jj && valvevalve€¦ · valve manufacturer jj ® ss valvevalve national and regional...
TRANSCRIPT
Metal Seated Metal Seated Plug ValvesPlug Valves
Sizes: 2” Sizes: 2” -- 108”108”
Metal Seated Metal Seated Gate ValvesGate Valves
Sizes: 2” Sizes: 2” -- 108”108”
Lug & Wafer Lug & Wafer Butterfly ValvesButterfly Valves
Sizes: 2” Sizes: 2” -- 24”24”
HedFlex Duckbill HedFlex Duckbill Check ValvesCheck Valves Sizes: 2” Sizes: 2” -- 96”96”
WaStop In LineWaStop In Line Check ValvesCheck Valves
Sizes: 4” Sizes: 4” -- 72”72”
Air/Oil CushionAir/Oil Cushion Lever & WeightLever & Weight
Swing Check ValvesSwing Check Valves Sizes: 2” Sizes: 2” -- 48”48”
Ball Check Ball Check
Check ValvesCheck Valves Sizes: 1/2” Sizes: 1/2” -- 24”24”
®
Valve Manufacturer
®
Stainless SteelStainless Steel
WaferWafer
Phone: 866-498-GATE (4283) ▪ Fax: 281-324-6879 Email: [email protected] ▪ Web Site: www.JandSValve.com
Resilient SeatedResilient Seated Gate Valves Gate Valves
Sizes: 2” Sizes: 2” -- 108”108”
Air CushionAir Cushion Lever & WeightLever & Weight Swing Check Swing Check
ValvesValves Sizes: 2” Sizes: 2” -- 48”48”
A Women’s Business Enterprise
National and Regional Certifications JJ && SS ValveValve
2013
Valve Manufacturer
®
JJ && SS ValveValve
Giving More to the End Users!
J & S Valve located in Huffman, Texas, manufactures gate valves that “improve the industry standards”. The American
Water Works Association (AWWA) Standards C509 and C515 set the minimum design requirements for gate valves. Other gate valve manufacturers strive to design their valve as close to the minimum as possible, and still be in compliance with the standards. J&S Valve manufactures gate valves that exceed the minimum requirements set by the AWWA standards.
One example, the AWWA C509 Standard (the Standard for Resilient Gate Valves), sets the minimum thickness of the body and bonnet and states that the valve can be made of grey iron. J & S Valve improves the standard by exceeding the minimum thickness stated in C509 and manufacturing with cast components of ductile iron (including the body, bonnet, wedge, seal plate, and operating nut). The tensile strength of the J&S cast ductile iron is 65,000 psi with a 12% elongation property. The tensile strength of most grey iron is 30,000 psi with less than 1% elongation.
The AWWA C515 Standard (the Standard for Reduced Wall, Resilient Seated Gate Valves) states, “the valve, the body and the bonnet shall be made of cast ductile iron, except the shell thickness is allowed to be reduced” in some sizes by nearly 50%. J & S feels there is no benefit to the end user when the manufacturers use a material that is twice as strong, but half as thick.
Our Commitment is to providing the highest quality gate valve in the industry. We use higher quality materials rather
than the minimum required by the standards. J&S Valve uses superior materials such as: large diameter stainless steel stems, aluminum bronze stem nuts, fusion bonded epoxy coatings inside and outside, corrosion resistant bolts, and EPDM rubber components. J&S gives the customers a stronger, heavier duty, more reliable and longer lasting gate valve. In addition, J&S offers the most experience in the world when it comes to production of 72” and larger Resilient Seated Gate Valves. J&S maintains an extensive finished-goods inventory of valves 2” - 48.” We provide service to our customers like no other valve manufacturer. J&S has the most complete line of Gate Valves in the world - our sizes range from 2” to 108”. Install Reliability, Install J&S Valves
LOCATIONS
Proud Member
Production Operations: Corporate Office
2323 1st Street 2201 Main St. Ste. 400-9
Huffman, TX 77336 Dallas, TX 75201
Dallas Area
Houston Area 2201 Main St, Dallas
A Women’s Business Enterprise
National and Regional Certifications
2013