class f3p indoor aerobatic power model aircrafts

Class F3P Indoor Aerobatic Power Model

aircrafts

Schedule F3P – AP-15

Security line

Take-off procedure( not judged, not scored )

¼ rollroll

F3P-AP-15.01: Square Reverse Cuban Eight with roll up, two consecutive 1/4 rolls up

F3P-AP-15.01.01

¼ roll

All radii are equal.

Roll on middle of the line.

F3P-AP-15.01.02

¼ rollroll

¼ roll

F3P-AP-15.01: Square Reverse Cuban Eight with roll up, two consecutive 1/4 rolls up

¼ rolls centered on middle of the line.

45°45°

F3P-AP-15.02.01

F3P-AP-15.02: Knife-Edge Trombone with 1/4 roll up, 1/4 roll down

pushed half circle

1/4 roll

1/4 roll

F3P-AP-15.02.01

F3P-AP-15.02: Knife-Edge Trombone with 1/4 roll up, 1/4 roll down

The radii of the 1/8 loops are equal.

¼ rolls on middle of the line

1/4 roll

1/4 roll

wing 45°

1/4 roll45°

F3P-AP-15.03.01

F3P-AP 13.03: Loop with two rolls in opposite direction integrated

F3P-AP-15.03.02

F3P-AP 13.03: Loop with two rolls in opposite direction integrated

Rolls must be in opposite directions.

Rolls must be integrated on circular flight path of the loop.

Loop must be round.

Roll reversal is immediate

F3P-AP 13.04: Camel Humpty-Bump with 1/4 roll up, 1/4 roll down

F3P-AP-15.04.01

1/4 roll

1/4 roll

F3P-AP 13.04: Camel Humpty-Bump with 1/4 roll up, 1/4 roll down

F3P-AP-15.04.02

1/4 roll

1/4 roll

All radii are equal.

¼ rolls on middle of the lines.1/4 roll

F3P-AP-15.05.01

F3P-AP-15.05: Eight Consecutive 1/8 rolls

eight 1/8 rolls

The 1/8 rolls must have the same roll rate.

Lines between part rolls must be short and of equal length.

F3P-AP-15.06.01

F3P-AP-15.06: Stall Turn with two consecutive 1/2 rolls in opposite directions up, 1/2 roll down

½ roll½ roll

Stop before pivot

Pivot on CG

Two wing spans or more – zero points!

½ rolls centered on middle of the line.

Between part rolls in opposite direction there must be no line.

F3P-AP-15.06.02

F3P-AP-15.06: Stall Turn with two consecutive 1/2 rolls in opposite directions up, 1/2 roll down

½ roll

Pivot on CG

½ roll on middle of the line.

F3P-AP-15.07: Knife Edge Top Hat with 3/4 roll up, 1/4 roll down

F3P-AP-15.07.01

¾ roll¼ roll

½ roll

F3P-AP-15.07: Knife Edge Top Hat with 3/4 roll up, 1/4 roll down

F3P-AP-15.07.02

All radii are equal.

¾ roll¼ roll

½ roll

¾ roll, ½ roll, ¼ roll on middle of the lines.

During the knife edge the wing must be in the vertical plane.

F3P-AP-15.08: Half Cuban Eight with roll down

F3P-AP-15.08.01

roll

F3P-AP-15.08: Half Cuban Eight with roll down

F3P-AP-15.08.02

roll

F3P-AP-15.08: Half Cuban Eight with roll down

F3P-AP-15.08.01

Roll on middle of the line.

All radii are equal.45°

F3P-AP-15.09.01

F3P-AP-15.09: Horizontal Circle with two consecutive rolls integrated

F3P-AP-15.09.02

F3P-AP-15.09: Horizontal Circle with two consecutive rolls integrated

All rolls are integrated on circular flightpath.

Circle must be of constant radius.

Roll rates must be constant.

Rolls must be inside.

F3P-AP-15.10.01

F3P-AP-15.10: Half Horizontal Knife Edge Circle with 1/4 roll, 1/2 roll integrated, 1/4 roll

1/4 roll

½ rollintegrated

1/4 roll

F3P-AP-15.10.02

F3P-AP-15.10: Half Horizontal Knife Edge Circle with 1/4 roll, 1/2 roll integrated, 1/4 roll

1/4 roll

½ rollintegrated

1/4 roll

Half Circle must be of constant radius.

1/2 roll is integrated on circular flightpathof the 90° segment of the 1/2 circle.

During the knife edge the wing must be in the vertical plane.

F3P-AP-15.10.03

F3P-AP-15.10: Half Horizontal Knife Edge Circle with 1/4 roll, 1/2 roll integrated, 1/4 roll

1/4 roll

½ rollintegrated

1/4 roll

Option

F3P-AP-15.11.01

F3P-AP-15.11: Vertical upline with consecutive four 1/8 Torque Rolls

1/8 torque roll

1/8 torque roll

1/8 torque roll

1/8 torque roll

F3P-AP-15.11.01

F3P-AP-15.11: Vertical upline with consecutive four 1/8 Torque Rolls

1/8 torque roll

1/8 torque roll

1/8 torque roll

1/8 torque roll

Peter Uhlig,November 2013

Landing sequence( not judged, not scored )

security line