cl05 (may 2012)

7/28/2019 CL05 (MAY 2012)

1/67

PROJECT: Infrastructure buildings of the residential complex (phase 2)

of ITCC complex - RIYADH

REVISED BOQ FOR PARKING CLUSTERS (CL05)

AMOUNT

SR

Soil investigation

The contractor shall implemented of exploratory drilling and Notemechanical test in all types of soil with on site testing and theissuance of the final report which contain the test results andrecommendations of the foundation work.

01 Research and treatment for cavities

Implementation through a perforating exploratory(cavity probing) In 1 M3

all types of rock to determined the horizontal and vertical elongation

of cavities, the contractor will be responsible for treatment all

cavities By injection and treatment for all cavities and voids of rock

with all necessary work accordance with the technical

specifications and instructions of the Supervising engineer

SITE DEVELOPMENT

Earthworks, concrete works, water proofing, moisture Note

protection for foundations works are measured in BOQ AP06

The bidder is advised to visit the site before quoting the rates in

order to get himself familiarized with the present site conditions

Site clearance and demolitions

02 Demolish and clear away existing structures, pavings, electrical 1 Item

lighting, pavements or upstands, cut and plug or reroute existing

service lines or utilities inside property line, clear site of rubbish orany impediments, loose top soil and as deemed necessary, for the

total site cluster number 5 (CL05) area, approximately (23230m2),

subject to engineer approval and as coordinated with public

pension agency as shown on drawing CL05- XC-01

To Collection SR

RATEITEM D E S C R I P T I O N QTY UNIT

Project No. J10-13300

ZUHAIR FAYEZ PARTNERSHIP

1 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

2/67




AMOUNT

SRRATEITEM D E S C R I P T I O N QTY UNIT

SITE GRADING

Bulk excavate over site on unclassified ground including all hard Noteand rock layers to reduced levels generally in cutting profiles the

work shall include clear away to approved disposals.

All additional excavation required for temporary works and spaces, Note

shoring, dewatering, removal of surplus excavated materials,

support, temporary spoil heaps and general compaction

EXCAVATION AND EARTHWORK

Necessary moving or transportation about the site excavation

material including handling to temporary stockpile or ultimate

disposal off site is to be included in the unit rate of excavation

SITE PREPARATION AND GRADING

01 Excavation oversite on unclassified ground including all hard and 50 M3

rock layers (if any) to reduced levels generally in cutting profiles

and forming depressions, falls and the like and clear away to

approved disposal tip.

02 Fill oversite with approved imported fill material according to site 11000 M3

soil report recommendation including compaction in making up

levels to required formations, embankments, contouring and the

like as per drawings and spec.

Note

Work on proposed structural built-up areas from part of the Work

pertaining to respective building or structure as measured

elsewhere.

To Collection SR



2 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

3/67




AMOUNT


PAVING AND SURFACING

01 Supply and install precast concrete shotblasted pavers (beige 3438 M2

color) size 400x400x60mm thk.with photocatalytic titanium doxide

coating including 100mm thick cast-in-place concrete slab with

A193-WWF mesh reinforcement, 20mm thick cement mortar

setting bed, moisture barrier on compacted subgrade, 3mm water

proofing membrane on R.C. slab as per detail no A1 on drawing

CL05-XL301 to suit required locations as shown on drawing

CL05-XL101

02 Supply and install precast concrete shotblasted pavers (beige, & 64 M2

brown color) size 400x400x60mm thk.with photocatalytic titanium

doxide coating including 100mm thick cast-in-place concrete slab

with A193-WWF mesh reinforcement, 20mm thick cement mortarsetting bed, polyethylene moisture barrier, compacted subgrade,

3mm water proofing membrane on R.C. slab as per detail no. A5

on drawing CL05-XL301 to suit required locations as shown on

drawin CL02-XL101

03 Supply and install precast concrete shotblasted pavers (light grey 1749 M2

& grey color) size 400x400x60mm thk.with photocatalytic titanium

doxide coating including 100mm thick cast-in-place concrete slab

with A193-WWF mesh reinforcement, 20mm thick cement mortar

setting bed, polyethylene moisture barrier, compacted subgrade,

3mm water proofing membrane on R.C. slab as per detail no. A6


drawing CL05-XL101

04 Supply and install precast concrete shotblasted pavers (beige & 649 M2

light beige color) size 400x400x60mm thk w./grey color granite

band size 200x200x30mm thk including 100mm thick cast-in-place

concrete slab with A193-WWF mesh reinforcement, 20mm thick

cement mortar setting bed, polyethylene moisture barrier,

compacted subgrade, 3mm water proofing membrane on R.C. slab

as per detail no. B3 on drawing CL05-XL301 to suit required

locations as shown on drawing CL05-XL101

05 Supply and install polished granite paving dark &light colors,size 380 M2

400x400x30mm thk w.\ granite band dark color, size200x200x30mm including 100mm thick cast-in-place concrete slab

with A193-WWF mesh reinforcement, 20mm thick cement mortar

setting bed, polyethylene moisture barrier, compacted subgrade,

3mm water proofing membrane as per detail no. C2


drawing CL05-XL101

To Collection SR



3 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

4/67




AMOUNT


PAVING AND SURFACING

01 Supply and install concrete screed with epoxy coat finish including 12690 M2

100mm/50mm thick cast-in-place concrete slab with A193-WWF

reinforcement mesh, polyethylene moisture barrier, compacted sub

grade, 3mm water proofing membrane on R.C. slab as per detail

no. D on drawing CL05-XL301 to suit required locations as shown

on drawing CL05-XL101

02 Supply and install 50mm thk rubber pavement green, blue , brown 120 M2

& red color including adhesive mixture,100mm thick cast-in-place

concrete slab with A193-WWF mesh reinforcement smooth finish,

polyethylene moisture barrier, compacted subgrade, 3mm water

proofing membrane on R.C. slab as per detail no. E4 on drawing

CL05-XL301 to suit required locations as shown on drawingCL05-XL101

03 Supply and install 80mm thick ( beige & grey) color, interlocking 1507 M2

concrete pavers including 20mm thik cement ,mortar setting bed,

compacted sand leveling course , compacted aggregate base

course 150mm thick, cast in place concrete foundation, concrete

edger compacted subgrade complete as per detail F8 on drawing

CL05-XL301 to suit required locations as shown on drawing

CL05-XL101

04 Supply and install cast in place concrete paving with A193-WWF 22 M2

mesh reinforcement, smooth finish light grey color, 100mm thick

w.\ brick edge band size 200x200x60mm thick including 20mm

thick cement mortar setting bed, polyethylene moisture barrier,

compacted subgrade, 3mm water proofing membrane on R.C. slab

as per detail no. G7 on drawing CL05-XL301 to suit required

locations as shown on drawing CL05-XL101

EARTH MOUNT

05 Supply and formation of 500-1500 mm height earth mount including

compacted sub base layer, 100 mmm thick layer of sand and

gravel mix, and all required to complete and finish te work as

shown on drawing CL05- XL101, and as per detail no. 5 on drawing

CL05- XL302 and sections details 166 M2

(Softscape and planting soil mix are measured elsewhere)(area

measured on plan)

To Collection SR



4 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

5/67




AMOUNT


CURBS AND EDGING

01 Supply and install precast concrete road curb, size 300X500X150 2728 Mmm with exposed aggregate finish including bedding, haunching,

cast in place concrete base and concrete grout behind curb, 20mm

thick cement mortar setting bed, on R.C. slab as per detail no.1 on

drawing CL05-XL302 to suit required locations as shown on

drawing CL05-XL101

02 Supply and install precast concrete mowing edge, size 28 M

200X100X65 mm including concrete base, 20mm thick cement

mortar setting bed, cast in place concrete base on R.C. slab, as

per detail no. 2 on drawing CL05-XL302 to suit required locations

as shown on drawing CL05-XL101

SUNDRIES

TENSILE STRUCTURE

03 Supply and install tensile staructure comprising columns, tent

fabric, foundation, earthwork, and all required to compleet and fix

the work as shown on drawing CL05- XL101 and as per detail no. 3

on drawing CL05- XL302, and section details and as per

manufacturer's recommendations and subject to engineer's

approoval to cover an area of 80 m2 . Contractor shall submitt shop

drawings for approval before supply 1 No.

