chhattisgarh state industrial development corporation limited rcc hume pipe.pdfannexure -“a”...

No. 1/336 Chhattisgarh State Industrial Development Corporation Limited (A Government of Chhattisgarh Undertaking) First Floor, Udyog Bhawan, Ring Road No.-1, Telibandha , Raipur 492006 (C.G.) EPABX No.- 0771-6002071-73, Fax: 0771-4057624 (Mkt) CIN-U45203CT1981SG001853 PAN-AABCM6288N Service Tax Regn No.-AABCM6288NSD004 Website: www.csidc.in, Email : [email protected], [email protected]

No./CSIDC/MKD/ PS-VII /15-16/ Raipur, Dated :

SCHEDULE “C” LIST OF PARALLEL RATE CONTRACT FOR ITEM- RCC HUME PIPE

S.No. Name of the RC Holding Firm Valid Dated Rate Contract No.

1 2 3 4 01 M/s Aditya Industries,

C/o Dhansiram Bhajankumar, Rupdev Market, Deviganj Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300 Email- bhajan [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/AI/6467

02 M/s Surguja Cement Pipe Industries, Manendragarh Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300, 9826956300 Email- bhajan [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/SCPI/6468

03 M/s Raigarh Hume & Spun Pipe, Near Stadium, Industrial Area Raigarh (C.G.) Mo.- 9300676323, 9301010290 Email- [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/RH&SP/6469

04 M/s Dhanshri & Company, Deviganj Road Ambikapur Surguja (C.G.) 497001 Mo.- 09425580211 Ph.- 07774-235611

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/D&C/6470

05 M/s Agrasen Concrete Products, Navagarh Road, Bemetara Distt- Durg (C.G.) Mo.- 9977700300

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/ACP/6471

06 M/s Gopesh Cement Arts, Dayalband Bilaspur (C.G.) Mo.- 9300325947, 9827485186 Email- [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/GCA/6472

07 M/s Radheshyam Benishyam Kesary & Co., Dayalband Bilaspur (C.G.) Mo.- 9827167998, 9300333354 Email- [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/RBK&C/6473

08 M/s Bilaspur Cement Products, C/O Shri Sai Teles & Sanitary Main Road Tarwa Naka Bilaspur (C.G.) 495001 Mo.- 9425219302 9893968974 Ph.-07752-410302

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/BCP/6474

09 M/s Vasudev Shamji Savaria, Bajirao Mehrapara Raigarh (C.G.) 496001 Ph.- 07762-220050 Mo.- 099267-42045 Email- [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/VSS/6475

10 M/s Dinesh Industries, Telibandha, Near Gali No.- 6, Ravigram, Raipur Factory 730 A Industrial Estate Urla Raipur (C.G.) 492001 Ph.- 0771-3265888 Mo.- 9755042331 , 9926156001

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/DI/6476

No. 2/336

11 M/s Quality Cement Pipes, Add : 11,12 Industrial Estate Bhanpuri Raipur (C.G.) 493221 Ph.- 0771-4024190, Mo.- 9752005557

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/QCP/6477

12 M/s Raj Pipe, Infront of Industrial Estate, G.E. Road, Rajnandgaon (C.G.)

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/RP/6478

13 M/s Akash Pipe Industries, Dharampara Mungeli Bilaspur (C.G.) 495334 Mo.- 9993070099

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/API/6479

14 M/s Korba Cement Products, Urga-Korba (C.G.) Mo.- 9425224499 Email- [email protected]

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/KCP/6480

15 M/s Dhansree Concrete Products, Manendragarh Road Ambikapur (C.G.) 497001 Mo.- 9425580211

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/DCP/6481

16 M/s Shivshakti Industries, Kena Bandh Bouripara, Ambikapur, Distt Surguja (C.G.) 497001 Mo.-9425582023

31-03-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/14-15/RCCHP/SI/6482

17 M/s Jai Mahamaya Cement Pipe Industries, Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 Email- [email protected]

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/JMCPI/6483

18 M/s Jai Ambe Cement Product, Vill-Sargawan, Teh.-Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358, 9425254259

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/JACP/6484

19 M/s Jaiswal Cement Products, Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 , 9425254259 Email- [email protected]

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/JCP/6485

20 M/s Bhilai Cement Pipe Manufacturing co., 70-A,Industrial Estate , Nandini Road, Bhilai (C.G.) Ph- 0788-2286518 Mo.- 9893115028, 9981125028

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/BCPMC/6486

21 M/s Bhawani Cement Pipe Industries, Kh.No-521 D 1, Om Complex, Fafadih Village Deori Bilaspur Road Raipur (C.G.) 492001 Ph.-07714092724, Mo.- 9425507207

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/BCPI/6487

22 M/s Bastar Cement Products, Geedam Road, P.O Pandripani, Jagdalpur (Bastar) 494001 Mo.- 9826612012, 9425212012 Email- [email protected]

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/BCP/6488

23 M/s Engineers Enterprises, Rawabhata Industrial Area P.O. Birgaon Raipur (C.G.) 493221 Mo.-9826612012, 9425212012 Email- [email protected]

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/EE/6489

24 M/s Grewal Cement Pipe Industries, 31 Industrial Area, P.O Birgaon- 493221 Raipur (C.G.) Mo.- 9826612012, 9425212012 Email- [email protected]

10-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/GCPI/6490

No. 3/336

(Suresh Keshi) General Manager

25 M/s R.C.C. Hume Pipe & Products, S.U.I.E. Frazerpur Nayamundapara , Industrial Estate, Jagdalpur Bastar (C.G.) Ph.- 07782227204, Mo.-9425260321,9406286611 Email- [email protected]

30-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/RCCHP&P/6491

26 M/s Chhattisgarh Pipe Industries, Village - Bhoinabhata Tah. & Distt. Bemetara (C.G.) Mo.- 9993730777

30-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/CPI/6492

27 M/s Star Industries, Mukhtiyarpara Nagpur Manendragarh Korea (C.G.) Mo.- 09424260460, 09993251066

30-04-2015 To

01-04-2016

Rate Contract No. CSIDC/MKD/PS-VII /102/510/15-16/RCCHP/SI/6493

No. 4/336 S Chhattisgarh State Industrial Development Corporation Limited

(A Government of Chhattisgarh Undertaking) First Floor, Udyog Bhawan, Ring Road No.-1, Telibandha , Raipur 492006 (C.G.) EPABX No.- 0771-6002071-73, Fax: 0771-4057624 (Mkt) CIN-U45203CT1981SG001853 PAN-AABCM6288N Service Tax Regn No.-AABCM6288NSD004 Website: www.csidc.in, Email : [email protected], [email protected]


Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 To,

M/s Aditya Industries, C/o Dhansiram Bhajankumar, Rupdev Market, Deviganj Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300 Email- bhajan [email protected]

Sub :- Rate Contract for the supply of Item - RCC HUME PIPE (Valid From dated 31-03-2015 to 01-04-2016) Ref :- (I) This Office Tender Enquiry No. PS-VII/CSIDC/MKD/102/510/14-15

(II) Bid No. 8409 Dated 08-11-2014 (III) Your Offer acceptance alongwith undertaking submitted on dated 20-03-2015

Dear Sir, You are hereby informed that your above referred tender read with subsequent letters mentioned above for the Stores specified in the Schedules annexed has been accepted. This Rate Contract will be governed by the terms and conditions brought in CSIDC Form No.1 & 2. The Rate Contract and the Schedules annexed hereto shall be the sole repository of this Rate Contract / Transaction. You are required to show the original INK-SIGNED subject Rate Contract to the satisfaction of Direct Demanding Officer who will place the supply order as per instructions contained in CSIDC form No. 2 and also to the Quality Assurance Officer for inspection purpose and to the Paying Authority at the time of getting the payment. SCHEDULES ANNEXED: 1. Schedule “A” Description of Stores, Prices, Duties/Taxes . 2. Annexure -“A” Technical Particulars of Item- RCC HUME PIPE 3. Schedule “B” Special conditions of contract (if any). 4. Schedule “C” Information to DDOs about parallel rate contracts. 5. Schedule “D” Format for Drawal Report. Encl. 13 pages

Yours faithfully,


For and on behalf of the purchaser Named in CSIDC Form No.2

No. 5/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .

2. The Registrar, Honourable High court Chhattisgarh, Bilaspur .

3. The Accountant General Chhattisgarh State, Raipur.

4. All HODs of Chhattisgarh Govt. with a request to circulate the copy of R/C to all Direct Demanding Officers of your institution against issue of purchase order (Indent) in Favour of Rate Contract Holders of CSIDC.

5. All Collectors, Chhattisgarh State against issue of purchase order (Indent) in Favour of Rate Contract holders of CSIDC.

6. The Director Treasury, Chhattisgarh Govt., Raipur with a request to circulate copy of R/C to all branches under your control .

7. (i) Director of Public Instruction Department Pension Bada Raipur (ii) Engineer in Chief PHED C.G. Neer Bhawan, Raipur (iii) The Commissioner , Local Administrator , RDA Building Raipur (iv) Engineer in Chief PWD C.G.Civil lines Raipur .

Sr. No. 1 to 7 above are requested to call for original INK-SIGNED Rate Contract for verification to their full satisfaction including validity of various documents like Registration, Tax Registration etc. before taking action i.e. against issue of purchase order in Favour of Rate Contract holders of CSIDC, pre dispatched inspection of stores, acceptance of store.

8. (i) Dy.Director (Q.A.) , DGS&D, Bhilai, Durg (C.G.). (ii) Manager (Operation) Indian Register of Shipping, Senior MIG-2, Secter A, 1st Floor,

Infront of Bank of India Indrapuri Bhopal. (iii) Chief Engineer, PDIL, 4th floor, 4/2 Karaya Road, 67 Shekespeare Sarani, Kolkata (W.B.) (iv) General Manager (Inspection) RITES Ltd., Church gate Station Road, Second Floor, M.K.

Road, Mumbai-400020 (v) Operations Manager SGS India Pvt, Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal (MP)-

462011. above (i) to (v) are requested to call for original INK-SIGNED Rate Contract For Verification to their full satisfaction including validity of various documents like Validity of Registration, BIS Registration etc. before taking action i.e. inspection of stores, as the responsibility rests with the concerned authority. For information and necessary action against Authorized Inspection Agency accorded by CSIDC for inspection of stores.

9. Incharge, Monitoring Cell, MKT-1 CSIDC, Ltd. Raipur for necessary action against inspection of stores . 10. Manager (Tender), Marketing Div., CSIDC Ltd., Raipur. He is requested to maintain a master file

of Rate Contract. 11. Computer cell, CSIDC Ltd., Raipur to release Rate Contract on CSIDC website.

