elemental bill of quantities for 3 bedroom apartment block

7/24/2019 Elemental Bill of Quantities for 3 Bedroom Apartment Block

1/29

CONSTRUCTION OF THREE BEDROOM FLAT

ITEM DESCRIPTION UNIT QTY RATE AMOUNT

GROUP ELEMENT Nr. 1 SUBSTRUCTURE

SUBSTRUCTURE (PROVISIONAL)

D GROUNDWORK

D20 EXCAVATING AND FILLING

EXCAVATING IN NORMAL FIRM GROUND

Site Pre aration

A Clearing site vegetation, bushes, shrubs, undergrowth,

hed es and trees

m2 409 35 14,315.00

Excavation

B Excavating topsoil average 150mm deep m2 409 100 40,900.00

Reduced level excavation

C maximum de th; not exceedin 250mm dee m2 51 220 11,220.00

Trench Excavation

D Excavating trench width exceeding 0.30m maximum

de th not exceedin 2.00m

m3 184 650 119,600.00

E Excavation in rock laterite and disposal of excavated

materials as directed

m3 20 1,150 23,000.00

Pits for concrete foundation; (47 Nr.)

F Excavating pits (47nr), maximum depth not exceeding

2.00m

m3 28 650 18,200.00

Disposal

G Excavated material; on site as directed; in spoil

maximum distance not exceedin 50m

m3 115 250 28,750.00

Filling to excavations

H Filling to excavations, average thickness exceeding

0.25m; arising from the excavations; Compacted around

foundations

m3 117 190 22,230.00

Granular materials

J Filling to make up levels, average thickness exceeding

250mm, laterite materials obtained off site.

m2 82 750 61,500.00

Carried to Collection 339,715.00

0 NOVEMBER 2015


2/29



SUBSTRUCTURE (Cont'd)

Rock laterite hardcore

A Boulder rock; hardcore exceeding 250mm thick;

obtained offsite; depositing in layers 150mm maximum

thickness; com acted and consolidated under beds

m3 82 2,400 196,800.00

Surface Treatment

Pesticides: Dieldrex 20 anti-termite

B Treating the bottom, sides and surface of excavation m2 1437 50 71,850.00

E10: INSITU CONCRETE

Plain Insitu Concrete

Vibrated Grade 30.

C Blinding beds, thickness not exceeding 50mm thick;

oured on or a ainst earth

m3 9 14,500 130,500.00

Plain Insitu Concrete

Vibrated Grade 30.

D Foundations, 150 - 450mm thick m3 35 23,000 805,000.00

Reinforced Insitu Concrete

Vibrated Concrete Grade 30

Column bases m3 24 25,000 600,000.00

E Regular columns m3 3 25,000 75,000.00

Beds; 150mm thick m3 44 25,000 1,100,000.00

E20: FORMWORK FOR IN SITU CONCRETE

Sawn formwork to:

F Sides of column bases m2 72 1,100 79,200.00

G Sides of Regular columns m2 80 1,100 88,000.00

H Sides of floor bed m 121 165 19,965.00

Carried to Collection 3,166,315.00

1 NOVEMBER 2015


3/29



E10: INSITU CONCRETE

E30: REINFORCEMENT FOR IN SITU CONCRETE

High tensile bars to BS 4449, striaght (provisional)

A 20mm - 10mm Diametre bars t 2 180,000 360,000.00

Mild steel bars to BS 4449, bent (provisional)

B 10mm - 6mm Diametre bars t 1.72 180,000 309,600.00

Fabric mesh A142 weighing 2.22kg/m2 laid as detailed

in manufacturer's manual

C Ground floor beds m2 287 650 186,550.00

F10: BRICK/BLOCK WALLING

BLOCKWORK; 225mm x 450mm Nominal; laid in

stretcher bond; cement and sand mortar (1:3)

D 230mm filled solid with concrete grade 15 in foundation m2 205 3,200 656,000.00

