working instructions - amazon web servicesifixit-documents.s3.amazonaws.com/g4gas5ycnlig6apv.pdf ·...

1222-6716 Rev 3

Working Instructions - mechanical -

W995

� Sony Ericsson Mobile Communications AB – Company Internal

Working instruction (mech)

1222-6716 Rev 3

1 Exterior Views

1.1 W995

� Sony Ericsson Mobile Communications AB – Company Internal 5(96)


1222-6716 Rev 3

2 Tools

SPECIAL TOOLS

1. Torque Screwdriver

2. Bits (T6)

3. Bits (JCIS No. 0)

4. Front Opening Tool

5. Guitar Pick

6. Flex Film Assembly Tool

7. ESD Brush

For part information on the tools above, refer to the ‘Tools Catalogue/Matrix’!

STANDARD TOOLS

1. ESD Tweezers

2. Dentist hook



1222-6716 Rev 3

3 Disassembly

The disassembly is done in the following order: 1. Battery Cover 2. Battery 3. Keyboard 4. Panel Key Dummy 5. Lower Screw Cap 6. Lower Rear Cover 7. BT GPS Antenna 8. Carrier Holder SIM and SIM Flex Assy 9. Camera - Rear 10. Main Antenna 11. Key Flex Assy

12. Main PBA 13. Upper Screw Cap 14. Front Cover Assy (a) and Navi Key (b) 15. Navi Key PBA 16. Display 17. Carrier Holder VT Cam 18. Camera - Front

3.1 Battery Cover Flip over the metal ring.

Push the knob lock in the direction of the arrow to unlock the Battery Cover.



1222-6716 Rev 3


Disassembly

Raise the Battery Cover to remove it.

3.2 Battery Insert the Front Opening Tool and lift the bottom of the Battery to release it.

Remove the Battery.

3.3 Keyboard Turn the phone over and open the slider.


1222-6716 Rev 3

Disassembly

Carefully insert the dentist hook through this hole and lift to release the Keyboard in this corner.

Be careful not to damage the microphone/Key Flex Assy just below the hole in the Keyboard!

Gently peel the Keyboard off by using the tweezers.

Scrap! Not to be reused!

3.4 Panel Key Dummy Remove these two screws by using torx bit no. 6.

Insert the Front Opening Tool and raise the Panel Key Dummy to release it from the phone.



1222-6716 Rev 3

Disassembly

Remove the Panel Key Dummy.

3.5 Lower Screw Cap Turn the phone over.

Carefully insert the dentist hook underneath one of the two Lower Screw Caps and remove it.

Do the same with the second Lower Screw Cap.

3.6 Lower Rear Cover Remove these two screws by using torx bit no. 6.



1222-6716 Rev 3


Disassembly

Insert the Front Opening Tool as shown in the picture to unlatch the snap hooks.

Use index fingers to pull both sides of the Lower Rear Cover (1) in the direction of arrows and push the Main PBA (2) with thumbs until the bottom side is released.

Lift the Lower Rear Cover and remove it in the direction of the arrow from the Audio Jack.

3.7 BT GPS Antenna Remove the two screws by using the JCIS No. 0 bit.


1222-6716 Rev 3

Disassembly

There are two hooks securing the BT GPS Antenna.

Unsnap this hook by using the Front Opening Tool.

Unsnap this hook by using the Front Opening Tool.

Remove the BT GPS Antenna.



1222-6716 Rev 3

Disassembly

3.8 Carrier Holder SIM and SIM Flex Assy

There are three snap hooks securing the Carrier Holder SIM and SIM Flex Assy.

Unsnap the first hook by using the Front Opening Tool.

Unsnap the second hook by using the Front Opening Tool.

Pull the Carrier Holder SIM little bit in the direction of the arrow (1) and lift to unsnap the third hook (2).



1222-6716 Rev 3

Disassembly

Carefully open the Carrier Holder SIM in the direction of the arrow to get access to the btb connector underneath.

Disconnect the connector by using the Front Opening Tool.

