genie gs 46281.pdf

Operators Manual First EditionSeventeenth PrintingPart No. 46281with Maintenance Information

Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281

Operator's Manual First Edition Seventeenth Printing

Copyright 1997 by Genie Industries

First Edition: Seventeenth Printing, October 2002

"Genie" is a registered trademark ofGenie Industries in the U.S.A. and many othercountries. "GS" is a trademark of GenieIndustries.

These machines comply withANSI/SIA 92.6-1999.

Printed on recycled paper

Printed in U.S.A.

ImportantRead, understand and obey these safety rules andoperating instructions before operating this machine.Only trained and authorized personnel shall bepermitted to operate this machine. This manual shouldbe considered a permanent part of your machine andshould remain with the machine at all times. If you haveany questions, call Genie Industries.

ContentsPage

Safety ........................................................................ 1Legend ....................................................................... 9Controls .................................................................... 10Pre-operation Inspection ........................................... 12Maintenance ............................................................. 14Function Tests .......................................................... 16Workplace Inspection ................................................ 21Operating Instructions ............................................... 22Transport Instructions ............................................... 27Decals ...................................................................... 28Specifications ........................................................... 32

Contact us:Internet: http://www.genielift.come-mail: [email protected]

Part No. 46281 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 1

Operator's ManualFirst Edition Seventeenth Printing

Safety Rules

DangerFailure to obey the instructions andsafety rules in this manual willresult in death or serious injury.

Do Not Operate Unless:You learn and practice the principles of safemachine operation contained in this operator'smanual.

1 Avoid hazardous situations.

Know and understand the safety rulesbefore going on to the next section.2 Always perform a pre-operation inspection.3 Always perform function tests prior to use.4 Inspect the workplace.5 Only use the machine as it was intended.

You read, understand and obey:

Manufacturer's instructions and safetyrulessafety and operator's manualsand machine decals

employer's safety rules and worksiteregulationsapplicable governmental regulations

You are properly trained to safely operate themachine.

2 Genie GS-2032 & GS-2632 & GS-2046 & GS-2646 & GS-3246 Part No. 46281


SAFETY RULES

Electrocution HazardsThis machine is not electrically insulated and willnot provide protection from contact with orproximity to electrical current.

Maintain safe distances from electrical power linesand apparatus in accordance with applicablegovernmental regulations and the following chart.

Voltage Minimum SafePhase to Phase Approach Distance

Feet Meters

0 to 300V Avoid Contact

300V to 50KV 10 3.05

50KV to 200KV 15 4.60

200KV to 350KV 20 6.10

350KV to 500KV 25 7.62

500KV to 750KV 35 10.67

750KV to 1000KV 45 13.72

Allow for platform movement, electrical line swayor sag and beware of strong or gusty winds.

Keep away from the machine if it contactsenergized power lines. Personnel on the groundor in the platform must not touch or operate themachine until energized power lines are shut off.

Do not operate the machine during lightning orstorms.

Do not use the machine as a ground for welding.

Tip-over HazardsOccupants and equipment must not exceed themaximum platform capacity or the maximumcapacity of the platform extension.

Maximum capacity - GS-2032

Platform retracted 800 lbs 363 kg

Platform extended - Platform only 550 lbs 249 kgPlatform extended - Extension only 250 lbs 113 kg

Maximum occupants - ANSI and CSA 2

Maximum occupants - CE and AustraliaOutdoor use 1Indoor use only 2





Maximum occupants - CE and AustraliaIndoor use only 2

800 lbs / 363 kg Extension only250 lbs / 113 kg

Platform only550 lbs / 249 kg





SAFETY RULES

Do not raise the platform unless the machine is ona firm, level surface.

Do not depend on the tilt alarm as a level indicator.The tilt alarm sounds on the chassis only when themachine is on a slope.

If the tilt alarm sounds:Lower the platform. Move the machine to a firm,level surface. If the tilt alarm sounds when theplatform is raised, use extreme caution to lower theplatform.

Do not alter or disable the limit switches.

Do not drive over 0.5 mph / 0.7 km/h with theplatform raised.




Maximum occupants 2




Maximum occupants - CE 2

Maximum occupants - AustraliaOutdoor use 1Indoor use only 2





Maximum occupants - CE and AustraliaOutdoor use 1Indoor use only 2









GS-2046ANSI & CSA - 2 person 180 lbs / 801 NCE - Indoor use only - 2 person 180 lbs / 801 NCE - Outdoor use - 2 person 90 lbs / 400 N

GS-2646ANSI & CSA - 2 person 150 lbs / 667 NCE - Indoor use only - 2 person 150 lbs / 667 NCE - Outdoor use - 2 person 90 lbs / 400 NAustralia - Indoor use only - 2 person 120 lbs / 534 NAustralia - Outdoor use - 1 person 45 lbs / 200 N

GS-3246ANSI & CSA - 2 person 105 lbs / 467 NCE & Australia - Indoor use only - 2 person 105 lbs / 467 NCE & Australia - Outdoor use - 1 person 45 lbs / 200 N

Do not alter or disable machine components that inany way affect safety and stability.

Do not place or attach fixed or overhanging loads toany part of this machine.

Do not place ladders or scaffolds in the platform oragainst any part of this machine.

Do not modify or alter an aerial work platform.Mounting attachments for holding tools or othermaterials onto the platform, toeboards or guard railsystem can increase the weight in the platform andthe surface area of the platform or the load.

Do not operate the machine in strong or gustywinds. Do not increase the surface area of theplatform or the load. Increasing the area exposed tothe wind will decrease machine stability.

Do not drive the machine on or near uneven terrain,unstable surfaces or other hazardous conditionswith the platform raised.

Use extreme care and slow speeds while drivingthe machine in a stowed position across uneventerrain, debris, unstable or slippery surfaces andnear holes and drop-offs.

Do not push off or pulltoward any object outsideof the platform.

