bahauddin zakariya university, multan. - …eproc.punjab.gov.pk/biddingdocuments/51674_tender...
TRANSCRIPT
BAHAUDDIN ZAKARIYA UNIVERSITY, MULTAN.
TENDER DOCUMENT
For
LAB. EQUIPMENT’S FOR THE BUILDING & ARCHITECTURAL ENGINEERING
Last Date of Submission: 25.05.2016
BAHAUDDIN ZAKARIYA UNIVERSITY, MULTAN www.bzu.edu.Pk
Tel.# 9210071-5 Ext.1305
TENDER FORM OF THE BAHAUDDIN ZAKARIYA UNIVERSITY, MULTAN FOR THE YEAR 2015-2016.
Lab. Equipment’s for the Building & Architectural Engineering
ON F.O.R. Basis Advertised Tender No. T/2015-16/129 _
Last Date of Receipt of Tender 25-05-2016 12:30PM _
Date of Tender Opening 25-05-2016 01:30PM _
Tender Price:- Rs.1000/- (Non-refundable) _
Earnest Money @5% on Estimated Amount (Refundable) _
VENUE TENDER: Treasurer Office B.Z. University, MULTAN.
1. All tender must be submitted on their tender document with sealed envelope and addressed to the Treasurer, Bahauddin Zakariya University, Multan.
2. Any offer not received as per terms & conditions of the tender will be rejected.
3. No offer shall be accepted if:
(i) It is received after the time and date fixed for its receipt.
(ii) Received without earnest money from the firms.
(iii) The tender document is unsigned.
(iv) The tender is ambiguous.
(v) The offer is conditional.
(vi) The offer is from a firm, black listed /suspended or removed from the approved list.
(vii) The offer is received by telegram or Fax.
(viii) The offer is received with shorter validity than required in tender enquiry.
(ix) The offer is not conforming to specifications indicated in the tender enquiry.
Detail
Sr. No.
Item/Equipment Earnest Money @5% on Estimated Cost
1. Engineering Material Testing Lab (Geo-Tech + Concrete)
Rs.491500/-
2. Concrete Materials Testing Lab Rs.287850/-
3. Structural Engineering Lab Rs.801850/-
4. Survey Laboratory Rs.36300/-
5. Digital Studio Rs.31300/-
Detail of required items are given below.
Sr. No.
Detail of Required Item/s Qty
Engineering Material Testing Lab (Geo-Tech + Concrete) 2- Speedy moisture tester, 6 g cap. complete with electronic balance,
accessories and carryng case 2
Accessories
Portable pressure calibrator for Speedy moisture tester 1
Moisture tester reagent. 0.4 Kg box 2
5- Top pan digital balance 30000 g cap. x 1 g precision. 230V/50-60Hz/1Ph 1
7- Automatic Mechanical Proctor / CBR Compactor
Digital automatic Proctor/CBR compactor. 230V, 50Hz, 1ph. - For automatic compaction of 100 mm, 150 mm, 4" and 6" dia. moulds - Selectable rammer drop: 300, 305, 450, 457 mm - Blow rate 30 blows/min - Power 740W - Automatic control of compaction cycles confor- ming to EN, ASTM, AASHTO, BS, NF, NLT, CNR-UNI - User defined compaction sequence - Protection guards for operator safety (CE) - Digital touch button console - Unique hammer lifting device to guarantee correct drop height - Modern and reliable design to ensure long working life - Compaction energies and distribution in accor- dance with standards - Noise reduction cabinet available (33-T8500/XUP) - Rammer not included, select 33-T8500/1 for ASTM/ AASHTO standard, or 33-T8500/2 for EN, BS, NLT, NF, DIN standard
2
Accessories
Hammer for 33-T8500 series automatic compactors, 50,8 mm dia. 2495/4535 g conforming to AASHTO, ASTM, CNR, UNI standards
2
8- Dial Gauges
Dial gauge 50 x 0,01 mm 5
9- AUTOMATIC TRIAXIAL SYSTEM WITH SOFTWARE,
EFFECTIVE STRESS AND STRESS PATH
Load Frame
Triaxial Load Frame 50kN cap. 230-110V/50-60Hz/1ph - Conforming to ASTM D2850, ASTM D4767, BS1377:8, NFP94074 Specifications - RS 232 Controls interface for PC remote control - Microprocessor controlled - Advanced stepper motor drive - Infinitely variable speed from 0.00001 to 9.99999 mm/min. - Audible overtravel alarm - Waterproof membrane keyboard - Rapid approach facility - Top quality design to eliminate all vibrations - Stainless steel platen
1
Triaxial Cell
3500kPa Advanced Triaxial cell for 70mm diameter samples with wire outlets for transducers
1
Water-repellent grease, 1 kg box 1
Accessories for Triaxial Cell & 70mm Dia Sample
Pedestal 70mm diameter two pore pressure ports for 70mm triaxial cell 1
Top cap 70mm dia vacuum type 1
Disc perspex 70mm diameter 1
Pair of porous disc 70mm diameter 1
Rubber Membrane 70mm diameter x 235mm long (pack of 10) 2
O ring 70mm diameter (pack of 10) 1
Membrane Placing Tool for 70mm samples 1
O Ring Placing Tool for 70mm samples 1
Three part split former for 70mm diameter samples 1
Two part split mould for 70mm diameter samples 1
Filter Drains (pack of 50) for 70mm samples 2
Filter discs for 70mm dia sample (pack of 100) 1
Hand sampler complete of cutter, wooden dolly and receiver for 70mm samples
1
Pressure System