Remove the Carrier Holder SIM and SIM Flex Assy.

3.9 Camera - Rear Disconnect the connector by using the Front Opening Tool.



1222-6716 Rev 3


Disassembly

Remove the Camera.

3.10 Main Antenna The Main Antenna is secured to the Main PBA by two snap hooks.

Unsnap one of the hooks by using the Front Opening Tool.

Remove the Main Antenna.


1222-6716 Rev 3

Disassembly

3.11 Key Flex Assy Insert the Front Opening Tool in this corner to release the Key Flex Assy.

Peel the Key Flex Assy in the direction of the arrow to get access to the btb connector underneath.

Disconnect the connector by using the Front Opening Tool.

Continue to peel off the Key Flex Assy and remove it.




1222-6716 Rev 3

Disassembly

The residues on the Shielding Can Lid and the phone must be cleaned off before reassembly.

3.12 Main PBA Release the bottom of the Main PBA by pushing it from back by using fingers.

Two snap hooks (marked in picture) are holding the Main PBA.

Gently raise the bottom of the Main PBA.

Be careful not to damage the FPC on the back of the Main PBA.

Gently remove the Main PBA and place it next to the Hinge Slider Assy as shown in the picture.



1222-6716 Rev 3


Disassembly

Disconnect the BtB connector by using the Front Opening Tool.

3.13 Upper Screw Cap Carefully insert the dentist hook underneath one of the two Upper Screw Caps and remove it.


Do the same with the second Upper Screw Cap.


3.14 Front Cover Assy and Navi Key

Remove these four screws by using JCIS No. 0 bit.


1222-6716 Rev 3

Disassembly

Insert the Guitar Pick as shown in picture and gently slide back and forth to release this side of the Front Cover Assy.

Continue to slide on this side.

Continue to slide on this side.

The phone and the Front Cover Assy separated.



1222-6716 Rev 3


Disassembly

Remove the Navi Key by using the tweezers.

3.15 Navi Key PBA Remove this screw by using JCIS No. 0 bit.

There are two hooks securing the Navi Key PBA. Insert the Guitar Pick tool to release the Navi Key PBA.

Turn the Navi Key PBA in the direction of the arrow to gain the access to the two connectors.


1222-6716 Rev 3

Disassembly

Disconnect this connector by using the Front Opening Tool.

Disconnect this connector by using the Front Opening Tool.

Remove the Navi Key PBA.

3.16 Display Remove the display by lifting it as shown in picture.



1222-6716 Rev 3

Disassembly

3.17 Carrier Holder VT Cam Insert the dentist hook into the hole to release the hook of the Carrier Holder VT Cam.

Remove the Carrier Holder VT Cam.

3.18 Camera - Front Disconnect the Camera connector by using the Front Opening tool.

Remove the Camera.



1222-6716 Rev 3


4 Replacement

4.1 Battery Cover Follow the 3.1 Disassembly instructions!

Prepare the new Battery Cover.

Follow the 5.18 Reassembly instructions!

4.2 Keyboard Follow the 3.1 – 3.3 Disassembly instructions!

Prepare the new Keyboard.

Follow the 5.16 – 5.18 Reassembly instructions!

4.3 Panel Key Dummy Follow the 3.1 – 3.4 Disassembly instructions!

Prepare the new Panel Key Dummy.


4.4 Lower Screw Cap Follow the 3.5 Disassembly instructions!

Prepare the new Lower Screw Cap.



1222-6716 Rev 3

Replacement

4.5 Lower Rear Cover Follow the 3.1 – 3.6 Disassembly instructions!

Prepare the new Lower Rear Cover.


4.6 BT GPS Antenna Follow the 3.1 – 3.7 Disassembly instructions!

Prepare the new BT GPS Antenna.


4.7 Carrier Holder SIM Follow the 3.1 – 3.8 Disassembly instructions!

Follow the 4.34 Removal instructions!

Prepare the new Carrier Holder SIM.

Follow the 4.34 Installation instructions!


4.8 Camera - Rear Follow the 3.1 – 3.9 Disassembly instructions!

Prepare the new Camera - Rear.