Wooden Shade Structure

04 Supply and install wooden shade staructure comprising 200200mm

artificial wooden post, 100200 mm wooden beams , foundation,

earthwork, and all required to compleet and fix the work as per

deatail 6 on drawing XL302 and manufacturer's recommendations

and subject to engineer's approoval to cover an area of 90 m2 . 1 No.

Contractor shall submitt shop drawings for approval before supply

Wooden Bench

05 Supply and install wooden bench comprising concrete walls,reinforced concrete slab with A 193 W.W.F reinforcement mesh

smooth finished including footings, waterproofing membrane, joint

filler, 50x75 mm interior wooden rails, including earthworks,

insulation, finishing, fixing, and all required to complete the work

as per detail no.4 on drawing CL5- XL302 30 M2

To Collection SR



5 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

6/67




AMOUNT


Manufacturer's standard outdoor sings, letters and plaques

including fixings, finishes, accessories complete as per

details on drawing CL05-XL601,602 and as per specifications

01 Ref. type 1 ( RESIDENTIAL SIGN ) 6 No.

02 Ref. type 2 ( DIRECTIONAL SIGN ) 4 No.

03 Ref. type 3 ( CENTRAL PLAZZA SIGN ) 1 No.

04 Ref. type 4 ( ADVERTISING PANEL ) 2 No.

Manufacturer's standard outdoor sings, letters and plaques

including fixings, finishes, accessories complete as perdetails on drawing CL05-XC-05, CL05-XC-06 and as per

specifications

INFORMATIVE SIGNS

05 Ref. type I-1 ( PARKING ) 3 No.

06 Ref. type I-2 ( ENTRY ) 6 No.

REGULATORY SIGNS

07 Ref. type R2-1 (GIVE WAY ) 9 No.

08 Ref. type R5-1 ( ENTRY PROHIBTED ) 11 No.

09 Ref. type R 8-1 ( NO LEFT TURN ) 2 No.

10 Ref. type R 17-6 (MANDATORY MOVEMENT - L ) 1 No.

WARNING SIGNS

11 Ref. type W11-1 ( PEDESTRAIN CROSSING ) 17 No.

To Collection SR



6 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

7/67




AMOUNT


ROAD SIGNAGE & PAVEMENTMARKING

Thermoplastic paint for traffic marking on drive way atbasement/ground floor and ramps floor as per

Manufacturer's standard as shown on details on drawing

CL05-XC-06, to suit required locations as shown on drawing

CL02-XC-05, as per specification and as per engineer's

instructions

pavement marking

01 Straight arrows 42 No.

02 Straight & curved arrows 5 No.

03 Curved arrows 11 No.

04 Handicapped marking on floor 3 No.

05 Parking lane marking 2170 M

06 White stop line 70 M

07 Pedestrain crossing 122 M

08 Lane marking 910 M

09 White edge line 810 M

10 Dotted ( give way line ) 1010 M

11 Speed control hump including cut & removal of existing wearing 25 M

(0.05m) course & add a new course, tack coat and 0.10m of

bituminous wearing course, ref. 10 detail G

To Collection SR



7 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

8/67




AMOUNT


LANDSCAPING

Trees including pit excavation, stakes and ties, soilplanting mix, mulching, filter membrane and drainage

layer all as details and planting schedule as per detail

P1 on drawing CL05-XL-401

01 T/Af 16 No.

02 T/Fm 32 No.

03 T/Po 2 No.

Shrubs including planting, site excavation as required, soilplanting mix, mulching, filter membrane, screed sloped to

drain and drainage layer all as per details and planting

schedule as per detail P3 on drawing CL05-XL-401

04 S/Hs 107 No.

05 S/Mc 78 No.

06 S/Pav 18 No.

To Collection SR



8 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

9/67




AMOUNT


LANDSCAPING

Ground cover including planting, site excavation asrequired, soil planting mix, mulching, filter membrane,

screed sloped to drain and drainage layer all as per details

and planting schedule as per detail P2, on drawing

CL05-XL-401

01 G/As 1509 No.

02 G/Ggp 1725 No.

03 G/Gr (Y) 493 No.

04 G/Cm (W) 565 No.

Lawn planting, including soil planting mix, filter membrane

and drainage layer, screed sloped to drain all as per details

and planting schedule as per detail P3 on drawing

CL05-XL-401

05 L/Cd 487 M2

To Collection SR



9 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

10/67




AMOUNT


PLUMBING INSTALLATION

WASTE AND DRAINAGE INSTALLATION

Supply, install and testing pipework, UPVC schedule 40, the

work shall include but not limited to fittings, supports, cast

iron pipes on roof for vent with caps, installation, all

associate works and all materials and equipments required

to complete and finish the work according to drawings,

specification and code of practices

01 100 mm dia. 60 M

02 150 mm dia. 315 M

03 200 mm dia. 90 M

Construction work for briks inspection chamber, the work

shall include bit not limited to earth work, plain concrete

for foundation BED, concrete channel at chamber DED with

standard cast iron manhole frame and double cover and all

materials and equipments required to complete and finish

the work according to specifications, drawings and code of

practice

04 Inspection chamber, ref. (IC) 600x600mm 4 No

05 Inspection chamber, ref. (STIC) 600x600mm 6 No


Supply, installation and test drainage pipe work UPVC

schedule 80 the work shall include but not limited to fittings,

supports hangers, excavation, backfilling, cast iron pipes on

roof for vent with caps and all materials and equipment

required to complete and finish the work according to

specifiactions, drawings and code of practice

06 100 mm dia 50 M

Construction work for briks inspection chamber, the work shall

include bit not limited to earth work, plain concrete for

foundation BED, concrete channel at chamber DED with

standard cast iron manhole frame and double cover, UPVCpipework schedule 40 to nearest main sewer manhole and all

materials and equipments required to complete and finish the

work according to specifications, drawings and code of practice

07 Slow down chamber 5 No

To Collection SR



10 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

11/67




AMOUNT



Reinforced concrete under ground water tank and pumproom with required capacity proprietary cast iron manhole

covers and frames, including (concrete work & earthwork,

water proofing) internal lining access ladders, pipework

submersible pump, ventilating fans with exhaust and fresh

air pipework, valves, vent pipes and truck fill pipework as

detailed on drawings

01 Fire Water tank 1 No.

MANHOLE AND COVERS

Supply , install, testing and commissioning precast

concrete sewer manholes with standard traffic (heavy duty)

