G-Code/E2 Series

1

Quick Start Guide G-Code/EEN-2040

This manual has been designed to guide you through basic settings of your IP devices, such as installation and configuration for using them.

1. Connect cables to IP device

Connect each cable to the device. To see the correct positions of all connectors, refer to the following image below.

Make sure to set the input configuration switch to a relevant video standard position (PAL/NTSC) before you turn on the encoder. The device must be rebooted to apply the changed video standard after you change the position of the switch.

Video In

OFF

PAL NTSCInput Configuration Switch (PAL/NTSC)

* Models herein and their appearance are subject to change without any prior notice.

Power DC 12V

Network Port

G-Code/E2 Series

2

2. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the device from converting the MAC address’s hexadecimal numbers, which is attached to the device. Be sure that the device and PC are on a same area network before running the installation. If the network segment was different between your PC and the device, change your PC’s settings as below. IP address : 192.168.xxx.xxx Subnet mask: 255.255.0.0

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are used, users may view the live streaming images on a web page using the device’s default IP address: Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal Conversion Chart at the end of the manual. (The MAC address of the device is attached on the side or bottom of the device.)

Start the Microsoft® Internet Explorer web browser and enter the IP address of the device.

Web streaming and device configurations are supported through ActiveX program. When the ActiveX installation pop-up window appears, authorize and install the ActiveX setup.exe.

MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177

Convert the last two set of hexadecimal numbers to decimal numbers.

G-Code/E2 Series

3

Custom IP Environment

IPAdminTool is a management tool, which automatically scans all of the network products for users to perform administrative tasks, which includes network configurations, firmware update, device reboot, and device organizations.

To modify the device’s default IP address for customized network area; Find the device from the IPAdminTool’s list and highlight the device’s name. Right-click the mouse and select IP Address; IP Setup window appears.

In the IP Setup’s window, information under Local Network information displays the user/PC’s network area information. Those information need to be incorporated to the IP Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address, which are to be the unique numbers for the device. Refer to the image above for the setting Click Setup to complete the modification. Enter the user name and the password, and then select Login. (The default username and password are: root and admin.)

G-Code/E2 Series

4

3. View video on web page

Once the device’s proper IP address has been identified, type the URL in a web browser to access the camera. At first time access, installation window may pop up.

When the browser asks to install the AxUMF software, click Install to proceed.

When Setup installation pop-up window appears, click Install to proceed with rest of installations.

Depending on system OS and Internet Explorer version, installation experience may differ from one another. Figures described above are from Windows 7, Internet Explorer 9 environment.

4. SETUP page

To set up the device configuration: Click Setup on the upper left of the web page. The login page will be displayed. Enter the user name and the password, and then select OK. (The default username and password are: root and admin.)

5. Reboot

Perform the following procedures to reset your device: While the device is in use, press the Reset button. Wait for the system to reboot.

Please do not hold for more than 2 seconds. Otherwise, the camera may be switched to its Factory Default settings.

G-Code/E2 Series

5

6. Factory Default

If you reset your device to the factory default setting, all parameters including the IP address will be initialized. For the Factory Default reset: 1. Press reset button and hold while the device is in use. 2. Release the Reset button after 10 seconds until LED blinks. 3. Wait for the system to reboot.

The factory default settings can be inferred as follows: IP address: 192.168.xx.yy Network mask: 255.255.0.0 Gateway: 192.168.0.1 User ID: root Password: admin

G-Code/E2 Series

6

7. Safe Mode Your device will get restarted in safe mode if the device does not completely boot certain

times. The errors are mainly caused by these factors below:

* The power supply is continually unplugged certain times in the middle of system booting. * The firmware files required for system booting are damaged. * There are conflicts in the system settings.

You will see the page to indicate that your device is in safe mode and to guide you what to do in steps. Follow the instructions on the webpage according to each step.

There is another method to update firmware, which is using IPAdminTool.

Please refer to ‘IPAdminTool User’s Manual.pdf’ for the detailed procedure.

If your device is still in safe mode after trying to update firmware, please contact your local agency to get further assistance.

The format of firmware file for safe mode itself is ‘ipn-SAFEMODE.~~~.enc’.

Browse

G-Code/E2 Series

7

Hexadecimal-Decimal Conversion Table

Refer to the following table when you convert the MAC address of your device to IP address. Hex Dec

00 0 01 1 02 2 03 3 04 4 05 5 06 6 07 7 08 8 09 9 0A 10 0B 11 0C 12 0D 13 0E 14 0F 15 10 16 11 17 12 18 13 19 14 20 15 21 16 22 17 23 18 24 19 25 1A 26 1B 27 1C 28 1D 29 1E 30 1F 31

Hex Dec20 3221 3322 3423 3524 3625 3726 3827 3928 4029 412A 422B 432C 442D 452E 462F 4730 4831 4932 5033 5134 5235 5336 5437 5538 5639 573A 583B 593C 603D 613E 623F 63

Hex Dec40 6441 6542 6643 6744 6845 6946 7047 7148 7249 734A 744B 754C 764D 774E 784F 7950 8051 8152 8253 8354 8455 8556 8657 8758 8859 895A 905B 915C 925D 935E 945F 95

Hex Dec60 9661 9762 9863 9964 10065 10166 10267 10368 10469 1056A 1066B 1076C 1086D 1096E 1106F 11170 11271 11372 11473 11574 11675 11776 11877 11978 12079 1217A 1227B 1237C 1247D 1257E 1267F 127

G-Code/E2 Series

8

Hex Dec 80 128 81 129 82 130 83 131 84 132 85 133 86 134 87 135 88 136 89 137 8A 138 8B 139 8C 140 8D 141 8E 142 8F 143 90 144 91 145 92 146 93 147 94 148 95 149 96 150 97 151 98 152 99 153 9A 154 9B 155 9C 156 9D 157 9E 158 9F 159

Hex DecA0 160A1 161A2 162A3 163A4 164A5 165A6 166A7 167A8 168A9 169AA 170AB 171AC 172AD 173AE 174AF 175B0 176B1 177B2 178B3 179B4 180B5 181B6 182B7 183B8 184B9 185BA 186BB 187BC 188BD 189BE 190BF 191

Hex DecC0 192C1 193C2 194C3 195C4 196C5 197C6 198C7 199C8 200C9 201CA 202CB 203CC 204CD 205CE 206CF 207D0 208D1 209D2 210D3 211D4 212D5 213D6 214D7 215D8 216D9 217DA 218DB 219DC 220DD 221DE 222DF 223

Hex DecE0 224E1 225E2 226E3 227E4 228E5 229E6 230E7 231E8 232E9 233EA 234EB 235EC 236ED 237EE 238EF 239F0 240F1 241F2 242F3 243F4 244F5 245F6 246F7 247F8 248F9 249FA 250FB 251FC 252FD 253FE 254FF 255