Maximum allowablemanual force

GS-2032ANSI & CSA - 2 person 120 lbs / 534 NCE - Indoor use only - 2 person 120 lbs / 534 NCE - Outdoor use - 1 person 45 lbs / 200 N

GS-2632ANSI & CSA - 2 person 100 lbs / 445 NCE - Indoor use only - 2 person 100 lbs / 445 NAustralia - Indoor use only - 2 person 90 lbs / 400 N

SAFETY RULES



SAFETY RULES

Do not replace items critical to machine stabilitywith items of different weight or specification.

Do not use the machine on a moving or mobilesurface or vehicle.

Be sure all tires are in good condition, castle nutsare properly tightened and cotter pins are properlyinstalled.

Do not use batteries that weigh less than theoriginal equipment. Batteries are used ascounterweight and are critical to machine stability.Each battery must weigh 65 pounds / 30 kg.

Do not use the machine as a crane.

Do not push the machine or other objects with theplatform.

Do not contact adjacent structures with theplatform.

Do not tie the platform to adjacent structures.Do not place loads outside the platform perimeter.

Do not operate the machine with the chassis traysopen.

Do not use the platform controls to free a platformthat is caught, snagged or otherwise preventedfrom normal motion by an adjacent structure. Allpersonnel must be removed from the platformbefore attempting to free the platform using theground controls.

Fall HazardsOccupants should wear asafety belt or harness andcomply with applicablegovernmental regulations.Attach the lanyard to theanchor provided in theplatform.

Do not sit, stand or climb on the platform guardrails. Maintain a firm footing on the platform floor atall times.

Do not climb down from the platform when raised.

Keep the platform floor clear of debris.

Attach the platform entry chain or close the entrygate before operating.

Do not operate the machine unless the guard railsare properly installed and the entry is secured foroperation.



SAFETY RULES

Do not lower the platform unless the area below isclear of personnel and obstructions.

Limit travel speed according to the condition of theground surface, congestion, slope, location ofpersonnel, and any other factors which may causecollision.

Do not operate a machine in the path of any craneor moving overhead machinery unless the controlsof the crane have been locked out and/orprecautions have been taken to prevent anypotential collision.

Crushing HazardsKeep hands and limbs out of scissors.

Use common sense and planning when operatingthe machine with the controller from the ground.Maintain safe distances between the operator, themachine and fixed objects.

Collision HazardsBe aware of limited sightdistance and blind spotswhen driving or operating.

Be aware of the extended platform position whenmoving the machine.

The machine must be on a level surface or securedbefore releasing the brakes.

It is recommended that operators wear an approvedhard hat when operating the machine.

Check the work area for overhead obstructions orother possible hazards.

Be aware of crushing hazards when grasping theplatform guard rail.

Observe and use the color-coded direction arrowson the platform controls and platform decal plate fordrive and steer functions.

No stunt driving or horseplay while operating amachine.



Component Damage HazardDo not use the machine as a ground for welding.

Explosion and Fire HazardDo not operate the machine in hazardous locationsor locations where potentially flammable orexplosive gases or particles may be present.

Damaged Machine HazardsDo not use a damaged or malfunctioning machine.

Conduct a thorough pre-operation inspection of themachine and test all functions before each workshift. Immediately tag and remove from service adamaged or malfunctioning machine.

Be sure all maintenance has been performed asspecified in this manual and the appropriate servicemanual.

Be sure all decals are in place and legible.

Be sure the operators, safety, and responsibilitiesmanuals are complete, legible and in the storagecontainer located on the platform.

Bodily Injury HazardDo not operate the machine with a hydraulic oil orair leak. An air leak or hydraulic leak can penetrateand/or burn skin.

Decal LegendGenie product decals use symbols, color codingand signal words to identify the following:

Safety alert symbolused to alertpersonnel to potential personalinjury hazards. Obey all safetymessages that follow this symbolto avoid possible injury or death.Redused to indicate thepresence of an imminentlyhazardous situation which, if notavoided, will result in death orserious injury.Orangeused to indicate thepresence of a potentiallyhazardous situation which, if notavoided, could result in death orserious injury.Yellow with safety alert symbolused to indicate the presence of apotentially hazardous situationwhich, if not avoided, may causeminor or moderate injury.Yellow without safety alertsymbolused to indicate thepresence of a potentiallyhazardous situation which, if notavoided, may result in propertydamage.Greenused to indicate operationor maintenance information.

SAFETY RULES



SAFETY RULES

Battery Safety

Burn HazardsBatteries contain acid. Always wear protectiveclothing and eyewear when working with batteries.

Avoid spilling or contacting battery acid. Neutralizebattery acid spills with baking soda and water.

Do not expose the batteries or the charger towater or rain during charging.

Explosion HazardsKeep sparks, flamesand lighted tobaccoaway from batteries.Batteries emit anexplosive gas.

The battery tray shouldremain open during theentire charging cycle.

Do not contact the battery terminals or the cableclamps with tools that may cause sparks.

Component Damage HazardDo not use any battery charger greater than 24V tocharge the batteries.

Electrocution HazardsConnect the battery charger to agrounded, AC 3-wire electricaloutlet only.

Inspect daily for damaged cord,cables and wires. Replacedamaged items beforeoperating.

Avoid electrical shock from contact with batteryterminals. Remove all rings, watches and otherjewelry.Tip-over HazardDo not use batteries that weigh less than theoriginal equipment. Batteries are used ascounterweight and are critical to machine stability.Each battery must weigh 65 pounds / 30 kg.

Lifting HazardUse the appropriate number of people and properlifting techniques when lifting batteries.



