensure trouble-

free installation and maintenance.

Counter ModulesThe CTR-500 and CTR-502 counter modules include eight 16-bit,

50 kHz counters with dedicated clock inputs. For higher resolution

counting, you can combine counter channels to provide cascaded

counters of up to 128 bits. In addition, for each counter, you can set a

terminal count at which the counter automatically rolls over or resets.

For frequency measurement, you can configure each channel to use

any one of the four gate inputs provided. In this mode, you can

enable counting only when the state of the specified gate input is

logic high. By sending the digital pulse train to the gate input and

using the internal reference clock of 1 or 32 kHz, you can measure the

frequency of the incoming pulse train. Because you can read the state

of the gate input, you can also use the four gate inputs as general-

purpose digital input channels.

You can configure each of the four counter outputs to either pulse

or toggle states when you reach the terminal count for a counter

input. This is useful when you need to energize external equipment

upon reaching a particular count for applications like packaging.

You can also use each of the outputs as general-purpose digital outputs.

The CTR-500 modules work with 10 to 30 VDC sourcing devices and

provides sourcing outputs. A sourcing device is one that connects and

disconnect a voltage to the counter module. CTR-500 modules use a

common ground plane for all the digital input channels.

The CTR-502 modules work with 5 to 30 VDC sinking devices and

provides sinking outputs. A sinking device is one that connects and

disconnects a common to the counter module. CTR-502 modules use a

common ground plane for all the digital input channels.

All the channels on the digital input modules feature LEDs that

indicate the input state of each channel.

IsolationCTR-50x modules feature optical bank isolation with 2,300 Vrms of

breakdown isolation. These Compact FieldPoint and FieldPoint

modules do not have channel-to-channel isolation.

• 8 inputs• 5 to 30 VDC inputs • 16-bit counter registers• 50 kHz, maximum• Gate inputs and digital outputs• Cascadable counters for

higher counts• 2,300 Vrms bank isolation for

transient overvoltage protection • Hot swappable with

autoconfiguration • -40 to 70 °C operating range

NI [c]FP-CTR-500, NI [c]FP-CTR-502 NEW

Counter Internal Reference Clock MaximumModule Counter Inputs Input Ranges Inputs Type Resolution Gate Inputs Configurable Outputs for Frequency Measurements Input Frequency[c]FP-CTR-500 8 10 to 30 VDC Sourcing 16 bit, cascadable to 128 bit 4 4 1 and 32 kHz 50 kHz[c]FP-CTR-502 8 5 to 30 VDC Sinking 16 bit, cascadable to 128 bit 4 4 1 and 32 kHz 50 kHz


2 National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • [email protected] • ni.com

Field I/O ConnectionsCompact FieldPoint and FieldPoint modules include a built-in

power distribution bus that provides multiple power connections on

the module. A field-wired power supply connected to the voltage (V)

and common (C) terminals is internally connected to a power

distribution bus that provides additional breakout terminals for

voltage supply (VSUP) and common (COM). These terminals provide

a convenient way to distribute power to field devices that require

external power.

The CTR-500 and CTR-502 have:

• 8 high speed digital counter input terminals (VIN)

• 4 digital gate input terminals (VIN)

• 4 digital output terminals (VOUT)

• 8 common terminals (COM)

• 8 power connections to power field devices (VSUP)

Compact FieldPoint NI cFP-CTR-500..........................................................777318-500NI cFP-CTR-502..........................................................777318-502

Recommended Compact FieldPoint System ProductsNI cFP-2020 ..............................................................777317-2020NI cFP-BP-4 ..................................................................778617-04NI cFP-CB-1 ..................................................................778618-01NI PS-5 power supply ..................................................778805-90NI Developer Suite Professional Control Edition..........777906-03

FieldPoint NI FP-CTR-500 ..........................................................777518-500NI FP-CTR-502 ..........................................................777518-502

Recommended FieldPoint System ProductsNI FP-1601 ....................................................................777792-01NI FP-TB-1 ....................................................................777519-01NI PS-4 power supply ..................................................778586-90NI Developer Suite Standard Control Edition ............777905-03

BUY ONLINE!Visit ni.com/info and enter cfpctr500, cfpctr502, fpctr500,and/or cfpftr502.