12. Main file of Item- RCC HUME PIPE


No. 6/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015

SCHEDULE “A” Description of Stores, Prices, Duties/Taxes

For the supply of Item- RCC HUME PIPE as per Annexure’A’ enclosed.

1. (a) NAME AND FULL ADDRESS OF :- M/s Aditya Industries, THE FIRM C/o Dhansiram Bhajankumar, Rupdev Market,

Deviganj Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300 Email- bhajan [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Aditya Industries, MANUFACTURER C/o Dhansiram Bhajankumar, Rupdev Market,


(C) Category :- General 2. VALIDITY OF RATE CONTRACT :- From 31-03-2015 To 01-04-2016 3. DESCRIPTION OF ITEM- RCC HUME PIPE SPECIFICATION, UNIT RATE AS BELOW

S.No. Item Code No. Item Description Class Rate ( )

E.D. VAT/CST Extra As Applicable

Rate Per Meter

Schedule -1: Reinforced Concrete, Light duty, Non-Pressure Pipes, Class: NP2, with ends of the Pipes suitable for collar joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm.

1 RCCHPF80001003 150 208.95 2 RCCHPF80001008 350 350.52 3 RCCHPF80001010 450 449.06

4 RCCHPF80001012 600 760.91 Schedule -3: Reinforced Concrete, Medium duty, Non-Pressure Pipes, Class: NP3, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm.

5 RCCHPF80001045 150 183.37 6 RCCHPF80001049 300 309.35 7 RCCHPF80001050 350 415.80 8 RCCHPF80001051 400 462.00 9 RCCHPF80001052 450 1050.00

10 RCCHPF80001053 500 1155.00 11 RCCHPF80001054 600 1480.50 12 RCCHPF80001055 700 1680.00 13 RCCHPF80001056 800 2250.00 14 RCCHPF80001057 900 2936.38 15 RCCHPF80001058 1000 3052.39 16 RCCHPF80001059 1100 3465.00 17 RCCHPF80001060 1200 4378.50

(Suresh Keshi)

General Manager


Schedule -5: Reinforced Concrete, Heavy duty, Non-Pressure Pipes, Class: NP4, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm.

18 RCCHPF80001087 150 202.08 19 RCCHPF80001091 300 415.80 20 RCCHPF80001092 350 462.00 21 RCCHPF80001093 400 485.10 22 RCCHPF80001094 450 1037.84 23 RCCHPF80001095 500 1239.91 24 RCCHPF80001096 600 1386.00 25 RCCHPF80001097 700 1732.50 26 RCCHPF80001099 900 2772.00 27 RCCHPF80001100 1000 3291.75 28 RCCHPF80001101 1100 3407.25 29 RCCHPF80001102 1200 4389.00

Schedule - 7 Transportation Charges : Sub Item Code No. Item Description Distance in Km. Transportation Charges in % on the Total Cost of Pipes/Collars.

E.D. VAT/CST Extra 30 RCCHPF80001148 Upto 50 Km. 19.64 31 RCCHPF80001149 Above 50 Km. Upto 100 Km. 21.00 32 RCCHPF80001150 Above 100 Km. Upto 150 Km. 28.88 33 RCCHPF80001151 Above 150 Km. Upto 200 Km. 32.00 34 RCCHPF80001152 Above 200 Km. 37.00

Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable

TIN No. 22425003108 Address:-

M/s Aditya Industries, C/o Dhansiram Bhajankumar, Rupdev Market, Deviganj Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300 Email- bhajan [email protected]

7. DELIVERY PERIOD : 30 Days 8. a. ANNUAL TURN OVER/ : 2010-11 Rs. 12329000.00

2011-12 Rs. 9064000.00 2012-13 Rs. 25628709.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Ambikapur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 5000 Nos. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned.


No. 8/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER

12. STATUS OF RC HOLDING : SSI Unit

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Ambikapur DTIC DTIC EM Part- II 220021100111 Dated 19-02-2008

14 BIS LICENSE : Not Mentioned

15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding Officers (DDOs).

16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate .

17 INSPECTION AUTHORITY : Dy. Director (Q &A), DGS&D, Bhilai (C.G.) OR

Manager (Operation) Indian Register of Shipping Senior MIG-2, Secter A, 1st Floor, in front of Bank of India Indrapuri Bhopal. (M.P.)

OR Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)

OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K.Road, Mumbai-400020 (Mah) OR

Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)

OR CSIDC (DEPARTMENTAL TECHNICAL WING)

18 QUALITY ASSURANCE : Dy. Director (Q &A), DGS&D, Bhilai (C.G.) OR



OR


No. 9/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K.Road, Mumbai-400020 (Mah) OR



19. PLACE WHERE THE STORES Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Aditya Industries, INSPECTION C/o Dhansiram Bhajankumar, Rupdev Market,


20 INSPECTION CHARGES : 0.60% Inspection charges + Service Tax As Applicable to be

paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.

21. SECURITY DEPOSIT : As per General conditions of contract , CSIDC Form No. 1, Clause 7, the Purchaser / DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note : 1. Purchasing Departments / end user will ensure to sending the copy of every order to this office for Approval of inspection Agency against inspection of stores.

2. Purchasing Departments / end user will ensure to Pre Dispatch inspection of stores Through inspection agency in enlisted in the CSIDC Panel.

3. Purchasing Departments / end user will be responsible for insuring the Quality of accepted stores.

4. Purchasing Departments / end user shall be insure to obtained the central excise invoices of Manufacturer as mentioned in the Schedule-A vide sr. no. 1-B if excise duty Applicable to the Rate Contract Holder.

5. Purchasing Departments / end user shall be insure to execute the Integrity Pact between BUYER and BIDDER/SUPPLIEY in accordance with the letter vide no. 799/eq-l-/2013 New Raipur Dated 10-07-2013 and 243/ fo-@fu-@pkj@2013 New Raipur Dated 06-07-2013 issued by the Chief Secretary Govt. Of Chhattisgarh.



Annexure 'A' CSIDC/MKD/TECH/2014-15/14

TECHNICAL PARTICULARS OF R.C.C. HUME PIPES

TSC 15-10-2014

This Specification covers the requirements for Non-Pressure Reinforced Precast Concrete Pipes (Spun) used for culverts, sewers, irrigation etc.

The Concrete Pipes shall be conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment with regards to Design /Dimensions / Tolerances / Workmanship & Finish / Materials used for making the Pipes. The Pipes shall be manufactured by spinning process. The ends of the concrete pipes shall be suitable for flush joints or collar joints or suitable for Socket & Spigot, roll on joints or confined gasket joints as per the requirements of the purchaser.

The Pipes shall be of the following Sizes & Classification: Schedule- 1: Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2, with ends of the pipes suitable for collar joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment

Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800.

1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP2 shall be as per the Table 2 of IS: 458/2003(Fourth Revision), with up-to-date amendment. 2. Tenderers may also quote rates separately for the Collars. Dimensions and Design requirements of Reinforced Concrete Collars for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003, with up-to-date amendment. Schedule- 2: Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP2 shall be as per the Table 2 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP2 Class Pipes shall be as per Table 13 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment.

(K.N.K. Mishra) Incharge PS-VII

No. 11/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-

date amendment. Schedule- 5: Reinforced Concrete, Heavy duty, Non-pressure Pipes, Class: NP4, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800.

1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003 (Fourth Revision) with up-to-date amendment.

Schedule- 6: Reinforced Concrete, Heavy duty, Non-pressure Pipes, Class: NP4, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment.


No. 12/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.

Item Description Distance in km. Transportation Charges in % on the Total Cost of Pipes/ Collars

1 Upto 50 km. 2 Above 50 km. upto 100 km. 3 Above 100 km. upto 150 km. 4 Above 150 km. upto 200 km. 5 Above 200 km.

Inspection & Testing: As per prevailing practice, the following Review of Reports shall be carried out. Review of Reports: The following Reports shall be submitted to the Inspecting Officer at the time of Inspection for review: During manufacture, Compressive Strength Tests shall be conducted by the manufacturers on 150 mm Concrete Cubes in accordance with the relevant requirements of IS: 456/2000 with up-to-date amendment and IS: 516/1959 (Reaffirmed 1999) with up-to-date amendment , as stipulated in clause 5.5.3 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. The manufacturer shall submit the results of Compressive Strength Tests of Concrete Cubes made from the Concrete used for the pipes. Alternatively, if the manufacturers do not have the facilities for Compressive Strength Test on Concrete Cubes, they shall get the Test done at CSIDC laboratory at least once in a month and submit the report to the Inspecting Officer for review.


No. 13/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/AI/6467 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.

Recommended by Technical Specification Committee Dated 15-10-2014



SCHEDULE ‘B’ (SPECIAL CONDITION OF CONTRACT)

RCC HUME PIPE

This Rate Contract Will be governed by the terms & conditions laid down in

The CSIDC form No. 1 & 2



SCHEDULE – “D”

FORMAT FOR QUATERLY DRAWAL REPORT

Name of the Firm __________________ I- Jan-Mar Report No. __________________ II- Apr-June Rate Contract No. __________________ III- July-Sept. Date of Submission __________________ IV- Oct - Dec Total Position of Order against Rate Contract till the submission of Report. S.No. Name of

Department Quantity and Value of Orders Received (Rs.)

Quantity and Value of Orders Executed (Rs.)

Balance Quantity and Value to be Supplied (Rs.)

Reasons

Foot 1. Value indicate should be a) Value of orders received during the quarter-Rs.

Total value inclusive of all Taxes duties and incidental b) Value of orders supplied during the quarter-Rs. Charges

2. Nil report should also be Submitted.





Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015 To,

M/s Surguja Cement Pipe Industries, Manendragarh Road Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300, 9826956300 Email- bhajan [email protected]




Yours faithfully,



No. 17/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 18/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Surguja Cement Pipe Industries, THE FIRM Manendragarh Road Ambikapur

Distt.- Surguja (C.G.) 497001 Mo.- 9425256300, 9826956300 Email- bhajan [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Surguja Cement Pipe Industries,

MANUFACTURER Manendragarh Road Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300, 9826956300 Email- bhajan [email protected]




Rate Per Meter

Schedule -3: Reinforced Concrete, Medium duty, Non-Pressure Pipes, Class: NP3, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm.


