bmw parts and accessories installation instructions

1 4

2 5

6

MODE

FM AM

3

MENU

INFO

TONE SELECT

F 38 0393 B

Retrofit Kit On-board Monitor and Navigation System

BMW 7 Series (E38)

The installation instructions are only valid for vehicles which are equipped with OE555 Highon-board computer.

Technical and electrical knowledge is requiredInstallation time approx. 7 hours, which can vary according to the condition and fittings of thevehicle.Retrofit/Installation Kit no. 65 90 0 025 170

BMW Parts and AccessoriesInstallation Instructions

Retrofit/Installation Kit no.: 65 90 0 025 170 Date: 09.2000Installation Instructions no.: 01 29 0 027 075

Contents

Chapter Page

1. Important notes on the installation of the on-board monitor and navigation system ....48

2. Preparatory work..........................................................................................................49

3. Parts overview..............................................................................................................50

4. Connection overview....................................................................................................53

5. Installation and cabling diagram of the on-board monitor wiring harness ....................57

6. Installation and cabling diagram of the supplementary wiring harness for navigation ..58

7. Install on-board monitor wiring harness, on-board monitor and on-board monitor

radio ............................................................................................................................59

8. Install supplementary wiring harness for navigation in vehicles prior to production

date 9/98 ....................................................................................................................61

9. Choose installation of the supplementary wiring harness for navigation in vehicles

from production date 9/98 ..........................................................................................66

10. Install supplementary wiring harness for navigation in vehicles from production

date 9/98 (PIN18 and PIN35 at connector of the hydraulic unit ABS not assigned) ....67


date 9/98 (PIN18 and PIN35 at connector of the hydraulic unit ABS assigned) ..........70


date 9/98 (PIN18 assigned and PIN35 not assigned at connector of the hydraulic

unit ABS)......................................................................................................................72


date 9/98 (PIN18 not assigned and PIN35 assigned at connector of the hydraulic

unit ABS)......................................................................................................................75

14. Install navigation system ..............................................................................................78

15. Coding and finalising operations..................................................................................83

16. Connection description forTV function ......................................................................85

17. Circuit diagram, on-board monitor wiring harness........................................................86

18. Circuit diagram, navigation system wiring harness ......................................................88

19. Circuit diagram, supplementary wiring harness for navigation system..........................90

20. Template for the installation of the navigation computer ..............................................92


1. Important notes on the installation of the on-board monitor and navigation system

Only for use within the BMW trading organisation.

Installation of the on-board monitor and the navigation system may only be undertaken by aspecialist workshop which has available the necessary special tools and the required manuals(maintenance, repair, diagnostic, etc.).

When cables/leads are being installed, care should be taken to see that they do not getkinked or damaged.Additionally installed cables/leads should if necessary be fastened with cable straps.

Item numbers relate only to the overviews or to the text at the side of the associatedillustration.

All operations are represented as taking place on a left-hand drive vehicle, the samelogical procedure must be followed for right-hand drive vehicles.

Electrical knowledge is required.

The function carrier for the on-board monitor and the on-board monitor radio areequipment-dependent and must be ordered separately in accordance with the ElectronicsParts Catalogue (EPC).The bracket for the video module does not form part of the installation kit and, for installationof a video module (TV function), must be ordered separately in accordance with the ElectronicParts Catalogue (EPC).The control cable of the on-board monitor radio/CD changer does not form part of theinstallation kit and, for vehicles with CD changer without DSP amplifier, must be orderedseparately in accordance with the Electronic Parts Catalogue (EPC).The boot trim-panels at rear left do not form part of the installation kit and must be orderedseparately in accordance with the Electronic Parts Catalogue (EPC) only for vehicles withoutTOP HiFi system and without CD changer (in vehicles with Top HiFi system or CD changer, theexisting boot trim-panels at rear left can be cut).

Rights are reserved to make technical modifications.

Required tools and auxiliary materials

MoDIC III or DIS Hot air dryerSet of 1/4 inch socket wrenches Set of Torx socket wrenchesSet of Phillips screwdrivers Set of flat-tip screwdriversCable lamp MultimeterSide-cutting pliers Short Phillips screwdriverSilicone

EN/48Retrofit/Installation Kit no.: 65 90 0 025 170 Date: 09.2000Installation Instructions no.: 01 29 0 027 075

2. Preparatory work

TIS AW NO.Print out error memory

Disconnect battery 12 00 ...

Dismantle finisher of instrument panel, centre left 51 45 030

Dismantle finisher of instrument panel, right 51 45 030

Dismantle radio (no longer required) 65 11 030

Dismantle operating unit forTop HiFi system or coin compartment

(no longer required) 65 12 040

Dismantle multi-information display (no longer required) 65 81 010

Dismantle air conditioning operating unit 64 11 750

Dismantle individual control switches or switch panels in the

function carrier 64 11 750

Dismantle function carrier of radio, is to be replaced by function

carrier of on-board monitor 51 16 202

Re-mount can holder, front 51 16 202

Dismantle facing centre console, front left 51 16 239

Undo centre console, below front left 51 16 239

Dismantle left front seat 52 17 000

Dismantle rear seat bench 52 24 005

Dismantle rear seat back 52 24 015

Dismantle sill strip, left front and left rear 51 47 000/51 47 030

Dismantle lower part of the B-pillar trim panel, left

Fold up carpet on left

Dismantle C-pillar trim panel on left and right 51 43 251

Dismantle rear window shelf 51 46 000

Dismantle boot floor 51 47 101

Dismantle entire side trim panel in boot on left 51 47 151

Dismantle rear side trim panel in boot on right 51 47 172

Dismantle trim panel of closing panel 51 46 050

Dismantle sill strip at right front and right rear 51 47 000/51 47 030

Dismantle lower part of the B-pillar trim panel, right

Dismantle A-pillar trim panel, lower right

Dismantle glove box 51 16 360

Dismantle footwell trim panel in front of glove box

Fold up carpet on right

Dismantle CD changer (if exists) 65 11 070

Dismantle bracket for CD changer (if exists)

Dismantle telephone components with supports (if they exist)

Dismantle DSP amplifier (if exists) 65 11 070

Dismantle bracket for DSP amplifier (if exists) 65 11 070


EN/49

In addition for right-hand drive vehicles

TIS AW No.Dismantle footwell trim panel under the steering column


3. Parts overview

EN/50

1 4

2 5

6

MODE

FM AM

3

MENU

INFO

TONE SELECT

1511 14

10

13

87

1 2

3 4 5

9

6

12

F 38 0395 B


3. Parts overview

EN/51

18

25

19

17

24

16

20

2928

2726

2221 23

30 31 32

F 38 0394 B

3. Parts overview


1 On-board monitor wiring harness2 Navigation wiring harness3 Supplementary wiring harness for navigation system4 Antenna extension for GPS antenna5 GPS antenna6 Mounting clip7 Bracket of GPS antenna8 Complete on-board monitor9 On-board monitor holding pin ( for supporting the on-board monitor)10 Function carrier of on-board monitor11 Retaining clip of on-board monitor12 Cross-recess fillister head screw M3x8 (4 items)13 Cover for on-board monitor14 On-board monitor radio*15 On-board monitor radio bracket16 Basic carrier17 Bracket of video module18 Navigation computer19 Bracket of navigation computer20 Hex nut with washer M521 Hexagon bolt with washer M5x14 (12 items)22 Plug-in nut M5 (9 items)23 Bush (for attachment of the bracket of the GPS antenna) (2 items)24 Expanding rivet (for attaching the GPS antenna) (2 items)25 Disassembly clip (2 items)26 Cable strap (20 items)27 AW cable strap (2 items)28 Cover frame29 Cable duct30 Shrinkage tubing (contained in the supplied package of the supplementary wiring harness

for navigation system) (4 items)31 Protective strip (2 items)32 Template (for installation of the navigation computer)

The parts marked with a * are not included in the parts kit and must be ordered separately ineach case in accordance with the vehicle equipment and with reference to the ElectronicParts Catalogue (EPC).