To next channel

[c]FP-CTR-500

V C

+ –

COM (Count 0)

VSUP (Count 0)

VIN (Count 0)

10 – 30 VDC ExternalPowerSupply

InputCircuitry

Sourcing-Output Device

Powered by [c]FP-CTR-500

COM (Count 1)

VSUP (Count 1)

VIN (Count 1) InputCircuitry

Sourcing-OutputDevice

VOUT (Out 0)

VSUP (Out 0)

COM (Out 0)

COM (Gate 0)

VSUP (Gate 0)

VIN (Gate 0) InputCircuitry

Switch

Sinking-Input

Device

VOUT (Out 1)

VSUP (Out 1)

COM (Out 1)

Sinking-Input

Device

VOUT (Out 2)

VSUP (Out 2)

COM (Out 2)

Sinking-Input

Device

To next channel

[c]FP-CTR-502

V C

+ –

COM (Count 0)

VSUP (Count 0)

VIN (Count 0)

5 – 30 VDC ExternalPowerSupply

InputCircuitry

COM (Count 1)

VSUP (Count 1)

VIN (Count 1) InputCircuitry


VOUT (Out 0)

VSUP (Out 0)

COM (Out 0)

COM (Gate 0)

VSUP (Gate 0)

VIN (Gate 0) InputCircuitry

VOUT (Out 1)

VSUP (Out 1)

COM (Out 1)

VOUT (Out 2)

VSUP (Out 2)

COM (Out 2)

Sinking-Input

Device


Switch

Load

Powered Load

+

–

ExternalPowerSupply

Figure 1. Wiring Schemtatic for CTR Modules


3National Instruments • Tel: (800) 433-3488 • Fax: (512) 683-9300 • [email protected] • ni.com

Typical for -40 to 70 °C unless otherwise noted.

Input CharacteristicsInput channels .................................................. 12 (8 count, 4 gate)Input type

[c]FP-CTR-500............................................. 10-30 VDC, sinking[c]FP-CTR-502............................................. 5-30 VDC, sourcing

Maximum input voltage ................................... 30 VDCInput threshold level

[c]FP-CTR-500............................................. 8 V typ6 V min10 V max

[c]FP-CTR-502............................................. VSUP – 2.5 V typVSUP – 3.0 V minVSUP – 2.0 V max(VSUP is the external supply voltage)

Input current limiting[c]FP-CTR-500............................................. 5 mA[c]FP-CTR-502............................................. 6 mA

Input bandwidthCount inputs .............................................. 50 kHz or software-enabled 200 kHz lowpass filterGate inputs ................................................ 50 kHz

Maximum off-state leakage current for external devices[c]FP-CTR-500............................................. 0.2 mA[c]FP-CTR-502............................................. 0.3 mA

Output CharacteristicsOutput channels ............................................... 4Output type

[c]FP-CTR-500............................................. 10-30 VDC sourcing, compatible with most 12 and 24 VDC devices

[c]FP-CTR-502............................................. 5-30 VDC sinking, compatible with TTL and other 5, 12, and 24 VDC devices

Supply voltage[c]FP-CTR-500............................................. 10-30 VDC, user-provided[c]FP-CTR-502............................................. 5-30 VDC, user-provided

Maximum output currentFP-CTR-500/502......................................... 1 A per channelcFP-CTR-500/502 ....................................... 1 A per channel at -40 to 50 °C;

0.75 A per channel at 50 to 60 °CMaximum output current on all channels........ 4 AOutput impedance

[c]FP-CTR-500............................................. 0.3 Ω[c]FP-CTR-502............................................. 0.12 Ω

Output bandwidth ............................................ 16 kHz for a current flow ≥3.2 mAMaximum off-state leakage current ................ 25 µA

Power RequirementPower from network module............................ 800 mW


POWER (green) .......................................... Power on and self-test passedREADY (green) ........................................... Module configured and ready

Count inputs <0..7> (green).............................. On/off state of counter inputGate inputs <0..3> (green)................................ On/off state of gate inputOutputs <0..3> (green)...................................... On/off state of outputDimensions (including terminal base).............. 10.7 by 10.9 by 9.1 cm (4.2 by 4.3 by 3.6 in.)Weight