Water distribution panel for automatic triaxial testing 1
Laboratory air compressor. 8 BAR max constant pressure. 230V/50Hz/1Ph
1
Nylon tubing 6mm bore x 8mm outside diameter, 10 metre length 1
Back & Cell Pressure (3000kPa)
Servo controlled hydraulic actuator with pressures adjustable to 3000 kPa. 110-240,50/60Hz/1ph - Hydraulic piston driven by a ball screw and gear box mounted on a ball slide. - Driven via a stepper motor controlled by the 29- WF4530 RTC Real Time Control box closed loop control system. - Pressure accuracy: +/- 1%
2
Spare bladders 1
Pneumatic pressure controller base system, for Automatic Triaxial apparatus, for pressures up to 1000 kPa. - Electropneumatic control valve for controlling the air pressure proportionally to the electric signal received from RTC Real Time Control box. - Supply pressure: up to 1000 kPa - Output pressure: up to 1000 kPa - Air consumption: 0.1 cu.m/hr
1
pneumatic pressure controller expansion module to control a second pressure line. - Electropneumatic control valve for controlling the air pressure proportionally to the electric signal received from RTC Real Time Control box. - Supply pressure: up to 1000 kPa - Output pressure: up to 1000 kPa - Air consumption: 0.1 cu.m/hr
1
De Airing System
Portable vacuum pump. 220-240V/50-60Hz/1Ph 1
Rubber tube dia 6,5 x 12,5mm, 2m long for vacuum pump. 1
De airing tank, 23lt capacity 1
Valve panel por use with de-airing tank 1
Water trap 1
Electronic Measuring System Load
Submersible Load Cell 10kN capacity, 10V DC, full range output 2 mV, fitted with 25mm diameter ram
1
Transducer extension cable, 12 m length 1
Axial Displacement
Linear potentiometric transducer, 50mm travel, with 6 pin Lumberg connector complete with mounting block
1
Mounting bracket for displacement transducer, to fit 25mm triaxial cell ram (10751, 11001, 11144 and advanced triaxial cells)
1
Transducer extension cable, 12 m length 1
Volume Change
Automatic volume change transducer with automatic flow for remote control. For Automatic Triaxial apparatus. - Controlled by RTC Real Time Control, box. - For the continuous measurement of the volume change during the test - Max operating pressure: 2000 kPa
1
Transducer extension cable, 12 m length 1
Pore Water Pressure
Pressure transducer 0-10 bar 1
De airing block suitable for banded triaxial cells 1
Transducer extension cable, 12 m length 1
Data Acquisition & Management Software (Effective Stress)
RTC, Real time control box, base system to control one Automatic Triaxial apparatus. 11-240 V, 50-60 Hz, ph. - Closed loop control system firmware with 2 pressure control outputs, 2 open and closed valve control outputs, 2 automatic volume change flow control outputs, 1 RS 232 port for triaxial load frame, 1 network Ethernet port. - Management software including system setups, channel management and transducers calibration with export data to a spreadsheet template for printing certificates.
1
Two way open and close solenoid valve for Automatic Triaxial apparatus. - Controlled by RTC Real Time Control box. - Solenoid operating speed: less than 10 ms
2
8 port LAN Hub box to connect the ATD Automatic Triaxial Datalog, RTC Real Time Control box and a PC to the high speed communication and control network.
1
LAN-RS 232 converter to connectthe ATD Automatic Triaxial datalog to the high speed communications and control network.
1
ATD, Automatic Triaxial Datalog, 16 channels data acquisition for Automatic Triaxial apparatus. 110-240V/50-60Hz/1ph. - For broadcasting all transducers value to the RTC Real Time Control box. - Sensors outputs adjustable up to 10 VDC (common to all channels). - Sensors inputs from -10 V to +10 V. - Sensors impedance from 100 Ohm to 10 kOhm. - Real resolution: +/-32000 divisions. - Sempling rate: adjustable up to 10 sample/sec per channel. - Data storage capacity: 8 Mbytes. - Communication ports: RS 232 and USB for data download to PC with software included. - On board firmware for remote management of the logger with Autogeolab software modules. - Expandable to 32 channels by the expansion module.
1
Autogeolab Effective Stress software module for Automatic Triaxial apparatus. - Conforming to BS 1377:8 and ASTM 4764 FEAUTURING: - Saturation with full automatic control . - Isotropic consolidation stage with volume change measurement. - Consolidated undrained triaxial compression with measurement of pore pressure. - Consolidated drained triaxial compression with measurement of volume change. - Non standard shearing of the specimen in exten sion (undrained or drained) - Export test data to a spreadsheet template for processing and plotting.
