PAGE 1

®

DESIGN WORKSHOP NEW YEAR’S EVE NECKLACE Materials By: Sara Ellis

• 3 1.5 inch Silver Tone Safety Pins• 2 1 inch Silver Tone Safety Pins• 8 Silver Tone Wire Guardians – 325B-002• 8 Silver Tone #1 Crimp Beads – JFC1S-1.5G• 28 5mm Silver Tone Sparkle

Crimp Covers – 349B-023• 6 4mm Silver Tone Jump Rings – 314B-003• 2 6mm Silver Tone Jump Rings – 314B-005• .38mm 49 Strand Silver Color

Stringing Wire – JW10S-10FT• 6 Silver Tone Eye Pins – 310B-113• 22 Gauge Tarnish Resistant Silver

Artistic Wire – AWD-22S-10-08YD• 20 Gauge Tarnish Resistant Silver

Artistic Wire – AWD-20S-10-06YD• 24 Gauge Grey Artistic Wire – AWS-24-21-10YD• 24 Gauge Hematite Artistic Wire

– AWD-245-19-10YD• Black Poly Sparkle Thread – 130U-010• Silver Tone Cameo 6 Clear Crystals

3 Strand Upper Clasp – 303W-2289• 79 6mm Light Grey Glass Pearls• 2 6mm Dark Grey Glass Pearls• 4 8mm Dark Grey Glass Pearls• 2 8mm White Glass Pearls• 3 10mm White Glass Pearls• 79 2mm Silver Tone Spacer Beads• 2 4mm Swarovski Silver Night Bicone Beads• • Tools:• Beadstrom Chain Nose Pliers – 201P-011• Beadstrom Round Nose Pliers – 201P-014• Designer Flush Cutter – 202E-001• Crimper Tool – JTCRIMP1• Mighty Crimper Tool – JTCRIMP3• Tassel Maker – 216S-100• Professional Deluxe Coiling Gizmo – JTPROFWIN

1. Using the instructions included with the Professional Deluxe Coiling Gizmo, coil a 12” section of 24 Gauge Grey Artistic Wire using the smallest mandrel. 2. Using the instructions included with the Conetastic, begin a cone using 20 Gauge Tarnish Resistant Silver Artistic Wire and the largest cone mandrel. 3. After wrapping the wire two or three times, slide the Grey wire coiled section onto the 20 Gauge wire. Slide the coil up against the mandrel and continue wrapping. 4. The finished cone should look similar to image 4. Set aside.

1

34

PAGE 2

5. Repeat Steps 1-4 to create a coiled wire cone with 24 Gauge Hematite Artistic Wire. Set aside. 6. Using the instructions included with the Tassel Maker, create a tassel loop with Black Poly Sparkle Thread. Wrapping approximately 75 times. 7. Remove the tassel loop from the Tassel Maker and cut the loop in half, creating two tassel cord sections. 8. Following the instructions under the “Add Cone to Tassel” section of the Tassel Maker In-structions, thread one of the coiled cones onto the wire. 9. Add a 4mm Swarovski Silver Night bicone to the wire. 10. Following Steps 5 & 6 of the “Add Cone to Tassel” section of the Tassel Maker Instructions, create a wrapped loop on top of the bicone. 11. Using the Designer Beading Scissors, trim the end of the tassel to create the desired shape.

12. Using Chain Nose Pliers, attach a 4mm Jump Ring to the loop on the top of the created tassel.

13. Repeat Steps 6-12 with the second coiled cone to create a second finished tassel. (NY9.jpg) Set both tassels aside.

14. Thread the end of the Stringing Wire through a #1 Crimp Bead, through a Wire Guardian and back through the Crimp Bead.

15. Place the Crimp Bead into the first section of the Crimper Tool and close the Crimper Tool over the Crimp Bead.

16. Move the Crimp Bead into the second section of the Crimper Tool and close the Crimper Tool over the Crimp Bead, creating a “U” shape with the Crimp Bead.

17. Trim the tail of the wire as close to the Crimp Bead as possible with the Flush Cutter.

18. Using the Mighty Crimper Tool, place a Sparkle Crimp Cover over the Crimp Bead.

19. Begin stringing 6mm Light Grey Glass Pearls onto the wire, stringing 2mm Silver Spacer Beads between each pearl.

20. Thread on a total of 15 Light Grey 6mm Glass Pearls.

21. Thread on a 2mm Silver Spacer Bead, a 6mm Dark Grey Glass Pearl , a 2mm Silver Spacer Bead and an 8mm White Glass Pearl to complete the strand. 22. Repeat Steps 14-18 to finish the strand, catching one wire of a 1.5 inch Safety Pin within the Wire Guardian. 23. Repeat Steps 14-18 to begin a second beaded strand. 24. Thread 17 6mm Light Grey Glass Pearls onto the wire, with 2mm Silver Spacer Beads be-tween each one. 25. Thread on a 2mm Silver Spacer Bead, an 8mm Dark Grey Glass Pearl, a 2mm Silver Spacer Bead, and a 10mm White Glass Pearl to complete the strand.

