xls1000 system description (4) (1)
TRANSCRIPT
-
8/19/2019 XLS1000 System Description (4) (1)
1/30
® U.S. Registered Trademark
Copyright © 1996 Honeywell Inc. • All Rights Reserved 74-245
10-96
XLS1000
SYSTEM DESCRIPTION
Life Safety
-
8/19/2019 XLS1000 System Description (4) (1)
2/30
Copyright © 1996 Honeywell Inc. • All Rights Reserved
-
8/19/2019 XLS1000 System Description (4) (1)
3/30
XLS1000 SYSTEM DESCRIPTION
i 74-245
Contents
Overview ............................................................................................................................ 1
XLS1000 Hardware ............................................................................................................................ 3
Panel Assembly .................................................................................................. 3Local Rail Modules ............................................................................................. 4Power Supplies................................................................................................... 11Enclosures .......................................................................................................... 14
System Operation ............................................................................................................................ 15System Power Up............................................................................................... 19System Supervisor ............................................................................................. 20Fire Alarm Operations......................................................................................... 20Supervisory Operations ...................................................................................... 20Monitor Operations ............................................................................................. 20Optional Operations............................................................................................ 20
System Definition Utility ............................................................................................................................ 22System Architecture Configuration and Sizing ................................................... 23
-
8/19/2019 XLS1000 System Description (4) (1)
4/30
XLS1000 SYSTEM DESCRIPTION
74-2450 ii
-
8/19/2019 XLS1000 System Description (4) (1)
5/30
XLS1000 SYSTEM DESCRIPTION
1 74-245
Overview
Worldwide Market Applications The XLS1000 Life Safety System (XLS1000) is a highly adaptable life safetysystem that can be applied to worldwide market applications. These applicationscan range from medium to large buildings; and over campus style layouts with manytypes of structures.
The XLS1000 is a modular system designed for fast assembly at the job site or in afactory environment. A powerful programming tool helps define flexible systemoperations in a fraction of the time required by others. These features help satisfycustomer needs at a lower installed cost.
System size is scalable from one node with a few points up to 64 nodes and 80,000points with peer to peer communications.
Single Panel Stand AloneLife Safety System As a single node, standalone system a panel may grow from five to 21 module
spaces.
A Single Panel Stand Alone Life Safety Systems consists of:• Central Processing Unit (CPU) to control serial bus communications to Local Ra
Modules (LRMs)
• The CPU supports the addition of an LCD Operator Interface (OI)• Local Rail Modules (LRMs) interface building wiring to the system• LRMs support the addition of Control Display Modules (CDMs)• CDMs provide traditional LED zone annunciation and switch controls• A panel provides physical space for a CPU and up to 19 single space LRMs (the
CPU uses two module spaces)
Central Processing
Unit (CPU)
Local Rail
Module(LRM)
Control Display Module
(CDM)
LCD
Operator
Interface
Up to 19 LRMs Total
LocalRail
Local Rail
Module
(LRM)
Fig. 1. Single Panel Stand Alone System Architecture.
The capacity of a single panel depends on the various types of LRMs needed orconfigured at a particular location.
Multiple Node Network In a multiple node network:• Each node has a CPU with a Network Communication Card with two RS-485
serial ports.
-
8/19/2019 XLS1000 System Description (4) (1)
6/30
XLS1000 SYSTEM DESCRIPTION
74-2450 2
• The Network Communication Card mounts to the back of the CPU.• Remote network nodes need not have a LCD or Control Display Modules.• The physical capacity of a single network depends on the various types of nodes
(maximum 64 Nodes) and LRMs needed to configure a system.
As a single network with multiple panels, the network can have up to 64 nodes.
Local RailModule(LRM)
Ctrl DisplayModule(CDM)
Up to 64NodesTotal
LCDOperatorInterface
Local Rail
Module(LRM)
Local RailModule(LRM)
Local RailModule(LRM)
Local Rail
Module(LRM)
Local RailModule(LRM)
Local Rail
Module(LRM)
Local RailModule(LRM)
Local RailModule(LRM)
Ctrl Display
Module(CDM)
Ctrl Display
Module(CDM)
Up to 19 LRMs Up to 19 LRMs Up to 19 LRMs
Local Rail Local Rail Local Rail
Central ProcessingUnit (CPU
Central ProcessingUnit (CPU
Central ProcessingUnit (CPU
Fig. 2. Multiple Node Network System Architecture.
Peer-to-Peer Communications The XLS1000 system uses a unique token passing strategy to effect a multi-priority
token protocol for peer-to-peer communications. The system passes a tokenbetween panels to control message access on the network. This effectively employsthe power of all panel controller modules to maximize network through-put andminimize system response time.
Simplified Operator Interface Two types of Operator Interface (OI) modules are available for the XLS1000 system:• A Liquid Crystal Display (LCD) with Fire Alarm Common Controls, a numeric
keypad, and special function keys. This OI allows the operator to view statusinformation on Alarm, Supervision, Trouble and Non-alarm inputs (Monitor), andperform common control functions. LCDs are optional.
• Control Display Modules (CDMs) that provide traditional operator controls anddisplays, using LEDs and switches. CDMs are optional.
Programming A System Definition Utility (SDU) allows a system designer to quickly create projectspecific software. The Windows based SDU is capable of any-point-to-any-point
programming and has the power to simplify custom programs.
The SDU uses a four step development process to define job specific requirements:• Step One: Define project parameters such as language, network communication
class, market place, and function timing.• Step Two: Configure cabinets, network routing, local rail modules, field devices,
and communication ports.• Step Three: Define objects including Time Controls, Sequences, and Logical
Zone groups, AND groups, Matrix groups, Service groups, and Check-in Groups.• Step Four: If required, develop rules to establish relationships between input and
output identities.
