flat spray sprinkler

7/30/2019 Flat Spray Sprinkler

1/10

GeneralDescriptionThe Model TY-FRFS, TY-FS Special,and TY-FS, Upright and Pendent, Flat

Spray Sprinklers described in this datasheet are intended for installation inaccordance with CEA 4001 SprinklerSystems Planning and Installation orEN12845 Automatic Sprinkler Sys-tems - Design, Installation and Mainte-nance, as applicable. They produce aflatter spray pattern than standardspray sprinklers enabling them to beused with lower clearance above thesuspended open ceilings and in racks.

As necessary the 80K and 115K, FlatSpray Sprinklers may be outfitted withguards, shie lds, or guards wi thshields. The guards may be used inareas that make thesprinklers suscep-tible to mechanical or physical dam-age, whereas the shields may be usedto help prevent the sprinklers from be-ing wetted (cold soldered) from waterspray of higher elevation sprinklers.Table A provides a detailed matrix ofthe allowable combinations.

The Model TY-FRFS with its 3 mmdiameter heat sensitive bulb elementis rated quick response, the Model TY-FS Special with its 4 mm diameter heatsensitive bulb element is rated specialresponse, and the Model TY-FS withits 5 mm diameter heat sensitive bulb

element is rated standard responseA.

CEA 4001 Sprinkler Systems Plan-ning and Installation and EN12845Automatic Sprinkler Systems - De-sign, Installation and Maintenance

permits flat spray sprinklers to be usedin concealed spaces, suspended openceilings, and in racks.

WARNINGSModel TY-FRFS, TY-FS Special, andT Y- FS S pr in kl er s, a s w el l a s guard/shield accessories, describedherein must be installed and main-tained in compliance with this docu-ment, as well as with the applicablestandards recognized by the Approvalagency, in addition to the standards ofany other authorities having jurisdic-tion. Failure to do so may impair theperformance of these devices.

The owner is responsible for maintain-ing their fire protection system and de-vices in proper operating condition.The installing contractor or sprinklermanufacturer should be contactedwith any questions.

Model TY-FRFS

Model TY-FS Special

Model TY-FS

Model TY-FRFS, TY-FS Special, and TY-FSFlat Spray Sprinkle rs, Guards, a nd ShieldsUpright a nd Pendent 57 , 80 , and 1 15 K-factor

Pa ge 1 of 1 0 T FP6 3 5M A Y , 2 0 0 6

Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500

IMPORTANTAlways refer t o Technical DataSheet TFP700 for the INSTALLERWARNING that provides cautionswith respect to handling and instal-lation of sprinkler systems and com-ponents. Improper handling and in-stallation can permanently damagea sprinkler system or its compo-nents and cause the sprinkler to failto operate in a fire situation or causeit to operate prematurely.


2/10

Model/SprinklerIdentificationNumbersModel FRFS (3 mm Bulb)TY1136 - Upright 57KTY1236 - Pendent 57KTY3136 - Upright 80KTY3236 - Pendent 80KTY4136 - Upright 115K

TY4236- Pendent 115KModel FS Special (4 mm Bulb)TY1146 - Upright 57KTY1246 - Pendent 57KTY3146 - Upright 80KTY3246 - Pendent 80KTY4146 - Upright 115KTY4246- Pendent 115K

Model FS (5 mm Bulb)TY1156 - Upright 57KTY1256 - Pendent 57KTY3156 - Upright 80KTY3256 - Pendent 80KTY4156 - Upright 115KTY4256- Pendent 115K

OperationThe glass bulb contains a fluid whichexpands when exposed to heat. Whenthe rated temperature is reached, thefluid expands sufficiently to shatter theglass bulb, allowing the sprinkler toactivate and water to flow.

Technical DataApprovalsThe Flat Spay Sprinklers are VdS Ap-proved for installation per CEA 4001Sprinkler Systems Planning and In-stallation or EN12845 AutomaticSprinkler Systems - Design, Installa-tion and Maintenance.

