bul-71 telecamere ip serie rk - manuale installazione telecamere ip... · rk series - of ip network...
TRANSCRIPT
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:1
DSE SRL - ITALY - WWW.DSE.EU
RK Series IP Cameras IP cameras ONVIF
Installation manual
How to connect the telecameraCome make the local network connection
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:2
DSE SRL - ITALY - WWW.DSE.EU
Contents of this handbook
The range of RK series cameras is a range of IP cameras for network connection optimized for use
with VCRs NVR.In this manual explains how to connect the camera, how to make the basic
adjustments and how to configure the parameters for the connection of network.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:3
DSE SRL - ITALY - WWW.DSE.EU
Introduction The RK series consists of IP network cameras with H264 /
H265 and video resolution 2MP (1080P), up to 4K. It is
"Naked" ie cameras equipped with an essential hardware
equipment destined to those who operates the plant via
an NVR.
The units are connected to a LAN via RJ45 port as a
computer or other network drives and images can be displayed on a
PC using Internet Explorer browser.
The power supply is possible with 12VDC adapter (not supplied) or
via the same network cable using Power over Ethernet (POE)
supported by all cameras in the range.
The cameras RK Series fully supports the international protocol ONVIF and is compatible with
any IP recording software or network video
recorder (NVR) multi-protocol capable of handling
this standard.
DSE is among the few Italian companies to be a
member of the association Onvif and guarantees
the full compliance of its products to the latest
standards.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:4
DSE SRL - ITALY - WWW.DSE.EU
Technical data
See updated at tables:
https://www.dseitalia.it/prod_telecamere_ip_megapixel.htm
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:5
DSE SRL - ITALY - WWW.DSE.EU
Installation CONNECTIONS
All RK series cameras have only 2 connections: a mains socket and a power plug 12VDC,
NETWORK PORT RJ45 - RJ45 FEMALE connector to connect the LAN. To connect to a hub or
network switch using a standard LAN cable. To directly connect a single PC using a crossover
cable (crossover).
POWER POE - The cameras support the 802.3af POE power through the network cable. To
use this form of power is necessary to have switches with POE ports capable of supplying
power. Alternatively you can use the external POE injectors. If you use the POE pin 12VDC
side should not be used.
12VDC - plug which connect the power supply 220VAC / 12VDC (not included) if you do not
want to supply the camera in POE through the network cable. Connect a 12VDC power supply
by at least 1A.
All RK cameras can be used outside and for this feature a network connector waterproof tin and
guarnizionato that must be assembled as shown in Fig. Note that the waterproof connector is
present as an additional protection, but it is always advisable to protect the connections from the
elements inside junction boxes or by purchasing the appropriate watertight boxes for
connections to be installed between the camera and the wall ..
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:6
DSE SRL - ITALY - WWW.DSE.EU
CONNECTION AND VERIFICATION OF NETWORK CONNECTION
Attached to the network CAMERA ONE AT A TIME, because having all the same basic fixed
address should be in conflict. Only after setting the IP address of the first camera you can connect
another one.
After connecting the network cable you should check that the LED on the switch next to the
network port are flashing, to confirm the good current data connection.
ADJUSTMENT MANUAL LENS
The smaller models in this range are equipped with fixed,
non-adjustable lens. In these models, the lens is adjusted
at the factory and should not be focused.
The larger models, with IR over 20 m., Are equipped with
an adjustable lens. In these models, there are 2 external
adjustment screws. We need to act, with the supplied key,
first on the ZOOM screw to adjust the angle of view and then on the FOCUS screw to adjust
finely the development fuoco.Queste adjustments must make observing the image on the
screen. Please take the time to get the perfect setting because this will have a crucial effect on
the effectiveness of the system.
LENS ADJUSTMENT ZOOM MOTORIZED
Models with motorized lens (Ref. ---- Z) allow you to
adjust the zoom by acting directly on the network by
connecting to the Internet Explorer browser or with our
APP, or via the NVR. It acts on the PTZ CONTROL to set the
desired zoom. The focus is automatic.
ASSEMBLY OF CAMERAS MILLS
The cylindrical cameras are equipped with an integrated
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:7
DSE SRL - ITALY - WWW.DSE.EU
bracket for wall mounting, specially designed to allow the passage of cables inside it and protect
them from tampering. The camera is mounted generally in the output cables so as not to leave
exposed wires. The fixing base has, however, also with a slot lateral cable outlet if the cables
come in laterally outer raceway.