-
8/19/2019 XLS1000 System Description (4) (1)
7/30
XLS1000 SYSTEM DESCRIPTION
3 74-245
NOTE: Rules are a programming technique to relate inputs to controlled outputs.
System designers can program XLS1000 systems with:• Local or Proprietary Operation• Display by zone or point.• Alarm Verification Sequence by device or hardwire circuit• Water flow Alarm Sequence with or without silenceable signals• Manual and Automatic Alarm Silence affecting programmable audible and visible
Notification Appliance Circuits (NACs)• Alarm Silence Inhibit periods for alarm silence and paging (separate timers)• Global, Group, or individual panel Evacuation Control• Common, Specific, or Function Event program responses• Current, Delayed, or Sequenced Relay Control• Manual Relay Control for Hand/Off/Auto into one or two Control Relays• Logical Zone Groups, AND Groups, Matrix Groups, Service Test Groups• Time Controls, Check-In Groups, Guard Patrol, Non-Fire Alarm Monitoring
XLS1000 Hardware
The modularity and flexibility of the XLS1000 will satisfy both new construction andretrofit applications. It has the capability of supporting a wide range of functional
applications through both intelligent and conventional circuits. With integrated Digitaaudio and the ability to network panels, the XLS1000 can be easily expanded frommedium to very large applications.
Panel Assembly
BOX
CHASSISLOCAL
RAIL
MODULESCONTROL
DISPLAY
MODULES
INNER
DOOR
COVER
OUTER
DOOR
Fig. 3. Panel Assembly with Interface and Connection Layers.
The Panel Assembly consists of:
• Cabinet (Enclosure) Back Box and Doors• Chassis• Power Supplies• Local Rail modules (LRM)• Interface layer for operator interface components
-
8/19/2019 XLS1000 System Description (4) (1)
8/30
XLS1000 SYSTEM DESCRIPTION
74-2450 4
Local Rail Modules
Local Rail Modules (LRMs) provide an interface between the field devices, theOperator interfaces, the panel communications bus (Rail) and the CPU
General features of all the rail modules include:• Plug onto rails on the chassis
• Secured by snap-fit mechanisms to the rail without tools• Use removable field wiring terminal strips for ease of servicing• Use surface mount technology to minimize size and power needs• Support any type of Control Display Modules (the CPU supports the LCD
Operator Interface as required)
The Local Rail Modules include:• Central Processor Unit• Dual Signature Data Controller (DSDC)• Off Premise Signaling (OPS) Module• Power Supply Monitors (PSMON)• Conventional Hardwired Input/Output module (Initiating Device Circuit [IDC8/4])• CDM Rail Interface Module (LED Display Support Module [LDSM])• 15 Watt Zone Amplifier (refer to 74-2451 XLS1000 Audio System Description)• 30 Watt Zone Amplifier (refer to 74-2451 XLS1000 Audio System Description)
Removable
Terminal Blocks
Local Rail Module
Local Rail
Fig. 4. LRM on Rail Assembly.
Central Processing Unit (CPU) The CPU controls communication with:
• The LRMs on the Rail• Other CPUs on the Network via RS-485 Bi-Directional network interface card at
the rate of 38,400 Baud• Remote Ancillary equipment via RS-232 communications card on the back of the
CPU.• Contains the Operating System and all job specific software and supports
expanded memory if required.• Features:
— Built in self test functions — Monitors ground faults — On board LEDs for trouble shooting
-
8/19/2019 XLS1000 System Description (4) (1)
9/30
XLS1000 SYSTEM DESCRIPTION
5 74-245
— Trouble contact controlled by processor in a fail safe mode — Internal real time clock — A built in watchdog timer — Supports the optional LCD if required.
Dual SIGA Data Controller The Dual SIGA Data Controller (DSDC) is a Local Rail Module that providesXLS1000 with an interface between Signature Series Devices and the CPU
3-DSDC
SIGA
DataCard
Dual SIGAData
Controller
Fig. 5. 3-DSDC Dual SIGA Data Controller.
The DSDC features:• One loop card (on back of module) that supports up to 250 Signature devices• Up to five DSDCs per node• Fast loop alarm response is 750 ms• Class A (Style 7) or Class B (Style 4) wiring
• T-Tapping allowed on Class B• Ground fault detection by loop and by remote circuit• Nonvolatile memory for program and configuration data
The fast alarm response allows a reduced loop data communication speed and inturn allows minimized wiring specifications. Thus loop circuits do not require twistedor shielded wire and may be run up to 4750 feet.
NOTE: Loop calculations are required for various applications that can reduce thiswire run.
The DSDC supports a standalone mode for Signature Devices. Should datacommunication fail to remote devices, the loop controllers reconfigure their circuitsso that they can receive a traditional type of alarm.
Signature Data Circuits have electronic short circuit protection and are powerlimited. Wiring may be Class B or A. NFPA style numbers are dependent on yourdevice selection.
By using isolator (bases) loop wiring can be Style 7. Isolators are usually used withClass A circuits but also support mixed wiring styles such as Class A risers andClass B floor area wiring.
-
8/19/2019 XLS1000 System Description (4) (1)
10/30
XLS1000 SYSTEM DESCRIPTION
74-2450 6
Class A Signature Data Circuit
FIRSTFLOOR
THIRDFLOOR
FOURTHFLOOR
SECONDFLOOR
SIGA-SB
orSIGA-RB
SIGA-SBor
SIGA-RB
SIGA-SBor
SIGA-RB
SIGA-SB
orSIGA-RB
SIGA-SB
or
SIGA-RB
EST
EST
EST
EST
EST
EST
EST
EST
EST
EST
SIGA-IB
SIGA-IB
SIGA-IB
SIGA-IB
SIGA-IB
This section is effectively removedfrom the Signature Data Circuit.