Legend

1 Platform entry chain or entrygate

2 Platform entry rail3 Platform guard rails4 Lanyard anchorage point5 Manual storage container6 Platform controls7 GFCI outlet8 Platform extension

9 Platform extension releasepedal

10 Tilt alarm (under cover)11 Transport tie-down12 Steer tire13 Ground controls14 Auxiliary lowering knob or

button or switch15 LED diagnostic readout16 Hydraulic oil level indicator

17 Pothole guard18 Non-steer tire19 Entry ladder/transport

tie-down20 Battery charger21 Brake release pump knob22 Brake release knob23 Safety arm

(GS-3246: safety arm locatedabove cylinder mount)



Controls

Ground Control Panel

1 Auxiliary lowering/manuallowering toggle switch orknob or button

2 Hour meter

3 5 6421

3 Red Emergency Stop button4 Breaker for electrical circuits

5 Platform up/down toggleswitch

6 Key switch for platform/off/ground selection

3 5 6421



CONTROLS

Joystick Controller1 Horn2 Machine on incline symbol: Low

speed operation for inclines3 Lift function select button with

indicator light4 Drive function select button with

indicator light5 Red Emergency Stop button6 Function enable switch7 Proportional control handle for lift

and drive functions and thumbrocker for steer function

8 Error indicator light9 Power light10 Battery level indicator11 Lift function enable button12 Lift/drive select toggle switch13 Low battery indicator light

The symbols shown below appear inthe text in this operators manual asan aid to identifying operatinginstructions.

Use the symbols on this page toidentify which controller you have onyour machine, and use the symbolsin the text to identify which action tocomplete on your controller.

If no symbol is listed for yourcontroller, then no action is needed.

Two function select buttonsand Emergency Stop buttonin upper left corner

One function select buttonand Emergency Stop buttonin upper left corner

Emergency Stop button inlower right corner



Pre-operation Inspection



2 Always perform a pre-operationinspection.

Know and understand the pre-operationinspection before going on to the nextsection.

3 Always perform function tests prior to use.4 Inspect the workplace.5 Only use the machine as it was intended.

FundamentalsIt is the responsibility of the operator to perform apre-operation inspection and routine maintenance.

The pre-operation inspection is a visual inspectionperformed by the operator prior to each work shift.The inspection is designed to discover if anythingis apparently wrong with a machine before theoperator performs the function tests.

The pre-operation inspection also serves todetermine if routine maintenance procedures arerequired. Only routine maintenance items specifiedin this manual may be performed by the operator.

Refer to the list on the next page and check eachof the items and locations for modifications,damage or loose or missing parts.

A damaged or modified machine must never beused. If damage or any variation from factorydelivered condition is discovered, the machinemust be tagged and removed from service.

Repairs to the machine may only be made by aqualified service technician, according to themanufacturer's specifications. After repairs arecompleted, the operator must perform apre-operation inspection again before going on tothe function tests.

Scheduled maintenance inspections shall beperformed by qualified service technicians,according to the manufacturer's specifications andthe requirements listed in the responsibilitiesmanual.



PRE-OPERATION INSPECTION

Pre-operation Inspection Be sure that the operator's, safety and

responsibilities manuals are complete, legibleand in the storage container located on theplatform.

Be sure that all decals are legible and in place.See Decals section.

Check for hydraulic oil leaks and proper oil level.Add oil if needed. See Maintenance section.

Check for battery fluid leaks and proper fluidlevel. Add distilled water if needed. SeeMaintenance section.

Check the following components or areas fordamage, modifications and improperly installed ormissing parts:

Electrical components, wiring and electricalcables

Hydraulic power unit, tank, hoses,fittings, cylinders and manifolds

Battery pack and connections Drive motors

Wear pads Tires and wheels

Limit switches, alarms and horn

Nuts, bolts and other fasteners

Platform entry chain (if equipped) Platform entry gate (if equipped) Beacon and alarms (if equipped) Brake release components Safety arm Pothole guards

Platform extension

Scissor pins and retaining fasteners Platform control joystick Generator (if equipped) Counterweight (if equipped)

Check entire machine for: Cracks in welds or structural components Dents or damage to machine Be sure that all structural and other critical

components are present and all associatedfasteners and pins are in place and properlytightened.

Side rails are installed and bolts are fastened Be sure that the chassis trays are in place,

latched and properly connected.



Observe and Obey:Only routine maintenance items specified in thismanual shall be performed by the operator.

Scheduled maintenance inspections shall becompleted by qualified service technicians,according to the manufacturer's specificationsand the requirements specified in theresponsibilities manual.

Maintenance Symbols Legend

The following symbols have beenused in this manual to helpcommunicate the intent of theinstructions. When one or more ofthe symbols appear at thebeginning of a maintenanceprocedure, it conveys the meaningbelow.

Indicates that tools will be required toperform this procedure.

Indicates that new parts will be required toperform this procedure.

Check the Hydraulic Oil Level

Maintaining the hydraulic oil at the proper levels isessential to machine operation. Improper hydraulicoil levels can damage hydraulic components. Dailychecks allow the inspector to identify changes in oillevel that might indicate the presence of hydraulicsystem problems.

Perform this procedure with theplatform in the stowed position.

1 Visually inspect the oil level in the hydraulictank through the sight gauge in the side of thepower unit module.Result: The hydraulic oil level should be withinthe full and add marks on the oil level indicatordecal.

2 Add oil if necessary. Do not overfill.

Hydraulic oil specifications

Hydraulic oil type Refer to machine decal

Maintenance



Check the Batteries

Proper battery condition is essential to good engineperformance and operational safety. Improper fluidlevels or damaged cables and connections canresult in engine component damage and hazardousconditions.

This procedure does not need tobe performed on machines withsealed or maintenance-freebatteries.

Electrocution hazard. Contact withhot or live circuits may result indeath or serious injury. Remove allrings, watches and other jewelry.Bodily injury hazard. Batteriescontain acid. Avoid spilling orcontacting battery acid. Neutralizebattery acid spills with baking sodaand water.

Perform this test after fullycharging the batteries.

1 Put on protective clothing and eye wear.2 Be sure that the battery cable connections are

tight and free of corrosion.3 Be sure that the battery retaining fasteners are

in place and secure.4 Remove the battery vent caps.5 Check the battery acid level of each battery. If

needed, replenish with distilled water to thebottom of the battery fill tube. Do not overfill.