The Guards, Shields, and Guards withShields are VdS Approved with thecombinations of product shown in Ta-ble A.

For details contact Tyco Fire & Build-ing Products, Enschede, Netherlands:Tel. 31-53-428-4444Fax 31-53-428-3377

Maximum Working Pressure12,1 bar

Discharge CoefficientK = 57 LPM/bar1/2

K = 80 LPM/bar1/2

K = 115 LPM/bar1/2

Temperature Ratings in C57, 68, 79, 93, and 141

FinishesSprinklers: Natural BrassGuards: Red Painted / Zinc ChromateShields: Zinc Chromate

Physical CharacteristicsFrame . . . . . . . . . . . . . BronzeButton . . . . . . . . . . . . CopperSealing Assembly . . . . . . . . . . .. . . . . . Beryllium Nickel w/Teflon*

Bulb . . . . . . . . . . . . . . GlassCompression Screw . . . . . BronzeDeflector . . . . . . . . . . . Copper

Guard . . . . Welded Carbon steelShield . . . . . . . . . Carbon SteelShield Spring . . . . . Carbon Steel

* Registered trademark of DuPont

DesignCriteriaThe Model TY-FRFS, TY-FS Special,

and TY-FS Flat Spray Sprinklers areonly intended for installation per CEA4001 Sprinkler Systems Planning andInstallation or EN12845 AutomaticSprinkler Systems - Design, Installa-t ion and Maintenance where flatspray sprinklers are permitted.

NOTEIn all cases, CEA 4001 Sprinkler Sys-tems Planning and Installation orEN12845 Automatic Sprinkler Sys-tems - Design, Installation and Mainte-nance must be referenced and fol-l ow ed t o e ns ur e a n e ffe ct iv e installation. The Flat Spay Sprinklers

have significantly different water distri-bution characteristics from that of con-ventional and spray pattern sprinklersthat has enabled the Flat Spray Sprin-klers to be used in conformance withCEA 4001 Sprinkler Systems Plan-ning and Installation or EN12845Automatic Sprinkler Systems - De-sign, Installation and Maintenance.

P a g e 2 o f 1 0 TFP6 3 5

TABLE A

ALLOWABLE COMBINATIONS OF GUARDS, SHIELDS, AND GUARDS WITH SHIELDS

Series Bulb Size Orifice Position SIN Guard Shield Guard/Shield

TY-FRFS 3 mm TY1136 N/A N/A N/A

TY-FS Special 4 mm TY1146 N/A N/A N/A

TY-FS 5 mm TY1156 N/A N/A N/A

TY-FRFS 3 mm TY1236 N/A N/A N/A

TY-FS Special 4 mm TY1246 N/A N/A N/A

TY-FS 5 mm TY1256 N/A N/A N/ATY-FRFS 3 mm TY3136 G1 N/A N/A

TY-FS Special 4 mm TY3146 G1 N/A N/A

TY-FS 5 mm TY3156 G1 N/A N/A

TY-FRFS 3 mm TY3236 G1 H1or H2 G1/H1 or G1/H2

TY-FS Special 4 mm TY3246 G1 H1or H2 G1/H1 or G1/H2

TY-FS 5 mm TY3256 G1 H1or H2 G1/H1 or G1/H2

TY-FRFS 3 mm TY4136 G1 N/A N/A

TY-FS Special 4 mm TY4146 G1 N/A N/A

TY-FS 5 mm TY4156 G1 N/A N/A

TY-FRFS 3 mm TY4236 G1 H1 or H2 G1/H1 or G1/H2

TY-FS Special 4 mm TY4246 G1 H1 or H2 G1/H1 or G1/H2

TY-FS 5 mm TY4256 G1 H1 or H2 G1/H1 or G1/H2

115K, 20 mm

Upright

Pendent

Pendent

57K, 10 mm

80K, 15 mm

Upright

Upright

Pendent


3/10

TFP6 3 5 P a g e 3 o f 1 0

FIGURE 1

57 K-FACTOR, ISO 7/1-R 3/8UPRIGHT AND PENDENT FLAT SPRAY SPRINKLERS

FIGURE 280 K-FACTOR, 1/2 INCH NPT

UPRIGHT AND PENDENT FLAT SPRAY SPRINKLERS

Components:

55 mm

MAKE-INNOMINAL

10 mm

WRENCHFLATS

UPRIGHT

MAKE-INNOMINAL

PENDENT

40 mm

55 mm

10 mm

*CROSS SECTION

2

6

45

3

1

*

Frame

Button

Bulb (See table above)Compression Screw

Deflector

Sealing Assembly--

-

--

- *2

1

3

5

4

6

Temperature rating is indicated onDeflector or adjacent to orifice seat

*

on frame.

*DEFLECTOR

DEFLECTOR

BULB

SIZEMODEL

SIN

UPRIGHT

TY11363 mmTY-FRFS

TY-FS SPECIAL 4 mm TY1146

TY-FS 5 mm TY1156

PENDENT

TY1236

TY1256

TY1246

7/1-R 3/8

ISO

7/1-R 3/8

ISO

Components:

57 mm

MAKE-INNOMINAL

11 mm

WRENCHFLATS

UPRIGHT

MAKE-INNOMINAL

PENDENT

40 mm

57 mm

11 mm

*CROSS SECTION

2

6

45

3

1

*

Frame

Button

Bulb (See table above)Compression ScrewDeflector

Sealing Assembly-

-

---

-

*

2

1

3

5

4

6

THREADRELIEF


*can be provided on special request.Pipe thread connections per ISO 7/1**

on frame.

*DEFLECTORPLATE SEATINGESCUTCHEON

SURFACE

SHIELD AND

1/2" NPT

DEFLECTOR1/2" NPT **

**

BULB

SIZEMODEL

SIN

UPRIGHT

TY31363 mmTY-FRFS


TY-FS 5 mm TY3156

PENDENT

TY3256

TY3246

TY3236


4/10

P a g e 4 o f 1 0 TFP6 3 5

FIGURE 3

115 K-FACTOR, 3/4 INCH NPTUPRIGHT AND PENDENT FLAT SPRAY SPRINKLERS

FIGURE 4MODEL G1 GUARD

TYPICAL INSTALLATION ON UPRIGHT AND PENDENT FLAT SPRAY SPRINKLERS

Components:

60 mm

MAKE-IN

NOMINAL13 mm

WRENCHFLATS

UPRIGHT

MAKE-INNOMINAL

PENDENT

46 mm

60 mm

13 mm

*CROSS SECTION

BULBSIZE

MODELSIN

UPRIGHT

TY41363 mmTY-FRFS


TY-FS 5 mm TY4156

PENDENT

TY4256

TY4246

TY4236

2

6

45

3

1

*

Frame

ButtonBulb (See table above)Compression ScrewDeflector

Sealing Assembly--

---

- *2

1

3

5

4

6

THREADRELIEF


*can be provided on special request.Pipe thread connections per ISO 7/1**

on frame.

*DEFLECTORPLATE SEATINGESCUTCHEON

SURFACE

SHIELD AND

3/4" NPT

DEFLECTOR3/4" NPT **

**

73 mm DIA.

60 mm

UPRIGHT

BAR

(ENGAGED)GUARD CLIP

SPRINKLER

GUARD

MODEL G1

PLATE

THREAD RELIEF

PENDENT

BASE

PENDENT

SPRINKLER

FLAT SPRAY

UPRIGHT or

15 or 20 mm

ENGAGED BY

BASE PLATE


5/10

TFP6 3 5 P a g e 5 o f 1 0

FIGURE 5K80 PENDENT FLAT SPRAY SPRINKLERS

WITHMODEL H1 SHIELD

ORMODEL H1 SHIELD AND MODEL G1 GUARD

GUARD

MODEL G1

SHIELD

MODEL H1

SEATING

SHIELD

SURFACE

8 mm

100 mm DIA.