SHORTCIRCUIT
Fig. 6. Data Circuit.
Off Premise Module (OPS) The Off Premise Module is a Local Rail Module that provides the XLS1000 withinterfaces for central stations and municipal loops.
The Off Premise Module provides:• Support of old and new style reverse polarity central station connections• Reverse polarity outputs for alarm, supervisory, trouble• City box operation (Local Energy)• Electronic current limiting
3-OPS
Fig. 7. 3-OPS Off Premise Module.
-
8/19/2019 XLS1000 System Description (4) (1)
11/30
XLS1000 SYSTEM DESCRIPTION
7 74-245
When configured for an old reverse polarity style central station connection, only thealarm relay is active. In the normal state, the alarm circuit output is 24 Vdc currentlimited to 6 mA. In the alarm state, the polarity reverses. Should the panel go intotrouble from the normal state, the voltage is removed from the output terminals.When the central station detects a loss of voltage the condition is due to paneltrouble or a line failure. An alarm has priority over trouble (an alarm is transmittedwhen the panel is in trouble).
124 35678910
(+) ALARM Polarity ReversesTROUBLE Power OffALARM has Priorityops2.ai
Fig. 8. Central Station/Old Style.
When configured for a new style reverse polarity style central station connection, thOPS outputs three independent reversing polarity signals. These are alarm,supervisory, and trouble. In each case, an active condition causes the terminaloutput voltage to reverse. Should the central station detect a loss of voltage the
condition is due to a line failure.
124 35678910
(+)
(+)
(+)
ALARM
TROUBLE RELAY TERMINALS 1 & 2
TROUBLE
SUPERVISORY ops1.ai
Fig. 9. Central Station/New Style.
The OPS has terminals for the connection of a local energy master fire alarm box.The module operates into a 14 Ohm coil and supervises the city tie connection foropen conditions.
TROUBLE RELAY
TERMINALS 1 & 2
124 35678910
MUNICIPAL CIRCUIT
(+)
MASTER BOX
ops3.ai
Fig. 10. Local Energy Master Fire Alarm Connection.
-
8/19/2019 XLS1000 System Description (4) (1)
12/30
XLS1000 SYSTEM DESCRIPTION
74-2450 8
Power SupplyMonitor Module The Power Supply Monitor Module is an LRM, that communicates the status of itself
and its related power supply to the CPU over the local rail. A cable connects theMonitor Module and its related power supply placing the supply output power on thelocal rail.
The Power Supply Monitor Module:• Interfaces power supply to CPU• Monitors:
— Input voltage — Output voltage — Rail and auxiliary outputs — Battery voltage — Remote battery temperature — Output current
• Controls: — Battery charge rate — Battery switch over — Power kill on standby when battery depleted
Large batteries (over 17 Ah) mount in remote battery boxes as their physical sizeexceeds the capacity of the panel cabinets. To maintain charger temperature
compensation, a remote temperature probe connects to the primary power supplymonitor LRM terminals.
Conventional InitiatingDevice Circuit Class B (Style Y) The IDC8/4 is an LRM that supports the connection of conventional hardwired
circuits to the rail and in turn to the CPU. The IDC8/4 has eight supervised Class Binput circuits (IDCs). Four of the eight input circuits may be configured as outputcircuits (NACs). The IDC8/4 is ideally suited for retrofit applications when it isdesirable to migrate existing conventional circuit wiring into an XLS1000 panel.
3-IDC8/4
Fig. 11. 3-IDC8/4 Conventional Initiating Device Circuit Module.
The IDC8/4 features:• Support for a CDM module• Eight Class B input circuits• Four circuits can convert to Class B output circuits• Latching or non-latching operation by circuit• Verified or non-verified operation by circuit
-
8/19/2019 XLS1000 System Description (4) (1)
13/30
XLS1000 SYSTEM DESCRIPTION
9 74-245
• Nonvolatile memory for configuration data• Continual internal self checks
Initiating Device Circuits The IDC8/4 supports Style B circuits of the following IDC functionality: alarm,supervisory, and monitor.
As an alarm circuit, the IDC8/4 supports the operation of N.O. contact devices andcompatible conventional Two wire smoke detectors. You can mix contact devicesand smoke detectors on the same verified or non-verified circuit. The verificationperiod is individually adjustable up to two minutes in four second increments.
UL/ULC Listed
4.7KΩ EOL
B401BBase
Connect to IDC 3, 4, 5, or 6IDC/NAC 1, 2, 7, or 8
6251B-001ABase
1 4
2 3
INITIATING DEVICE CIRCUIT (IDC)
Fig. 12. Initiating Device Circuit.
As a supervisory circuit, the IDC8/4 operates with N.O. supervisory contacts. Youmay define the operation as latching or non-latching.
As a monitor circuit, the IDC8/4 operates with N.O. contact devices. Combined witha non-latching operation, the circuit is a supervised event follower and supports theannunciation of critical fan and damper operations.
Circuit annunciation may appear on the LCD, the CDMs, or at any other displaydevice on the network.
When combined with other operating features the IDC8/4 has these advantages:
• Smoke and contact devices mixed on verified circuits• European operation (short as trouble)• Operation of virtually any competitive smoke detector by adjusting impedance
level. Smoke detectors require UL compatibility listing.
Four of the eight circuits of the IDC8/4 can convert to Style Y NACs. This is atraditional reversing polarity circuit for the operation of polarized horns, bells, andstrobes. Each pair of output circuits can distribute 24 Vdc power from the rail or asingle riser source (hardware controlled). The riser source could be a pulsed powersource for audible appliances (such as 3-3-3) or an audio source for speakers.