type cast iron manhole covers and frames, access ladders,concrete channel at manhole bed, foundation bed, drop

pipe to manhole where required, all associated earthworks,

damp proofing, and all materals, equipments required to

complete and finish. the work according to specifications

section 02605, 02730, drawings and code of practices

02 Sewer manhole, ref. (MH) 6 No.

03 Sewer manhole, ref. (STMH) 3 No.

Fire WATER INSTALLATION

Supply, install and testing pipework, UPVC Schedule 80 forfire water the work shall include but not limited to

fittings, supports, all associate works and all materials and

equipments required to complete and finish the work

according to drawings, specification and code of practices

04 100 mm dia. 105 M

Supply, installation and test horizontal split case centrifugal

fire pump, including piping network and valving within pump

chamber,complete with all controllers, accessories for

automatic operateion and all associate workks as per code

standard and as scheduled on drawings and specification

05 Ref. FP1 CAP 75 KW electrically driven 1 No

06 Ref. FP2 CAP 75 KW fuel diesel driven 1 No

To Collection SR



11 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

12/67




AMOUNT


FIRE WATER UTILITIES

Supply, installation and test Electrically driven peripheralturbine Jockey pump, including piping network and valving

within pump chamber, complete with all controllers,

accessories for automatic operateion and all associate

workks as per code standard and as scheduled on drawings

and specification

01 Ref. JP CAP 5 KW 1 No

IRRIGATION WATER INSTALLATION

Supply, install and testing pipework, UPVC Schedule 80 for

Irrigataion water the work shall include but not limited to

fittings, supports, all associate works and all materials andequipments required to complete and finish the work

according to drawings, specification and code of practices

02 20 mm dia. 33 M

03 25 mm dia. 110 M

04 32 mm dia. 30 M

05 50 mm dia. 295 M

Accessories

06 Supply and installation irrigation controller as detailed on drwings 1 No.

and as per specifications

07 Supply and install bubbler for shrubs, ground cover and 770 No.

succulents

08 Supply and installation bubbler for trees 135 No.

09 Supply and installation spray lawn sprinkler 16 No.

10 Gate valve W/valve box 25 mm dia., 1 No.



To Collection SR



12 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

13/67




AMOUNT


Supply and installation remote control valve assembly

including piping complete with valve box, Y-strainer,

accessories and all associated works as detail on drawingand as per specifications section 02810

01 Ref. RCV 20 mm dia. 1 No.



04 Ref. RCV 50mm dia. 6 No.

To Collection SR



13 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

14/67




AMOUNT


SITE DEVELOPMENT

Collection

Sheet -1

Sheet -2

Sheet -3

Sheet -4

Sheet -5

Sheet -6

Sheet -7

Sheet -8

Sheet -9

Sheet -10

Sheet -11

Sheet -12

Sheet -13

To Bill Summary SR



14 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

15/67




AMOUNT


DIVISION 2 - SITE WORK

SITE GRADING

All additional excavation required for temporary works and

spaces, shoring, dewatering, removal of surplus excavated

materials, support, temporary spoil heaps and general Note

compaction

EXCAVATION AND EARTHWORK

Necessary moving or transportation about the site excavation Note

material including handling to temporary stockpile or ultimate

disposal off site is to be included in the unit rate of excavation

Excavation in natural land consisting of solid rock

formation, cracked rocks, bolders and natural contoured

soil, temporary earthwork supports, dewatering ( if any ) as

per specifications sections 02200

01 Excavation for foundations commencing from existing grade level 73752 M

Backfilling

02 Approved selected imported fill material including compaction in 2300 M

making up levels around and over foundations, beds and the like as

per spec. sections 02200

03 Approved fill material selected from excavated material including M price only

compaction as per specification section 02200

Soil treatment application for termite control

04 To subgrades of slabs and along periphery of building The work 19170 M

shall include all materials and equipments required to complete

and finish the work according to specifications and code of

practice

To Collection SR



15 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

16/67




AMOUNT


DIVISION 2 - SITE WORK

TRAFFIC MARKING DIMENSION

Thermoplastic paint for traffic marking on parking pavement

as detail 11 shown on drawing CL-GA-901 and specification

01 Straight arrows 78 No.

02 Turning arrows 1 No.

03 Parking lane marking 1465 M

04 Handicapped marking on floor 19 No.

05NO ENTRY (text)

3 No.

06 EXIT (text) 3 No.

07 Lane numbers 142 No

To Collection SR

Collection

Sheet - 15

Sheet - 16

To Bill Summary SR



16 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

17/67




AMOUNT


DIVISION 3 - CONCRETE

CONCRETE WORK

CONCRETE TYPES

Include in Unit Rates for concrete of the following types and

locations:

20 Mpa

a) Blinding concrete

b) Catch basins and side walks Note

40 Mpa

a) Footings

b) Columns and R.C. walls

c) Floor and roof slabs, beams, girders, stairs

d) Concrete topping or structural screed

e) Slab on grade

f) water tanks

Water stops including junction accessories are not measured

separately The cost of water stop items are to be included in the

unit rates of the related concrete items

To Collection



17 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

18/67




AMOUNT



Plain insitu concrete, 20 Mpa, cement type Vas per specifications section 03300

01 Screed, 50mm thick 1057 M

02 Blinding beds, 100mm thick 2113 M

Supply and placing Insitu reinforced concrete, 40 Mpa

cement type V including formwork and steel reinforcements

conforming to ASTMA615and A185 and all requiments to

finish the work according to drawings as per specifications

sections 03100, 03200 & 03300 , and code of practice in:

