whirlpool steam washer presented by: rick kuemin, msa training director brought to you by:
TRANSCRIPT
WHIRLPOOL STEAM
WASHER
Presented by: Rick Kuemin, MSA Training Presented by: Rick Kuemin, MSA Training DirectorDirectorwww.msaworld.comwww.msaworld.com
Brought to you by:
Safety First
Questions or comments? Please e-mail [email protected]
Model/Serial Designations
Model/Serial Number Tag
Questions or comments? Please e-mail [email protected]
Tech Sheet Location
Questions or comments? Please e-mail [email protected]
Top View (top panel removed)
Front & Rear View(panels removed)
Dispenser Drawer Removal
Questions or comments? Please e-mail [email protected]
Top Removal
Console Removal1
Console Views
Central Control Unit (CCU) Removal
CCU Tab and Slot Locations
Questions or comments? Please e-mail [email protected]
CCU Plug Locations
Water Valve Removal
Pressure Switch Removal
Line Filter Removal
Power Supply Cord Removal
Detergent Dispenser Removal1
Detergent Dispenser Removal/Reassembly 2
Detergent Dispenser Motor Removal
Door Switch Removal
Front Panel Removal
Bellows Removal/Reassembly
Drain Pump Removal/Reassembly
Eco Valve Removal/Reassembly
Vent and Fan Removal
Temperature Sensor and Heater Removal
Motor Control Unit Removal
Motor Removal
Stator Removal
Questions or comments? Please e-mail [email protected]
Tub Removal1
Tub Removal 2
Tub Removal3
Whirlpool Control Panel
Maytag User Interface Board
Home Diagnostics Screen
Service Abbreviation Diagnostic Mode
Enter Diagnostic Mode
Exit Diagnostic Mode
Test Menu Table
Questions or comments? Please e-mail [email protected]
Unsuccessful Activation
User Interface Test
Quick Diagnostic Test
Quick Test Chart
Software Version Display
Clear Fault/Error Codes
Questions or comments? Please e-mail [email protected]
Advancing Through Saved Fault/Error Codes
Exiting the Service Test
Questions or comments? Please e-mail [email protected]
Test Procedure
Questions or comments? Please e-mail [email protected]
Test 1: Cycle Control UnitPower Check 1
Test 1: Cycle Control UnitPower Check 2
Control Board Check
Questions or comments? Please e-mail [email protected]
Interference Filter
Questions or comments? Please e-mail [email protected]
Test 2: User Interface (UI)1
Test 3: Motor Circuit 1
Test 3: Motor Check 2
Test 4: Door Lock System1
Test 5: Drum Light (Steam Models)
Test 6: Water Inlet Valve1
Test 7: Pressure Sensor/Switch1
Test 7: Pressure Sensor/Switch2
Test 7: Pressure Sensor/Switch3
Test 8: Drain Pump1
Test 9: Flow Meter (Steam Model) 1
Test 10: Heating Element
Test 11: Temperature Sensor1
Test 11: Temperature Sensor2
Test 12: Dispenser1
Test 12: Dispenser2
Manually Unlocking the Door Lock System
Questions or comments? Please e-mail [email protected]
Fault/Error Code Explanation
Fault/Error Code Display Method Fault codes are displayed by alternately showing F# and E#. All fault codes have
an F# and an E#. The F# indicates the
suspect System/Category. The E# indicates the suspect Component system.
Fault/Error Codes1
Fault/Error Codes2
Fault/Error Codes3
Fault/Error Codes4
Fault/Error Codes5
Fault/Error Codes6
Diagnostics-Troubleshooting 1
Diagnostics-Troubleshooting 2
Diagnostics-Troubleshooting3
Diagnostics-Troubleshooting 4
Troubleshooting
Troubleshooting
Questions or comments? Please e-mail [email protected]
Troubleshooting
Troubleshooting
Troubleshooting
Troubleshooting
Troubleshooting
Troubleshooting
Troubleshooting
Questions or comments? Please e-mail [email protected]
Troubleshooting
Troubleshooting
Strip Circuit-Dispenser Motor/Switch
Strip Circuit-Door Lock System
Strip Circuit-Heater/Temperature Sensor
Strip Circuit-Wash Motor (3 phase)
Strip Circuit-Pressure Sensor
That is all!Thank You