assembly instructions operator's manual parts listshortlineag.com/slmd12 manual.pdf · 2011....

SAKUNDIAK

ASSEMBLY INSTRUCTIONS OPERATOR'S MANUAL

PARTS LIST

SLMD12 MECHANICAL DRIVE AUGER MODEL NO.

SLMD12-2200 SLMD12-2400 SLMD12-2600

OPERATORS MANUAL SLMD12 SERIES

TABLE OF CONTENTS

GENERAL

1 Table Of Contents 2 Sign Off Sheet 3 General Safety

SAFETY

4 Machine Inspection 5 Designated Work Area 6 Safety Guard Description 7 Transport And Placement

OPERATIONS

8 Start Up And Break In 9 Lubrication And Maintenance 10 Safety Decals And Location

ASSEMBLY

13 Set Up Procedure 14 Tube And Truss Assembly 16 Winch Assembly 17 Hitch Assembly 18 Top Lift Frame Assembly 19 Frame Assembly 20 Lift Arm Assembly 21 Feed Tube Assembly 22 Hopper Assembly

PARTS

23 Main Frame Assembly 24 A-Frame Assembly 25 PTO Shaft Assembly 26 Hopper Assembly 28 Feed Auger Head and Tube Assembly 29 Lift Arm Assembly 30 Top Gear Box Assembly 31 Bottom Gear Box Assembly 32 Boot Assembly 34 Tube Assembly- 2200 36 Tube Assembly- 2400 & 2600 38 Truss Assembly 40 Winch Assembly 41 Bolt On Winch Plate Assembly

INDEX

42 Parts Index

WARRANTY

43 Warranty and Disclaimer


SAKUNDIAK GRAIN AUGER SIGN OFF SHEET As a requirement of OSHA, it is necessary for the employer to train the employee in the safe operation and safety

procedures with this auger. We include this sign-off sheet for your convenience and personal record keeping.

DATE EMPLOYER SIGNATURE EMPLOYEE SIGNATURE


GENERAL SAFETY

Watch this symbol. It points out important precautions. It means "ATTENTION - BECOME ALERT!

YOUR SAFETY IS INVOLVED"

Occupational safety is of prime concern to Sakundiak Equipment Ltd. This transport manual was written with the safety of the operator and others who come in contact with the equipment as our prime concern. This manual presents some of the day to day work problems encountered by the operator and other personnel. We wrote this manual to help you understand safe operating procedures for augers. We want you as a partner in the safe operation of our equipment.

It is your responsibility as an owner, operator, or supervisor, to know what specific requirements, precautions and work hazards exist and to make these known to all other personnel working with the equipment or in the area so that they too may take any necessary precautions that may be required.

Failure to read this Transport Auger Manual and it's Safety Instructions is a misuse of the equipment.


SAFETY ALERT SYMBOLS

BE ALERT This symbol is used to call your attention to instructions concerning your personal safety. Watch for this symbol - it points out important safety precautions. It means "ATTENTION - Become Alert! Your Safety Is Involved!" Read the message that follows and be alert to the possibility of personal injury or death.

MACHINE INSPECTION • Check to see that all guards listed in the assembly instructions are in place, secured and functional.

• Check winch and cable for security and operation. There should be at least 3 complete wraps of cable around winch drum in full down position. Cable anchor on winch drum must be tight.

• Are all fasteners tight?

• Are all chains properly adjusted? (See Maintenance Section)

• Check oil levels in gear box. (See Maintenance Section)

OPERATOR QUALIFICATIONS Operation of this transport auger shall be limited to competent and experienced persons. In addition, anyone who will operate or work around a portable auger must use common sense. In order to be qualified, they must know and meet all other requirements, such as:

• Some regulations specify that no one under the age of 16 may operate power machinery. This includes augers and flight type elevators. It is your responsibility to know what these regulations are in your area or situation.

• Current OSHA regulations state in part: "At the time of initial assignment and at least annually thereafter, the employer will instruct every employee in the safe operation and servicing of all equipment with which the employee is, or will be involved.

• Unqualified persons are to stay out of the work areas.

• A person who has not read and understood all the operating and safety instructions is not qualified to operate the machine.


DESIGNATED WORK AREA The following diagrams will show the designated work areas. These areas shall be marked off with colored nylon or plastic rope hung by portable barriers to define the designated work areas.

Under no circumstances should persons not involved in the operation of the equipment be allowed to trespass into the work area.

It shall be the duty of all operators to see that children and or other persons stay out of the work area. Trespass into the area by anyone not involved in the actual operation, or trespass into a hazard area by anyone shall result in an immediate shut down by the operator.

Prior to start up and during operation, it shall be the responsibility of the operators to see that the work area has secure footing, is clean and free from all debris and tools which may cause accidental tripping and/or falling.

CAUTION! A WALKING SURFACE,

ARE THERE THINGS TO TRIP YOU?

\

.. IS IT SLIPPERY?

---- ------- -----------------------------~

i A HAZARD, KEEP OUT, .. AUGER INTAKE AREA.

A KEEPAWAY!

.. OVERHEADW_I_R-ES-~

A HAZARD, KEEP OUT! UNDER AUGER AND UNDERCARRIAGE AREA .

•...................... . WHEELCH7····· ..... _..·········· .. ···· ...

WORKAREA ' AUTHORIZED PERSONNEL ONLY.

....... WHEEL CHOCKS. . ..... . ............ . . . . WHEELCHci~ . . - ·...... .-----· .· / BOTH REAR

WHEELS. A HAZARD, KEEP OUT, .. AUGER DRIVE AREA. SUPPORT DISCHARGE END .


SAFETY GUARD DESCRIPTION

PTO DRIVE GUARD HOPPER FLIGHT GUARD

HOPPER DRIVE GUARD SWING HEAD GUARD


TRANSPORT AND PLACEMENT MOVING THE AUGER WITH THE TOWING VEHICLE TO OR FROM THE WORK AREA.

• Always transport your auger in the full down position. The Tube Assembly should be seated in the A-Frame cradle.

• Make sure that the hitch pin is securely attached and an alternate safety chain is secured to the auger and towing vehicle.

• Ensure Lift Arm Safety Chain is attached to Hopper.

• Once the auger is hitched to the vehicle, ensure that the jack is swung up into the transport position.

• Be alert of overhead obstructions and electrical wires. Electrocution can occur without direct contact. Failure to do so will result in severe injury or death.

• Never allow persons to stand underneath or ride on the auger when it is being transported .

/). KEEPAWAY! .aA OVERHEAD WIRES

II

MOVING THE AUGER WITH THE TOWING VEHICLE INTO OR OUT OF ITS WORKING POSITION.

• Always move an auger with a vehicle, never manually.

• Lift slowly, no higher then the hitch bar. Be sure grain is out of tube and auger is on a level surface.

• Do not place lumber under wheels for increased height.

• Before raising, check for power lines. • When auger is in place, anchor intake end and/or

discharge end and chock wheels. • When in transport or placement, PTO shaft

should be disconnected.

OVERHEAD WIRES KEEP AWAY!


START UP AND BREAK IN

Sakundiak Equipment recommends that you do the following before augering grain with your new auger:

• Run that grain auger at approximately l/2 the normal operating speed (225 rpm with PTO) without adding grain to the intake for approximately 5 minutes.

• Bring auger up to full operation speed (450 rpm with PTO) and slowly add grain to the hopper.

• Continue to add grain slowly until approximately 1000 bushels (28 tonnes) has been loaded through the grain auger. This will "shine up" the flighting and the tube.

• The operator should be aware of any unusual vibrations or noises, determine source and shut down. LOCK OUT POWER SOURCE BEFORE SERVICING OR ADJUSTING.

