iglide® H• Can be used underwater

• For high temperatures

• Resistant to chemicals

• High load capabilities

369

Underwater applications

Maintenance-free

Resistant to chemicals

For high temperatures

iglide®

H iglide® H - UniversalHigh temperature and chemical resistance

l Suitable for underwater applicationsl When high temperature resistance is necessaryl For high mechanical loadingl For applications in contact with chemicals

l When extremely high wear resistance underwater is needed

➤ iglide® H370l When universal resistance to chemicals is needed ➤ iglide® T500l For the maximum pressure at higher temperatures ➤ iglide® T500 ➤ iglide® Z

Suitable for temperatures up to 392°F. Very low coefficients of friction when used with hardened shafts.

max. +392°Fmin. –40°FF

Available from stock Detailed information about delivery time online.

Ø 3 to 70 mmmore dimensions on request

mm

Typical application areas

Price breaks online No minimum order.$

Lifetime calculation, configuration and more ➤ www.igus.com/H370

l Offshorel Marine engineeringl Beverage technology

l Medicall Mechatronics

iglide®

H

3713D-CAD files, prices and delivery time ➤ www.igus.com/H

iglide® H - Technical Data

Material Properties Table

General Properties Unit iglide® H Testing MethodDensity g/cm3 1.71Color grayMax. moisture absorption at 73°F / 50% r.h. % weight 0.1 DIN 53495Max. moisture absorption % weight 0.3Coefficient of friction, dynamic against steel µ 0.07 - 0.20pv value, max. (dry) psi x fpm 39,000

Mechanical PropertiesModulus of elasticity psi 1,813,000 DIN 53457Tensile strength at 68°F psi 25,380 DIN 53452Compressive strength psi 11,750Permissible static surface pressure (68°F) psi 13,050Shore D-hardness 87 DIN 53505

Physical and Thermal PropertiesMax. long-term application temperature °F 392Max. application temperature, short-term °F 464Min. application temperature °F -40Thermal conductivity W/m x K 0.60 ASTM C 177Coefficient of thermal expansion K-1 x 10-5 4 DIN 53752

Electrical PropertiesSpecific volume resistance Ωcm < 105 DIN IEC 93Surface resistance Ω < 102 DIN 53482

1,96919719.7.1971.45

1,450

14,500

14.50

1.97

Surface Speed (fpm)

Pre

ssur

e (p

si)

Permissible pv value for iglide® H running dry against a steel shaft, at 68°F

Compressive StrengthThe graph shows the elastic deformation of iglide® H for radial loads. At the recommended surface pressure of 13,050 psi, the deformation is approximately 2.5% at room temperature.

➤ Compressive strength, Page 63

Deformation under load and temperature

1.0

1.5

2.0

2.5

3.0

3.5

0.00 3,626 7,252 10,880 14,500

0.5

Def

orm

atio

n (%

)

Pressure (psi)

140°F 73°F

Maximum surface speeds

Permissible Surface Speedsiglide® H is suitable for continuous running speeds of 196 fpm (rotating) to 590 fpm (linear). Linear movements allow higher running speeds since a larger area of the shaft contributes to cooling.

➤ Surface speed, Page 64 ➤ pv value, Page 65

Continuous Short Term

fpm fpm

Rotating 196 295

Oscillating 137 216

Linear 590 787

372

iglide®

H

Lifetime calculation, configuration and more ➤ www.igus.com/H

iglide® H - Technical Data

0.1

0.2

0.3

0.4

9.84 19.69 29.53 39.37 49.21 59.06 68.90 78.74

Co

effic

ient

of

fric

tion

(µ)

Surface Speed (fpm)

0.00

0.05

0.10

0.15

0.20

14500 2901 4351 5802 7252 8702 1160010150

Co

effic

ient

of

fric

tion

(µ)

Pressure (psi)

Coefficients of friction for iglide® H against steel (Shaft finish = 40 rms, 50 HRC)

Coefficients of friction for iglide® H as a result of the load, v =1.97 fpm

Coefficients of friction for iglide® H as a result of the surface speed; p =108 psi

Friction and WearBoth the wear rate and the coefficient of friction values change depending on the pressure. Interestingly, the coefficient of friction µ lowers slightly with the increase of surface speed at constant load. See charts below.

