core catalog
TRANSCRIPT
1-866-433-0027
www.CoreTerminalProducts.com
We are the companywho calls you back!
Pre-Engineered Terminal Products
1-866 -433 -0027
MODEL DESIGNED TONO. WORK WITH
ATX TANK TRUCKS
Portable Truck Access Units
ATX
How it works
• Easily push the unit up to the parked truck you need toaccess.
• Raise the safety cage above the height of the truck. • Position the ATX where the safety cage surrounds the hatch
on the truck. • Secure the position of the ATX by lowering the leveling jacks
on each corner of the base. • Lower the safety cage so the protective bumpers are
supported by the truck.
Now you can safely access the truck - yes, it’s that easy!
Features
• Unique wheel design allows for atighter turning radius and easiermaneuvering to simplify spotting.
• Slip-resistant platform provides a self-cleaning, slip-resistant surface forimproved safety.
• Platform has heavy rubber bumperson contact surface to protectvehicles from damage.
• Tow bar allows easy moving orrepositioning.
Proper setup requires the support of avehicle before climbing.
1
www.CoreTermina lProduc ts . com
Mobile Units in Stock Ready to Ship in Just 5 Days
Model DESIGNED TONo. WORK WITH
AC8-14-TT TANK TRUCKSAC8-14-RR RAIL CARS
AC8-16 HOPPER CARS
Portable Freestanding Truck, Rail & Hopper Car Access Units
AC8
How it works
• Easily push the unit up to the parked truck or rail car you needto access.
• Raise the safety cage above the height of the vehicle. • Position the AC8 where the safety cage surrounds the area
needing to be accessed. • Secure the position of the AC8 by lowering the leveling jacks
on each corner of the base. • Lower the safety cage so the protective bumpers rest on the
vehicle.
Now you can safely access the vehicle - yes, it’s that easy!
Features
• Freestanding design does NOT haveto rest on vehicle for support.
• Unique wheel design allows for atighter turning radius and easiermaneuvering to simplify spotting.
• Serrated decking on platformprovides a self-cleaning, slip-resistantsurface for improved safety.
• Tow bar allows easy moving orrepositioning.
• 500 lb. load capacity.
2
Pre-Engineered Truck & Railcar Access Racks
How it works
• The vehicle drives into a designated area.
• Personnel walk up the stair to a sturdy, solid platform.
• Access ramp is lowered onto the vehicle where asafety cage surrounds the top of the vehicles hatch.
• Personnel can now safely access the top of thevehicle.
Yes, it’s that easy!
Features
• Complies to OSHA regulations.
• Access racks are constructed from galvanized steel.
• Available as single or double-sided units specificallyengineered for accessing rail cars or tank trucks.
PLATFORM SYSTEMSPLATFORM HEIGHT
4’ X 6’ 10’-6”4’ X 6’ 12’-0”
PLATFORM SYSTEMS WITH 1/2 CANOPYPLATFORM HEIGHT
4’ X 6’ 10’-6”4’ X 6’ 12’-0”
PLATFORM SYSTEMS WITH FULL CANOPYPLATFORM HEIGHT
4’ X 6’ 10’-6”4’ X 6’ 12’-0”
Other Sizes Available - Call for Pricing
Pre-Engineered Terminal Products
1-866 -433 -0027
3
4
Flatbed Fall Prevention Platforms
How it works
• The flatbed truck drives between thetwo platforms.
• With the press of a button, theplatforms move together sandwichingthe trailer in the middle.
• Now personnel can safely access theback of the trailer for tarping,sampling, etc., without the fear offalling.
Features
• Available in single or double-sidedsystems.
• Available in tracking or fixed positionmodels.
• Optional canopy available forweather protection.
• Optional swing gates help preventaccidental falls.
Liability Notice
When a truck rolls onto yourbusiness property, you are held
accountable for the safety of theindividuals who load your goodsonto that flatbed, regardless of
for whom he or she works!
Pre-Engineered and Custom Fall Prevention Equipment
www.CoreTermina lProduc ts . com
MODEL GALVANIZED ALUMINUM PAINTEDNO. WIDTH LBS. LBS. STEEL LBS.
AB 103 24” 300 170 279AB 104 24” 332 190 315AB 105 24” 366 200 352AB 106 24” 409 216 389AB 107 24” 480 267 458AB 108 24” 525 292 502
MODEL GALVANIZED ALUMINUM PAINTEDNO. WIDTH LBS. LBS. STEEL LBS.
AB 104 T 24” 349 210 349AB 105 T 24” 407 232 390AB 106 T 24” 428 255 430
Where it is used
• AB-100 Series flat ramp is to be used at loading rackswhere the vehicles to be accessed are of the sameheight and type.
Example - Dry bulk plant loading dry products intohopper cars.
Where it is used
• AB-100T Series flat ramp with an extension is to be usedat rail car loading racks where there is a variation invehicle size but no height.
Example - Asphalt loading terminal who loads rail carof different sizes. The height of the rail car stays thesame but the width changes.