OLD AUGER START UP AND BREAK IN

Sakundiak Equipment recommends that you do the following before augering grain with your used auger:

• Before positioning the auger, be sure all guards and shields are in place, securely fastened and fully operational.

• Check oil level in gear boxes, fill if necessary and lubricate all grease fittings.

• Ensure PTO shaft is securely fastened. • Check the lift cable before each use and replace if

frayed or damaged .

CAUTION

• Observe work area restrictions (see work area diagram)

• Keep all safety guards and shields in place. • Make certain everyone is clear before operating or

moving the machine. • Keep hands and feet away from all moving parts. • Lock out power source to adjust, service or clean .

EMERGENCY SHUT DOWN

•

•

•

Should the auger be immediately shut down under load, lock out the power source and disconnect PTO shaft. Empty grain from hopper and auger. Starting the auger under load may result in damage to the grain auger. Before restarting, make certain everyone is clear of the designated work area .

Start grain auger at a reduced speed .

NORMAL SHUT DOWN

•

•

Make sure that the hopper and auger are empty before stopping the unit. Lock out power source and remove PTO shaft.

CLEAN UP AND STORAGE

When the operation is completed , it is recommended that you move the auger to the new work area or to a storage area. •

•

•

Remove barriers, anchors and wheel chocks. Clean entire work area. Remove PTO shaft and move auger slowly out of work area. Lower auger to full down position immediately upon clearance of any obstruction.

• The auger should be stored in the full down position. • Do not attempt to pull grain auger out of snow

bank in winter. This will cause damage to the tube assembly.

• Ensure that there is no snow build up on the auger tube while in storage to prevent damage to the auger.

• Store auger with the hopper in the tipped position. • CAUTION! Maintain a minimum 4" lap on the

tumbler shields. Do not engage power take-off until all personnel are clear of tractor, tumbler shaft and auger. Ensure ends are fastened securely to the auger and tractor.

• When installing PTO, ensure CV end goes to tractor.


AUGER LUBRICATION AND MAINTENANCE

DANGER! Do not service or lubricate while the auger is running. LOCK OUT THE POWER SOURCE.

GEAR BOX

• 12 inch grain augers, fill with 1/2 quart (1/2 litre) of #90 gear oil. • Do not over fill gear box. • Change oil once a year. • Grease U-Joint once a day.

HEAD END

• The bearings are pre-lubricated at the factory and have grease fittings for future lubrication.

HOPPER

• All hopper bearings are pre-lubricated and do not require further lubrication. • Grease U-Joint and bushings once daily. • Grease hopper wheels once every season. • Drive chains should be oiled with #130 gear oil once every season.

HOPPER LIFT

• Cable rollers should be oiled once a season.

BOOT DRIVE CHAIN

• The drive chain should be oiled with #130 gear oil once every season.

PTO SHAFT

• PTO shaft and attachment should be greased once a day with a good quality grease.


A CAUTION 1. Do not operate this auger before reading and

understanding the operators manual.

2. Do not operate this auger unless all guards and safety devices are securely in place.

3. Do not adjust, service, lubricate, clean, unclog or move this unit until all power has been shut off.

4. Make certain everyone is clear of the equipment before moving or operating. Never allow children, vis itors or untrained personnel in the area.

5. Keep hands, feet and clothing clear of all moving parts while in operation.

6. Support discharge end or anchor intake end to prevent upending.

7. Empty auger and lower to transport position before moving to prevent upending.

8. Lower this unit to transport position when not in use.

9. When raising or lowering auger watch for overhead powerlines and other obstructions.

10. Disengage belt tension release on motor base before starting motor.

11. Disconnect power on electric motor driven units before resetting motor overload, make certa in electric motors are properly grounded.

12. Always make certain that trained personnel are in attendance while unit is in operation

A DANGER

Y<11 Upending Hazard

The intake end of the auger must always have downward weight.

Always test it before releasing it from the vehicle or holddown.

Lift the intake slowly and keep it no higher than the tractor tow bar when attactching or releasing it.

Immediately lower the auger to transport position before moving.

Failure to do so will cause upending, which will result in serious injury or death.

A CAUTION CLOSE VALVE IN THE LIFT CYLINDER HYDRAULIC LINE AFTER RAISING AUGER INTO POSITION

A WARNING To Prevent Serious Injury or Death

-Avoid unsafe operation or maintenance.

-Do not operate or work on this machine without reading and understanding the operator's manual.

-If manual is lost, contact your nearest dealer for a new manual.

A DANGER ELECTROCUTION HAZARD

~ To prevent serious injury or death from electrocution:

.Stay away from overhead powerlines when transporting or raising augers. This machine is not grounded. Electrocution can occur without direct contact

A CAUTION P.T.O. OPERATION

- Conne~::t C.V. end of P.T.O. to tractor.

·Do not exceed 25 degrees In either direction.

-Disconnect P.T.O. If angle e:o:ceeds more than 25 degrees during alight tum.

-When moving or positioning auger, always disconnect P.T.O. from tra<:tor and place P.T.O. in holder.

-Failure to follow the above list will damage the C.V. joint.

A DANGER

~ ROTATING FLIGHTING

Keep away from intake end. Failure to do so will result in serious Injury or death.

Do not use the auger without Intake guard in place

A WARNING ~~

~@ 40 ~ MOVING PART HAZARD

To prevent serious injury or death from moving parts:

-C lose and secure guards and shields before starting.

-Keep hand, feet, hair, and clothing away from moving parts.

-Disconnect and lockout P:OWer source before adjusting or servicing.

-Do not stand or climb on machine when operating.


A CAUTION P.T.O. OPERATION

@k • Main~in 36" · 38" dis~nce between tractor stub and auger stub by repositioning the adjustable auger hitch.

. Main~in a minimum ""lap on tumbler shields.

A DANGER

.. ]""Q~~r;, ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH KEEP HANDS, FEET HAIR AND CLOTHING

AWAY FROM MOVING PARTS

Do not operate without--AU driveline, tractor and equipment shields in place. -Drive lines securely attached at both ends. -Drive line shields that turn freely on driveline.

AWARNING

~ \~ HIGH PRESSURE FLUID HAZARD

To prevent serious injury or death

- Relieve pressure on system before repairing or adjusting or disconnecting.

-Wear proper hand and eye protection when searching for leaks. Use wood or cardboard instead of hands.

-Keep all components in good repair.


A WARNING A DANGER ~~ 40 ~© ~

MOVING PART HAZARD To prevent serious injury or death from moving parts:

~ TY~~

-Close and secure guards and shields before starting.

-Keep hand, feet, hair, and clothing away ROTATING FLIGHTING from moving parts. Keep away from intake end. Failure to do -Disconnect and lockout power source before adjusting or servicing.

so will result in serious injury or death .

Do not use the auger without intake guard -Do not stand or climb on machine when in pl ace . operating.

A WARNING ~~ 40 ~© ~

MOVING PART HAZARD To prevent serious injury or death from moving parts:

-Close and secure guards and shields before starting.

-Keep hand, feet, hair, and clothing away from moving parts.

-Disconnect and lockout power source before adjusting or servicing.

-Do not stand or climb on machine when operating.


SET UP PROCEDURE Note: Reference to right and left hand used throughout this manual refers to the position standing at the intake enc looking towards the head end.

1.

2.

3.

4.

5.

6.

7.

8.

Follow and complete steps 1 thru 20 on page 14 using page 15 reference drawings and then proceed to step 2 on this page.

Follow and complete steps 1 thru 8 on page 16 and then proceed to step three on this page.

