wall ties formwork
TRANSCRIPT
-
7/28/2019 Wall Ties Formwork
1/96
Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Why Consider WTF? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Standard and Specialty Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-32Standard Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-21
8-8 / 8-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6-12 Double Bracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Super Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13International Housing Forms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Radius Forms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Bricks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17Gang Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-19Big Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Corner Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-25Standard Corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23Specialty Corners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-25
Brickledge Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Stoops. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Pilaster Forms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Round Column Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Wall Barrier Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Square Adjustable Column Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Jump Fillers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Offset Endbar Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Control Joint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Chamfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Laydown Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29Deck Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Deck Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Monolithic Slab Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Stemwall Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Products and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-66Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67-90
Foundation Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68-69Crawl Space Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-71Precast Forms Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72-73Agricultural Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74-75Concrete Step Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76-77Fence Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Post & Beam Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79Swimming Pool & Spa Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-81Concrete Housing Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82-84Safe Room/Security Room Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85International Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86-89Burial Chamber Forms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Credit Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1 - 9 2 1
-
7/28/2019 Wall Ties Formwork
2/96www.wallties.com
2
QUALITY ASSURANCE AND UNPARALLELED SERVICE
Quality control extends beyond our manufacturing plant. We are actively engaged in custom design and engineeringto improve our product line. We constantly re-evaluate our products, and regularly consult with contractors, builders, anddistributors. We also conduct on-site training and inspections to ensure our clients' success.
Listening to your needs and providing solutions has been the hallmark of our business since day one. We design products
that meet your requirements and demands, not ours. Special applications and custom design are a challenge, not a problem.That's why we lead the industry in developing solutions through new designs.
Beautiful FaceWhat attracted meto these concreteforms is the inset facesheet. It gives theforms strength to
keep from bending atthe corner. Yet theygive you a beautifulface.They are light enough that one mancan carry a 3' x 9' concrete form so Ineed fewer people to unload, set andstrip. Weve discovered we can have allthree sides of an impossible triangle -good, fast and profitable.
---Larry Swearingin, Lawson, MO
Quality
WorkmanshipOver the last 30years I have purchasedand used concreteforms from severaldifferent manufacturers.All aspects of theWall-Ties & Formsforming equipment, from manufacture toon-the-job use, is superior to any otherconcrete forming system I have used.
---Curt Fields, Raleigh-Durham,NC
InnovationIn over 30 years inthe concrete equip-ment supply businessit is my experiencethat WTF is the most
innovative companyin the concrete formindustry. Their abilityand willingness to designaround customerneeds is second to none.
---John Hess, Belleville, IL
Consider the qualityIt's the impression you leave
Wall-Ties & Forms, Inc. manufactures products in over a 100,000 sq. ft. facility located in Bonner Springs, KS.WTF utilizes advanced robotics, fiber optics, and the latest in computer technology to produce the best quality productat a competitive price.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
3/96www.wallties.com
WHY CONSIDER WTF CONCRETE FORMS?
Simplicity
Simple Tie, Pin, and Wedgesystem is used to set theconcrete forms. This allowsunskilled labor to be quicklytrained in the use of theequipment. (see page #34).Also available is the WTFAttached Pin (see page #36).
SpeedThe system is fast. It is notuncommon for a contractor todouble or triple the output of theirconcrete form crews when theyconvert from a wood faced formsystem to WTF forms.
Faster production, cost efficiency,
and more attractive walls causedTom Schreivogel and his son-in-law,Brian Hladik, to abandon woodforms for concrete forms. Thehandwriting was on the wall,says Schreivogel.
3WHY CONSIDER WTF?
LABOR SAVINGS
Lightweight AluminumThe concrete forms are made of lightweight aluminum which allows the largest components to be hand carried.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
4/96www.wallties.com
4
LONG LIFE OF CONCRETE FORMS
OUR DESIGNS REVOLUTIONIZED THE INDUSTRY!
WTF is committed to engineering and manufacturing the best, strongest, most durable concrete forming systems available inthe marketplace. The key to our success and your satisfaction is our strict adherence to a basic business principle:Products are designed and built to fit your needs.
Minimal MaintenanceWith minimal maintenance, it is not unusualfor a contractor to get 1,000, 2,000 or as manyas 3,000 uses with the WTF concrete form.