E 150mm ditto m2 39 2,100 81,900.00

F 0.13mm damp proof membrane laid with melted joint on

and including 10mm layer of fine sand (Measured

se aratel

m2 287 235 67,445.00


Collection

AYB/GA/3BF/1 339,715.00

AYB/GA/3BF/2 3,166,315.00

AYB/GA/3BF/3 1,661,495.00

GROUP ELEMENT NR. 1: SUBSTRUCTURE

CARRIED TO SUMMARY 5,167,525.00

2 NOVEMBER 2015


4/29



GROUP ELEMENT NR. 2: SUPERSTRUCTURE

ELEMENT NR.2A FRAME

E10: In situ Concrete

Reinforced insitu concrete

Vibrated concrete grade 25

A Regular Columns m3 16 25,000 400,000.00

B Beams m3 19 25,000 475,000.00

E20: Formwork for in situ concrete

Sawn formwork to:

C Sides of regular Columns m2 275 1,100 302,500.00

D Sides and soffits of Beams m2 231 1,100 254,100.00

E30: Reinforcement for in situ concrete

High tensile bars to BS 4449, straight (provisional)

E 20 - 10mm Diametre bars t 2.44 180,000 439,200.00

Mild steel bars to BS 4449, bent (Provisional)

F 10-6mm Diametre bars t 2 180,000 360,000.00

ELEMENT NR.2A FRAMES


3 NOVEMBER 2015


5/29



ELEMENT NR.2B UPPER FLOORS




A Slabs thickness not exceeding 150mm, slope not

exceeding 15

m3 42 25,000 1,050,000.00


Sawn formwork to:

B Soffits of slabs, slab thickness not exceeding 200mm,

slope not exceeding 15

m2 280 1,100 308,000.00

C Edges of suspended slabs, height not exceeding 250mm m 140 275 38,500.00



D 20 - 10mm Diametre bars t 3.5 180,000 630,000.00


E 10-6mm Diametre bars t 1.54 180,000 277,200.00

ELEMENT NR.2B UPPER FLOORS


4 NOVEMBER 2015


6/29



ELEMENT NR.2C ROOF




A Roof Beams/Cantilever m3 23 25,000 575,000.00


Sawn formwork to:

B Beams m2 442 1,100 486,200.00



C 20 - 10mm Diametre bars t 2 180,000 360,000.00


D 10-6mm Diametre bars t 1.22 180,000 219,600.00

H: CLADDING/COVERING

H72: Aluminium sheet coverings/flashing

Stone coated step tiles or other approved industrial

coloured Aluminium roofing sheets and accessories

lapped and fixed to steel purlins (measured separetely)

in accordance with manufacturer's details.

E Roof Covering m2 961 4,250 4,084,250.00

Carpentary/Timber framing/First fixing

Wrot treated hardwood in:

F 150x50mm tie beam m 443 350 155,050.00

G 150x50mm rafter m 390 350 136,500.00

H 150x50 kin ost m 161 350 56,350.00

J 100x50mm struts m 402 250 100,500.00

K 75x50mm purlin m 421 200 84,200.00

L 50x50mm noggins m 435 120 52,200.00

M 300 x 300mm; Concrete Fascia m 200 6,000 1,200,000.00

ELEMENT NR. 2C ROOF


5 NOVEMBER 2015


7/29



ELEMENT NR.2D STAIRS AND RAMPS




A Staircases m3 5 25,000 125,000.00


Sawn formwork to:

B Stairflights (3Nr); landing slab not exceeding 200mm

thick; 1500mm wide

m 52 1,100 57,200.00

C Sloping soffits of stairs m2 10 1,100 11,000.00





E 10-6mm Diametre bars t 0.11 180,000 19,800.00

M20:Plastered/Rendered/Roughcast coatings

15mm thick cement and sand (1:3) smooth rendering

F Landings soffits, width exceeding 300mm m2 6 650 3,900.00

G Sloping soffits of staircase width exceeding 300mm m2 13 650 8,450.00

M: SURFACE FINISHES

M10: Sand cement/ Concrete/Granolithic

screeds/flooring

42mm thick cement and sand (1:3) screeded bed

H Stairflights (3Nr); landing slab not exceeding 200mm

thick; 1500mm wide

m2 6 1,450 8,700.00

J Sloping soffits of stairs m2 13 1,450 18,850.00


6 NOVEMBER 2015


8/29



STAIRCASES (Cont'd)

M40:STONE/CONCRETE/QUARRY/CERAMIC

TILING/MOSAIC/GRANITE/VITRIFIED TILING

M41: TILING

600x600x8mm thick tiles with including cement mortaron screeded bed (Measured separately)