Pre-Engineered Terminal Products
Bridge Bridge with Extension
1-866 -433 -0027
5
6
MODEL GALVANIZED ALUMINUM PAINTEDNO. WIDTH STEPS LBS. LBS. STEEL LBS.
ST 403 24” 3 264 173 251ST 404 24” 4 306 197 290ST 405 24” 5 350 222 330ST 406 24” 6 386 328 370ST 407 24” 7 490 340 466ST 408 24” 8 530 352 506
Where it is used
• ST Series Stair is our most versatile access ramp. Itaccommodates height variations in most tank cars,tank trucks, and hopper cars.
Example - Food processing plant that needs to accessboth rail cars and tank trucks. The ST Series canaccess both vehicles.
Our cages meet OSHA regulations for the requiredfall prevention equipment needed while accessingthe top of trucks and rail cars.
VEHICLEUSED ON DESCRIPTION
Truck 3 Rail Cage - 4’ X 6’Rail car 2 Rail Cage - 4’ X 6’Rail car 2 Rail Cage - 6’ X 6’Rail car 2 Rail Cage - 8’ X 8’
Safety Cages
Truck and Rail Access Gangways
This allows thegangway to movealong the side of theloading platform,allowing virtuallyunlimited access toone or multiplevehicles.
Track Mounting
Stair Features
• Padded lower edge helps prevent vehicledamage.
• Open serrated slip-resistant walk surface maximizesfooting in all climates.
• Requires little maintenance and is repairable in thefield.
• Face mounted as standard; optional top, pivoting,or track mounted available.
• Optional power operated system available -pneumatic, hydraulic, or hand winch.
• Covered by Core Terminal Products' 2 yearwarranty.
www.CoreTermina lProduc ts . com
We carry a wide variety of top and bottom loading arms
From Water & Food Products To Your Most Aggressive Chemicals & Acid Handling, We Offer Arms That Allow You To Easily Handle It!
Core offers the widest variety of loading arm configurations and specifications to meet and exceed the most demandingapplications for loading and unloading rail cars and tank trucks, whether via top loading or bottom loading.
Bottom Loading Arms
Counterweighted Hose Loader
This popular hose loader features a flange-by-flange base swivel
joint for reliable performance and ease of maintenance.
Spring Balanced Hose Loader
Spring balanced hose loaders are available in both short-range
and long-range versions. The short-range model has the torsion
spring mounted back at the riser; while on the long-range units
the spring is located a short distance out on the arm.
Top Loading Arms
The slide sleeve type of arm incorporates a slide sleeve assemblythat telescopes in and out to adjust for variations in the distancefrom the loading rack to the hauling vehicle. It is primarily used insmall bulk plants and terminals for top loading gasoline, fuel oil,or other petroleum products. This durable, dependable, and costeffective loading arm is time tested as a practical method oflocating the drop tube accurately and easily. The slide sleeve isa medium duty unit designed for flow rates up to 15 ft/sec(4.5m/sec). Higher flow rates may tend to push the inner tubeout beyond the loading point.
• Good for applications where the vehicle type varies• Telescoping primary arm• Deadman-type loading valve
Visit our website to build a loading arm to your own specificationsand receive a quote from one of our loading arm advisors
Pre-Engineered Terminal Products
1-866 -433 -0027
7
8
How To Order Core Swivel Joints
1. STYLE: The first step in ordering a swivel joint is to determine
the style you need. The swivel joint industry has developed a
common listing for swivel joint styles, which are determined by
the number of swivels and elbows in the assembly.
2. SIZE: We offers swivel joint that range in size from 2” – 24”.
3. BODY MATERIAL: Our basic offering of swivel joint materials
include Carbon Steel, Stainless Steel, and Aluminum. Should
product or temperature compatibility require a different
material, we are experienced in producing swivel joints in a
variety of exotic materials.
4. INLET CONNECTION: This refers to any connection fitting
attached to the inlet end of the swivel. Basic swivels include
buttweld end connections.
5. OUTLET CONNECTION: Same as above, except for the
outlet connection of the swivel.
6. SEAL MATERIAL: Our basic offering of seal materials
includes Buna, Viton, and PTFE. Should product or temperature
compatibility require it, different materials are available.
7. APPLICATION INFORMATION: Please supply the following
information which will allow us to ensure that the swivel joint
you are ordering is ideal for your specific application.
• Product being handled
• Maximum temperature
• Operating pressure
We offer a wide variety of swivel joints to fit almost any application. In order to assist you in ordering the correct swivel joint, wehave developed a guideline that explains all of the information that we require to specify a swivel joint.
NEW PART NUMBERS! In order to create some uniformity with our swiveljoint part numbers, we have developed a numbering system thatcorresponds with steps 1-7 above. The illustration below shows how tobuild the part number.