4 RCCHPF80001051 400 462.00 5 RCCHPF80001052 450 1050.00 6 RCCHPF80001053 500 1155.00 7 RCCHPF80001054 600 1480.50 8 RCCHPF80001055 700 1680.00 9 RCCHPF80001056 800 2250.00 10 RCCHPF80001057 900 2936.38 11 RCCHPF80001058 1000 3052.39 12 RCCHPF80001059 1100 3465.00 13 RCCHPF80001060 1200 4378.50










M/s Surguja Cement Pipe Industries, Manendragarh Road Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9425256300, 9826956300 Email- bhajan [email protected]


2011-12 Rs. 8233000.00 2012-13 Rs. 10492539.00


1 R.C.C. Hume Pipe (NP2 & 3)

191175 Nos.

2 Irrigation Pipe 3 R.C.C. Septic Tank 4 Fencing Pole Chains & Stone 5 R.C.C. Boundary & K.M. Stone 6 R.C.C. Tree Guard & Singn Board 7 R.C.C. Pre Cost Canal Lining 8 Slab & Tiles 9 R.C.C. Pre Cost Structure

10 R.C.C. Fencing Poles & Cement Hollow Bricks



9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM


14 BIS LICENSE : Not Mentioned 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding

Officers (DDOs). 16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each

consignment there-of will be made after receipt and acceptance of the stores by the consignee/interim consignee in full and good condition within 20 days as per SPR rule No.11, if the bills are in order. In case of delay in payment without any reason the department will be liable to pay interest as per prevailing bank rate. Bills are to be submitted in the prescribed form of the paying authority of purchaser / indenter and are to be supported with inspection note issued by the inspector and consignee’s Receipt Certificate .










(Suresh Keshi)

General Manager

No. 21/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015 OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K.Road, Mumbai-400020 (Mah) OR



19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Surguja Cement Pipe Industries, INSPECTION Manendragarh Road Ambikapur

Distt.- Surguja (C.G.) 497001 Mo.- 9425256300, 9826956300 Email- bhajan [email protected]









(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 23/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 24/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 25/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SCPI/6468 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons





No. 28/336 Chhattisgarh State Industrial Development Corporation Limited



Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RH&SP/6469 Dated: 31-03-2015 To,

M/s Raigarh Hume & Spun Pipe, Near Stadium, Industrial Area Raigarh (C.G.) Mo.- 9300676323, 9301010290 Email- [email protected]




Yours faithfully,



No. 29/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RH&SP/6469 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 30/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RH&SP/6469 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Raigarh Hume & Spun Pipe, THE FIRM Near Stadium, Industrial Area Raigarh (C.G.)

Mo.- 9300676323, 9301010290 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Raigarh Hume & Spun Pipe,

MANUFACTURER Near Stadium, Industrial Area Raigarh (C.G.) Mo.- 9300676323, 9301010290 Email- [email protected]




Rate Per Meter


1 RCCHPF80001052 450 1050.00 2 RCCHPF80001053 500 1155.00 3 RCCHPF80001054 600 1480.50 4 RCCHPF80001055 700 1680.00 5 RCCHPF80001057 900 2936.38 6 RCCHPF80001058 1000 3052.39 7 RCCHPF80001060 1200 4378.50




E.D. VAT/CST Extra 13 RCCHPF80001148 Upto 50 Km. 19.64 14 RCCHPF80001149 Above 50 Km. Upto 100 Km. 21.00 15 RCCHPF80001150 Above 100 Km. Upto 150 Km. 28.88

(Suresh Keshi)

General Manager


16 RCCHPF80001151 Above 150 Km. Upto 200 Km. 32.00 17 RCCHPF80001152 Above 200 Km. 37.00



M/s Raigarh Hume & Spun Pipe, Near Stadium, Industrial Area Raigarh (C.G.) Mo.- 9300676323, 9301010290 Email- [email protected]


2012-13 Rs. 4352307.00 2013-14 Rs. 5681490.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raigarh DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 29052 CFT. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Raigarh DTIC DTIC EM Part- II 220041100343 Dated 20-12-2010


Officers (DDOs).







OR Station Road, Second Floor, M.K.Road, Mumbai-400020 (Mah) OR






OR General Manager (Inspection) RITES Ltd. Churchgate Station Road, Second Floor, M.K.Road, Mumbai-400020 (Mah)

OR Manager (Operations) SGS India Pvt. Ltd. 43, RR Arcade, Zone-2, MP Nagar, Bhopal-462011. (M.P.)


19. PLACE WHERE THE STORES : Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Raigarh Hume & Spun Pipe, INSPECTION Near Stadium, Industrial Area Raigarh (C.G.)


20 INSPECTION CHARGES : 0.60% Inspection charges + Service Tax As Applicable to be paid extra at the time of inspection to Quality Assurance Officer which will be billed by the unit along with bill of the material and will be reimbursed by the paying authority of DDO.



21. SECURITY DEPOSIT : As per General conditions of contract , CSIDC Form No. 1, Clause

7, the Purchaser / DDOs may require the contractor to furnish a security deposit which shall be made after issue of the acceptance of the supply order within the period specified by the purchaser / DDOs. Such security deposit shall not ordinarily exceed 3% . The security shall be in form of Demand Drafts issued by any of the Scheduled Commercial Banks. No other form of security is to be accepted. The security deposit amount is to be refunded after successful completion of the supply.

22. Special Note 1. Purchasing Departments / end user will ensure to sending the copy of every order to this office for Approval of inspection Agency against inspection of stores. 2. Purchasing Departments / end user will ensure to Pre

Dispatch inspection of stores Through inspection agency in enlisted in the CSIDC Panel.








TSC 15-10-2014







No. 35/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RH&SP/6469 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 36/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RH&SP/6469 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 37/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RH&SP/6469 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6470 Dated: 31-03-2015 To,

M/s Dhanshri & Company , Deviganj Road Ambikapur Surguja (C.G.) 497001 Mo.- 09425580211 Ph.- 07774-235611




Yours faithfully,



No. 41/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6470 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 42/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6470 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Dhanshri & Company , THE FIRM Deviganj Road Ambikapur Surguja (C.G.) 497001

Mo.- 09425580211 Ph.- 07774-235611

(b) NAME AND FULL ADDRESS OF :- M/s Dhanshri & Company , MANUFACTURER Deviganj Road Ambikapur Surguja (C.G.) 497001

Mo.- 09425580211 Ph.- 07774-235611 (C) Category :- General 2. VALIDITY OF RATE CONTRACT :- From 31-03-2015 To 01-04-2016 6. DESCRIPTION OF ITEM- RCC HUME PIPE SPECIFICATION, UNIT RATE AS BELOW



Rate Per Meter


1 RCCHPF80001002 100 104.78 2 RCCHPF80001003 150 208.95




17 RCCHPF80001044 100 130.98 18 RCCHPF80001045 150 183.37 19 RCCHPF80001046 200 264.45 20 RCCHPF80001047 225 275.68



21 RCCHPF80001048 250 309.35 22 RCCHPF80001049 300 309.35 23 RCCHPF80001052 450 1050.00 24 RCCHPF80001053 500 1155.00 25 RCCHPF80001054 600 1480.50 26 RCCHPF80001055 700 1680.00 27 RCCHPF80001056 800 2250.00 28 RCCHPF80001057 900 2936.38 29 RCCHPF80001058 1000 3052.39 30 RCCHPF80001059 1100 3465.00 31 RCCHPF80001060 1200 4378.50 32 RCCHPF80001061 1400 5911.43 33 RCCHPF80001062 1600 7045.31 34 RCCHPF80001063 1800 7793.75


35 RCCHPF80001086 100 149.69 36 RCCHPF80001087 150 202.08 37 RCCHPF80001088 200 302.61 38 RCCHPF80001089 225 324.32 39 RCCHPF80001090 250 374.22 40 RCCHPF80001091 300 415.80 41 RCCHPF80001094 450 1037.84 42 RCCHPF80001095 500 1239.91 43 RCCHPF80001096 600 1386.00 44 RCCHPF80001097 700 1732.50 45 RCCHPF80001098 800 1963.50 46 RCCHPF80001099 900 2772.00 47 RCCHPF80001100 1000 3291.75 48 RCCHPF80001102 1200 4389.00 49 RCCHPF80001103 1400 5313.00 50 RCCHPF80001104 1600 7507.50

Schedule -7: Reinforced Concrete Collar for Reinforced Concrete Light duty, Non-Pressure Pipes, Class: NP2, conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes. Class: NP2, Size (Nominal Diameter in mm.) is as per below:









M/s Dhanshri & Company , Deviganj Road Ambikapur Surguja (C.G.) 497001 Mo.- 09425580211 Ph.- 07774-235611

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM


1 R.C.C. HUME PIPE

123675 Nos.

2 R.C.C. Boundary & Km Stone 3 R.C.C. Sign Board Tree Guard 4 R.C.C. Canal Lining Slab & Tiles 5 R.C.C. Dust Bin & Septic Tank 6 R.C.C. Fencing Pole

9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER (Suresh Keshi)

General Manager

No. 45/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6470 Dated: 31-03-2015 12. STATUS OF RC HOLDING : SSI Unit

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Ambikapur DTIC DTIC EM Part- II 220021100108 Dated 19-02-2008 14 BIS LICENSE : Not Mentioned


















ARE TO BE OFFERED FOR M/s Dhanshri & Company , INSPECTION Deviganj Road Ambikapur Surguja (C.G.) 497001

Mo.- 09425580211 Ph.- 07774-235611












TSC 15-10-2014







No. 48/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6473 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-




(K.N.K. Mishra)

Incharge PS-VII

No. 49/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6470 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 50/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/D&C/6470 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015 To,

M/s Agrasen Concrete Products, Navagarh Road, Bemetara Distt- Durg (C.G.) Mo.- 9977700300




Yours faithfully,



No. 54/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 55/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Agrasen Concrete Products, THE FIRM Navagarh Road, Bemetara Distt- Durg (C.G.)

Mo.- 9977700300 (b) NAME AND FULL ADDRESS OF :- M/s Agrasen Concrete Products,

MANUFACTURER Navagarh Road, Bemetara Distt- Durg (C.G.) Mo.- 9977700300




Rate Per Meter


1 RCCHPF80001052 450 1050.00 2 RCCHPF80001054 600 1480.50

3 RCCHPF80001057 900 2936.38

4 RCCHPF80001058 1000 3052.39 5 RCCHPF80001060 1200 4378.50


E.D. VAT/CST Extra 6 RCCHPF80001148 Upto 50 Km. 19.64 7 RCCHPF80001149 Above 50 Km. Upto 100 Km. 21.00 8 RCCHPF80001150 Above 100 Km. Upto 150 Km. 28.88 9 RCCHPF80001151 Above 150 Km. Upto 200 Km. 32.00

10 RCCHPF80001152 Above 200 Km. 37.00 Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable


M/s Agrasen Concrete Products, Navagarh Road, Bemetara Distt- Durg (C.G.) Mo.- 9977700300




2011-12 Rs. 8079084.00 2012-13 Rs. 9735988.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Bemetara DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 20,000 Nos.

9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Bemetara DTIC DTIC EM Part- II 22/010/11/00513 Dated 04-04-2008









No. 57/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015 OR









19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Agrasen Concrete Products, INSPECTION Navagarh Road, Bemetara Distt- Durg (C.G.)