1222-6716 Rev 3

Replacement

4.9 Main Antenna Follow the 3.1 – 3.6 & 3.10 Disassembly instructions!

Prepare the new Main Antenna.

Follow the 5.9 & 5.13 – 5.18 Reassembly instructions!

4.10 Key Flex Assy Follow the 3.1 – 3.6 & 3.11 Disassembly instructions!

Prepare the new Key Flex Assy.

Follow the 5.8 & 5.13 – 5.18 Reassembly instructions!

4.11 Upper Screw Cap Follow the 3.13 Disassembly instructions!

Prepare the new Upper Screw Cap.


4.12 Front Cover Assy Follow the 3.1 – 3.2 & 3.13 – 3.14 Disassembly instructions!

Prepare the new Front Cover Assy.

Follow the 5.5 – 5.6 & 5.17 – 5.18 Reassembly instructions!



1222-6716 Rev 3

Replacement

4.13 Navi Key Follow the 3.1 – 3.2 & 3.13 – 3.14 Disassembly instructions!

Prepare the new Navi Key.


4.14 Navi Key PBA Follow the 3.1 – 3.2 & 3.13 – 3.15 Disassembly instructions!

Prepare the new Navi Key PBA.



4.15 Display Follow the 3.1 – 3.2 & 3.13 – 3.16 Disassembly instructions!

Prepare the new Display.


4.16 Carrier Holder VT Cam Follow the 3.1 – 3.2, 3.13 – 3.14 & 3.17 Disassembly instructions!

Prepare the new Carrier Holder VT Cam.

Follow the 5.2, 5.5 – 5.6 & 5.17 – 5.18 Reassembly instructions!



1222-6716 Rev 3

Replacement

4.17 Camera - Front Follow the 3.1 – 3.2, 3.13 – 3.14 & 3.17 – 3.18 Disassembly instructions!

Prepare the new Camera - Front.

Follow the 5.1 – 5.2, 5.5 – 5.6 & 5.17 – 5.18 Reassembly instructions!

4.18 Hinge Slider Assembly Follow the 3.1 – 3.18 Disassembly instructions!

Prepare the new Hinge Slider Assembly.





1222-6716 Rev 3

Replacement

4.19 Co-Branding Label

Follow the 3.1 Disassembly instructions!

Carry out the replacement as described below.


REMOVAL

Carefully insert the dentist hook underneath the Co-Branding Label and lift to release it.

Remove the Co-Branding Label.

INSTALLATION

Attach a new Co-Branding Label in the cavity.



1222-6716 Rev 3

Replacement: Co-Branding Label

Press to secure the attachment.



1222-6716 Rev 3

Replacement

4.20 MComp Sheet Shade Camera Led

Follow the 3.1 – 3.4 Disassembly instructions!



REMOVAL

Peel off the MComp Sheet Shade Camera Led by using the Flex Film Assembly Tool.

INSTALLATION

Attach a new MComp Sheet Shade Camera Led.

The proper position of the MComp Sheet Shade Camera Led.



1222-6716 Rev 3

Replacement: MComp Sheet Shade Camera Led




1222-6716 Rev 3

Replacement

4.21 Side Key




REMOVAL

Push the Side Key from outside until the key becomes released with the tweezers.

Remove the Side Key.

INSTALLATION

Note the orientation of the Side Key to be installed and the pockets (a) and guiding pins (b) where to fit.



1222-6716 Rev 3


Replacement: Side Key

Place the Side Key inside its corresponding pockets.

Push to secure its position by using the tweezers.


1222-6716 Rev 3

Replacement

4.22 Camera Key




REMOVAL

Push the Side Key from outside until the key becomes released with the tweezers.

Remove the Camera Key.

INSTALLATION

Note the orientation of the Camera Key to be installed and the pockets (a) and guiding pins (b) where to fit.



1222-6716 Rev 3


Replacement: Camera Key

Place the Camera Key inside its corresponding pockets.

Push to secure its position by using the tweezers.