The bracket is fastened to the wall or ceiling with the supplied dowels. On the back of routes
bracket is a bearing made of insulating foam whose function and eliminate the space for the
penetration of insects.
With the Allen key supplied is necessary to loosen the retaining screw B and then point the
camera thanks to the joint A. At the end tighten the retaining screw B for locking the camera in
its position
ASSEMBLY OF CAMERAS SPHERICAL
The spherical cameras are composed by the camera globe and
from the fixing base which are screwed to each other. Prior to
mounting, unscrew the fixing base by separating it from the
camera body. No need for tools typically used to loosen the fixing
base from the camera body, however, if this proves too tight at
the bottom it is possible to helpplacing a rigid rod, for example a
screwdriver, between the two outlet eyelets lateral cables placed
in the base.
The fixing base, separated from the camera, is fixed to the wall or
wall with bolts in correspondence with the outlet hole and cables on it subsequently screwing the
camera body. Before tighten properly orient the viewing angle.
CONNECTIONS BOXES
Both for the cylindrical and spherical models are available separately watertight boxes to
accommodate the connections, to be mounted between the wall and the bracket. The cassettes
have input cables rear, or side (fairlead included tin) and bear on the cover the fastening holes for
the different models.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:8
DSE SRL - ITALY - WWW.DSE.EU
AVOID OBJECTS CLOSE TO THE CAMERA
In the position the camera is necessary to prevent objects from entering neighbors in the
shooting field, such as edges, leaves etc. because at night they would strongly illuminated by the
illuminator IR causing strong darkening the image. For the same reason we must not to fit into
the wall near the camera.
Aim the camera so that it has a nice open view in front of him.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:9
DSE SRL - ITALY - WWW.DSE.EU
Network Configuration After providing power to the camera via a 12VDC power supply or via POE and after connecting
to the network configuration of the network parameters you must proceed in such a way to be
able to make the cameras accessible by computer. The cameras are supplied with a fixed
address of 192.168.1.168 Factory
SOFTWARE IPCSEARCH The CD supplied with the camera includes the IPCSearch software that can be installed on
any PC on the network. The function of this software is to detect the presence of the camera
in the network, regardless of its address, and allow you to change the camera address in
order to be consistent with your network. We recall that because the camera is visible from
the other PCs on the network it is necessary that the first 3 address parts are the same as
other network PC and is equal also the subnet mask. And 'advisable to connect a network
camera at a time, and insert new ones after you have set earlier.
PRELIMINARY CHECKS Before you must obtain from your network some information about the management of the
IP addresses used on your network. E 'need to know an IP address can be assigned to the
camera that is not equal to any other device already present in the network. If you are
uncertain about the operation of your network, you can use certain commands in DOS
PROMPT.
On a network PC launched a DOS window available between the Windows accessory
programs.
Type IPCONFIG at the command prompt and press ENTER. They will see the TCP / IP
parameters. The second line is the IP address assigned to your computer.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:10
DSE SRL - ITALY - WWW.DSE.EU
In the above example the address of the PC on which you are working is 192.168.2.3 and the
subnet mask used is the classic 255.255.255.0. The camera can therefore assign an address
chosen by the 192.168.2.XXX type, where XXX stands for a number between 0 and 255.
It 'important to choose an address that is not already used by other network equipment. To
verify that the chosen address is free, try to make a PING from the same DOS window by
typing PING followed by a space and by the IP you wish to assign to the camera. If there is
no device responds to that address, you will receive 4 REQUEST TIME OUT as in the following
example:
All cameras support the automatic IP address assignment from a DHCP server. This mode,
however, is not recommended because in the event of power failure or restart of the
equipment it is possible that the cameras IP address change necessitating a reconfiguration
of the NVR.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:11
DSE SRL - ITALY - WWW.DSE.EU
IPCSEARCH OF USE TO ASSIGN IP ADDRESS All RK Series cameras are preset with the IP address by default: 192.168.1.168
After connecting the camera you need to change the address of the camera to assign one
consistent with its own network (first 3 parts of the address common to all network equipment).
Proceed as follows: 1. Insert the CD into a PC player and explore the content. You will find a folder called
IPCSEARCH within a program. Install the program on a network computer and run it. If you
have lost the CD, you can download it from our website.
2. The program searches for all devices DSE RK series on the network. Wait to complete the
search. IPCSEARCH is able to detect even cameras with different address class from that of
the PC on which you are working.
