installation instructions rear vision system â€“ mirror display

INSTALLATION INSTRUCTIONS

1008-9000-00 6 October 2010 1 of 37

Rear Vision System – Mirror Display 2004 onwards Ford F-150 and 2008 onwards Ford Super Duty (Kit part numbers 1008-9520 and 1008-9525) Kit Contents:

RVS Interior (shorter) Harness RVS Chassis (longer) Harness Tailgate Handle with camera and harness Mirror 2 Foam pieces (if needed and optional) 1 bag containing: 25 Short Wire Ties 7 pairs of T taps 1 bag containing:

ZTech (in a white bottle) 1 bag containing:

2 Templates (along with these instructions) 2 Wire Ties (long and optional)

Tools Required:

T20 and T30 Torx Drivers 7mm, 8mm, and 10mm Sockets Flat Head Screwdriver Phillips Screwdriver Plastic Trim tool Drill Bit 1 inch and 1 3/16 inch Center Hole Saws or Sheet Metal Cutters Deburring Tool Soldering Iron Electrical Tape or Heat Shrink Small brush Round file (if needed)


1008-9000-00 6 October 2010 2 of 37

Follow the steps on this page only if you have a rain sensor module mounted on your inside rear view mirror.

1. Remove rain sensor by pulling down and remove connector. (Figure 1)

Figure 1

2. Using a round file open up rain sensor

opening for mirror by 0.46mm so the RVS mirror fits. (Figure 2)

Figure 2


1008-9000-00 6 October 2010 3 of 37

3. Loosen the screw that attaches the existing rear view mirror to the windshield mounting button with a T20 Torx driver. (Figure 3) On some models removing the mirror from the windshield can cause damage to the windshield, so it is highly recommended to contact either a Ford dealership or a windshield replacement company. Otherwise slide the mirror upwards and towards the rear to remove it from the windshield.

Figure 3

4. Remove the connector from the mirror.

(Figure 4)

Figure 4

5. Remove driver’s side dash panel end cap by

pulling away weatherstrip and pull to remove clips from the dash panel. (Figure 5)

Figure 5

6. Remove driver’s side A pillar by pulling with

hands to remove clips from sheet metal. (Figure 6)

Figure 6

7. Remove both sunvisor anchors (either side

of roof console) by removing one screw with a Phillips screw driver. (Figure 7)

Figure 7


1008-9000-00 6 October 2010 4 of 37

8. Remove roof console with hands to remove the clips from the sheet metal. Then remove both connectors. (Figure 8)

Figure 8


1008-9000-00 6 October 2010 5 of 37

9. Pry mirror apart with a screwdriver. (Figure

9).

Figure 9

10. Remove the PC board from the mirror by

disengaging both connectors. (Figure 10)

Figure 10

11. Wrap the mirror PC board in the supplied

foam pieces and cut a hole for the connector terminals. (Figure 11)

Figure 11

Follow the steps on this page if your vehicle has a compass display in the center of dash and a separate mirror compass PC board was not purchased


1008-9000-00 6 October 2010 6 of 37

12. Remove the separate compass module from

the vehicle’s inside mirror by sliding it downwards. (Figure 12)

Figure 12

13. Remove the connector from the compass

module. (Figure 13)

Figure 13

14. Pry the compass module apart with a

screwdriver. (Figure 14)

Figure 14

15. Remove the PC board from the compass

module. (Figure 15)

Figure 15

Follow the steps on this page if your vehicle has a compass display in the cluster


1008-9000-00 6 October 2010 7 of 37

16. Wrap the PC board in the supplied foam

piece and cut a hole for the connector terminals. (Figure 16)

Figure 16

17. Plug the separate compass module

connector into the PC board. (Figure 17)

Figure 17

18. Install the compass module PC board

between underneath the headliner as shown in Figure 18. The connector should face upwards, rearwards and to the right.

Figure 18

Follow the steps on this page if your vehicle has a compass display in the cluster


1008-9000-00 6 October 2010 8 of 37

19. Route the supplied interior harness under

leading edge of the driver’s side headliner by gently separating the headliner from the windshield and tucking the harness into the gap with your fingers. (Figure 19)

19b.Route the supplied interior harness down the driver’s side A pillar. (Figure 19)

Figure 19

19c. Route the supplied interior harness through the A pillar opening. (Figure 20)

Figure 20


1008-9000-00 6 October 2010 9 of 37

Follow the steps on this page only if you have an inside rear view mirror without auto dimming. 19d.Remove passenger side’s sill with a trim tool and remove passenger side’s kick panel with hands

so that the two clips are disengaged from the sheet metal. (See Figures 21 and 22)