FLAT SPRAY

SPRINKLER

PENDENT15 mm

SHIELDMODEL H1

SURFACE

SEATING

SHIELD

ATTACHMENT

SPRING

15 mm

FLAT SPRAY

SPRINKLER

PENDENT

FIGURE 6K80 PENDENT FLAT SPRAY SPRINKLERSWITH

MODEL H2 SHIELDOR

MODEL H2 SHIELD AND MODEL G1 GUARD

FLAT SPRAYSPRINKLER

GUARDMODEL G1

SHIELDMODEL H2

PENDENT

SEATING

SHIELD

SURFACE

15 mmPENDENT

SPRINKLERFLAT SPRAY

15 mmMODEL H2SHIELD

160 mm DIA.

32 mm

SEATING

SHIELD

SURFACEATTACHMENTSPRING


6/10

P a g e 6 o f 1 0 TFP6 3 5


WITHMODEL H1 SHIELD


SEATING

SHIELD

SURFACEATTACHMENT

SPRING

8 mm

SURFACE

SEATING

SHIELD

ATTACHMENT

SPRING

GUARD

MODEL G1

SHIELD

MODEL H1

FLAT SPRAY

SPRINKLER

PENDENT

20 mm

SHIELD

MODEL H1

20 mm

FLAT SPRAY

SPRINKLER

PENDENT

100 mm DIA.


WITHMODEL H2 SHIELD


160 mm DIA.

32 mm

SEATINGSHIELD


FLAT SPRAYSPRINKLER

GUARDMODEL G1

SHIELDMODEL H2

PENDENT

SEATINGSHIELD


20 mmPENDENT

20 mm

SPRINKLERFLAT SPRAY

MODEL H2SHIELD


7/10

InstallationInstallation instructions are provided inthe following subsections:

Sprinkler Only

Sprinkler With Guard

Sprinkler With Shield

Sprinklers With Guard & Shield

SPRINKLER ONLY

The Model TY-FRFS, TY-FS Special,and TY-FS Sprinklers must be in-stalled in accordance with the follow-ing instructions:

NOTESDo not install any bulb type sprinkler ifthe bulb is cracked or there is a loss ofliquid from the bulb. With the sprinklerheld horizontally, a small air bubbleshould be present. The diameter of theair bubble is approximately 1/16 inch(1,6 mm) for the 135F/57C to 3/32inch (2,4 mm) for the 360F/182Ctemperature ratings.

A leak tight 1/2 inch NPT sprinkler jointshould be obtained with a torque of 7to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-mum of 21 ft. lbs. (28,5 Nm) of torquemay be used to install sprinklers with1/2 NPT connections. A leak tight 3/4inch NPT sprinkler joint should be ob-tained with a torque of 10 to 20 ft.lbs.(13,4 to 26,8 Nm). A maximum of 30ft.lbs. (40,7 Nm) of torque is to be used

to install sprinklers with 3/4 NPT con-nections. Higher levels of torque maydistort the sprinkler inlet and causeleakage or impairment of the sprinkler.

Do not attempt to make-up for insuffi-cient adjustment in the escutcheonplate by under- or over-tightening thesprinkler. Readjust the position of thesprinkler fitting to suit.

Step 1. Pendent sprinklers are to beinstalled in the pendent position, andupright sprinklers are to be installed inthe upright position.

Step 2. With pipe thread sealant ap-plied to the pipe threads, hand tighten

the sprinkler into the sprinkler fitting.

Step 3. Tighten the sprinkler into thesprinkler fitting using only the W-Type6 Sprinkler Wrench (Ref. Figure 10).With reference to Figures 1, 2, and 3the W-Type 6 Sprinkler Wrench is tobe applied to the wrench flats.

SPRINKLER WITH GUARD

With reference to Figure 4, the ModelG1 Guard must be installed as follows:

S t e p 1 . The G1 Guard i s to be

mounted on the sprinkler after thesprinkler has been installed in accord-ance with the Sprinklers Only sub-section.