3. When the search will see the list of detected cameras. If the camera is not detected check
the functionality of network links. In the IP ADDRESS column shows the IP address of the
camera current. Click on the camera and you will see appear in the right section all other
network parameters.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:12
DSE SRL - ITALY - WWW.DSE.EU
4. Of particular relevance are of the IP address (IP ADDRESS) which must have the same class
of the network (first three groups of equal numbers) and SUBNETMASK to be the same one
used by the network (typically 255.255.255.0). The gateway is the router address, usually
the number one network. DNS is important because the camera recognizes websites by
name and can, for example, send e-mail. If you do not know the DNS of your Internet
service provider you can enter the Google DNS: 8.8.8.8. You can edit the network
parameters at will by writing in the boxes. Do not forget to enter the camera's login
credentials (admin / admin Factory)
5. Press MODIFY to transfer the new configuration in the camera. Wait at least one minute and
in any case until, by pressing the SEARCH button, the camera is not detected with the new
address.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:13
DSE SRL - ITALY - WWW.DSE.EU
with browser access
Once properly set the network parameters, you can make the first access to the camera using the
IE browser. Although now little used in the normal web browsing, Internet Explorer browser is the
reference in the video surveillance management activeX plugin.
Accertateci to use Internet Explorer and not other browsers such as Microsoft Edge, Chrome,
Firefox, they will not function.
ENABLE PERFORMANCE OF ACTIVEX Internet Explorer has security settings that may prevent the installation of the ActiveX
component. Before making the connections necessary to enable the execution of ActiveX not
marked as safe. In Internet Explorer, select TOOLS / INTERNET OPTIONS
In the folder PROTECTION choose the area of interest (Internet or local network) and click
CUSTOM LEVEL. Enable all items for the download and execution of ActiveX especially those NOT
marked as safe. E 'can set the items either ENABLE or ASK FOR CONFIRMATION. Finally, save and
restart the browser.
ACCESS WITH INTERNET EXPLORER To access the camera using Internet Explorer, type in the address box, the IP address that
you assigned. In the example below we perform a link on the internal network to the camera
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:14
DSE SRL - ITALY - WWW.DSE.EU
with IP address 192.168.2.30.
It is not necessary to specify the connection port since the cameras using factory port 80
which is the one usually used by browsers.
If for any reason you change the port to call by allowing it to IP address HTTP port then it will
be necessary to specify in the browser on the camera settings. In this example we are calling
the 192.168.2.30 IP on port 85.
INSTALLING ACTIVEX In order to make sure that the IP RK Series cameras are displayed on the browser you must
install the ActiveX components. At the first access that carried out, the camera will detect
the absence of these components and display the following window.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:15
DSE SRL - ITALY - WWW.DSE.EU
Click on DOWNLOAD to download the activeX components.
E 'can both run the program directly by choosing RUN to save the file on your local PC and
then install it manually. Once the program is installed you see this message
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:16
DSE SRL - ITALY - WWW.DSE.EU
That confirms the successful installation. Now restart your browser and then restore the
connection.
LOG-IN If the connection to the camera has good end it presents the log-in window
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:17
DSE SRL - ITALY - WWW.DSE.EU
The RK Series of cameras factory login details are:
USERNAME: admin
PASSWORD: admin
The access to the camera control mask.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:18
DSE SRL - ITALY - WWW.DSE.EU
The commands shown in the window are described in detail in the configuration manual.
MAXIMUM NUMBER OF CONNECTED CLIENTS Each camera accepts up to 15 simultaneous connections to many remote clients.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:19
DSE SRL - ITALY - WWW.DSE.EU
Connecting player RTSP
The cameras support RTSP protocol factory is set to use port 554. It 'can connect to the camera
using any RTSP player such as VLC.
The address to call must have the following syntax:
RTSP: // IP: PORT / 0
Here's an example:
rtsp: //192.168.2.33: 554/0
Below such as operate eg with the VLC player:
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:20
DSE SRL - ITALY - WWW.DSE.EU
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:21
DSE SRL - ITALY - WWW.DSE.EU
WIFI cameras Installation
The camera RK Series with wifi are installed as the rows cameras, but with the further need of
connection to the local wifi network. Initially you need to connect the camera with the network
cable and assign an IP address row. Then you can enter the NETWORK - ADVANCED
CONFIGURATION configuration - WIFI and connecting the camera to its WiFi network.