03 Raft foundation various thickening including depression areas, 14300 M

sump pits and elevators pits and electrical cables trench

04 Retaining walls 855 M

05 Reinforced concrete for tanks 521 M3

To Collection



18 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

19/67




AMOUNT



CONCRETE WORK

Supply and placing of Insitu reinforced concrete, 40 Mpa

type I cement including formwork and steel reinforcements

conforming to ASTM A615 and A185 and all requirements to

finish the work according to the drawings,as per

specifications sections 03100, 03200 & 03300,and code of

practice

01 Columns 477 M

02 Shear wall 424 M

03 Beams 71 M

04 Suspended flat slabs, 300mm thickening including drop panel 2718 M



07 Ramps 70 M

08 Stairs including landings 84 M

PRECAST CONCRETE

Precast concrete wheel stopper including dowels, grouting

and accessories for complete installation as per detail 21 on

drawing CL-GA-901 and specification

09 Precast concrete wheel stopper including fixings 375 No.

To Collection SR



19 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

20/67




AMOUNT



CONCRETE WORK

Sundries

01 Allow for reinforced concrete equipment pads including upstand 17 M

surrounds and anti-vibration accessories as required

02 150mm thick raised slabs, Handicapped`s ramps and curbs to suit 645 M

required areas as per detail 10,14, 20 on drawing CL-GA-901

03 Reinforced concrete electrical cable trench including all associated 48 M

works

To Collection SR

Collection

Sheet - 17

Sheet - 18

Sheet - 19

Sheet - 20

To Bill Summary



20 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

21/67




AMOUNT


DIVISION 4 - MASONRY

UNIT MASONRY

Supply and fix concrete masonry blocks in courses with

cement lime mortar including concrete lintels over

openings , horizontal and vertical reinforcement, fixings,

fillers, sealants and grout to complete the work according

to specifications and drawings

01 15 mm thick wall, one hour fire rated 42 M

02 200 mm thick wall 37 M


04 200 mm thick wall, two hours fire rated 487 M


To Bill Summary SR



21 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

22/67




AMOUNT


DIVISION 5 - METALS

Expansion joint

Supply and install expansion joint cover including

extruded aluminum assembles, fillets, accessories, fixing

and sealants as per drawing CL-GA-902 and according to

specifications

01 Floor to floor cover as per detail no. 1a 2300 M

02 Wall to wall cover as per detail no. 1b 1450 M

03 Wall to wall cover as per detail no. 1e 1705 M

04 Floor to wall cover as per detail no. 1d 750 M

05 Ceiling to ceiling cover as per detail no. 1j 1200 M

06 Wall to ceiling cover as per detail no. 1h 400 M

Steel cover as per details on drawings

07 To suit electrical cable trench 68 M2

08 To suit sump pits at basement 7 No

Supply and install 30mm depth panted galvanized cast iron

gratings including 40x40mm steel angle, medium gauge

galvanized gutter slope to drain and all required for fixing

and finisheng as per detail no.9 on drawing CL-GA-901 and

specificatons

09 To suit required locations 24 M

To Bill Summary SR



22 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

23/67




AMOUNT


DIVISION 7 - THERMAL AND MOISTURE PROTECTION

Water proofing and moisture protection as per specificationsection 07100

01 Membrane waterproofing as per specifications to suit base slab and 30800 M2

retainig walls

02 Protection board to suit base slab and retainig walls 2380 M2

To Bill Summary SR



23 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

24/67




AMOUNT


DIVISION 8-DOORS AND WINDOWS

DOOR SETS

Supply and install all doors to suit masonry openings and Note

approved samples including fixings, decorations, frames,

architrave, hardwares and saddles and all required to complete

and finish the work as detailed on drawing CL-GA-801 and

according to specifications and code of practice

TYPE B : 44mm thick painted hollow metal insulated

door including door grill (where required)

01 Type B1, single leaf door, size 900x2150mm and 45 min. fire rated 7 No.

02 Type B6, double leaves door, leaf size 950x2150mm and 45 min. fire 6 No.

rated

. .

motorized adjustable louvers panel working upon signal from

fire alarm system for generator .

03 Type C1, double leaves door, leaf size 950x2400mm and 45 min. fire 7 No.

rated

04 Type C2, double leaves door, leaf size 1050x2400mm and 45 min. 1 No.

fire rated

WINDOWS

24 mm thick double tempered glazed sliding window tinted

outside clear inside , on powder coated aluminum frame

including all hardware, fixtures, packings, sealants, weather

strippings and the like as described drawing CL-GA-801 to suit

opening and as per specification

05 Ref. W02 3 No

To Bill Summary SR



24 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

25/67




AMOUNT


DIVISION 9 - FINISHES

INTERNAL FINISHES

Flooring including respective types of bounding materials,

concrete screed sub-floor of required thickness, (if any)

accessories for complete installations as per ID drawing

and specification

01 Epoxy paint on cement screed. , ref. EC 368 M

02 Anti carbonation protection epoxy coating for pavement. , ref. AEC 4302 M

03 8mm thk. heavy duty multi component epoxy screed with 352 M

polyurethane base on concrete screed for car ramps,supported withlinear metal strip for non sliding. , ref.HES

04 Multi component epoxy coating on concrete screed for drive way & 8105 Mturns. , ref. MEC

Finishings : walls including metal angle beads and lathing at

junctions of differing backgrounds

05 Cement plaster to suit walls 7630 M

06 Paint on cement plaster ,ref. W01 7630 M

Finishings : ceilings

07 Cement plaster to suit ceiling 15950 M

08 Paint on cement plaster, ref.C01 15950 M

To Collection SR



25 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

26/67




AMOUNT


DIVISION 9 - FINISHES

EXTERNAL FINISHES

Finishing : walls including metal angle beads and lathing at

junctions of differing backgrounds

01 Cement plaster to suit external surface 66 M2

02 External Paint on cement plaster to suit external surface 66 M2

To Collection SR

Collection

Sheet - 25

Sheet - 26

To Bill Summary



26 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

27/67




AMOUNT


DIVISION 10 -SPECIALTIES

CORNER & COLUMN GUARD

Corner guards install at 600 high from finish floor heavy duty

rubber guard bumper, including all associated works, as per

detail 18 shown on drawing CL-GA-901 and as specification

01 To suit column location as required 63 No

ALUMINUM LOUVERS SCREEN

Supply and install fixed anodized aluminum sand trap louvers

panels on anodized aluminum frames including finishes and all

associated works to complete and fix the works as per detailson drawing CL-GA-802 and specification

02 Ref. L03, size 3200x2500mm to suit required locations 2 No






To Collection SR



27 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

28/67




AMOUNT


DIVISION 10 -SPECIALTIES

SIGNAGE

Manufacturer's standard indoor signs, letters and plaques

including fixings, finishes, accessories complete as per

interior design drawings CL05-i901 to CL05-i907 and all

required materials and equipments to complete and finish

the works according to specifications, drawings and code of

practice

01 Ref. type S01 18 No







To Collection SR

Collection

Sheet - 27

Sheet - 28

To Bill Summary SR



28 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

29/67




AMOUNT


DIVISION 14 - CONVEYING SYSTEMS

AUTOMATED WASTE COLLECTION SYSTEM

Supply and provide all required to construct, test and operate

automated waste collection system, consisting of the

following items:-

01 Discharge valve room with basement floor including all required 14 No.

works as detailed on drawing no. STM - ITCCP2 - TD - 008.

Contractor shall perform all required coordination with other trade to

ensure proper installation and operation of the complete system to

transport waste from tower chute to pipe networks as shown on

drawings STM - ITCCP2 - TD - 001 to 007 and 015, 016 andaccording to manufacturer's standards and specifications

02 Discharge valve room without basement floor including required 3 No.

earthworks, concrete works for the vacuum room masonry for the

vacuum room and electromechanical works and all required works

as detailed on drawing no. STM - ITCCP2 - TD - 009. Contractor

shall perform all required coordination with other trades to ensure

proper installation and operation of the complete system to

transport waste from tower chute to pipenetworks as shown on

drawings STM - ITCCP2 - TD - 001 to 007 and 015, 016 and

according to manufacturer's standards and specifications

PIPE WORK

Supply and installation of Automated waste collection system

piping. Item shall include the earth works, insulation,

,concentric reducer, puddle flanges ,inspection covers and all

required materials and equipments to complete the transport

pipe line from DV rooms , outdoor load stations and full

vacuum load stations to waste plant

03 508mm under/above ground transport pipe 1070 M

RC MANHOLE

Supply and install cast insitu or precast reinforced concrete

manhole ,the item shall include excavation, backfill

insulation ,inspection cover steel rungs and all required tocomplete the work.