Step 2. With the Clips loose, firstspread the two halves of the SprinklerGuard just enough to pass by thesprinkler deflector from the side. Then,once again spread the two halves ofthe Sprinkler Guard just enough topass over the sprinkler thread reliefportion of the sprinkler. (Refer to Fig-ures 2 and 3.)

Step 3. With the Sprinkler Guard posi-tioned on the thread relief portion ofthe sprinkler, as applicable, engagethe Clips and then slide the Clips untilthey seat against the Base to completethe installation as shown in Figure 4.

To help assist with the sliding of theClips, the Guard Installation Tool maybe used as shown in Figure 9. In addi-

tion, pliers can be used to facilitate thefinal seating of he Clips.

NOTESThe Clips must seat against the Basein order to be considered fully seated

and in order to complete the installa-tion.

The G1 may be located in any positionrelative to the sprinkler frame arms.

SPRINKLER WITH SHIELD

With reference to Figures 5, 6, 7, or 8,the Model H1 or Model H2 Shield mustbe installed as follows:

Step 1. Pendent sprinklers are to beinstalled in the pendent position.

Step 2. With pipe thread sealant ap-

FIGURE 9MODEL G-1 GUARD INSTALLATION PROCEDURE

WITH INSTALLATION TOOL APPLIED OVER

TOWARD BASE PLATES UNTIL FULLY ENGAGED

ADJACENT BARS, PRESS SECOND CLIP

SWIVEL CLIPS OVER

INSTALLED, CAREFULLY

AND FIT ONTO SPRINKLER

TOWARD BASE PLATES

ADJACENT BARS AND SLIDE

SPREAD BASE PLATES APART

PLATESBASE

FIRST

CLIP INSTALLATIONTOOL (SHIPPED WITH

GUARDS)

CLIP FULLYENGAGED

SLOTBAR

CLIP FULLYENGAGED

SECOND

A PLIER

USEDMAY BE

INSTALLATIONTOOL

CLIP

CLIP

TOOLINSTALLATION

CLIP

CLIP

WITH SPRINKLER PROPERLY

THREAD RELIEF

UNTIL SNUG

MODEL G1GUARD

FLAT SPRAYSPRINKLER

FIGURE 10W-TYPE 6 SPRINKLER

WRENCH

WRENCH RECESS(END "A" USED FOR

ISO 7/1-R 3/8 &

WRENCH RECESS(END "B" USED FOR

3/4" NPT MODELS)

1/2" NPT MODELS)

FIGURE 11W-TYPE 7 SPRINKLER

WRENCH

RECESSWRENCH

WITH SPRINKLERENGAGEMENTIN TO ENSURE

WRENCHINGAREA

PUSH WRENCH

TFP6 3 5 P a g e 7 o f 1 0


8/10

plied to the pipe threads, install theShield over the sprinkler threads.

Step 3. Install the Attachment Springover the sprinkler threads until it seatsagainst the Shield.

Step 4. Hand tighten the sprinkler intothe sprinkler fitting.

Step 5. Tighten the sprinkler into thesprinkler fitting using only the W-Type7 Sprinkler Wrench (Ref. Figure 11).The wrench is to be applied to thesprinkler wrenching area shown in Fig-ures 2 or 3, as applicable.

NOTEWhen installed correctly, the Attach-ment Spring wi l l be sl ightly com-pressed and the Shield will be heldfirmly in place.

SPRINKL ER WIT H GUARD ANDSHIELD

With reference to Figures 5, 6, 7 or 8,the guard with shield arrangementmust be installed as follows:

Step 1. Pendent sprinklers are to beinstalled in the pendent position.

Step 2. With pipe thread sealant ap-plied to the pipe threads, install theShield over the sprinkler threads.

Step 3. When installing K115 Sprin-klers, Install the Attachment Springover the sprinkler threads until it seatsagainst the Shield.

NOTE

An Attachment Spring is not utilized forK80 Sprinklers with Guard and Shield.

Step 4. Hand tighten the sprinkler intothe sprinkler fitting.

