Práctica que ejemplifique el uso del protocolo EIGRP.

Topología resuelta

Comandos de configuración para cada ruteador retomando los nuevos conocimientos adquiridos durante la semana.i. Nombre ii. Contraseñasiii. Interfacesiv. Tablas de enrutamientov. Respaldo de la configuración

AMAPOLA

Router>enableRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname AmapolaAmapola(config)#interface fa0/0Amapola(config-if)#ip address 140.0.2.1 255.255.254.0Amapola(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Amapola(config-if)#exitAmapola(config)#interface se0/0Amapola(config-if)#ip address 140.0.0.5 255.255.255.252Amapola(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0, changed state to downAmapola(config-if)#clock rate 56000Amapola(config-if)#exitAmapola(config)#interface se0/1Amapola(config-if)#ip address 140.0.0.2 255.255.255.252Amapola(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/1, changed state to downAmapola(config-if)#exitAmapola(config)#interface se0/2Amapola(config-if)#ip address 140.0.0.13 255.255.255.252Amapola(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/2, changed state to downAmapola(config-if)#clock rate 56000Amapola(config-if)#exitAmapola(config)#route eigrp 100Amapola(config-router)#network 140.0.2.0Amapola(config-router)#network 140.0.0.0Amapola(config-router)#network 140.0.0.12Amapola(config-router)#network 140.0.0.4Amapola(config-router)#exitAmapola(config)#enable secret classAmapola(config)#enable password ciscoAmapola(config)#line console 0Amapola(config-line)#password ciscoAmapola(config-line)#loginAmapola(config-line)#exitAmapola(config)#line vty 0 4Amapola(config-line)#password ciscoAmapola(config-line)#loginAmapola(config-line)#exitAmapola(config)#exitAmapola#

%SYS-5-CONFIG_I: Configured from console by console

Amapola#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Amapola#^ZAmapola#exit

Amapola con0 is now available

Press RETURN to get started.

User Access Verification

Password:

Amapola>enablePassword: Amapola#sh runBuilding configuration...

Current configuration : 768 bytes!version 12.2no service timestamps log datetimemsecno service timestamps debug datetimemsecno service password-encryption!hostnameAmapola!!!enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1enable password cisco!!!interface FastEthernet0/0ip address 140.0.2.1 255.255.254.0duplex autospeed auto!interface Serial0/0ip address 140.0.0.5 255.255.255.252clock rate 56000!interface Serial0/1ip address 140.0.0.2 255.255.255.252!interface Serial0/2ip address 140.0.0.13 255.255.255.252clock rate 56000!interface Serial0/3

noip addressshutdown!routereigrp 100network 140.0.0.0auto-summary!ip classless!line con 0password ciscologinlinevty 0 4password ciscologin!!!end

Amapola#

Oro

Router>enableRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname OroOro(config)#interface fa0/0Oro(config-if)#ip add 140.0.0.17 255.255.255.240Oro(config-if)#no shutdown

Oro(config-if)#%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Oro(config-if)#interface s0/0Oro(config-if)#ip add 140.0.0.1 255.255.255.252Oro(config-if)#no shutdown

Oro(config-if)#%LINK-5-CHANGED: Interface Serial0/0, changed state to up

Oro(config-if)#clock rate 56000Oro(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

Oro(config-if)#exitOro(config)#interface s0/1Oro(config-if)#ip add 140.0.0.10 255.255.255.252Oro(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/1, changed state to up

Oro(config-if)#Oro(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up

Oro(config-if)#route eigrp 100Oro(config-router)#network 140.0.0.16Oro(config-router)#network 140.0.0.8Oro(config-router)#network 140.0.0.0Oro(config-router)#exitOro(config)#enable secret classOro(config)#enable password ciscoOro(config)#line console 0Oro(config-line)#password ciscoOro(config-line)#loginOro(config-line)#exitOro(config)#line vty 0 4Oro(config-line)#password ciscoOro(config-line)#loginOro(config-line)#exitOro(config)#exitOro#%SYS-5-CONFIG_I: Configured from console by console

Oro#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Oro#sh runBuilding configuration...

Current configuration : 658 bytes!version 12.2no service timestamps log datetimemsecno service timestamps debug datetimemsecno service password-encryption!hostname Oro!!!enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1enable password cisco!interface FastEthernet0/0ip address 140.0.0.17 255.255.255.240duplex autospeed auto!interface Serial0/0ip address 140.0.0.1 255.255.255.252clock rate 56000!

interface Serial0/1ip address 140.0.0.10 255.255.255.252!routereigrp 10network 140.0.0.0auto-summary!ip classless!nocdp run!line con 0password ciscologinlinevty 0 4password ciscologin!end

Oro#exit

Oro con0 is now available

Press RETURN to get started.