Mo.- 9977700300







TSC 15-10-2014







No. 60/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 61/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 62/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/ACP/6471 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015 To,

M/s Gopesh Cement Arts, Dayalband Bilaspur (C.G.) Mo.- 9300325947, 9827485186 Email- [email protected]




Yours faithfully,



No. 66/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 67/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Gopesh Cement Arts, THE FIRM Dayalband Bilaspur (C.G.)


(b) NAME AND FULL ADDRESS OF :- M/s Gopesh Cement Arts, MANUFACTURER Dayalband Bilaspur (C.G.)





Rate Per Meter


1 RCCHPF80001003 150 208.95 2 RCCHPF80001005 225 233.27 3 RCCHPF80001006 250 241.99 4 RCCHPF80001009 400 440.33 5 RCCHPF80001011 500 600.00 6 RCCHPF80001012 600 760.91 7 RCCHPF80001013 700 903.12 8 RCCHPF80001014 800 1307.27 9 RCCHPF80001015 900 1155.00 10 RCCHPF80001016 1000 1212.75 11 RCCHPF80001018 1200 1501.50 12 RCCHPF80001019 1400 3117.25 13 RCCHPF80001020 1600 3871.93 14 RCCHPF80001021 1800 4479.42



(Suresh Keshi)

General Manager




30 RCCHPF80001128 100 35.81 31 RCCHPF80001129 150 42.11 32 RCCHPF80001130 200 51.98 33 RCCHPF80001131 225 61.22 34 RCCHPF80001132 250 63.53 35 RCCHPF80001133 300 76.23 36 RCCHPF80001134 350 88.94 37 RCCHPF80001135 400 128.21 38 RCCHPF80001136 450 140.33 39 RCCHPF80001137 500 187.50 40 RCCHPF80001138 600 210.00 41 RCCHPF80001139 700 226.38 42 RCCHPF80001140 800 243.71 43 RCCHPF80001141 900 315.00 44 RCCHPF80001142 1000 378.99 45 RCCHPF80001144 1200 577.50 46 RCCHPF80001145 1400 735.00 47 RCCHPF80001146 1600 840.00 48 RCCHPF80001147 1800 1050.00



Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable


No. 69/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015 6. SALES TAX /VAT : Extra, as Applicable


M/s Gopesh Cement Arts, Dayalband Bilaspur (C.G.) Mo.- 9300325947, 9827485186 Email- [email protected]


2012-13 Rs. 7721883.00 2013-14 Rs. 7662998.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Bilaspur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 34560 Nos. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Bilaspur DTIC DTIC EM Part-II 220071200231 Dated 24-01-2009








OR

Chief Engineer, Project & Development India Ltd. 4st floor, 4/2 Karaya Road, 67 Shekespeare Sarani Kolkata (W.B.)







OR General Manager (Inspection) RITES Ltd. Churchgate

Station Road, Second Floor, M.K.Road, Mumbai-400020 (Mah)



19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Gopesh Cement Arts, INSPECTION Dayalband Bilaspur (C.G.)










TSC 15-10-2014







No. 73/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 74/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 75/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/GCA/6472 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015 To,

M/s Radheshyam Benishyam Kesary & Co., Dayalband Bilaspur (C.G.) Mo.- 9827167998 , 9300333354 Email- [email protected]




Yours faithfully,



No. 79/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 80/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Radheshyam Benishyam Kesary & Co., THE FIRM Dayalband Bilaspur (C.G.)


(b) NAME AND FULL ADDRESS OF :- M/s Radheshyam Benishyam Kesary & Co., MANUFACTURER Dayalband Bilaspur (C.G.)

Mo.- 9827167998 , 9300333354 Email- [email protected]



E.D. VAT/CST Extra As

Applicable Rate Per Meter


1 RCCHPF80001003 150 208.95 2 RCCHPF80001006 250 241.99 3 RCCHPF80001009 400 440.33 4 RCCHPF80001011 500 600.00 5 RCCHPF80001012 600 760.91 6 RCCHPF80001013 700 903.12 7 RCCHPF80001014 800 1307.27 8 RCCHPF80001015 900 1155.00 9 RCCHPF80001016 1000 1212.75 10 RCCHPF80001018 1200 1501.50 11 RCCHPF80001019 1400 3117.25 12 RCCHPF80001020 1600 3871.93 13 RCCHPF80001021 1800 4479.42





19 RCCHPF80001052 450 1050.00 20 RCCHPF80001053 500 1155.00 21 RCCHPF80001054 600 1480.50 22 RCCHPF80001055 700 1680.00 23 RCCHPF80001056 800 2250.00 24 RCCHPF80001057 900 2936.38 25 RCCHPF80001058 1000 3052.39 26 RCCHPF80001059 1100 3465.00 27 RCCHPF80001060 1200 4378.50 28 RCCHPF80001061 1400 5911.43 29 RCCHPF80001062 1600 7045.31 30 RCCHPF80001063 1800 7793.75


31 RCCHPF80001128 100 35.81 32 RCCHPF80001129 150 42.11 33 RCCHPF80001130 200 51.98 34 RCCHPF80001131 225 61.22 35 RCCHPF80001132 250 63.53 36 RCCHPF80001133 300 76.23 37 RCCHPF80001134 350 88.94 38 RCCHPF80001135 400 128.21 39 RCCHPF80001136 450 140.33 40 RCCHPF80001137 500 187.50 41 RCCHPF80001138 600 210.00 42 RCCHPF80001139 700 226.38 43 RCCHPF80001140 800 243.71 44 RCCHPF80001141 900 315.00 45 RCCHPF80001142 1000 378.99 46 RCCHPF80001143 1100 525.00 47 RCCHPF80001144 1200 577.50 48 RCCHPF80001145 1400 735.00 49 RCCHPF80001146 1600 840.00 50 RCCHPF80001147 1800 1050.00





No. 82/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015 6. SALES TAX /VAT : Extra, as Applicable


M/s Radheshyam Benishyam Kesary & Co., Dayalband Bilaspur (C.G.) Mo.- 9827167998, 9300333354 Email- [email protected]

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER : 2011-12 Rs. 8549590.00 2012-13 Rs. 9731137.00 2013-14 Rs. 9894925.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Bilaspur DTIC Registration Certificate) Description Capacity/Annum

1 Rcc Hume Pipe NP2, NP3, NP4 45510 Nos. 2 Rcc Hume Pipe Half Round


FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with DTIC Bilaspur DTIC EM PART-II 220071200230 Dated 23-01-2009



















ARE TO BE OFFERED FOR M/s Radheshyam Benishyam Kesary & Co., INSPECTION Dayalband Bilaspur (C.G.)



(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 86/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 87/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 88/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RBK&C/6473 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015 To,

M/s Bilaspur Cement Products, C/o Shri Sai Teles & Sanitary Main Road Tarwa Naka Bilaspur (C.G.) 495001 Mo.- 9425219302, 9893968974 Ph.-07752-410302




Yours faithfully,



No. 92/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 93/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Bilaspur Cement Products, THE FIRM C/o Shri Sai Teles & Sanitary Main Road

Tarwa Naka Bilaspur (C.G.) 495001 Mo.- 9425219302, 9893968974 Ph.-07752-410302

(b) NAME AND FULL ADDRESS OF :- M/s Bilaspur Cement Products, MANUFACTURER C/o Shri Sai Teles & Sanitary Main Road





Rate Per Meter



4 RCCHPF80001018 1200 1501.50 5 RCCHPF80001019 1400 3117.25


6 RCCHPF80001049 300 309.35 7 RCCHPF80001052 450 1050.00 8 RCCHPF80001054 600 1480.50 9 RCCHPF80001057 900 2936.38 10 RCCHPF80001058 1000 3052.39 11 RCCHPF80001060 1200 4378.50











6. SALES TAX /VAT : Extra, as Applicable TIN No. 22394300893 Address:-

M/s Bilaspur Cement Products, C/o Shri Sai Teles & Sanitary Main Road Tarwa Naka Bilaspur (C.G.) 495001 Mo.- 9425219302, 9893968974 Ph.-07752-410302

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Bilaspur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 15,000 Nos. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER


No. 95/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015 12. STATUS OF RC HOLDING : Manufacturer

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Bilaspur DTIC DTIC EM Part- II 220071100886 Dated 05-06-2013
















(Suresh Keshi)

General Manager



ARE TO BE OFFERED FOR M/s Bilaspur Cement Products, INSPECTION C/o Shri Sai Teles & Sanitary Main Road













TSC 15-10-2014







No. 98/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 99/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 100/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/BCP/6474 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 To,

M/s Vasudev Shamji Savaria, Bajirao Mehrapara Raigarh (C.G.) 496001 Ph.- 07762-220050 Mo.- 099267-42045 Email- [email protected]




Yours faithfully,



No. 104/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 105/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Vasudev Shamji Savaria Bajirao, THE FIRM Mehrapara Raigarh (C.G.) 496001

Ph.- 07762-220050 Mo.- 099267-42045 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Vasudev Shamji Savaria Bajirao,

MANUFACTURER Mehrapara Raigarh (C.G.) 496001 Ph.- 07762-220050 Mo.- 099267-42045 Email- [email protected]




Rate Per Meter







(Suresh Keshi)

General Manager

No. 106/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable


M/s Vasudev Shamji Savaria Bajirao, Mehrapara Raigarh (C.G.) 496001 Ph.- 07762-220050 Mo.- 099267-42045 Email- [email protected]


2012-13 Rs. 4023700.00 2013-14 Rs. 5221400.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raigarh DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 42213 CFT.

9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Raigarh DTIC DTIC EM Part- II 220041100341 Dated 14-12-2010





No. 107/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 17 INSPECTION AUTHORITY : Dy. Director (Q &A), DGS&D, Bhilai (C.G.) OR












19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Vasudev Shamji Savaria Bajirao, INSPECTION Mehrapara Raigarh (C.G.) 496001

Ph.- 07762-220050 Mo.- 099267-42045 Email- [email protected]


(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 110/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 111/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 112/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/VSS/6475 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons







Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 To,

M/s Dinesh Industries, Telibandha, Near Gali No.- 6 Ravigram,

Ph.- 0771-3265888 Mo.- 9755042331, 9926156001 Sub :- Rate Contract for the supply of Item - RCC HUME PIPE (Valid From dated 31-03-2015 to 01-04-2016) Ref :- (I) This Office Tender Enquiry No. PS-VII/CSIDC/MKD/102/510/14-15



Yours faithfully,



No. 116/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 117/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Dinesh Industries, THE FIRM Telibandha, Near Gali No.- 6 Ravigram,

Ph.- 0771-3265888 Mo.- 9755042331, 9926156001 (b) NAME AND FULL ADDRESS OF :- M/s Dinesh Industries,

MANUFACTURER Plot No. 730 A Industrial Estate Urla Raipur (C.G.) 492001 Ph.- 0771-3265888

Mo.- 9755042331, 9926156001 (C) Category :- General 2. VALIDITY OF RATE CONTRACT :- From 31-03-2015 To 01-04-2016 12. DESCRIPTION OF ITEM- RCC HUME PIPE SPECIFICATION, UNIT RATE AS BELOW



Rate Per Meter




8 RCCHPF80001095 500 1239.91 Schedule - 7 Transportation Charges : Sub Item Code No. Item Description Distance in Km. Transportation Charges in % on the Total Cost of Pipes/Collars.