1222-6716 Rev 3

Replacement

4.23 Core Unit Label




REMOVAL

Read the old Core Unit Label and/or write the information into the ‘LabelMake’ program before removal.

Carefully remove the Core Unit Label by using the tweezers.

INSTALLATION

Check that the proper label format is loaded in the Zebra printer and write a new label by using the ‘LabelMake’ software.

The Core Unit Label has to be positioned inside the ‘golden’ frame as indicated by the pointers.

Place the new Core Unit Label inside the ‘golden’ frame as shown in the picture.

One label only is allowed!



1222-6716 Rev 3

Replacement

4.24 System Connector Cover




REMOVAL

Insert the Front Opening Tool underneath the System Connector Cover and pull upwards to release and remove it.

INSTALLATION

Attach a new System Connector Cover in place.

Note the orientation of the System Connector Cover.




1222-6716 Rev 3

Replacement

4.25 Grill Speaker Bottom




REMOVAL

Unsnap the hook by using the Front Opening Tool.

Unsnap these two hooks by using the Front Opening Tool.

Remove the Grill Speaker Bottom.



1222-6716 Rev 3


Replacement: Grill Speaker Bottom

INSTALLATION

Install this end of Grill Speaker Bottom to the hook.



1222-6716 Rev 3

Replacement

4.26 Net Speaker Bottom






REMOVAL

Detach the Net Speaker Bottom by using the Front Opening Tool.

Peel off the Net Speaker Bottom.

INSTALLATION

Attach a new Net Speaker Bottom in position.



1222-6716 Rev 3

Replacement: Net Speaker Bottom


Peel off the protection film.



1222-6716 Rev 3


Replacement

4.27 Grill Speaker Top




REMOVAL

Unsnap the hook by using the Front Opening Tool.

Remove the Grill Speaker Top.

INSTALLATION

Install this end of Grill Speaker top to the hook.


1222-6716 Rev 3

Replacement: Grill Speaker Top




1222-6716 Rev 3

Replacement

4.28 Net Speaker Top






REMOVAL

Detach this part of Net Speaker Top by using the Front Opening Tool.

Peel off the Net Speaker Top.

Detach this part of the Net Speaker Top by using the Front Opening Tool.



1222-6716 Rev 3


Replacement: Net Speaker Top

Peel off the Net Speaker Top.

INSTALLATION

Attach a new Net Speaker Top in position.




1222-6716 Rev 3

Replacement

4.29 Liquid Intrusion Indicator

INSPECTION

To check whether the Liquid Intrusion Indicator has been activated (reddish color), just remove the Battery Cover.

If activated:




REMOVAL

Push the Liquid Intrusion Indicator through the hole to release it with the tweezers.

Remove the Liquid Intrusion Indicator.

INSTALLATION

Attach a new Liquid Intrusion Indicator in position.



1222-6716 Rev 3

Replacement

4.30 Audio Jack




REMOVAL

Push the Audio Jack through the hole to release it with the tweezers.

Remove the Audio Jack.

INSTALLATION

Follow the 4.31 Removal and Installation instructions!

Place a new Audio Jack in position.



1222-6716 Rev 3

Replacement: Audio Jack




1222-6716 Rev 3


Replacement

4.31 Foil Adhesive Audio Jack






REMOVAL

Use the Front Opening Tool to remove the Foil Adhesive Audio Jack.

INSTALLATION

Attach a new Foil Adhesive Audio Jack in position as shown in the picture.



1222-6716 Rev 3

Replacement: Foil Adhesive Audio Jack




1222-6716 Rev 3

Replacement

4.32 Window Flash




REMOVAL

Push the Window Flash from back to detach it by using the tweezers.

Remove the Window Flash.

INSTALLATION

Attach a new Window Flash in position.

Note the orientation of the Window Flash.



1222-6716 Rev 3


Replacement: Window Flash



1222-6716 Rev 3

Replacement

4.33 Window Main Camera




REMOVAL

Push the Window Main Camera from back to detach it by using the tweezers.

Remove the Window Main Camera.