4. Connection overview


A4

A14

A17

A13

A5

A15

A18

A10

A9A11

A16

A12

A6

A7A8A1

A2

A3

B

B4B5

B2

B1

B6B3

A

D

D1C1

C

C7

C8

D2

C4 C5

C2

C3 C6

F 38 0396 B


EN/54

A

A1

A2

A3

A4

A5

A6

A7

A8

A9

A10

A11

A12

A13

A14

A15

A16

A17

A18

On-board monitor wiringharness

blue 12-pole socket housing

white 12-pole socket housing

black 17-pole pin housing

coaxial pin housing

coaxial pin housing

coaxial socket housing

coaxial pin housing

ring terminal Ø6 mm


white 18-pole socket housing


angled coaxial socket housing


natural coloured 6-pole pin

housing

10-pole socket housing


black coaxial socket housing

(antenna connection)

black 17-pole socket housing

-

at blue 12-pole pin housing at on-board monitor (8)

at white 12-pole pin housing at on-board monitor (8)

at black 17-pole radio connector X18126

is installed to installation location of the right TV amplifier

in the C-pillar on the right and tied back

at coaxial socket housing at antenna diversity

at coaxial pin housing at antenna diversity

is installed to installation location of the left TV amplifier

in the C-pillar on the left and tied back

at ground post X13016 at the C-pillar left

at branch cable B4, black 10-pole socket housing, of the

navigation wiring harness B

is tied back with cable strap at on-board monitor wiring

harness A

at blue 18-pole pin housing at navigation computer (18)


harness A


harness A

at branch cable B1, natural coloured 6-pole socket

housing, of the navigation wiring harness B

is clipped into black 17-pole socket housing A18 of the

on-board monitor wiring harness A and plugged in with

the black 17-pole socket housing A18 of the on-board

monitor radio (14)

at coaxial pin housing at on-board monitor radio (14)

at coaxial pin housing at on-board monitor radio (14)

(antenna connection)

at on-board monitor radio (14)

Item Designation Cable colour Connection point in vehicle

-

-

-

-

black

black

black

black

brown

-

-

-

black

black

-

-

black

black

-


-

at branch cable A14, natural coloured 6-pole pin housing

of the on-board monitor wiring harness A

at branch cable C1, black 6-pole pin housing of the

supplementary wiring harness for navigation C

In vehicles equipped with Basis-Interface Telephone 2

(BIT2), plug together branch cable B3, black 6-pole pin

housing, of the navigation wiring harness B, with the

black 6-pole socket housing of the Basis-Interface

Telephone wiring harness (BIT2).

In vehicles without Basis-Interface Telephone 2 (BIT2),

insulate and tie back braanch cable B3, black 6-pole pin

housing, of the navigation wiring harness B.

at branch cable A9, black 10-pole pin housing, of the on-

board monitor wiring harness A

is tied back with cable strap to the navigation wiring

harness B

at Bordeaux-coloured 18-pole pin housing at navigation

computer (18)

-

at branch cable B2, black 6-pole socket housing, of the

navigation wiring harness B

at light module X10117 in black 54-pole socket housing,

PIN38

In vehicles prior to production date 9/98insulate with shrinkage tubing and tie back

In vehicles from production date 9/98at joint connector X10183 (cable colour at joint connector

yellow/red), in case C3 is not required, insulate with

shrinkage tubing and tie back, in LHD vehicles tie back

excess length


In vehicles from production date 9/98at joint connector X10184 (cable colour at joint connector

yellow/white), should C3 not be required, insulate with

shrinkage tubing and tie back, in LHD vehicles tie back

excess length


EN/55


Navigation wiring harness

natural coloured 6-pole socket

housing





Bordeaux-coloured 18-pole socket

housing

Supplementary wiring harnessfor navigation


1-pole blade terminal contact



B

B1

B2

B3

B4

B5

B6

C

C1

C2

C3

C4


-

-

-

-

-

-

-

-

-

white/yellow

yellow/red

yellow/white


EN/56






Antenna extension forGPS antenna

Coaxial pin housing

Coaxial socket housing

C5

C6

C7

C8

D

D1

D2

In vehicles prior to production date 9/98at connector X1171 of the ABS control unit in PIN9, in

LHD vehicles tie back excess length

In automatic vehicles with M62 B44 engine and DSC,from production date 9/97 to production date 9/98at connector X1171 of the ABS control unit in PIN72, in


In vehicles from production date 9/98insulate with shrinkage tubing and tie back

In vehicles prior to production date 9/98at connector X1171 of the ABS control unit in PIN42, in


In automatic vehicles with M62 B44 engine and DSC,from production date 9/97 to production date 9/98at connector X1171 of the ABS control unit in PIN73, in


In vehicles from production date 9/98insulate with shrinkage tubing and tie back


In vehicles from production date 9/98at black 42-pole connector X1170 of the hydraulic unit

ABS in PIN35, should C7 not be required, insulate with

shrinkage tubing and tie back


In vehicles from production date 9/98at black 42-pole connector X1170 of the hydraulic unit

ABS in PIN18, should C8 not be required, insulate with

shrinkage tubing and tie back

-

at GPS antenna (5)

at navigation computer (18)


yellow/red

yellow/white

yellow/red

yellow/white

-

-

-

A3

A2

A1

A5

A6 A7

A8

A9 A10A11

A12

A13

A14

A18

A15A16

A17

A4

X13016

A

F 38 0398 B

5. Installation and cabling diagram of the on-board monitor wiring harness

The on-board monitor wiring harness A is, as shown, to be installed along the audio or mainwiring harness and to be fastened with cable straps.

When installing the on-board monitor wiring harness A, you should begin at the groundpost X13016 in the area of the C-pillar at rear left.

Branch cable A8, screw on at ground post X13016 in the area of the C-pillar, rear leftOn-board monitor wiring harness A traverses behind the left front seat and from there isinstalled along the gearbox tunnel behind the centre console to the installation location of theon-board monitor.Branch cable A4 to the installation location of the right-hand side TV amplifier at the C-pillar,right (is only connected in association with the installation kit of a video module and the TVamplifiers)Branch cable A5 and A6 to the antenna amplifier at the C-pillar, left.Branch cable A7 to the installation location of the left TV amplifier at the C-pillar left (is onlyconnected in association with the installation kit of a video module and the TV amplifiers)Branch cable A1, A2 and A3 along the series audio wiring harness to the installation locationof the on-board monitor in the I-panelBranch cables A9 to A18 through the opening in the rear window shelf along the main cableloom in the bootInstall branch cable A9 to the installation location of the video module bracket in the sidepart, rear left and clip into branch cable A14Branch cables A10 to A13 to the installation location of the navigation computer in the sidepart, rear leftTie back branch cables A10, A12 and A13 (they are only connected in association with theinstallation of a video module and the TV amplifiers)Install branch cable A14 to the installation location of the video module bracket in the sidepart, rear left and snap in with clipped-in branch cable A9 at mounting clipBranch cables A15 to A18 to the installation location of the on-board monitor radio in the sidepart, rear left.

Any excessive lengths should be tied back


F 38 0399 B

C2 C

C1

C3C4RHD C3RHD C4

C7 C8C5C6

RHD C5RHD C6

6. Installation and cabling diagram of the supplementary wiring harness fornavigation

The supplementary wiring harness for navigation C should be installed as shown andfastened with cable straps.

When installing the supplementary wiring harness for Navigation C, you should beginwith branch cable C1.