A Stairflights (3Nr); landing slab not exceeding 200mm

thick; 1500mm wide

m2 6 4,500 27,000.00

B Sloping sides of stairs m 13 1,350 17,550.00

M60: PAINTING/CLEAR FINISHING

PREPARE AND APPLY PRIME COAT AND TWO

FINISHING COATS OF EMULSION PAINTS ON

RENDERED WALLS

General surfaces

C Stairflights (3Nr); landing slab not exceeding 200mm

thick; 1500mm wide

m2 6 800 4,800.00

D Sloping sides of stairs m2 13 800 10,400.00

L30: Stairs/Walkways/Balustrades

METAL WORK

MILD STEEL GRADE 43 BS 4360 IN STAIR

BALUSTRADE SITE WELDED

E 6 x 50mm flat core rail welded to balustrade m 25 1,200 30,000.00

F Mitred and welded angle Nr 15 1,500 22,500.00

G 50x50mm square hollow balusters 1000mm high, one end

embedded in concrete 100mm deep and the other

welded to core rail.

Nr 20 1,350 27,000.00


KNOT, PRIME, STOP, PREPARE AND APPLY TWO

FINISHING COATS OF GLOSS PAINT AS

SPECIFIED

General Surfaces

H Metal work not exceeding 300mm girth m 60 800 48,000.00

Carried To Collection 187,250.00

Collection

AYB/GA/3BF/7 346,500.00

AYB/GA/3BF/8 187,250.00

ELEMENT Nr. 2D STAIRS AND RAMPS

CARRIED TO SUMMARY 533,750.00

7 NOVEMBER 2015


9/29



ELEMENT NR. 2E EXTERNAL WALLS

F10 BRICK/BLOCK WALLING

BLOCKWORK; 225 x 450mm Nominal; laid in

stretcher bond; cement mortar (1:3)

A 230mm thick hollow blocks m2 486 2,600 1,263,600.00

ELEMENT NR. 2E EXTERNAL WALLS


8 NOVEMBER 2015


10/29



ELEMENT NR. 2F WINDOWS AND EXTERNAL

DOORS

E10: In situ concrete


Vibrated grade 20

A Isolated Lintels m3 14 25,000 350,000.00


Sawn formwork to:

B Sides and Soffits of isolated lintels m2 177 1,100 194,700.00

E30: Reinforcement for insitu concrete

High tensile bars to BS 4449, straight (Provisional)

C 12mm Diametre bars t 1.23 180,000 221,400.00



L21: METAL DOORS/SHUTTERS/HATCHES

Swing door complete with all accessories, Anodized

aluminium green powder coated frame with 5mm thick

top fixed glazing including Ironmongery designed to

Arhcitect's details, built into blockwork and concrete

surround, bedded and pointed in cement sand mortar

E Steel panel entrance double leaf door, size 1500 x

2100mm high and including frame

Nr 4 100,000 400,000.00

F Ditto 900 x 2100mm high Nr 4 30,000 120,000.00

L11:METAL WINDOWS / ROOFLIGHTS /SCREENS

/LOUVRES

Projected windows in 5mm thick anodized glass framed

in powder coated Aluminium blue profiles complete with

flyscreen and purpose made 12mm rod in grid burglar-

proofed grille to Architect's details, all built into

blockwork and concrete surround bedded and pointed in

G Projected windows size 1500 x 1200mm high overall Nr 8 72,000 576,000.00

H Ditto size 1200 x 1200mm high Nr 16 57,600 921,600.00

J Ditto size 900 x 600mm high overall Nr 8 21,600 172,800.00

K Ditto size 600 x 600mm high Nr 16 14,400 230,400.00

Element Nr. 2F WINDOWS AND EXTERNAL DOORS


9 NOVEMBER 2015


11/29



ELEMENT NR: 2G INTERNAL WALLS AND

PARTITIONS

F10 BRICK/BLOCK WALLING

BLOCKWORK; 225mm x 450mm nominal; laid in

stretcher bond; cement mortar (1:3)

A 150mm thick hollow blocks m2 569 2,100 1,194,900.00

Element Nr. 2G INTERNAL WALLS


10 NOVEMBER 2015


12/29



ELEMENT NR. 2H INTERNAL DOORS

E10: In situ concrete


Vibrated grade 20

A Isolated Lintels m3 3 25,000 75,000.00


Sawn formwork to:

B Sides and Soffits of isolated lintels m2 38 1,100 41,800.00

E30: Reinforcement for insitu concrete

High tensile bars to BS 4449, straight (Provisional)

C 12mm Diametre bars t 0.27 180,000 48,600.00



L21: METAL DOORS/SHUTTERS/HATCHES

KFCC or Wood kraft or other equal approved Masonia

faced polished 44mm solid core finish doors to BS 459

part 2 faced both sides with 5mm external quality

masonia plywood and prefinished hardwood lipped all

round and blocked out for ironmon er

E Overall size 900 x 2100mm high Nr 16 23,000 368,000.00

F Ditto 750 x 2100mm high Nr 20 23,000 460,000.00

M60:PAINTING/CLEAR FINISHING

KNOT, PRIME, STOP, PREPARE AND APPLY TWO

FINISHING COATS OF GLOSS PAINT AS SPECIFIED

General Surfaces

G Metal door frames not exceeding 300mm girth m 88 600 52,800.00

Element Nr. 2H INTERNAL DOORS


11 NOVEMBER 2015


13/29



SUMMARY

GROUP ELEMENT NR. 2 SUPERSTRUCTURE

1 ELEMENT NR. 2A FRAMES 2,230,800.00

2 ELEMENT NR. 2B UPPER FLOORS 2,303,700.00

3 ELEMENT NR. 2C ROOF 7,509,850.00

4 ELEMENT NR. 2D STAIRS AND RAMP 533,750.00

5 ELEMENT NR. 2E EXTERNAL WALLS 1,263,600.00

6 ELEMENT NR. 2F WINDOWS AND EXTERNAL DOORS 3,282,300.00

7 ELEMENT NR. 2G INTERNAL WALLS & PARTITIONS 1,194,900.00

8 ELEMENT NR. 2H INTERNAL DOORS 1,066,000.00

GROUP ELEMENT NR. 2 SUPERSTRUCTURE


12 NOVEMBER 2015


14/29



GROUP ELEMENT NR. 3 FINISHES

ELEMENT NR. 3A WALL FINISHES

M20 PLASTERED/RENDERED/ROUGHCAST

COATINGS

15mm thick cement and sand (1:5); Plain rendering;

finishing trowelled smooth

Walls

A Surfaces over 300mm wide; internal m2 1238 500 619,000.00

B Surfaces not exceeding 300mm wide; internal m 950 210 199,500.00



Walls

C Surfaces over 300mm wide; internal m2 988 500 494,000.00

D Surfaces not exceeding 300mm wide; internal m 512 210 107,520.00

M40: STONE/CONCRETE/ QUARRY/CERAMIC

TILING/ MOSAIC/GRANITE/VITRIFIED TILING

300X200X8mm thick glazed ceramic wall tiles of

approved colour bedded and jointed in cement mortar onscreeded backing (measured separately) and grouted in

white cement including all necessary round edge tile to:

Walls

E Over 300mm wide; internal at toilet m2 323 1,800 581,400.00

F Ditto; surfaces not exceeding 300mm wide m 35 540 18,900.00

12mm thick cement and sand (1:3) screeded backing

G Walls; width exceeding 300mm wide m2 323 500 161,500.00

H Walls; width not exceeding 300mm wide m 35 168 5,880.00


13 NOVEMBER 2015


15/29



WALL FINISHES (Cont'd)



FINISHING COATS OF EMULSION PAINTS ONRENDERED WALLS

General Surfaces

A Walls over 300mm girth; Internal m2 1238 450 557,100.00

B Ditto surfaces not exceeding 300mm wide m 950 135 128,250.00

PREPARE AND APPLY ONE PRIME COAT AND TWO

FINISHING COATS OF TEXTURED PAINTS AS

SPECIFIED

General Surfaces

C Walls over 300mm girth; External m2 988 500 494,000.00

D Ditto surfaces not exceeding 300mm wide m 512 150 76,800.00

E Screeding to walls over 300mm girth (Externally andInternally)