Figure 21

Figure 22

19e.Wire the supplied interior harness to the right kick panel connector wires listed in Diagrams A, B,

C, D, E, F, G and H using a soldering iron by following the next three steps (a, b and c). Note: Tape the seven wires at the black connector end of the interior harness and the red and yellow wires at the white connector end of the interior harness back using electrical tape, as they will not be used in this installation process.

a. Route the supplied interior harness green, pink and black wires along the vehicle’s cross dash harness as shown in Figure 23 (using wire ties wherever possible at 2 inch intervals). Place the black ground wire eyelet from the supplied interior harness white connector end between the screw and the sheet metal in the passenger’s side kick panel are as shown in Figure 23 using a 8mm socket.


1008-9000-00 6 October 2010 10 of 37

Follow the steps on this page only if you have an inside rear view mirror without auto dimming.

Figure 23

b. Splice the green reverse wire from the supplied interior harness white connector end to

the wire listed in Diagram A depending on your vehicle year and model. Cover the connection with electrical tape or heat shrink.

c. Splice the pink ignition wire from the supplied interior harness white connector end to the wire listed in Diagram A depending on your vehicle year and model. Cover the connection with electrical tape or heat shrink.

19f.Reinstall passenger’s side kick panel and passenger’s side sill panel with hands.


1008-9000-00 6 October 2010 11 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM A

Non Auto Dimming Pinouts RVS Supplied Interior Harness

Connector Location Pin Color Color F150 2004 Ignition C270J Right Kick 2 W/ L. Blue Pink F150 Reverse C270E Right Kick 20 Black/ Pink Green F150 2005-08 Ignition C270J Right Kick 2 W/ L. Blue Pink F150 Reverse C270B Right Kick 12 Green/ Yellow Green F150 2009-10 Ignition C2280D Right Kick 16 Blue or Blue/ Red Pink F150 Reverse C215 Right Kick 6 Blue Green Super Duty 2008 Ignition C264 Right Kick SJB 10 Red/ Yellow Pink Super Duty Reverse C264 Right Kick SJB 12 Black/ Pink Green Super Duty 2009-10 Ignition C264 Right Kick 2 Blue Pink Super Duty Reverse C264 Right Kick 10 Green/ Blue Green


1008-9000-00 6 October 2010 12 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM B Ignition Connector C270J – 2004 – 2008 F150


1008-9000-00 6 October 2010 13 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM C Reverse Connector C270E – 2004 F150


1008-9000-00 6 October 2010 14 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM D Reverse Connector C270B – 2005-2008 F150


1008-9000-00 6 October 2010 15 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM E Ignition Connector C2280D – 2009-2010 F150


1008-9000-00 6 October 2010 16 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM F Reverse Connector C215 – 2009-2010 F150


1008-9000-00 6 October 2010 17 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM G Ignition and reverse Connector C264 – 2008 Super Duty


1008-9000-00 6 October 2010 18 of 37

INSIDE REAR VIEW MIRROR WITHOUT AUTO DIMMING DIAGRAM H Ignition and reverse Connector C264 – 2009-2010 Super Duty


1008-9000-00 6 October 2010 19 of 37

Follow the steps on this page only if you have an auto dimming inside rear view mirror without Sync.

19g.Connect the supplied interior harness to the vehicle’s mirror harness using the supplied T taps by

the following the next five steps (d, e, f, g and h) and diagram I. Note: Tape the red and yellow wires at the black connector end of the interior harness and all five wires at the white connector end of the interior harness back using electrical tape, as they will not be used in this installation process.

d. Connect the black ground wire from the supplied interior harness black connector end to the wire in pin 4 of the vehicle’s mirror harness connector using supplied T taps (C9044 per Diagram I).

e. Connect the green reverse wire from the supplied interior harness black connector end to the wire in pin 9 of the vehicle’s mirror harness connector using supplied T taps (C9044 per Diagram I).

f. Connect the pink ignition wire from the supplied interior harness black connector end to the wire in pin 1 of the vehicle’s mirror harness connector using supplied T taps (C9044 per Diagram I).

g. Connect the orange positive auto dimming wire from the supplied interior harness black connector end to the wire in pin 11 of the vehicle’s mirror harness connector using supplied T taps (C9044 per Diagram I). Cover the connection with electrical tape or heat shrink.

h. Connect the white negative auto dimming wire from the supplied interior harness black connector end to the wire in pin 15 of the vehicle’s mirror harness connector using supplied T taps (C9044 per Diagram I).