1
Effective Stress (CU,CD) Triaxial testing Geo-Analysis for MS EXCEL Template according to BS 1377:8
1
Total Stress (UU) Triaxial testing Geo-Analysis for MS EXCEL Template according to BS 1377:7
1
Accessories for Stress Path Tests
Stress Path Software 1
Extension test accessory for rigid connection to the ram of the banded triaxial cell
1
10- Falling Head Apparatus
Falling head permeability cell 1
Accessories
Stand with 4 manometer tubes 1
Soaking reservoir 1
Vacuum control panel for permeameters 1
De-airing tank for water 7 l capacity. 1
Water trap 1
Portable vacuum pump. Free air displacement 90 litres/min. Ultimate vacuum 0,1 mbar. 230V/50-60Hz/1Ph
1
Rubber tube dia 6.5 x 16.5 mm 2 m long, for vacuum pumps 1
11- Constant Head Apparatus
Constant head permeability cell 75 mm dia. 1
Apparatus
Stand with 3 manometer tubes 1
Constant level tank 1
Tamping rod dia 8 x 300 mm 1
12- Particle Size Analysis (Sieves)
203 mm dia ASTM sieve op 3/4" (19.0 mm) 1
203 mm dia ASTM sieve op 1/2" (12.5 mm) 1
203 mm dia ASTM sieve op 1/2" (12.5 mm) 1
203 mm dia ASTM sieve op 7/16" (11.2 mm) 1
203 mm dia ASTM sieve op 3/8" (9.5 mm) 1
203 mm dia ASTM sieve No 4 (4.75 mm) 1
203 mm dia ASTM sieve No 8 (2.36 mm) 1
203 mm dia ASTM sieve No 10 (2.00 mm) 1
203 mm dia ASTM sieve No 16 (1.18 mm) 1
203 mm dia ASTM sieve No 30 (0.600 mm) 1
203 mm dia ASTM sieve No 40 (0.425 mm) 1
203 mm dia ASTM sieve No 50 (0.300 mm) 1
203 mm dia ASTM sieve No 80 (0.180 mm) 1
203 mm dia ASTM sieve No 100 (0.150 mm) 1
203 mm dia ASTM sieve No 200 (0.075 mm) 1
Pan only dia 203 mm 1
Cover only dia 203 mm 1
Wet washing sieve 8"diameter x 4"deep all stainlees steel fitted with 75 micron mesh
1
12" dia ASTM sieve op. 3" 1
12" dia ASTM sieve op. 2 1/2" 1
12" dia ASTM sieve op. 2" 1
12" dia ASTM sieve op. 1 1/2" 1
12" dia ASTM sieve op. 1" 1
12" dia ASTM sieve op. 3/4" 1
12" dia ASTM sieve op. 1/2" 1
12" dia ASTM sieve op. 3/8" 1
12" dia ASTM sieve No 4 1
Pan only dia 12" 1
Cover only dia 12" mm 1
13- Shrinkage Limit Set
Shrinkage limit set 2
14- Field Density Core Cutter
Core cutter set 100 mm dia 2
Core cutter set 150 mm dia 2
15- Sand Replacement set 150 mm 2
200 mm sand replacement set 2
16- Drying Oven with Forced Connection & Digital Thermostate / Control
Forced convection digital laboratory oven, 100 litres cap. 3000W; 230V, 50-60Hz, 1ph. Temperature range from ambient to 200°C. -
1
17- Drying Oven with Forced Connection & Digital Thermostate / Control
Forced convection digital laboratory oven, 220 litres cap. 3000W; 230V, 50-60Hz, 1ph. - Interior made from zinc coated steel, exterior robustly constructed in enamelled steel insulated with 40 to 50 mm thick mineral wool. - Temperature control by precision digital thermoregulator/indicator. - Temperature range from ambient to 200°C. - Supplied complete with 3 shelves.
1
18- Liquid Limit
Liquid limit device with counter ASTM-AASHTO- UNI model. 4
Accessories
Grooving tool ASTM, plastic, pack of 10 4
Other test equipment to perform test
Glass plate 500 x 500 x 10 mm 4
Flexible spatula 160 mm blade 4
Plastic wash bottle 500 ml 4
Porcelain evaporating dish dia. 120 x 50 mm h 4
Moisture content tin dia. 75X30 MM 4
19- Pycnometer
Specific gravity bottle, 24 ml 10
20- Front loading oedometer to BS 1377, ASTM D2435. With lever arm ratios of 9:1 10:1 and 11:1 - Max loading using 11:1 beam ratio: 1848 kg corresponding to 9.061MPa (92.40 kgf/cm²) on 20 cm² specimen (dia. 50.47 mm) - Lever arm with three hanger position - Screw-jack support
2
Accessories
Permeability attachment with 50ml graduated burette 2
Dial gauge 10 mm x 0.002 mm 2
Oedometer bench to accept up to three oedometers. Complete with locking nuts.