FP-CTR-500/502......................................... 130 g (4.6 oz)cFP-CTR-500/502 ....................................... 100 g (3.5 oz)

Isolation VoltageMaximum isolation voltage ............................. 250 Vrms, Installation Category II Channel-to-channel isolation ........................... No isolation between channelsTransient overvoltage....................................... 2,300 Vrms

EnvironmentOperating temperature

FP-CTR-500/502......................................... -40 to 70 °CcFP-CTR-500/502 ....................................... -40 to 60 °C

Storage temperature ........................................ -55 to 85 °CRelative humidity ............................................. 10 to 90%, noncondensing

Shock and VibrationThese specifications apply only to Compact FieldPoint. NI recommends Compact FieldPoint if your application is subject to shock and vibration. Operating vibration, random

(IEC 60068-2-64) ........................................ 10 to 500 Hz, 5 grms

Operating vibration, sinusoidal (IEC 60068-2-6) .......................................... 10 to 500 Hz, 5 g

Operating shock (IEC 60068-2-27) ........................................ 50 g, 3 ms half sine, 18 shocks at 6 orientations;

30 g, 11 ms half sine, 18 shocks at 6 orientations

SafetyThis product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use:• IEC 61010-1, EN 61010-1• UL 3121-1, UL 61010C-1• CAN/CSA C22.2 No. 1010.1For UL, hazardous location, and other safety certifications, refer to the product label or to ni.com

Electromagnetic CompatibilityCE, C-Tick, and FCC Part 15 (Class A) CompliantEmissions.......................................................... EN 55011 Class A at 10 m FCC Part 15A above 1 GHzImmunity........................................................... EN 61326:1997 + A2:2001, Table 1For EMC compliance, operate this device with shielded cabling.

CE ComplianceThis product meets the essential requirements of applicable European Directives, as amended for CE Marking, as follows:Low-Voltage Directive (safety)......................... 73/23/EECElectromagnetic Compatibility

Directive (EMC).......................................... 89/336/EECRefer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/hardref.nsf/ and search by model number or product line.

Specifications

© 2003 National Instruments Corporation. All rights reserved. Product and company names listed are trademarks or trade names of their respective companies.

Global Services and SupportNI has the services and support to meet your needs around the globe

and through the application life cycle – from planning and

development through deployment and ongoing maintenance – and

tailored for customer requirements in research, design, validation, and

manufacturing. We have direct operations in more than 37 countries

and distributors in another 12 locations. Our local sales and support

representatives are degreed engineers, ready to partner with you to find

solutions that best fit your needs.

Local Sales and Technical SupportIn offices around the globe, our staff is local to the country so that

you have access to field engineers who speak your language and are

available to consult on your unique needs. We also have a worldwide

support organization staffed with Applications Engineers trained to

quickly provide superior technical assistance. Use our online Request

Support interface (ni.com/support) to define your question, then

speak to or e-mail an Applications Engineer, or access more than

14,000 worldwide measurement and automation professionals

within NI Developer Exchange Discussion Forums. ni.com/support

also provides immediate answers to your questions through self-help

troubleshooting, product reference, and application development

resources. For advanced technical support and software maintenance

services, sign up for Premier Support, a program that provides

expanded hours of support availability and

expedited phone/e-mail response time

(typically four business hours).

Training andCertificationNI recognizes that both initial

instruction and ongoing education

contribute to your success. NI provides a

variety of training alternatives, from self-

paced tutorials and interactive CDs, to worldwide

hands-on courses taught by experienced instructors – all designed so

that you can choose how to learn about our products. Further, NI offers

certifications acknowledging individual expertise in working with NI

products and technologies. Visit ni.com/training for more information.

Professional ServicesOur Professional Services team consists of National Instruments

Applications Engineers, NI Consulting Services, and the worldwide

National Instruments Alliance Partner Program (a network of 600

independent consultants and integrators). Our Professional Services

team can offer services ranging from basic start-up assistance and

collaborative development with

your engineers, to turnkey

system integration and

maintenance of your system.