S20 S30S40 S50S60 S70S10 S80
S20
02=2” 03=3”04=4” 06=6”
08=8” 10=10”12=12” 16=16”20=20” 24=24”
02
0=CST1=SST
1
01=Buttweld02=150# Flange03=300# Flange04=TTMA Flange05=FNPT06=MNPT
01 01
1=Buna2=Viton3=PTFE
3
S20 S30 S40 S50 S60 S70 S10 S80
We Have Swivel Joints in Stock!
www.CoreTermina lProduc ts . com
Dry DiscountsAvailable
9
Zippered Hose Jackets
Made from weather and sun resistant heavy-dutyNylon with a builtin protective foam core.
Available in multiple colors and comes with yourchoice of colored bands and lettering.
The most economical way to helpprevent contamination to thousands ofdollars’ worth of product from loadinginto the wrong container.
Rail Car Spill Containment
Features
• Available in 10’, 11’, or 12’ widths by 20' or 40’ lengths.
• Pans may be placed end to end for continuouscoverage.
• Pans are manufactured of heavy gauge carbon steel.
Where it is used
• While transferring products, there is always a risk of leakage,OSHA insists you take actions to eliminate environmentalcontamination. Our track pans contain any spills and leaks,helping you meet OSHA regulations.
Pre-Engineered Terminal Products
1-866 -433 -0027
10
Fixed Ladders and Fixed Caged Ladders
We offer a complete line of OSHA compliant fixed ladders and cage ladders. Visit our website or call us for pricing.
SwingGates
SecurityCovers
RestPlatform
Handrailsto Roof
Where it is used
• The perfect solution to reachingareas that require frequent access.Cage ladders require less area andare quicker and safer thanconventional ladders.
Features
• Ladders are available with eitherflared or non-flared top.
• Available in aluminum, steel(galvanized, primed, mill, or painted),and stainless steel to meet specificenvironmental requirements.
• Holdout brackets are standard. Onepair per 10’ on steel ladders; one pairper 6’ on aluminum ladders.
Visit our website www.CoreTerminalProducts.com for complete specifications and pricing
OSHA Compliant Fixed Caged Ladders
www.CoreTermina lProduc ts . com
11
MODEL HEIGHT TO BOTTOM SIZE LBS.PLATFORM
601-02 24” 22” X 30” 24601-03 36” 23” X 37” 31601-04 48” 25” X 45” 38601-05 60” 26” X 52” 45601-06 72” 28” X 60” 62601-07 84” 29” X 67” 68601-08 96” 31” X 75” 78601-09 108” 32” X 82” 86601-10 120” 34” X 90” 103601-11 132” 35” X 97” 119601-12 144” 37” X 105” 135
MODEL HEIGHT TO BOTTOM SIZE LBS.PLATFORM
675-30 30” 24” X 40” 53675-40 40” 25” X 47” 64675-50 50” 26” X 54” 75675-60 60” 27” X 61” 86675-70 70” 29” X 68” 97675-80 80” 30” X 71” 108675-90 90” 31” X 81” 114
675-100 100” 32” X 88” 120675-110 110” 33” X 95” 126675-120 120” 35” X 102” 132675-130 130” 36” X 109” 147675-140 140” 37” X 116” 162
601 Series 300 lbs. Capacity
675 Series 500 lbs. Capacity
Process Workstands
Ladder type workstands afford easy access withina smaller footprint, saving valuable work space.Designed to meet the most demanding industrialaccess requirements.
MODEL HEIGHT TO PLATFORM SIZE BASE SIZE LBS.PLATFORM
720-20 20” 16” X 12” 21” X 24” 12724-24 24” 16” X 12” 22” X 28” 13730-30 30” 16” X 12” 24” X 32” 15736-36 36” 16” X 12” 25” X 36” 16748-48 48” 16” X 12” 27” X 43” 22
MODEL HEIGHT PLATFORM SIZE BASE SIZE LBS875-12 12” 12” X 18” 18” X 24” 6
Features
• Available in aluminum, steel (galvanized, primed, mill, orpainted), and stainless steel.
• Aggressive tread decking for improved slip-resistance inmost weather conditions.
Features
• A large 12" x 16" platformprovides a comfortable worksurface on which to stand forextended periods of time.
• 6" deep slip-resistant steps foradded comfort and safety while climbing andworking.
• Optional Tilt-N-Roll casters for easy repositioning andtransporting.
601 Series 675 Series
Heavy-Duty Aluminum Workstands
Features
• Meets and/orexceeds OSHA andANSI requirements.
• Large 12” x 18”embossed platformfor easy access and added comfort.
• Flared legs provide a wide tip-resistant base.
• Slip-resistant rubber treads attached to heavy-duty aluminum angle feet provide sure footing.
• Industrial Type IA, 300 lb. duty rating.
Rugged Aluminum Workstands
Pre-Engineered Terminal Products
1-866 -433 -0027
12
HEIGHT TO TOTAL PLATFORM BASE MODEL PLATFORM HEIGHT SIZE SIZE LBS901-04 48” 68” 19” X 22” 25” X 51” 35
HEIGHT TO TOTAL PLATFORM BASE MODEL PLATFORM HEIGHT SIZE SIZE LBS
900-03 36” 36” 16” X 12” 19” X 35” 18900-04 48” 48” 16” X 12” 22” X 44” 24
MODEL HEIGHT PLATFORM SIZE BASE SIZE LBS
802-24 24” 16” X 8” 19” X 18” 7
Process Workstands
Features
• Large 8" x 16" embossed platform.