INSTALLATION

Attach a new Window Main Camera in position.



1222-6716 Rev 3

Replacement: Window Main Camera




1222-6716 Rev 3

Replacement

4.34 SIM Flex Assy

ITP SW AND FLASH LED CALIBRATION IS NEEDED IN THIS PROCEDURE! Refer to “Generic repair manual, electric” 1220-1336




REMOVAL

There are three snap hooks securing the SIM Flex Assy to the Carrier Holder SIM.

Release the SIM Flex Assy from the three hooks by using the Front Opening Tool.

Remove SIM Flex Assy.



1222-6716 Rev 3


Replacement: SIM Flex Assy

INSTALLATION

Install the SIM Flex Assy according to the guiding pins and holes.

Insert the SIM Flex Assy to the hook.

Press to secure the snap hooks.


1222-6716 Rev 3

Replacement

4.35 Gasket Flash




REMOVAL

Loosen and remove the Gasket Flash by using the Front Opening Tool.

INSTALLATION

Attach a new Gasket Flash in place.




1222-6716 Rev 3

Replacement

4.36 Cushion Cam B to B




REMOVAL

Loosen and remove the Cushion Cam B to B by using the Front Opening Tool.

INSTALLATION

Attach a new Cushion Cam B to B in place.




1222-6716 Rev 3

Replacement

4.37 MComp Sheet FPC Main




REMOVAL

Peel off the MComp Sheet FPC Main by using the tweezers.

INSTALLATION

Attach a new MComp Sheet FPC Main in place.




1222-6716 Rev 3

Replacement

4.38 Shield Can Lid AGPS




REMOVAL

Insert the dentist hook into the corners of the Shield Can Lid AGPS and pull upwards to release it.

Remove it.

INSTALLATION

Place a new Shield Can Lid AGPS on top of the shield fence.



1222-6716 Rev 3

Replacement: Shield Can Lid AGPS

Press gently until it is securely attached.



1222-6716 Rev 3


Replacement

4.39 Shield Can Lid WLAN




REMOVAL

Insert the dentist hook into the corners of the Shield Can Lid WLAN and pull upwards to release it.

Remove it.

INSTALLATION

Place a new Shield Can Lid WLAN on top of the shield fence.


1222-6716 Rev 3

Replacement: Shield Can Lid WLAN




1222-6716 Rev 3


Replacement

4.40 Shield Can Lid VERA


Follow the 4.37 Revomal instructions!




REMOVAL

Insert the dentist hook into the corners of the Shield Can Lid VERA and pull upwards to release it.

Remove it.

INSTALLATION

Place a new Shield Can Lid VERA on top of the shield fence.


1222-6716 Rev 3

Replacement: Shield Can Lid VERA




1222-6716 Rev 3


Replacement

4.41 Shield Can Lid KAJSA




REMOVAL

Insert the dentist hook into the corners of the Shield Can Lid KAJSA and pull upwards to release it.

Remove it.

INSTALLATION

Place a new Shield Can Lid KAJSA on top of the shield fence.


1222-6716 Rev 3

Replacement: Shield Can Lid KAJSA




1222-6716 Rev 3

Replacement

4.42 MComp Sheet MP202


Follow the 4.41 Revomal instructions!




REMOVAL

Carefully insert the dentist hook underneath the MComp Sheet MP202 and pull upwards to detach it.

Remove it.

INSTALLATION

Attach a new MComp Sheet MP202.



1222-6716 Rev 3

Replacement: MComp Sheet MP202




1222-6716 Rev 3


Replacement

4.43 Cushion 0.0 VT Cam

Follow the 3.1 – 3.2, 3.13 – 3.14 & 3.17 – 3.18 Disassembly instructions!


Follow the 5.1 – 5.2, 5.5 – 5.6 & 5.17 – 5.18 Reassembly instructions!

REMOVAL

Remove the Cushion 0.0 VT Cam by using the Front Opening Tool.

INSTALLATION

Attach a new Cushion 0.0 VT Cam in place.