2
Permeability cell for 50.47mm diameter samples with upper and lower stones and cutter ring
2
Calibration disc for 50.47mm diameter samples 2
Permeability cell for 50.47mm diameter samples with upper and lower stones and cutter ring
2
24- Soil Prospecting Kit
Hand Auger head 80 mm dia 1
Hand Auger head 100 mm dia 1
Hand Auger head 150 mm dia 1
Spiral Soil Augar head 25 mm dia 1
Dutch Soil Augar head edelman model 70 mm dia 1
Gravel Augar head 150 mm dia 1
Stainless steel Sample tubes dia 38 x 230 mm 12 no 12
Jarring link 1
Hand extruder for sample tubes 38 x 230 mm 1
Extension rods, 1m long no 6 6
T handle 1
Stillson wrench 2 no 2
Chisel 1
Box, Container 1
25- Sampling Equipment to take out undisturbed soil sample 1
for 38 mm dia samples
Plastic end cap for 38 mm dia sample tube 24
28- Heavy Duty Pocket Panetrometer
Stainless steel tip diameter interchangeable 4.5 mm for very hard soil
6.35 mm for medium and hard soil; 8.98 m for soft soil
Measuring range 0 to 10 kgf/cm2 1
29- Pocket Shear Vane Device
Standard 25 mm dia.Vane rane 0-10N/cm2 1
Sensitivity vane adaptor range 0-2 N/cm2
Highy capacity vane adaptor range 0-25N/cm2
Plastic container
User Manaual
30- PH Meters 2
Laboratory pH/mV/C meter
pH range 0 - 14
mV range +1999 (ORP)
C range 0-100
Accuracy at 20 Degree C
pH +0.01
mV range +1 (ORP)
C +0.5
12 Volt DC with 230 V adaptor included
33- Containers
for soil samples and mixing 50
34- Soil Mixer
Sample mixer 5 liters capacity complete with whisk 230 V 50 Hz, 1ph. 1
35- SPT Apparatus
Standard Panetration Test Apparatus with large tripod, standard weight and
1
penetration apparatus
Concrete Materials Testing Lab
1- Vicat test set ASTM method 2
2- Density of Fresh Concrete
Unit weight measure 10 l cap. BS 1
Density of Hardened Concrete
Specific gravity frame 1
Accessories
Craddle for specimens 1
Top pan digital balance 30000 g cap. x 1 g precision. 230V/50-60Hz/1Ph 1
Specific gravity tank plastic 1
Accessory to us same operating system of Density of Asphalt
Density basket 200 mm dia x 200 mm high 1
3- Hand operated flow table for building lime. - Conforming to EN 459-2 and EN 1015-3. - For determining the flow of building lime. - Total mass of movable parts of the table is between 4.2 and 4.5 kg conforming to the standard. - Complete with flow mould, filling hopper and tamper.
1
Accessories
Flow calliper 1
5- Impact testing machine 1
8- TRL Dynamic cone penetrometer. - 8 kg weight, 575 mm drop - 60° cone, 20 mm dia. - Complete with extension shafts, extension rod set, wrenches, adhesive and carrying case for extension rods. (LOCAL MADE)
1
11- Pocket flow meter for concrete 1
12- Ultrasonic pulse velocity tester battery operated - Conforming to EN 12504-4 and ASTM C597 Specifications - Microprocessor incorporated - Frequency range: 24 to 150 kHz - Receiver input impedance: 1 M ohm - RS 232 output - Connectable to oscilloscope - Transit time measurement: from 0.1 to 1999.9 microsecond - Pulse rate: from 1 to 10 per second, selectable - Resolution: 0.1 microsecond - Transmitter output: 800V - The tester is supplied complete with two 54 kHz transducers (transmitter and receiver) with 3 m cable, calibration rod, coupling agent (250 cc bottle), nylon carrying case
1
Accessories
54 kHz testing head with exponential profile 1
Digital oscilloscope 0-60 MHz. 110-230V/50-60Hz/1Ph 1
Spare 3 m. cable for transducers or for oscilloscope connection. 1
15- 3000 kN cap. compression machine, for cubes up to 200 mm and cylinders up to 160x320 mm, WIZARD BASIC digital readout unit. 230 V, 50 Hz, 1 Ph - For concrete cylinders up to 160x320 mm and cubes up to 200 mm - Wizard Basic digital display and processing unit - Conforming to ASTM C39, AASHTO T22 - Accuracy +/- 1% Specifications FRAME -
1
Rigid welded steel construction - Compression platens 285 mm dia., min. hardness 550 HV30 - Max. vertical daylight 350 mm reducible with distance pieces - Max. piston travel 50 mm HYDRAULIC - Dual stage pump for fast piston approach and high pressure (700 bar - 0.5 l/min) for loading - Self compensated adjustable proportional valve for the accurate oil flow control and preset of load rate - Power 750W STRENGTH MEASUREMENT - Wizard Basic, digital display unit - 5 keys membrane keyboard - LCD display 2x16 characters - Resolution 1/32000 - Verification in real time of the load rate - Serial port for PC - Suitable for application of serial printer SAFETY FEATURES - Maximum pressure valve
Accessories
Distance piece dia 200 x 40 mm 1
Distance piece dia 200 x 50 mm 1
Distance piece dia 200 x 100 mm. 1
16- Balances and Moulds
Top pan digital balance 35kg caoacuty x 10g Battery operated with mains adaptor.