6 Install the vent caps.

MAINTENANCE

Scheduled MaintenanceMaintenance performed quarterly, annually andevery two years must be completed by a persontrained and qualified to perform maintenance on thismachine according to the procedures found in theservice manual for this machine.

Machines that have been out of service for morethan three months must receive the quarterlyinspection before they are put back into service.



Function Tests



2 Always perform a pre-operation inspection.3 Always perform function tests prior to

use.

Know and understand the function testsbefore going on to the next section.4 Inspect the workplace.5 Only use the machine as it was intended.

FundamentalsThe function tests are designed to discover anymalfunctions before the machine is put into service.The operator must follow the step-by-stepinstructions to test all machine functions.

A malfunctioning machine must never be used. Ifmalfunctions are discovered, the machine must betagged and removed from service. Repairs to themachine may only be made by a qualified servicetechnician, according to the manufacturer'sspecifications.

After repairs are completed, the operator mustperform a pre-operation inspection and functiontests again before putting the machine into service.

The symbols shown below appear in the text inthis operators manual as an aid to identifyingoperating instructions.

Use the symbols on this page and page 11 toidentify which controller you have on your machine,and use the symbols in the text to identify whichaction to complete on your controller.

If no symbol is listed for your controller, then noaction is needed.

Two function select buttons andEmergency Stop button in upper leftcorner

One function select button andEmergency Stop button in upper leftcorner

Controller with Emergency Stop button inlower right corner



1 Select a test area that is firm, level and free ofobstruction.

2 Be sure the battery pack is connected.

At the Ground Controls3 Pull out the platform and ground red Emergency

Stop buttons to the on position.4 Turn the key switch to ground control.5 Observe the diagnostic LED readout.

Result: LED should read 23 or --.

Test Emergency Stop

6 Push in the ground red Emergency Stop buttonto the off position.Result: No functions should operate.

7 Pull out the red Emergency Stop button tothe on position.

Test the Up/Down Functions

The audible warnings on this machine and thestandard horn all come from the same centralalarm. The horn is a constant tone. The descentalarm sounds at 60 beeps per minute. The alarmthat goes off when the pothole guards have notdeployed sounds at 300 beeps per minute. Thealarm that goes off when the machine is not levelsounds at 600 beeps per minute. An optionalautomotive-style horn is also available.

8 Activate the up function.Result: The platform should raise.

9 Activate the down function.

Result: The platform should lower. The descentalarm should sound while the platform islowering.

Test Auxiliary Lowering/Manual Lowering

10 Activate the up function and raise the platformapproximately 2 feet / 60 cm.

11 Activate the auxiliary lowering/manual loweringfunction. Move the toggle switch OR pull theknob OR push the button.Result: The platform should lower. The descentalarm will not sound.

12 Turn the key switch to platform control.

At the Platform ControlsTest Emergency Stop

13 Push in the platform red Emergency Stop buttonto the off position.Result: No functions should operate.

Test the Horn

14 Pull the red Emergency Stop button out to theon position.

15 Push the horn button.

Result: The horn should sound.

FUNCTION TESTS



Test the Function Enable Switch

16 Do not hold the function enable switch.

17 Slowly move the control handle in the directionindicated by the blue arrow, then in the directionindicated by the yellow arrow.

Result: No functions should operate.Test the Up/Down Functions

18 Press the lift function select button.

Press and hold the lift function enablebutton.Move the lift/drive selector switch tothe lift position (if equipped).

19 Press and hold the function enable switch onthe control handle.

20 Slowly move the control handle in the directionindicated by the blue arrow.

Result: The platform should raise. The potholeguards should deploy.

21 Release the control handle.

Result: The platform should stop raising.22 Press and hold the function enable switch.

Slowly move the control handle in the directionindicated by the yellow arrow.

Result: The platform should lower. The descentalarm should sound while the platform islowering.

CE models: When lowering the platform, theplatform should stop when it is 7 feet / 2.1 m fromthe ground. Be sure the area below the platform isclear of personnel and obstructions beforecontinuing. To continue lowering, release thecontrol handle, wait 5 seconds, then move thecontrol handle again.

Test the Steering

Note: When performing the steer and drive functiontests, stand in the platform facing the steer end ofthe machine.

23 Press the drive function select switch.

Move the lift/drive selector switch tothe drive position (if equipped).


25 Depress the thumb rocker switch on top of thecontrol handle in the direction identified by theblue triangle on the control panel.Result: The steer wheels should turn in thedirection that the blue triangle points on thecontrol panel.

26 Depress the thumb rocker switch in the directionidentified by the yellow triangle on the controlpanel.Result: The steer wheels should turn in thedirection that the yellow triangle points on thecontrol panel.

FUNCTION TESTS



FUNCTION TESTS

32 Press the drive function select switch.

Move the lift/drive selector switch tothe drive position (if equipped).

33 Press and hold the function enable switch on thecontrol handle. Slowly move the control handleto the full drive position.Result: The maximum achievable drive speedwith the platform raised should not exceed0.75 feet per second / 23 cm per second.

If the drive speed with the platform raised exceeds0.75 feet per second / 23 cm per second,immediately tag and remove the machine fromservice.

Test the Tilt Sensor Operation

Note: Perform this test from the ground with theplatform controller. Do not stand in the platform.

34 Fully lower the platform.35 Place a 2x4 or similar piece of wood under both

wheels on one side and drive the machine uponto them.

36 Raise the platform approximately 7 feet / 2.1 mfrom the ground.

Machines produced before 01-01-02:

Result: The tilt alarm will sound at 600 beepsper minute.CE and Australia models: The drive function andthe lift function will not operate.Proceed to step 38.

Test Drive and Braking

27 Press and hold the function enable switch on thecontrol handle.

28 Slowly move the control handle in the directionindicated by the blue arrow on the control paneluntil the machine begins to move, then returnthe handle to the center position.Result: The machine should move in thedirection that the blue arrow points on thecontrol panel, then come to an abrupt stop.