Step 5. Tighten the sprinkler into thesprinkler fitting using only the W-Type7 Sprinkler Wrench (Ref. Figure 11).The wrench is to be applied to thesprinkler wrenching area shown in Fig-ures 2 or 3, as applicable.

Step 7. After the sprinkler with shieldis installed into the sprinker pipe fitting,install the guard as described in theSprinkler With Guard sub-section.

Care andMaintenanceThe Model TY-FRFS, TY-FS Special,and TY-FS Sprinklers must be main-tained and serviced in accordance

with the following instructions:

NOTESBefore closing a fire protection systemmain control valve for maintenancework on the fire protection system thatit controls, permission to shutdown theaffected fire protection system must beobtained from the proper authoritiesand all personnel who may be affectedby this action must be notified.

Sprinklers that are found to be leakingor exhibiting visible signs of corrosionmust be replaced.

Automatic sprinklers must never be

painted, plated, coated or otherwisealtered after leaving the factory. Modi-f ied sprinklers must be replaced.Sprinklers that have been exposed tocorrosive products of combustion, buthave not operated, should be replacedif they cannot be completely cleanedby wiping the sprinkler with a cloth orby brushing it with a soft bristle brush.

Care must be exercised to avoid dam-age to the sprinklers - before, during,and after installation. Sprinklers dam-aged by dropping, striking, wrenchtwist/slippage, or the like, must be re-placed.Also, replace anysprinkler thathas a cracked bulb or that has lostliquid from its bulb. (Ref. InstallationSection).

Proper installation of sprinklers in-stalled with guards, shields, or guardswith shields should be verified duringthe annual visual inspection of thesprinklers.

The owner is responsible for the in-spection, testing, and maintenance oftheir fire protection system and de-vices in compliance with this docu-ment, as well as with the applicablestandards of the Approval agency andstandards of any other authorities hav-ing jurisdiction. The installing contrac-tor or sprinkler manufacturershouldbecontacted relative to any questions.

It is recommended that automaticsprinkler systems be inspected,tested, and maintained by a qualifiedInspection Service in accordance withlocal requirements and/or nationalcodes.

LimitedWarrantyProducts manufactured by Tyco Fire &Building Products (TFBP) are war-ranted solely to the original Buyer for

ten (10) years against defects in mate-rial and workmanship when paid forand properly installed and maintainedunder normal use and service. Thiswarranty will expire ten (10) yearsfrom date of shipment by TFBP. Nowarranty is given for products or com-ponents manufactured by companiesnot affiliated by ownership with TFBPor for products and components whichhavebeen subjectto misuse, improperinstallation, corrosion, or which havenot been installed, maintained, modi-fied or repaired in accordance with thestandards recognized by the Approvalagency, as well as the standards of

any other Authorities Having Jurisdic-tion. Materials found by TFBP to bedefective shall be either repaired orreplaced, at TFBPs sole option. TFBPneither assumes, nor authorizes anyperson to assume for it, any other ob-ligation in connection with the sale ofproducts or parts of products. TFBPshall not be responsible for sprinklersystem design errors or inaccurate orincomplete information supplied byBuyer or Buyers representatives.

In no event shall TFBP be liable, incontract, tort, strict liability or underany other legal theory, for incidental,indirect, special or consequential dam-ages, including but not limited to laborcharges, regardless of whether TFBPwas informed about the possibility ofsuch damages, and in no event shallTFBPs liability exceed an amountequal to the sales price.

The foregoing warranty is made in lieuof any and all other warranties, ex-press or implied, including warrantiesof merchantability and fitness for aparticular purpose.

This limited warranty sets forth the ex-clusive remedy for claims based onfailure of or defect in products, materi-als or components, whether the claimis made in contract, tort, strict liabilityor any other legal theory.

This warranty will apply to the full ex-tent permitted by law. The invalidity, inwhole or part, of any portion of thiswarranty will not affect the remainder.

P a g e 8 o f 1 0 TFP6 3 5


9/10

OrderingProcedureWhen placing an order, indicate the fullproduct name. Refer to the Price Listfor complete listing of Part Numbers.

