winfoil cmds

8/10/2019 winfoil CMDS

1/16

S/No command used for description

1 know bsc status

2 know dip status for all bsc

3 To find dcps

4 to check Confoguration of particular site.

5 How to find dcps to check configuration for particular site

5 for TRX Addition in cell

5a

5b

5c

5d

5e

5f5g

5h

5i

5j

5k

6 for TRX Deletion in cell

6a

6b

6c

6d

6e

6f

6g

6h

6i

6j

6k

7 to find TX,TRX- Internal Alarm

8 to find cf- Internal Alarm

9 to check status of whole cabinet

For Reset the site

10 to block the cabinet or site, for reloading

11 making cabinet or site Out-Of-service

12 making CF(DXU) in-service


2/16

13 De-Blocking CF(DXU)

14 making cabinet or site in-service

15 De-Blocking cabinet or site

16 to find TG attached to cell

17 to find device on which cf(DXU) is loaded

18 to find SNT on TRC end off which E1 is part of

to find stm details

17 to find dip name

18 to find state of dip

19 to block the TRU, for reloading

20 making TRU Out-Of-service

21 making TRU in-service

22 De-Blocking TRU

23 to find which TRX is assosiated to which Cell

24 to find which TX is assosiated to which Cell

25 to find status of each unit;TS,TRX,TX

26 TO KNOW THE DIP FROM TG

27

28

29

30 TO KNOW THE SITE BELONG TO DIP

31

32

33

34

35 TO KNOW NEBOR CELL

36 command knows DIP fault supervision parameters.

37 for Antenna Hopping off (for 2A:47 cf alarm)

38 for Antenna Hopping on

39 to reset bsc for ROMT

to reset bsc for ROMT

40 dip name change command


3/16

41 commands to find stm location

42 it will give position for particular stm suppose for stm21 E1551 where rp=2

43 to check errors in a dip

44 to reset the dip command-1

45 to reset the dip command-2

46 to de-block the Dip command-1

47 to de-block the Dip command-2

48 for de-attachment of device for particular tg

49 for attachment of device for particular tg

50 to check TRX blockages for whole bsc

51 procedures for rectification

51a If local mode Hardware is present OR Not if present do rectification,if not present delete t

51b if OML fault communication between tru/Dxu

say fault 2a:0 replaced unit 21 using Fault Decoder

52 to check CF alrms for whole bsc

52a suppose fault 2A:57 use fault decoder

53 Check before Making Any dip MBL, check wheather Device are attached with some site

53a

53b

53c

53d

53e

53f

53h


4/16

54 Now the make dip MBL

54a

54b

54c

54d

TO CHECK POWER FOR PARTICULAR SITE

55 IT IS PRINT COMMAND)

TO CHANGE POWER)IT SHOULD BE 47 IN CASE OF 2204

TO CHECH HALTED SITES

56 PRINT COMMAND

56A TO HALT PARTICULAR SITE

56B TO UNHALT SITE

TO CHECK BSC EXTERNAL ALARMS

57 BSC EXTERNAL ALARMS

58

59 to find new tg.69 we file were commands are saved

70 to exicute command,

71 if IS fail

how to make DT to halt sites

72 in winfoil give command

a then copy all sites and paste them in excel sheet

b in excel sheet press together and continously

c press next , next and finsh

d copy only cell names and paste them in the centre

sothat we can write commands in front and back colmn

of cell names

e write command in excel in ist colmn before cellname colmn

f write command in excel in ist colmn after cellname colmn

g go to winfoil and then go

i after file go to

j copy all the data from excel and paste here and save

k press

73 to find device on which cf(DXU) is loaded

74 For GPRS Addition in a cell


5/16

75 LOOP TEST FAILED IN TIMESLOT

a Block TS

b Loop Test on TS

c Deblock TS

76 Check MPWR on TRU & BSPWRB/BSPWRT on associated Cell using command

a BSPWRB & BSPWRT must be less than or equal to MPWR on TX

77 TS IN UNUSED/SELECT STATE

a Check NUMREQBPC settings on CHGR 0 & 1 using command

bc

d

**** add gprs per sector

78 TS SYNC FAULT

Check Abis path DCP mapping.