1
Cylinder mould dia. 150 x 300 mm 12
Concrete beam form 150 x 150 x 750 mm 3
Concrete beam mould 150 x 150 x 600 mm 3
Heavy duty 150 mm cast iron cube mould to EN 12
18- Elastic Modulus of Concrete 1
Electronic Universal extensometer/compressometer for cylinders, prisms and
cubes. Supplied with short distance piece, adjusting templates and 2 elastic bands
with datalog 8 channel automatic data acquisition and conditioning unit 230 V, 50 hz, 1ph
20- High Capacity Strain Guage Load Cell 1
5000 KN Capacity, High performance Class 1, ASTM E74 Class AA with 1
Micro processor based Digital Tester for force verfication, Memory to store readings
Printer , serial cable and force calibration verification sheet
Repeatability 0.03, Non Linearity and hysteresis + % FS:0.1
22- Concrete tets hammer type N. Aluminium body. Supplied with hard plastic carrying case. Conforming to EN 12504-2 and ASTM C805
3
Accessories
Calibration anvil for concrete test hammer type -N- and -NR- 3
Scale graduated in p.s.i. for the concrete hammer 3
23- Electric poker vibrator. 2300 W. 2000 mm flexible shaft. 220-240V/50-60Hz/1Ph
1
24- Automatic flexure/tension machine. 5 kN cap. 230V, 50Hz, 1ph. - Conforming to ASTM C348 AASHTO T132 - Constant rate of loading - Dual range: 0-1000N by 10N subd., 0-5000N by 50N subd. - Automatic stop at failure - Accepts flexural or briquette specimens - Single lever loading assures high accuracy
1
Accessories
Tensile attachment for briquette 1
Flexure testing attachment ASTM 1
Briquette mould 1
25- Drum type concrete mixer 115 l cap. 230V/50-60Hz/1Ph LOCAL 1
26- Concrete penetrometer 1
27- Laboratory mixer 10 l cap. 230V/50Hz/1PH 1
Accessories
LOCAL
Spare bowl for mixer. 1
Spare whisk for mixer. 1
28- Automatic Recording Vicat Apparatus 1
ASTM, Aime measurementASHTO version for setting
Structural Engineering Lab
1- ACCELROGRAPH
Accelerograph, Strong Motion, 3-Chan., 24-Bit 1
GPS Receiver/Clock 1
Assembly, Cable, GPS to 130 DAS, Ext., 33' (10m) 1
Assembly, Power Supply, AC, for REF TEK Recorders 1
Disk, Flash Memory, 2GB, CF Type, -20C to 60C 1
Assembly, Cable, NET, 130 to Ethernet RJ45 Crossover, 12' 1
Reader, CF I/II/III, External, USB, 2 Slot 1
Software, Command Line GUI, 130-SM 1
Software, Seismic Signal Data Processing, Interactive 1
Software, Data Utilities 1
Manual, Operations, REF TEK Recorders, CD 1
2- SHAKE TABLE
Shake Table II WS with 2 floor AMD , Includes: 1x 1
UPM180-25, 1x Q4, 1x QuaRC W, 2x AMD
complete, 2x UPM1503.
Single Axis Motion. Coupling capability for dual
axis motion with purchase of additional Shake
Table II. 3 Phase Brushless Motor. Portable,
bench top size capability.
2.5g acceleration with 15kg Payload
Controlled via QuaRC W using Simulink as a user interface.
Opens source, fully documented parameters.
Selected as the standard shake table used by the
University Consortium on Instructional Shake Tables (UCIST)
Workstation Components:
Shake Table: Shake Table II
Driving Power Module: UPM180-25
HIL Control Board: Q4 (4 AO,4 AI,4 Encoders)
Real Control Software: QuaRC W
Structural Analysis Accessories:
Structure: 2 Floor Active Mass Damping
Driver Accessories: 2 x 15V,3 A Power Amplifier
(UPM-1503) for driving Active Mass Dampers
3- Servo-Hydraulic Universal Testing Machine 1
Capacity: 1000kN
Comprising:-
1.1 Servo-hydraulic testing machine is double working space structure with piston under set, which has bidirectional differential function to meet universal control of tension, bending and compression test.
1.2 The system has powerful function to meet with the other material.
2.1 Perform tension, compression, flexure/bending and shearing for specimens. Suitable for metal and nonmetal material, such as iron, steel, steel bar, rebar, cement, concrete, rod and so on.