E.D. VAT/CST Extra 9 RCCHPF80001148 Upto 50 Km. 19.64

10 RCCHPF80001149 Above 50 Km. Upto 100 Km. 21.00 11 RCCHPF80001150 Above 100 Km. Upto 150 Km. 28.88 12 RCCHPF80001151 Above 150 Km. Upto 200 Km. 32.00 13 RCCHPF80001152 Above 200 Km. 37.00

Note :- Technical particulars as per Annexure A enclosed


No. 118/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable


M/s Dinesh Industries, Telibandha, Near Gali No.- 6 Ravigram,

Ph.- 0771-3265888 Mo.- 9755042331, 9926156001 7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raipur DTIC Registration Certificate) Description Capacity/Annum

1 RCC Hume Pipes

180000 CU.FT.

2 Water Tanks 3 Septic Tanks 4 Dust Bins 5 Fencing Poles 6 Precast Cocrete Slabs 7 Kilometre Stone & Boundary Stone

9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Raipur DTIC DTIC EM Part- II 220111102154 Dated 18-11-2014


Officers (DDOs).



16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each















ARE TO BE OFFERED FOR M/s Dinesh Industries, INSPECTION Telibandha, Near Gali No.- 6 Ravigram,

Raipur Factory 730 A Industrial Estate Urla Raipur (C.G.) 492001 Ph.- 0771-3265888

Mo.- 9755042331, 9926156001


No. 120/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 20 INSPECTION CHARGES : 0.60% Inspection charges + Service Tax As Applicable to be












TSC 15-10-2014







No. 122/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 123/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 124/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DI/6476 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015 To,

M/s Quality Cement Pipes, Add : 11,12 Industrial Estate Bhanpuri Raipur (C.G.) 493221 Ph.- 0771-4024190 Mo.- 9752005557




Yours faithfully,



No. 128/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 129/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Quality Cement Pipes, THE FIRM Add : 11,12 Industrial Estate

Bhanpuri Raipur (C.G.) 493221 Ph.-0771-4024190 Mo.- 9752005557

(b) NAME AND FULL ADDRESS OF :- M/s Quality Cement Pipes,

MANUFACTURER Add : 11,12 Industrial Estate Bhanpuri Raipur (C.G.) 493221 Ph.-0771-4024190 Mo.- 9752005557



E.D. VAT/CST Extra As

Applicable Rate Per Meter




8 RCCHPF80001088 200 302.61 9 RCCHPF80001089 225 324.32

10 RCCHPF80001090 250 374.22 11 RCCHPF80001095 500 1239.91




No. 130/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015 Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable


M/s Quality Cement Pipes, Add : 11,12 Industrial Estate Bhanpuri Raipur (C.G.) 493221 Ph.-0771-4024190 Mo.- 9752005557


2011-12 Rs. 11954369.00 2012-13 Rs. 11492873.75

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raipur DTIC Registration Certificate) Description Capacity/Annum

1 R.C.C. Hume Pipe

80,000 CFT. 2 R.C.C. Fencing Pole 3 R.C.C. Kilometer Stone 4 R.C.C. Boundary Stone 5 R.C.C. Water Septic Tank


FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Durg Raipur DTIC EM Part- II 220111100941 16-07-2009




















ARE TO BE OFFERED FOR M/s Quality Cement Pipes, INSPECTION Add : 11,12 Industrial Estate

Bhanpuri Raipur (C.G.) 493221 Ph.-0771-4024190 Mo.- 9752005557





TSC 15-10-2014







No. 134/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 135/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 136/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/QCP/6477 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons





No. 139/336 eS Chhattisgarh State Industrial Development Corporation Limited



Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015 To,

M/s Raj Pipes, Infront of Industrial Estate, G.E. Road, Rajnandgaon (C.G.)




Yours faithfully,



No. 140/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 141/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Raj Pipes, THE FIRM Infront of Industrial Estate,

G.E. Road, Rajnandgaon (C.G.)

(b) NAME AND FULL ADDRESS OF :- M/s Raj Pipes, MANUFACTURER Infront of Industrial Estate,





Rate Per Meter


1 RCCHPF80001012 600 760.91 2 RCCHPF80001013 700 903.12




7 RCCHPF80001138 600 210.00 8 RCCHPF80001139 700 226.38





No. 142/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable

TIN No. 22223601665

Address:- M/s Raj Pipes, Infront of Industrial Estate, G.E. Road, Rajnandgaon (C.G.)


2012-13 Rs. 5114377.00 2013-14 Rs. 5849512.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Rajnandgaon DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 5000 RFT. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Rajnandgaon DTIC DTIC EM Part-II 220091100306 Dated 16-12-2010


















19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Raj Pipes, INSPECTION Infront of Industrial Estate,



(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 146/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 147/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 148/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/RP/6478 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/API/6479 Dated: 31-03-2015 To,

M/s Akash Pipe Industries, Dharampara Mungeli Bilaspur (C.G.) 495334 Mo.- 9993070099




Yours faithfully,



No. 152/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/API/6479 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 153/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/API/6479 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Akash Pipe Industries, THE FIRM Dharampara Mungeli Bilaspur (C.G.) 495334

Mo.- 9993070099 (b) NAME AND FULL ADDRESS OF :- M/s Akash Pipe Industries,

MANUFACTURER Dharampara Mungeli Bilaspur (C.G.) 495334 Mo.- 9993070099




Rate Per Meter





Schedule -2: Reinforced Concrete, Light duty, Non-Pressure Pipes, Class: NP2, with ends of the Pipes Suitable for Socket & Spigot, roll & joints or confined gasket joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm.



20 RCCHPF80001022 80 32.49 21 RCCHPF80001023 100 35.81 22 RCCHPF80001024 150 42.11 23 RCCHPF80001025 200 51.98 24 RCCHPF80001026 225 61.22 25 RCCHPF80001027 250 63.53 26 RCCHPF80001028 300 76.23 27 RCCHPF80001029 350 88.94 28 RCCHPF80001030 400 128.21 29 RCCHPF80001031 450 140.33 30 RCCHPF80001032 500 187.50 31 RCCHPF80001033 600 217.14 32 RCCHPF80001034 700 226.38 33 RCCHPF80001035 800 243.71 34 RCCHPF80001036 900 360.94 35 RCCHPF80001037 1000 378.99 36 RCCHPF80001038 1100 577.50 37 RCCHPF80001039 1200 706.86 38 RCCHPF80001040 1400 974.14 39 RCCHPF80001041 1600 1099.56 40 RCCHPF80001042 1800 1398.71


41 RCCHPF80001043 80 106.59 42 RCCHPF80001044 100 130.98 43 RCCHPF80001045 150 183.37 44 RCCHPF80001046 200 264.45 45 RCCHPF80001047 225 275.68 46 RCCHPF80001048 250 309.35 47 RCCHPF80001049 300 309.35 48 RCCHPF80001050 350 415.80 49 RCCHPF80001051 400 462.00 50 RCCHPF80001052 450 1050.00 51 RCCHPF80001053 500 1155.00 52 RCCHPF80001054 600 1480.50 53 RCCHPF80001055 700 1680.00 54 RCCHPF80001056 800 2250.00 55 RCCHPF80001057 900 2936.38 56 RCCHPF80001058 1000 3052.39 57 RCCHPF80001059 1100 3465.00 58 RCCHPF80001060 1200 4378.50 59 RCCHPF80001061 1400 5911.43 60 RCCHPF80001062 1600 7045.31 61 RCCHPF80001063 1800 7793.75


(Suresh Keshi)

General Manager


62 RCCHPF80001085 80 128.48 63 RCCHPF80001086 100 149.69 64 RCCHPF80001087 150 202.08 65 RCCHPF80001088 200 302.61 66 RCCHPF80001089 225 324.32 67 RCCHPF80001090 250 374.22 68 RCCHPF80001091 300 415.80 69 RCCHPF80001092 350 462.00 70 RCCHPF80001093 400 485.10 71 RCCHPF80001094 450 1037.84 72 RCCHPF80001095 500 1239.91 73 RCCHPF80001096 600 1386.00 74 RCCHPF80001097 700 1732.50 75 RCCHPF80001098 800 1963.50 76 RCCHPF80001099 900 2772.00 77 RCCHPF80001100 1000 3291.75 78 RCCHPF80001101 1100 3407.25 79 RCCHPF80001102 1200 4389.00 80 RCCHPF80001103 1400 5313.00 81 RCCHPF80001104 1600 7507.50


82 RCCHPF80001127 80 31.50 83 RCCHPF80001128 100 35.81 84 RCCHPF80001129 150 42.11 85 RCCHPF80001130 200 51.98 86 RCCHPF80001131 225 61.22 87 RCCHPF80001132 250 63.53 88 RCCHPF80001133 300 76.23 89 RCCHPF80001134 350 88.94 90 RCCHPF80001135 400 128.21 91 RCCHPF80001136 450 140.33 92 RCCHPF80001137 500 187.50 93 RCCHPF80001138 600 210.00 94 RCCHPF80001139 700 226.38 95 RCCHPF80001140 800 243.71 96 RCCHPF80001141 900 315.00 97 RCCHPF80001142 1000 378.99 98 RCCHPF80001143 1100 525.00 99 RCCHPF80001144 1200 577.50








M/s Akash Pipe Industries, Dharampara Mungeli Bilaspur (C.G.) 495334 Mo.- 9993070099


b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Mungeli DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 6000 Nos.


FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Mungeli DTIC DTIC EM Part- II 220071100292 Dated 06-10-2009



















19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Akash Pipe Industries, INSPECTION Dharampara Mungeli Bilaspur (C.G.) 495334

Mo.- 9993070099

(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 160/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/API/6479 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 161/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/API/6479 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 162/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/API/6479 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015 To,

M/s Korba Cement Products, Urga-Korba (C.G.) Mo.- 9425224499 Email- [email protected]




Yours faithfully,



No. 166/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 167/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Korba Cement Products, THE FIRM Urga-Korba (C.G.)