1008-9000-00 6 October 2010 20 of 37

Auto Dimming Mirror Without Sync DIAGRAM I Pinout


1008-9000-00 6 October 2010 21 of 37

Follow the steps on this page only if you have an auto dimming inside rear view mirror with built in Sync microphone.

19h.Connect the supplied interior harness to the vehicle’s mirror harness using the supplied T taps by

the following the next ten steps (i, j, k, l, m, n, o, p, q and r) and Diagram J. Note: Tape black, green and pink wires at the white connector end of the interior harness back using electrical tape, as they will not be used in this installation process.

i. Connect the black ground wire from the supplied interior harness black connector end to the wire in pin 10 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

j. Connect the green reverse wire from the supplied interior harness black connector end to the wire in pin 3 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

k. Connect the pink ignition wire from the supplied interior harness black connector end to the wire in pin 1 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

l. Connect the orange positive auto dimming wire from the supplied interior harness black connector end to the wire in pin 8 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

m. Connect the white negative auto dimming wire from the supplied interior harness black connector end to the wire in pin 7 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

n. Connect the red positive compass wire from the supplied interior harness black connector end to the wire in pin 6 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

o. Connect the yellow negative compass wire from the supplied interior harness black connector end to the wire in pin 2 of the vehicle’s mirror harness connector using supplied T taps (C9012 per Diagram J).

p. Splice the yellow open wire from the microphone harness (supplied separately) to the wire in pin 5 of the vehicle’s mirror harness connector (C9012 per Diagram J). Cover the connection with electrical tape or heat shrink.

q. Splice the black ground wire from the microphone harness (supplied separately) to the wire in pin 10 of the vehicle’s mirror harness connector (C9012 per Diagram J). Cover the connection with electrical tape or heat shrink.

r. Splice the blue 12V positive wire from the microphone harness (supplied separately) to the wire in pin 4 of the vehicle’s mirror harness connector (C9012 per Diagram J). Cover the connection with electrical tape or heat shrink.

s. Place the microphone in a convenient place (A pillar) on headliner.


1008-9000-00 6 October 2010 22 of 37

Auto Dimming With Built In Sync Microphone Mirror DIAGRAM J Pinout


1008-9000-00 6 October 2010 23 of 37

Follow the steps on this page only if you have an auto dimming inside rear view mirror with a separate Sync microphone (in the headliner).

19i.Wire the supplied interior harness to the vehicle’s mirror harness using a soldering iron by the

following the next seven steps (t, u, v, w, x, y and z) and Diagrams K and L. Note: Tape black, green and pink wires at the white connector end of the interior harness back using electrical tape, as they will not be used in this installation process process.

t. Connect the black ground wire from the supplied interior harness black connector end to the wire listed in either Diagram K (pin 2) or L (pin 3) depending on your vehicle make and model using supplied T taps.

u. Connect the green reverse wire from the supplied interior harness black connector end to the wire listed in either Diagram K (pin 3) or L (pin 2) depending on your vehicle make and model using supplied T taps.

v. Connect the pink ignition wire from the supplied interior harness black connector end to the wire listed in either Diagram K (pin 1) or L (pin 1) depending on your vehicle make and model using supplied T taps.

w. Connect the orange positive auto dimming wire from the supplied interior harness black connector end to the wire listed in either Diagram K (pin 4) or L (pin 4) depending on your vehicle make and model using supplied T taps.

x. Connect the white negative auto dimming wire from the supplied interior harness black connector end to the wire listed in either Diagram K (pin 5) or L (pin 5) depending on your vehicle make and model using supplied T taps.

y. Connect the red positive compass wire from the supplied interior harness black connector end to the wire in pin 6 of the vehicle’s mirror harness connector (Connector 911 per Diagram L) using supplied T taps.

z. Connect the yellow negative compass wire from the supplied interior harness black connector end to the wire in pin 7 of the vehicle’s mirror harness connector (Connector 911 per Diagram L) using supplied T taps.