• 4" deep slip-resistant ribbedsteps provide sure footing.
• Each step is braced front andback with 4 gussets and attachedwith16 rivets for added strength and durability.
• Slip-resistant rubber treads attached to heavy-dutyaluminum angle feet provide sure footing.
Rugged Aluminum Workstand
Features
• Large 12" x 16" one-pieceplatform.
• 4" deep slip-resistant ribbedsteps provide sure footing.
• Each step is braced frontand back with 4 gussetsand attached with 16 rivetsfor added strength anddurability.
• Slip-resistant rubber treads attached to heavy-dutyaluminum angle feet provide sure footing.
Double-Sided Non-FoldingAluminum Workstands
Features
• Large 8" x 16" embossedplatform.
• 4" deep slip-resistant ribbedsteps provide sure footing.
• Each step is braced frontand back with 4 gussetsand attached with16 rivetsfor added strength and durability.
• Slip-resistant rubber treads attached to heavy-dutyaluminum angle feet provide sure footing.
• Optional non-folding model available.
Double-Sided Folding Aluminum Workstands
MODEL HEIGHT PLATFORM SIZE BASE SIZE LBS
803-36 36” 16” X 8” 20” X 23” 12
Features
• Can be climbed from eitherside.
• Large 19" x 22" one-pieceembossed platform.
• Spring loaded, weightactivated, 3" casters allowfor easy positioning.
• 4" deep slip-resistant ribbedsteps provide sure footing.
• Each step is braced front and back with 4 gussets andattached with16 rivets for added strength anddurability.
• Slip-resistant rubber treads attached to heavy-dutyaluminum angle feet provide sure footing.
Double-Sided Folding Aluminum Workstands
Quality Workstand Built to Last!
www.CoreTermina lProduc ts . com
Pre-Engineered Terminal Products
Quantity DiscountsAvailable
Any MaterialAny Configuration
Fast Delivery
Where it is used
• Custom fabricated platforms and crossovers are idealfor accessing those hard-to-reach repetitive task areas.
Process Workstands
Features
• OSHA and/or ANSI standards as we interpret them.
• Can be customized to meet your specific needs.
• Available in aluminum, steel (galvanized, primed, mill, orpainted), stainless steel, and corrosion-resistant, non-conductive fiberglass.
• All units come standard with an aggressive treaddecking for improved slip-resistance in most weatherconditions.
• Available fully welded/assembled or knocked down.
1-866 -433 -0027
13
Purchase Order Number: ___________________
Contact Information
Name:______________________________________________________________________ Company:____________________________________________________________
Phone Number:___________________________________________________________ E-mail Address:_____________________________________________________________
Address:_______________________________________________________________________________________________________________________________________
City:_________________________________________________________________________ State:____________________________ Zip:_____________________________________
6 easy steps to the perfect crossover
Step 1. What is the width and height of the item you are crossing? Width __________________________ Height __________________________
Step 2. Are A & B at the same height? � Yes � NoIf no, what is the height difference? ____________________________
Step 3. From the opposite page, which configuration do you require?� A � B � C � D � E � Configuration Sketch Attached
Step 4. What material of construction do you need?� Aluminum � Steel � Mill Finish � Primed � Galvanized � Fiberglass
Step 5. What type of walk surface do you require?� Slip-Resistant � Check Plate
Step 6. Rip out this page and fax it back to 843-673-9903.
Build Your Own Dyke Bridge
www.CoreTermina lProduc ts . com
14
Use any combination of the seven
components to build your
custom platform or crossover.
Pre-Engineered Terminal Products
Multi-Access Component System
Where it is used
• Multi-Access Component Systems can be used tocreate a custom crossover or platform to fitspecifically to your requirements.
You can build almost any size, shape, or configuration!
Features
• Meets OSHA/ANSI requirements
• Aluminum construction - strong, lightweightequipment that saves on freight and allows easyconfiguration.
• Aluminum construction with stainless steel fasteners.
• All platforms are pre-drilled at 30” increments toallow easy configuration.
• Aggressive Alco-Lite® slip-resistant aluminum deckingimproves footing.
• 50 lbs./sq. ft. weight capacity.
Meets OSHA/ANSI
1-866 -433 -0027
15
STAIR RAILINGS
Platform Units (MAPU)
Platform End Supports (MAEU)
Platform Railings (MAPR)
Stair Railings (MASR)
(MASU) Stair Unit 18” to 81” high
(MAEU) Platform End Support 18” to 81” high
(MAPU) Platform Unit 30”, 60”, & 120” lengths
(MAPR) Platform Railing match platform length
(MASR) Stair Railing match stair unit number
Stair Units (MASU)
STAIR UNITS
PLATFORM END SUPPORTS
30” WIDE PLATFORM UNITS
MODEL HEIGHT TO # OF PLATFORM WEIGHT PRICEPLATFORM STEPS CLEARANCE LBS.