Follow and complete steps 1 thru 4 on page 17 and then proceed to step 4 on this page.



Place assembled (FIG. 9) under assembled (FIG. 1 ). Connect the two assemblies with two 1" dia. x 2-1/2" bolts and lock nuts. NOTE: Refer to (FIG. 1) for top lift frame assembly mounting location. Proceed to step 7 on this page.

Lift the now assembled (FIG. 1 & 9) together and position it over the partially assembled (FIG. 10). Line up bottom of top lift frame to the top of the bottom lift frame. Install a pivot bushing to each side. Fasten the assemblies together at each side with 1" dia. x 8" bolt, two plated washers and a lock nut. Proceed to step 8 on this page.

Raise the auger tube assembly and then continue with steps 7 thru 17 on page 19 before proceeding with step 9 on this page.

9.

10.

11.

12.

13.

14.

15.

TENSION BRACKET #2

FIGURE 14

Follow and complete steps 1 thru 6 on page 20, and then proceed to step 10 on this page.

Hydraulic lines: Short line connected to upper steel hydraulic line and hydraulic cylinder. Connect valve to the lower steel hydraulic line and then attach long line to valve. Complete long line assembly with pioneer tip. Proceed to step 11 on this page.




Check that all bolts are tightened, pins are in place, fittings are greased and that all safety guards and shields are installed. Ensure proper air pressure in all tires.

Ensure Rod is tightened at the bottom hole of Tension Bracket #1 on the side of hopper transport location and at the top hole of Tension Bracket #2 on the opposite side of the hopper transport location. See Figure 14 on this page.

TENSION BRACKET #1

ROD

' OPERATORS MANUAL SLMD12 SERIES

TUBE ASSEMBLY AND TRUSS ASSEMBLY 1. Connect tube assembly A to tube assembly B as

shown in (FIGURE 01) , ensure proper alignment of flight assemblies. Note: For the SLMD12-2400 and SLMD12-2600, there are three tube 14. assemblies to connect.

2. Lift BOOT END of TUBE ASSEMBLY min. 24" high. 15.

3.

4.

Assemble truss risers (FIGURES 03, 04 and 05) in the order indicated in (FIGURE 01).

Position one SHORT CABLE and one LONG CABLE straight and flat on floor and to the left

16.

and right side of the tube assembly. 17.

5. Install SHORT CABLE spanning from (FIGURE 18. 03 to 05) . See (FIGURE 01). Fasten to (FIGURE 05) first using 5/8" dia. bolt, flat washer and bushing. Tighten. 19.

6 . Fasten SHORT CABLE to bottom two holes in (FIGURE 04) using 3/8" cable clamp and nuts. 20. Leave loose.

7. In (FIGURE 03) partially thread one of the two nuts to eyebolt while attaching eyebolt to TUBE SADDLE.

8. Thread SHORT CABLE thru eyebolt and pull tight. Attach two 5/16" cable clamps as shown in (FIGURE 03).

9 . Tighten partially threaded nut on eyebolt until adequate tension is achieved on SHORT CABLE.

10. Thread second nut to eyebolt and lock.

11. Repeat steps 5- 10 to install second SHORT CABLE.

12. Install LONG CABLE spanning from (FIGURE 02 to 06). See (FIGURE 01). Fasten to (FIGURE 06) first using 5/8" dia . bolt, flat washer and bushing. Tighten .

13. Fasten LONG CABLE to top two holes in

(FIGURE 03, 04 and 05) using 3/8" cable clamp and nuts. Leave loose.

In (FIGURE 02) partially thread one of two nuts to eyebolt while attaching eyebolt to TUBE SADDLE.

Thread LONG CABLE through eyebolt and pull tight. Attach two 5/16" cable clamps as shown in (FIGURE 02).

Tighten partially threaded nut on eyebolt until adequate tension is achieved on LONG CABLE.

Thread second nut to eyebolt and lock.

Repeat steps 12- 17 to install second LONG CABLE.

Lower BOOT END to floor and tighten all truss riser cable clamps.

Refer to SET-UP PROCEDURES page 13 step 2 for the next set of instructions.


TUBE ASSEMBLY AND TRUSS ASSEMBLY

BOOT-END

MAIN FRAME ASSEMBLY BASE PLATE TOP LIFT FRAME ASSEMBLY BASE PLATE

FIGURE 01

LONG CABLE

FIGURE 02 FIGURE 03

LONG CABLE

""''"~

SHORT CABLE

FIGURE 04 FIGURE 05 FIGURE 06

1.

2.

3.

4.


WINCH ASSEMBLY Attach item 1 to item 2 with three 3/8" dia. 5. carriage bolts and nuts. Leave loose. See (FIGURE 07).

Install item 4 to item 1. 6.

Position item 5 on item 6 and 4. 7.

Tighten chain by pulling winch assembly towards 8. the head-end and tighten the three carriage bolts from step 1.

Mount items 1 and 2 to item 3 using 1/2" dia. x 8" bolt and lock nut at boot end and 1/2" dia . x 9" bolt and lock nut at head end.

Install item 7 to item 6.

Insert item 8 thru items 7 and 6.


FEED TUBE ASSEMBLY HEAD END (FIGURE 12 &13}

1.

2.


HITCH ASSEMBLY Install item 1 onto item 2 using 5/8" dia U-bolt, 5. washers and lock nuts and three 1/2" dia. bolts and lock nuts at the underside of the tube flange and four 1/2" dia. bolts and nuts at tube base mount. 6.

Insert item 6 into item 2 and lock in place using 7. item 3.

After completion of SET-UP PROCEDURE steps 1 through 10, continue with HITCH ASSEMBLY steps 6 through 9.

Insert item 2 into item 6.

Insert item 7 through items 6 and 2.

8. Insert item 8 through item 7. 3. Insert item 4 through item 3.

4. Refer to SET-UP PROCEDURE page 13 step 4 for the next set of instructions.

FEED TUBE ASSEMBLY HEAD END (FIGURE 12 & 13)

TUBE FLANGE

9. Refer to SET-UP PROCEDURE page 13 step 12 for the next set of instructions.

e HITCHEND \

y ~ \ ,y @) ' ~ /

5/8" DIA. U-BOLT

FIGURE 08

1.

2.

3.

4.


TOP LIFT FRAME ASSEMBLY Lay frame out as shown in (FIGURE 09).

Fasten item 4 to item 5 using 1-1/8" dia. bolt and lock nut.

Connect item 5 to item 3 using 5/8" dia. bolts, washers and nuts.

Connect item 1 to item 3 using 5/8" dia . bolts, washers and nuts.

3

1~

BOTTOM LIFT FRAME ASSEMBLY END

(FIGURE 01)

5.

6.

7.

8.

FIGURE 09





TUBE ASSEMBLY END '0. (FIGURE 01)


FRAME ASSEMBLY 1.

2.

3.

4.

5.

6 .

7.

8 .

Lay frame out as shown in (FIGURE 10). Ensure item 4 (axle) is on jack stands prior to beginning assembly.

Fasten items 6 and 7 to item 4 using 1" dia. bolts and lock nuts.

Install items 8 and 9 to item 6 and 7 using 5/8" dia. bolts and nuts.

Mount tires on rims and mount rims on axle spindles.

Insert items 10 inside of item 4 using items 5 and hairpin.

Refer to SET-UP PROCEDURE page 13 step 6 for next set of instructions.

After completion of SET-UP PROCEDURE steps 1 through 8. Continue with FRAME ASSEMBLY steps 8 through 17 .

Install item 2 to items 1 and 3 using 5/8" bolts.