Mo.- 9425224499 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Korba Cement Products,

MANUFACTURER Urga-Korba (C.G.) Mo.- 9425224499 Email- [email protected]




Rate Per Meter


1 RCCHPF80001003 150 208.95










42 RCCHPF80001129 150 42.11 43 RCCHPF80001130 200 51.98 44 RCCHPF80001132 250 63.53 45 RCCHPF80001133 300 76.23 46 RCCHPF80001134 350 88.94 47 RCCHPF80001135 400 128.21 48 RCCHPF80001136 450 140.33 49 RCCHPF80001137 500 187.50 50 RCCHPF80001138 600 210.00 51 RCCHPF80001141 900 315.00 52 RCCHPF80001142 1000 378.99 53 RCCHPF80001144 1200 577.50 54 RCCHPF80001145 1400 735.00 55 RCCHPF80001146 1600 840.00 56 RCCHPF80001147 1800 1050.00


E.D. VAT/CST Extra 57 RCCHPF80001148 Upto 50 Km. 19.64

(Suresh Keshi)

General Manager


58 RCCHPF80001149 Above 50 Km. Upto 100 Km. 21.00 59 RCCHPF80001150 Above 100 Km. Upto 150 Km. 28.88 60 RCCHPF80001151 Above 150 Km. Upto 200 Km. 32.00 61 RCCHPF80001152 Above 200 Km. 37.00



M/s Korba Cement Products, Urga-Korba (C.G.) Mo.- 9425224499 Email- [email protected]


2012-13 Rs. 15225481.00 2013-14 Rs. 18343743.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Korba DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 1200 Nos. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Korba DTIC DTIC EM Part- II 220051100146 Dated 10-06-2009




No. 170/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015 16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each














19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Korba Cement Products, INSPECTION Urga-Korba (C.G.)

Mo.- 9425224499 Email- [email protected]





TSC 15-10-2014







No. 173/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 174/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 175/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/KCP/6480 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015 To,

M/s Dhansree Concrete Products , Manendragarh Road Ambikapur (C.G.) 497001 Mo.- 9425580211




Yours faithfully,



No. 179/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 180/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Dhansree Concrete Products , THE FIRM Manendragarh Road Ambikapur (C.G.) 497001

Mo.- 9425580211

(b) NAME AND FULL ADDRESS OF :- M/s Dhansree Concrete Products , MANUFACTURER Manendragarh Road Ambikapur (C.G.) 497001

Mo.- 9425580211 (C) Category :- General 2. VALIDITY OF RATE CONTRACT :- From 31-03-2015 To 01-04-2016 17. DESCRIPTION OF ITEM- RCC HUME PIPE SPECIFICATION, UNIT RATE AS BELOW



Rate Per Meter


1 RCCHPF80001012 600 760.91 Schedule -3: Reinforced Concrete, Medium duty, Non-Pressure Pipes, Class: NP3, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm.



Schedule -5: Reinforced Concrete, Heavy duty, Non-Pressure Pipes, Class: NP4, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm. 14 RCCHPF80001094 450 1037.84 15 RCCHPF80001095 500 1239.91 16 RCCHPF80001096 600 1386.00 17 RCCHPF80001097 700 1732.50




Schedule -7: Reinforced Concrete Collar for Reinforced Concrete Light duty, Non-Pressure Pipes, Class: NP2, conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes. Class: NP2, Size (Nominal Diameter in mm.) is as per below: 24 RCCHPF80001138 600 210.00





M/s Dhansree Concrete Products , Manendragarh Road Ambikapur (C.G.) 497001 Mo.- 9425580211

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Ambikapur DTIC Registration Certificate) Description Capacity/Annum


FIRM



13. REGISTRATION STATUS : Manufacturer is Registered with Ambikapur DTIC DTIC EM Part-II 220021100110 Dated 19-02-2008 14 BIS LICENSE : Not Mentioned 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding
















No. 183/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015 19. PLACE WHERE THE STORES Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Dhansree Concrete Products , INSPECTION Manendragarh Road Ambikapur (C.G.) 497001

Mo.- 9425580211












TSC 15-10-2014







No. 185/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 186/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 187/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/DCP/6481 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons





No. 190/336 rS Chhattisgarh State Industrial Development Corporation Limited



Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015 To,

M/s Shivshakti Industries, Kena Bandh Bouripara, Ambikapur, Distt Surguja (C.G.) 497001 Mo.-9425582023-24




Yours faithfully,



No. 191/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 192/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Shivshakti Industries, THE FIRM Kena Bandh Bouripara,

Ambikapur, Distt Surguja (C.G.) 497001 Mo.-9425582023-24

(b) NAME AND FULL ADDRESS OF :- M/s Shivshakti Industries, MANUFACTURER Kena Bandh Bouripara,





Rate Per Meter



4 RCCHPF80001058 1000 3052.39 5 RCCHPF80001060 1200 4378.50





Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State)


No. 193/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015 5. EXCISE DUTY : Not Applicable

6. SALES TAX /VAT : Extra, as Applicable


M/s Shivshakti Industries, Kena Bandh Bouripara, Ambikapur, Distt Surguja (C.G.) 497001 Mo.-9425582023-24

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Ambikapur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 9500 Nos. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM









OR











19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Shivshakti Industries, INSPECTION Kena Bandh Bouripara,









TSC 15-10-2014







No. 197/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 198/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 199/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/14-15/RCCHP/SI/6482 Dated: 31-03-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 To,

M/s Jai Mahamaya Cement Pipe Industries, Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 Email- [email protected]




Yours faithfully,



No. 203/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 204/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Jai Mahamaya Cement Pipe Industries, THE FIRM Mission Chowk, Ring Road,

Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Jai Mahamaya Cement Pipe Industries,

MANUFACTURER Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 Email- [email protected]


S.No. Item Code No. Item Description Class Rate ( ) E.D. VAT/CST

Extra As Applicable Rate Per Meter




6 RCCHPF80001024 150 42.11 7 RCCHPF80001025 200 51.98 8 RCCHPF80001028 300 76.23 9 RCCHPF80001031 450 140.33 10 RCCHPF80001033 600 217.14 11 RCCHPF80001035 800 243.71 12 RCCHPF80001036 900 360.94 13 RCCHPF80001037 1000 378.99 14 RCCHPF80001039 1200 706.86

(Suresh Keshi)

General Manager



15 RCCHPF80001045 150 183.37 16 RCCHPF80001046 200 264.45 17 RCCHPF80001047 225 275.68 18 RCCHPF80001048 250 309.35 19 RCCHPF80001049 300 309.35 20 RCCHPF80001050 350 415.80 21 RCCHPF80001051 400 462.00 22 RCCHPF80001052 450 1050.00 23 RCCHPF80001053 500 1155.00 24 RCCHPF80001054 600 1480.50 25 RCCHPF80001055 700 1680.00 26 RCCHPF80001056 800 2250.00 27 RCCHPF80001057 900 2936.38 28 RCCHPF80001058 1000 3052.39 29 RCCHPF80001059 1100 3465.00 30 RCCHPF80001060 1200 4378.50 31 RCCHPF80001061 1400 5911.43 32 RCCHPF80001062 1600 7045.31 33 RCCHPF80001063 1800 7793.75






TIN No. 22715002803



Address:-

M/s Jai Mahamaya Cement Pipe Industries, Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 Email- [email protected]


2012-13 Rs. 13915642.00 2013-14 Rs. 18206139.00



FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Ambikapur DTIC DTIC EM Part- II 220021100117 Dated 25-02-2008




(Suresh Keshi)

General Manager

No. 207/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 17 INSPECTION AUTHORITY : Dy. Director (Q &A), DGS&D, Bhilai (C.G.) OR













ARE TO BE OFFERED FOR M/s Jai Mahamaya Cement Pipe Industries, INSPECTION Mission Chowk, Ring Road,

Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 Email- [email protected]



No. 208/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 21. SECURITY DEPOSIT : As per General conditions of contract , CSIDC Form No. 1, Clause











TSC 15-10-2014







No. 210/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 211/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 212/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JMCPI/6483 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 To,

M/s Jai Ambe Cement Product, Vill-Sargawan, Teh.-Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358, 9425254259




Yours faithfully,



No. 216/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 217/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Jai Ambe Cement Product, THE FIRM Vill-Sargawan, Teh.-Ambikapur

Distt.- Surguja (C.G.) 497001 Mo.- 9826122358, 9425254259

(b) NAME AND FULL ADDRESS OF :- M/s Jai Ambe Cement Product, MANUFACTURER Vill-Sargawan, Teh.-Ambikapur





Rate Per Meter






15 RCCHPF80001045 150 183.37



16 RCCHPF80001046 200 264.45 17 RCCHPF80001047 225 275.68 18 RCCHPF80001048 250 309.35 19 RCCHPF80001049 300 309.35 20 RCCHPF80001050 350 415.80 21 RCCHPF80001051 400 462.00 22 RCCHPF80001052 450 1050.00 23 RCCHPF80001053 500 1155.00 24 RCCHPF80001054 600 1480.50 25 RCCHPF80001055 700 1680.00 26 RCCHPF80001056 800 2250.00 27 RCCHPF80001057 900 2936.38 28 RCCHPF80001058 1000 3052.39 29 RCCHPF80001059 1100 3465.00 30 RCCHPF80001060 1200 4378.50 31 RCCHPF80001061 1400 5911.43 32 RCCHPF80001062 1600 7045.31 33 RCCHPF80001063 1800 7793.75







M/s Jai Ambe Cement Product, Vill-Sargawan, Teh.-Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358, 9425254259

(Suresh Keshi)

General Manager

No. 219/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 7. DELIVERY PERIOD : 30 Days 8. a. ANNUAL TURN OVER/ : 2011-12 Rs. 12310958.00

2012-13 Rs. 10787348.00 2013-14 Rs. 13846409.00


RCC HUME PIPE 15,000 Nos.