Face Sheet Protection Weld Life
Bushing Strength Bracing Construction
LongevityThe increased longevity of ourforms was accomplished by examining theweaknesses of other form systems and making themour strengths. WTF founders repaired many forms anddiscovered four common weaknesses. We then designed our forms toimprove or solve those weaknesses. When looking at concrete form systems,there are four areas to evaluate before making your form purchase decision:
LONG LIFE OF FORMS
The following several pages is a glimpse of how we took others' weaknesses and made them our strengths.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
5/96
5
www.wallties.com
Face sheet protection is a critical area in determining
life of the concrete form. Face sheet peel is a common
problem because many manufacturers simply overlap
the siderail with the face sheet. Over time the face sheet
with a thickness of .090 to .125 will pull away from the
siderail adversely affecting the concrete wall appearance
and ultimately decreasing form life.
WTF solved this problem by inventing the Inset Face
Sheet. Because the face sheet is inset, it is not only
protected by the siderail and endbar, but the weld is
also much closer to the face sheet edge. This innovation
provides for a much stronger concrete form.
FACE SHEET PROTECTION
FACE SHEET PROTECTION
FAC
ESHEETPEEL
WTF INSETMETHOD
~ Provides uniform wall appearance
~ Prevents damage and wear to edges
~ Ensures stronger bond with welds closer tothe edge of face sheet
WTF Total Perimeter Inset Method:
WELDS CLOSE TO EDGE OF FACE SHEET
THICKENED ENDBAR
Unique feature of WTF forms is the endbar designthat allows standard pin and wedge to tighten whenstacking concrete forms.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
6/96www.wallties.com
6
WELD LIFEWTF has extended the life of welds by using a state-of-the-art robotics welding system on full panels. These panelsreceive the most concrete placement pressure. A soft alloy weld wire is utilized in the weld process. This ensuresgreater flexibility without sacrificing strength when the concrete form is in use. This greatly reduces, if not eliminates,broken welds.
~ Robotics ensure qualityand consistency
~ Continuous welds aroundperimeter provide longerconcrete form life
~ Hand welds tested forquality assurance
WELD LIFE
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
7/96www.wallties.com
7
BUSHING STRENGTHBushings are a crucial area to take into consideration when purchasing concrete forms. The bushing protects the siderail pinholefrom wear and tear. Bushing failure is expensive to repair and will greatly reduce the life of an aluminum form. The WTF designhas been in place since 1979 and has not been changed, because it works under normal conditions.
Wall-Ties uses a 4" case hardened, plated and crowned steel bushing. The bushing is made of solid steel and is installed using" heavy duty rivets. We have the largest rivet used in the industry. Rivets are countersunk for ease of cleaning the siderail. Weguarantee our bushings to last as long as, or longer than, the form.
~ 4" steel bushing allows pressure to be distributed
~ Bushings contain medium carbon steel and are heat treated which increases tensile strengththus reducing "egg-shaping" the pinhole, cracking the siderail and ultimately siderail failure
~ " solid steel plated rivets to ensure a secure hold
WTF RIVETS~ " solid steel plated rivets ensure
long life of the bushing
~ Rivets are countersunk for ease ofsiderail cleaning
EXTRUDED ALUMINUM SIDERAILS~ Notched for inset face sheet~ Dual contact~ Easily cleaned
SHOE BUSHINGWTF utilizes a shoe bushing on allextruded fillers (12" and smaller).This feature is also available on alllarger panels by request. WTFemploys a roll over method of shoebushing placement.
Countersunk rivetsfor ease of siderailcleaning.
Crowned bushingmakes it easier totighten and loosenwedge since it onlycontacts in two places.
BUSHING STRENGTH
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
8/96www.wallties.com
8
BRACING CONSTRUCTIONBracing construction is extremely important to avoid weight gain through concrete accumulation under the horizontal brace.Concrete accumulation can occur when there is an open hat section. Weight gain shortens form life and increases the likelihood ofback injuries. By enclosing the hat section, WTF ensures no accumulation of concrete, subsequently, no weight gain. WTF bracesare serrated to simplify carrying and using of the concrete forms.
BOXED BRACE
~ 1 x 2 Tube Brace
~ Serrated for ease of use
~ Tube is fully enclosed
eliminating concrete
build-up
BRACING CONSTRUCTION
(Available in metric sizes.)