Key:Installation in all vehiclesAdditional installation for vehicles from production date 9/98Additional installation for vehicles prior to production date 9/98

Branch cable C1 to taillight cup in boot, rear leftBranch cable C2 to C8 along the closing panel to the right side part, from there through thelead-through grommet in the rear window shelf into the vehicle interior and from there alongthe right main cable loom to the installation location of the light moduleBranch cable C3 and C4 to the joint connector behind the glove boxBranch cable C5 and C6 to the installation location of the ABS control unit behind the gloveboxBranch cable C7 and C8 through the lead-through grommet in the bulkhead into the enginecompartment to the installation location of the hydraulic unit ABS

Tie back any excess lengths



Screw branch cable A8, ring terminal Ø 6 mm, ofthe on-board monitor wiring harness A, to theground post X13016 at the C-pillar, rear left.Tie back branch cable A7, coaxial pin housing, ofthe on-board monitor wiring harness A, withcable strap (26) (is only connected in associationwith the installation of a video module).Screw off existing coaxial pin housing (40) of theantenna amplifier (41) and tie it back (is nolonger required).Screw branch cable A5, coaxial pin housing, ofthe on-board monitor wiring harness A, onto thefreed coaxial socket housing (42) of the antennaamplifier (41).Unpin existing coaxial socket housing (43) of theantenna amplifier (41) and tie it back (is nolonger required).Plug branch cable A6, coaxial socket housing, ofthe on-board monitor wiring harness A, on to thefreed coaxial pin housing (44) of the antennaamplifier (41).Install branch cable A4, coaxial pin housing, ofthe on-board monitor wiring harness A, on therear window shelf along the rear window to theinstallation location of the right TV amplifier to theC-pillar on the right and tie it back with cablestraps (26) (is only connected in association withthe installation of a video module).

7. Install on-board monitor wiring harness, on-board monitor and on-board monitor radio

A4

A AX13016

A8

A6

A54344

42

4041

A726

F 38 0400 B

EN/59


Before the work steps are carried out asshown in the illustration, the new function carrierof the on-board monitor (10) must be fitted andequipped as described in the TIS.

Plug together branch cable A3, black 17-pole pinhousing, of the on-board monitor wiring harness A, with the existing black 17-pole sockethousing X18126. Stick one rattle protector (31)onto the second rattle protector (31) and thenstick it onto the wiring harness in such a waythat the existing angled coaxial socket housing(40), the black coaxial socket housing (41)(antenna connection), the connector of the multiinformation display, and the operating unit for theTop HiFi system (if present), and the plug-inconnector A3+X18126 are enclosed.The enclosed connections, as well as theenclosed plug-in connector A3+X18126 are nolonger required and should be placed behind theheating and ventilation operating unit.Screw on-board monitor holding pin (9) on to theon-board monitor (8).Plug branch cable A1, blue 12-pole sockethousing, of the on-board monitor wiring harness A, onto the blue 12-pole pin housing(42) of the on-board monitor (8).Plug branch cable A2, white 12-pole sockethousing, of the on-board monitor wiring harness A, onto the white 12-pole pin housing(43) of the on-board monitor (8).Then feed the cables into the on-board monitorcavity (44) and carefully push in the on-boardmonitor (8).When pushing the on-board monitor in, makesure that no cables become damaged.


44

4041

A2A1

10

43

42A

A3

X18126

8

9

31

F 38 0401 B

1 4

2 5

6

MODE

FM AM

3

MENU

INFO

TONE SELECT812

10

13

F 38 0402 B

Screw on-board monitor (8) to the functioncarrier of the on-board monitor (8) with fourcrossed recessed raised cheese head screwsM3x8 (12).Then put the cover for the on-board monitor (13)onto the on-board monitor (8).

EN/60

Illustration shows boot, rear left.

Couple the on-board monitor radio bracket (15)into the on-board monitor radio (14) below andscrew it on above with a hex nut with washer M5(20) or with a hexagon bolt with washer M5x14(24), depending on the design of the on-boardmonitor radio (14).Remove blue locking clamp (40) from the black17-pole socket housing A18 and plug in branchcable A15, 10-pole socket housing, of the on-board monitor wiring harness A, at thedesignated place in the black 17-pole sockethousing A18.

In vehicle with CD changer without DSPamplifier, the control cable of the on-boardmonitor radio/CD changer will have to befitted additionally.

Secure branch cable 15, 10-pole socket housing,with the blue locking clamp (40).Then detach the insulating mat (41) in the sidepart, inside rear left.


1420/21

15

41

A1840

A15

F 38 0403 B


DE/61

Screw the on-board monitor radio bracket (15)with attached on-board monitor radio (14) on tothe cross-brace (40) in the side part, rear left,with two hexagon bolts with washers M5x14 (2).Plug branch cable A17, black coaxial sockethousing, (antenna connection), of the on-boardmonitor wiring harness A, onto the coaxial pinhousing (41) at the on-board monitor radio (14).Plug branch cable A16, angled coaxial sockethousing, of the on-board monitor wiring harness A, on to the coaxial pin housing (42) atthe on-board monitor radio (14).Plug branch cable A18, black 17-pole sockethousing, of the on-board monitor wiring harness A, onto the black 17-pole pin housing(43) at the on-board monitor radio (14).The cables of the plugged-in branch cables A16,A17 and A18 should be fastened with cablestraps (26).Put two plug-in nuts M5 (22) on to the pre-punched holes in the cross-brace (40) in the sidepart, rear left and mount the detached insulatingmat again in the side part, rear left.Clip in branch cable A9, black 10-pole pinhousing, of the on-board monitor wiring harness A, into branch cable A14, natural-coloured 6-pole pin housing, of the on-boardmonitor wiring harness A.Then clip in the mounting clip (6) into branchcable A14, natural-coloured 6-pole pin housing(is later snapped into the bracket of the videomodule).


15

4014 41

A17A16

42

A1843

A1421

22

A9

626

F 38 0404 B

2116

40

22 F 38 0405 B

Put a plug-in nut M5 (22) on to the designatedplate in the side part, rear left.Screw the basic carrier (16) onto the three plug-in nuts M5 with three hexagon bolts withwashers M5x15 (21), as shown in the illustration.

Take care to see that the insulating mat (40)is mounted first.


Clip in branch cable C1, black 6-pole pinhousing, of the supplementary wiring harness fornavigation C, to the existing plug-in connector(40) at the taillight cup (41), rear left.Install supplementary wiring harness fornavigation C along the closing panel to the rightside part.Fasten supplementary wiring harness fornavigation C with cable straps (26).

8. Install supplementary wiring harness for navigation in vehicles prior to production date 9/98

41

C

40 C1

26

F 38 0406 B

41

40

C

26

C2-C8

F 38 0407 B

40

X10117

C2

F 38 0408 B

Dismantle insulating mat (40) in the right sidepart, rear.Install supplementary wiring harness fornavigation C, as shown, to the lead-throughgrommet (41) in the rear window shelf.Then install branch cables C2 to C8 through thelead-through grommet (41) into the vehicleinterior and from there along the right main cableloom to the installation location of the lightmodule in the A-pillar on the right.Fasten supplementary wiring harness fornavigation C with cable straps (26) and installinsulating mat (40) again in the right side part,rear.

Dismantle light module (40), unpin the black 54-pole socket housing X10117 from the lightmodule (40) and open it.Plug in branch cable C2, 1-pole blade terminalcontact, cable colour white/yellow, into PIN38 ofthe black 54-pole socket housing X10117.Close black socket housing X10117, plug it inand reinstall light module (40).If necessary tie back excessive length of thesupplementary wiring harness for navigation Cbefore branch cable C2.



Illustration shows installation in a left-handdrive vehicle.You should proceed in the identicallogical sequence for right-hand drive vehicles.