➤ Coefficients of friction and surfaces, Page 68 ➤ Wear resistance, Page 69

Temperature limits for iglide® H

Temperaturesiglide® H is an extremely temperature-resistant material. With a maximum permissible short-term temperature of 464°F, iglide® H plain bearings may be used in applications with high heat at low loads.With increasing temperatures, the compressive strength of iglide® H plain bearings decreases. The graph to the right shows this relationship. The ambient temperatures prevalent in the bearing system also have an effect on the bearing wear.

➤ Application temperatures, Page 67 68 122 176 302 3920

2,901

5,802

8,702

11,600

23,210

17,400

20,310

14,500

248

Pre

ssur

e (p

si)

Temperature (°F)

Recommended permissible maximum static surface pressure of iglide® H as a result of the temperature

iglide® H Application Temperature

Minimum - 40°F

Max. long-term +392°F

Max. short-term +464°F

Additional axial securing +248°F

iglide® H Coefficient of Friction

Dry 0.07 - 0.20

Grease 0.09

Oil 0.04

Water 0.04

iglide®

H

3733D-CAD files, prices and delivery time ➤ www.igus.com/H

iglide® H - Technical Data

Wear of iglide® H, rotating application with different shaft materials, p=108 psi, v=98 fpm

Wear for oscillating and rotating applications with different shaft materials p = 290 psi

6

15

18

0

12

3

9

Har

d a

nod

ized

alu

min

um

Aut

om

atic

scr

ew s

teel

1050

1050

, har

d c

hro

med

HR

Car

bo

n S

teel

304

Sta

inle

ss

440B

Wea

r (µ

m/k

m)

0

5

10

15

20

25

30

35

40

45

Wea

r (µ

m/k

m)

1050steel

Oscillating Rotating

Hardchromed

304 Stainlesssteel

HR carbonsteel

Installation Tolerancesiglide® H plain bearings are oversized before being pressfit. After proper installation into a recommended housing bore, the inner diameter adjusts to meet our specified tolerances. Please adhere to the catalog specifications for housing bore and recommended shaft sizes. This will help to ensure optimal performance of iglide® plain bearings.

➤ Tolerance table, Page 75 ➤ Testing methods, Page 76

.0197”(0.5 mm)

b1

A

30°

f

A

Length of chamfer Length30°

Shaft MaterialsThe graphs show results of testing different shaft materials with plain bearings made of iglide® H. The results clearly show that in rotating and oscillating applications the correct shaft selection is critical.For rotating applications, shafts made of 1050 hardened, ground steel and HR Carbon steel show the best wear values, the 304 stainless steel shaft is best suited for oscillating movements. Also, hard chromed shafts with iglide® H bearings are only recommended for low loads. If the shaft material you plan to use is not contained in this list, please contact us.

➤ Shaft Materials, Page 71

Wear of iglide® H with different shaft materials in rotating applications

0

1

2

3

4

5

6

0 145 290 435 725580

Pressure (psi)

Wea

r (µ

m/k

m)

304 Stainless1050 Steel HR carbon steel Hard chromed

For Inch Size Bearings

Length Tolerance (b1)Length of Chamfer (f)

Based on d1Length(inches)

Tolerance (h13)(inches)

0.1181 to 0.2362 -0.0000 /-0.0071 f = .012 ➝ d1 .040” - .236”

f = .019 ➝ d1 > .236” - .472”

f = .031 ➝ d1 > .472” - 1.18”

f = .047 ➝ d1 > 1.18”

0.2362 to 0.3937 -0.0000 /-0.00870.3937 to 0.7086 -0.0000 /-0.01060.7086 to 1.1811 -0.0000 /-0.01301.1811 to 1.9685 -0.0000 /-0.01541.9685 to 3.1496 -0.0000 /-0.0181

