ipaso alarms english

0 0

ODU Alarm and Status

Indication Category Descriptions Severity

TXPWR ALM Alarm The TX PWR is lower than 3 dB. MJ

TX INPUT ALM Alarm The TX IF signal become out of range from

-29 dBm 5 dB.

MJ

RXLEV ALM Alarm The reception level become lower than -72dBm ~ -94dBm level.(It

depends on the modulation system and bit rates).

MJ

ODU CPU / Cable

Open Alarm

CPU of ODU is faulty or IF CABLE between IDU - ODU of ODU is broken

or is not connected.

MJ

MUTE STATUS Status Indicates the control status of the ODU TX power output. When the TX

power is set to Mute, Status is issued. -

LO REF Alarm Loss of Ref LO signal of ODU. MN

TX SW Status Status Radio interface TX SW usage state in 1+1 HS Redundant configuration -

ODU ALM Alarm Indicates one of the TXPWR ALM, ODU PS ALM, APC ALM, TPC ALM,

ODU SELF CHECK ALM occurrence MJ

ODU TOTAL ALM Alarm Indicates one of the TXPWR ALM, TX INPUT ALM, RX Level ALM, ODU

CPU/CABLE OPEN ALM, LOREF, ODU ALM occurrence.

Highest

severity will

be displayed

ATPC Power

Mode Status

ATPC control signal fault (90sec) as well as MAX Power continuation

90sec -

ODU TYPE

MISMATCH Alarm

Indicate connected ODU type is not supported at iPASOLINK system, or

ODU type cannot use in provisioned modulation setting. MJ

ODU PS ALM Alarm ALM in a case of Power supply interruption to ODU. MJ

ODUPS SET

STATUS

Status Status indication of the protection switch for ODU power supplies -

1 1

Modem Alarm and Status


Unequipped (MODEM-A) Alarm Reserved and installed optional package is removed from optional slot. MJ

Type Mismatch(MODEM-A) Alarm The equipped type of interface is different from configured type. MJ

Communication FAIL(MODEM-A) Alarm Communication failure of equipment internal control communication. MJ

Module(MODEM-A) Alarm Equipment fault MJ

BUS ERROR TX Alarm Data communication BUS failure condition in TX direction from STM-1 Card. MJ

BUS ERROR RX Alarm Data communication BUS failure condition in RX direction from STM-1 Card. MJ

RXSW STATUS Status Radio interface RX SW usage state in Redundant configuration -

LOSS OF FRAME Alarm Loss of Frame at radio side. MJ

FRAME ID Alarm Frame ID (route differentiation ID) MJ

HIBER ALM Alarm Radio signal degradation (High BER threshold detection). (Threshold :1E-3/1E-4/1E-5) MJ

LOBER ALM Alarm Radio signal degradation (Low BER threshold detection). (Threshold. :1E-6/1E-7/1E-8/1E-9) MN

EARLY WARNING Alarm Radio signal degradation (Early Warning threshold detection). (Threshold :1E-9) MN

MOD Alarm Indicates the operating status of the MOD. When any failure occurs in the modulator section, Alarm is issued. MJ

IF CABLE SHORT Alarm IF cable between IDU - ODU is in short condition. MJ

INPHASE. Status In - Phase indicates the received signal DADE status between No.1 and No.2 MODEM interfaces are in Phase

condition. In this condition, hitless switch over is available.

-

L2SYNC LOSS Alarm Loss of frame synchronization of GFP frames on MODEM port. MJ

RDI Alarm RDI indication reception alarm on MODEM port MJ

UAE. Alarm UAE alarm. Indicates the occurrence of an Unavailable state. MN

TDM/AMR Range Mismatch Alarm Mismatch condition when the mapping number of E1 channels are different between TX and RX modem ports or

mismatch condition of selected RX AMR modulation range and TX AMR modulation range.