Push on shrinkage tubing (30) for insulation ineach case onto branch cable C3, 1-pole bladeterminal contact, cable colour yellow/red, branchcable C4, 1-pole blade terminal contact, cablecolour yellow/white, branch cable C7, 1-poleblade terminal contact, cable colour yellow/redand branch cable C8, 1-pole blade terminalcontact, cable colour yellow/white, of thesupplementary wiring harness for navigation C,and shrink them on with a hot-air dryer.Then tie back with cable straps (26) branchcables C3, C4, C7 and C8 in the area of the rightfront sill.In left-hand drive vehicles, install branch cablesC5 and C6 of the supplementary wiring harnessfor navigation C to the ABS control unit (40) onthe left by the side of the glove box (excesslength must be tied back).In right-hand drive vehicles, install branch cablesC5 and C6 from the supplementary wiringharness for navigation C behind the heater boxtowards the left to the ABS control unit on theright by the side of the glove box.Dismantle ABS control unit (40).Unpin control unit connector X1171 anddismantle it.Insert branch cable C5 and C6 in the into theplug-in guide (41).

Note instructions for automatic cars withM62 B44 engine and DSC, from productiondate 9/97 to production date 9/98 on the nextpage.

Plug in branch cable C5, 1-pole blade terminalcontact, cable colour yellow/red, in PIN9 of thecontrol unit connector X1171. If PIN9 is alreadyassigned, the contact of branch cable C5 mustbe cut off and the yellow/red cable in the spaceof the ABS connector must be soldered to thecable of PIN9 and insulated.Plug in branch cable C6, 1-pole blade terminalcontact, cable colour yellow/white, in PIN42 ofthe control unit connector X1171. If PIN42 isalready assigned, the contact of branch cable C6must be cut off and the yellow/white cable inthe space of the ABS connector must besoldered to the cable of PIN42 and insulated.Reassemble control unit connector X1171 andplug it onto the ABS control unit (40).Install ABS control unit (40) and fastensupplementary wiring harness for navigation Cwith cable straps (26).


C3C4

C7C8

C

40

41

C5C6

C

X117130

26

F 38 0409 B

EN/64


Only for automatic cars with M62 B44 engineand DSC, from production date 9/97 toproduction date 9/98Plug in branch cable C5, 1-pole blade terminalcontact, cable colour yellow/red, in PIN72 of thecontrol unit connector X1171. If PIN72 is alreadyassigned, the contact of branch cable C5 mustbe cut off and the yellow/red cable in the spaceof the ABS connector must be soldered to thecable of PIN72 and insulated.Plug in branch cable C6, 1-pole blade terminalcontact, cable colour yellow/white, in PIN73 ofthe control unit connector X1171. If PIN73 isalready assigned, the contact of branch cable C6must be cut off and the yellow/white cable inthe space of the ABS connector must besoldered to the cable of PIN73 and insulated.Reassemble control unit connector X1171 andplug it onto the ABS control unit (40).Install ABS control unit (40) and fastensupplementary wiring harness for navigation Cwith cable straps (26).


EN/65

C3C4

C7C8

C

40

41

C5C6

C

X117130

26

F 38 0451 B

9. Choose installation of the supplementary wiring harness for navigation in vehicles from production date 9/98


PIN35

PIN18

X1170

40

F 38 0410 B

EN/66

Illustration shows engine compartment, frontright.

Unplug the black 42-pole connector X1170 fromthe hydraulic unit ABS (40) in the enginecompartment, front right. Open it and checkwhether PIN18 and PIN35 are assigned.

If PIN18 and PIN35 are not assigned, installationof the supplementary wiring harness fornavigation should be carried out as described inChapter 10.Chapter 10. Install supplementary wiring harnessfor navigation in vehicles from production date9/98 (PIN18 and PIN35 at connector of the ABShydraulic unit not assigned).

If PIN18 and PIN35 are assigned, installation ofthe supplementary wiring harness for navigationshould be carried out as described in Chapter 11.Chapter 11.Install supplementary wiring harnessfor navigation in vehicles from production date9/98 (PIN18 and PIN35 at connector of the ABShydraulic unit assigned)

If PIN18 is assigned and PIN35 not assigned,installation of the supplementary wiring harnessfor navigation should be carried out as describedin Chapter 12.Chapter 12. Install supplementary wiring harnessfor navigation in vehicles from production date9/98 (PIN18 assigned and PIN35 not assigned atconnector of the ABS hydraulic unit).

If PIN18 is not assigned and PIN35 assigned,installation of the supplementary wiring harnessfor navigation should be carried out as describedin Chapter 13.Chapter 13. Install supplementary wiring harnessfor navigation in vehicles from production date9/98 (PIN18 not assigned and PIN35 assigned atconnector of the ABS hydraulic unit)

10. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 and PIN35 at connector of the ABS hydraulic unit not assigned)


EN/67

Clip in branch cable C1, black 6-pole pinhousing, of the supplementary wiring harness fornavigation C to the existing plug-in connector(40) at the taillight cup (41), rear left.Install supplementary wiring harness fornavigation C along the closing panel to the rightside part. Fasten supplementary wiring harnessfor navigation C with cable straps (26).

41

C

40 C1

26

F 38 0411 B

41

40

C

26

C2-C8

F 38 0412 B

40

X10117

C2

F 38 0413 B




Before further installation of thesupplementary wiring harness for navigation isundertaken, the cover for the control unit box inthe engine compartment, right, should beremoved.

Insulate branch cables C3 to C6 of thesupplementary wiring harness for navigation Cwith shrinkage tubing and tie back in the area ofthe right front sill.Install branch cables C7 and C8 of thesupplementary wiring harness for navigation Cthrough the lead-through grommet in thebulkhead, front right, into the control unit boxand from there onwards to the hydraulic unit ABSand connect them to the black 42-poleconnector X1170 of the hydraulic unit ABS.


C2 C

C3C4

C8C7

C6 C5

F 38 0414 B

C4

C3 C6C5

C

40

30

26

F 38 0415 B

Illustration shows the area behind the glovebox in a left-hand drive vehicle.You shouldproceed in the identical sequence for right-handdrive vehicles.

Feed the supplementary wiring harness fornavigation C with branch cables C7 and C8through the lead-through grommet (40) in thebulkhead, front right, to the control unit box inthe engine compartment and fasten with cablestraps (26).Push on a shrinkage tubing (30) for insulation ineach case onto branch cable C3, 1-pole bladeterminal contact, cable colour yellow/red, branchcable C4, 1-pole blade terminal contact, cablecolour yellow/white, branch cable C5, 1-poleblade terminal contact, cable colour yellow/red,and branch cable C6, 1-pole blade terminalcontact, cable colour yellow/white, of thesupplementary wiring harness for navigation C,and shrink them on with hot-air dryer.Then tie back branch cables C3 to C6 in thearea of the right front sill with cable straps (26).

EN/68

Push supplementary wiring harness fornavigation C with branch cables C7 and C8carefully through the rubber grommet (40) andinstall to the hydraulic unit ABS (41).

Having installed the supplementary wiringharness for navigation C, seal the rubbergrommet (40) with silicon (splash-waterprotection).

Decouple the black 42-pole connector X1170 ofthe hydraulic unit ABS and connect branchcables C7 and C8 as follows:

Pin in branch cable C7, 1-pole blade terminalcontact, cable colour yellow/red, into the black42-pole connector X1170 of the hydraulic unitABS in plug-in place PIN35.Pin in branch cable C8, 1-pole blade terminalcontact, cable colour yellow/white, into the black42-pole connector X1170 of the hydraulic unitABS in plug-in place PIN18.Couple black 42-pole connector X1170 againand plug onto hydraulic unit ABS.Then fasten supplementary wiring harness fornavigation C in the area of the enginecompartment with cable straps (26).