2.2 Specially designing for production, research and student training and industrial laboratory.
Comply with ISO, BS, ASTM and EN or other standards. ASTM E4, EN10002-2, ISO7500, ISO6892, and BS4449:1998 and so on.
Automatic control capability based upon stress, Position or Strain( closed loops control through load cell, extensometer and encoder)
The system adopts hydraulic pressure to drive crosshead rising and downwards.
Load measuring system employed load cell, displacement measuring adopted foreign photoelectrical encoder and extension measuring under USA/PRC superior extensometer.
Compatible PC control and panel operation to provides functions of Up, Down, Stop, Jog up, Jog down and return to original position.
Crosshead position limiter; Emergency switch; the control system can protect automatically once overload, over-currency, over-voltage, over-temperature.
9.1 Automatic return at test completion to ease mounting next specimen.
9.2 Automatic switching of strain control to position control upon extensometer removal.
9.3 Based on DSP technology DCS-300 controller makes closed loop servo control algorithm includes proportional, integral and derivative tuning.
9.4 Data acquisition consists of 8 or more channels of 24-bit A/D convertor, and the frequency reaches to 50Hz.
9.5 Data exchange between hardware and software is via USB1.1 interface.
9.6 Load measurement resolution is over than 1/300000 of maximum range without any steps.
9.7 Load measurement range is from 1% to 100% capacity under grade 1 accuracy. The load accuracy is better than ±1% of reading.
accuracy. The load accuracy is better than ±1% of reading.
10.1 Two-level authorization passwords management.
10.2 Live indication of Load, Position and Strain, simultaneously.
10.3 Peak indication of Load, Position and Strain, during and after test.
10.4 Live indication of Load, Position and Strain Rates during test.
10.5 Live X-Y graph of user-selected curve: Stress vs. Strain; Load vs.
Position; Stress vs. Position; Load vs. Strain; Load vs. Time; Position vs. Time etc.
10.6 Automatic Saving of Transducer information to file for later recall, re-graph & recalculation.
10.7 Automatic Saving of Results to file for statistical computation and export to spreadsheet and database programs: Access and Excel.
10.8 Print Single Test Reports including X-Y graph on a single page
10.9 Select from a predefined analyses including: Peak Load, Peak
Stress, tensile strength, Rp0.2, Rt0.5, ReH, ReL, Elongation Break (manual & automatic) and so on.
10.10 Specimen Geometries of Flat, Round, Cylinder, Square, Tube, Pipe.
10.11 Define, Save and Recall Tests Setups to minimize errors and save Time.
10.12 Select the international units, such as “N”, “kgf”, “lb”, “mm”, “in” or other units.
10.13 Calibration: adjusting hardware of load cell by software, make it meet test standard.
Versatile removable jaws can be changed rapidly to meet variable wider applications in tension test. The bending and compression fixture can be available also.
CE certificate can guarantee your operation safety.
SPECIFICATION
Capacity : 1000kN
Accuracy class : 1
Quantity of columns : 6 columns and 2 leading screw bars
Force range : 1%-100%FS
Load resolution : 1/300000 of capacity, no step
Load measurement accuracy : Better than ±1% of reading
Displacement measurement accuracy: Better than ±1% of reading
Displacement resolution : 0.007mm
Deformation measurement accuracy: Better than ±1% of reading
Stroke speed range : 0-100mm/min
Round specimen diameter : Ф15-Ф60 (mm)
Flat specimen thickness : 0-40(mm)
Maximum compression space : 700mm
Maximum tensile space : 850mm
Distance between columns : 510mm
Diameter of Compression platens: 200x200mm
Ram stroke : 250mm
Mainframe Dimension : 1020×670×2600mm
Oil tank dimension : 1150×600×900mm
Over-load protection : 10% of the Max. loading capacity
Net Weight : 3500kg
Power supply : 4kW(380V±10%), 2kW(220V±10%),50/60Hz
STANDARD ACCESSORIES
Load frame and oil station : 1000kN(Double test space)
Load cell : 1000kN Bidirectional of tension &compression
Controller : DSC-300, SANS
Software : POWERTEST, (English version)
Extensometer : Gauge length: 100mm,Extension: 10mm
Tensile grips : Round bar diameter: Ф15-Ф60 (mm)
Flat bar thickness: 2-40(mm)
Compression platens : 200x200mm
Remote operation panel : It can control the open and close of the jaws,
and the crosshead upward and downward.
Tool kits : Maintenance tool
Manual : Testing machine operation manual and
software(hard copy and CD)
4- Rockwell & brinell hardness tester 1
Compact microprocessor cpntrplled tester for rockwell, & brinell tests of material hardness
Material tests
Rockwell & Brinell hardness tests.