04 RC manhole to suit required location in sitesas shown on drawings 29 No.

STM - ITCCP2 - TD 001 to 016

To Bill Summary SR



29 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

30/67




AMOUNT


DIVISION 15 - MECHANICAL

PLUMBING INSTALLATIONS


Supply, installation and test drainage pipe work UPVC

schedule 40 the work shall include but not limited to fittings,

supports hangers, excavation, backfilling, cast iron pipes on

roof for vent with caps and all materials and equipment


specifiactions, drawings and code of practice

01 32 mm dia 150 M

02 50 mm dia 210 M

03 100 mm dia 490 M

04 150 mm dia 940 M

Accessories

05 Area drain 150mm dia., ref. AD 21 No.

06 Floor drain, 50 mm dia., ref. (FD) 22 No.

07 Parking drain, 150mm dia., ref. PD 57 No.

08 Cleanout, 75 mm dia., ref. (CO) 36 No.

09 Cleanout, 100 mm dia., ref. (CO) 138 No.

To Collection SR



30 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

31/67




AMOUNT





Accessories

01 Floor cleanout 100mm dia., ref. (FCO) 41 No.

02 Floor cleanout 150mm dia., ref. (FCO) 22 No.

03 Gully trap, ref. GT 16 No.

04 Trench drain outlet, 100mm dia., ref. TDO 3 No.

Reinforced concrete gray water tank with required capacityand proprietary medium duty cast iron manhole cover and

frame, including sump pit, submersible pumps, internal

lining, access ladder vent pipework within tank as detailed

on drawing (Concrete work, earthwork & water proofing

measured elsewhere)

05 Gray water tank 10 No

Packaged type variable speed discharge pressure system

Gray water lift pumps, including piping and valves network

within pump chamber, complete with all controllers,

accessories for automatic operation as scheduled on

drawing as per spec. section 15453

06 Gray water lift pumps CAP. 5 KW 5 Set

07 Gray water lift pumps CAP. 6 KW 5 Set

Reinforced concrete sump pit including internal lining,

proprietary galvanized steel manhole cover and frame,

guide bar, lifting chain and all associated works, valves

pipework within sump pit chamber as detailed on drawings

(concrete work & earthwork, waterproofing measured

elsewhere)

08 Sump pit 7 No.

To Collection SR



31 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

32/67




AMOUNT





Submersible pumps (one duty and one stand-by) including

associated valves, pipework, valves controllers and

accessories within sump pit chamber as described on

drawings (sump pit measured separately)

01 Ref. SP1 capacity 1.5 HP 5 Set

02 Ref. SP2 capacity 2 HP 2 Set

Allow for the design, supply and installation of packaged

type waste water treatment plant complete including filter,chemical feeders, air blowers controls, wirings, piping and

all as associated works as per specifications section 02736

and scheduled on drawing

03 Packaged water treatment unit. Cap. 58 m3/day 9 No.

POTABLE WATER INSTALLATION

Supply, installation and test pipework, plypropylene

for potable water the work shall include but not limited

to installation, fittings, insulation for hot pipework,

valves, supports and all materials and equipment

required to complete and finish the work according tospecifications, drawings and code of practice

04 20 mm dia. 835 M

05 25 mm dia. 205 M

06 50 mm dia. 685 M

07 63 mm dia. 165 M

08 100 mm dia. 485 M

To Collection SR



32 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

33/67




AMOUNT




NON-POTABLE WATER INSTALLATION

Supply, installation and test pipework, plypropylene

for non-potable water the work shall include but not limited

to installation, fittings, insulation for hot pipework,

valves, supports and all materials and equipment


specifications, drawings and code of practice

01 50 mm dia. 1585 M

02 63 mm dia. 80 M

03 75 mm dia. 610 M

04 100 mm dia. 505 M

Accessories

05 Water meter assembly 63mm dia., 14 No.

06 Isolating valve, 50 mm dia, ref. (IV) 33 No.



09 IV & CV assembly 100 mm dia., 7 No.

10 Hose bib 20mm dia., ref. (HB) 51 No.

To Collection SR



33 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

34/67




AMOUNT




Packaged type duplex unit discharge pressure system

potable water lift pumps, (one duty & one stand by)

including piping and valves network within pump chamber,

complete with all controllers, accessories for automatic

operation as scheduled on drawing and specification

section 15453

01 Potable water pump CAP. 7.17 KW 6 Set

02 Circulating potable water pump CAP. 0.5 HP 6 Set

Reinforced concrete under ground water tank and pump

room with required capacity and proprietary cast ironmanhole covers and frames, including internal lining

access ladders, pipework submersible pump, ventilating

fans with exhaust and fresh air pipework, valves, vent pipes

and truck fill pipework as detailed on drawings (concrete

work & earthwork, water proofing measured elsewhere)

03 Potable Water tank 6 No.

To Collection SR



34 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

35/67




AMOUNT




Supply, installation and test Pipework, UPVC class 5

including fittings, trenching, back fill supports system and

all associate works as per code standard

01 25 mm dia. 3155 M

02 32 mm dia. 405 M

03 40 mm dia. 745 M

04 50 mm dia. 405 M

05 100 mm dia. 1725 M

06 150 mm dia. 795 M

07 200 mm dia. 60 M

Accessories

08 Pendent sprinkler head 126 No

09 Upright sprinkler head 1239 No

10 Side wall sprinkler head 14 No

11 100mm Fire departement valve , ref. FDV 31 No

12 Floor control valve assembly 100mm dia., ref. FCVA 3 No

13 Floor control valve assembly 150mm dia., ref. FCVA 7 No

14 Fire department connection, 2 way fire department inlet

connection type with gate and check valve 100mm dia. 2 No

15 Fire department connection, 2 way fire department inlet

connection type with gate and check valve 150mm dia. 3 No

To Collection SR



35 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

36/67




AMOUNT




Supply, install, testing and commissioning proprietary

integrated fire hose reel and fire extinguisher cabinet the

work shall include but not limited to fire extinguisher, hose

reel nozzle, fixings, isolating valve 40 mm dia., trims and

all associate works and all materials and equipments


drawings, specification and code of practices

01 Ref. FHC 18 No

Supply, install, testing and commissioning portable

multipurpose fire extinguisher the work shall include butnot limited to fixing to wall, all associate works and all

materials and equipments required to complete and finish

the work according to drawings, specification and code of

practices

02 Ref. PFE 3 No

03 Ref. CO2 33 No

CO2 system

Supply, install and test CO2 cylinders including pipe work,

black steel seamless for CO2 fittings, supports valves,

regulators, sleeves, as shown on drawings and as per

specification

04 CO2 cylinders CAP 45 KG 38 No.

05 Control panel 14 No.

06 Remote manual release 14 No.

07 Abort switch 14 No.

08 Alarm bell 14 No.

09 4-port nozzle 14 No.

10 Ioization detector 14 No.

To Collection SR



36 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

37/67




AMOUNT




DIESEL FUEL STORAGE TANK INSTALLATION

Allow for underground fiberglass diesel fuel storage tank

with required capacity including concrete anti-flotation

pad, heavy duty traffic type manhole ring and cover,

pipework, valves duplex diesel fuel transfer pumps, steel

ladder, pea gravel bed, earthworks, fixings and accessories

all as detailed on drawings

01 Proprietary tank units CAP. 3800 Lit. 3 No.

To Collection SR

Collection

Sheet -29

Sheet -30

Sheet -31

Sheet -32

Sheet -33

Sheet -34

Sheet -35

Sheet -36

Sheet -37

To Bill Summary SR



37 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

38/67




AMOUNT


DIVISION 15B - MECHANICAL

HVAC INSTALLATIONS

CHILLED WATER SYSTEM

Supply, install and test black steel pipework including

fittings thermal insulation, flexible connections and

accessories as per required drawings and specification

sections15050 to 15140 ,15510

01 15 mm dia. 265 M

02 20 mm dia. 70 M

03 25 mm dia. 20 M

04 32 mm dia. 200 M

05 100 mm dia. 810 M

06 150 mm dia. 505 M

07 200 mm dia. 270 M

08 250 mm dia. 120 M

09 350 mm dia. 55 M

10 400 mm dia. 465 M

11 450 mm dia. 15 M

To Collection SR



38 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

39/67




AMOUNT



HVAC INSTALLATIONS


Supply and install valve / BTU meter

Butterfly valve

01 Ref. MBFV 400 mm dia., 1 No.

Isolating valve

02 32mm dia., 34 No.