1008-9000-00 6 October 2010 24 of 37

Auto Dimming With Separate Sync Microphone Mirror DIAGRAM K 2004-2007 F150 Pinout


1008-9000-00 6 October 2010 25 of 37

Auto Dimming With Separate Sync Microphone Mirror DIAGRAM L 2008-2010 F150 and Super Duty Pinout


1008-9000-00 6 October 2010 26 of 37

Camera, Interior, and Chassis Harness Pinout Reference Diagram M

PIN NO NAME CAMERA HARNESS COLOR

CHASSIS & INTERIOR HARNESS COLOR

1 VIDEO SIGNAL YELLOW GRAY/DARK BLUE 2 SHIELD WHITE WHITE 3 BACKUP LAMP BLUE GREEN 4 VIDEO GND BROWN GRAY/ORANGE 5 POWER GND BLACK BLACK 6 IGNITION RED PINK


1008-9000-00 6 October 2010 27 of 37

Supplied Mirror Pinout Reference Diagram DIAGRAM N

PIN Circuit Description 1 Camera NTSC Video (+) 2 Camera NTSC Video (-) 3 Camera Video Shield 4 Camera Power (+) 5 Dual Outside Drive EC (+) 6 Not Used 7 Not Used 8 Vehicle Ground (-) 9 Reverse Input (Active High)

10 Camera Power (-) 11 Not Used 12 Not Used 13 Ignition (Run Only Line) 14 Not Used 15 Not Used 16 Dual Outside Drive EC (-)


1008-9000-00 6 October 2010 28 of 37

20. Reinstall both sunvisor anchors with their screws using a Phillips screwdriver.

21. Reinstall roof console by engaging both connectors and inserting back into the headliner until all clips are seated.

22. Plug the supplied interior harness connector into the back of the supplied mirror. (Figure 24)

Figure 24

23. Install the supplied mirror by placing over the windshield mounting button and sliding it forward. Use a T20 Torx driver to tighten the screw on the mirror mount.

24. If equipped, reengage rain sensor connector to rain sensor and seat modified rain sensor to the supplied mirror base.

25. Reinstall A pillar while routing the supplied interior harness above A pillar clips.

26. Cut off the connector from the vehicle’s mirror harness leaving enough wire on the connector end to splice onto. (Figure 25)

Figure 25


1008-9000-00 6 October 2010 29 of 37

27. Using a soldering iron, splice the black

ground wire from the supplied interior harness white connector end to the either wire from pin 3 of the vehicle’s mirror harness connector (C911 per Diagram I) or the wire from pin 10 of the vehicle’s mirror harness connector (C9012 per Diagram H) depending on your vehicle’s mirror . Cover the connection with electrical tape or heat shrink.

28. Using a soldering iron, splice the green reverse wire from the supplied interior harness white connector end to the either wire from pin 2 of the vehicle’s mirror harness connector (C911 per Diagram I) or the wire from pin 3 of the vehicle’s mirror harness connector (C9012 per Diagram H) depending on your vehicle’s mirror . Cover the connection with electrical tape or heat shrink.

29. Using a soldering iron, splice the pink ignition wire from the supplied interior harness white connector end to the either wire from pin 1 of the vehicle’s mirror harness connector (C911 per Diagram I) or the wire from pin 1 of the vehicle’s mirror harness connector (C9012 per Diagram H) depending on your vehicle’s mirror . Cover the connection with electrical tape or heat shrink.

30. Using a soldering iron, splice the red positive compass wire from the supplied interior harness white connector end to the either wire from pin 6 of the vehicle’s mirror harness connector (C911 per Diagram I) or the wire from pin 6 of the vehicle’s mirror harness connector (C9012 per Diagram H) depending on your vehicle’s mirror . Cover the connection with electrical tape or heat shrink.

31. Using a soldering iron, splice the yellow negative compass wire from the supplied interior harness white connector end to the either wire from pin 7 of the vehicle’s mirror harness connector (C911 per Diagram I) or the wire from pin 2 of the vehicle’s mirror harness connector (C9012 per Diagram H) depending on your vehicle’s mirror . Cover

the connection with electrical tape or heat shrink.

32. Plug connector into the mirror PC board. (Figure 26)

Figure 26

33. Remove driver’s side knee bolster by

removing three screws with a M7 socket. (Figure 27)

Figure 27

34. Remove driver’s side knee bolster

reinforcement by removing four screws with a M8 socket (Figure 28)

Follow the steps on this page if your vehicle has a compass display in the center of dash


1008-9000-00 6 October 2010 30 of 37

Figure 28

35. Route the mirror PC board connector as

shown. (Figure 29)

Figure 29

36. Place the mirror PC board as shown (with its

connector facing forward and towards the bottom). Then install both longer straps around board and vehicle’s cross dash harness. (Figure 30)

Figure 30

37. Reinstall driver’s side knee bolster

reinforcement with the four screws using a M8 socket.