-
8/19/2019 XLS1000 System Description (4) (1)
14/30
XLS1000 SYSTEM DESCRIPTION
74-2450 10
I D C / N A C # 1
I D C / N A C # 2
I D C # 3
I D C # 4
N A C I N 1 / 2
ToTB1onModule
1 2 43 5 6 7 8 9 10
I D C / N A C # 8
I D C / N A C # 7
I D C # 6
I D C # 5
N A C I N 7 / 8
124 35678910
TX JP1
JP3
11
11
22
22
33
33JP2
JP4
RX
TB1
TB2
Fig. 13. IDC8/4 Converted for Notification Appliance Circuit.
Each NAC has a rating of 24 Vdc at 3.5A or 70 Vrms at 100W. Circuit power limitingis electronic and based on power rather then just current. For example, at 24 Vdcthe current limits at 3.5A, but at 20 Vdc the current limits at 4.2A. This feature allowsthe XLS1000 to better support strobe devices that exhibit an increasing current as
voltage declines. The lower voltage condition exists only when the system is onstandby and the battery is approaching the extent of its capacity.
-
8/19/2019 XLS1000 System Description (4) (1)
15/30
XLS1000 SYSTEM DESCRIPTION
11 74-245
UL/ULC Listed15KΩ EOL
Connect to IDC/NAC 1, 2, 7, or 8NOTIFICATION APPLIANCE CIRCUIT (NAC)
Fig. 14. Notification Appliance Circuit.
LED DisplaySupport Module (LDSM) A Control Display Module may plug into any LRM for connection to the power and
data buses. Since CDM points are defined in software, any CDM can plug into anyunderlying LRM. If no LRM is available, then a LED Display Support Module (LDSMmust first be plugged into the local rail to provide power/data bus connections to theCDM.
Power Supplies
XLS1000 Power Supplies are high efficiency (>80%) switch mode units that canoperate in parallel to supply the local rail. The parallel operation of power suppliesincreases power distribution efficiency. A power supply is made up of two sub-assemblies; a power supply, and a power supply monitor (LRM).
Within a panel, a power supply may function as a primary or a booster. Only oneprimary power supply may exist in a node. A panel can have up to three boosterpower supplies. The primary power supply performs voltage regulation for itself andfor the additional booster supplies. Power supplies are available for 120 or 230 Vacoperation. The frequency range is 50 to 60 Hz.
The power supply provides:• Output of 24 Vdc at 7 Amp, filtered and regulated to
-
8/19/2019 XLS1000 System Description (4) (1)
16/30
XLS1000 SYSTEM DESCRIPTION
74-2450 12
above 25 Vdc. During standby operation, if the battery voltage falls to 18 Vdc, theprimary power supply shuts down the panel in an orderly fashion.
If the battery shorts, the charger automatically disables itself and causes a troublethrough the battery voltage (low) monitor. The system will constantly pulse thebattery and try to restore it. Should the short condition clear the systemautomatically restores.
Booster power supplies have specifications similar to primaries excepting they donot have a battery charger, and they are regulated by the primary power supplieselectronics. Load sharing by the power supplies improves cost effectiveness byeliminating the problem of power distribution (unused power at a supply). Loadsharing between power supplies is within 5%.
Power supplies monitor the temperature of their heat sinks and switch to standbywhen the temperature exceeds specifications. The system reports power supplytrouble to the CPU. This trouble clears when the heat sink cools and the powersupply automatically switches back to normal operation. Power Supplies mount tothe back of the wall box on dedicated footprints. Each power supply has a relatedPower Supply Monitor Module that takes one rail space.
Chassis The chassis supports the Upper and Lower rails. The rails carry power and data.
The upper rail carries 5V power, system data, audio data, and supports autoaddressing of rail modules.
LRM
+5V Common
Data +
Data -
Addr Select +
Addr Select -
Audio Data +
Audio Data-
+24V
Ground
All Fail
Local Rail
The lower rail carries a 24V power common, earth ground, and supports an all failline. Using the all fail line, any module receiving an alarm can alert the system of theevent if communication with an LRM fails.
Chassis assemblies:• Mount to wall box• Provide mounting locations for power supplies, CPUs, and LRMs• Use top and bottom rail buses to distribute power, system data, audio data, and
have dedicated signal lines for auto module addressing and data communication
failure• Use a seven module space rail with standard 19 inch rack mount except for
CHAS-4 used with ASU or FTCU
Operator Interface Modules The Operator Interface modules make up the operator layer of the XLS1000System. The interface consists of:the LCD Operator Interface module and theControl Display Module (CDM). Both modules focus on the emergency user,providing:• Important information first• Hands-free first highest priority event• Last highest priority event always displayed
-
8/19/2019 XLS1000 System Description (4) (1)
17/30
XLS1000 SYSTEM DESCRIPTION
13 74-245
• User selectable information• Simple lights and switches
LCD Operator Interface Module An LCD Operator Interface module provides Fire Alarm Common Controls throughan eight line by 21 character back-lit Liquid Crystal Display, special function keys,and keypad. Its use in a node is optional.
1 2 3
654
7 8 9
0
Power Test
Reset Alarm
SilencePanel
Silence Drill
DisableGNDFault
CPUFail
MoreDetails
CommandMenu
Previous
Message
Next
MonitorTroubleSup'yAlarm
Fig. 15. LCD Operator Interface.
The LCD Operator Interface module provides:• A graphical, backlit LCD with eight lines of 21 characters (168 total characters)• Queues to sort events by type• A hands-free display of the first event of highest priority• A continuous display of the last alarm event; even when viewing other message
types• Five general system status LEDs• Four common control LED switch controls• Four queue selection LED switch controls• Queue event review with previous and next keys• More Details key displays logical zone group contents• Command Menus key to display the menu system
See the Operations section for a description of system operation.