Accessories
1-Brinell microscope :*25 magnification
2-PC Interface software & comms cable
3-Set of additional anvils & indents
4-Flat annvil 200mm, hardened & ground
5-Raised centre spot anvil16 mm, hardened & ground
6-V anvil 70 mm hardened & ground
7-3.175 mm *6.350 mm for softer metals
8-12.7 mm diameter ball indentors for plastics
8- Structure Test Frame (universal) 2
• Material: aluminum
• Dimensions: nett 880 x 850 x 610
mm, packed 0.46 m3
• Weight: nett 12 kg, packed 20 kg
• Bench space required: Approx 1 m3
• Size of experiment window: 700 mm
x 450 mm
• Maximum load: 5 kN
• Self-positioning nuts: 14 off
• Accessories: Allen key
• Textbook: ‘Structural and Stress
Analysis’ by T. H. G. Megson,
Published Butterworth-Heinemann
1995, ISBN: 0340631961
Automatic Data Acquisition System (STR2000)
10- Apparatus for Bending Moments in a beam 2
• Load application: five weight hangers and 150 x 10 g masses
• Hanger supports: 24 loading positions along the beam, 20 mm apart
• Force measurement: electronic load cell
11- Apparatus for reaction in the frame and beams 2
• Portal frames: two, nominally 250
mm x 500 mm, one with a uniform
section, one with a non-uniform
section
• Portal frame material: aluminium
alloy
• Load application: five weight hangers
and 150 x 10 g masses
• Accessories: lead to connect to a
Digital Force Display, vernier, rule
12- Apparatus for Shear Force in the Beams 2
• Load application: five weight hangers and 150 x 10 g masses
• Hanger supports: 23 loading positions along the beam, 20 mm apart
• Force measurement: electronic load cell
Structures Virtual Experimenation
Pack (STRS)
13- Apparatus for the bending Stress in a beam 2
• Test beam: aluminium, T-section
• Load application: 500 N electronic load cell
• Strain measurement: nine strain gauges (with nine dummy gauges) and a
16-way digital strain bridge
• Resolution: 1 microstrain
• Accessories: 150 mm vernier
14- Pin-jointed framework 2
• Bosses: nine universal bosses each connect members at 30, 45 or 60 degrees
• Members: 15 stainless steel, various lengths with strain gauges attached
• Measurement: 16-way digital strain bridge
• Deflection measurement: digital deflection indicator, 0.001 mm resolution
• Loading: 500 N electronic load cell with additional electronic load cells
Unsymmetrical bending & Shear centre
25 Degree Steps, 16 possible angular positions 2
with hand wheel
Variable loads up to 500 g , 5 weight hangers
150mm venire gauge
17- Continuous & Indeterminate beams 2
• Test beams:
– one aluminium alloy ‘rigid’ beam
with a scale, for simply supported
beam experiments
– one aluminium alloy ‘flexible’ beam
for statically indeterminate beam
experiments
• Load cells:
– two 12 N electronic load cells with
sinking knife edges
– one 12 N electronic load cell
with a knife edge and clamped fixing
• Load application: five knife edges, five
weight hangers, 150 x 10 g masses
• Accessories: rule, vernier, four leads to
connect to a Digital Force Display
18- Plastic bending of beams 1
• Specimen beams: three (8 mm x
8 mm x 860 mm)
• Specimen beam material: fully
annealed mild steel
• Load application: 500 N electronic
ring load cell
• Accessories: Vernier, rule, lead to
connect to a Digital Force Display
Specimen Beams Pack
20- Specimens for Testing
Specimens models for testing and demonstration, in shape of beams and frames of standard sizes for the above mentioned apparatus
2
# DESCRIPTION
OF ITEMS
SPECIFICATIONS QTY
Survey Laboratory
11 Plan Digitizer
Measuring Functions Area, Length Segment, Length Continuous, Count, Perimeter, Units, Scale, Auto Scale, Count Scale
2
Calculator Functions Add, Subtract, Divide, Multiply
Units of Measure Inches, Feet, Yards, Miles, Millimeters, Centimeters, Meters, Kilometers, No Units
Roll-Up III Digitizer
Stylus with Tip and Side Switch
LCD Display featuring 16 characters x 2 lines (2.25 in x 0.75 in / 57 mm x 19 mm)
Measuring Menu
Interface Module Cable
Power Supply
9- to 25-pin Adapter
DOS and Windows Drivers
Shipping/Storage Tube with Insert
User's Manual
Optional Accessories: 4-Button MaxVu Cursor; 16-Button MaxVu Cursor; Plan Holders; Deluxe Travel Case.