MASU-02 18” 2 12 9 $137.00MASU-03 27” 3 21 16 $206.00MASU-04 36” 4 30 24 $263.00MASU-05 45” 5 39 32 $321.00MASU-06 54” 6 48 40 $377.00MASU-07 63” 7 57 48 $441.00MASU-08 72” 8 66 56 $499.00MASU-09 81” 9 75 64 $555.00
MODEL PLATFORM PLATFORM WEIGHT PRICEWIDTH LENGTH LBS.
MAPU-30 30” 30” 35 $302.00MAPU-60 30” 60” 61 $476.00
MAPU-120 30” 120” 114 $784.00
MODEL HEIGHT TO USE WITH WEIGHT PRICEPLATFORM STAIR UNIT LBS.
MAEU-02 18” MASU-02 12 $128.00MAEU-03 27” MASU-03 19 $149.00MAEU-04 36” MASU-04 22 $159.00MAEU-05 45” MASU-05 31 $184.00MAEU-06 54” MASU-06 41 $258.00MAEU-07 63” MASU-07 46 $273.00MAEU-08 72” MASU-08 51 $290.00MAEU-09 81” MASU-09 56 $306.00
MODEL USE WITH WEIGHT PRICESTAIR UNIT LBS.
MASR-02 MASU-02 6 $93.00MASR-03 MASU-03 8 $99.00MASR-04 MASU-04 9 $104.00MASR-05 MASU-05 11 $110.00MASR-06 MASU-06 13 $115.00MASR-07 MASU-07 17 $166.00MASR-08 MASU-08 21 $188.00MASR-09 MASU-09 26 $210.00
MODEL USE WITH WEIGHT PRICEPLATFORM UNIT LBS.
MAPR-30 MAPU-30 14 $134.00MAPR-60 MAPU-60/120 21 $154.00
PLATFORM RAILINGS
MODEL USE WITH WEIGHT PRICEPLATFORM UNIT LBS.
S-ADPT MASU-02 1 $28.00
STAIR ADAPTER
MODEL USE WITH WEIGHT PRICEPLATFORM UNIT LBS.
T-ADPT MASU-02 3 $61.00
T-ADAPTER
T-Adapter(T-ADPT)
S-Adapter(S-ADPT)
(T-ADPT) T-Adapter to attach platform unit to side
of platform in a “T” or “L”
configuration (allows
handrail connections).
(S-ADPT) Stair Adapter to attach stair unit to platform
when using only one handrail.
System Components
Just Follow These Simple Guidelines
1. Each platform must be supported at each end by either an End Unit (MAEU) or Stair Unit (MASU).
2. Splices at platform ends must be supported by an end unit (MAEU).
3. T-adapters (T-ADPT) are required to connect a platform unit to the side of a platform in “T” or “L”
configurations (allows handrail connections).
4. If you desire railing on only one side of a stair unit (MASU), you must use a stair adapter (S-ADPT) as a
spacer to connect stair unit to the platform. (Consult your local codes for railing and safety guidelines.)
5. Do not overload.
6. System shall be attached to the supporting surface.
Build Exactly What You Require!
www.CoreTermina lProduc ts . com
16
Pre-Engineered Terminal Products
MODEL HT OPEN BOTTOM LBS.DEPTH WIDTH
100H-HDC-03 3’ 24” 21” 17100H-HDC-04 4’ 31” 22” 21100H-HDC-05 5’ 37” 23” 26100H-HDC-06 6’ 42” 25” 31100H-HDC-07 7’ 49” 26” 37100H-HDC-08 8’ 55” 28” 41100H-HDC-09 9’ 60” 29” 45100H-HDC-10 10’ 66” 31” 51100H-HDC-11 11’ 73” 32” 55100H-HDC-12 12’ 79” 33” 60
MODEL PLAT. TOTAL OPEN BOTTOM LBS.HT HT DEPTH WIDTH
400H-HDC-03 3’ 5’ 37” 23” 25400H-HDC-04 4’ 6’ 42” 25” 30400H-HDC-05 5’ 7’ 49” 26” 35400H-HDC-06 6’ 8’ 55” 28” 40400H-HDC-07 7’ 9’ 60” 29” 45400H-HDC-08 8’ 10’ 66” 31” 49400H-HDC-09 9’ 11’ 73” 32” 54400H-HDC-10 10’ 12’ 79” 33” 59
MODEL HT OPEN BOTTOM LBS.DEPTH WIDTH
F900H-HDC-04 4’ 38” 22” 23F900H-HDC-05 5’ 45” 23” 28F900H-HDC-06 6’ 53” 25” 34F900H-HDC-07 7’ 60” 26” 39F900H-HDC-08 8’ 68” 28” 45F900H-HDC-09 9’ 75” 29” 51F900H-HDC-10 10’ 82” 31” 57F900H-HDC-11 11’ 90” 32” 63F900H-HDC-12 12’ 97” 33” 70
• Tool holes in top foradded convenience.