NOTESprinklers, wrenches, guards, shields,attachment springs, and additional clipinstallation tool are all sold separately

Contact your local distributor for avail-ability.

Sprinklers:Specify: (Specify Model/SIN), (SpecifyStandard Response, Special Re-sponse, or Quick Response, (specifyK-factor), (specify temperature rating),(specify Pendent or Upright) Sprinkler,P/N (specify from Table A).

Sprinkler Wrenches:Specify: W-Type (specify) SprinklerWrench, P/N (specify).

W-6. . . . . . . . . . . . . . . . . . . . . P/N 56-000-6-387W-7. . . . . . . . . . . . . . . . . . . . . P/N 56-850-4-001

Guards:Specify: Model G-1 Guard having

(specify) finish, P/N (specify).

Red Painted . . . . . . . . . . . . . . P/N 56-000-6-387Zinc Chromate . . . . . . . . . . . . P/N 56-850-4-001

Shields:Specify: Model (specify), (specify NPTsize) Shield , P/N (specify).

H1, 1/2" NPT . . . . . . . . . . . . . P/N 22521H1, 3/4" NPT . . . . . . . . . . . . . P/N 22522H2, 1/2" NPT . . . . . . . . . . . . . P/N 22529H2, 3/4" NPT . . . . . . . . . . . . . P/N 22524

Attachment Springs:Specify: (specify NPT size) ShieldSpring, P/N (specify).

1/2" NPT . . . . . . . . . . . . . . . . . P/N 225263/4" NPT . . . . . . . . . . . . . . . . . P/N 22527

Additional* Clip Installation Tools:specify: Clip Installation Tool for G1

Guard, P/N 56-000-8-597.

* The Clip Installation Tool is includedwith guard orders in original cartons.

P/N 51 XXX 1 XXX

68C (Red)155

TEMPERATURE

RATING

(Fluid Color)

57C (Orange)1351

SPRINKLER

MATERIAL

TABLE APART NUMBER SELECTIONFLAT SPRAY SPRINKLERS

79C (Yellow)

286

93C (Green)200

141C (Blue)

175

NATURAL BRASS

MODEL/SIN

391 115K PENDENT, 3/4 INCH NPT

382 57K PENDENT, ISO 7/1-R 3/8

370 80K UPRIGHT, 1/2 INCH NPT

TY-FRFS/TY1236

TY-FRFS/TY3136

TY-FRFS/TY4236

371

390

80K PENDENT, 1/2 INCH NPT

115K UPRIGHT, 3/4 INCH NPT

TY-FRFS/TY3236

TY-FRFS/TY4136

482 57K PENDENT, ISO 7/1-R 3/8TY-FS Special/TY1246

470 80K UPRIGHT, 1/2 INCH NPTTY-FS Special/TY3146

471 80K PENDENT, 1/2 INCH NPTTY-FS Special/TY3246

490 115K UPRIGHT, 3/4 INCH NPTTY-FS Special/TY4146

491 115K PENDENT, 3/4 INCH NPTTY-FS Special/TY4246

582 57K PENDENT, ISO 7/1-R 3/8TY-FS/TY1256

570 80K UPRIGHT, 1/2 INCH NPTTY-FS/TY3156

571 80K PENDENT, 1/2 INCH NPTTY-FS/TY3256

590 115K UPRIGHT, 3/4 INCH NPTTY-FS/TY4156

591 115K PENDENT, 3/4 INCH NPTTY-FS/TY4256

380 TY-FRFS/TY1136 57K UPRIGHT, ISO 7/1-R 3/8

480 TY-FS Special/TY1146 57K UPRIGHT, ISO 7/1-R 3/8

580 TY-FS/TY1156 57K UPRIGHT, ISO 7/1-R 3/8

TFP6 3 5 P a g e 9 o f 1 0


10/10

P a g e 1 0 o f 1 0 TFP6 3 5

TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446

flat spray sprinkler

Documents