38. Reinstall driver’s side knee bolster with three screws using a M7 socket.

Follow the steps on this page if your vehicle has a compass display in the center of dash


1008-9000-00 6 October 2010 31 of 37

39. Remove driver’s side sill plate with a trim tool. (Figure 31)

Figure 31

40. Loosen driver’s side A pillar lower molding with hands and then remove driver’s side lower kick panel with hands so that the two clips are disengaged from the sheet metal (Figure 32).

Figure 32

41. Pull back carpet in front of driver’s seat.

(Figure 33) 42. If area underneath carpet looks like figure

37 place template number 1008-9100-01 (Super Duty) over opening in front of driver’s seat. (Figure 33)

43. If area underneath carpet looks like figure 34 place template number 1008-9100-02 (F-150) over hole covered in tape in front of driver’s seat. (Figure 35)

Figure 33

Figure 34

Figure 35

44. Drill a pilot hole. Then use a hole cutter to

drill a 1 inch hole. (Figure 36) 45. Clean the rough edges with a deburring

tool. (Figure 36)


1008-9000-00 6 October 2010 32 of 37

Figure 36

46. Apply Z-tech with a small brush. (Figure 37)

Figure 37

47. Route grommet end of chassis harness

through drilled hole. (Figure 38)

Figure 38

48. Seat grommet onto drilled hole. (Figure 39)

Figure 39

49. Route chassis harness as shown. (Figure 40)

Figure 40

50. Connect the chassis harness connector to

the interior harness connector. (Figure 41)

Figure 41

51. Reinstall the green locking tab. 52. Reinstall driver’s side dash panel end cap

with hands.


1008-9000-00 6 October 2010 33 of 37

53. Reinstall driver’s side kick panel with hands. 54. Reinstall driver’s sill panel with hands. 55. Reinstall driver’s side door weatherstrip with

hands. 56. Route chassis harness along existing vehicle

chassis harness and over fuel tank and wire tie every two inches. (Figures 42 and 43)

Figure 42

Figure 43

57. Loop any excess length and wire tie to

vehicle’s chassis harness as shown. (Figure 44)

Figure 44

58. Lower tailgate and take off upper sheet

metal cover by removing eight screws with a T30 torx driver. (Figure 45)

Figure 45

59. Take off tailgate handle by removing two

nuts with a 10mm socket. (Figure 46)

Figure 46


1008-9000-00 6 October 2010 34 of 37

60. Remove tailgate straps from pickup box with a screwdriver. (Figure 47)

Figure 47

61. Take off tailgate by lifting away from lower tension pins. Place tailgate on a clean flat surface. (Figure 48)

Figure 48

62. Take off lock cylinder from tailgate handle,

which was removed from the vehicle, by pulling out spring clip. (Figure 49)

Figure 49

63. Install lock cylinder into supplied tailgate

handle with camera by pushing in cylinder to handle.

64. Route camera harness through handle opening in tailgate to the hole in the bottom of the tailgate. (Figure 50)

Figure 50

65. Install supplied tailgate handle with camera into tailgate by tightening two nuts with 10mm socket. (Figure 51)


1008-9000-00 6 October 2010 35 of 37

Figure 51

66. Reinstall tailgate upper sheet metal with

eight screws using a T30 torx driver. (Figure 52)

Figure 52


1008-9000-00 6 October 2010 36 of 37

Figure 53

67. Make a temporary mark on the tailgate bed

that is 21 inches from the left side and 1 ¼ inches from the top as shown in figures 54 and 55.

Figure 54

Figure 55

68. Drill a pilot hole. Then use a hole cutter to drill a 1 3/16 inch hole. (Figure 56)

Figure 56

69. Clean the rough edges with a deburring

tool. (Figure 57)

Figure 57

70. Apply Z-tech with a small brush. (Figure 58)

Figure 58

Follow the steps on this page if your vehicle does not have a hole in the tailgate per figure 53


1008-9000-00 6 October 2010 37 of 37

71. Reinstall tailgate to left tension pin on tailgate bed.

72. Route camera harness through drilled hole in tailgate bed. (Figure 59)

Figure 59

73. Reinstall tailgate to right tension pin on tailgate bed.

74. Reinstall tailgate to both tailgate straps. 75. Seat camera harness grommet in drilled

tailgate bed hole. (Figure 60)

Figure 60

76. Plug the camera wiring harness connector

into the chassis wiring harness connector. (Figure 61)

Figure 61

77. Start the vehicle and put it into reverse in order to check that all connections were made properly. If all of the connections are correct you will see an image displayed on the left side of the supplied mirror.

installation instructions rear vision system â€“ mirror display

Documents