9. Fasten item 8 to items 6 and 7 using 5/8" dia . U-bolts.

TUBE ASSEMBLY END (FIGURE 01)

10. Fasten item 11 to item 1 using 5/8" dia. x 1-1/2" bolts, lock washer and nut.

11. Fasten item 14 to item 3 using 5/8" dia. x 1-1/2" bolts, lock washer and nut.

12. Install item 12 in top holes of items 11 and 14 using 5/8" dia. x 4" bolt, lock washer and nut.

13. Install item 13 in bottom holes of items 11 and 14 using 5/8" dia. x 4" bolt, lock washer and nut.

14. Place item 15 on top moon shape cut out of item 11.

15. Place item 16 on bottom moon shape cut out of item 14.

16. Slide item 17 through items 16 and 15 and fasten with 1" nut.

17. Refer to SET-UP PROCEDURE page 13 step 9 for next set of instructions.

FIGURE 10

TOP LIFT FRAME ASSEMBLY END

(FIGURE 09)

1.

2.

3 .


LIFT ARM ASSEMBLY Slide LIFT ARM ASSEMBLY into SADDLE ASSEMBLY and fasten in place using items 3 and 5.

Install CABLE ROLLER ASSEMBLY #1 and item 7 on to pin .

Thread cable end from winch around CABLE ROLLER ASSEMBLY #1 and #2 through PIPE and around CABLE ROLLER ASSEMBLY #3 .

2

SAFETY HOOK

CABLE ROLLER / ASSEMBLY #3

PIPE

LIFT ARM ASSEMBLY

4 .

5.

6.

Slide cable through item 2. Locate item 2 7" from cable end . Bend the last 7" of cable back onto itself and fasten using item 1. Locate item 1 4" above item 2.

Slide item 6 over PIN on SADDLE ASSEMBLY and lock in place with item 4.

Refer to SET-UP PROCEDURE page 13 step 10 for the next set of instructions.

CABLE ROLLER ASSEMBLY #2

FIGURE 11


FEED TUBE ASSEMBLY 1.

2.

3.

Assemble item 1 to item 2 with two 5/8" dia. x 1-1/2" UNC bolt c/w lock nut.

Install UNIVERSAL JOINT to top end of GEAR BOX SHAFT.

Push item 3 between items 1 and 2.

5.

6.

7.

4. Fasten item 3 to item 1 and 2 using two items 4.

GEAR BOX SHAFT

/

/"--,

/

FIGURE 12

Install item 5 to item 6.

Attach item 7 to item 2 with three 1/4" dia. x 3/4" whiz bolts c/w whiz nuts.


UNIVERSAL JOINT

2

HOPPER ASSEMBLY END -----" (FIGURE 13)

1.

2.

3.

4.


HOPPER ASSEMBLY Fasten item 3 to item 2 with two 1/2" dia. x 1-1/4" bolts and whiz nuts.

Assemble item 4 to item 5 with three 1/4" dia. x 3/4" whiz bolts and whiz nuts.

Attach item 6 to item 5 using two 1/4" dia. x 3/4" whiz bolts and whiz nuts .

Install item 4, 5 and 6 assembly to item 2 with three 1/4" dia. x 3/4" whiz bolts and whiz nuts. Ensure assembly is pulled towards FEED TUBE ASSEMBLY END before tightening bolts.

FEED TUBE ASSEMBLY END (FIGURE 12)

5.

6.

7.

8.

FIGURE 13

Bolt the four items 1 to item 2 using 3/4" dia . x 8-1/2" bolt, plate washer and lock nut.

Place 3/8" dia . x 1-1/2" bolt through item 3 and set items 7 and 8 over bolt. Fasten assembly with lock nut.

Assemble FEED TUBE ASSEMBLY and HOPPER ASSEMBLY (FIGURES 12 and 13) with eight 3/8" x 1" carriage bolts and whiz nuts.


REF NO. PART# 1

2 3007

3 3352

3 3353

3 3354

4 3159

5

6 -7 3384

8 -9 3160

9 3161

9 3162

10

11 3381

12 3378

13 3379

14 3377

15 3382

16

17 3380

18 3355

18 3356

18 3357

19 3156

20 3138

21 3132

22 3134

23 3135

24 3131

25 1005

26 3176

27 3136

28 3137

29 1006

30 3133

31 3358


MAIN FRAME 6~ -~9

NO. USED DESCRIPTION 2 BOLT- 1/2" x 1-1/4" c/w LOCK WASHER

2 PLATED WASHER- 1/2" ID x 2-l/4" OD

1 MAIN FRAME ASSEMBLY (LEFT HAND)- SLMD12-2200



1 LOWER SUPPORT ASSEMBLY

24 UNC BOLT- 5/8" x 1-l/2" c/w LOCK WASHER AND NUT

2 HAIR PIN- 1/8" x 2-3/8"

2 DRAW PIN - 3/4" x 6"

2 UNC BOLT- 1" x 5" c/w LOCK NUT

1 AXLE ASSEMBLY- SLMD12-2200



1 NUT- 1"

1 THREADED ROD SWIVEL ASSEMBLY

1 TIE ROD BRACKET ASSEMBLY (LEFT HAND)

2 TIE ROD ASSEMBLY

1 TIE ROD BRACKET ASSEMBLY (RIGHT HAND)

1 THREADED ROD LOCK SWIVEL ASSEMBLY

4 UNC BOLT- 5/8" x 4" c/w LOCK WASHER AND NUT

1 THREADED ROD ASSEMBLY

1 MAIN FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2200



12 WHEEL BOLT- 1/2" x 1-1/4" UNF

2 RIM- 16"

2 DUST CAP

2 CASTLE NUT

2 TAPERED ROLLER BEARING CONE (OUTER)

2 HUB

2 TAPERED ROLLER BEARING CONE (INNER)

2 AXLE EXTENSION ASSEMBLY

2 SPINDLE WASHER

2 TAPERED ROLLER BEARING CUP (OUTER)

2 TAPERED ROLLER BEARING CUP (INNER)

2 GREASE SEAL

- HUB & SPINDLE- COMPLETE


A-FRAME

REF NO. PART# NO. USED DESCRIPTION 1 3251 1 BOTIOM LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2200