FIRM










No. 220/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 OR


OR CSIDC (DEPARTMENTAL TECHNICAL WING) 18 QUALITY ASSURANCE : Dy. Director (Q &A), DGS&D, Bhilai (C.G.) OR






19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Jai Ambe Cement Product, INSPECTION Vill-Sargawan, Teh.-Ambikapur








TSC 15-10-2014







No. 223/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 224/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 225/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JACP/6484 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JCP/6485 Dated: 10-04-2015 To,

M/s Jaiswal Cement Products, Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 / 9425254259 Email- [email protected]




Yours faithfully,



No. 229/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JCP/6485 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 230/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JCP/6485 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Jaiswal Cement Products, THE FIRM Mission Chowk, Ring Road,

Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 / 9425254259 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Jaiswal Cement Products,

MANUFACTURER Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 / 9425254259 Email- [email protected]




Rate Per Meter








Schedule -3: Reinforced Concrete, Medium duty, Non-Pressure Pipes, Class: NP3, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm. 15 RCCHPF80001045 150 183.37 16 RCCHPF80001046 200 264.45 17 RCCHPF80001047 225 275.68 18 RCCHPF80001048 250 309.35 19 RCCHPF80001049 300 309.35 20 RCCHPF80001050 350 415.80 21 RCCHPF80001051 400 462.00 22 RCCHPF80001052 450 1050.00 23 RCCHPF80001053 500 1155.00 24 RCCHPF80001054 600 1480.50 25 RCCHPF80001055 700 1680.00 26 RCCHPF80001056 800 2250.00 27 RCCHPF80001057 900 2936.38 28 RCCHPF80001058 1000 3052.39 29 RCCHPF80001059 1100 3465.00 30 RCCHPF80001060 1200 4378.50 31 RCCHPF80001061 1400 5911.43 32 RCCHPF80001062 1600 7045.31 33 RCCHPF80001063 1800 7793.75

Schedule -5: Reinforced Concrete, Heavy duty, Non-Pressure Pipes, Class: NP4, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm. 34 RCCHPF80001091 300 415.80 35 RCCHPF80001092 350 462.00 36 RCCHPF80001094 450 1037.84 37 RCCHPF80001096 600 1386.00 38 RCCHPF80001099 900 2772.00 39 RCCHPF80001100 1000 3291.75 40 RCCHPF80001102 1200 4389.00




TIN No. 22365001201



Address:-

M/s Jaiswal Cement Products, Mission Chowk, Ring Road, Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 / 9425254259 Email- [email protected]


2012-13 Rs. 11775619.00 2013-14 Rs. 14008858.00



FIRM



Officers (DDOs).


(Suresh Keshi)

General Manager














19. PLACE WHERE THE STORES : Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Jaiswal Cement Products, INSPECTION Mission Chowk, Ring Road,

Ambikapur Distt.- Surguja (C.G.) 497001 Mo.- 9826122358 / 9425254259 Email- [email protected]


(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 236/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JCP/6485 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 237/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JCP/6485 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 238/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/JCP/6485 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015 To,

M/s Bhilai Cement Pipe Manufacturing Co., 70-A, Industrial Estate, Nandini Road, Bhilai (C.G.) Ph.- 0788 - 2286518 Mo.- 9893115028, 9981125028




Yours faithfully,



No. 242/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 243/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Bhilai Cement Pipe Manufacturing co., THE FIRM 70-A,Industrial Estate,

Nandini Road, Bhilai (C.G.) Ph.- 0788-4050236, 2286518 Mo.- 9893115028, 9981125028

(b) NAME AND FULL ADDRESS OF :- M/s Bhilai Cement Pipe Manufacturing co.,

MANUFACTURER 70-A,Industrial Estate, Nandini Road, Bhilai (C.G.) Ph.- 0788-4050236, 2286518 Mo.- 9893115028, 9981125028




Rate Per Meter



4 RCCHPF80001058 1000 3052.39 5 RCCHPF80001060 1200 4378.50



10 RCCHPF80001152 Above 200 Km. 37.00 Note :- Technical particulars as per Annexure A enclosed 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable


No. 244/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015 6. SALES TAX /VAT : Extra, as Applicable


M/s Bhilai Cement Pipe Manufacturing co., 70-A,Industrial Estate, Nandini Road, Bhilai (C.G.) Ph.- 0788-4050236, 2286518 Mo.- 9893115028, 9981125028


b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Durg DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 35,000 RFT. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final.

11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Durg DTIC DTIC EM Part –II 220101100509 Dated 28-03-2008


Officers (DDOs).




OR














ARE TO BE OFFERED FOR M/s Bhilai Cement Pipe Manufacturing co., INSPECTION 70-A,Industrial Estate,

Nandini Road, Bhilai (C.G.) Ph.- 0788-4050236, 2286518 Mo.- 9893115028, 9981125028









TSC 15-10-2014







No. 248/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 249/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 250/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPMC/6486 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015 To,

M/s Bhawani Cement Pipe Industries, D-1, Om Complex, Fafadih Raipur (C.G.) 492001 Ph.- 07714092724 , Mo.- 9425507207




Yours faithfully,



No. 254/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 255/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Bhawani Cement Pipe Industries, THE FIRM D-1, Om Complex, Fafadih Raipur (C.G.) 492001

Ph.- 07714092724 , Mo.- 9425507207

(b) NAME AND FULL ADDRESS OF :- M/s Bhawani Cement Pipe Industries, MANUFACTURER Kh.No-521/9 (Part) & 522-4 (Part)

Village Deori Bilaspur Road Raipur (C.G.) 492001 Ph.- 07714092724 , Mo.- 9425507207




Rate Per Meter



10 RCCHPF80001062 1600 7045.31 11 RCCHPF80001063 1800 7793.75



(Suresh Keshi)

General Manager







6. SALES TAX /VAT : Extra, as Applicable TIN No. 22411504954 Address:-

M/s Bhawani Cement Pipe Industries, D-1, Om Complex, Fafadih Raipur (C.G.) 492001 Ph.- 07714092724 , Mo.- 9425507207

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raipur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 3000 R.M. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Raipur DTIC DTIC EM Part- II 220111100557 Dated 22-05-2008 14 BIS LICENSE : Not Mentioned



15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct Demanding
















No. 258/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015 19. PLACE WHERE THE STORES Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s Bhawani Cement Pipe Industries, INSPECTION Kh.No-521/9 (Part) & 522-4 (Part)

Village Deori Bilaspur Road Raipur (C.G.) 492001 Ph.- 07714092724 , Mo.- 9425507207














TSC 15-10-2014







No. 260/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 261/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 262/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCPI/6487 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCP/6488 Dated: 10-04-2015 To,

M/s Bastar Cement Products, Geedam Road, P.O Pandripani, Jagdalpur (Bastar) 494001 Mo.- 9826612012, 9425212012 Email- [email protected]




Yours faithfully,



No. 266/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCP/6488 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .



















1. (a) NAME AND FULL ADDRESS OF :- M/s Bastar Cement Products, THE FIRM Geedam Road, P.O Pandripani,

Jagdalpur (Bastar) 494001 Mo.- 9826612012, 9425212012 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Bastar Cement Products, MANUFACTURER Geedam Road, P.O Pandripani,





Rate Per Meter



Schedule -5: Reinforced Concrete, Heavy duty, Non-Pressure Pipes, Class: NP4, with ends of the Pipes Suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment Nominal Diameter of Pipes in mm. 10 RCCHPF80001094 450 1037.84 11 RCCHPF80001095 500 1239.91 12 RCCHPF80001096 600 1386.00 13 RCCHPF80001097 700 1732.50 14 RCCHPF80001098 800 1963.50 15 RCCHPF80001099 900 2772.00 16 RCCHPF80001100 1000 3291.75 17 RCCHPF80001102 1200 4389.00

(Suresh Keshi)

General Manager






M/s Bastar Cement Products, Geedam Road, P.O Pandripani, Jagdalpur (Bastar) 494001 Mo.- 9826612012, 9425212012 Email- [email protected]


b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Jagdalpur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 66175 CFT.


FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Jagdalpur DTIC DTIC EM Part- II 220151100115 Dated 12-03-2009

14 BIS LICENSE : Not Mentioned 15. PAYING AUTHORITY : As Mentioned in supply order to be issued by Direct

Demanding Officers (DDOs).


No. 269/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCP/6488 Dated: 10-04-2015 16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each














19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Bastar Cement Products, INSPECTION Geedam Road, P.O Pandripani,


(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 272/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCP/6488 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 273/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCP/6488 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 274/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/BCP/6488 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons





No. 277/336 0S Chhattisgarh State Industrial Development Corporation Limited



Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015 To,

M/s Engineers Enterprises, Rawabhata Industrial Area P.O. Birgaon Raipur (C.G.) 493221 Mo.- 9826612012, 9425212012 Email- [email protected]




Yours faithfully,



No. 278/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 279/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Engineers Enterprises, THE FIRM Rawabhata Industrial Area

P.O. Birgaon Raipur (C.G.) 493221 Mo.- 9826612012, 9425212012 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Engineers Enterprises, MANUFACTURER Rawabhata Industrial Area




E.D. VAT/CST/ Extra As Applicable

Rate Per Meter








No. 280/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015 4. TERMS OF DELIVERY : F. O. R Destination (Any where in C.G.State) 5. EXCISE DUTY : Not Applicable 6. SALES TAX /VAT : Extra, as Applicable


M/s Engineers Enterprises, Rawabhata Industrial Area P.O. Birgaon Raipur (C.G.) 493221 Mo.- 9826612012, 9425212012 Email- [email protected]

7. DELIVERY PERIOD : 45 Days 8. a. ANNUAL TURN OVER/ : NM b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raipur DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE & COLLARS 60,000 CFT. 9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : Manufacturer

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Raipur DTIC DTIC EM Part-II 220111100656 Dated 18-09-2008


Officers (DDOs).
















19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Engineers Enterprises, INSPECTION Rawabhata Industrial Area











(Suresh Keshi)

General Manager




TSC 15-10-2014







No. 284/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 285/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 286/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/EE/6489 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/GCPI/6490 Dated: 10-04-2015 To,

M/s Grewal Cement Pipe Industries, 31 Industrial Area, P.O. Birgaon 493221 Raipur (C.G.) Mo.- 9826612012 , 9425212012 Email- [email protected]




Yours faithfully,



No. 290/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/GCPI/6490 Dated: 10-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 291/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/GCPI/6490 Dated: 10-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Grewal Cement Pipe Industries, THE FIRM 31 Industrial Area, P.O. Birgaon 493221

Raipur (C.G.) Mo.- 9826612012 , 9425212012 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s Grewal Cement Pipe Industries,

MANUFACTURER 31 Industrial Area, P.O. Birgaon 493221 Raipur (C.G.) Mo.- 9826612012 , 9425212012 Email- [email protected]




Rate Per Meter





(Suresh Keshi)

General Manager






M/s Grewal Cement Pipe Industries, 31 Industrial Area, P.O. Birgaon 493221 Raipur (C.G.) Mo.- 9826612012, 9425212012 Email- [email protected]


b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Raipur DTIC Registration Certificate) Description Capacity/Annum

RCC Hume Pipes, Dust Bins & R.C.C. Half Round Hume Pipe 125000 CFT.