Extra Heavy-DutyStepladders
Extra Heavy-Duty Platform Ladders
Extra Heavy-DutyDouble-Fronted
Stepladders
• Tool holes in top foradded convenience.
• Large 14" x 17" embossedplatform helps provide acomfortable, slip-resistantwork surface on which tostand.
StandardFeatures
Exceeds OSHA
requirements.
Manufactured of
marine grade
aluminum alloy for
maximum strength.
4" deep slip-resistant
ribbed steps for a
more comfortable
work surface.
Large 1-1/2" wide
aluminum angle feet
with thick rubber
tread.
All components are
field repairable
which increases
ladder life cycle and
reduces costs.
MODEL HEIGHT OPEN BOTTOM LBS.DEPTH WIDTH
F900H-03 3’ 31” 21” 18F900H-04 4’ 38” 22” 23F900H-05 5’ 45” 23” 28F900H-06 6’ 53” 25” 34F900H-07 7’ 60” 26” 39F900H-08 8’ 68” 28” 45F900H-09 9’ 75” 29” 51F900H-10 10’ 82” 31” 57F900H-11 11’ 90” 32” 63F900H-12 12’ 97” 33” 70F900H-13 13’ 105” 35” 74F900H-14 14’ 112” 36” 79F900H-15 15’ 120” 38” 84F900H-16 16’ 127” 39” 89
MODEL PLAT. TOTAL OPEN BOTTOM LBS.HT HT DEPTH WIDTH
400H-02 2’ 4’ 31” 22” 20400H-03 3’ 5’ 37” 23” 24400H-04 4’ 6’ 42” 25” 29400H-05 5’ 7’ 49” 26” 34400H-06 6’ 8’ 55” 28” 38400H-07 7’ 9’ 60” 29” 43400H-08 8’ 10’ 66” 31” 47400H-09 9’ 11’ 73” 32” 51400H-10 10’ 12’ 79” 33” 56400H-11 11’ 13’ 82” 35” 64400H-12 12’ 14’ 89” 36” 71400H-13 13’ 15’ 94” 38” 82400H-14 14’ 16’ 99” 39” 83400H-15 15’ 17’ 105” 41” 88400H-16 16’ 18’ 111” 42” 95400H-17 17’ 19’ 117” 44” 100400H-18 18’ 20’ 122” 45” 107
MODEL HEIGHT OPEN BOTTOM LBS.DEPTH WIDTH
100H-03 3’ 24” 21” 16100H-04 4’ 31” 22” 20100H-05 5’ 37” 23” 25100H-06 6’ 42” 25” 29100H-07 7’ 49” 26” 34100H-08 8’ 55” 28” 38100H-09 9’ 60” 29” 42100H-10 10’ 66” 31” 47100H-11 11’ 73” 32” 51100H-12 12’ 79” 33” 56100H-13 13’ 82” 35” 60100H-14 14’ 89” 36” 65100H-15 15’ 94” 38” 70100H-16 16’ 99” 39” 75100H-17 17’ 108” 41” 86100H-18 18’ 111” 42” 92100H-19 19’ 117” 44” 96100H-20 20’ 122” 45” 101
500 lbs. Capacity
300 lbs. Capacity
Also available in
Fiberglass
1-866 -433 -0027
17
MODEL UNEXTENDED EXTENDED WIDTH LBS
IND-A-020-16 8’ 5” 13’ 5” 22 1/4” 58IND-A-020-20 10’ 5” 17’ 5” 22 1/4” 70IND-A-020-24 12’ 5” 21’ 5” 22 1/4” 92IND-A-020-28 14’ 5” 25’ 5” 22 1/4” 105IND-A-020-32 16’ 5” 29’ 5” 22 1/4” 120IND-A-020-36 18’ 5” 33’ 5” 22 1/4” 128IND-A-020-40 20’ 5” 37’ 5” 22 1/4” 144
MODEL LENGTH WIDTH LBS
IND-A-010-08 8’ 19 1/16” 22IND-A-010-10 10’ 19 1/16” 28IND-A-010-12 12’ 19 1/16” 34IND-A-010-14 14’ 19 1/16” 41IND-A-010-16 16’ 19 1/16” 47IND-A-010-18 18’ 19 1/16” 53IND-A-010-20 20’ 19 1/16” 60
IND-A Single Aluminum Ladders
• Certified and tested to a 500 lb. load capacity.• Manufactured of marine grade aluminum alloy for maximum
strength.• Truss style side rails improve rigidity and reduce rocking.• 11/4” O.D. slip-resistant serrated aluminum rungs.• Bottom rung and side rail gussets reduce rocking and
increase rail support at foot assembly for added durability. • Large aluminum swivel safety shoes with thick rubber treads
may be used in either tread or spike down position forimproved traction in many environments.
• All components are field repairable which increases ladderlife cycle and reduces costs.