MJ

TX SW Reverse Request Status TXSW request signal receiving condition from the opposite station: -

TX SW Lock in Status Status TXSW Lockin state -

Unlocked Alarm Wireless synchronization status of the local side. MJ

MODEM PS OFF Status Indicate power off condition of power switch which is in front of MODEM-A card. -

2 2

STM-1 Alarm and Status


Unequipped (STM1-A) Alarm Reserved and installed optional package is removed from optional slot. MJ

Type Mismatch(STM1-A) Alarm The equipped type of interface is different from configured type. MJ

Communication

FAIL(STM1-A) Alarm Communication failure of equipment internal control communication. MJ

Module(STM1-A) Alarm Equipment fault MJ



SNCP PPS-FAIL Alarm. SNCP Path Protection Failure MJ

SNCP Protection Status Status SNCP Path Protection Status indication which indicates [FS, SF, SD, MS, NR] condition. -

APS Protection Status Status APS Line Protection Status indication which indicates {FS,SF,SD,MS,NR} condition. -

APS Lock-in Status Status APS protection Lock-in Condition. -

SFP_Type Mismatch

(STM1) Alarm Mismatch between SFP on LCT and installed SFP. MJ

SFP Unequipped (STM1) Alarm A SFP is removed. MJ

STM-1LOS Alarm LOS detection on STM-1 Optical port. MJ

STM-1 TF Alarm Transmit Failure detection on STM-1 optical port. MJ

RS LOF Alarm SDH Frame synchronization lost in RS (Regenerator Section) on STM-1 port. MJ

RS TIM Alarm Trace Identifier Mismatch detected in RS (Regenerator Section) on STM-1 port. MJ

RS EXC Alarm B1 Byte error occurrence in RS (Regenerator Section) on STM-1 port. MJ

RS DEG Alarm B1 byte error in RS (Regenerator Section) (RS - Degraded) on STM-1 port. MN

MS AIS Alarm AIS detection in MS (Multiplex Section) on STM-1 port. MJ

MS RDI Alarm Remote Defect Indication reception in MS (Multiplex Section) on STM-1 port. MJ

AU AIS Alarm AIS detection in AU (Administrative Unit) on STM-1 port. MJ

3 3

STM-1 Alarm and Status


AU LOP Alarm Loss of AU pointer happens on STM-1 port. MJ

HP UNEQ Alarm HOP (Higher Order Path) Unequipped occurrence on STM-1 port. MJ

HP TIM Alarm HOP (Higher Order Path) Trace Identifier mismatch occurrence on STM-1 port. MJ

HP-PLM Alarm Payload Label Mismatch occurrence in HOP (Higher Order Path) on STM-1 port. MJ

HP-RDI Alarm RDI (Remote Defect Indication) reception in HOP (Higher Order Path) on STM-1 port. MJ

HP-LOM Alarm Loss of Multi-Frame on STM-1 port. MJ

TU -AIS Alarm In TU (Tributary Unit), AIS detection on STM-1 port. MJ

TU -LOP Alarm Loss of TU Pointer on STM-1 port. MJ

LP -UNEQ. Alarm LP (Lower Order Path) Unequipped occurrence on STM-1 port. MJ

LP RDI Alarm Remote Defect Indicate reception by an LP (Lower Order Path) on STM-1 port. MJ

LP PLM Alarm Payload Label Mismatch Failure occurrence by an LP (Lower Order Path) on STM-1 port. MJ

ALS Status Indication of automatic laser shutdown condition at STM-1 optical port. -

RS UAS Status Status UAS status indication on STM port (Repeater Section) -

STM-1 AIS Generated Status AIS generation condition on STM port. -

PJE Status Pointer justification Event indication at STM port. -

4 4

16E1 alarm and Status


Unequipped (16E1) Alarm Reserved and installed optional package is removed from optional slot. MJ

Type Mismatch(16E1) Alarm The equipped type of interface is different from configured type. MJ

Communication FAIL(16E1) Alarm Communication failure of equipment internal control communication. MJ

Module(16E1) Alarm Equipment fault MJ



E1 LOS Alarm No signal input on E1 port MJ

E1 AIS Status ALARM/Status category can change according to " AIS Received Condition

Setting

MJ / -

Usage Error Alarm Unused E1 CH input signal detection. MN

E1 AIS Generated Status AIS generation condition on every E1 Channels. -

5 5

AUX-A Option Card


Unequipped (AUX-A) Alarm Reserved and installed optional package is removed

from optional slot.