Devices should be defined on correct DCPs w.r.t the Port A,B,C or D at RBS side.

If 2-DIPs are given & 1-DIP needs to be cascaded between two cabinets, then always

define both DIPs to Master cabinet & then cascade one of them with another cabinet.

In case of MBC site there should not be mismatch in devices and DCPs

i.e., fault will occur if 900 Mhz band devices attach on 1800 Mhz band devices.

a // Check ABIS print & find wrong device

b // Find wrong Device associated with TS

c // Block the TS

d // Out of Service TS

e // Remove the device

f // Check ABIS print

g // Check Alarm Status

79 to check the status of STM at vc level

80 for Antenna hoping off state

81 to check the MOIA


6/16

82 to find java version in laptop

83 to stop anti virus from cmd command

84 To check clock of particular site

85 to check taotal etms working in particular BSC

86 TO CHECK BTS SOFTWARE OF BTS (SAY 2964V2)

87 DURING TRX BLOCKAGE AND FAULTS (WHAT IS THE FAULT EXACTLY)

USE BTS FAULT DECODER TO FIND THE EXACT PROBLEM)

88 net meeting directly from run

89 To create Log files automatically in winfoil

90 To know which is master bts and slave bts


7/16

command

rlcrp:cell=all;

dtstp:dip=all,state=abl;

rxapp:mo=rxotg-value.

RXCDP:mo=rxotg-tgno;

rxmop:mo=rxotrx-113-0&&-11;

RXMOI:MO=RXOTRX-113-2,TEI=2,DCP1=134,DCP2=135&&142;

RXMOC:MO=RXOTRX-113-2,SIG=CONC,CELL=BTP590A;

RXMOI:MO=RXOTX-113-2,BAND=GSM900,MPWR=47;

RXMOC:MO=RXOTX-113-2,CELL=BTP590A;

RXMOI:MO=RXORX-113-2,BAND=GSM900,RXD=AB;

RXMOI:MO=RXOTS-113-2-0&&-7;

RXMOI:MO=RXOTRX-113-3,TEI=3,DCP1=143,DCP2=144&&145;RXMOC:MO=RXOTRX-113-3,SIG=CONC,CELL=BTP590A;

RXMOI:MO=RXOTX-113-3,BAND=GSM900,MPWR=47;

RXMOC:MO=RXOTX-113-3,CELL=RWP647a;

RXMOI:MO=RXORX-113-3,BAND=GSM900,RXD=AB;

RXMOI:MO=RXOTS-113-3-0&&-7;

rxbli:mo=rxotrx-310-10,subord;

rxese:mo=rxotrx-310-10,subord;

rxmoe:mo=rxots-310-10-0&&-7;

rxmoe:mo=rxotx-310-10;

rxmoe:mo=rxorx-310-10;

rxmoe:mo=rxotrx-310-10;

rxbli:mo=rxotrx-310-11,subord;


rxmoe:mo=rxots-310-11-0&&-7;

rxmoe:mo=rxotx-310-11;

rxmoe:mo=rxorx-310-11;

rxmoe:mo=rxotrx-310-11;

rxmfp:mo=rxotx-119-0;

rxmfp:mo=rxocf-119;

rxmsp:mo=rxocf-119,subord;

rxbli:mo=rxocf-119,subord,force;

rxese:mo=rxocf-119,subord;

rxesi:mo=rxocf-119;

Winfoil commands


8/16

rxble:mo=rxocf-119;

rxesi:mo=rxocf-119,subord;

rxble:mo=rxocf-119,subord;

rxtcp:moty=rxotg,cell=srr071a;

rxmdp:mo=rxocf-(tg no.);

radep:dev=rblt(2)-24;

tpcop:snt=etm2-7;

ntcop:snt=snt.no;

dtstp:dip=dip name;

rxbli:mo=rxotrx-119-0,subord,force;


rxesi:mo=rxotrx-119-0,subord;

rxble:mo=rxotrx-119-0,subord;


rxmop:mo=rxotx-119-0&&-11;

rxcdp:mo=rxotg-119;

