q series wg2 and 3 button call points - hills industries ltd · 2014-10-03 · wg2 and 3 button...
Post on 20-Jun-2020
0 Views
Preview:
TRANSCRIPT
Q SeriesWG2 and 3 buttoncall points
hills.com.au
The Q-Series WG2 and WG3 wireless Call Points are wall-mounted single-gang plates with one or two call-function and Cancel tactile buttons and a dual-colour reassurance LED. Multiple button options are available including Call, Assist, Emergency, Presence, etc. (see ordering information for further detail).
The ultra-low power Wi-Fi call point is typically located at the bed and connects to industry-standard 802.11b/g wireless access points, eliminating the need for extensive cabling infrastructure. The buttons are used to initiate and cancel alarms.
When a call button is pushed the LED will flash and an audible beep will sound to provide reassurance that the call has been received by the system. Alarms may be displayed visibly and audibly on other peripheral nurse call system devices to alert staff.
The points are designed for health care environments that demand secure and reliable communication protocols with guaranteed message delivery. Requires QSWCA-N01 Wi-Fi CareView Adaptor 1.0 and CVNC CareView 1.5 or greater software.
Operation
Available in a variety of two and three buttons – Call, Assist, Emergency, Presence, Duress, Call & Assist, and Cancel
Built-in audible and visual (green/ red/LED) reassurance indicators
Ultra-low power battery operation
Easy battery replacement
Fully monitored bi-directional communications over TCP/IP, HTTP+JSON
Static and dynamic IP addressing
When Button 1 or Button 2 is pressed the button is latched on and a message is sent to the server
When the Cancel “C” button is pressed, Button 1 and/or Button 2 is cleared and a massage is sent to the server
Call point provides audible and visual (green/red LED) reassurance on success/failure conditions
Call point will retransmit messages at predefined intervals until acknowledged at the server
Call point sends health and status messages at periodic intervals (e.g. every 15 minutes)
Supports 64/128-bit WEP, WPA2-PSK authentication with AES encryption
Over the air (OTA) firmware and configuration upgrades
Easy to clean & maintain
Easy installation & relocation
Water resistant (IP67 rated)
Braille for “CALL” buttons
High polish polycarbonate plastic with antimicrobial additive
Adheres to Australian Standard AS3811–1998 where applicable
Key features
hills.com.au
Productspecifications
Dimensions
Mounting
Battery
Operation Voltage Range
Battery Life
Current (Sleep)
Current (Operating)
Current (Communications)
International Protection Rating
Operating Temperature Range
Environmental
Interface
Security
Protocols
Wi-Fi Output Power
Wi-Fi Receiver Sensitivity
802.11b/g Channels
Battery Measurement
Temperature Measurement
Functions
Communications
Power
Physical Characteristics 74.5mm x 115.5mm x 28.75mm + 3mm wall mounting plate
Call Point is attached to an Australian standard sized wall plateHole spacing 84mm and 100mm
3 volts Lithium CR123 or CR123A
2.5 to 3.2 volts
3+ years (15 minute Check-In Interval)
4 to 6µA
40 to 50mA
200mA
IP67 (Dust tight, liquid immersion to 1m)
0°C to 40°CBattery life is reduced on both low and high ends of the temperature range
2.4Ghz IEEE 802.11b/g Wi-Fi Certified WPA2 Enterprise, WMM QoS and WMM Power Save
WEP-40, WEP-104, WPA-PSK, WPA2-PSK
TCP/IPTFTPHTTP 1.1/JSONDHCP or Static IP Layer 3 Addressing
14dBm
-72dBm 54Mbits/s 10% PER-86dBm 11Mbits/s 10% PER
1,6,11
Key:BattValues: 2000–3700Units: mV
Key: TempValues: 0–40 (on chip temperature)Unit/Precision: Degrees Celsius +/- 1%?
hills.com.au
Productspecifications
Functions Button 1
Button 2
Key: Button1Values: 0 = Reset, 1 = Latched
Key: Button2Values: 0 = Reset, 1 = Latched
Battery LifePerformance Check-In Interval (minutes)3715 (recommended)
Est. Battery Life (years)1+2+3+
Communication Security
NoneWEPWPA2
Operation
Button1/Button2 is pressed
Cancel button is pressed
Hello request
Sounder
Chirps once and then chirps once every 10 seconds (success) OR Off (failure)
Off
Chirps once (success)
LED indicator
Illuminates green for 1 second and then flashes green once every 2 seconds (success) OR flashes red once every 2 seconds (failure)
Off (success) OR flashes red once every 2 seconds (failure)
Off
Audible and Visual Reassurance
hills.com.au
Productdimensions
Front Side
Battery replacement
Installation
28.75mm
74.50
115.
50
74.50mm
115.
50m
m
REMOVE FRONT COVER TO ACCESS SEALED BATTERY COMPARTMENT
INSERT BATTERY IN THE CORRECT ORIENTATION AS SHOWN
hills.com.au
Ordering information
Item Item No.
802.11b/g Wi-Fi Call Point
802.11b/g Wi-Fi Emergency Point
802.11b/g Wi-Fi Presence Point
802.11b/g Wi-Fi Assist Point
802.11b/g Wi-Fi Duress Point
802.11b/g Wi-Fi Call and Assist Point
QCA021-WG
QCA022-WG
QCA023-WG
QCA024-WG
QCA026-WG
QCA032-WG
Replacement 3V 1400mAh Lithium Battery
CR123A
hills.com.au
Australian standard sized vertical mounting plate with adhesive contact
QCA-MP
Australian standard sized vertical blank plate
QCA-BP
top related