31/2"
5"
5" CHANNEL BRACE
~Aluminum tube to control deflection,"ridges" on bracing provide additionalstrength and dent resistance
~ Serrated for ease of use
~ 5" fully enclosed brace, eliminatesconcrete accumulation inside the brace
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
9/96www.wallties.com
TOTAL PERIMETER INSET FACE SHEET* Prevents damage and wear to face sheet edges.
* Superior weld penetration achieved by placing weld near the edge of the
face sheet.
* Increases overall strength and life of panel without leaving unsightly seams.
* Corner gussets added to reinforce corner.
BRACING* Boxed design makes it impossible for concrete to
enter and accumulate inside brace.
* Ends are welded on sides and tops to strengthen the
form and ensure concrete cannot enter brace.
* Extruded Braces are serrated to prevent slipping and
aid in handling, yet will not accumulate concrete.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Dual contact for ease of alignment.
* Notch for inset face sheet strengthens panel.
BUSHINGS* Heat-treated and plated bushings are held in place by
heavy duty inch solid steel plated rivets.* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it
like swedged bushings.
* Rivets are flush with siderail to reduce accumulation
of concrete and make cleaning easier.
WELDING* Continuous weld around concrete form, including over top of bracing.
* Full panels are welded with computerized Robot to ensure consistency and quality.
* Certified Quality Control Program.
THICKENED ENDBAR* Unique feature of WTF forms is the endbar design that allows standard pin and
wedge to tighten when stacking concrete forms.
7" spacing betweenhorizontal braces
8-8 / 8-24 CONCRETE FORMS
STANDARD AND SPECIALTY CONCRETE FORMS
(Available in metric sizes.)
This hole pattern makes the 8-8 / 8-24 idealin markets converting from block to pouredwalls. This allows the contractor to easilyaccomplish 8" jumps.
~ Widths from 36" - 1"
~ Heights up to 120"
~ Standard face sheet thickness .125
~ Also available in .115
~ Brace is 1 x 2 tube
~ 36" x 96", .125 thickness weighs 84#
~ 36" x 108", .125 thickness weighs 90#
9
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
10/96www.wallties.com
10
The 6/12 hole pattern allows the contractorto easily accomplish 12" jumps.
~ Available in widths from 36" - 1" andheights up to 120"
~ Standard face sheet thickness .125
~ Also available in .115
~ 36" x 96", .125 thickness weighs 93#
~ 36" x 108", .125 thickness weighs 102#
TOTAL PERIMETER INSET FACE SHEET* Prevents damage and wear to face sheet edges.
* Superior weld penetration achieved by placing weld near the edge of the
face sheet.
* Increases overall strength and life of panel without leaving unsightly seams.
* Corner gussets added to reinforce corner.
BRACING* 5" fully enclosed brace design makes it
impossible for concrete to enter and
accumulate inside brace.
* Ends are welded on sides and tops to
strengthen the form and ensure concrete
cannot enter brace.
* Extruded Braces are serrated to prevent
slipping and aid in handling, yet will
not accumulate concrete.
* Two convexed ridges on bracing provide
additional strength and dent resistance.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Dual point contact for ease of alignment.
* Notch for inset face sheet strengthens panel.
BUSHINGS* Heat-treated and plated bushings are held in place by heavy
duty inch solid steel plated rivets.* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it like swedged bushings.
* Rivets are countersunk into siderail to reduce accumulation of concrete and
make cleaning easier.
WELDING* Continuous weld around form, including over top of bracing.
* Full panels are welded with computerized Robot to ensure consistency and quality.
* Certified Quality Control Program.
THICKENED ENDBAR* Unique feature of WTF forms is the endbar design that allows standard pin and
wedge to tighten when stacking concrete forms.
6-12 CONCRETE FORMS
(Available in metric sizes.)
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
11/96www.wallties.com
11
TOTAL PERIMETER INSET FACE SHEET* Prevents damage and wear to face sheet edges.
* Superior weld penetration achieved by placing
weld near the edge of the face sheet.
* Increases overall strength and life of panel
without leaving unsightly seams.
* Corner gussets added to reinforce corner.
BRACING* Boxed design makes it impossible for
concrete to enter and accumulate inside brace.