BM

W

40C

C8C7 PIN35PIN18

X1170

4126

F 38 0416 B


EN/69


41

C

40 C1

26

F 38 0417 B


41

40

C

26

C2-C8

F 38 0418 B


11. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 and PIN35 at connector of the ABS hydraulic unit assigned)

EN/70

Dismantle light module (40), unpin the black 54-pole socket housing X10117 from the lightmodule (40) and open it.Plug in branch cable C2, 1-pole blade terminalcontact, cable colour white/yellow, into PIN38 ofthe black 54-pole socket housing X10117.Close black socket housing X10117, plug it inand reinstall light module (40).If necessary tie back excessive length of thesupplementary wiring harness for navigation Cbefore branch cable C2.40

X10117

C2

F 38 0419 B


Insulate branch cables C5 to C8 of thesupplementary wiring harness for navigation Cwith shrinkage tubing and tie back in the area ofthe right front sill.In left-hand drive vehicles, install branch cablesC3 and C4 of the supplementary wiring harnessfor navigation C to the joint connector boxbehind the glove box (excess length must be tiedback) and connect to the joint connectorsX10183 and X10184.In right-hand drive vehicles, install branch cablesC3 and C4 of the supplementary wiring harnessfor navigation C behind the heater box to the leftto the joint connector box behind the glove boxand connect to the joint connectors X10183 andX10184.

11. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 and PIN35 at connector of the ABS hydraulic unit assigned)

C2 C

C3C4

C7C8

RHD C3RHD C4

C6C5

F 38 0420 B

EN/71


Push on a shrinkage tubing (30) for insulation ineach case onto branch cable C5, 1-pole bladeterminal contact, cable colour yellow/red, branchcable C6, 1-pole blade terminal contact, cablecolour yellow/white, branch cable C7, 1-poleblade terminal contact, cable colour yellow/red,and branch cable C8, 1-pole blade terminalcontact, cable colour yellow/white, of thesupplementary wiring harness for navigation C,and shrink them on with hot-air dryer.Then tie back branch cables C5 to C8 in thearea of the right front sill with cable straps (26).Plug branch cable C3, 1-pole blade terminalcontact, cable colour yellow/red, onto the jointconnector X10183 (cable colour at jointconnector yellow/red) in the joint connector box(40) behind the glove box.Plug branch cable C4, 1-pole blade terminalcontact, cable colour yellow/white, onto the jointconnector X10184 (cable colour at jointconnector yellow/white) in the joint connectorbox (26) behind the glove box.Any excessive lengths of branch cables C3 andC4 should be tied back with cable straps (26).

C4

C3C6

C5

C

C8

40

C7

30

26

F 38 0421 B



12. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 assigned and PIN35 not assigned at connectorof the ABS hydraulic unit)

41

40

C

C1

26

F 38 0422 B

41

40

C

26

C2-C8

F 38 0423 B


EN/72


40

X10117

C2

F 38 0424 B


12. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 assigned and PIN35 not assigned at connector of the ABS hydraulic unit)

EN/73

C2 C

RHD C3RHD C4

C3C4

C8C7

C6C5

F 38 0425 B

Before further installation of thesupplementary wiring harness for navigation C,you should remove the cover for the control unitbox in the engine compartment, right.

Install branch cables C7 and C8 of thesupplementary wiring harness for navigation Cthrough the lead-through grommet in thebulkhead, front right, into the control unit boxand from there onwards to the hydraulic unitABS.Connect only branch cable C7, 1-pole bladeterminal contact, to the black 42-pole connectorX1170 at PIN35 of the hydraulic unit ABS.Insulate branch cable C8, 1-pole blade terminalcontact, with shrinkage tubing and tie it back. Inleft-hand drive vehicles, install branch cables C3and C4 of the supplementary wiring harness fornavigation C to the joint connector box behindthe glove box.In right-hand drive vehicles, install branch cablesC3 and C4 of the supplementary wiring harnessfor navigation C behind the heater box to the leftto the joint connector box behind the glove box.Insulate branch cable C3, 1-pole blade terminalcontact, with shrinkage tubing and tie it back.Connect only branch cable C4, 1-pole bladeterminal contact, to joint connector X10184.Insulate branch cables C5 and C6 of thesupplementary wiring harness for navigation Cwith shrinkage tubing and tie back in the area ofthe right front sill.


12. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 assigned and PIN35 not assigned at connector of the ABS hydraulic unit)

EN/74

C4

C3 C6C5

41

C

40

30

26

F 38 0426 B


Feed the supplementary wiring harness fornavigation C with branch cables C7 and C8through the lead-through grommet (40) in thebulkhead, front right, to the control unit box inthe engine compartment and fasten with cablestraps (26).Push on a shrinkage tubing (30) for insulation ineach case onto branch cable C3, 1-pole bladeterminal contact, cable colour yellow/red, branchcable C5, 1-pole blade terminal contact, cablecolour yellow/red, and branch cable C6, 1-poleblade terminal contact, cable colour yellow/white,of the supplementary wiring harness fornavigation C, and shrink them on with hot-airdryer.Plug branch cable C4, 1-pole blade terminalcontact, cable colour yellow/white, onto the jointconnector X10184 (cable colour at jointconnector yellow/white) in the joint connectorbox (41) behind the glove box.Then tie back branch cables C3, C5 and C6 inthe area of the right front sill with cable straps (26).


Seal the rubber grommet (40) with silicon(splash-water protection) after installation of thesupplementary wiring harness for navigation C.

Decouple the black 42-pole connector X1170 ofthe hydraulic unit ABS and connect branch cable C7 as follows:

Pin in branch cable C7, 1-pole blade terminalcontact, cable colour yellow/red, into the black42-pole connector X1170 of the hydraulic unitABS in plug-in place PIN35.Push onto branch cable C8, 1-pole bladeterminal contact, cable colour yellow/white, ashrinkage tubing (30) for insulation and shrink iton with a hot-air dryer.Couple black 42-pole connector X1170 againand plug onto hydraulic unit ABS.Then fasten supplementary wiring harness fornavigation C in the area of the enginecompartment with cable straps (26).

BM

W

40C

C8C7 PIN35

X1170

4126

30F 38 0427 B



13. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 not assigned and PIN35 assigned at connectorof the ABS hydraulic unit)

41

C

40 C1

26

F 38 0428 B

41

40

C

26

C2-C8

F 38 0429 B

40

X10117

C2

F 38 0430 B



EN/75


Before further installation of thesupplementary wiring harness for navigation C,you should remove the cover for the control unitbox in the engine compartment, right.

Install branch cables C7 and C8 of thesupplementary wiring harness for navigation Cthrough the lead-through grommet in thebulkhead, front right, into the control unit boxand from there onwards to the hydraulic unitABS.Insulate branch cable C7, 1-pole blade terminalcontact, with shrinkage tubing and tie it back.Connect only branch cable C8, 1-pole bladeterminal contact, to the black 42-pole connectorX1170 at PIN18 of the hydraulic unit ABS.In left-hand drive vehicles, install branch cablesC3 and C4 of the supplementary wiring harnessfor navigation C to the joint connector boxbehind the glove box.In right-hand drive vehicles, install branch cablesC3 and C4 of the supplementary wiring harnessfor navigation C behind the heater box to the leftto the joint connector box behind the glove box.Connect only branch cable C3, 1-pole bladeterminal contact, to joint connector X10183.Insulate branch cable C4, 1-pole blade terminalcontact, with shrinkage tubing and tie it back.Insulate branch cables C5 and C6 of thesupplementary wiring harness for navigation Cwith shrinkage tubing and tie back in the area ofthe right front sill.

13. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 not assigned and PIN35 assigned at connector of the ABS hydraulic unit)

C2 C

RHD C4RHD C3

C4C3

C8C7

C6C5

F 38 0431 B

EN/76



Feed the supplementary wiring harness fornavigation C with branch cables C7 and C8through the lead-through grommet (40) in thebulkhead, front right, to the control unit box inthe engine compartment and fasten with cablestraps (26).Push on a shrinkage tubing (30) for insulation ineach case onto branch cable C4, 1-pole bladeterminal contact, cable colour yellow/white,branch cable C5, 1-pole blade terminal contact,cable colour yellow/red, and branch cable C6,1-pole blade terminal contact, cable colouryellow/white, of the supplementary wiringharness for navigation C, and shrink them onwith hot-air dryer.Plug branch cable C3, 1-pole blade terminalcontact, cable colour yellow/red, onto the jointconnector X10183 (cable colour at jointconnector yellow/red) in the joint connector box(41) behind the glove box.Then tie back branch cables C4, C5 and C6 inthe area of the right front sill with cable straps (26).

13. Install supplementary wiring harness for navigation in vehicles from production date 9/98 (PIN18 not assigned and PIN35 assigned at connector of the ABS hydraulic unit)

C4

C3 C6C5

C

40

41

30

26

F 38 0432 B

BM

W

40C

C8C7PIN18

X1170

4126

30 F 38 0433 B


Having installed the supplementary wiringharness for navigation C, seal the rubbergrommet (40) with silicon (splash-waterprotection).

Decouple the black 42-pole connector X1170 ofthe hydraulic unit ABS and connect branch cable C8 as follows:Pin in branch cable C8, 1-pole blade terminalcontact, cable colour yellow/white, into the black42-pole connector X1170 of the hydraulic unitABS in plug-in place PIN18.Push onto branch cable C7, 1-pole bladeterminal contact, cable colour yellow/red, ashrinkage tubing (30) for insulation and shrink iton with a hot-air dryer.Couple black 42-pole connector X1170 againand plug onto hydraulic unit ABS.Then fasten supplementary wiring harness fornavigation C in the area of the enginecompartment with cable straps (26).

EN/77


Place retaining plate (7) on the GPS antenna (5)and attach it with expanding rivets (24).

14. Install navigation system

F 38 0434 B

5

724

23

4041

F 38 0435 B

D15

4023

D

26

F 38 0436 B

40

41

42

F 38 0437 B

Illustration shows rear window shelf, left.

Check that existing attachments points (40) areØ 8 mm.If necessary rebore attachment points to Ø8 mm.Take out pre-punched cut-out (41) under the rearwindow shelf and press in attachment grommets(23) into the attachment points (40).

Plug together branch cable D1, coaxial pinhousing, of the antenna extension for GPSantenna D, with the antenna cable (40) of theGPS antenna (5).Insert retaining plate with mounted GPS antennainto the attachment grommets (23) and installantenna extension for GPS antenna D along theoriginal wiring harness to the designatedinstallation location of the navigation computer(in the boot, rear left above) and fasten with cablestraps (26).

Illustration shows boot, rear left above.

Remove retaining nuts M6 (40) and dismantleinstalled trim-panel bracket (41) (is no longerrequired).Remove retaining clip (42) from the trim-panelbracket (41).Retaining nuts M6 (40) and retaining clip (42) areto be further used when installing the bracket ofthe navigation computer.

EN/78


Put plug-in nuts M5 (22) on to the bracket for thenavigation computer (19).


F 38 0438 B

22

19

27

4029B

B5 B619

F 38 0439 B

Place navigation wiring harness B, as shown, inthe supplied cable duct (29) and close all tabs (40).Insert both AW cable straps (27) in the bracketfor navigation computer (19).Place cable duct (29), as shown, in the AW cablestraps (27) and close the AW cable straps (27).Push branch cable B5, blue 18-pole sockethousing, and branch cable B6, Bordeaux-coloured 18-pole socket housing, of thenavigation wiring harness B, through the bracketof the navigation computer (19).

EN/79


Illustration shows boot, rear left above.

Separate off the pre-punched cut-out in theinsulating mat in the side part, rear left.Loosen the basic carrier (16) somewhat in orderto be able to install the bracket of the navigationcomputer (19).Slide in bracket of navigation computer (19) withits pre-mounted navigation wiring harness B andscrew it on with the existing nuts M6 (49) andthe hexagon bolts with washers M5x14 (21).Insert existing removed retaining clip (41) in thebracket of the navigation computer (19).Then push branch cables A10 to A13 of the on-board monitor wiring harness A, and branchcable D2, coaxial socket housing, of the antennaextension for GPS antenna D, through thebracket of the navigation computer (19).

Tie back branch cable A10, white 18-polesocket housing, branch cable A12, angledcoaxial socket housing, and branch cable A13,angled coaxial socket housing, of the on-boardmonitor wiring harness A with cable straps (26)to the on-board monitor wiring harness A.Tie back branch cable B5, blue 18-pole sockethousing, of the navigation wiring harness B, alsowith cable strap (26) to the navigation wiringharness B.


16B6

A13A12A11

A10

4119

B5

40A D

40 B

26 D2

21

F 38 0440 B

17

21

22F 38 0441 B

Put three plug-in nuts M5 (22) on at thedesignated places and screw the bracket of thevideo module (17) to the plug-in nuts M5 (22)with three hexagon bolts with washers M5x14 (21).

EN/80


Engage the retaining clip (6) with the clipped-inbranch cables A9, black 10-pole pin housing,and A14, natural-coloured 6-pole pin housing. ofthe on-board monitor wiring harness A to thebracket of the video module (17).Plug branch cable B2, black 6-pole sockethousing, of the navigation wiring harness B, ontobranch cable C1, black 6-pole pin housing, ofthe supplementary cable for navigation C.Plug branch cable B1, natural-coloured 6-polesocket housing, of the navigation wiring harness B, onto branch cable A14, natural-coloured 6-pole pin housing, of the on-boardmonitor wiring harness A.Plug branch cable B4, black 10-pole sockethousing, of the navigation wiring harness B, ontobranch cable A9, black 10-pole pin housing, ofthe on-board monitor wiring harness A.

Additional installed wiring harness should befasten with cable straps (26) to the original wiringharness.

In vehicles which are equipped with BasicInterface Telephone 2 (BIT2), plug togetherbranch cable B3, black 6-pole pin housing, ofthe navigation wiring harness B, with the black6-pole socket housing of the Basic InterfaceTelephone (BIT2) wiring harness.In vehicles without Basic Interface Telephone 2(BIT2), insulate and tie back branch cable B3,black 6-pole pin housing, of the navigation wiringharness B.


EN/81

B

B2

26B16

17

A14A9

B3

B4

CC1

F 38 0442 B


Cut out supplied template (32) and place it onthe boot trim panel, left (40).Mark cut-out for navigation computer (41) andmake cut-out in the boot trim panel, left (40.Then install boot trim panel, left (40).

Feed out through the aperture for thenavigation computer (41) branch cable A11, blue18-pole socket housing, of the on-board monitorwiring harness A, with the tied back branchcables A10, A12 and A13, as well as branchcable B6, Bordeaux-coloured 18-pole sockethousing, of the navigation wiring harness B, withthe tied-back branch cable B5 and branch cableD2, coaxial socket housing, of the antennaextension for the GPS antenna D.


B

A10 A DA13

A12

D2

40

A11

B6

B5

41 32

F 38 0443 B

2819

A11

18B6

D2

D

F 38 0444 B

Push in cover frame (28) into the aperture until alldetents in the bracket of the navigationcomputer (19) have engaged.Plug in branch cable A11, blue 18-pole sockethousing, of the on-board monitor wiring harness A, into the blue 18-pole pin housing ofthe navigation computer (18).Plug in branch cable B6, Bordeaux-coloured 18-pole socket housing, of the navigation wiringharness B, into the Bordeaux-coloured 18-polepin housing of the navigation computer (18).Plug in branch cable D2, coaxial socket housing,of the antenna extension for GPS antenna D, intocoaxial pin housing of the navigation computer(18).