RXAPP:MO=RXOTG-82;

RADEP:DEV=RBLT-1500;

NTCOP:SNT=all;(or)NTCOP:SNT=ETM2-4;

DTQUP:DIP=RBLT46;

DTDIP:DIP=;

NTCOP:SNT=;

STDEP:DEV=;

RXMDP:MOTY=RXOTG,DEV=;

RXTCP:MO=RXOTG-;

RLNCP:CELL=ALL;

DTFSP:DIP=ALL;

rxmsc:mo=rxocf-(tg no.),Ahop=off;

rxmsc:mo=rxocf-(tg no.),Ahop=on;

rxoce:connid=2;

rxoci:connid=2,bport=12002,passwd =romt123,access=apg;

dtpnc:dip=old dip.name,newdip=new dip name;


9/16

exemp:em=all,rp=all; (will show all regional processors)

expopirp=2; (say to given from msc side)

dtqup:dip=dip name;

dtqsr:dip=dip name,es,ses,sf;

DTQSR:DIP=DIP name,DEGR,UNACC;

tpble:sdip=3etm2,lp=vc12-(say1);

dtble:dip=dip name;

rxbli:mo=rxotg-43,subord,force;

rxese:mo=rxotg-43,subord;

blodi:dev=RBLT2-1745&&-1759;

exdae:dev=RBLT2-1745&&-1759;

rxape:mo=rxotg-43,dcp=29&&31;



rxapi:mo=rxotg-43,dev=RBLT2-1693&&-1695,dcp=29&&31 ;

exdai:dev=RBLT2-1693&&-1695;

blode:dev=RBLT2-1693&&-1695;

rxesi:mo=rxotg-43,subord;

rxble:mo=rxotg-43,subord;

rxasp:moty=rxotg;

rx using command no-4

rxmfp:mo=rxotrx-(say-89)-2;

rxasp:moty=rxocf;

rxmfp:mo=rxocf-41say;

R not

a:-dtdip:dip=say104rbl2;

say etm2-9,dip=41rbl2(which we r getting by using above command)

b:- ntcop:snt=etm2-9;

say RALT2-16160&&-16191

c:- to check wheather devices attached OR Not command below

rxapp:moty=rxotg;

find by using control+f commad (find RALT2-16167)If no attached with the site


10/16

blodi:dev=ralt2-16160-&&16191;

exade:dev=ralt2-288&&16191;

dtbli:dip=say104rbl2;

stdep:dev=ralt2-16160-&&-16191;

if you see SEBU don't touch

RLCPP:CELL=SRR075A;(SAY)

RLCPC:CELLSRR075A,BSPWRB=47,BSPWRT=47;

rlstp:cell=all,state=halted;

RLSTC:CELL=SRR075A,STATE=HALTED;

RLSTC:CELL=SRR075A,STATE=ACTIVE;

ALLIP:ALCAT=EXT;

rxmsp:moty=rxotg;((see which is last and add new one)f7

f4

rxbli:mo=rxois-tg-is no;

rlcrp:cell=all;

alt DEE(cells wil be seperated)

rlstc:cell=

,state=halted;

file

new

f4(dt will run)

rxmdp:mo=rxocf-(tg no.);



blodi:dev=RBLT2-1745&&-1759;

exdae:dev=RBLT2-1745&&-1759;

rxape:mo=rxotg-43,dcp=29&&31;

rxapi:mo=rxotg-43,dev=RBLT2-1693&&-1695,dcp=29&&31,res64k ;


11/16

exdai:dev=RBLT2-1693&&-1695;

blode:dev=RBLT2-1693&&-1695;

rxesi:mo=rxotg-43,subord;

rxble:mo=rxotg-43,subord;

An automatic loop test of the traffic carrying capabilities has failed.