1 3299 1 BOTTOM LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2400

1 3252 1 BOTTOM LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2600

2 - 44 UNC BOLT- 5/8" x 1-1/2" c/w LOCK WASHER AND NUT

3 3169 1 BOTTOM LIFT FRAME CROSSBRACE ASSEMBLY

4 3365 1 BOTTOM LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD12-2200

4 3366 1 BOTIOM LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD12-2400

4 3367 1 BOTIOM LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD1 2-2600

5 2995 6 PLATED WASHER- 1-1/16" ID x 2-1/4" OD

6 - 2 UNC BOLT- 1" x 8" c(w LOCK NUT

7 3362 2 PIVOT BUSHING

8 3177 1 TOP LIFT FRAME ASSEMBLY (LEFT HAND)- SLMD12-2200



9 3259 1 BOTIOM CYLINDER MOUNT PIN

10 3257 1 HYDRAULIC CYLINDER

11 2996 1 NPT VENT

12 3260 1 TOP CYLINDER MOUNT PIN

13 2997 1 REDUCED ORIFICE FITIING

14 - 2 BOLT- 1" x 2-1/2" c/w LOCK NUT

15 2994 2 BUSHING

16 3383 1 TOP LIFT FRAME CROSSBRACE ASSEMBLY

17 3244 1 BOTIOM LIFT FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2200

17 3303 1 BOTTOM LIFT FRAME ASSEMBLY (RIGHT HAND) - SLM D12-2400

17 3363 1 BOTIOM LIFT FRAME ASSEMBLY (RIGHT HAND) - SLMD12-2600

18 3245 1 TOP LIFT FRAME ASSEMBLY (RIGHT HAND) - SLMD12-2200

18 3253 1 TOP LIFT FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2400

18 3254 1 TOP LIFT FRAME ASSEMBLY (RIGHT HAND)- SLMD12-2600

19 3167 1 TOP LIFT FRAME CRADLE ASSEMBLY- SLMD12-2200



20 3168 1 TOP LIFT FRAME CYLINDER MOUNT ASSEMBLY- SLMD12-2200



21 3385 SEAL KIT FOR HYDRAULIC CYLINDER

22 3153 4 LYNCH PIN


PTO SHAFT ASSEMBLY

REF NO. PART# NO. USED DESCRIPTION 1 3411 2 GUARD REPAIR KIT

2 3414 1 YOKE, TUBE AND SLIP SLEEVE

3 3413 1 INNER GUARD

4 3408 3 35R CROSS AND BEARING KIT

5 3415 1 BALL SHEAR ASSEMBLY

6 3406 2 SSUAUTO-LOK REPAIR KIT

7 3410 1 YOKE AND SHAFT

8 3409 1 CENTER HOUSING

9 3407 1 SAFETY SLIDE LOCK YOKE ASSEMBLY

10 3416 2 LOCK NUT

11 3417 2 3/8" X 1" GRADE 5 BOLT c/w NUT

12 3412 1 OUTER GUARD

13 3405 - JOINT AND TUBE HALF ASSEMBLY- INCLUDES REF #'S- 2,4,5

14 3404 JOINT AND TU BE HALF ASSEMBLY c/w INNER GUARD- INCLUDES REF #'S- 2,3,4,5

15 3401 - GUARD SET- INCLUDES REF #'S- 3,12

16 3403 JOINT AND SHAFT HALF ASSEMBLY- INCLUDES REF #'S- 4, 7, 8, 9

17 3402 - JOINT AND SHAFT HALF ASSEMBLY c/w OUTER GUARD- INCLUDES REF #'S- 4, 7, 8, 9, 12

3330 PTO SHAFT ASSEMBLY COMPLETE


HOPPER


HOPPER REF NO. PART# NO. USED DESCRIPTION

1 - 8 WHIZ BOLT- 1/4" x 3/4" c/w WHIZ NUT

2 3029 1 INSPECTION DOOR HANDLE

3 3227 1 INSPECTION DOOR

4 3228 1 INSPECTION DOOR HINGE

5 4 BOLT- 1/2" x 1-1/4" c/w WHIZ NUT

6 3059 4 PIVOT STOP

7 3225 1 HOPPER ASSEMBLY

8 3230 1 DRIVE SAHFT BUSHING HOLDER ASSEMBLY c/w BUSHING

9 1751 DRIVE SHAFT BUSHING (FOR USE WITH PART# 3230)

10 3048 2 LONG RUBBER BRACKET

11 3229 1 DR IVE SHAFT ASSEMBLY

12 3042 FLIGHT SHAFT BUSHING (FOR USE WITH PART# 3233)

13 6 WHIZ BOLT- 3/8" x 1 c/w WHIZ NUT

14 3233 2 FLIGHT SHAFT BUSHING HOLDER c/w BUSHING

15 3236 1 FLIGHT GUARD ASSEMBLY

16 3 CARRIAGE BOLT- 3/8" x 3/4" c/w WHIZ NUT

17 4 CARR IAGE BOLT- 3/8" x 1" c/w WING NUT

18 3237 1 FLIGHT GUARD MOUNTING BRACKET


20 3049 2 SHORT RUBBER BRACKET

21 3234 1 RIGHT HAND FLIGHT ASSEMBLY (LEFT HAND FLIGHT)

22 3058 1 INSPECTION DOOR CLOSURE WASHER

23 3057 1 INSPECTION DOOR CLOSURE SPRING

24 3056 1 INSPECTION DOOR CLOSURE

25 3226 1 PIVOT ASSEMBLY

26 1 BOLT- 3/8" x 1-1/2" c/w LOCK NUT

27 2 UNC BOLT- 5/8" x 1-3/4" c/w PLATE WASHER AND LOCK NUT

28 8 CARRIAGE BOLT- 3/8" x 1" c/w WHIZ NUT

29 3261 2 PIVOT SPACER

30 2 BOLT- 5/16" x 3/4" c/w WHIZ NUT

31 3232 1 RUBBER

32 3235 1 LEFT HAND FLIGHT ASSEMBLY (RIGHT HAND FLIGHT)

33 6 CARRIAGE BOLT- 3/8" x 1 c/w WHIZ NUT

34 1239 6 FLAGETIE

35 2316 2 FLIGHT BEARING

36 2777 1 DRIVE BEARING

37 3425 2 SEALING PLATE

38 3061 4 WHEEL SPACER

39 3239 4 WHEEL c/w TIRE

40 4 BOLT- 3/4" x 9" c/w PLATE WASHER AND LOCK NUT

41 3240 1 CHAIN

42 3241 1 CHAIN

43 3238 1 DRIVE GUARD

44 3053 1 BEARING- 1-1/4"

45 3397 2 DRIVE SPROCKET

46 3398 1 REVERSE SPROCKET

47 3396 1 DOUBLE DRIVE SPROCKET

48 2 WHIZ BOLT- 3/8" x 3/4" c/w WHIZ NUT

49 3392 2 CHAIN TENSION HOLDER PLATE

50 3391 2 CHAIN TENSION PLATE

51 2 CARRIAGE BOLT- 3/8" x 1-1/2" c/w LOCK NUT

52 2 DRAIN PLUG -CARRIAGE BOLT- 3/8" x 3/4" c/w WHIZ NUT

53 2 BOLT- 3/8" x 2-112" c/w LOCK NUT

54 3399 1 LEFT HAND FLIGHT EXTENSION ASSEMBLY (RIGHT HAND FLIGHT)

55 3400 1 RIGHT HAND FLIGHT EXTENSION ASSEMBLY (LEFT HAND FLIGHT)


FEED AUGER HEAD AND TUBE

REF NO. PART# NO. USED DESCRIPTION 1 - 16 WHIZ BOLT- 1/4" x 3/4" c/w WHIZ NUT

2 3220 1 RAIN GUARD (LEFT HAND)

3 3219 1 HEAD COVER ASSEMBLY

4 3221 1 RAIN GUARD (RIGHT HAND)

5 8 UNC BOLT- 3/8" x 1" c/w WHIZ NUT

6 3215 1 GEAR BOX ASSEMBLY COMPLETE

7 - 1 BOLT- 7/16" x 3" c/w LOCK NUT

8 3223 1 U-JOINT (FLIGHT TO GEAR BOX)

9 - 1 WOODRUFF KEY

10 3224 1 U-JOINT (GEAR BOX TO GEAR BOX)

11 3424 - U-JOINT CROSS KIT

12 - 8 CARRIAGE BOLT- 7116" x 1-1/4" c/w WHIZ NUT

13 3214 1 HEAD ASSEMBLY

14 3216 4 PIVOT SPACER PLATE

15 3217 4 PIVOT TOP PLATE

16 3212 1 FEED AUGER TUBE ASSEMBLY

17 3128 1 U-JOINT- 1-1/4" TO 1" SQUARE

18 3035 1 SQUARE STUB

19 3213 1 FEED AUGER FLIGHT ASSEMBLY

20 3029 2 HANDLE

21 3222 1 HEAD COVER HINGE

22 - 2 UNC BOLT- 5/8" x 1-1/2" c/w FLAT WASHER AND LOCK NUT

23 3034 2 BUSHING- 1" OD x .188" WALL DOM x 1/2" LONG x 5/8" ID

24 3218 1 RUBBER TUBING

25 3329 2 RUBBER TUBING CLAMP


LIFT ARM

REF NO. PART# NO. USED DESCRIPTION 1 - 2 UNC BOLT- 5/8" x 2-1/2" c/w NUT AND LOCK WASHER 2 3148 1 LIFT ARM PIVOT ASSEMBLY