12 Digitizing Table 36x48
Logic Trace CNC/DXF Software 1
Digitizing Tablet
Pen Stylus and Cursor
Creates DXF, Gcode, HPGL, PDF, Postcript, and SVG graphics files
latest electromagnetic technology
0.01" to 0.002" accuracy
corded or cordless pen stylus or cursor pointer (pen stylus recommended
USB cable
stand/pedestal for the digitizer for changing the height and
13 Plane Table Set Plane table set including, alidade, sprit level, u fork, plumbob, tripod 5
17 Note Book Latest compatiable with 3D imaging and approved survey softwares with all standard accessories
1
19 Prismatic Compass
Brunton Compass With Leather Case , High Accuracy, Clinometer Funtion atleat Least count of 30 seconds
6
20 Chaining Pins Standard size and material 20
21 Trough Compass High Presicion Compass 12
22 Ranging Rods G.I Pipe with Standard Marks and Colors 24
Digital Studio
2 Servers 9Computers)
Intel Quad Core Xeon Processor Latest 3.0 Ghz, 12Mb 1.2 Cache, 2 500GB HDDS, 04GB Ram, DDR2 17” flat Monitor, Key Board, Mouse Wireless Dlink Interface
02
3 Colour Scanners A3 Size 01
10 Sound Speaker 02
11 Sound System SJ-TS82 02
Note: For all the Brands mentioned in this tender (if any), the term “or equivalent” is hereby added and shall be considered as per PPRA rules.
Certificate
1. We / I hereby confirm to have read carefully the terms & conditions of your Tender
Enquiry dated for opening on --------------------- for the purchase of --------------------------.
We agree to abide by all these terms & conditions/instructions.
2. Certified that the prices quoted against advertises tender dated-------------------are not
more than the prices charged from any other purchasing Agencies in the country in the
financial year ------------------ and in case of any discrepancy, we/I hereby undertake to
refund the price charged in excess if and when asked to do so.
3. Certified that the prices quoted by our firm are inclusive of G.S.T and all taxes as per
rules and regulations.
1. NAME OF FIRM--------------------------------------------------------------------
2. ADDRESS------------------------------------------------------------------------------
3. INCOME TAX NO---------------------------------------------------------------------
4. SALE S TAX REGN NO-------------------------------------------------------------
5. NAME OF TENDERER---------------------------------------------------------------
6. NAME OF BANK AND A/C NO.----------------------------------------------------
7. C.N.I.C NO.--------------------------------------------------------------------------------
8. SIGNATURE OF TENDERER -----------------------------------------------------
9. DATE AND STAMP -------------------------------------------------------------------
CRITERIA FOR TECHNICAL EVALUATION OF THE TENDER
The quotation /bid who secure 60% marks will qualify for the competition.
Sr. No. Parameter
Weight age
1 Technical Specification of Product 45%
2. Age of Company/Firm 10%
4. Financial strength of the vender 15%
5. H.R. Strength 05%
6. On site back up support 10%
7. Relevant experience 10%
8. Certified Engineer 05%
Total 100%
TERMS & CONDITIONS
i. Sealed bids are invited for the purchase of Lab. Equipment’s for the Building & Architectural Engineering, B.Z. University Multan.
ii. The interested bidders shall submit their bids under Single stage- two envelope procedures as defined by Govt. of Punjab Procurement Regulatory Authority.
iii. The bidders will submit their bid in the two envelopes shall contain technical and financial proposals separately and clearly marked as “TECHNICAL PROPOSAL” & “FINANCIAL PROPOSAL” in bold letters. The financial proposal should accompany earnest money @5% of the Estimated Cost, in the form of call deposit in favor of the Treasurer, B.Z University Multan.
iv. In the first stage, only the envelopes containing “TECHNICAL PROPOSAL” shall be opened in the presence of bidders (or their authorized representatives) who may like to attend the tender opening meeting.
v. The “TECHNICAL PROPOSAL” shall be evaluated and no amendments in the “TECHNICAL PROPOSAL” permitted.
vi. Financial bid will be opened after the completion of all codal formulation of evaluation of the Technical Bid on the date, and time which will be communicated to the bidders.
vii. Financial bid will be opened for those bidders who submitted their Technical bids OR fulfill the Technical requirement in the presence of the bidders in case any bidder after written call will not be present at the time of opening due to any reason then any claim by him will not be accepted in future. Otherwise their Financial Bids shall be returned un-opened to the respective bidder.
viii. Bahauddin Zakariya University, Multan reserves the right to drop any items given in the tender without assigning any reason and also reserves the right to reject any or all bids.
ix. Sole distributor certificate (if any) should be attached with the bids.
x. The quotations offering sub standard product can be screened out to ensure procurement of - Lab. Equipment’s.
xi. The rates will be valid up for 120-days from the date of opening the tender.
xii. A University Inspection committee will inspect the Lab. Equipment’s and further will recommend for payment.
xiii. The firm must attach photocopy of income tax and Sales Tax Registration with the quotation, otherwise quotation will not be accepted.
xiv. Attached proforma/Certificate should invariable be filled and submitted with the quotation.
xv. All bids should reach the office of Treasurer, Bahauddin Zakariya University, Multan on or before 25.05.2016 at 12:30 p.m. The bids will be opened on the same date at 01:30 p.m.
xvi. Price of each item should be mentioned including GST/ all Taxes in Tender.
xvii. The tender should be quoted on the basis of free delivery of Lab. Equipment’s at the Building & Architectural Engineering, B.Z. University Campus.
xviii. Quotation should be submitted in print output/typed condition preferably.
xix. Conditional bid will not be accepted.
TREASURER UAN. 111229988 Ext.1305