For Metric Size Bearings

Length Tolerance (b1)Length of Chamfer (f)

Based on d1Length

(mm)Tolerance (h13)

(mm)

1 to 3 -0 /-140 f = 0.3 ➝ d1 1 - 6 mmf = 0.5 ➝ d1 > 6 - 12 mmf = 0.8 ➝ d1 > 12 - 30 mmf = 1.2 ➝ d1 > 30 mm

> 3 to 6 -0 /-180> 6 to 10 -0 /-220>10 to 18 -0 /-270>18 to 30 -0 /-330>30 to 50 -0 /-390>50 to 80 -0 /-460

374

iglide®

H

Lifetime calculation, configuration and more ➤ www.igus.com/H

iglide® H - Technical Data

Radiation Resistanceiglide® H plain bearings are resistant to radiation up to an intensity of 2 x 102 Gy. They also withstand neutron and gamma particle radiation.

Electrical Propertiesiglide® H plain bearings are electrically conducting.

VacuumFor use in a vacuum environment, it must be taken into account that a small amount of moisture is released as vapor.

UV Resistanceiglide® H plain bearings are only conditionally resistant against UV radiation. Under the effects of weathering, the surface of iglide® H becomes rougher, and the compressive strength of the material decreases.

Chemical Resistanceiglide® H plain bearings have a good chemical resistance. Even aggressive chemicals can act as lubricants. Plain bearings made of iglide® H are not resistant to hot, oxidizing acids.The moisture absorption of iglide H plain bearings is below 0.1% in standard atmosphere. The saturation limit in water is 0.3%. iglide® H does not swell and therefore is very well suited for use in wet surroundings

➤ Chemical table, Page 1364

Chemical resistance of iglide® HAll data given concerns the chemical resistance at room temperature (68°F). For a complete list, see Page 1364

Medium Resistance

Alcohol +

Hydrocarbon +

Greases, oils without additives +

Fuels +

Weak acids + to 0

Strong acids + to –

Weak alkaline +

Strong alkaline +

+ resistant, 0 conditionally resistant, – not resistant

Electrical properties of iglide® H

iglide® H

Specific volume resistance < 105 Ωcm

Surface resistance < 102 Ω

iglide®

H

375

iglide® H - Product RangeSleeve bearing - Metric

Type Dimensions

H S M -03 04-05

iglid

e® m

ater

ial

Form

S (s

leev

e)

Met

ric

Inne

r-Ø

d1

(mm

)

Out

er-Ø

d2

(mm

)

Leng

th b

1 (m

m)

Order key

0.5 mm

30°

fb1

d1

d2AA

30° For tolerance values please refer to page 373

Dimensions according to ISO 3547-1 and special dimensions*Based on steel housing bore

3D-CAD files, prices and delivery time ➤ www.igus.com/H

Part Number d1 d2 b1 I.D. After Pressfit* Housing Bore Shaft Size

h13 Min. Max. Min. Max. Min. Max.