* Ends are welded on sides and tops to strengthen
the form and ensure concrete cannot enter brace.
* Extruded Braces are serrated to prevent slipping and aid in handling, yet will not
accumulate concrete. Includes vertical brace.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Dual point contact for ease of alignment.
* Notch for inset face sheet strengthens panel.
BUSHINGS* Heat-treated and plated bushings are
held in place by heavy duty inchsolid steel plated rivets.
* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it like swedged bushings.
* Rivets are countersunk into siderail to reduce accumulation of concrete and make
cleaning easier.
WELDING* Continuous weld around form, including over top of bracing.
* Full panels are welded with computerized Robot to ensure consistency and quality.
* Certified Quality Control Program.
THICKENED ENDBAR* Unique feature of WTF forms is the endbar design that allows standard pin and
wedge to tighten when stacking concrete forms.
7" spacing betweenhorizontal braces
6-12 DOUBLE BRACING
CONCRETE FORMS
(Available in metric sizes.)
Every Panel is Built to Last
In addition to the 6-12 we offer 6-12Double Bracing. This upgrade isconstructed with a double 1 x 2 tubeproviding less weight, easier handling andmore nailing area. This concrete form
has the durability for any projectresidential or light commercial.
~ Widths from 36" - 1"~ Heights up to 120"~ 1 x 2 Tube Brace~ Standard face sheet thickness .125~ Also available in .115~ 36" x 96", .125 thickness weighs 91#~ 36" x 108", .125 thickness weighs 100#
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
12/96www.wallties.com
12
Is weight an issue with your concrete forms? The Super Light panel isthe form for you. Consistent care increases the longevity of this panel.
Available in:~ 36" x 120" weighs only 90#~ 36" x 108" weighs only 81#~ 36" x 96" weighs only 73#
TOTAL PERIMETERINSET FACE SHEET* Prevents damage and wear to face sheet edges.
* Superior weld penetration achieved by placing
weld near the edge of the face sheet.
* Increases overall strength and life of panel
without leaving unsightly seams.
* Corner gussets added to reinforce corner.
* Striker pads for protection of .094 face sheet.
BRACING* Ends are welded on sides and tops to strengthen
the form and ensure concrete cannot enter brace.
* Three convexed ridges on bracing provide additional strength and dent resistance.
* Backbone added for reduction in pillowcasing.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Dual point contact for ease of alignment.
* Notch for inset face sheet strengthens panel.
BUSHINGS* Heat-treated and plated bushings are held in place by heavy duty
inch solid steel plated rivets.* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it like swedged bushings.
* Rivets are countersunk into siderail to reduce accumulation of concrete and make
cleaning easier.
WELDING* Continuous weld around form, including over top of bracing.
* Certified Quality Control Program.
THICKENED ENDBAR* Unique feature of WTF forms is the endbar design that allows standard pin and
wedge to tighten when stacking concrete forms.
SUPER LIGHT CONCRETE FORMS
(Available in metric sizes.)
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
13/96www.wallties.com
13
Accurate, Reliable
Because this concrete form is engineered for minimal deflection and pillowcasing, it isideal for commercial applications requiring the flattest possible wall surface. This isaccomplished by manufacturing the form 24" wide with a .156 face sheet. This form isbuilt with the 8-8 or 6-12 hole pattern. The Commercial Form is used in the SecureTechBuilding System.
~ Width 24" ~ Heights up to 144" ~ 1 x 2 Tube Brace~ Face sheet .156 - thickest aluminum face sheet available in the industry
- also available with .125 face sheet~ 24" X 96" weighs 64# ~ 24" x 108" weighs 71#
(Available in metric sizes)
TOTAL PERIMETER INSET FACE SHEET* Prevents damage and wear to face sheet edges.
* Superior weld penetration achieved by placing weld near the edge of the face sheet.* Increases overall strength and life of panel without leaving unsightly seams.
* Corner gussets added to reinforce corner.
BRACING* Boxed design makes it impossible for concrete to
enter and accumulate inside brace.
* Ends are welded on sides and tops to strengthen the
form and ensure concrete cannot enter brace.
* Extruded Braces are serrated to prevent slipping and
aid in handling, yet will not accumulate concrete.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Dual point contact for ease of alignment.* Notch for inset face sheet strengthens panel.