MJ

Type Mismatch(AUX-A) Alarm The equipped type of interface is different from

configured type.

MJ

Communication

FAIL(AUX-A)

Alarm Communication failure of equipment internal control

communication.

MJ

Module(AUX-A) Alarm Equipment fault MJ

BUS ERROR TX Alarm Data communication BUS failure condition in TX

direction from STM-1 Card.

MJ

BUS ERROR RX Alarm Data communication BUS failure condition in RX

direction from STM-1 Card.

MJ

Item Name (Input-x)

Item Name (Cluster-x)

Status/

Alarm

HKA Status Indication {Alarm, Normal} for every

HKA input.

- or

Severity selectable

Item Name (Output-x) Status HKC Status {Alarm, Normal} for every HKC output. -

6 6

GbE-A option card


Unequipped (GBE-A) Alarm Reserved and installed optional package is

removed from optional slot.

MJ

Type Mismatch(GBE-

A)

Alarm The equipped type of interface is different

from configured type.

MJ

Communication

FAIL(GBE-A)

Alarm Communication failure of equipment

internal control communication.

MJ

Module(GBE-A) Alarm Equipment fault MJ

BUS ERROR TX Alarm Data communication BUS failure condition

in TX direction from STM-1 Card..

MJ

BUS ERROR RX Alarm Data communication BUS failure condition

in RX direction from STM-1 Card..

MJ

SFP_Type Mismatch

(ETH)

Alarm Mismatch between SFP on LCT and

installed SFP.

MJ

SFP Unequipped

(ETH)

Alarm A SFP is removed. MJ

LAN LINK Alarm LINK of the LAN Port is disconnected. MJ

Speed & Duplex Status LAN Port setting (Speed&Duplex) -

7 7

Equipment Common alarm and Status-1


MODULE (Main Board) Alarm Equipment fault MJ

BUS ERROR Alarm Data communication BUS failure condition. MJ

Unequipped (PS) Alarm Installed Power Supply Module is removed from PS slot. MJ

Power Supply Alarm Alarm in case of power failure. MJ

FAN Fail Alarm FAN failure MJ

Unequipped (FAN) Alarm Installed FAN Module is removed from FAN slot. MJ

Unequipped (CLK2M) Alarm Installed CLK2M Module is removed from Main Card. MJ

Type Mismatch (CLK2M) Alarm The equipped type of interface is different from configured type. MJ

IDU CPU Alarm Alarm. IDU CPU Alarm MN

Memory Failure Alarm Detection of memory failure MJ

USB Failure Alarm USB memory failure indication MJ

Temperature Alarm The temperature is over the threshold MN

Maintenance Status Maintenance declaration. -

CLK FAIL Alarm Reference Clock Failed. MN

CLK Drift Alarm Reference Clock source Frequency drift condition MN

LTI Alarm Loss of all incoming timing source MJ

CLK Status Changed Status Reference clock change status

(1) (Locked Ref1)

(2) (Locked Ref2)

(3) (Locked Ref3)

(4) Holdover

(5) Freerun

-

SSM FAIL Alarm Received Sync Status Message value is in unstable condition. MN

Quality Level Status Received quality level condition of each timing source. -

Squelch Status The condition of External CLK Output is in squelch condition. -

8 8

Equipment common Alarm and Status -2


EXT CLK Condition Status Condition level of External CLK output. -

EXT CLK LOS Alarm Loss of Signal condition of External clock input. MN

EXT CLK AIS Alarm AIS (Alarm Indication Signal) condition of External Clock input. MN

EXT CLK LOF Alarm Loss of frame condition of External Clock input. MN

EXT CLK Loop Alarm Indication of EXTERNAL clock input is used as EXTERNAL clock output. MJ

Item Name (Input-x)

Item Name (Cluster-x)

Status/

Alarm HKA Status Indication {Alarm, Normal} for every HKA input.