There are four fundamental types of LCD Display:• 24 LED, 24 label module• 12 LED, 12 pushbutton, 12 label module• 18 LED, 18 pushbutton, six label module arranged in six groups of three
pushbuttons
-
8/19/2019 XLS1000 System Description (4) (1)
18/30
XLS1000 SYSTEM DESCRIPTION
74-2450 14
CDMs feature:• A Lexan assembly that snap fits to LRMs• A ribbon cable connection to supporting LRM• Individual hinges for access to LRM field wiring terminals• Membrane construction with tactile switches• Slide-in labels
Each CDM offers the following traditional zone annunciation; and emergency usercontrol of notification, paging, and auxiliary controls:• Flash rates programmable• Flash rates: off, slow, fast, steady on• Membrane style tactile pushbuttons• Software support for toggle and latching interlock switch action• Supervised position and type• Lamp test• Zone display of alarm, supervisory, and monitor• Control of page and auxiliary outputs
Each CDM has a door with sliding latches, providing technicians with quick accessto the terminals of the underlying LRM for metering and trouble shooting.
Enclosures
There are two types of XLS1000 enclosures: Lobby mount and Remote (ElectricalCloset) mount.
Lobby Enclosures have a modern contour design with viewing window and areavailable in an attractive white or red baked enamel finish making them suitable formounting in areas of high visibility.
Enclosures are described as five or seven space that refers to the box width by thenumber of LRMs that can mount to a single rail chassis assembly. For a sevenspace box, the basic box assemblies can have one, two, or three chassisassemblies. Another way of referring to the box sizes is by the LRM count of 7, 14,and 21.
The lobby mount enclosure features include:• Attractive design• Four standard size enclosures• Module space size to accommodate 5, 7, 14, and 21 modules• Lexan viewing windows• A Honeywell keyed lock• The capability of handling audio equipment; including distributed amplifiers• Space for a large battery (up to 17 Ah) Larger Batteries mount in a separate
cabinet for remote battery mounting (up to 55 Ah)
The electrical closet mount enclosure features include:• Three standard size enclosures• Fire red or White, baked enamel finish• Module space size to accommodate 7, 14, and 21 modules• The capability of handling audio equipment; including distributed amplifiers• Bottom space for 55 Ah battery
5 Space Enclosure • Box: 22.37 in. High x 14 in. Wide x 3.86 in. Deep• Door: 24.25 in. High x 16.4 in. Wide x 1.65 in. Deep
7 Space Enclosure • Box: 23.25 in. High x 24 in. Wide x 4 in. Deep• Door: 25.50 in. High x 27.375 in. Wide x 2.5 in. Deep
14 Space Enclosure • Box: 35.50 in. High x 24 in. Wide x 4 in. Deep• Door: 37.75 in. High x 27.375 in. Wide x 2.5 in. Deep
21 Space Enclosure • Box: 47.75 in. High x 24 in. Wide x 4 in. Deep• Door: 50.00 in. High x 27.375 in. Wide x 2.5 in. Deep
-
8/19/2019 XLS1000 System Description (4) (1)
19/30
XLS1000 SYSTEM DESCRIPTION
15 74-245
System Operation
All XLS1000 operating functions are controlled by its powerful, highly flexible systemsoftware. This provides an ability to easily load options during system design andinstallation. This on-site flexibility allows for operational changes and upgradesyears after the initial installation at a lower cost to the owner.
1 2 3
654
7 8 9
0
Power Test
Reset Alarm
SilencePanel
Silence Drill
DisableGNDFault
CPUFail
MoreDetails
CommandMenu
Previous
Message
Next
MonitorTroubleSup'yAlarm
System Status Five system status LEDs display the general condition of the system.
Power TestCPUFail
GndFault
Disable
LED Description
Power Green—On when AC power is on.
Test Yellow—On when any portion of the system (Group) is under test.
CPU Fail Yellow—On when CPU stops running.
Gnd Fault Yellow—On when a ground exists on the system (Group).
Disable Yellow—On when any point or zone is disabled by a user.
Common Controls Four LED switch controls provide system common control. System designers maydefine the features as Local, Group, or Global.
-
8/19/2019 XLS1000 System Description (4) (1)
20/30
XLS1000 SYSTEM DESCRIPTION
74-2450 16
Local means the function executes only within its node. For example, if a singlepanel serves a building and exists on a network, then operating Reset (at that panel)resets that panel only.
Group means the function executes the function over a defined node list. Forexample, consider a panel on a multi-building network, and serving a building withfour other panels. In this case, operating Reset at the buildings main panel wouldreset the five panels in that building but affect no other panels on the network.
Global means the function operates across the network and affects all nodes.
Reset
Pressing Reset starts the systems reset sequence. The yellow LED flashes duringthe first phase of reset and turns on steady for the second phase. The LED turns off
when the system is normal.
AlarmSilence
Pressing Alarm Silence turns off all Notification Appliance Circuits (NACs) definedas audible. The yellow LED turns on when silence is active.
PanelSilence
Pressing Panel Silence turns off the systems audible signal. The yellow LED turnson when panel silence is active and a trouble condition exists. The panel audiblesignal sounds user programmable signal rates for alarm, supervisory, trouble, andmonitor conditions.
Drill activates the fire drill sequence. Audibles and visibles sound in a commonevacuation mode. But the remote connection is not activated.
NOTE: This button is optionally programmable, so operation may vary dependingupon the program.