3 3147 2 LIFT ARM PIVOT ROLLER BEARING 4 - 2 BOLT - 1/2" x 3-1/2" c/w LOCKNUT 5 3181 1 LIFT ARM PIVOT BASE ASSEMBLY 6 3151 1 LIFT ARM PIVOT COLLAR 7 3149 2 BUSHING 8 1782 3 CABLE ROLLER ASSEMBLY 9 - 4 HEAVY 1-1/8" x 18 GAUGE MACHINERY BUSHING 10 2 CODER PIN- 1/8" x 3/4" 11 3178 1 LIFT ARM TUBE ASSEMBLY 12 1 HAIR PIN 13 3189 1 LIFT ARM SADDLE ROLLER COVER 14 1 LIGHT - 1-1/8" x 18 GAUGE MACHINERY BUSHING 15 3145 1 LIFT ARM SAFETY CHAIN LUG 16 1 CABLE CLAMP- l/4" 17 1 CARRIAGE BOLT- 3/8" x 1" c/w WHIZ NUT 18 2700 1 LIFT HOOK 19 3182 1 HOPPER LIFT CABLE 20 3154 1 SAFETY HOOK c/w PIN AND CODER PIN 21 3155 1 SAFETY CHAIN 22 1387 1 LIFT ARM CABLE PIN 23 2699 1 DRAW PIN 24 3153 1 LYNCH PIN


TOP GEAR BOX

REF NO. PART# NO. USED DESCRIPTION 1 3282 1 QUILL SEAL

2 3265 1 QUILL

3 3287 3 0-RING

4 3274 AS REQ'D GASKET

5 3269 4 SNAP RING

6 3268 3 SPACER

7 3267 4 BEARING CONE

8 3258 4 BEARING CUP

9 3278 1 QUILL SHAFT

10 3284 2 SQUARE KEY

11 3272 2 GEAR

12 3283 1 CROSS SEAL

13 3266 1 CROSS END CAP

14 3280 1 CROSS SHAFT

15 3264 1 HOUSING

16 3277 2 PIPE PLUG

17 3270 1 END CAP

18 3249 12 CAPSCREW

- 3215 - GEAR BOX ASSEMBLY COMPLETE (FEED AUGER HEAD END ASSEMBLY GEAR BOX)


REF NO. PART# NO. USED DESCRIPTION I 3286 I SHIELD

2 3282 I QUILL SEAL

3 3271 I QUILL

4 3273 I GREASE ZERK

5 3287 3 0-RING

6 3274 AS REQ'D GASKET

7 3269 4 SNAP RING

8 3268 3 SPACER

9 3267 4 BEARING CONE

10 3258 4 BEARING CUP

11 3285 1 GREASE WASHER

12 3279 I QU ILL SHAFT

13 3284 2 SQUARE KEY

14 3272 2 GEAR

15 3283 I CROSS SEAL

16 3266 I CROSS END CAP

17 3281 I CROSS SHAFT

18 3264 I HOUSING

19 3277 2 PIPE PLUG

20 3270 1 END CAP

21 3249 12 CAPSCREW

3262 GEAR BOX ASSEMBLY COMPLETE (BOOT ASSEMBLY GEAR BOX)

AL SLMD OPERATORS MANU

BOOT

36 ~ '2V


BOOT REF NO. PART# NO. USED DESCRIPTION

I 2711 I REVERSE SHAFT

2 3262 I GEAR BOX ASSEMBLY (COMPLETE)

3 - 4 UNC BOLT- 1/2" x 1-3/4" C/w LOCK WASHER AND NUT

4 3116 BRONZE BUSHING (FOR USE WITH PART# 3202)

5 3202 1 GEAR BOX BUSHING HOUSING ASSEMBLY C/w BUSHING

6 - 8 CARRIAGE BOLT- 7/16" x 1-1/4" C/w WHIZ NUT

7 3246 4 PIVOT TOP PLATE

8 3247 4 PIVOT SPACER PLATE

9 3243 1 PIVOT RING ASSEMBLY

10 3200 I BOOT ASSEMBLY

II 6 UNC BOLT- GRADE 2 - 3/8" x I" C/w LOCK NUT


13 2877 2 FELT WASHER

14 2827 3 BEARING INSERT C/w HOUSING (GEAR BOX CROSS SHAFT, REVERSE SHAFT INSIDE & OUTSIDE BOOT)

15 2715 3 SPROCKET (GEAR BOX CROSS SHAFT, REVERSE SHAFT & FLIGHT SHAFT)

16 I SQUARE KEY- 5/16" x 1-1/4"

17 3211 I DRIVE CHAIN

18 3206 1 DRIVE GUARD ASSEMBLY

19 3263 1 DRIVE GUARD HINGE

20 8 CARRIAGE BOLT- 1/4" x 3/4" C/w WHIZ NUT

21 4 UNC BOLT- l/2" x 2-l/4" C/w LOCK NUT AND WASHER

22 2714 1 REVERSE BEARING SH IELD

23 4 BOLT - 5/8" x 2" C/w LOCK WASHER AND NUT

24 3203 I FLIGHT BUSHING HOUSING ASSEMBLY c/w BUSHING

25 I CARRIAGE BOLT- 1/4" x 3/4" c/w WING NUT

26 30 14 I INSPECTION DOOR

27 1 CARRIAGE BOLT- 1/4" x 3/4" C/w LOCK NUT

28 1 UNC BOLT- 3/8" x 3/4" C/w WHIZ NUT

29 4 CARRIAGE BOLT- 3/8" x 3/4" C/w WHIZ NUT

30 2708 2 CLEAN OUT DOOR LATCHES

3 1 3205 1 MAIN HITCH ASSEMBLY

32 3164 I MAIN HITCH CONNECTOR PLATE

33 - 2 WOODRUFF KEY l/4" x I"

34 3209 I BEARING INSERT c/w HOUSING (FLIGHT SHAFT)

35 2 CARRIAGE BOLT- 3/8" x 3/4" c/w WING NUT

36 2 SPRING PIN

37 2699 I DRAW PIN

38 3201 I CLEAN OUT DOOR ASSEMBLY

39 2725 I JACK C/w DRAW PIN & SPRING PIN

40 3020 I U-BOLT c/w LOCK WASHERS AND NUTS

41 2 BOLT- l/2" x 1-l/2" C/w LOCK WASHER AND NUT

42 2723 I HITCH INSERT ASSEMBLY

43 - 4 WHIZ BOLT- 1/4" x 5/8" c/w WHIZ NUT

44 4 UNC BOLT- 3/8" x I" C/w WHIZ NUT

45 3370 1 PTO GUARD

46 2620 I PIN - 3/8" x 4"

47 I UNC BOLT- 3/8" x 4-1/2" C/w LOCK NUT

48 2883 I PTO BRACKET - LEFT

49 2882 1 PTO HOLDER ASSEMBLY

50 2884 1 PTO BRACKET- RIGHT

51 3042 - BRONZE BUSHING (FOR USE WITH PART# 3203)

52 1578 - BEARING INSERT C/w COLLAR (FOR USE WITH PART# 2827)

53 3207 - BEARING INSERT C/w COLLAR (FOR USE WITH PART# 3209)