9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final. 11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM 13. REGISTRATION STATUS : Manufacturer is Registered with Raipur DTIC DTIC EM Part-II 220111100654 Dated 16-09-2008 14 BIS LICENSE : Not Mentioned



















ARE TO BE OFFERED FOR M/s Grewal Cement Pipe Industries, INSPECTION 31 Industrial Area, P.O. Birgaon 493221

Raipur (C.G.) Mo.- 9826612012 , 9425212012 Email- [email protected]





TSC 15-10-2014







No. 296/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/GCPI/6490 Dated: 10-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 297/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/GCPI/6490 Dated: 10-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 298/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/GCPI/6490 Dated: 10-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons







Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015 To,

M/s R.C.C. Hume Pipe & Products , S.U.I.E. Frazerpur Nayamundapara , Industrial Estate , Jagdalpur Bastar (C.G.) Ph.- 07782227204 Mo.-9425260321, 9406286611 Email- [email protected]




Yours faithfully,



No. 302/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 303/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s R.C.C. Hume Pipe & Products , THE FIRM S.U.I.E. Frazerpur Nayamundapara ,

Industrial Estate , Jagdalpur Bastar (C.G.) Ph.- 07782227204 Mo.-9425260321, 9406286611 Email- [email protected]

(b) NAME AND FULL ADDRESS OF :- M/s R.C.C. Hume Pipe & Products ,

MANUFACTURER S.U.I.E. Frazerpur Nayamundapara , Industrial Estate , Jagdalpur Bastar (C.G.) Ph.- 07782227204 Mo.-9425260321, 9406286611 Email- [email protected]




Rate Per Meter





10 RCCHPF80001152 Above 200 Km. 37.00



No. 304/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015 6. SALES TAX /VAT : Extra, as Applicable

TIN No. 22162401711

Address:- M/s R.C.C. Hume Pipe & Products , S.U.I.E. Frazerpur Nayamundapara , Industrial Estate , Jagdalpur Bastar (C.G.) Ph.- 07782227204 Mo.-9425260321, 9406286611 Email- [email protected]


2012-13 Rs. 6759008.00 2013-14 Rs. 8810258.00

b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Jagdalpur DTIC Registration Certificate) Description Capacity/Annum

R.C.C. Hume Pipes, Urinal, Latrin, Half Round Pipe, Fencing Pole, Km. Stone, Water Tanker, Flower Pot & Dust Bin.

7200 Nos.


FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Jagdalpur DTIC DTIC EM Part- II 220151100091 Dated 26-05-2008


















19. PLACE WHERE THE STORES : Manufacturer’s Factory at

ARE TO BE OFFERED FOR M/s R.C.C. Hume Pipe & Products , INSPECTION S.U.I.E. Frazerpur Nayamundapara ,

Industrial Estate , Jagdalpur Bastar (C.G.) Ph.- 07782227204 Mo.-9425260321, 9406286611 Email- [email protected]







TSC 15-10-2014







No. 308/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 309/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 310/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/RCCHP&P/6491 Dated: 30-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015 To,

M/s Chhattisgarh Pipe Industries, Village - Bhoinabhata Tah. & Distt. Bemetara (C.G.) Mo.- 9993730777




Yours faithfully,



No. 314/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .
















No. 315/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015



1. (a) NAME AND FULL ADDRESS OF :- M/s Chhattisgarh Pipe Industries, THE FIRM Village - Bhoinabhata

Tah. & Distt. Bemetara (C.G.) Mo.- 9993730777

(b) NAME AND FULL ADDRESS OF :- M/s Chhattisgarh Pipe Industries,

MANUFACTURER Village - Bhoinabhata Tah. & Distt. Bemetara (C.G.) Mo.- 9993730777



E.D. VAT/CST/ TRANSPORTATION

Extra As Applicable Rate Per Meter





10 RCCHPF80001152 Above 200 Km. 37.00



No. 316/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015 6. SALES TAX /VAT : Extra, as Applicable


M/s Chhattisgarh Pipe Industries, Village - Bhoinabhata Tah. & Distt. Bemetara (C.G.) Mo.- 9993730777


b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Durg DTIC Registration Certificate) Description Capacity/Annum


FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Durg DTIC DTIC EM Part- II 220101100637 Dated 01-09-2008




(Suresh Keshi)

General Manager














19. PLACE WHERE THE STORES : Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Chhattisgarh Pipe Industries, INSPECTION Village - Bhoinabhata

Tah. & Distt. Bemetara (C.G.) Mo.- 9993730777






TSC 15-10-2014







No. 320/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 321/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 322/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/CPI/6492 Dated: 30-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons








Registered A/D Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/SI/6493 Dated: 30-04-2015 To,

M/s Star Industries, Mukhtiyarpara Nagpur Manendragarh Korea (C.G.) Mo.- 09424260460, 09993251066




Yours faithfully,



No. 326/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/SI/6493 Dated: 30-04-2015 Copy to, 1. The Secretary, Chhattisgarh Vidhan Sabha ,Raipur .



















1. (a) NAME AND FULL ADDRESS OF :- M/s Star Industries, THE FIRM Mukhtiyarpara Nagpur

Manendragarh Korea (C.G.) Mo.- 09424260460, 09993251066

(b) NAME AND FULL ADDRESS OF :- M/s Star Industries,

MANUFACTURER Mukhtiyarpara Nagpur Manendragarh Korea (C.G.) Mo.- 09424260460, 09993251066




Rate Per Meter



4 RCCHPF80001047 225 275.68 5 RCCHPF80001048 250 309.35 6 RCCHPF80001049 300 309.35 7 RCCHPF80001052 450 1050.00 8 RCCHPF80001053 500 1155.00 9 RCCHPF80001054 600 1480.50 10 RCCHPF80001055 700 1680.00 11 RCCHPF80001056 800 2250.00 12 RCCHPF80001057 900 2936.38 13 RCCHPF80001058 1000 3052.39 14 RCCHPF80001059 1100 3465.00 15 RCCHPF80001060 1200 4378.50 16 RCCHPF80001061 1400 5911.43 17 RCCHPF80001062 1600 7045.31 18 RCCHPF80001063 1800 7793.75


(Suresh Keshi)

General Manager





M/s Star Industries, Mukhtiyarpara Nagpur Manendragarh Korea (C.G.) Mo.- 09424260460, 09993251066


b. MONETARY LIMIT : Not Mentioned c. INSTALLED CAPACITY : (as per Korea DTIC Registration Certificate) Description Capacity/Annum

RCC HUME PIPE 3600 Nos.

9. SLAB DISCOUNT (IF ANY) : Not Mentioned. 10. PRICES : Prices are Firm and Final.

11. MINIMUM QUANTITY IN : Not Mentioned. SINGLE SUPPLY ORDER 12. STATUS OF RC HOLDING : SSI Unit

FIRM

13. REGISTRATION STATUS : Manufacturer is Registered with Korea DTIC DTIC EM Part- II 22/001/12/000143 Dated 23-01-2011




No. 329/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/SI/6493 Dated: 30-04-2015 16. PAYMENT TERMS : The payment of full 100% of prices of the stores of each














19. PLACE WHERE THE STORES Manufacturer’s Factory at ARE TO BE OFFERED FOR M/s Star Industries, INSPECTION Mukhtiyarpara Nagpur

Manendragarh Korea (C.G.) Mo.- 09424260460, 09993251066





TSC 15-10-2014







No. 332/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/SI/6493 Dated: 30-04-2015 Schedule- 3: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for flush joints conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule- 4: Reinforced Concrete, Medium duty, Non-pressure Pipes, Class: NP3, with ends of the pipes suitable for Socket & Spigot, roll on joints or confined gasket joints conforming to IS:458/2003 (Fourth Revision) with up-to-date amendment along with Rubber Ring conforming to Type 2 of IS: 5382/1985 with up-to-date amendment. Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000, 1100, 1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP3 shall be as per the Table 3 of IS: 458/2003(Fourth Revision) with up-to-date amendment 2. Spigot & Socket dimensions of NP3 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-





No. 333/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/SI/6493 Dated: 30-04-2015 Nominal Diameter of Pipes in mm. 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions, Design and Strength requirements of Reinforced Concrete Pipes of Class NP4 shall be as per the Table 6 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 2. Spigot & Socket dimensions of NP4 Class Pipes shall be as per Table 14 & Table 17 of IS: 458/2003(Fourth Revision) with up-to-date amendment. 3. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. Schedule-7: Reinforced Concrete Collar for Reinforced Concrete, Light duty, Non-pressure Pipes, Class: NP2 conforming to IS: 458/2003 (Fourth Revision) with up-to-date amendment. Reinforced Concrete Collar for the Pipes, Class: NP2, size (Nominal Diameter in mm) , is as per below: 80, 100, 150. 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000,1100,1200, 1400, 1600 & 1800. 1. Dimensions and Design requirements of Reinforced Concrete Collar for Pipes of Class NP2 shall be as per the Table 21 of IS: 458/2003(Fourth Revision) with up-to-date amendment. Schedule - 8 Transportation Charges:

Sub Item Code No.





No. 334/336 Rate Contract No. CSIDC/MKD/PS-VII/102/510/15-16/RCCHP/SI/6493 Dated: 30-04-2015 1. Manufacturer shall submit his own Certificate for materials of construction used in the pipes. 2. Manufacturer shall submit Test Certificate for the Steel used for Reinforcement. 3. Manufacture’s Test Repot of Rubber Rings shall be submitted for review (incase of Pipes with Socket & Spigot ends). TESTS: As per prevailing practice, the following Tests / Checking shall be carried out. 1. Visual examination, 2. Permeability Test and 3. Three Edge Bearing Test to produce 0.25 mm crack. 4. Any other Tests that are mentioned in IS: 458/2003 (Fourth Revision) with up-to-date amendment shall be carried out if desired by the Consignee. NOTE: 1. The tolerances on Pipes shall be as per clause 8.2 & tolerances on Collar shall be as per Table No.21 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 2. Workmanship & Finish of the Pipes & Collars shall be as per Clause 9 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 3. The length in which the pipes are to be supplied shall be as per the mutual agreement between the purchaser and the supplier. However, the recommended length above 300 mm Nominal Diameter is 2.5 meters. 4. Curing of the pipes shall be done as per the Clause 7.4 of IS: 458/2003 (Fourth Revision) with up-to-date amendment. 5. Rubber Ring chords used in the Pipe joints shall conform to Type 2 of IS: 5382/1985 with up-to-date amendment. 6. The following information shall be shall be clearly marked on the each Finished Pipe. a. Size of Pipe, b. Class of Pipe, and c. Name of manufacture. 7. The supplier shall guarantee the Pipes and Collars for a period of 12 months from the date of receipt of the materials by the consignee. 8. For Reinforced Concrete Pipes Rates must be quoted on the basis of Per Meter length and in the case of Collars Rates shall be quoted on the basis of Per Piece. (The cost of the Rubber Ring shall be included in the Rate per Meter length of the Pipe. No extra payment towards the supply of Rubber rings will be made) as per the prevailing practice, transportation cost for Pipes & Collars shall be quoted separately.





RCC HUME PIPE











Reasons





chhattisgarh state industrial development corporation limited rcc hume pipe.pdfannexure -“a”...

Documents