26. Repeat Steps 14-18 to finish the strand, catching one wire (same side) of a 1.5 inch Safety Pin within the Wire Guardian, below the first strand. 27. Using the Mighty Crimper Tool, attach Sparkle Crimp Covers to the Safety Pin Win, above, below and between the two Wire Guardians. (NY16.jpg) To fill up the entire wire, attach one

7

10

11

14

17

22

PAGE 3

above the top Wire Guardian, three between the two Wire Guardians and two below the second Wire Guardian. 28. Repeat Steps 14-18 to begin a new strand. 29. Thread 22 6mm Light Grey Glass Pearls with 2mm Silver Spacer Beads between each pearl. 30. Thread on a 2mm Silver Spacer Bead, a 6mm Dark Grey Glass Pearl, a 2mm Silver Spacer Bead and an 8mm White Glass Pearl to finish the strand. 31. Repeat Steps 14-18 to finish the strand, catching the opposite wire of the 1.5 inch Safety Pin within the Wire Guardian.

32. Repeat Steps 14-18 to begin a new strand. 33. Repeat Step 29. 34. Thread on a 2mm Silver Spacer Bead, an 8mm Dark Grey Pearl, a Silver Spacer Bead and a 10mm White Glass Pearl to finish the strand. 35. Repeat Steps 14-18 to finish the strand, catching the wire of the 1.5 inch Saftey Pin within the Wire Guardian, below the first strand. 36. Repeat Step 27, attaching Sparkle Crimp Covers to that side of the Safety Pin. Set aside. 37. Thread a 6mm Light Grey Glass Pearl onto an eye pin. 38. Using Chain Nose Pliers, bend the wire 90 degrees above the pearl. 39. Using the Flush Cutter, trim the wire, leaving approximately ½” of wire. 40. Using Round Nose Pliers, grasp the end of the wire and roll the wire back towards the pearl, creating a closed loop. Set aside. 41. Repeat Steps 37-40 using 2 more 6mm Light Grey Pearls, 2 8mm Dark Grey Pearls and 1 10mm White Glass Pearl. 42. Using Chain Nose Pliers, opening a loop on a 6mm Light Grey Glass Pearl, thread on an 8mm Dark Grey Pearl. Close the loop. 43. Using Chain Nose Pliers, open a 6mm Jump Ring and thread on the top loop of the Dark Grey Pearl from the previous step. 44. Before closing the Jump Ring, thread the Jump Ring through the hole on the bottom of the Safety Pin. Close the Jump Ring. 45. Using Chain Nose Pliers, open a loop on a 6mm Light Grey Glass Pearl, thread on another 6mm Light Grey Glass Pearl. Close the loop. 46. Using Chain Nose Pliers, open the bottom loop of the Light Grey Glass Pearl added in the previous step, thread on an 8mm Dark Grey Glass Pearl. Close the loop. 47. Using Chain Nose Pliers, open the bottom loop of the Dark Grey Glass Pearl added in the previous step, thread on a 10mm White Glass Pearl. Close the loop. 48. Using Chain Nose Pliers, open a 6mm Jump Ring and thread on the top loop of the first Light Grey Glass Pearl in the linked section. 49. Before Closing the Jump Ring, thread the Jump Ring through the loop on the bottom of the safety pin, next to the previously added link section. Close the Jump Ring.

36

37

39

40

44

47

PAGE 4

50. Using Chain Nose Pliers, open the 4mm Jump Ring at the top of one of the created tassels and thread it onto the bottom ring of the 10mm White Glass Pearl. Close the Jump Ring. 51. Repeat Step 50 with the other created tassel. 52. Link a 1.5 inch Safety Pin and a 1 inch Safety Pin together by threading one through the loop on the bottom of the other. 53. Attach the created Safety Pin triangle to the beaded strands of the necklace on one side of the central Safety Pin. Attach them at an angle, over 2mm Silver Spacer Beads. *This accent can go anywhere you wish on the beaded strands.*

54. Add Sparkle Crimp Covers to the attached Safety Pins using the Mighty Crimper Tool.

55. Repeat Steps 53 & 54 on the opposite side of the necklace. 56. Using Chain Nose Pliers, attach 4mm Jump Ring to the Wire Guardians on the ends of each beaded strand. 57. Before closing the Jump Rings, thread the Jump Rings on the top strands to the top holes of the Cameo Clasp. Close the Jump Rings. 58. Attach the bottom strands to the bottom holes of the Cameo Clasp, leaving the middle hole empty. 59. The finished necklace should look similar to image on first page.

For a Gold Color Necklace:-3 1.5 inch Gold Color Safety Pins-2 1 inch Gold Color Safety Pins-8 Gold Color Wire Guardians – 325A-002-8 Gold Tone #1 Crimp Beads – JFC1G-1.5G-28 5mm Gold Sparkle Crimp Covers – 349A-022-6 4mm Gold Color Jump Rings – 314A-004-2 6mm Gold Color Jump Rings – 314A-006-.30 49 Strand Gold Color Stringing Wire – JW20G-10FT-6 Gold Color Eye Pins – 310A-113-22 Gauge Tarnish Resistant Brass Artistic Wire – AWD-22-NTB-08YD-20 Gauge Tarnish Resistant Brass Artistic Wire – AWD-20-NTB-06YD-24 Gauge Bare Yellow Brass Artistic Wire – AWD-24-BYB-10YD-24 Gauge Tarnish Resistant Brass Artistis Wire – AWD-24-NTB-10YD-Gold Poly Sparkle Thread – 130G-010-Gold Color Cameo 6 Clear Crystals 3 Strand Upper Clasp – 303A-289

50

51

54

58