E 'can connect to the WiFi network in DHCP with automatic address assignment, or set a static IP
address.
When the camera shows Successful connection to the wifi network you will have two IP addresses: one on the wired network and one on the wifi network. You can at this point disconnect the network cable and keep the only connection with the WiFi address.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:22
DSE SRL - ITALY - WWW.DSE.EU
Login with ONVIF NVR The RK Series IP cameras are cameras provided "NAKED",
that is optimized to work in plants managed by NVR.
These rule cameras are connected to network video
recorders or external recording software.
To do this you use the ONVIF standard that these cameras
support pienamente.Per connect cameras to NVR or software ONVIF refer to the recording
equipment manuals. As a rule the NVR automatically recognize the communication parameters to
communicate with the telecamere.In case it is necessary the manual insertion is known that the
RK series cameras use port 80 to communicate with the NVR on onvif protocol.
CAUTION
In RK load a camera on an NVR is important NOT KEEP NEVER credentials (username and
password) proposals from NVR, even though seem correct, but always manually override both.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:23
DSE SRL - ITALY - WWW.DSE.EU
Direct access to the web via router The Internet connection to the "Naked cameras" as RK this range, as a rule is not made by calling
individual cameras but by connecting all'NVR.Per this type of connection is necessary to refer to
the manual of NVR.
E ', however, can also connect to the web directly to the cameras with the Internet Explorer
browser. To do this you need to make a configuration inside the router following the directions in
this chapter where we explain the mapping of ports that comunicazione.Ricordiamoyou can
avoid this configuration by using the connection with our cloud servers P2P remote
access is explained in the manual.
MAPPING WITH WEB ACCESS DOORS ROUTER
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:24
DSE SRL - ITALY - WWW.DSE.EU
An installation of IP cameras is often placed inside a LAN connected to the Internet via a router
as in the following scheme
If we use for viewing the cameras internal PC to the network, the addresses of the cameras
(usually the 192.168.XXX.XXX type) are directly accessible. If you wish to connect via the
Internet using a PC placed elsewhere, the internal network addresses will no longer be reached
directly, because the only IP address visible from the web will be what our router will by its WAN
side that is towards the outside world Internet.This address is assigned by the provider (ISP).
And 'advisable to get from the provider a fixed address each time you connect. If there is a
chance you need to use DDNS services (see assembly manual) .There is, however, simply type in
the browser the IP address of the router wan side in order to connect the cameras. The router
acts as a filter and drops every external call that a call from within the network is not paid before.
In order to connect the cameras it is therefore necessary to insert inside the router ports of
directing instructions which, depending on the router manufacturers are called NAT, PORT
FORWARDING, PORT MAPPING etc.
In practice, access the router configuration and insert instructions so that it directs the external
incoming calls, to the internal IP address of the telecamere.Ovviamente directing is only
performed for the communication ports that are used by the cameras and that will be detailed
below.
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:25
DSE SRL - ITALY - WWW.DSE.EU
The communication ports used by the RK Series cameras are as follows:
HTTP PORT: Default 80. The cameras use this port to communicate with browsers like IE.
Browsers such as Internet Explorer use the factory port 80 for communication. For example,
if we type in the browser address bar: http://212.12.34.201 will be called the IP address
212.12.34.201 port 80.
If in the configuration of the camera is set to a different HTTP port (eg. 81, 82, etc.) needs to
be clarified in the browser which port to use for the call after pointing the address with ":" as
the separation. If, for example. http://212.12.34.201:81 we type will be called the IP
address 212.12.34.201 port 81.
PORT RTSP: By default 554. E 'used by the camera to send the RTSP video clients such as
VLC, Real Player etc ..
If behind the router counts more than one camera and you want to reach them individually from
the outside you must be assigned to each of them a different http port. For example 80,81,82
doors etc.
In the NAT router settings you will have the direction of each door towards the inside address of
the own camera.
Note that many routers require that each directing NAT is also combined with a rule in the firewall
section that determines the opening of the affected port. Consult your router's manual for details
on how to program the port mapping
INSTALLATION MANUAL
RK SERIES - OF IP NETWORK CAMERAS Page:26
DSE SRL - ITALY - WWW.DSE.EU
WEB access with CLOUD P2P
To make it easier to connect via the Internet, even without a static IP and no port configuration
of the router, the cameras are equipped with the support of a cloud server P2P. The remote
connection through our cloud servers, PCs and mobile, is explained in the manual for remote
access.