m2 2226 500 1,113,000.00

F Ditto surfaces not exceeding 300mm wide m 1,462 150.00 219,300.00


Collection

AYB/GA/3BF/14 2,187,700.00

AYB/GA/3BF/15 2,588,450.00

Element Nr. 3A WALL FINISHES


14 NOVEMBER 2015


16/29



ELEMENT NR. 3B FLOOR FINISHES

M SURFACE FINISHES

CEMENT - SAND (1:3) BEDS AND BACKINGS; TO

RECEIVE SUBSEQUENT FINISH

Floors; over 300mm wide

A 42mm thick average; screeded bed; to falls only not

exceeding 15 degrees from the horizontal to receive

fully vitrified ceramic tiles

m2 567 500 283,500.00

B Ditto not exceeding 300mm wide m 210 180 37,800.00

M40: STONE/CONCRETE/ QUARRY/CERAMIC

TILING/ MOSAIC/GRANITE/VITRIFIED TILING

600X300X8mm thick glazed ceramic wall tiles of

approved colour bedded and jointed in cement mortar

on screeded backing (measured separately) and

grouted in white cement including all necessary round

edge tile to:

C Floors; level and to falls only not exceeding 15 degrees

from horizontal; Internal

m2 567 2,800 1,587,600.00

D Ditto; not exceeding 300mm wide m 10 1,050 10,500.00

E Skirtings; height 100mm including backing; Internal m 210 319 66,990.00

ELEMENT NR. 3B FLOOR FINISHES


15 NOVEMBER 2015


17/29



ELEMENT NR. 3C CEILING FINISHES

M20 PLASTERED/RENDERED/ROUGHCAST

COATINGS



A Soffit of suspended slab exceeding 300mm wide;

Internal

m2 287 600 172,200.00



FINISHING COATS OF EMULSION PAINTS ON

RENDERED WALLS

General Surfaces

B Soffit of suspended slab exceeding 300mm wide;