TUBE ASSEMBLY - 2200

1~ ~ . .,. .. ..... :


TUBE ASSEMBLY - 2200 REF NO. PART# NO. USED DESCRIPTION

1 - 4 BOLT- 5/8" x 1-3/4" c/w LOCK WASHER AND NUT

2 3199 1 HEAD END PLATE

3 3209 1 BALL BEARING INSERT c/w HOUSING

4 1 BOLT- 1!2" x 1-1/4" c/w LOCK WASHER

5 3196 1 TOP FLIGHT ASSEMBLY- SLMD12-2200

6 3193 1 TOP TUBE ASSEMBLY- SLMD12-2200

7 12 WHIZ BOLT- 1/2" x 1" c/w WH IZ NUT

8 3371 1 HYDRAULIC HOSE AT FLANGE

9 3300 1 PLATED HYDRAULIC LINE- SLMD12-2400

10 2 UNC BOLT- 5/8" x 2" c/w 5/8" WASHER, LOCK WASHER AND NUT

11 3070 2 CABLE BUSHING

12 3372 1 HYDRAULIC HOSE AT CYLINDER- SLMD12-2200

13 - 8 WHIZ BOLT- 5/16" x 1" c/w WHIZ NUT

14 3248 1 ANGLE SPOUT ASSEMBLY

15 3175 1 BOTIOM FLIGHT ASSEMBLY

16 3172 1 BOTIOM TUBE ASSEMBLY- SLMD12-2400

17 - 33 WHIZ BOLT- 1/2" x 1-1/4" c/w WH IZ NUT

18 - 3 WHIZ BOLT- 1!2" x 1-3/4" c/w WH IZ NUT (3 BOTIOM BOLTS AT BOOT FLANGE ONLY)

19 3095 13 HYDRAU LIC LI NE CLIP- SLMD12-2200

20 13 SELF THREADING SCREW- 1/4"- SLMD12-2200

21 3096 1 HYDRAU LIC LINE SPLICE CONNECTOR

22 3188 1 PLATED HYDRAULIC LINE- LONG

23 1725 1 NEEDLE VALVE

24 3093 2 HYDRAULIC HOSE CONNECTOR

25 3187 1 PLATED HYDRAU LI C LINE- SHORT

26 3113 1 MALE PIONEER TIP

27 3088 1 HYDRAULIC HOSE c/w ENDS

28 3207 BEARING INSERT c/w COLLAR (FOR USE WITH PART# 3209)


TUBE ASSEMBLY- 2400 & 2600

2


TUBE ASSEMBLY - 2400 & 2600 REF NO. PART# NO. USED DESCRIPTION





3 12 WHIZ BOLT- 1/2" x 1" c/w WHIZ NUT

4 3199 1 HEAD END PLATE

5 3209 1 BALL BEARING INSERT c/w HOUSING

6 - 1 BOLT- 1/2" x 1-1/4" c/w LOCK WASHER

7 3170 1 MIDDLE FLIGHT ASSEMBLY

8 3248 1 ANGLE SPOUT ASSEMBLY

9 - 8 WHIZ BOLT- 5/16" x 1" c/w WHIZ NUT

10 3297 1 MIDDLE TUBE ASSEMBLY- SLMD12-2400

10 3298 1 MIDDLE TUBE ASSEMBLY- SLMD12-2600

11 - 4 BOLT- 5/8" x 1-3/4" c/w LOCK WASHER AND NUT

12 - 49 WHIZ BOLT- 1/2" x 1-1/4" c/w WHIZ NUT

13 3371 1 HYDRAULIC HOSE AT FLANGE



15 2 UNC BOLT- 5/8" x 2" c/w 5/8" WASHER, LOCK WASHER AND NUT

16 3()7'(;- 2 CABLE BUSHING



18 3175 1 BOTIOM FLIGHT ASSEMBLY



20 3 WHIZ BOLT- 1/2" x 1-3/4" c/w WHIZ NUT (3 BOTIOM BOLTS AT BOOT FLANGE ONLY)

21 3095 13 HYDRAULIC LINE CLIP- SLMD12-2400

21 3095 14 HYDRAULIC LINE CUP- SLMD12-2600

22 - 13 SELF THREADING SCREW- 1/4"- SLMD12-2400

22 - 14 SELF THREADING SCREW- 1/4"- SLMD12-2600

23 3096 1 HYDRAULIC LINE SPLICE CONNECTOR

24 3188 1 PLATED HYDRAULIC LINE- LONG

25 1725 1 NEEDLE VALVE

26 3093 2 HYDRAULIC HOSE CONNECTOR

27 3187 1 PLATED HYDRAULIC LINE- SHORT

28 3113 1 MALE PIONEER TIP

29 3088 1 HYDRAULIC HOSE c/w ENDS

30 3207 - BEARING INSERT c/w COLLAR (FOR USE WITH PART# 3209)


TRUSS ASSEMBLY

BOOT-END

MAIN FRAME ASSEMBLY MOUNTING PLATE A-FRAME ASSEMBLY MOUNTING PLATE

SLMD12 TRUSS ASSEMBLIES KEY PLAN

FIGURE Kl FIGURE K2

FIGURE K4

FIGURE K3 ~ FIGURE KS


TRUSS ASSEMBLY REF NO. PART# NO. USED DESCRIPTION

1 3087 4 EYE BOLT c/w TWO NUTS

2 3313 1 LONG TRUSS CABLE- SLMD12-2200



3 8 CABLE CLAMP - 5/ 16"

4 20 UNC BOLT- 7/16" x 1-1/4" c/w WHIZ NUT

5 3180 2 SMALL TRUSS BRACE

6 3068 4 SMALL TRUSS RISER

7 - 8 CABLE CLAMP- 3/8"

8 3314 1 SHORT TRUSS CABLE- SLMD12-2200



9 3079 2 LARGE TRUSS RISER

10 3078 2 LARGE TRUSS BRACE

11 - 1 BOLT- 7/16" x 3" c/w WHIZ NUT

12 3179 1 LARGE TRUSS SPACER

13 3070 4 CABLE BRACKET BUSHING

14 4 UNC BOLT- 5/8" x c/w WASHER, LOCK WASHER AND NUT


FULTON K1550 BRAKE WINCH

REF NO. PART# NO. USED DESCRIPTION 1 - 1 FRAME SPACER

2 1 LOCK NUT- 3/8"

3 1936 1 INPUT SHAFT

4 1 FRAME

5 - 3 LOCK NUT- l/2"

6 1672 1 CABLE CLAMP

7 1673 1 DRUM ASSEMBLY

8 1 KEEPER

9 - 1 UNC BOLT- 1/2" x 5-3/4"

10 1937 2 BUSHING

11 1947 1 PINION AND DISK

12 1677 2 BRAKE PAD

13 1932 1 RATCHET GEAR

14 1933 1 SHAFT BRAKE DISK

15 1712 1 PAWL AND SPRING KIT

16 1 UNC BOLT- 3/8' x 5-3/4"

17 1934 1 SPACER

18 1711 1 HANDLE

19 - 1 NYLON LOCK NUT- 1/2"

- 1671 FULTON K1550 BRAKE WINCH ASSEMBLY- COMPLETE


BOLT ON WINCH PLATE

REF NO. PART# NO. USED DESCRIPTION 1 2717 1 WINCH HANDLE ASSEMBLY

2 - 1 HAIR PIN

3 1175 1 WINCH CHAIN

4 - 1 BOLT- 1/2" x 8" C/w LOCK NUT

5 3126 1 WINCH DRIVE SHAFT ASSEMBLY

6 2713 2 WINCH DRIVE SHAFT BEARING (COMPLETE)