IND-A Aluminum Extension Ladders
• Certified and tested to a 500 lb. load capacity.• Manufactured of marine grade aluminum alloy for maximum
strength.• Truss style side rails improve rigidity and reduce rocking.• 11/4” O.D. slip-resistant serrated aluminum rungs.• Bottom rung and side rail gussets reduce rocking and
increase rail support at foot assembly for added durability.• Oversized 21/4” pulley and 1/2” poly rope allow for easy
operation.• Large aluminum swivel safety shoes with thick rubber treads
may be used in either tread or spike down position forimproved traction in many environments.
• All components are field repairable which increases ladderlife cycle and reduces costs.
Equipment for Demanding Applications
www.CoreTermina lProduc ts . com
Also available in
Fiberglass
18
19
Rope Handrails Aluminum Handrails
MODEL LENGTH WIDTH PRICE MODEL LENGTH WIDTH PRICE
SGW-08 8’ 24” $1,648 SGW-08-1 8’ 24” $1,832SGW-12 12’ 24” $1,814 SGW-12-1 12’ 24” $2,084SGW-16 16’ 24” $2,069 SGW-16-1 16’ 24” $2,438SGW-18 18’ 24” $2,120 SGW-18-1 18’ 24” $2,598SGW-20 20’ 24” $2,333 SGW-20-1 20’ 24” $2,793SGW-24 24’ 24” $2,608 SGW-24-1 24’ 24” $3,160SGW-28 28’ 24” $3,114 SGW-28-1 28’ 24” $3,762SGW-30 30’ 24” $3,326 SGW-30-1 30’ 24” $4,018SGW-32 32’ 24” $3,498 SGW-32-1 32’ 24” $4,236SGW-36 36’ 24” $3,921 SGW-36-1 36’ 24” $4,752SGW-40 40’ 24” $4,364 SGW-40-1 40’ 24” $5,285
SG Marine Gangways
• Alco-Lite's heavy-duty marine gangways are designedand manufactured to meet the most demandingapplications.
SGT
• Alco-Lite's marine gangways are designed and manufactured to meet the most demanding application.
Features
• Distributed load capacity of 750 lbs.
• Available in lengths from 12’ to 40’.
• Economical, lightweight, and portable.
• Available in 24” or 28” wide perforated deckwalking surface with angle cleats for bettertraction and added safety.
Features
• Constructed of 6000 series marine grade aluminum alloyfor durability.
• 2000 lbs. distributed load capacity.
• 24” wide aluminum deck plate features a slip-resistantcoating and aluminum angle cleats for better tractionand added safety. Curved tread models available.
• Available with 5-1/2” rollers on dock side, allowing forvariations in ship’s float.
Marine Gangways
Features
• Bowed truss construction affords a distributed loadcapacity of 2000 lbs.
• Available in lengths from 20’ to 40’.
• Constructed of 6000 series marine grade aluminumalloy for durability.
• 24” wide aluminum deck plate features a slip-resistantcoating and aluminum angle cleats for better tractionand added safety.
SGB
• Alco-Lite's super-heavyduty marine gangways aredesigned and manufactured tomeet the most demanding applications.
Pre-Engineered Terminal Products
Also available in 28” widths
1-866 -433 -0027
20
MODEL LENGTH WIDTH LBS.MBL-06 6’ 191/16” 17MBL-08 8’ 191/16” 23MBL-10 10’ 191/16” 29MBL-12 12’ 191/16” 35MBL-14 14’ 191/16” 40MBL-16 16’ 191/16” 46MBL-18 18’ 191/16” 52MBL-20 20’ 191/16” 58MBL-22 22’ 191/16” 63MBL-24 24’ 221/4” 69MBL-26 26’ 221/4” 75MBL-28 28’ 221/4” 81MBL-30 30’ 221/4” 86
MODEL LENGTH WIDTH LBS.DMBL-06 6’ 181/2” 21DMBL-08 8’ 181/2” 28DMBL-10 10’ 181/2” 35DMBL-12 12’ 181/2” 42DMBL-14 14’ 181/2” 49DMBL-16 16’ 181/2” 56 DMBL-18 18’ 181/2” 63DMBL-20 20’ 181/2” 70DMBL-22 22’ 181/2” 77DMBL-24 24’ 237/8” 84DMBL-26 26’ 237/8” 91DMBL-28 28’ 237/8” 98DMBL-30 30’ 237/8” 105DMBL-32 32’ 237/8” 112DMBL-34 34’ 237/8” 119DMBL-36 36’ 237/8” 126DMBL-38 38’ 237/8” 133DMBL-40 40’ 237/8” 140
Features
• Available as a single rung model (MBL) ordouble rung model (DMBL - as shown) withor without handrails.
• All-aluminum construction is lightweight andresists corrosion.
• 11/2” O.D. serrated rungs reduce slippagehazards.
• Open truss construction reduces weight andwind resistance.
• Heavy-duty swivel safety shoes with thickrubber tread improve footing on manysurfaces.
• Heavy-duty 11/2” aluminum Tee extrusion railconstruction for greater strength and rigidity.
• Handrail models - handrails start 4’ from thebottom of the ladder.
MBL & DMBL Marine Ladders
• Designed for the most demanding marineaccess applications.