HSM-0304-03 3.0 4.5 3.0 3.006 3.046 4.500 4.512 2.975 3.000

HSM-0405-04 4.0 5.5 4.0 4.010 4.058 5.500 5.512 3.970 4.000

HSM-0507-05 5.0 7.0 5.0 5.010 5.058 7.000 7.015 4.970 5.000

HSM-0608-03 6.0 8.0 3.06.010 6.058

8.000 8.015 5.970 6.000

HSM-0608-06 6.0 8.0 6.0 8.000 8.015 5.970 6.000

HSM-0810-08 8.0 10.0 8.08.013 8.071

10.000 10.015 7.964 8.000

HSM-0810-10 8.0 10.0 10.0 10.000 10.015 7.964 8.000

HSM-1012-06 10.0 12.0 6.010.013 10.071

12.000 12.018 9.964 10.000

HSM-1012-10 10.0 12.0 10.0 12.000 12.018 9.964 10.000

HSM-1214-10 12.0 14.0 10.0

12.016 12.086

14.000 14.018 11.957 12.000

HSM-1214-12 12.0 14.0 12.0 14.000 14.018 11.957 12.000

HSM-1214-15 12.0 14.0 15.0 14.000 14.018 11.957 12.000

HSM-1214-20 12.0 14.0 20.0 14.000 14.018 11.957 12.000

HSM-1416-20 14.0 16.0 20.0 14.016 14.086 16.000 16.018 13.957 14.000

HSM-1517-15 15.0 17.0 15.0 15.016 15.086 17.000 17.018 14.957 15.000

HSM-1618-15 16.0 18.0 15.0

16.016 16.086

18.000 18.018 15.957 16.000

HSM-1618-20 16.0 18.0 20.0 18.000 18.018 15.957 16.000

HSM-1618-25 16.0 18.0 25.0 18.000 18.018 15.957 16.000

HSM-1820-15 18.0 20.0 15.018.016 18.086

20.000 20.021 17.957 18.000

HSM-1820-25 18.0 20.0 25.0 20.000 20.021 17.957 18.000

HSM-2023-20 20.0 23.0 20.020.020 20.104

23.000 23.021 19.948 20.000

HSM-2023-30 20.0 23.0 30.0 23.000 23.021 19.948 20.000

HSM-2225-20 22.0 25.0 20.0 22.020 22.104 25.000 25.021 21.948 22.000

HSM-2528-15 25.0 28.0 15.025.020 25.104

28.000 28.021 24.948 25.000

HSM-2528-20 25.0 28.0 20.0 28.000 28.021 24.948 25.000

HSM-3034-20 30.0 34.0 20.0

30.020 30.104

34.000 34.025 29.948 30.000

HSM-3034-30 30.0 34.0 30.0 34.000 34.025 29.948 30.000

HSM-3034-40 30.0 34.0 40.0 34.000 34.025 29.948 30.000

HSM-3236-30 32.0 36.0 30.0 32.025 32.125 36.000 36.025 31.938 32.000

HSM-3539-40 35.0 39.0 40.0 35.025 35.125 39.000 39.025 34.938 35.000

HSM-4044-20 40.0 44.0 20.040.025 40.125

44.000 44.025 39.938 40.000

HSM-4044-50 40.0 44.0 50.0 44.000 44.025 39.938 40.000

HSM-4550-30 45.0 50.0 30.0 45.025 45.125 50.000 50.025 44.938 45.000

HSM-5055-40 50.0 55.0 40.0 50.025 50.125 55.000 55.030 49.938 50.000

HSM-5560-26 55.0 60.0 26.0 55.030 55.150 60.000 60.030 54.926 55.000

HSM-6065-60 60.0 65.0 60.0 60.030 60.150 65.000 65.030 59.926 60.000

HSM-7075-50 70.0 75.0 50.0 70.030 70.150 75.000 75.030 69.926 70.000

376

iglide®

R

Lifetime calculation, configuration and more ➤ www.igus.com/H

iglide®

H

r = max. 0.5

iglide® H - Product RangeFlange bearing - Metric

d3

d1

d2

b1r

30°

f

A A

b2 For tolerance values please refer to page 373

Type Dimensions

H F M -03 04-05

iglid

e® m

ater

ial

Form

F (fl

ange

)

Met

ric

Inne

r-Ø

d1

(mm

)

Out

er-Ø

d2

(mm

)

Leng

th b

1 (m

m)

Order key

Dimensions according to ISO 3547-1 and special dimensions*Based on steel housing bore

Part Number d11) d2 d3 b1 b2 I.D. After Pressfit* Housing Bore Shaft Size

d13 h13 -0.14 Min. Max.. Min. Max. Min. Max.