29 Slowly move the control handle in the directionindicated by the yellow arrow on the controlpanel until the machine begins to move, thenreturn the handle to the center position.Result: The machine should move in thedirection that the yellow arrow points on thecontrol panel, then come to an abrupt stop.

Note: The brakes must be able to hold the machineon any slope it is able to climb.

Test Limited Drive Speed



31 Press and hold the function enable switch onthe control handle. Raise the platformapproximately 4 feet / 1.2 m from the ground.Result: The pothole guards should deploy.



FUNCTION TESTS

Machines produced after 12-31-01:

Result: The platform should stop and the tiltalarm will sound at 600 beeps per minute.

37 Move the drive control handle in the directionindicated by the blue arrow, then move the drivecontrol handle in the direction indicated by theyellow arrow.

Result: The drive function should not work ineither direction.

38 Lower the platform and remove both pieces ofwood.

Test the Pothole Guards

Note: The pothole guards should automaticallydeploy when the platform is raised. The potholeguards activate two limit switches which control themachine drive speed. If the pothole guards do notdeploy and the platform is raised above 6 feet /1.8 m, an alarm sounds and the machine will notdrive.

39 Raise the platform.Result: When the platform is raised 4 feet /1.2 m from the ground, the pothole guardsshould deploy.

40 Press on the pothole guards on one side, andthen the other.

Result: The pothole guards should not move.

41 Lower the platform.Result: The pothole guards should return to thestowed position.

42 Place a 2x4 or similar piece of wood under apothole guard. Raise the platform.Result: Before the platform is raised 7 feet /2.1 m from the ground, an alarm should soundand the drive function should not work.

43 Lower the platform and remove the 2x4.Test the Platform Limit Switch- GS-3246 models

Note: Some GS-3246 models are equipped with acounterweight in the chassis and do not require thistest. The counterweight is gray and measures 28inches / 71 cm by 15 inches / 38 cm. Open thechassis trays to see if your machine is equippedwith this counterweight. If not, you must performthis test.

44 Raise the platform to approximately 26 feet /7.9 m.


46 Slowly move the control handle to the full driveposition.Result: The drive function should not operate.

Lower the platform to drive.



Workplace Inspection



2 Always perform a pre-operationinspection.

3 Always perform function tests prior to use.4 Inspect the workplace.Know and understand the workplaceinspection before going on to the nextsection.

5 Only use the machine as it was intended.

FundamentalsThe workplace inspection helps the operatordetermine if the workplace is suitable for safemachine operation. It should be performed by theoperator prior to moving the machine to theworkplace.

It is the operator's responsibility to read andremember the workplace hazards, then watch forand avoid them while moving, setting up andoperating the machine.

Workplace InspectionBe aware of and avoid the following hazardoussituations:

drop-offs or holes bumps, floor obstructions or debris overhead obstructions and high voltage

conductors

hazardous locations

inadequate surface support to withstand all loadforces imposed by the machine

wind and weather conditions

the presence of unauthorized personnel other possible unsafe conditions



Operating Instructions



2 Always perform a pre-operation inspection.3 Always perform function tests prior to use.4 Inspect the workplace.5 Only use the machine as it was intended.

FundamentalsThe Operating Instructions section providesinstructions for each aspect of machine operation.It is the operator's responsibility to follow all thesafety rules and instructions in the operator's,safety and responsibilities manuals.

Using the machine for anything other than liftingpersonnel and tools to an aerial work site is unsafeand dangerous.

Only trained and authorized personnel should bepermitted to operate a machine. If more than oneoperator is expected to use a machine at differenttimes in the same work shift, they must all bequalified operators and are all expected to follow allsafety rules and instructions in the operator's,safety and responsibilities manuals. That meansevery new operator should perform a pre-operationinspection, function tests, and a workplaceinspection before using the machine.



OPERATING INSTRUCTIONS

To Position Platform




3 Move the control handle according to themarkings on the control panel.

CE models: When lowering the platform, theplatform should stop when it is 7 feet / 2.1 m fromthe ground. Be sure the area below the platform isclear of personnel and obstructions beforecontinuing. To continue lowering, release thecontrol handle, wait 5 seconds, then move thecontrol handle again.

To Steer

1 Press the drive function select button.

Move the lift/drive selector switch tothe drive position.


3 Turn the steer wheels with the thumb rockerswitch located on the top of the control handle.

Emergency StopPush in the red Emergency Stop button to the offposition at the ground controls or the platformcontrols to stop all functions.

Repair any function that operates when either redEmergency Stop button is pushed in.

Auxiliary Lowering/ManualLowering1 Activate the auxiliary lowering/manual lowering

function. Move the toggle switch OR pull theknob OR push the button.

Operation From Ground1 Turn the key switch to ground control.2 Pull out both ground and platform red

Emergency Stop buttons to the on position.3 Be sure the battery pack is connected before

operating the machine.To Position Platform

1 Move the up/down toggle switch according tothe markings on the control panel.

Drive and steer functions are not available fromthe ground controls.

Operation From Platform1 Turn the key switch to platform control.2 Pull out the ground and platform red Emergency

Stop buttons to the on position.3 Be sure the battery pack is connected before

operating the machine.



Error Indicator Light On

If the error indicator light is on,push in and pull out the redEmergency Stop button to resetthe system.

If the light stays on, tag and remove the machinefrom service.

Drive Select Switch

Machine on incline symbol:Low range operation for inclines

Move the toggle switch down for normal driveoperation.


To Drive

1 Press the drive function select button.

Move the lift/drive selector switch tothe drive position.


3 Increase speed: Slowly move the controlhandle off center.

Decrease speed: Slowly move the controlhandle toward center.

Stop: Return the control handle to center orrelease the function enable switch.

Use the color-coded direction arrows on theplatform controls and on the platform to identifythe direction the machine will travel.

Machine travel speed is restricted when theplatform is raised.