Check valve

03 32mm dia., 17 No.

BTU meter

04 32mm dia., 17 No.

Supply and install heat exchanger including valves and

short length piping as detailed on drawings and as per

specifications

05 Ref. HEX-01 to 05, 1960 KW capacity 5 No.

Supply, install, test and commission, variable speed chilled

water centrifugal inline pumps unit including valves, flexible

connections, Y-striners, mounting and fixing to pads

(measured separately) as detailed on drawing and

specifications

06 Ref. CWP-01 to 05, 52.0 L/S capacity 45 m TDH 5 No.

To Collection SR



39 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

40/67




AMOUNT



HVAC INSTALLATIONS


Supply, install and commission, expansion tank as detailed

on drawings and specifications

01 Ref. ET, 1200 liter capacity 1 No.

Supply, install and commission, air separator tank as

detailed on drawings and specifications

02 Ref. AS 1 No.

Supply, install, test and commission, Fan coil units ducted

type including control valves, pressure & temperature,

gauge, Y-strainer mounting and fixing as per drawings and

specifications section 15781

03 Ref. FCU-02, 17.1 KW cooling capacity 2 No.




Supply, install, test and commission DX-ducted split unit

including control, pipes and fixing as per drawing and

specifications

07 Ref. RAC-01, 3.51 KW nominal coollling capacity 51 No.

Supply, install, test and commission, DX-ducted split unit

including control, pipes and fixing as per drawings and

specifications section 15781

08 Ref. FCU-01/ACCU-01 , 4 KW capacity 3 No.

Supply, install, test and commission automatic chemical

dosing unit as detailed on drawings and specifications

09 Ref. ACDU 1 No.

To Collection SR



40 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

41/67




AMOUNT



HVAC INSTALLATIONS

Supply, install, test and commission, Ventilating fans as

details on drawings and specifications, section 15860

01 Ref. PEF- 01, 13500/22500 LPS capacity with exh. Duct and 6 No.

CAP.

02 Ref. EF- 01, 85 LPS capacity 3 No.






08 Ref. BIF-01, 3600 LPS capacity 24 No.

Supply, install, test and commission, Supply air round

ceiling diffusers with opposed blade volume damper

including frame trims & insulated plenum box as detailedon drawing and specification, section 15860

09 Ref. SD1 26 No.

10 Ref. SD2 28 No.

11 Ref. SD3 616 No.

To Collection SR



41 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

42/67




AMOUNT



HVAC INSTALLATIONS

Supply, install, test and commission, supply air register as

detailed on drawings and specification

01 Ref. SR 1 / RR1 8 No.

Supply, install, test and commission, Return round louver

face ceiling diffusers as detailed on drawing and

specification

02 Ref. RD1 26 No.

03 Ref. RD2 28 No.

04 Ref. RD3 6 No.

Supply, install, test and commission, door grill as detalied

and specificaitons

05 Ref. DG1 18 No.

06 Ref. DG3 2 No.

Supply, install and test motorized door louver as detailedon drawing and specification

7 No.07 size 950 x 2200 mm

Supply and install Galvanized steel sheet rectangular

ductwork, including supports and volume damper , and bill

mouth opening as per drawings and specification

08 Various gauges 985 Kg

Supply and install Duct insulation

09 Thermal semi-rigid insulation to rectangular ductwork 250 M

Supply, install and test generator exhaust ductwork with

canvass connection

10 To suit generator room 3 No.

To Collection SR



42 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

43/67




AMOUNT



HVAC INSTALLATIONS

Supply, install, test and commission, of electric works and

motor control centers MCC C/W weather proof, magnetic

starters, cabinets including power cables, wiring and

conduits and cable trays from the MCC to HVAC equipment,

interlocks, earthing ...etc, all materials and equipments


drawings, specifications and code of practices

01 Ref. MCC- CWP 1 No.

To Collection SR

Collection

Sheet - 38

Sheet - 39

Sheet - 40

Sheet - 41

Sheet - 42

Sheet - 43

To Bill Summary SR



43 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

44/67




AMOUNT


DIVISION 16 - ELECTRICAL

MEDIUM VOLTAGE INSTALLATION

MVSWGR (medium voltage switchgear)

Supply , install , testing and commissioning 13.8 KV, 3 phase,

60 Hz,SF6 MVSWGR with 3 cells (1 inputs +2 outputs)

including all associated works to complete installation as per

drawings and specifications. The contractor shall prepare

sketches and details for approval from SEC and shall make

arrangement and required coordination with supervising

engineer to complete the work

01 M.V Switchgear unit ref (MVSWGR/CL-5) 1 No

RING MAIN UNIT

Only installation, testing and commissioning for 13.8 KV, 3

phase, 60 Hz SF6 ring main unit including all associated

works for complete installation as per drawings and

specifications and required coordination (supply will be by

client)

02 Ring main unit RMU1,2,3.4 4 No

MEDIUM AND LOW VOLTAGE DISTRIBUTION

Supply installation, testing and commissioning of the

following equipment including all accessories and

necessary works required for installation as shown on the

drawings E-701,E201 and as described in specifications

section 16461,16124and and by making arrangiement with

supervising engineer to achieve the work to the best

possible and specifications

03 Dry type transformers , 1000 KVA, 13.8 KV ,400/230V , 3PH, 3 No.60HZ, ref (TR 1,2,4-CL5)

04 Dry type transformers, 1600 KVA, 13.8 KV ,400/230V , 3PH, 60HZ, 1 No.ref (TR 3-CL5)

To Collection SR



44 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

45/67




AMOUNT



MEDIUM VOLTAGE INSTALLATION

Supply , install and test medium voltage copper Cables 15KV/

XLPE/STA/PVC, between medium voltage equipments as

shown on drawings and coordination with other disciplines

shall be conducted during work execution as per technical

specifications, drawings and by making arrangement with

supervising engineer to achieve the work to the best possible

and specifications

01 Medium voltage cable comprising 3 core 70 mm CU / XLPE /STA/ 20 M

PVC, cables route from RMU up to transformers

02 Medium voltage cable comprising 3 core 300 mm CU / XLPE /STA/ 485 M

PVC, cables

Smart Metering System

Supply, installation , testing and commissioning of Smart

Metering System comprising of M-bus master controller

complete with soft ware and bus IP router, including digital

electrical KWH meters, 1 pair twisted cable # 22 AWG type

to TCP/IP net work and all associated works required as

shown on drawing E-501--E520 and as described inspecifications section 16211

To suit Building Smart Metering System with multi -electronic

meter (MEM) and main bus and IP router as required to form a Note

complete and fully operative system to link all project buildings

with the existing data center at phase 1

03 Electronic KWH meters 17 No

04 M-bus master controller complete with software 17 No

05 M-bus IP router 17 No

To Collection SR



45 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

46/67




AMOUNT



MAIN AND SUB-MAIN POWER

Supply and install an Emergency Power Generating Sets

including Generator Control Panel (GCP). In addition to

circuit breakers, pads, supports, controls and daily diesel

fuel storage tank, including all necessary equipment,

accessories and associated works, as shown on drawings

E-701,E201 as described in specifications section 16231,

and by making arrangiement with supervising engineer to

achieve the work to the best possible and specifications

01 Ref. (G1,G3) 550 KVA, 3 phase 4 wire ,400/230V , 60 Hz. 2 No.

02 Ref. (G2) 600 KVA, 3 phase 4 wire ,400/230V , 60 Hz. 1 No.

supply , install, testing and commissioning multicore copper

cable ( XLPE/PVC -1000/600V) in cable tray or cable trench

(measured elsewhere) including junction boxes, connection

for feeders and various power loads as shown on drawings

E-701 and as per specification section 16126 and by makingarrangement with supervising engineer to achieve the workto the best possible specifications