BUSHINGS* Heat-treated and plated bushings are held in place by
heavy duty inch solid steel plated rivets.* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it like
swedged bushings.
* Rivets are countersunk into siderail to reduce accumulation
of concrete and make cleaning easier.
WELDING* Continuous weld around form, including over top of bracing.
* Full panels are welded with computerized Robot to ensure consistency and quality.* Certified Quality Control Program.
THICKENED ENDBAR* Unique feature of WTF forms is the endbar design that allows standard pin and
wedge to tighten when stacking concrete forms.
COMMERCIAL CONCRETE FORM
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
14/96www.wallties.com
14 INTERNATIONALHOUSING CONCRETE FORM
Having been involved in several international mass housing projects,
we know first-hand the fast and rigorous pace of these projects. Thisform is built with 20cm or 15-30cm hole patterns. Evolving fromthese experiences is the best concrete forming system available today.
~ Standard Width 60cm ~ Heights up to 300cm~ Face sheet 4mm - used on all standard wall panels~ 60cm x 2.40m weighs 29.1 kg ~ 60cm x 2.70m weighs 32.3 kg~ 25mm x 48mm Tube Brace
Special sizes and shapes available!
TOTAL PERIMETERINSET FACE SHEET* Prevents damage and wear to face sheet edges.
* Superior weld penetration achieved by placing
weld near the edge of the face sheet.
* Increases overall strength and life of panel
without leaving unsightly seams.
* Backbone added for reduction in pillowcasing.
* Corner gussets added to reinforce corner.
* 4mm aluminum face sheet.
BRACING* Ends are welded on sides and tops to strengthen the form and ensure concrete
cannot enter brace.
* Three convexed ridges on bracing provide additional strength.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Dual point contact for ease of alignment.
* Notch for inset face sheet strengthens panel.
* 20cm hole spacing.
BUSHINGS* Heat-treated and plated bushings are held in place by heavy duty
inch solid steel plated rivets.* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it like swedged bushings.
* Rivets are countersunk into siderail to reduce accumulation of concrete and make
cleaning easier.
WELDING* Continuous weld around form, including over
top of bracing.
* Certified Quality Control Program.
THICKENED ENDBAR* Unique feature of WTF forms is the endbardesign that allows standard pin and wedge totighten when stacking concrete forms.
Available with the stripping angle whenutilized with poured deck applications.The stripping angle is for ease ofconcrete form removal.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
15/96www.wallties.com
15RADIUS CONCRETE FORMS
Easily stacked to obtain desired wall height and can be
purchased in multiple piece corner sets. Available in
heights of 12", 24", 36" and 48".
A 90 turn with a 6", 24", 36", or 48" radius produces a more decorativeappearance than a standard 90 corner.
Our radius forms are also available in
smooth, textured and VertiBrick patterns.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
16/96www.wallties.com
16
SMOOTHSMOOTHTEXTUREDTEXTURED
VERVERTIBRICKTIBRICK
BRICK CONCRETE FORMS
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
17/96www.wallties.com
17
Designed For Those Who Want More Choices
Looks like brickFeels like brick WTFs natural brick-look concrete formsleave a lasting impression. Residential or commercial applications can easily bepainted or two-toned for a decorative look. Forms are compatible to pouring brickon one side and smooth on the other.
Smooth Brick, Textured Brick and VertiBrick
All our brick concrete forms give you a deep brick designproviding a realistic finished look.
~ Width 36" - 1"
~ Heights up to 108"
~ Available in any hole pattern6-128-88-24
~ VertiBrick is also available in metric sizes
BRACING* Boxed design makes it impossible for concrete to enter and accumulate
inside brace.
* Ends are welded on sides and tops to strengthen the form and ensure concrete
can not enter brace.
SIDERAIL* Heavy duty extruded aluminum extends life of panel.
* Exposed corners are mitered to reduce the accumulation of concrete.
BUSHINGS* Heat-treated and plated bushings are held in place by heavy duty inch solid steel
plated rivets.
* Crowned bushing allows for easy release of wedges.
* Bushings increase strength of siderail, not weaken it like swedged bushings.
* Rivets are countersunk into siderail to reduce accumulation of concrete and make
cleaning easier.
WELDING* Continuous weld around form, over top of bracing.