Internal

m2 287 680 195,160.00

K LINING/SHEETING/DRY PARTITION

C Plaster of paris (POP) ceiling to Architect's design m2 287 3,000 861,000.00

Element Nr. 3C CEILING FINISHES


16 NOVEMBER 2015


18/29



SUMMARY

1 GROUP ELEMENT NR. 3 FINISHES

2 ELEMENT NR 3A WALL FINISHES 4,776,150.00

3 ELEMENT NR 3B FLOOR FINISHES 1,986,390.00

4 ELEMENT NR 3C CEILING FINISHES 1,228,360.00

GROUP ELEMENT NR 3 FINISHES

CARRIED TO GENERAL SUMMARY 7,990,900.00

17 NOVEMBER 2015


19/29



GROUP ELEMENT NR. 4 FITTINGS, FURNISHING

AND EQUIPMENT

ELEMENT NR. 4A GENERAL FITTINGS,

FURNISHINGS AND EQUIPMENT

N FURNITURE/EQUIPMENT

N20: SPECIAL PURPOSE FIXTURES

/FURNISHINGS/EQUIPMENT

A Kitchen Cabinets Nr 4 150,000 600,000.00

GROUP ELEMENT NR. 4 FITTINGS, FURNISHING

AND EQUIPMENT

CARRIED TO GENERAL SUMMARY 600,000.00

18 NOVEMBER 2015


20/29



GROUP ELEMENT NR. 5 SERVICES

ELEMENT NR. 5A ELECTRICAL SERVICES

V20: LV DISTRIBUTION

Equipment; Metal clad Main distribution board

surface/flush type as manufactured by FEDERAL

ELECTRIC or MEM or BILLS including all MCB, back

outlet connections to flush adaptable boxes, including

earth bonding, labels and fixing in accordance with

A Floor standing CUBICON switch board mv panel TP&N

main MCB

Nr 1 160,500 160,500.00

B 100A 10-way TP & N MCB Distribution board comprising

of 4nr 5A stablocks, 7nr 10A stablocks; 2nr. 20A

stablocks, 2nr 30A stablocks and 3nr Spares consisting

of 3nr 5A stablocks

Nr 4 42,000 168,000.00

Equipment; Metal clad isolating pattern switches or

ELCB as manufactured by FEDERAL ELECTRIC, MEM or

BILLS including all necessary fuse links with quick make

and quick breaks contacts and fixing in accordance with

manufacturers instructions

C 100A TP&N ELCB Isolating fused switch Nr 4 25,000 100,000.00

V21: GENERAL LIGHTING

Lamps and Luminaires; as manufactured by PHILIPS,

THORN, BEGA, TRILUX or other approved; rates to

include for supply, installation and accessories necessary

for com lete installation

D 1 x 100W Gino chandellier wall bracket Nr 24 1,800 43,200.00

E 3 x 100W Rise and fall dining lighting fitting Nr 4 6,500 26,000.00

F 5 x 100W Rise and fall Gino chandellier fitting Nr 4 7,200 28,800.00

G 1 x 100W Ceiling mounted light fitting Nr 48 2,850 136,800.00

H 1 x 100W Screw neck fitting Nr 16 2,500 40,000.00

J 1 x 100W Super club CD ceiling mounted fitting Nr 12 2,650 31,800.00

K 1 x 100W Compact reccess ceiling mounted finish Nr 20 1,850 37,000.00

L 1 x 18W Mirror shavers light Nr 16 2,100 33,600.00

M 1 x 100W bulkhead water resistant fitting Nr 20 4,800 96,000.00


19 NOVEMBER 2015


21/29



V21: GENERAL LIGHTING (Cont'd)

A 1 x 100W bulkhead fitting (Roller) Nr 28 1,850 51,800.00

B 1 x 100W adjustable retractable sport light Nr 20 1,850 37,000.00

C 1 x 100W Bedhead reading lamp with self control switch Nr 12 1,850 22,200.00

D 1 x 100W Ceiling rose for water heater Nr 16 1,850 29,600.00

E 70W Newclime Ceiling fan Nr 16 7,800 124,800.00

F 1 - gang, 1 - way 5A light switch Nr 16 655 10,480.00

G 2 - gang, 2 - way 5A light switch Nr 48 950 45,600.00

H 1 - gang, 2 - way 5A light switch Nr 10 690 6,900.00

J 3 - gang, 1 - way 5A light switch Nr 10 1,100 11,000.00

K 2 - gang, 1 - way 5A light switch Nr 12 750 9,000.00

L 18A Dimmer switch type MK Nr 6 1,350 8,100.00

M 13A Water heater switch with pilot lamp type MK Nr 16 750 12,000.00

N 2 - gang, 1 - way 5A light switch Nr 4 750 3,000.00

V22: GENERAL LV POWER

Ancillaries; low voltage power socket outlets switches

and contactors as manufactured by MK or ABB or MEM

or approved equal complete with accessories for

P 13A single socket outlet MK Nr 32 1,000 32,000.00

Q 13A Twin socket outlet MK Nr 24 1,550 37,200.00

R 15A socket outlet for Air conditioners MK Nr 20 1,200 24,000.00

S 45A Cooker control unit type MK Nr 4 1,200 4,800.00


20 NOVEMBER 2015


22/29



ELECTRICAL SERVICES (Cont'd)

V21: GENERAL LIGHTING (Cont'd)

Conduit: straight PVC pipe with flange joints in

chases/floor screeds with and including conduit boxes,

locknuts, brushes, couplers, bends, reducers, cuttingand other necessary accessories, rates to include

makin ood surfaces disturbed

A 20mm diametre m 1214 80 97,120.00

B 25mm diametre m 147 85 12,495.00

Y61: HV/LV CABLE AND WIRING

Cables; PVC insulated cables as manufactured by

NOCACO or other approved equal drawn into conduits or

ducts or laid down into trunking or laid in trenchesincluding cable loops, terminations, glands and all other

C 2 x 1.50mm single core PVC copper cable m 2258 125 282,250.00

D 3 x 2.5mm single core PVC copper cable m 655 135 88,425.00

E 3 x 4.0mm single core PVC copper cable m 429 239 102,638.25

F 4 x 25mm2 PVC/PVC cable m 77 3,600 277,200.00

G 4 x 35mm2 PVC/PVC cable m 65 4,550 295,750.00

Y61: HV/LV CABLE AND WIRING

W50: FIRE DETECTION AND ALARM

H 4 x 120mm2 PVC/PVC cable m 80 25,000 2,000,000.00

Equipment

Supply and install fire detection/alarm system as

manufactured by GENT or other approved, complete

with all accessories to form a complete system

Alarm equipment

J Smoke detector Nr 22 4,500 99,000.00

K Heat detector Nr 2 4,500 9,000.00


21 NOVEMBER 2015


23/29



ELECTRICAL SERVICES (Cont'd)