- or Severity

selectable

Item Name (Output-x) Status HKC Status {Alarm, Normal} for every HKC output. -

E1 LOS Alarm No signal input on E1 port MJ

E1 AIS Status

PDH AIS ALARM/Status category can change according to " AIS Received Condition Setting MJ / -

Usage Error Alarm Unused E1 CH input signal detection. MN

E1 AIS Generated Status AIS generation condition on every E1 Channels. -

ETH LOS Alarm LOS detection at Optical Ethernet port. MJ

ETH TF Alarm Transmit Fail detection at Optical Ethernet port. MJ

SFP_Type Mismatch (ETH) Alarm Mismatch between SFP on LCT and installed SFP. MJ

SFP Unequipped (ETH) Alarm A SFP is removed. MJ

LAN LINK Alarm LINK of the LAN Port is disconnected. MJ

Speed & Duplex Status LAN Port setting (Speed&Duplex) -

ETH-OAM LOC Alarm MJ

ETH-OAM Mismerge Alarm Ether OAM Mismatch Detection notice. MN

ETH-OAM Unexpected Period Alarm Ether OAM Unexpected MEP and Ether OAM Unexpected Period detection notice MN

ETH-OAM RDI Alarm Ether OAM RDI reception detection notice MJ

9 9

Equipment common Alarm and Status -3


RSTP New Root Bridge Detect Status The notice in which new RootBridge was detected at the time of SpanningTree processing -

RSTP Topology Changed Status The notice in which a Topology change was detected at the time of SpanningTree processing -

RSTP Protocol Migration Status

The notice which received a Bridge protocol Data Units different in classification of RSTP/STP at the

time of SpanningTree processing -

RSTP Invalid BPDU Received Status Invalid BPDU message at the time of SpanningTree processing -

LLF Message Timeout Status

Loss of a conditional signaling in which the LLF control signal should be received continuously from

the opposite radio equipment.

LLF Status LLF force a LINKDOWN status. The Ethernet port under "edge" mode becomes LINKDOWN. -

IDU TOTAL ALM Alarm IDU TOTAL ALM

The highest

Severity will

be reported

Total FDB Full Status The number of DynamicEntryDynamic Entry in L2Switch has reached the maximum number.

FDB Full Status FDB Full indication specified per VLAN basis.