User Access Verification

Password:

Oro>enablePassword: Oro#

PLATA

Router>enableRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname PlataPlata(config)#interface fa 0/0

Plata(config-if)#ip add 140.0.0.33 255.255.255.240Plata(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Plata(config-if)#exitPlata(config)#interface s0/0

Plata(config-if)#ip add 140.0.0.9 255.255.255.252Plata(config-if)#clock rate 56000Plata (config-if) #no shutdown

%LINK-5-CHANGED: Interface Serial0/0, changed state to downPlata(config-if)#exitPlata(config)#interface se0/1Plata(config-if)#ip add 140.0.0.6 255.255.255.252Plata(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/1, changed state to up

Plata(config-if)#exitPlata(config)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up

Plata(config)#route eigrp 100Plata(config-router)#network 140.0.0.4Plata(config-router)#%DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 140.0.0.5 (Serial0/1) is up: new adjacencyPlata(config-router)#network 140.0.0.8Plata(config-router)#network 140.0.0.32Plata(config-router)#exitPlata(config)#enable secret classPlata(config)#enable password ciscoPlata(config)#line console 0Plata(config-line)#password ciscoPlata(config-line)#loginPlata(config-line)#exitPlata(config)#line vty 0 4Plata(config-line)#password ciscoPlata(config-line)#loginPlata(config-line)#exitPlata(config)#^ZPlata#%SYS-5-CONFIG_I: Configured from console by console

Amapola#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]

Plata#^ZPlata#exit

Amapola con0 is now available

Press RETURN to get started.

User Access Verification

Password:

Plata>enablePassword:

Amapola#sh run Building configuration...

Current configuration : 658 bytes!version 12.2no service timestamps log datetimemsecno service timestamps debug datetimemsecno service password-encryption!hostname Plata!!enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1enable password cisco!!interface FastEthernet0/0ip address 140.0.0.33 255.255.255.240duplex autospeed auto!interface Serial0/0ip address 140.0.0.9 255.255.255.252clock rate 56000!interface Serial0/1ip address 140.0.0.6 255.255.255.252!routereigrp 100network 140.0.0.0auto-summary!ip classless!!nocdp run!!line con 0password ciscologinlinevty 0 4password ciscologin!!End

Plata#

Cobre

Router>enableRouter #config t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname CobreCobre(config)#interface fa0/0Cobre(config-if)#ip add 140.0.0.254 255.255.255.128Cobre(config-if)#no shutdown

Cobre(config-if)#%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up%IP-4-DUPADDR: Duplicate address 140.0.0.254 on FastEthernet0/0, sourced by 00D0.BC58.C4E8

Cobre(config-if)#exitCobre(config)#interface se0/1Cobre(config-if)#ip add 140.0.0.14 255.255.255.252Cobre(config-if)#no shutdown

Cobre(config-if)#%LINK-5-CHANGED: Interface Serial0/1, changed state to up

Cobre(config-if)#exitCobre(config)#e%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to upCobre(config)#routeeigrp 500Cobre(config-Cobre)#network 140.0.0.128Cobre(config-Cobre)#network 140.0.0.12Cobre(config-Cobre)#exitCobre(config)#enablesecretclassCobre(config)#enablepassword ciscoCobre(config)#line console 0Cobre(config-line)#password ciscoCobre(config-line)#loginCobre(config-line)#exitCobre(config)#line vty 0 4Cobre(config-line)#password ciscoCobre(config-line)#loginCobre(config-line)#exitCobre(config)#exitCobre#%SYS-5-CONFIG_I: Configured from console by console

Cobre#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Cobre#exitCobre con0 is now available

Press RETURN to get started.

User Access Verification

Password:

Cobre>enablePassword: Cobre#sh runBuilding configuration...

Current configuration : 629 bytes!version 12.2no service timestamps log datetimemsecno service timestamps debug datetimemsecno service password-encryption!hostnameCobre!!!enable secret 5 $1$mERr$9cTjUIEqNGurQiFU.ZeCi1enable password cisco!!interface FastEthernet0/0ip address 140.0.0.254 255.255.255.128duplex autospeed auto!interface Serial0/0noip addressshutdown!interface Serial0/1ip address 140.0.0.14 255.255.255.252!Cobreeigrp 500network 140.0.0.0auto-summary!ip classless!nocdp run!line con 0password ciscologinlinevty 0 4password ciscologin!!end

Cobre#

Pruebas de conectividad (ping). De un servidor a otro.

Pruebas de conectividad (telnet).

Ping

Ping

Comando de verificación