Make sure that the cables or leads behindthe navigation computer are not jammed ordamaged.

Then insert the navigation computer (18) in thecover frame (28) and engage it.

EN/82


EN/83

15. Coding and finalising operations

If the video module and TV amplifiers forTV function are to be fitted additionally in thevehicle, the Coding and Finalising operations should be carried out after the video moduleand TV amplifiers forTV function have been fitted.

Coding

This system is coding-relevant.

So that the retrofit system– is fully functional and– in association with the other electrical vehicle systems excludes malfunctions and faults,

a coding of this retrofit system, and if necessary other vehicle components, must be carried out and stored in the central coding key of the IKE.

This coding is carried out automatically with the respective current coding programme in the"Retrofit" path.The sequence is operator-guided and you should note the relevant text instructions whencarrying out the individual steps.

Procedure:

– Connect DIS/MoDIC to the vehicle– Ignition "ON"– Selection "Coding ZCS"– Confirm input data with "Y" (only with MoDIC)– Series: "E38"– Path: "2 Retrofit"– System: "8 Navigation"

A "Navigation CD-ROM Operating software V16" is necessary for loading the operatingsystem.Caution! Do not put the CD-ROM "Operating software" yet in the CD drive! Put theCD-ROM"Operating software" in only when told to do so on the on-board monitor.The languagecoding is carried out simultaneously with this CD-ROM "Operating software".

– Start automatic coding (confirm with "Y")– Follow the instructions on the on-board monitor– Print out new master label of the changed coding key and stick it in the vehicle boot on the

right in the area of the battery– After the message "Coding ended" on the screen of the DIS/MoDIC, ignition "OFF", wait

for at least 10 seconds and then ignition "ON" again.– Print out error memory– Insert CD-ROM "Road map" in the navigation computer– Carry out function test.


EN/84

15. Coding and finalising operations

In vehicles with DSP amplifier, the DSP amplifier must be newly coded in addition.

Procedure:

– Connect DIS/MoDIC to the vehicle– Ignition "ON"– Selection "Coding ZCS"– Confirm input data with "Y" (only with MoDIC)– Series: "E38"– Path: "1 Recoding"– System: "82 DSP "– Start automatic coding (confirm with "Y")– After the message "Coding ended" on the screen of the DIS/MoDIC, ignition "OFF",

wait for at least 10 seconds and then ignition "ON" again.– Print out error memory– Carry out function test.

Language coding

The language coding can be carried out again via the "Navigation CD-ROM Operatingsoftware V16".

Finalising operations

Connect batteryCarry out function testPrint out error memoryReassemble the vehicle in the reverse order of disassembly.

16. Connection description forTV function

This chapter should only be taken note of if the vehicle is to be additionally equipped withTV function.

To be in a position to equip the vehicle with TV function, the necessary parts (video module,TV amplifiers, small parts) have to be ordered separately with reference to the Electronic PartsCatalogue (EPC) and fitted.The relevant branch cables of the wiring harnesses have to be connected also as follows:

Undo the tied-back branch cable A4, angled coaxial socket housing, of the on-board monitorwiring harness A, and plug it on to the previously mounted left TV amplifier in the left C-pillar.Undo the tied-back branch cable A13, angled coaxial socket housing, of the on-board monitorwiring harness A, and plug it on to the previously mounted right TV amplifier in the right C-pillar.Unplug branch cable A11, blue 18-pole socket housing of the on-board monitor wiringharness A from the navigation computer.Undo the blue 18-pole socket housing tied back to branch cable B5 of the the navigationwiring harness B, and plug it into the blue 18-pole pin housing at the navigation computer.Undo branch cables A10, white 18-pole socket housing, A12, angled coaxial socket housingand A13, angled coaxial socket housing (all tied back to the on-board monitor wiring harness A).Then install branch cables A10 to A13 to the video module and plug into the video moduleas follows:Plug in branch cable A10, white 18-pole socket housing, at white 18-pole pin housing of thevideo module.Plug in branch cable A11, blue 18-pole socket housing, at blue 18-pole pin housing of thevideo module.Plug in branch cable A12 and A13, angled coaxial socket housing, at the two coaxial pinhousings of the video module.

Should the vehicle be equipped at a later date with TV function, the system must benewly coded. For coding see Chapter 15 "Coding and finalising operations".


EN/85

0,5

VIR

T1,

5R

TGN

0,35

SW

WS

0,5

WS

GR

GE

R<

46

I-B

US

TA

A3

0<

69

34

51

X153

2SR

AD

IO/H

IFI

X129

0V

B 3

0<

69

- RA

DIO

/HIF

I

X130

16M

AS

SE

ST

ER

EO

/HIF

I- R

AD

IO/H

IFI

X129

1V

B R

A4

6

- RA

DIO

/HIF

I

X581

VB

TA

CH

O A

- RA

DIO

/HIF

I

X183

44V

B I

-BU

S

- RA

DIO

/HIF

I

0,75

BR

31

E<

RA

D

2

A1

97

0,35

SC

HIR

M0,

35S

CH

IRM V

MG

VM

R3

1V

MR

VM

G3

1

14

51

67

TA

PE

R+

TA

PE

L-

TA

PE

L+

TA

PE

R-

21

76

0,5

GE

BR

0,5

GE

RT

VM

-V

M+

51

0

0,75

BR

OR

0,75

GE

RT

RA

DL

V-

RA

DL

V+

81

0,75

BR

OR

0,75

BLR

T

RA

DR

V-

RA

DR

V+

11

2

0,75

BR

OR

0,75

GE

SW

RA

DL

H-

RA

DL

H+

12

3

0,75

BR

OR

0,75

BLS

W

RA

DR

H-

RA

DR

H+

14

6

1,5

RTG

N0,

5W

S

30

<6

9A

NT

91

6

I-B

US

7

TA

A5

8G

10

13

R<

ET

EL

M

54

31

E<

RA

D

15

0,5

WS

GR

GE

0,35

SW

WS

0,5

GR

RT

1,5

VIR

T0,

35W

SB

R2,

5B

R

30

<6

9

9

RA

DL

V-

RA

DL

V+

RA

DR

V-

RA

DR

V+

RA

DL

H-

RA

DL

H+

RA

DR

H-

RA

DR

H+

AN

T

81

11

21

23

14

61

6

I-B

US

TA

A5

8G

R<

ET

EL

M3

1E

<R

AD

71

01

35

41

5

1,5

RTG

N0,

5W

SG

RG

E0,

35S

WW

S0,

5G

RR

T1,

5V

IRT

13

93

90

3.9

LT

G V

ER

DR

ILL

T1

39

39

04

.9L

TG

VE

RD

RIL

LT

13

93

90

5.9

LT

G V

ER

DR

ILL

T1

39

39

06

.9L

TG

VE

RD

RIL

LT

13

86

69

9.9

LT

G V

ER

DR

ILL

T

13

86

69

8.9

LT

G V

ER

DR

ILL

T1

38

66

96

.9L

TG

VE

RD

RIL

LT

TA

PE

R+

TA

PE

L-

TA

PE

L+

TA

PE

R-

91

04

3

PL1

2

0,5

SW

0,5

BLS

W0,

5B

LBR

0,5

GE

SW

0,5

GE

BR

54

32

1 0,35

SW

0,35

SC

HIR

M

0,35

SW

0,35

SW

76

0,5

BR

RT

PL1

2

VM

B3

1V

MB

VM

LC

31

12

15

6

VM

GV

MR

31

VM

RV

MG

31

VM

B3

1V

MB

VM

LC

31

17

24

21

3.9

LT

G1

-AD

R.G

ES

CH

.1

72

42

13

.9L

TG

1-A

DR

.GE

SC

H.