10

ABBREVIATIONS-1

ACAP Adjacent Channel Alternate

Polarization

ACCP Adjacent Channel Co-Polarization

ACK Acknowledgement

AGC Automatic Gain Control

AIS Alarm Indication Signal

ALM Alarm

ALS Auto Laser Shutdown

AMR Adaptive Modulation Radio

ANT, Ant. Antenna

APS Automatic Protection Switch

ATT Attenuator

ATPC Automatic Transmitter Power Control

AU Administrative Unit

AUX Auxiliary

Ave Average

BBE Background Block Error

BER Bit Error Rate

BPF Band Pass Filter

BS Base Station

BSC Base Station Controller

BTS Base Transceiver Station

CAPEX Capital Expenditure

CBS Committed Burst Size

CCDP Co-Channel Dual Polarization

CCM Continuity Check Message

CEPT Conference of European Postal &

Telecommunication Administration

CIR Committed Information Rate

CKT Circuit

CLK Clock

CMF Channel Mismatch Failure

CMI Coded Mark Inversion

CONV Converter

CORBA Common Object Request Broker

Architecture

CoS Class of Service

CPU Central Processing Unit

CR Critical

CRC Cyclic Redundancy Check

CS Channel Separation

CTRL Control

CV near end Code Violation

CW Carrier Wave

DA Destination Address

DADE Differential Absolute Delay Equalizer

DB Database

DC Direct Current

DCN Data Communication Network

DEG Degraded

DEI Drop Eligible Indicator

DEM Demodulator

Des(Dest) Destination

DI Data-in

DL Download

DM Delay Measurement

DMM Delay Measurement Message

DMR Delay Measurement Reply

DO Data-out

DSCP Differentiated Services Code Point

DUP Duplexer

DXC Digital Cross Connect

E1 E-carrier level 1

EBS Express Burst Size

EIR Excess Information Rate

EMC Electro Magnetic Compatibility

EML Element Management Layer

EMS Element Management System

EOW C Order Wire

EPS ETH-Protection Switch

EQL Equalizer

ERP ETH-Ring Protection Switch

ES Errored Seconds

ETH-CC ETH-Continuity Check function

ETH-LB ETH-Loopback function

ETH-LBM ETH-Loopback Message

ETH-LBR ETH-Loopback Reply

ETH-LB ETH-Loopback function

ETH-LT ETH- Link Trace function

ETH-LTM ETH-Link Trace Message

ETH-LTR ETH-Link Trace Reply

ETH-OAM Ethernet Operations, Administration

and Maintenance

11

ABBREVIATIONS-2

ETH-OAM LB ETH-OAM Loopback

ETH-OAM LT ETH-OAM Link Trace

ETH-RDI ETH-Remote Defect Indication function

ETSI European Telecommunications

Standards Institute

EXC Electrical Cross Connect

E-to-E. End-to-End

Fail Failure

F/B Front Back Ratio

FCS Frame Check Sequence

FDB Forwarding Database

FE Fast Ethernet

FEC Forward Error Correction

FEBBE Far End Background Block Error

FEES Far End Errored Seconds

FESES Far End Severely Errored Seconds

FEUAS Far End Unavailable Seconds

FPGA Field Programmable Gate Array

F/W Firmware

GbE, GBE Gigabit Ethernet

3GPP Third Generation Partnership Project

GUI Graphical User Interface

H Horizontal

HDB High Density Bipolar

HK House Keeping

HP Higher order Path

HYB Hybrid

H/W Hardware

ID Identification

IDU Indoor Unit

IE Internet Explorer

IEC International Electro technical

Commission

IEEE Institute of Electrical and Electronics

Engineers

I/F Interface

IF Intermediate Frequency

IHG iPASOLINK High Grade

IN Input

INTFC Interface

I/O Input/Output

IP Internet Protocol

ITU International Telecommunication Union

ITU-R Radio Communication Sector of ITU

ITU-T Telecommunication Sector of ITU

L2SW Layer2-Switch

LAN Local Area Network

LB Loopback

LBM Loopback Message

LCD Loss of Cell Delineation

LCT Local Craft Terminal

LDPC Low Density Parity Check

LED Light Emitting Diode

Lev. Level

LLF Link Loss Forwarding

LM Loss Measurement

LMM Loss Measurement Message

LNA Low Noise Amplifier

LO Local Oscillator

LOC Loss of Continuity

LOF Loss of Frame

LOM Loss of Multiframe

LOP Loss of Pointer

LO REF Local Reference Signal Loss

LOS Loss of Signal

LP Lower order Path

LPM Link Performance Monitor

LT Link Trace

LTI Loss of incoming Timing Input

LTM Link Trace Message

MAC Media Access Control

MAIN Main

MAINT Maintenance

MAX Maximum

Mdev Mean Deviation

MDCPU MODEM CPU

MDI Medium Dependent Interface