Marine Ladders
Barge Access Equipment
Barge Access
• Fully adjustable manualand automated shipand barge access unitsare custom designed tofit existing docks andjetties, allowing safeaccess to ship andbarge decks at anyposition and water level.
Equipment for Demanding Applications
www.CoreTermina lProduc ts . com
21
BOTTOMMODEL HEIGHT WIDTH DEPTH PLATFORM WEIGHTAML-03 3’ 25” 42” 20” x 20” 40 lbs.AML-04 4’ 26” 50” 20” x 20” 50 lbs.AML-05 5’ 27” 57” 20” x 20” 57 lbs.AML-06 6’ 29” 65” 20” x 20” 64 lbs.AML-07 7’ 30” 72” 20” x 20” 72 lbs.AML-08 8’ 32” 79” 20” x 20” 77 lbs.AML-09 9’ 33” 87” 20” x 20” 80 lbs.AML-10 10’ 35” 94” 20” x 20” 87 lbs.AML-11 11’ 36” 102” 20” x 20” 93 lbs.AML-12 12’ 39” 109” 20” x 20” 101 lbs.AML-14 14’ 44” 124” 20” x 20” 120 lbs.AML-16 15’ 47” 139” 20” x 20” 138 lbs.
Aviation Maintenance Platforms
AML Series
• The AML is the standard by whichground service ladders arejudged. Selected by most majormanufacturers and commercialcarriers for their quality anddurability.
Features
• Meets or exceeds all applicable OSHAand/or ANSI standards.
• 11/2” angle feet standard.• Primarily 6061-T6 marine grade alloy
construction.• 20” x 20” ribbed extra-sturdy work platform.• 5” rigid Tilt-n-Roll casters standard.• Optional towing feature available.• 1” square aluminum tubing handrail
available.
910H Series
• Double-Fronted AluminumStepladders are designed foraccess from either side or for useby two people at one time.The 910-H is the perfect solutionfor heavy maintenanceapplications.
BOTTOMMODEL HEIGHT WIDTH DEPTH WEIGHT
900HAIR-03 3’ 21” 31” 20 lbs.900HAIR-04 4’ 22” 38” 25 lbs.900HAIR-05 5’ 23” 45” 30 lbs.900HAIR-06 6’ 25” 53” 36 lbs.900HAIR-07 7’ 26” 60” 41 lbs.900HAIR-08 8’ 28” 68” 47 lbs.900HAIR-09 9’ 29” 75” 53 lbs.900HAIR-10 10’ 31” 82” 59 lbs.900HAIR-11 11’ 32” 90” 65 lbs.900HAIR-12 12’ 33” 97” 72 lbs.900HAIR-13 13’ 35” 105” 76 lbs.900HAIR-14 14’ 36” 112” 81 lbs.900HAIR-15 15’ 38” 120” 86 lbs.900HAIR-16 16’ 39” 127” 91 lbs.
Features
• Meets/exceeds OSHA and ANSI standardA14.2 requirements for Type 1-A, 300 lb.duty rating.
• Double-fronted to allow use on either side.• Constructed primarily of 6061-T6 marine
grade alloy.• 11/4” angle feet with heavy-duty skid
resistance pad.• Tool holes in cap for added
convenience.• All parts replaceable; ladder
can be repaired at yourfacility.
• 5” Tilt-n-Roll casters.
Pre-Engineered Terminal Products
1-866 -433 -0027
22MODEL HEIGHT WIDTH WEIGHT
DI-08 8’ 28” 48 lbs.
Aviation Maintenance Ladders
DI-08 De-Icing Ladder
• Designed to meet FAR 121.629 papa. C, foroperation in de-icing conditions
Designed to facilitate the visual check forwing icing on the MD Super 80 series.Lightweight, yet rugged, the DI-80 ladderprovides fast, dependable access for yourinspection process.
Features
• Heavy-duty rubber bumper pads arecurved to rest on wing.
• Aluminum construction.
• Swivel safety shoes.
• Handle for easy carrying.
• 8’ height - to match up to MD-80 wing.
• Different sizes available to match othermodels of aircraft.
ABL Aviation Ladder
• This rigid, one-piece ladder is custom designed to easily fit intoavionics hatch openings of all Airbus-manufactured aircraft, allowingquick and effortless entry and exit into this vital space. Its 8' heightalso makes it ideal for other maintenance and access applicationssuch as engine inlet inspections on Boeing 727 S-Duct and blades oreasy entry into the 727's cargo bay.
Features
• Meets/exceeds ANSI and OSHA standards.
• All-aluminum, channel rail construction for strength, durability andlight weight.
• Thick rubber bumpers to protect fuselageand hatch from scratches.
• 11/4" slip-resistant rungs.
• Swivel type shoes.
• 300 lb. duty rating.
• Field repairable.
Aviation Ground Support Equipment
www.CoreTermina lProduc ts . com
Pre-Engineered Terminal Products
We offer Fall Prevention Equipment designed specificallyfor the type of vehicle you need to access.
See Page 3 See Page 4
See Page 3 See Page 2
1-866-433-0027 www.CoreTerminalProducts.com