1222-6716 Rev 3

Replacement

4.44 Light Guide

Follow the 3.1 – 3.2 & 3.13 – 3.14 Disassembly instructions!



REMOVAL

Detach the Light Guide by using dentist hook.

Peel off the Light Guide by using the Flex Film Assembly Tool

INSTALLATION

Attach a new Light Guide to the Navi Key PBA according to the guiding holes.



1222-6716 Rev 3

Replacement: Light Guide




1222-6716 Rev 3

Replacement

4.45 Cushion Upper PBA

Follow the 3.1 – 3.2 & 3.13 – 3.15 Disassembly instructions!



REMOVAL

Detach and remove the Cushion Upper PBA by using the tweezers.

INSTALLATION

Attach a new Cushion Upper PBA in position.




1222-6716 Rev 3

Replacement

4.46 Magnet

Follow the 3.1 – 3.2, 3.13 – 3.18 Disassembly instructions!



REMOVAL

Detach this part of Slider Flex Assy by using the Front Opening Tool.

Detach this part of Slider Flex Assy by using the Front Opening Tool.

Flip the Slider Flex Assy and hold it (1), carefully insert the dentist hook underneath the Magnet and remove it (2).



1222-6716 Rev 3

Replacement: Magnet

INSTALLATION

Note! Red stripe towards the top of the phone!

Place the new Magnet into its cavity by using the tweezers.


Flip the Slider Flex Assy back to its position in accordance with the guiding pins and holes.




1222-6716 Rev 3


Replacement

4.47 Slider Flex Assy




REMOVAL

Detach the Slider Flex Assy by using the Front Opening Tool.

Peel it off.

Turn the BtB connector in the direction of the arrow (1) to be able to make it pass through the slot and remove it (2).

Scrap! Flex Not to be reused!


1222-6716 Rev 3

Replacement: Slider Flex Assy

INSTALLATION

Lift up and hold the protection foil (1) and insert the BtB connector (2) through the slot as shown in the picture.

Continue to insert the Slider Flex Assy through the slot.

Attach this end of Slider Flex Assy according to the guiding pins and holes shown in the picture.




1222-6716 Rev 3


Replacement: Slider Flex Assy

Press this part of the Slider Flex Assy to secure the attachment.


1222-6716 Rev 3

5 Reassembly

The reassembly is done in the following order: 1. Camera – Front 2. Carrier Holder VT Cam 3. Display 4. Navi Key PBA 5. Navi Key (a) and Front Cover Assy (b) 6. Upper Screw Cap 7. Main PBA 8. Key Flex Assy 9. Main Antenna 10. Camera – Rear 11. Carrier Holder SIM and SIM Flex Assy

12. BT GPS Antenna 13. Lower Rear Cover 14. Lower Screw Cap 15. Panel Key Dummy 16. Keyboard 17. Battery 18. Battery Cover

5.1 Camera – Front Close the slider.

Place the Camera in its position.



1222-6716 Rev 3

Reassembly

Press to connect the Camera connector.

5.2 Carrier Holder VT Cam Place the Carrier Holder VT Cam on top of the Camera – Front.

Note the orientation of the Carrier Holder VT Cam.


Do not touch the camera lens.

5.3 Display Hold the Display and insert it at the top as indicated by the pointers.



1222-6716 Rev 3

Reassembly

Press the Display down into its proper position.

5.4 Navi Key PBA Hold the Navi Key PBA as shown in picture.

Connect these two connectors (1) and (2) by using fingers.

Carefully align the connectors before pressing! The connectors are sensitive and can easily be deformed!

Turn the Navi Key PBA back to its horizontal position and insert it into the two hooks.



1222-6716 Rev 3


Reassembly

Tighten the new screw (M1.4 x 1.6 silver) using the JCIS No.0 bit to a torque of 10 Ncm.

5.5 Navi Key and Front Cover Assy

Place the Navi Key in the cavity of the Front Cover Assy.

Note the orientation of the Navi Key.

Press to secure its position.

Place the Hinge Slider Assy on top of the Front Cover Assy.