RXBLI:MO=RXOTS---;

RXLTI:MO=RXOTS---;

RXBLE:MO=RXOTS---;

RXMOP:MO=RXOTX--;

RLCPP:CELL=;

RLBDP:CELL=;

For CHGR 0, NUMREQBPC=8For CHGR 1, NUMREQBPC=8*(no. of TRUs in CHGR1)

OR NUMREQBPC=SYSDEF for both CHGR 0 & 1

rlbdc:cell=nak239a,numreqegprsbpc=1,chgr=0;

RXAPP:MO=RXOTG-;

RXMDP:MO=RXOTS---;

RXBLI:MO=RXOTS---;

RXESE:MO=RXOTS---;

RXAPE:MO=RXOTG-,DCP=;

RXAPP:MO=RXOTG-;

RXASP:MO=RXOTG-;

tpstp:sdip=5etm2;

rlchc:cell=srr023c,hop=off,chgr=0;

rlchc:cell=srr023c,hop=off,chgr=1;

rlchc:cell=srr023c,hop=on,chgr=0;

rlchp:cell=srr322a;


12/16

start

run

cmd

cd\\

cd..

java -version(it must be above 1.5 version )all antivirus should be stoped

cmd;

start - stop;

nsdap;

pwnsp:sdip=all;

RXMOP:MO=RXOTG-(1)SAY

RXELP:MO=RXOTRX-(20-2SAY);

conf

aploc;

rxmop:mo=rxotf-tg


13/16


14/16

dtqup:dip=50AVTPR;

DTStp:dip=all,state=abl;

moshell 10.28.219.20

amos USRR183

lh ru fui get vswr

get local

viiget radio

inv

lst eternet

ALLIP:ALCAT=EXT;

rxcDP:mo=rxotg-84;

rlcrp:cell=srr213a;


rxtcp:moty=rxotg,cell=srr013b;

rxtcp:moty=rxotg,cell=srr013c;

rlcrp:cell=srr013c;

rlcrp:cell=srr013b;

rlcrp:cell=srr013a;

dtStp:dip=srr415;

rxmfp:mo=rxocf-46;

rxasp:mo=rxotg-42;

rxasp:mo=rxocf-42;





rxmsp:mo=rxocf-56,subord;dtStp:dip=srr445 ;


rxbli:mo=rxocf-107,subord,force;

rxble:mo=rxocf-107,subord,force;

rlcrp:cell=srr415a;

rlcr ;

rxmfp:mo=rxocf-84;

rxmfp:mo=rxocf-107-2;

rxmfp:mo=rxocf-107;

rxbli:mo=rxotrx-107-2,subord,force;

rxble:mo=rxotrx-107-2,subord,force;






rxmfp:mo=rxocf-749;

rxmfp:mo=rxocf-142;



15/16





rxmop:mo=rxotrx-32-&&-11;


rxmsp:mo=rxocf-107,subord;rxmfp:mo=rxocf-503;

rlcrp:cell=srr377a;

rlcrp:cell=srr377b;

rlcrp:cell=srr377c;

tStp:dip=all,state=abl;

alLIP:ALCAT=EXT;

dtStp:dip=tgp;

dtStp:dip=tgp407;

rlcrp:cell=tgp407a;

rlcrp:cell=tgp407b;

rlcrp:cell=tgp407c;

dtStp:dip=srr587t;

aircel@123


rlcrp:cell=srr587c;

rlcrp:cell=srr587b;

rlcrp:cell=srr587a;

rlcrp:cell=all;


dtStp:dip=srr701;

rlcrp:cell=srr701a;rlcrp:cell=srr701b;

dtStp:dip=srr360;

eaw SRIBSC5

rlcrp:cell=srr360;

rlcrp:cell=srr360a;




rxcDP:mo=rxotg-107;

rxcDP:mo=rxotg-83;

rxmsp:mo=rxotrx-83-0&-11;

rxmop:mo=rxotrx-83-0&-11;

rxmop:mo=rxotrx-107-0&-11;

rxasp:moty=rxocf;

emuzdar

rxasp:moty=rxoctg;

rxasp:moty=rxotg;

eaw SRIBSC4

amos 10.28.219.52


16/16

amos 10.28.219.20

str

eaw SRIBSC2

eaw SRIBSC3

dtStp:dip=all,state=abl;

winfoil cmds

Documents