W50: FIRE DETECTION AND ALARM

A 6 Zone Fire Alarm Panel Nr 1 40,000 40,000.00

B Fire Alarm initiating break glass point Nr 4 4,000 16,000.00

C Master Blast Siren Nr 2 8,500 17,000.00

W51: EARTHING AND BONDING

D Earthing of the whole installations at switch boards,

distribution boards etc with 25 x 3 copper tape and 600

x 600mm mat forming a basket and bonded to

foundation reinforcement complete with salt and

charcoal a lied as s ecified

Item 75,000.00

Builders Work

E Allow a provisional sum of N 95,000.00 for builder's

work in connection with all works

Sum 95,000.00


ELECTRICAL SERVICES

COLLECTION

AYB/GA/3BF/20 901,700.00

AYB/GA/3BF/21 469,480.00

AYB/GA/3BF/22 3,263,878.25

AYB/GA/3BF/23 243,000.00

ELEMENT NR. 5A ELECTRICAL SERVICES


22 NOVEMBER 2015


24/29



ELEMENT NR. 5B MECHANICAL SERVICES

Y: MECHANICAL INSTALLATIONS

N: FURNITURE /EQUIPMENT

N13: SANITARY APPLIANCES/FITTINGS

Sanitary appliances/fittings of approved make; including

jointing to galvanised steel water supply and

un lasticised PVC drain i e

APPLIANCE/FITTING

A Sweethome WC complete with Wash hand basin will all

vanity pedestal or Armitage complete with foreign

si hon P-tra

Nr 16 45,900 734,400.00

B Toilet roll holder Nr 16 500 8,000.00

C 450 x 450mm mirror plugged into wall Nr 16 500 8,000.00

D 38mm diametre bottle trap Nr 16 750 12,000.00

E Soap dish Nr 16 1,250 20,000.00

F 50litres capacity electric water heater Nr 12 21,000 252,000.00

R DISPOSAL SYSTEMS

Pipes; straight; UPVC; in ducts, wall, floor screeds:

G 100mm dia M 230 270 62,100.00

H 75mm dia M 225 225 50,625.00

J 50mm dia M 288 135 38,880.00

Pipework ancillaries

K Floor drain, plastic drain coupled with dirt sleeve;

mounted flush with floor finish; 50mm diametre

Nr 16 155 2,480.00


23 NOVEMBER 2015


25/29



R12: DRAINAGE BELOW GROUND

Excavating Trenches

P30: Trenches/Pipeways/Pits For Buried EngineeringServices

A Excavating trenches for services 200mm nominal size;

500mm average depth from 150mm below existing

ground level; backfilling with selected excavated

materials dis osal of sur lus excavated materials

M 450 125 56,250.00

Straight UPVC pipes in ducts/chases/trenches/floor

screeds

B 100mm diametre Nr 300 280 84,000.00

Extra Over UPVC pipes; fittings

Elbow

C 100mm diametre Nr 45 387 17,415.00

D 50mm diametre Nr 30 310 9,300.00

Tee

E 100mm diametre Nr 25 450 11,250.00

F 75mm diametre Nr 20 390 7,800.00

G 50mm diametre Nr 25 235 5,875.00

Y11: Pipework ancillaries

Pipework ancillaries

H Floor drain, plastic drain coupled with dirt sleeve;

mounted flush with floor finish; 50mm diametre

Nr 16 250 4,000.00

J Flexible pan connector; 100mm diametre Nr 16 560 8,960.00

K Ditto 75mm diamtre Nr 16 300 4,800.00


24 NOVEMBER 2015


26/29



R12: DRAINAGE BELOW GROUND (Cont'd)

Inspection chambers; square on plan; in 150mm

blockwork and concrete bed and cover slab;

A Inspection chamber, 600 x 600 x 450mm deep

internall

Nr 10 4,000 40,000.00

B Ditto Manhole Nr 6 4,000 24,000.00

Septic tank; 2 nr. Attached to manholes 450 x 450

x 450mm deep excavations, concrete, formwork,

reinforcement, 230mm blockwork, rendering,

pipework, filling etc..

C 2270 x 1200 x 2000mm deep septic tank Nr 3 350,000 1,050,000.00

Soakaways; comprising excavations, concrete work,

formwork, reinforcement, 230mm blockwork,

rendering, pipework, filling etc..