7 7 CARR IAGE BOLT- 3/8" x 3/4" C/w WHIZ NUT

8 2718 WINCH DRIVE SHAFT BEARING (INSERT ONLY)

9 3103 1 SPROCKET

10 1671 1 WINCH ASSEMBLY

11 3125 1 BOLT ON WINCH PLATE

12 - 1 BOLT- 1/2" x 9" C/w LOCK NUT


REF. PART# PAGE REF. PART# PAGE REF. PART# PAGE REF. PART# PAGE

25 1005 23 21 3096 35 16 3212 28 17 3281 31 29 1006 23 23 3096 37 19 3213 28 1 3282 30 3 1175 41 9 3103 41 13 3214 28 2 3282 31

34 1239 27 26 3113 35 6 3215 28 12 3283 30 22 1387 29 28 3113 37 3215 30 15 3283 31 52 1578 33 4 3116 33 14 3216 28 10 3284 30

1671 40 11 3125 41 15 3217 28 13 3284 31 10 1671 41 5 3126 41 24 3218 28 11 3285 31 6 1672 40 17 3128 28 3 3219 28 1 3286 31 7 1673 40 24 3131 23 2 3220 28 3 3287 30 12 1677 40 21 3132 23 4 3221 28 5 3287 31 18 1711 40 30 3133 23 21 3222 28 10 3297 37 15 1712 40 22 3134 23 8 3223 28 10 3298 37 23 1725 35 23 3135 23 10 3224 28 1 3299 24 25 1725 37 27 3136 23 7 3225 27 9 3300 35 9 1751 27 28 3137 23 25 3226 27 14 3301 37 8 1782 29 20 3138 23 3 3227 27 14 3302 37 13 1932 40 15 3145 29 4 3228 27 17 3303 24 14 1933 40 3 3147 29 11 3229 27 2 3313 39 17 1934 40 2 3148 29 8 3230 27 8 3314 39 3 1936 40 7 3149 29 31 3232 27 25 3329 28 10 1937 40 6 3151 29 14 3233 27 3330 25 11 1947 40 22 3153 24 21 3234 27 3 3352 23 35 2316 27 24 3153 29 32 3235 27 3 3353 23 46 2620 33 20 3154 29 15 3236 27 3 3354 23 23 2699 29 21 3155 29 18 3237 27 18 3355 23 37 2699 33 19 3156 23 43 3238 27 18 3356 23 18 2700 29 4 3159 23 39 3239 27 18 3357 23 30 2708 33 9 3160 23 41 3240 27 31 3358 23 1 2711 33 9 3161 23 42 3241 27 7 3362 24 6 2713 41 9 3162 23 9 3243 33 17 3363 24 22 2714 33 32 3164 33 17 3244 24 4 3365 24 15 2715 33 19 3167 24 18 3245 24 4 3366 24 I 2717 41 20 3168 24 7 3246 33 4 3367 24 8 2718 41 3 3169 24 8 3247 33 20 3368 24 42 2723 33 7 3170 37 14 3248 35 20 3369 24 39 2725 33 16 3172 35 8 3248 37 45 3370 33 36 2777 27 19 3173 37 18 3249 30 8 3371 35 14 2827 33 19 3174 37 21 3249 31 13 3371 37 13 2877 33 15 3175 35 1 3251 24 12 3372 35 49 2882 33 18 3175 37 1 3252 24 17 3373 37 48 2883 33 26 3176 23 18 3253 24 17 3374 37 50 2884 33 8 3177 24 18 3254 24 19 3375 24 15 2994 24 11 3178 29 8 3255 24 19 3376 24 5 2995 24 12 3179 39 8 3256 24 14 3377 23 II 2996 24 5 3180 39 10 3257 24 12 3378 23 13 2997 24 5 3181 29 8 3258 30 13 3379 23 2 3007 23 19 3182 29 10 3258 31 17 3380 23

26 3014 33 8 3183 39 9 3259 24 11 3381 23 40 3020 33 8 3184 39 12 3260 24 15 3382 23 2 3029 27 2 3185 39 29 3261 27 16 3383 24 20 3029 28 2 3186 39 3262 31 7 3384 23 23 3034 28 25 3187 35 2 3262 33 21 3385 24 18 3035 28 27 3187 37 19 3263 33 50 3391 27 12 3042 27 22 3188 35 15 3264 30 49 3392 27 51 3042 33 24 3188 37 18 3264 31 47 3396 27 10 3048 27 13 3189 29 2 3265 30 45 3397 27

20 3049 27 6 3193 35 13 3266 30 46 3398 27 44 3053 27 2 3194 37 16 3266 31 54 3399 27 24 3056 27 2 3195 37 7 3267 30 55 3400 27 23 3057 27 5 3196 35 9 3267 31 15 3401 25 22 3058 27 1 3197 37 6 3268 30 17 3402 25 6 3059 27 1 3198 37 8 3268 31 16 3403 25

38 3061 27 2 3199 35 5 3269 30 14 3404 25 6 3068 39 4 3199 37 7 3269 31 13 3405 25 II 3070 35 10 3200 33 17 3270 30 6 3406 25 16 3070 37 38 3201 33 20 3270 31 9 3407 25 13 3070 39 5 3202 33 3 3271 31 4 3408 25 10 3078 39 24 3203 33 11 3272 30 8 3409 25 9 3079 39 31 3205 33 14 3272 31 7 3410 25 1 3087 39 18 3206 33 4 3273 31 1 3411 25

27 3088 35 53 3207 33 4 3274 30 12 3412 25 29 3088 37 28 3207 35 6 3274 31 3 3413 25 24 3093 35 30 3207 37 16 3277 30 2 3414 25 26 3093 37 34 3209 33 19 3277 31 5 3415 25 19 3095 35 3 3209 35 9 3278 30 10 3416 25 21 3095 37 5 3209 37 12 3279 31 11 3417 25 21 3095 37 17 3211 33 14 3280 30 11 3424 28

37 3425 27


Limited Warranty Statement

Sakundiak Equipment Ltd. warrants each new Sakundiak Equipment Ltd. product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed twelve (12) consecutive months, or forty-five (45) days in the case of commercial use, from the date of delivery of the new Sakundiak Equipment Ltd . product to the original purchaser.

Genuine Sakundiak Equipment Ltd. replacement parts and components will be warranted for thirty (30) days from the date of purchase, or the remainder of the original equipment warranty period, whichever is longer. Under no circumstances will Sakundiak Equipment Ltd. cover any merchandise or components thereof, which, in the opinion of Sakundiak Equipment Ltd., has been subjected to misuse, unauthorized modifications, alteration, an accident or if repairs have been made with parts other than those obtainable through Sakundiak Equipment Ltd.

Sakundiak Equipment Ltd. in no way warrants engines, batteries, tires, or other trade accessories since these items are warranted separately by their respective manufacturer. Our obligation under this warranty shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our judgement, shall show evidence of such defect, provided further that such a part shall be returned within thirty (30) days from date of failure to Sakundiak Equipment Ltd., routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid.

This warranty shall not be interpreted to render Sakundiak Equipment Ltd. liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. Except as set forth above, Sakundiak Equipment Ltd. shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages.

Sakundiak Equipment Ltd. makes no other warranty, expressed or implied, and, specifically, Sakundiak Equipment Ltd. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties, so the limitations or exclusions in this warranty may not apply.

This warranty is subject to any existing conditions of supply which may directly affect our ability to obtain materials or manufacture replacement parts. Sakundiak Equipment Ltd. reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservation.

assembly instructions operator's manual parts listshortlineag.com/slmd12 manual.pdf · 2011....

Documents