In addition to our NI Alliance Partners, we have developed global

relationships with many industry partners that range from computer

software and hardware companies, such as Microsoft, Dell, Siemens,

and Tektronix. By collaborating with these companies, you receive a

complete spectrum of solutions – from components to turnkey

systems. Find the Alliance Partner directory at ni.com/alliance

Product ServicesNI hardware products are warranted against defects in workmanship

and material for one year from the date of shipment. To help you

meet project life-cycle requirements, NI offers extended warranties

for an additional charge. NI provides complete repair services for our

products. Express repair and advanced replacement services are also

available. Or, order your software and hardware installed in PXI and

PXI/SCXI™ systems with NI Factory Installation Services.

Ordering Made EasyVisit ni.com/products to browse product specifications, make

comparisons, or access technical representatives via online chat or

telephone. Worldwide customers can use a purchase order or credit

card to buy in local currency and receive direct shipments from local

NI offices. Our North American Customer Service Representatives

are available Monday through Friday between 7 a.m. and 7 p.m.

Central Time. Outside North America, please contact the NI office in

your country.

Order Status and Service RequestsNational Instruments brings you real-time status on current orders at

ni.com/status Similarly, find out the status of open technical support

incidents or hardware repair requests at ni.com/support/servicereq

CUSTOMER NEEDS

National Instruments • Tel: (512) 683-0100 • Fax: (512) 683-9300 • [email protected]

ni.com • (800) 433-3488

779463-01

778617-08

777584-01

777318-112

777318-550

777318-500

777318-122

cFP-1808, 8-slot Ethernet/Serial Interface for CompactFieldPoint

cFP-BP-8 8-Slot Backplane

PS-2 Power Supply (US 120 VAC) for FieldPoint Output:24VDC, 0.8A; Input: US 120 VAC

cFP-AI-112 16 ch, 16-Bit Analog Input Module (V)

cFP-DIO-550, Digital Input/Output Module (AC-DC sink/DCsource) 8 channel AC or DC Sinking Digital Input 8 channel DCSourcing Digital Output

cFP-CTR-500, Counter Input Module, 8 channel, externalpower supply optional.

cFP-RTD-122, 16 Bit RTD Input Module (RTD, Ohms), 8channel.

1

1

1

4

1

1

2

$ 999.00

$ 549.00

$ 79.00

$ 599.00

$ 279.00

$ 429.00

$ 469.00

$ 899.10

$ 494.10

$ 71.10

$ 2,156.40

$ 251.10

$ 386.10

$ 844.20

All sales are subject to the enclosed National Instruments terms and conditions of quotation and sale.National Instruments shall not be bound by any conflicting or additional Terms and Conditions. Standardshipping dates are based on product availability at time of quotation and are subject to change withoutnotice. Not all products produced by National Instruments are made in the U.S.A.

Freight Terms :Quote Valid Until :Payment Terms :

NI Weight Based Shipping28-JUN-07Net 30

Please indicate the above quote number when ordering for faster processing.

10%

10%

10%

10%

10%

10%

10%

Total : $ 5,152.98

Andrew NormanUniversity of VirginiaPhysics DepartmentCHARLOTTESVILLE, VA 22903

To ensure the highest quality service in order processing and support after delivery, please provide end-userinformation with your purchase order.

Estimated Delivery Days : 5 - 10 business days ARO.







Phone : 434 9825382

Fax :

National InstrumentsSales Office

11500 N Mopac ExpwyAustin, TX 78759-3504 U.S.A.

Tel : (512) 683-0100 Fax : (512) 683-5794Remit To : P.O. Box # 840909

Dallas, TX 75284-0909www.ni.com

Disc. %List Price Net PriceDescriptionPart NumberQty.Item

Currency quoted in : U. S. Dollars

1

2

3

4

5

6

7

Quotation Date : 05/29/2007

Quotation No. 928105

Shipping and Handling: $ 50.88

http://sine.ni.com/nips/cds/view/p/lang/en/nid/202210







Yours sincerely,National Instruments Corporate

Andrew NormanUniversity of VirginiaPhysics DepartmentCHARLOTTESVILLE, VA 22903 Phone : 434 9825382

Fax :

National InstrumentsSales Office

11500 N Mopac ExpwyAustin, TX 78759-3504 U.S.A.

Tel : (512) 683-0100 Fax : (512) 683-5794Remit To : P.O. Box # 840909

Dallas, TX 75284-0909www.ni.com

Debbie Vasquez

Quotation Date : 05/29/2007