Battery condition will affect machine performance.Machine drive speed and function speed will dropwhen the low battery indicator light is on or whenthe last light on the battery level indicator isflashing.



To Extend and Retract Platform1 Step on the platform extension release pedal on

the platform toeboard.2 Grasp the platform guard rails and carefully push

to extend the platform to the mid-position stop.3 Step on the release pedal again and push to

fully extend the platform.Do not stand on the platform extension while tryingto extend it.

4 Step on the platform extension release pedaland pull to retract the platform to the mid-position stop. Step again to fully retract theplatform.

GS-3246 models without chassis counterweight:The platform extension limit switch will disable thedrive function when the platform is extended andthe platform is raised above 26 ft / 7.9 m. Lower theplatform or retract the platform extension to drivethe machine.

Operation From Ground withControllerMaintain safe distances between the operator,machine and fixed objects.Be aware of the direction the machine will travelwhen using the controller.

After Each Use1 Select a safe parking locationfirm level

surface, clear of obstruction and traffic.

2 Lower the platform.3 Turn the key switch to the off position and

remove the key to secure from unauthorizeduse.

4 Chock the wheels.5 Charge the batteries.




Battery and Charger Instructions

Observe and Obey:Do not use an external charger or boosterbattery.

Charge the battery in a well-ventilated area.

Use proper AC input voltage for charging asindicated on the charger.

Use only Genie authorized battery and charger.

To Charge Battery1 Be sure the batteries are connected before

charging the batteries.2 Open the battery compartment. The

compartment should remain open for the entirecharging cycle.

3 Remove the battery vent caps and check thebattery acid level. If necessary, add onlyenough distilled water to cover the plates. Donot overfill prior to the charge cycle.

4 Replace the battery vent caps.5 Connect the battery charger to a grounded AC

circuit.

6 Turn the battery charger on.7 The charger will indicate when the battery is

fully charged.8 Check the battery acid level when the charging

cycle is complete. Replenish with distilled waterto the bottom of the fill tube. Do not overfill.

Dry Battery Filling andCharging Instructions1 Remove the battery vent caps and permanently

remove the plastic seal from the battery ventopenings.

2 Fill each cell with battery acid (electrolyte) untilthe level is sufficient to cover the plates.

Do not fill to maximum level until the batterycharge cycle is complete. Overfilling can cause thebattery acid to overflow during charging.Neutralize battery acid spills with baking soda andwater.

3 Install the battery vent caps.4 Charge the battery.5 Check the battery acid level when the charging

cycle is complete. Replenish with distilled waterto the bottom of the fill tube. Do not overfill.




Transport Instructions

Observe and Obey:Common sense and planning must be applied tocontrol the movement of the machine whenlifting it with a crane or forklift.

The transport vehicle must be parked on a levelsurface.

The transport vehicle must be secured toprevent rolling while the machine is beingloaded.

Be sure the vehicle capacity, loading surfacesand chains or straps are sufficient to withstandthe machine weight. See the serial plate for themachine weight.

The machine must be on a level surface orsecured before releasing the brakes.

Securing to Truck or Trailer forTransitAlways chock the machine wheels in preparationfor transport.

Use the tie-down points on the chassis foranchoring down to the transport surface.

Use chains or straps of ample load capacity.

Turn the key switch to the off position and removethe key before transporting.

Inspect the entire machine for loose or unsecureditems.

Brake Release Operation1 Chock the wheels to prevent the machine from

rolling.2 Be sure the winch line is properly secured to the

drive chassis tie points and the path is clear ofall obstructions.

3 Turn the brake release knob counterclockwiseto open the brake valve.

4 Pump the brake release pump knob.After the machine is loaded:

1 Chock the wheels to prevent the machine fromrolling.

2 Turn the brake release knob clockwise to resetthe brakes.

Towing the Genie GS-2032, the GS-2632, theGS-2046, the GS-2646 or the GS-3246 is notrecommended. If the machine must be towed, donot exceed 2 mph / 3.2 km/h.



Decals

Part No. Description Quantity28161 Warning - Crush Hand 228164 Notice - Hazardous Materials 128171 Label - No Smoking 128174 Label - Power to Platform, 230V 228175 Caution - Compartment Access 128176 Notice - Missing Manuals 128235 Label - Power to Platform, 115V 228236 Warning - Failure To Read . . . 131060 Danger - Do Not Alter Limit Switch 231508 Notice - Power to Battery Charger 131785 Notice - Battery Charger Operating

Instructions 137145 Label - Manual Lowering 138149 Label - Patents 140434 Label - Lanyard Anchorage 543089 Notice - Operating Instructions, Ground 143090 Notice - Operating Instructions, Platform 143091 Danger - General Safety Rules 143094 Ground Control Panel 143617 Danger - Tip-over (batteries) 143618 Label - Directional Arrows 243619 Label - Safety Arm 143658 Label - Power to Charger, 230V 143696 Danger - Electrocution Hazard 244220 Danger/Notice - Brake Release Safety &

Operating Instructions 144254 Notice - Max Cap 500 lbs, GS-2632 144255 Danger - Crushing Hazard 444736 Danger - Tilt Alarm 144737 Danger - Tip-over, Trays Open 244753 Label - LED Diagnostic Readout 144980 Label - Power to Charger, 115V 144994 Label - Hydraulic Fluid Level / Dexron 1

Decal InspectionUse the pictures on the next pages to verify that alldecals are legible and in place.Below is a numerical list with quantities anddescriptions.