-
8/19/2019 XLS1000 System Description (4) (1)
21/30
XLS1000 SYSTEM DESCRIPTION
17 74-245
12:12:12 04-25-96
ALARM HISTORY 0000
HONEYWELL
XLS1000
In the normal condition the LCD may display user selected information, such as thedate and time plus a system title. The title is optional and may appear on lines fourand five.
When the system is off normal, the display has four logical areas.
12:12:12 A00002 D0000
0002 ALARM ACTIVE
LOCATION MESSAGE LINE1
LOCATION MESSAGE LINE2
0001 ALARM ACTIVE
LOCATION MESSAGE LINE1
LOCATION MESSAGE LINE2
A002 S000 T000 M000
System StatusWindow
Current Event Window
Last Event Window
Type Status Window
}
}
}}
A005
12:19:12 A00002 D0000
0005 WATERFLOW ACTIVE
PAINT SHOP
NORTH ENTRANCE
0001 PULL STN ACTIVE
PAINT SHOP
S001 T000 M000
The first area (line one) is the System Status Window. This area of the displayshows the time, the number of active points (A), and the number of disabled points(D).
The second area (lines two through four) is the Current Event Window. This areaautomatically displays the first active event of the highest priority if the user has nottaken control of the system. Once the emergency user takes control, this windowdisplays the related message for each event the user selects for view.
Line two displays system event information. In the sample above we have shownthe chronological number of the event within the queue. 0001 is the first alarm and0005 is the fifth. The type of event (PULL STN), follows the event number.
PreviousMessage
Next
-
8/19/2019 XLS1000 System Description (4) (1)
22/30
XLS1000 SYSTEM DESCRIPTION
74-2450 18
The NEXT key displays the second alarm message. The next message scrolls intothe second area. However, the last alarm event always remains in view.
The third area (lines 5, 6, and 7) is Last Event Window. The format of this area issimilar to that of the second area. The thrid area always displays the last highestpriority event received at the display. No matter what queue the user selects forview, the LCD always displays the most recent alarm. A new alarm event resoundsthe panel audible signal and appears immediately on display without overwritinginformation the user selected for view.
The fourth area (line 8) is the Type Status Window. This area shows the totalnumber of active events by queue type. A is for alarm, S is for supervisory, T is fortrouble, and M is for monitor. The number following each letter is the number ofactive events existing in each queue.
Queues The XLS1000 System sorts events by type into queues and automatically displaysthe first event of the highest priority type. The priority is: alarm (Highest),supervisory, trouble, and monitor(Lowest).
Queue selection controls allow the user to view events by type. This avoids anemergency user wasting time scrolling through an interleaved event list to look atalarms or confusing an alarm message with other message types.
Alarm MonitorTrouble Supervisory
Some competitive systems sort events by type but display them in a common list.This means an emergency user must scroll through all alarms to view supervisory,trouble, or monitor messages. The opportunity exists to confuse message types.
More Details More details are available for additional information on points in the zone group. Ifthe More Details key is pressed, the device with the lowest address displays in thefirst window. If multiple devices are active, users may scroll through the list. If theactive device is a single device (not a zone), More Details will show the deviceaddress.
MoreDetails
12:12:12 A00005 D0000
PULL STN PPCCDDDD
0005 FIRE ALARM
0001 PULL STN ACTIVE
004 TO VIEW MORE 001
WEST STAIRWELL EXIT
A005 S000 T000 M000
Users can exit the device level display by pressing any queue control key, the MoreDetails key, or by backing out using the scroll key at the first message.
Command Menu For Maintenance Users, the XLS1000 provides a hierarchical menu system thatprovides powerful tools for system management, reports, and trouble shooting.
Pressing the Command Menu key displays the main menu. The Command Menu isPassword protected. The maintenance user may choose an item by:
-
8/19/2019 XLS1000 System Description (4) (1)
23/30
XLS1000 SYSTEM DESCRIPTION
19 74-245
• Pressing the item number and pressing enter• Scrolling the reverse highlight down to a choice and pressing enter.
MAINMENU
2)ENABLE
6)REPORTS
1)STATUS
3)DISABLE 4)ACTIVATE
5)RESTORE
009 SCROLL FOR MORE 001
Menu Functions:1. Status2. Enable3. Disable4. Activate5. Restore6. Control Outputs
7. Reports8. Program9. Test
The user exits the menu system by pressing any key not used during menuoperations. Examples include queue select keys, and the command menu key. Theuser may also backspace out of the menu system.
LCD Display Operation The operation of the LCD Display depends on the system definition. If the system isproprietary, then the user must acknowledge all events that appear on the systemby viewing each event. Once the user acknowledges all active events, then thepanels internal audible signal silences.
If the system is local, then the systems internal signal silences when the userpresses panel silence or a scroll key. If unviewed events exist in a queue, the queue
LEDs continue to flash to inform the user of unseen events.
When all events in a queue are acknowledged or seen, the queue LED associatedwith the queue turns on steady. If a subsequent event occurs, the new eventresounds the panel signal and flashes the queue LED.
If you define Logical Group Zones for the system, then each alarm zone hascontents made up of two or more alarm devices (such as detectors or pull stations).
For its default operation, the LCD displays the zone. Each zone only displays once,regardless of the number of devices active within the zone. Any system responsescreated at the device level still execute.
Control Display Module You can expand the common controls beyond the LCD Display faceplate by addinga Control Display Module (CDM) and assigning features to its switch controls. AllCDM Switches and LEDs are under program control and therefore operation isdependent upon the program.
System Power Up
Upon initial power up the system tests whether the initialization is planned orunplanned as in a warm restart. Given a planned startup the system checks itsapplication code, and if good, loads it. It then checks and loads the operatingsystem, runs tasks, and checks the database for accuracy. As all the tasks initializethey report to the watchdog timer which then begins continuous monitoring of CPUoperation.