1222-6716 Rev 3

Reassembly

Press around the Hinge Slider Assy until the two units snap together without any gaps.

Open the slider.

Tighten the four new screws (M1.4 x 1.6) using the JCIS No.0 bit to a torque of 10 Ncm.

5.6 Upper Screw Cap Attach a new Upper Screw Cap on top of one of the screws.

Use new Upper Screw Caps.



1222-6716 Rev 3

Reassembly


Do the same on top of the second screw cap.

5.7 Main PBA Place the Main PBA next to the Hinge Slider Assy as shown in the picture.

Connect the connector and press to secure the connection by using finger.

Carefully align the connector before pressing! The connector is sensitive and can easily be deformed!



1222-6716 Rev 3

Reassembly

Hold the Main PBA and insert it at the top as indicated by the pointers.

Press the Main PBA to secure it to the Hinge Slider Assy.

5.8 Key Flex Assy Hold the Key Flex Assy like this.

Use new Key Flex Assy.

Press to connect the BtB connector.

Carefully align the connector before pressing! The connector is sensitive and can easily be deformed!



1222-6716 Rev 3

Reassembly

Insert the Key Flex Assy into the slot as indicated by the pointer.

Attach this part of the Key Flex Assy to the Hinge Slider Assy according to the guiding pins and holes.


Careful when bending the flex over the edge, wrong handling could cause cracks in components on flex

Attach the Key Flex Assy and verify that the two holes are properly aligned with the pins on the Hinge Slider Assy.



1222-6716 Rev 3

Reassembly

Press the Key Flex Assy to secure the attachment.

Attach this part of the Key Flex Assy to the Hinge Slider Assy according to the guiding pin and hole and press to secure the attachment.

5.9 Main Antenna Hold the Main Antenna and hook one end of the Main Antenna to the Main PBA.

Press the other end of the Main Antenna to snap the hook to the Main PBA.



1222-6716 Rev 3

Reassembly

5.10 Camera – Rear Hold the Camera and connect its connector to the Main PBA by using finger.

Place the Camera in its position.

Do not touch the camera lens.

5.11 Carrier Holder SIM and SIM Flex Assy

Hold the Carrier Holder SIM like this.

Connect the BtB connector to the Main PBA by using finger.



1222-6716 Rev 3

Reassembly

Turn the Carrier Holder SIM and SIM Flex Assy to the horizontal position.


5.12 BT GPS Antenna Place the BT GPS Antenna on top of the Main PBA in its proper position.

Press to secure its snap hooks.



1222-6716 Rev 3

Reassembly

Tighten the two new screws (M1.4 x 2.7) using the JCIS No.0 bit to a torque of 10 Ncm.

5.13 Lower Rear Cover Hold the Lower Rear Cover like this.

Insert the Audio Jack into the hole on top the Lower Rear Cover as indicated by the pointer.

Press like this to snap this side of the Lower Rear Cover.



1222-6716 Rev 3

Reassembly

Do the same on the opposite side.

Tighten the two screws (M1.7 x 4.5) using the torx bit no. 6 to a torque of 18 Ncm.

5.14 Lower Screw Cap Attach a Lower Screw Cap on top of one of the screws.

Press to make it properly attached.



1222-6716 Rev 3

Reassembly

Do the same with the second Lower Screw Cap.

5.15 Panel Key Dummy Turn the phone over.

Hold the Panel Key Dummy and insert the two tabs to the phone as indicated by the pointers.

Press to secure the position.

Tighten the two screws (M1.7 x 4.5) using the torx bit no. 6 to a torque of 18 Ncm.



1222-6716 Rev 3

Reassembly

5.16 Keyboard Attach a new Keyboard in cavity by using the tweezers.

Press the Keyboard to secure the attachment.

Close the slider.

5.17 Battery Clean the system connector by using the ESD brush before installing the Battery.

Turn the phone over.

Insert the Battery at the top.


working instructions - amazon web servicesifixit-documents.s3.amazonaws.com/g4gas5ycnlig6apv.pdf ·...

Documents