MDIX Medium Dependent Interface

Crossover

MD4 Message Digest Algorithm 4

MD5 Message Digest Algorithm 5

MEG Maintenance Entity Group

MEM Memory

MEP MEG End Point

12

ABBREVIATIONS-3

MIN Minimum

MIP Maintenance Intermediate Point

MIX Mixer

MJ Major

MMC Multi Media Card

MME Mobility Management Entity

MMG Mismerge

MN Minor

MOD Modulator

MODEM Modulator Demodulator

MON Monitor

MPX Multiplexer

MS Multiplex Section

MSC Mobile Switching Center

MSDU MAC Service Data Unit

MSP Multiplex Section Protection

MTBF Mean Time Between Failure

MTPC Manual Transmitter Power Control

MUX Multiplexing Equipment

N/A Not Applicable

NBI Northbound Interface

NE Network Element

NML Network Management Layer

NMS Network Management System

OAM Operation Administration and

Maintenance

OCR Occur

Octs Octets

ODU Out-Door Unit

OFS Out of Frame Second

OMT Ortho-Mode Transducer

OPEX Operational expenditure

OPP Opposite

OPR Operation

OPT Optical

OSPF Open Shortest Path First

OSS Operation Support System

OUT Output

OW Oder Wire

PA Power Amplifier

PBR Pressurizable Type B, flange profile

square Rectangular

PCP Priority Code Point

PDH Plesiochronous Digital Hierarchy

PDU Protocol Data Unit

PGM Program

PHY Physical

PIR Peak Information Rate

PJE Pointer Justification Event

PJE-N Pointer Justification Event Negative Stuff

PJE-P Pointer Justification Event Positive Stuff

PKG Package

Pkts Packets

PLM Payload Label Mismatch

PMC PASOLINK Management Card

PMON Performance Monitor

PNMSj PASOLINK Network Management

System Java Version

PPI PDH PHY Interface

ppm parts per million

PPP Point-to-Point Protocol

PPS Path Protection Switch

PQ Priority Queuing

PRM Parameter

PROT Protection

PS Power Supply

PSC Protection Switching Counts

PSD Protection Switching Duration

PWR Power

QAM Quadrature Amplitude Modulation

QoS Quality of Service

QPSK Quadrature Phase Shift Keying

RCVR Recover

REF Reference

REM Remote

RDI Remote Defect Indication

RF Radio Frequency

RFS Radio Frequency Systems

RL Relay

RMON Remote Network Monitoring

RNC Radio Network Controller

13

ABBREVIATIONS-4

RPL Ring Protection Link

RS Regenerator Section

RS-232 Recommended Standard 232

RSL Received Signal Level

RST Regenerator Section Termination

RSTP Rapid Spanning Tree Protocol

RX Receiver

SC Service Channel

SD Space Diversity

SDH Synchronous Digital Hierarchy

SEG Segment

SEP Severely Errored Period

SES Severely Errored Seconds

SFP Small Form factor Pluggable

SGMI Security Gateway Management

Interface

SMS Synchronous Multiplexing System

SMU Source Measure Unit

SNCP Sub-network Connection Protection

SNMP Simple Network Management Protocol

SP Strict Priority

SPD Speed

SRC Source MAC Address

STAT Status

STD Standard

STM Synchronous Transport Module

STP Spanning Tree Protocol

SUB Substitute

SW Switch

S/W Software

SWG Switch Group

SYNC Synchronous

TCI Tag Control Information

TCN Threshold Crossing Notification

TDM Time Division Multiplex

TDMoP TDM over Packet

TEMP Temperature

TERM Terminal

TF Transmit Fail

TIM Trace Identifier Mismatch

TLV Type Length Value

TM Through Mode

TNC Threaded Neil Councilman

ToS Type of Service

TPID Tag Protocol Identifier

TQC Total Quality Control

TTL Time To Live

TU Tributary Unit

TX Transmitter

UAE UAS Event

UAS Unavailable Seconds

UL Upload

UNEQ Unequipped

UNEXP Unexpected

Unicast DMR Unicast Delay Measurement Reply

UNM Unexpected MEP

UNP Unexpected Period

USB Universal Serial Bus

V Vertical

V Volt

VC Virtual Channel

VLAN Virtual LAN

VP Virtual Path

VPN Virtual Private Network

VSWR Voltage Standing Wave Ratio

WDM Wavelength Division Multiplexing

Web World Wide Web

WG Waveguide

WR Warning

WRR Weighted Round Robin

WS Wayside

XCTRL XPIC Control

X-DEM XPIC Demodulator

XFP 10(X) Gigabit Small Form Factor

Pluggable

XIF XPIC IF

XPD Cross Polarization Discrimination Ratio

XPIC Cross Polarization Interference

Canceller

XREF XPIC Reference

ipaso alarms english

Documents