-
8/19/2019 XLS1000 System Description (4) (1)
24/30
XLS1000 SYSTEM DESCRIPTION
74-2450 20
System Supervisor
During system operation, continuous software supervision occurs in thebackground. The system monitors all tasking operations, checks all resources,supervises the accuracy of code, database, and tables.
Fire Alarm Operations
Automatic alarm operations take place without intervention by a user. They provideoccupant and building protection by unattended life safety fire alarm systems. Theirbasic purpose is to monitor the building environment and evacuate occupants if ahazard is detected. Additional features, such as city ties, environmental interfacecontrols, and audio support enhance the chances of safe occupant evacuation andextend the function of the system to property protection.
Supervisory Operations
Supervisory device/circuits monitor critical functions of a sprinkler system.Supervisory initiating devices must be N.O. contacts which close on activation inorder to meet North American codes and standards.
System sources of supervisory inputs include device transponders and traditionalcircuits defined as supervisory.
Monitor Operations
Monitor inputs follow the status of remote equipment. In most applications, auxiliaryoutput from the FA system causes changes in building HVAC operation. Monitorinputs display the results to emergency users. Typical examples include the statusof a fan, or the position of a damper.
Monitor displays can be inhibited when the system is not in alarm. Monitor circuitsare supervised.
On a local system, monitor events queued for display are non-latching. Event
restoration removes the monitor event from the display.
On a proprietary system you must acknowledge monitor events and theirrestoration.
Optional Operations
Check-In Group A Check-In Group helps staff monitor the state of being of building occupants. It isuseful in age care facilities, prisons or other secure environments where a personmay be at risk.
The XLS1000 allows programming of a check-in period. During this period all listedindividual stations are expected to activate. Any station not activated by the end ofthe check-in time period will initiate a check-in alarm.
For example, in a living facility for seniors, you could program a check-in periodbetween 6:00 am and 10:00 am. As part of their morning routine, a residentoperates a station (switch) during the check-in period. At the end of the period, forstations which did not check-in, the system initiates a check-in response and liststhe delinquent stations on the LCD display. When staff investigates the delinquency,they restore the station by operating it. Outside of the check-in period, a stationactivation generates an emergency response.
In a prison environment, you could monitor the state of being of guards. In this caseyou may wish to have much tighter check-in cycles, say one hour, and a shorter
-
8/19/2019 XLS1000 System Description (4) (1)
25/30
XLS1000 SYSTEM DESCRIPTION
21 74-245
check-in period of five minutes. As well you could set up multiple check-ins, sayonce an hour.
The check-in station is a non-latching Signature Module with personality code 3. It isavailable in various configurations such as a pull cord or an emergency push. Thepull cord device must be non-latching.
Guard Patrol The Guard Patrol feature provides a means to help monitor the state of being ofguard on a patrol tour. It minimizes the time that could elapse between a guardbeing disabled (attacked) and notification of delinquency (early, late, or out ofsequence station activation) at a panel location.
With XLS1000 Guard Patrol feature you can:• Program up to 255 guard patrols• Each patrol station may exist on one guard patrol• Each guard patrol can have up to ten patrol routes• Each route can have up to 63 patrol stations.
A patrol route is a set number of patrol stations arranged in a particular sequence. Apatrol route has the same stations as its parent guard patrol, however, a systemdesigner can alter the path that a guard follows in activating the stations. The firststation of a patrol route must be different from all other routes in a guard patrol.
For example:
Station Patrol Tour Sequence
Route Number 1 2 3 4 5 6 7 8 9 10
Tour 1 GS1 GS2 GS3 GS4 GS5 GS6 GS7 GS8 GS9 GS10
Tour 2 GS10 GS9 GS8 GS7 GS6 GS5 GS4 GS3 GS2 GS1
Tour 3 GS2 GS3 GS4 GS5 GS6 GS7 GS8 GS9 GS10 GS1
Up to 10 Tours Include all stations in each route. GS = Guard Station
A system designer programs an early and late period for each guard patrol stationon a route. For example, the early period for a station may be two minutes and thelate period might be three minutes from the activation of the previous station. This
means if a guard operates the next station before two minutes the system activatesan early security message. If the guard does not activate the station before threeminutes elapses the system activates a late security message. If the guard operatesthe ‘wrong’ station (not the next in the programmed route) the system activates anout of sequence security message.
The early-late periods for each station can be different for each route. This gives thedesigner the flexibility to have both long and short routes (times) to the same stationfrom various previous stations.
Users can start a guard patrol in two different ways. First, from the panel; secondfrom the first station of a route.
For a patrol start from the control panel, the user may initiate a patrol through themenu system. The user selects guard patrol and then chooses the patrol (one of up
to ten). The patrol guard must then activate the first station between a programmedearly time and a programmed late time. The guard must then operate the secondstation between similar early and late periods. Similar conditions exist for eachpatrol station until the guard operates the last station.
The second method of starting a patrol merely requires the guard to activate the firsstation on a route. A successful guard patrol requires the guard to operate eachstation of the route within the programmed periods and in the proper order.
The guard patrol station is a latching Signature Module with personality code 4.
-
8/19/2019 XLS1000 System Description (4) (1)
26/30
XLS1000 SYSTEM DESCRIPTION
74-2450 22
System Definition Utility
The System Definition Utility (SDU) software allows a system designer to quicklycreate project specific software. The Windows based SDU is capable of any-point-to-any-point programming, yet has the power to simplify a custom program.
The System keeps track of users, jobs, versions, and time against projects. Market
place definitions provide fundamental system definitions for various geographicalareas. The SDU configures the system variables to meet differing coderequirements.