17

24

21

3.9

LT

G1

-AD

R.G

ES

CH

.

30

<6

9

8

R<

46

30

<6

9

11

7

0,5

RTG

N0,

5V

IRT

0,5

RTG

N

I-B

US

60,5

WS

GR

GE

58

G 10,5

GR

RT

10

11

31

E<

RA

D

0,5

BR

31

E<

RA

D

0,5

BR

91

8

VM

+V

M-

0,5

RTG

N

30

<6

9

1

0,5

RTG

N

30

<6

9

2

0,5

WS

GR

GE

I-B

US

3

SY

NC

JNA

VG

JNA

VB

RG

BG

ND

54

32

JNA

VR

1 0,5

RT

0,5

SW

0,5

BR

0,5

OR

VO

ICE

GN

DV

OIC

E

76 0,

5B

LRT

0,5

BLB

R

SY

NC

JNA

VG

JNA

VB

RG

BG

ND

JNA

VR

VO

ICE

GN

DV

OIC

E

78

16

17

18

12

3

0,5

SC

HIR

M13

86

69

7.9

LT

G V

ER

DR

ILL

T1

45

91

09

.4L

TG

4-A

DR

.GE

SC

H.

X180

4SR

AD

IO/H

IFI

X188

06R

AD

IO/H

IFI

X129

0V

B 3

0A

69

30

<6

9

RA

DIO

/HIF

I

X129

1V

B R

A4

6

R<

46

RA

DIO

/HIF

IX1

8344

- I-B

US

RA

DIO

/HIF

IX1

436

- 58

G

RA

DIO

/HIF

I

X188

01R

AD

IO/H

IFI

X188

04R

AD

IO/H

IFI

X188

05R

AD

IO/H

IFI

X129

0V

B 3

0A

69

- RA

DIO

/HIF

I

X183

44V

B I

-BU

S

- RA

DIO

/HIF

I

X143

6V

B 5

8G

- RA

DIO

/HIF

I

X581

VB

TA

CH

O A

- RA

DIO

/HIF

I

X129

1V

B R

A4

6

- RA

DIO

/HIF

I

X181

26R

AD

IO/H

IFI

X650

0SR

AD

IO/H

IFI

N9

A1

96

X130

16M

AS

SE

ST

ER

EO

/HIF

I- R

AD

IO/H

IFI

X18

804

X188

02R

AD

IO/H

IFI

X18

802

X130

16M

AS

SE

ST

ER

EO

/HIF

I3

1E

<R

AD

RA

DIO

/HIF

I

X18

806

RADIO

BORDMONITOR

VID

EO

MO

DU

L

31

E<

RA

D

2

F 3

8 0

44

6 B


17. Circuit diagram, on-board monitor wiring harness

EN/86

17. Circuit diagram, on-board monitor wiring harness

Key

A196 On-board monitor

A197 Video module

N9 Radio

X581 Connector speedo A

X1290 Connector 30A69

X1291 Connector RA46

X1436 Connector 58g

X1532 Radio/HiFi navigation

X1804 Plug-in connectornavigation - video module

X6500 Plug-in connector adapter

X13016 Earth stereo/HiFi

X18126 Radio A

X18344 Connector I-Bus

X18801 On-board monitor operating unit

X18802 On-board monitor

X18804 Video module A

X18805 Radio B

X18806 Video module B

Colour abbreviations

BR = brown

RT = red

VI = violet

WS = white

GR = grey

SW = black

GN = green

GE = yellow


EN/87


18. Circuit diagram, navigation system wiring harness

EN/88

0,35

GE

WS

0,35

GE

RT

DF

AH

RD

FA

HL

11

10

0,35

Sch

irm

0,35

WS

GE

GN

DR

XD

CT

SR

TS

TX

DR

FL

16

1

0,35

WS

0,35

SW

0,35

RT

0,35

GR

0,35

VIR

T

13

14

12

R3

1 10

30

0,5

BR

SW

0,5

RTG

N

DF

AH

RG

ND

RX

DC

TS

RT

ST

XD

DF

AH

LR

FL

21

34

13

25

31

R3

0

25

1

0,5

BR

SW

0,35

VIR

T0,

5R

TGN

83

73

29

7.9

LT

G.

GE

SC

HL

.

13

86

69

7.9

LT

G.

VE

RD

RIL

LT

MA

NT

EL

LT

G.

83

73

29

7.9

X153

2BN

AV

I

KA

R-K

BB

NA

VIG

AT

ION

HIF

I-K

BB

ST

VB

. V

IDE

OM

OD

UL

I-B

US

0,35

WS

GR

GE

I-B

US

3X1

310B

NA

VI

X133

185

NA

VI

0,35

RT

R7

5 4

0,35

GR

0,35

SW

G7

5B

75

81

3

0,35

SCH

IRM

0,35

WS

RG

BG

ND

SY

NC

15

17

0,5

BLR

T

VO

ICE

9

R7

5G

75

B7

5R

GB

GN

DS

YN

CV

OIC

E

13

25

46

0,5

BLB

R

VO

ICE

GN

D

18

VO

ICE

GN

D

7X1

804B

NA

VI

X131

3N

AV

I

ST

G-N

AV

IGA

TIO

N

A112

13

X131

2N

AV

I3

15

F 3

8 0

44

7 B

18. Circuit diagram, navigation system wiring harness

Key

A112 Plug-in connector, navigation

X13010 KAR navigation

X1312 Navigation A

X1313 Navigation B

X1532 Radio/HiFi-navigation

X1804 Plug-in connectornavigation-video module

X13318 Navigation/telephone


BR = brown

RT = red

VI = violet

WS = white

GR = grey

SW = black

GN = green

GE = yellow


EN/89


19. Circuit diagram, supplementary wiring harness for navigation system

EN/90

NAVIGATION

0,35WSGE

RFSI

3

RFSI

38

LICHTMODUL

X10117SA-LTG

A3

DFAVL

35

STG ABS/DSC

X1170SA-LTG

A65

DFAVR

18

DFAVR

42(73)

STG ABS/ASC

X1171SA-LTG

A52

DFAVL

9(72)

0,35GERT

DFAVL

1

0,35GEWS

DFAVR

2

X10183VB DFAVL

DFAVL

SA-LTG

X10184VB DFAVR

DFAVR

SA-LTG

X001*VB DFAVL

DFAVL

SA-LTG

X002*VB DFAVR

DFAVR

SA-LTG

0,35GERT

0,35GERT

0,35GEWS

0,35GEWS

0,35GERT

X1310SSA-LTG

0,35GEWS

F 38 0449 B


EN/91

19. Circuit diagram, supplementary wiring harness for navigation system

Key

A3 Light module

A52 Hydraulic unit ABS/ASC

A65 Hydraulic unit ABS/DSC

X001* Connector DFAVL

X002* Connector DFAVR

X1170 ABS/DSC

X1171 ABS/ASC

X1310 KAR navigation

X10117 black 54-pole socket housing of the light module

X10183 Joint connector DFAVL

X10184 Joint connector DFAVR

In automatic vehicles with M62 B44 engineand DSC, from production date 9/97 toproduction date 9/98, the DFAVL signal islies on PIN72 and the DFAVR signal onPIN73 of the ABS/ASC control unitconnector X1171.

The items marked * are only valid for thisdiagram. All other items and X-designationscorrespond to the BMW customer servicecircuit diagrams.


BR = brown

RT = red

VI = violet

WS = white

GR = grey

SW = black

GN = green

GE = yellow

bmw parts and accessories installation instructions

Documents