Part No. Description Quantity46238 Notice - Error Indicator Light 146262 Danger - Battery/Charger Safety 146285 Notice - Max Cap 800 lbs, GS-2032,

ANSI & CSA 146286 Notice - Battery Connection Diagram 146287 Notice - Tire Specification 452063 Notice - Max Cap 800 lbs, GS-2032, CE 152475 Label - Transport Tie-down 552494 Caution - Crushing Hazard 152560 Notice - Side Force & Wind Speed,

GS-2032, CE 152608 Notice - Side Force,GS-2032, ANSI & CSA 152864 Platform Control Panel 162055 Cosmetic - Genie GS-2032 265052 Label - ECU Fault Codes 172833 Label - Open Latches 272853 Danger - Improper Use Hazard 172973 Cosmetic - Genie GS-2632 272990 Notice - Side Force & Wind Speed,

GS-2632, CE 172992 Notice - Side Force, GS-2632,

ANSI & CSA 182307 Notice - Side Force, GS-2632,

Australia 182368 Label - Chevron Rykon 182448 Ground Control Panel 1



DECALS

Battery Side

GroundControls Side



Part No. Description Quantity28161 Warning - Crush Hand 228164 Notice - Hazardous Materials 128171 Label - No Smoking 128174 Label - Power to Platform, 230V 228175 Caution - Compartment Access 128176 Notice - Missing Manuals 128235 Label - Power to Platform, 115V 228236 Warning - Failure To Read . . . 131060 Danger - Do Not Alter Limit Switch 231508 Notice - Power to Battery Charger 131785 Notice - Battery Charger Operating

Instructions 137145 Label - Manual Lowering 138149 Label - Patents 140434 Label - Lanyard Anchorage 543089 Notice - Operating Instructions, Ground 143090 Notice - Operating Instructions, Platform 143091 Danger - General Safety Rules 143094 Ground Control Panel 143617 Danger - Tip-over (batteries) 143618 Label - Directional Arrows 243619 Label - Safety Arm 143658 Label - Power to Charger, 230V 143696 Danger - Electrocution Hazard 244220 Danger/Notice - Brake Release Safety &

Operating Instructions 144254 Notice - Max Cap 500/250, GS-3246, CSA 144255 Danger - Crushing Hazard 444736 Danger - Tilt Alarm 144737 Danger - Tip-over, Trays Open 244753 Label - LED Diagnostic Readout 144980 Label - Power to Charger, 115V 144994 Label - Hydraulic Fluid Level / Dexron 1

Decal InspectionUse the pictures on the next pages to verify that alldecals are legible and in place.Below is a numerical list with quantities anddescriptions.

Part No. Description Quantity46238 Notice - Error Indicator Light 146262 Danger - Battery/Charger Safety 146286 Notice - Battery Connection Diagram 146287 Notice - Tire Specification 448331 Notice - Max Cap 1000 lbs, GS-2646 152084 Notice - Max Cap 1200 lbs, GS-2046 152337 Notice - Max Cap 700 lbs, GS-3246 152475 Label, Transport Tie-down 552494 Caution, Crushing Hazard 152561 Notice - Side Force & Wind Speed,

GS-2046, CE 152562 Notice - Side Force & Wind Speed,

GS-2646, CE 152563 Notice - Side Force & Wind Speed,

GS-3246, CE 152609 Notice - Side Force,GS-2046,

ANSI & CSA 152610 Notice - Side Force,GS-2646,

ANSI & CSA 152864 Platform Control Panel 162056 Cosmetic - Genie GS-2046 262057 Cosmetic - Genie GS-2646 262058 Cosmetic - Genie GS-3246 265052 Label - ECU Fault Codes 172084 Notice - Side Force & Wind Speed,

GS-3246, CE 172120 Notice - Max Side Force, ANSI & CSA 178026 Notice - Side Force, GS-2646, Australia 178027 Notice - Max. Capacity, GS-2646, Australia 178028 Notice - Max. Capacity, GS-3246, CE

and Australia 172833 Label - Open Latches 272853 Danger - Improper Use Hazard 182368 Label - Chevron Rykon 182447 Label - Auxiliary Lowering 182448 Ground Control Panel 1

DECALS



DECALS

Battery Side

GroundControls Side



Specifications

Model GS-2032

Height, working maximum 26 ft 8.1 m

Height, platform maximum 20 ft 6.1 m

Height, stowed maximum 827/8 in 2.1 mRails up - CE

Height, stowed maximum 781/2 in 1.99 mRails up - ANSI

Height, stowed maximum 761/2 in 1.94 mRails lowered

Height, stowed maximum 39 in 99 cmRails off

Height, guard rails - 39 in 99 cmANSI, CSA and Australia

Height, guard rails - CE 431/2 in 1.1 m

Width 32 in 81.3 cm

Length, stowed 96 in 2.44 m

Length, platform extended 135 in 3.44 m

Maximum load capacity 800 lbs 363 kg

Wheelbase 73 in 1.85 m

Turning radius (outside) 92 in 2.34 mTurning radius (inside) 0 in 0 cmGround clearance 4.0 in 10.2 cm

Ground clearance 7/8 in 2.2 cmPothole guards deployed

Weight See Serial Plate(Machine weights vary with option configurations)Gradeability 30%

Airborne noise emissions 70 dBMaximum sound level at normal operating workstations(A-weighted)Power source 4 Batteries, 6V 245AH

Controls Proportional

Continuous improvement of our products is a Genie policy.Product specifications are subject to change without notice or obligation.

AC outlet in platform standard

Maximum hydraulic pressure(functions) 3500 psi 241.3 barTires size 15 x 5 x 111/4

Hydraulic system capacity 5.5 gallons20.8 liters

Platform dimensions

Length x width 89 in x 311/4 in2.26 m x 79.4 cm

Platform extension length 39 in99 cm

Drive speeds

Stowed, maximum 2.2 mph3.5 km/h

Platform raised, maximum 0.5 mph0.8 km/h

40 ft/54.5 sec12.2 m/54.5 sec

Floor Loading ANSIInformation CSA & CE Australia

GVW+Rated Load 4303 lbs 5306 lbs1952 kg 2407 kg

Axle load, maximum 2450 lbs 3410 lbs1111 kg 1547 kg

Wheel load, maximum 1225 lbs 1705 lbs555 kg 773 kg

Localized pressure per tire 123 psi 170.5 psi8.62 kg/cm2 12.0 kg/cm2

845 kPa 1176 kPa

Occupied pressure 218 psf 268 psf10.42 kPa 12.85 kPa

Note: Floor loading information is approximate anddoes not incorporate different option configurations.It should be used only with adequate safety factors.



