moplatec specs glitter poly
DESCRIPTION
glitter polyTRANSCRIPT
Material Safety data sheet
MOPLATEC GmbH
MODERN PLASTIC TECHNOLOGY
Hagenberg 10 D 07989 TEICHWOLFRAMSDORF - GERMANY
Tel.: +49 (0) 36624 22 55 7
Fax: +49 (0) 36624 22 55 8Handy: +49 (0) 151 587 430 33e-mai: [email protected] Safety data sheetEPOXY - COATED POLYESTER - GLITTER
Properties of Glitter Powder made from 23mic Metallised/Coated Polyester film
1) Mechanical Properties
ItemAsfValueUnitTest conditionTest method
Tensile StrengthMD23KG/MM225CASTM-D882A
TD24KG/MM2
Elongation at BankMD120%
TD110%
Youngs Modulus
MD450KG/MM2
TD500KG/MM2
Impact strength-35KG/CM225CASTM-D1709
Tear StrengthMD14.69AtmosphereASTM-D1922
TD159AtmosphereASTM-D1922
Bursting Strength505KG/CM25CASTM-D774
Folding Endurance15X10CyclesMIT MethodASTM-D2176
MOPLATEC GmbH
MODERN PLASTIC TECHNOLOGY
Hagenberg 10 D 07989 TEICHWOLFRAMSDORF - GERMANY
Tel.: +49 (0) 36624 22 55 7
Fax: +49 (0) 36624 22 55 8Handy: +49 (0) 151 587 430 33e-mai: [email protected] mil 2) Physical Properties
ItemvalueUnitTest
ConditionTest
Method
Density1.4G/m225CASTM-D1505
Water Absorption0.45%25C,24hrAstm-D570
Water Vapor Permeability23G/m2/24hr40C,90% RHASTM-E96
Oxygen Permeability45Cc/m2/24hr/atm24c,1 atmASTM-D1434
3) Thermal Properties
ItemvalueUnitTest
ConditionTest
Method
Melting point1.4G/m225CASTM-D1505
Heat ShrinkageMD1.5150 C/30 min150 C/30minASTM-D2305
TD0.5
Thermal Expansion
Coefficient3x1010-50 C10-50 cASTM-D696
Thermal Expansion
Coefficient3x10---
Specific Heat0.3225 C25 C-
MOPLATEC GmbH
MODERN PLASTIC TECHNOLOGY
Hagenberg 10 D 07989 TEICHWOLFRAMSDORF - GERMANY
Tel.: +49 (0) 36624 22 55 7
Fax: +49 (0) 36624 22 55 8Handy: +49 (0) 151 587 430 33e-mai: [email protected] 4) Optical Properties
ItemvalueUnitTest
ConditionTest
Method
Refractive1.65nD25 CASTM D542
Total Luminous Transmission5%25CASTM D542
Index Haze3%
5) Physical and Chemical Data
Melting Point: 255 265 c (491 477f)
Boiling Point: Not applicable
Colour : Clear, Hazy, White, Yellowish,GOLD,ETC.
Heat of Combustion: 23.5 MJ/Kg
Vapor Density (air =1) : Not applicable
Solubility Gravity: Insoluble
PH: not applicable specific Gravity: 1.40 g/cm
Appearance: Film
Odor: Odorless
Colour: Clear, Hazy, White, Yellowish
MOPLATEC GmbH
MODERN PLASTIC TECHNOLOGY
Hagenberg 10 D 07989 TEICHWOLFRAMSDORF - GERMANY
Tel.: +49 (0) 36624 22 55 7
Fax: +49 (0) 36624 22 55 8Handy: +49 (0) 151 587 430 33e-mai: [email protected]) Fire and Explosion Hazard Data
Flash Point: 346 399 c (655 750F)
Auto ignition Temp: No data
Flammable Limits (STP): Not applicable
Extinguishing Media: Water Spray, Carbon Dioxide, Dry Chemical, Halogenated Agents.
Special Fire Fighting Protective Equipment: Self-contained breathing apparatus with full piece and protective clothing.
Unusual Fire and Explosion Hazards: Film remaining in contact with flame will Ignite and continue to burn slowly, dropping flaming liquid, which can spread the fire. If the flame source is stationary, the fire will shrink away and self-extinguish.
7) Reactive Data
Stability: Stale under normal considers.
Incompatibility (Materials to Avoid): Not applicable.
Hazardous Decomposition Products: combustion products: Carbon Dioxide, Carbon
Monoxide, terephthalic Acid, Aldehdes
Hazardous Polymerization: Will not occur
Health Hazard Assessment
8) General
The health Hazard assessment is based on an evaluation of the chemical composition together with information from a search of the scientific literature and other commercial sources
9) IngestionNot suitable for human consumptionMOPLATEC GmbH
MODERN PLASTIC TECHNOLOGY
Hagenberg 10 D 07989 TEICHWOLFRAMSDORF - GERMANY
Tel.: +49 (0) 36624 22 55 7
Fax: +49 (0) 36624 22 55 8Handy: +49 (0) 151 587 430 33e-mai: [email protected]) Eye Contact
No irritation is likely to develop following contact with human eyes.
11) Skin Contact
No irritation is likely to develop following contact with human skin.
12) Skin Absorption
This product will probably not be absorbed through human skin.
13) First Acid Procedures
No toxic effects are known to be associated with inhalation of dust from this material
13-1-a) skin
Wash material off the skin with plenty of soap and water. If redness, itching or a burning sensation develops, get medical attention.
13-2-b) Eye
Immediately flush with plenty of water. After initial flushing continue flashing for at least 15 minutes if redness, itching or a burning sensation develops, have eye examined and treated by medical personnel.
13-3-c) Ingestion
Give one or two glasses of water to drink. If gastrointestinal symptoms develop consult medical personnel.
13-4-d) Inhalation
Remove victim to fresh air. If cough or other respiratory Systems develop, consult medical personnel.
14) Precautions for Safe Handling and Use
Steps to be taken in case material is released or spilled: Collect for reuse or disposal. Disposal Method: Observe all federal, state and local laws regarding health and pollution.MOPLATEC GmbHMODERN PLASTIC TECHNOLOGY
Hagenberg 10 D 07989 TEICHWOLFRAMSDORF - GERMANY
Tel.: +49 (0) 36624 22 55 7
Fax: +49 (0) 36624 22 55 8Handy: +49 (0) 151 587 430 33e-mai: [email protected]) Control measure
1) Respiratory Protection (Specify Type): None should be needed.
2) Ventilation:
Local Exhaust: Not applicable
Other: Not applicable
3) Protective Clothing: None should be needed
4) Eye Protection: Not applicable
5) Other Protective Equipment: one should be needed
16) CAS NUMBER: Not Applicable
Note: This MSDS in true but only for information, which doesnt mean all coverage related to the product safety matters. MOPLATEC GmbH does not take the responsibility of all damages due to these products.Our application proposals are non-committal and not binding and therefore we cannot be held responsible or liable for any unsuitable application. The suitability of our products has to be tested by our customer prior to each individual application.