03 (4 C-10 mm ) + 10 mm G/ cable tray 115 M

04 (4 C-16 mm ) + 16 mm G /cable trench 20 M

05 (4 C-25 mm ) + 16 mm G/ cable tray 345 M

06 4 C-35 mm + 16mm G/ cable tray 200 M

07 4 C-50 mm + 25mm G/ cable tray&cable trench 665 M

08 4 C-70 mm + 35mm G/ cable tray 60 M

09 4 C-95 mm + 50mm G/ cable tray&cable trench 265 M

10 4 C-185 mm + 95 mm G/ cable tray&cable trench320

M

11 4 C-240 mm + 120 mm G/ cable tray&cable trench 785 M

12 2(4C-150mm2) + 150 mm G/ cable tray 875 M

13 2(4C-240mm2)/ cable trench 15 M

To Collection SR



46 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

47/67




AMOUNT



supply , install, testing and commissioning multicore coppercable ( XLPE/PVC -1000/600V) in cable tray or cable trench

(measured elsewhere) including junction boxes, connection

for feeders and various power loads as shown on drawings

E-701 and as per specification section 16126 and by makingarrangement with supervising engineer to achieve the workto the best possible specifications

01 3(4X1C-630mm2)/ cable trench 35 MThe length of cables including the cluster-5 cables and cables in Notethe first floor for AP03 & AP04 & AP06 according to No. for each

AP in site

Supply , install , power distribution heavy duty galvanizedsteel cable trays with cover including fixings, supports and all

accessories as shown on drawingsE201--E220 and

coordination & integration with other systems shall be

conducted during work execution as per technical

specifications section 16050 and by making arrangement with

supervising engineer to achieve the work to the best possible

specifications

02 Cable tray 200 mm width 152 M

03 Cable tray 200 mm width for emergency cables 540 M



05 Cable tray 400 mm width for emergency cables 50 M

06 Cable tray 400 mm width double layers 50 M


08 Cable tray 600 mm width double layers 25 M



11 Covered cable tray 300 mm width for optical fiber cables and 1955 M

primary and secondary networks.

To Collection SR



47 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

48/67




AMOUNT




supply and install reinforced concrete Man / Holes connected

via duct banks, complete with man / hand hole bolted type

metal cover, drain pipe outlet, including trenching and

backfilling for duct banks, conduits for M.V cables in duct

banks, tapes, all as required to suit locations as shown on

drawings drawings E201--E220and as all accessories and

coordination & integration with other systems shall be


specificationssection 16180 and by making arrangement with

supervising engineer to achieve the work to the best

possible specifications

01 Power Man Holes (180018001800 )Ref. MH for power including 4 No

UPVC conduit

02 Power Hand Hole (900900900 ) Ref. HH including UPVC conduit 7 No

03 Comm, Hand Hole (600600600 ) Ref. CHH including UPVC conduit 5 No

Site work

04 Power Man Hole Ref. PHH for power including UPVC conduit 4 No

05 Power Hand Hole (900900900 ) Ref. HH including UPVC conduit 3 No

To Collection SR



48 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

49/67




AMOUNT




Supply , install , testing and commissioning of panel boards

including grounding, circuit breakers, grounding, fixings,

markers and , other functional units and all associated works

as required and shown on drawings E 701,E704 , E201--E220

and coordination & integration with other systems shall be


specificationssection 16442,16410,16415 and by makingarrangement with supervising engineer to achieve the workto the best possible specifications

01 Ref. MDP-P1 1 No.




05 Ref. EMDP-P1 1 No.



08 Ref. DP31 12 No.

09 Ref. DP32 12 No.

10 Ref. DP41 2 No.

11 Ref. DP42 2 No.

12 Ref. DP61 3 No.

13 Ref. DP62 3 No.

14Ref. DPSB1

1 No.

15 Ref. DPSB2 1 No.

16 Ref. EDPS3 12 No.

To Collection SR



49 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

50/67




AMOUNT




Supply , install , testing and commissioning of panel boards

including grounding, circuit breakers, grounding, fixings,

markers and , other functional units and all associated works

as required and shown on drawings E 701,E704 , E201--E220

and coordination & integration with other systems shall be


specificationssection 16442,16410,16415 and by makingarrangement with supervising engineer to achieve the workto the best possible specifications

01 Ref. EDPSB1 1 No.

02 Ref. EDPSB2 with interlock and ATS built in 1 No.

03 Ref. EPMSB1A 1 No.

04 Ref. EPMSB2B 1 No.

05 Ref. EPMSB2A with interlock and ATS built in 1 No.

06 Ref. EPMSB2B 1 No.

07 Ref. EDPSB3A 1 No.

09 Ref. EPSB1 1 No.

10 Ref. EPSB2 1 No.

11 Ref. EPSC 12 No.

12 Ref. EPSC1 2 No.

13 Ref. EPSE 3 No.

14 Ref. PPSB1 1 No.

15Ref. PPSB2

1 No.

16 Ref. PPSC 12 No.

17 Ref. PPSC1 2 No.

To Collection SR



50 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

51/67




AMOUNT




Supply , install , testing and commissioning of panel

boards including grounding, circuit breakers, grounding,

fixings, markers and , other functional units and all

associated works as required and shown on drawings E

701,E704 , E201--E220 and coordination & integration with

other systems shall be conducted during work execution as

per technical specificationssection 16442,16410,16415 andby making arrangement with supervising engineer toachieve the work to the best possible specifications

01 Ref. PPSE 3 No.

02 Ref. SLP1A 1 No.

03 Ref. SLPE 6 No.

Pump room

04 Ref. EPP (IP 54 ) 1 No.

To Collection SR



51 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

52/67




AMOUNT



POWER INSTALLATION

The contractor is to insure that all power outlets mounted in Notewet areas and all service outlets for kitchens, bathrooms,laundry and water heaters are to be protected by centralground fault circuit interrupter (GFCI)