SPECIFICATIONS

Model GS-2632



Height, stowed maximum 90 in 2.29 m

Height, stowed maximum 68 in 1.73 mRails folded

Platform height, 461/8 in 1.17 mStowed maximum

Height, guard rails - 39 in 99.1 cmANSI, CSA and Australia

Height, guard rails - CE 43 in 1.1 m

Width 32 in 81.3 cm





Turning radius (outside) 92 in 2.34 mTurning radius (inside) 0 in 0 cmGround clearance 4.0 in 10.2 cm


Weight See Serial Plate(Machine weights vary with option configurations)Gradeability 25%



Continuous improvement of our products is a Genie policy.Product specifications are subject to change without notice or obligation.


Maximum hydraulic pressure(functions) 3500 psi 241.3 barTires size 15 x 5 x 111/4

Platform dimensions

Length x width 89 in x 311/4 in2.26 m x 79.4 cm

Platform extension length 39 in99 cm

Drive speeds



40 ft/54.5 sec12.2 m/54.5 sec

Floor Loading Information ANSI CECSA Australia




Localized pressure per tire 181.5 psi 186.9 psi12.77 kg/cm2 13.15 kg/cm2

1251 kPa 1289 kPa





Model GS-2046



Models with sliding rails




Height, stowed maximum 391/4 in 99.7 cmRails off



Models with folding rails

Height, stowed maximum 861/8 in 2.19 m

Height, stowed maximum 643/8 in 1.64 mRails folded


All models

Width 46 in 1.17 m





Turning radius (outside) 92 in 2.34 mTurning radius (inside) 0 in 0 cmGround clearance 4 in 10.2 cm


Weight See Serial Plate(Machine weights vary with option configurations)

Gradeability 30 %




Maximum hydraulic pressure 3500 psi 241 bar(functions)Tires size 15 x 5 x 111/4

Hydraulic system capacity 51/2 gallons 20.8 liters

Platform dimensions

Length x width 89 x 453/4 in2.26 m x 1.16m

Platform extension length 39 in 99 cm

Drive speeds



40 ft/54.5 sec12.2 m/54.5 sec

Floor Loading Information

GVW+Rated Load 5524 lbs 2506 kg

Axle load, maximum 2900 lbs 1315 kg

Wheel load, maximum 1450 lbs 657 kg

Localized pressure per tire 145 psi 10.2 kg/cm21000 kPa

Occupied pressure 194 psf 9.30 kPa


SPECIFICATIONS



SPECIFICATIONS

Model GS-2646







Height, stowed maximum 461/8 in 1.17 mRails off




Height, stowed maximum 897/8 in 2.28 m



All models

Width 46 in 1.17 m








Gradeability 30%

Airborne noise emissions >70 dBMaximum sound level at normal operating workstations(A-weighted)Power source 4 Batteries, 6V 245AH



Maximum hydraulic pressure 3500 psi 241.3 bar(functions)Tires size 15 x 5 x 111/4

Hydraulic system capacity 5.5 gallons 20.8 liters

Platform dimensions

Length x width 89 x 453/4 in2.26 m x 1.16 m


Drive speeds

Stowed, maximum 2.2 mph 3.5 km/h


40 ft/54.5 sec12.2 m/54.5 sec

Floor Loading Information ANSI CECSA & Australia




Localized pressure per tire 155 psi 186.3 psi10.91 kg/cm2 13.11 kg/cm2

1069 kPa 1284 kPa





SPECIFICATIONS

Model GS-3246




Height, stowed maximum 95 in 2.41 mRails up - CE



Height, stowed maximum 511/4 in 1.3 mRails off


Height, guard rails - CE 431/2 in 1.1 m


Height, stowed maximum 95 in 2.41 m



All models

Width 46 in 1.17 m








Gradeability 25%

Airborne noise emissions >70 dBMaximum sound level at normal operating workstations(A-weighted)Power source 4 Batteries, 6V 245AH



Maximum hydraulic pressure 3500 psi 241.3 bar(functions)Tires size 15 x 5 x 111/4

Hydraulic system capacity 5.5 gallons 20.8 liters

Platform dimensions

Length x width 89 x 453/4 in2.26 m x 1.16 m


Drive speeds



40 ft/54.5 sec12.2 m/54.5 sec

Floor Loading Information

GVW+Rated Load 6872 lbs 3117 kg

Axle load, maximum 4040 lbs 1833 kg

Wheel load, maximum 2020 lbs 916 kg

Localized pressure per tire 202 psi 14.21 kg/cm21393 kPa

Occupied pressure 242 psf 11.57 kPa


Genie North America

Genie Australia Pty Ltd.

Genie China

Genie Malaysia

Genie Japan

Genie Korea

Genie Africa

Genie Latin America

Phone

Toll Free

Fax

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

425.881.1800

USA and Canada

800.536.1800

425.883.3475

61 7 3375 1660

61 7 3375 1002

86 21 53852570

86 21 53852569

60 4 228 1235

60 4 226 6872

81 3 3453 6082

81 3 3453 6083

82 2 558 7267

82 2 558 3910

27 11 455 0373

27 11 455 0355

55 11 4055 2499

55 11 4043 1661

Genie Holland

Genie Scandinavia

Genie France

Genie Iberica

Genie Germany

Genie U.K.

Genie Mexico City

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

Phone +

Fax +

31 70 51 78836

31 70 51 13993

46 31 3409612

33 (0)2 37 26 09 99

33 (0)2 37 26 09 98

34 93 579 5042

34 93 579 5059

49 (0)4202 88520

49 (0)4202 8852-20

44 (0)1476 584333

44 (0)1476 584334

52 55 5666 5242

52 55 5666 3241

46 31 3409613

Dis

trib

ute

dB

y:

genie gs 46281.pdf

Documents