HFM-0405-04 4.0 5.5 9.5 4.0 0.75 4.010 4.058 5.500 5.512 3.970 4.000

HFM-0507-05 5.0 7.0 11.0 5.0 1.05.010 5.058

7.000 7.015 4.970 5.000

HFM-0507-08 5.0 7.0 11.0 8.0 1.0 7.000 7.015 4.970 5.000

HFM-0608-04 6.0 8.0 12.0 4.0 1.0

6.010 6.058

8.000 8.015 5.970 6.000

HFM-0608-06 6.0 8.0 12.0 6.0 1.0 8.000 8.015 5.970 6.000

HFM-0608-10 6.0 8.0 12.0 10.0 1.0 8.000 8.015 5.970 6.000

HFM-0810-07 8.0 10.0 15.0 7.0 1.0

8.013 8.071

10.000 10.018 7.964 8.000

HFM-0810-10 8.0 10.0 15.0 10.0 1.0 10.000 10.018 7.964 8.000

HFM-0810-15 8.0 10.0 15.0 15.0 1.0 10.000 10.018 7.964 8.000

HFM-1012-04 10.0 12.0 18.0 4.0 1.0

10.013 10.071

12.000 12.018 9.964 10.000

HFM-1012-09 10.0 12.0 18.0 9.0 1.0 12.000 12.018 9.964 10.000

HFM-1012-15 10.0 12.0 18.0 15.0 1.0 12.000 12.018 9.964 10.000

HFM-1012-20 10.0 12.0 18.0 20.0 1.0 12.000 12.018 9.964 10.000

HFM-1214-07 12.0 14.0 20.0 7.0 1.0

12.016 12.086

14.000 14.018 11.957 12.000

HFM-1214-10 12.0 14.0 20.0 10.0 1.0 14.000 14.018 11.957 12.000

HFM-1214-15 12.0 14.0 20.0 15.0 1.0 14.000 14.018 11.957 12.000

HFM-1416-12 14.0 16.0 22.0 12.0 1.0 14.016 14.086 16.000 16.018 13.957 14.000

HFM-1517-17 15.0 17.0 23.0 17.0 1.0 15.016 15.086 17.000 17.018 14.957 15.000

HFM-1618-13 16.0 18.0 24.0 13.0 1.016.016 16.086

18.000 18.018 15.957 16.000

HFM-1618-17 16.0 18.0 24.0 17.0 1.0 18.000 18.018 15.957 16.000

HFM-1820-17 18.0 20.0 26.0 17.0 1.0 18.016 18.086 20.000 20.021 17.957 18.000

HFM-2023-07 20.0 23.0 30.0 7.0 1.0

20.020 20.104

23.000 23.021 19.948 20.000

HFM-2023-16 20.0 23.0 30.0 16.5 1.5 23.000 23.021 19.948 20.000

HFM-2023-30 20.0 23.0 30.0 30.0 1.5 23.000 23.021 19.948 20.000

HFM-2528-30 25.0 28.0 35.0 30.0 1.5 25.020 25.104 28.000 28.021 24.948 25.000

HFM-2730-20 27.0 30.0 38.0 20.0 1.5 27.020 27.104 30.000 30.021 26.948 27.000

HFM-3034-40 30.0 34.0 42.0 40.0 2.0 30.020 30.104 34.000 34.025 29.948 30.000

HFM-3438-13 34.0 38.0 46.0 13.0 2.0 34.025 34.125 38.000 38.025 33.938 34.000

HFM-3539-26 35.0 39.0 47.0 26.0 2.0 35.025 35.125 39.000 39.025 34.938 35.000

HFM-4044-40 40.0 44.0 52.0 40.0 2.0 40.025 40.125 44.000 44.025 39.938 40.000

HFM-4550-50 45.0 50.0 58.0 50.0 2.0 45.025 45.125 50.000 50.025 44.938 45.000

HFM-5055-50 50.0 55.0 63.0 50.0 2.0 50.025 50.125 55.000 55.030 49.938 50.000

HFM-6065-50 60.0 65.0 73.0 50.0 2.0 60.030 60.150 65.000 65.030 59.926 60.000

HFM-7075-50 70.0 75.0 83.0 50.0 2.0 70.030 70.150 75.000 75.030 69.926 70.000