Supply , install, testing and commissioning of power and

sockets accessories including all necessary boxes,

faces(according to the engineer approvement ) comprising

cables, conduits, fittings, connections, from the outlets to

Panelboards feeder associated works as required to suit the

locations shown on drawings E201--E220 Coordination with

other disciplines shall be conducted during work executionas per technical specifications, section 16050and by making

arrangiement with supervising engineer to achieve the work

to the best possible specifications

01 Junction box ceiling mounted 34 No.

02 Junction box, wall mounted 77 No.

03 Disconnect switch,non-fused and with pilot light16A, 1P, 230V 14 No.,weatherproof for waste collection equipment

04 Above false ceiling disconnect 20A, 1P, 230V for FCU-03.04,05 33 No.

05 Disconnect switch,non-fusedand with pilot light 20A, 1P, 230V 10 No.,weatherproof for SP-01,02,03,04,05,06&fuel pumps

06 Disconnect switch,non-fused and with pilot light 20A, 1P, 230V 57 No.

for BD3,4,6&FDB1,2,FD3G,FD4G,FD6G&FACP&A/P switcher

07 Disconnect switch, fused and with pilot light 20A, 1P, 230V 54 No., for RAC& RAC-01&FCU-02

08 Disconnect switch, non-fused and with pilot light 20A, 3P, 380V 16 No.,weatherproof for gray& potabole pumps

09 Above false ceiling disconnect 20A, 3P, 400V for BIF-01 24 No.

To Collection SR



52 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

53/67




AMOUNT



POWER INSTALLATION







other disciplines shall be conducted during work execution

as per technical specifications, section 16050and by making



01 Disconnect switch, fused and with pilot light ,32A, 1P, 230V 4 No.

for FCU-01

02 Disconnect switch, non-fused and with pilot light ,50A, 3P,400V 6 No.

for PEF-01

03 Disconnect switch, non-fused and with pilot light ,500A, 3P,400V 1 No.

weatherproof for jocky pump, MCC-CWP

04 Circuit breaker 200A for fire alarm panel (magnetic trip only) 1 No.

05 Motor switch with built -in over load protection (tumbler switch) 32 No

06 For exhust fan outlet 34 No.

07 Single socket outlet, 10A, 230V, grounding type 256 No

08 Single socket outlet, 13A, 230V, grounding type, weatherproof 102 No

09 Single socket outlet, 16A, 230V, grounding type, EF 34 No

10 Single socket outlet, 16A, 230V, grounding type, EF 34 No

11 Duplex socket outlet, 16A, 230V, grounding type 8 No

To Collection SR



53 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

54/67




AMOUNT



POWER INSTALLATION







other disciplines shall be conducted during work execution

as per technical specifications, section 16050and by making



01 Single pole one-way ,one gang switch (13A) 108 No.

02 Single pole one-way ,two gang switch (13A) 20 No.

03 Push button switch 55 No.

Site work

04 Junction box ,floor mounted for site 2 No.

Pump rooms

05 Junction box ceiling mounted 1 No.

06 Disconnect switch, non-fused and with pilot light 20A, 1P,230V 1 No.

weatherproof for sub. pump

07 Disconnect switch, non-fused ,200A, 3P,400V, weatherproof for 1 No.

fire& jockey pump,

08Motor switch with built-in over load protection (tumbler switch), 1 No

weatherproof

09 Single socket outlet, 13A, 230V, grounding type, weatherproof 1 No

10 Single pole one-way ,one gang switch (13A), weatherproof 1 No.

To Collection SR



54 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

55/67




AMOUNT



LIGHTING INSTALLATION

Supply, install , testing and commissioning of lighting

fixture outlets and including conduits, wires and all boxes

belong to Lighting Panelboards and associated works as

required to suit the locations shown on drawings E101--E120

.Coordination with other disciplines shall be conducted

during work execution as per technical specifications,

section 16050 and by making arrangiement with supervising

engineer to achieve the work to the best possible

specifications

01 Lighting fixer outlet 1588 No.

Pump room

02 Lighting fixer outlet 4 No.

To Collection SR



55 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

56/67




AMOUNT



LIGHTING INSTALLATION

Supply ,install, testing and commissioning of lighting

fixture (furnishe with lamp and electronic blast, accessories

and internal wires) mounting accessories.(according to the

engineer approval ) associated works as required to suit the

locations shown on drawings E101--E120 ,GE-E01,GE-E01 and

Coordination with other disciplines shall be conducted

during work execution as per technical specifications,

section 16500 and by making arrangiement with supervising

engineer to achieve the work to the best possible

specifications

01 Type EX ( wall mounted, single sided) 71 No.

02 Type EX ( ceiling mounted, single sided) 47 No.

03 Type F1 522 No.

04 Type F1E 142 No.

05 Type F2 308 No.

06 Type F2E 96 No.

07 Type F7E 130 No.

08 Type F8E 112 No.

09 Type NE 20 No.

10 Type WL3 55 No.

11 Type WL4 8 No.

12 Type WL4E 41 No.

13 Type FT1 flixible tube LED cove light 998 M.

Pump room

14 Type F1E 4 No.

To Collection SR



56 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

57/67




AMOUNT



GROUNDING SYSTEM

Supply, installation , test and commissioning of a grounding

system comprising bare copper conductor to bond the

building's distribution boards and HVAC equipments to the

main ear thing grid of the building. Including necessary

earthwork, buried galvanized steel foundations strips

surrounding the building phosphor bronze test joints &

triangular counter poise and all associated works to suit

grounding resistivity required as shown on drawings

E301--E310 and as described in specifications16452,16453

by making arrangiement with supervising engineer to

achieve the work to the best possible specifications

01 Complete building grounding system network to suit ground 1 Item

resistivity as shown on drawings and specification

02 To suit grounding system for low current system equipment as 1 Item

shown on drawings and specification

03 To suit grounding system for Pump room as shown on drawings 1 Item

and specification

To Collection SR



57 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

58/67




AMOUNT



TELECOMMUNICATION SYSTEM

Supply, installation, testing and commissioning of

telecommunication system commporising of server,

Building distributor with core switch,floor distribution,

data/telephone outlets including cable / wires and conduits

as shown on drawings E- 501--E520 ,E801and as described

in specification section 16715,16720 and by making

arrangiement with supervising engineer to achieve the

work to the best possible specifications

To suit system network equipped with:

01 Building distributor ,ref ( BD3,BD4,BD6) contains main optical 3 No

data patch panel (F.O.P.P)

02 Floor distribution includes( fiber optical patch panel F.O.P.P ,

data switch CAT6 a 1 36 RJ 45 ports and UTP P.P CAT6 a 1

36 ports and blank ),ref FDB1 with UPS 1.5 KVA and 1 No

connected with power supply

03 Floor distribution includes( fiber optical patch panel F.O.P.P ,

data switch CAT6 a 1 48 RJ 45 ports and UTP P.P CAT6 a 1 No.

1248 ports and blank ),ref FDB2 with and connected with

power supply

04 Floor distribution includes( fiber optical patch panel F.O.P.P , 17

data switch CAT6 a 1 24 RJ 45 ports and UTP P.P CAT6 a 2 No.

24 ports and blank ),ref FD3G,FD4G ,FD6G with and

connected with power supply

05 Wall mounted telecommunication outlet 1 port (1data ) , ref. (T0) 27 No.

06 Ceiling mounted telecommunication outlet 1 port (1data ) , 77 No.

ref. (T0)

07 Wall mounted telecommunication outlet 1 port for intercome 17 No.

system

08 Wall mounted telecommunication outlet 1 port (1 Tel ) 38 No.

at 1500 mm A.F.F.L , ref. (T01)

To Collection SR



58 / 67

REVISED PAGE

Date: MAY 2012

7/28/2019 CL05 (MAY 2012)

59/67




AMOUNT

SRRATE

cl05 (may 2012)

Documents