Using the SDU the designer can configure:• Signature Circuits:
— Sensitivity — Alarm Verification — Device Operation:
+Water flow+Supervisory+Monitor
• Cabinet (Panels): — Types — Labels
• Network (Routing) (Groups)• Groups:
— AND — Check in — Guard Patrol — Matrix — Service — Zones
• Time Controls• Reports• Audio Messages
There are various ways to define relationships between input and output devicesand circuits. Simple single stage, general evacuation systems have outputs withcommon operations. By defining outputs as common alarm, you make the devices
activate on any alarm input. No further programming of common devices is required.
Larger systems can have multiple stages and zoned operations. In many cases,devices in a zone all cause the same system response. Rather than program at thedevice level, the SDU allows the system designer to group the devices into zonesand then program at the zone level. Besides supporting traditional zoneannunciation, this feature dramatically reduces the number of correlations requiredto outputs.
To further simplify programming, the SDU uses labels instead of point addresses.This allows a system designer to use descriptive text to relate inputs and outputsusing rules. Rules allow relating inputs to outputs using simple programmingtechniques. Devices, circuits, and zone can all have reference labels. By using wildcards, numerical operators, and carefully crafted labels, the programmer canreplicate system operations over symmetrical zones.
The programming steps the SDU uses in a development process to define jobspecific operations:• Step One: Define system parameters such as network communication class,
language, and passwords.• Step Two: Define panels (nodes) on the network. Configure hardware modules
and loop devices.• Step Three: In a spreadsheet format define objects. Objects include zones,
logical groups, AND matrices, time controls, sequences, and service groups.• Step Four: If required, uses rules to establish relationships between input and
output objects.
-
8/19/2019 XLS1000 System Description (4) (1)
27/30
XLS1000 SYSTEM DESCRIPTION
23 74-245
System Architecture Configuration and Sizing
Smallest Node • One CAB5 enclosure with five local rail module slots• One Panel Control Module CPU (two LRM slots) required• One PSMON Power Supply Monitor (one LRM slot)• One 7 Amp power supply• Two LRM slots for function modules
• One or two DSDC Dual SIGA Data Controllers (one SIGA circuit for eachcontroller)
• Up to 125 sensor and 125 module addresses per Signature Data Circuit• Up to 2 X 8 = 16 hardware circuits of which eight could be NACs• Up to two RS-232 ports• Up to 2MB of RAM, 2MB of Flash, 32Kb of EEPROM• An optional 168 character LCD• Up to 3 X 24 = 72 LED zones• Up to 3 X 12 = 36 LED/Sw (2 X LEDs)• Up to 3 X 6 = 18 On/Auto/Off group controls• Up to 10 Ah of standby power from a single battery set mounted in this enclosure
Node • One enclosure with up to 21 local rail module slots• One Panel Control Module CPU (two LRM slots) required• Up to two RS-232 ports
• Up to 2MB of RAM, 2MB of Flash, 32Kb of EEPROM• Up to five Dual SIGA Data Controllers each with one SIGA loop• Up to 625 SIGA sensors and 625 SIGA modules (1250 points total)• Class A (Style 7) or Class B (Style 4) wiring• Loop alarm detection
-
8/19/2019 XLS1000 System Description (4) (1)
28/30
XLS1000 SYSTEM DESCRIPTION
74-2450 24
• 15 and 30 Watt panel mounted amplifier modules• 25 or 70.7 Volt speaker lines• Each amplifier has a built in 3.5 Amp NAC• Up to 15 X 30 = 450 Watts of zoned audio per node• RS-485 eight channel Audio Communications• RS-485 Audio Communications at 326Kb• Five fire telephones off hook before signal begins to degrade• A maximum of 20 telephones can be off-hook in the call-in queue• Remote telephone busy/ready ring tone from SIGA-CC1
CPU
PSMON
LRM
LRM
1 2 3 4 5
CPU
PSMON
LRM
LRM
1 2 3 4 5 6 7
LRM
LRM
CPU
PSMON
1 2 3 4 5 6 7
LRM
1 2 3 4 5 6 7
LR
M
1 2 3 4 5 6 7
A S U F T
LRM
LR
M
LRM
LRM
LR
M
LRM
LRM
LR
M
LRM
LR
M
CPU
PSMON
LRM
1 2 3 4 5 6 7
LRM
1 2 3 4 5 6 7
LR
M
LR
M
LR
M
LR
M
LR
M
LR
M
LR
M
LRM
CPU
PSMON
1 2 3 4 5 6 7
LRM
1 2 3 4 5 6 7
LR
M
LR
M
ZA
30
ZA
30
ZA
30
C7468 REV
NODE 1 NODE 2
5000 FT MAX. (1, 2)
NODE 3 NODE 4 NODE 64
RCC7
CAB21 CAB21RCC21 RCC21
CAB5 CAB7
CAB14
NOTES:1. 5000 FT (1524 M) MAX./SEGMENT; ALMOST 60 MILES (97 KM) WITH 63 SEGMENTS.2. NETWORK MUST BE DAISY-CHAINED; T-TAPPING IS NOT ALLOWED.
LRM
LRM
LRM
LRM
LRM
BPMON
BPMON
BPMON
BP
MON
BP
MON
BP
MON
BP
MON
Fig. 16. System Architecture Configuration and Sizing.
-
8/19/2019 XLS1000 System Description (4) (1)
29/30
XLS1000 SYSTEM DESCRIPTION
25 74-245
-
8/19/2019 XLS1000 System Description (4) (1)
30/30
Home and Building Control Home and Building Control Helping You Control Your World
Honeywell Inc. Honeywell Limited-Honeywell Limitée
Honeywell Plaza 155 Gordon Baker Road