D 2500 x 2500 x 2000mm deep soakaway pit Nr 3 200,000 600,000.00

S PIPED SUPPLY SYSTEMS

S10 COLD WATER

P30: Trenches/Pipeways/Pits For Buried Engineering

Services

E Excavating trenches for services 200mm nominal size;

500mm average depth from 150mm below existing

ground level; backfilling with selected excavated

materials dis osal of sur lus excavated materials

m 250 125 31,250.00

Pipes; Straight UPVC pipes in ducts/ chases/

Trenches/floor screeds

F 38mm diametre m 97 160 15,520.00

G 25mm diametre m 112 155 17,360.00

H 19mm diametre m 112 155 17 360.00

Extra over pipework; galvanised mild steel

J 25mm dia elbow Nr 22 210 4,620.00

K 19mm dia elbow Nr 22 210 4,620.00

L 25 x 25 x 19mm reducingTee Nr 19 335 6,365.00

M 25 x 19mm reducing elbow Nr 12 290 3,480.00


25 NOVEMBER 2015


27/29



R12: DRAINAGE BELOW GROUND (Cont'd)


A 13mm dia Union Nr 20 430 8,600.00

B Ditto Elbow Nr 14 170 2,380.00

C Ditto Gate valve Nr 20 170 3,400.00

D 13mm dia flexible connector Nr 20 125 2,500.00

E Ditto equal tee 13 x 13 x 13mm Nr 14 250 3,500.00

Pipes; Straight UPVC pipes in ducts/ chases/

Trenches/floor screeds

F 19mm diametre in chases Nr 15 100 1,500.00

G 13mm diametre in chases Nr 23 70 1,610.00


H 25mm diametre union Nr 6 335 2,010.00

J 25mm diametre union 1 210 210.00

K Ditto; unequal tee 25 x 25 x 19mm diametre Nr 2 340 680.00

L 25mm diametre gate valve Nr 3 130 390.00

M 19mm diametre gate valve Nr 5 130 650.00

N 25mm diametre Elbow Nr 1 210 210.00

P 19mm diametre Elbow Nr 6 210 1,260.00

Q 19mm diametre plugs Nr 1 125 125.00

R 19x 19x 19mm diametre Tee Nr 3 290 870.00

Y59: SUNDRIES/COMMON MECHANICAL ITEMS

S Marking position of holes, mortices and chases in the

structure; for the i ed su l s stems installations

Item 80,000.00


26 NOVEMBER 2015


28/29



U VENTILATION/AIRCONDITIONING SYSTEMS

U60 AIRCONDITIONING UNIT

A National/Panasonic split unit cooling capacity 18,000

BTU/hr (1.5 HP)

Nr 20 75,000 1,500,000.00

W50 FIRE DETECTION AND ALARM

Equipment

B 9kg Fire Extinguishers complete with wall bracket Nr 10 15,000 150,000.00


ELEMENT NR. 5B MECHANICAL INSTALLATIONS

Collections

AYB/GA/3BF/24 1,188,485.00

AYB/GA/3BF/25 209,650.00

AYB/GA/3BF/26 1,814,575.00

AYB/GA/3BF/27 109,895.00

AYB/GA/3BF/28 1,650,000.00

ELEMENT NR.5B MECHANICAL INSTALLATIONS

CARRIED TO SUMMARY N 4,972,605.00

SUMMARY


ELEMENT NR. 5A ELECTRICAL SERVICES 4,878,058.25

ELEMENT NR.5B MECHANICAL INSTALLATIONS 4,972,605.00


CARRIED TO SUMMARY N 9,850,663.25

27 NOVEMBER 2015


29/29



GENERAL SUMMARY

GROUP ELEMENT NR. 1 SUBSTRUCTURE 5,167,525.00

GROUP ELEMENT NR.2 SUPERSTRUCTURE 19,384,900.00

GROUP ELEMENT NR.3 FINISHES 7,990,900.00

GROUP ELEMENT NR.4 FITTINGS, FURNISHING

AND EQUIPMENT

600,000.00

GROUP ELEMENT NR. 5 SERVICES 9,850,663.25

CARRIED TO GRAND GENERAL SUMMARY N 42,993,988.25

elemental bill of quantities for 3 bedroom apartment block

Documents