* Certified Quality Control Program.
SMOOTH BRICK
TEXTURED BRICK
VERTIBRICK
BRICK CONCRETE FORMS
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
18/96www.wallties.com
18
The WTF Gang Adapterallows contractors to easilygang concrete formstogether. The system canbe used for 8', 9' and 10'walls and requires onlytwo ties at the gangadapter.
~ 6" wide and less than 5 1/2" deep when fully assembled.~ Has a permanent waler built into the top and bottom of the system.~ Uses a tapered reusable cone with a rod tie.~ Available in Smooth, Smooth Brick, Textured Brick and VertiBrick.~ Attached wall braces, rod ties, and scaffold brackets are stored on the concrete form.~ Simple system assembly.~ 6-12 and 8-24 hole pattern included in the siderail to allow for use of fillers
and corners.~ Uses only 2 ties up to 10' tall. The ties are spaced on 42" intervals vertically.~ Dry tie available for top of form on 10' and taller walls.~ Weighs less than 7 lbs. per square foot fully assembled.
The Gang Adapter allows contractors to easilytransition to handset panels by using the standardpin and wedge.
The WTFGang Adapterenables acontractor to
create gangsutilizing36" wideconcrete forms.
GANG ADAPTER
Tie Spacing 42"
(Patent #6,523,323)
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
19/96www.wallties.com
19
An 8" bolt is used to attach the gangadapter to forms on both sides.
A 2" bolt is provided for attachmentof a single form at the end of the gang.
Assembly of the system is very simple, requiring few tools.The adapters are attached to the wall panels using locking nutsand bolts provided by WTF.
Scaffold bracketsattach easily andrequire no loosehardware.Various typesand sizes areavailable.
Once assembled the gang weighsless than 7 lbs. per square foot.
GANG ADAPTER
The Aligner Waler Angle - this piece is made to matchdesired gang lengths and is used to ensure the system isstraight. The Gang Adapter allows the Waler Angle to beplaced at the top and the bottom of the concrete form.
The permanent waler is built oflightweight aluminum and measures
3" x 3" x 1/2".
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
20/96www.wallties.com
20
Amazingly Large, Fast FormingJust as its name implies, these concrete forms arebuilt large. The WTF Big Panel is ideal for repetitivetall wall construction -
Available in:~ 8' x 8'~ 8' x 9'~ 8' x 10' plus various size fillers and corners
~ Face Sheet thickness of .156 to provide flat walls~ Weighs 7 lbs per square foot including all
accessories and bracing~ Panels are only 4 3/4" deep
BIG PANEL
Side Rail allows for the
attachment of WTF handset
forms using a standard Pin
and Wedge.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
21/96www.wallties.com
21BIG PANEL
~ Utilizes a one pieceoutside corner
~ Brace and accessoriesare stored on the form
~ Uses a tapered reusablecone with rod tie
~ AW Clamp is also aWaler piece
Agricultural project with 2" offset in wall.
Big Panels stackedto achieve a 16' wallon a commercialproject.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
22/96www.wallties.com
22
CORNER CONCRETE FORMS
STANDARD CORNERS ~ All corners available up to 144"
ISC 4 X 4 ISC 4 X 6
OUTSIDE CORNERS (OSC)
ONE-PIECE OSC OSC BRICK WITH ATTACHED ANGLE
6 x 6 and 8 x 8also available
Ideal whenwall thicknesschanges occurat the corner
When compared to using a W (see page #22) and twofillers, a 96" tall One-Piece OSC eliminates as many as18 pieces per corner.
Mitered to fit and givea true brick look.
Specify brick type
CORNER CONCRETE FORMS
Aluminumangle alsoavailable tocreate OSC withsmooth forms.
When compared to using a brick attachment, this methodeliminates as many as 9 pieces per corner.
INSIDE CORNERS (ISC)
~ All corners available in brick patterns~ Specify Nominal or Full
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
23/96www.wallties.com
23CORNER CONCRETE FORMS
Available in smooth and brick concrete forms
Sizes are 2", 3" and 4"
SPECIALTY CORNERS ~ All corners are available up to 144"~ Specify Nominal or Full
HINGED INSIDE CORNER (HISC) HINGED OUTSIDE CORNER (HOSC)
The OSC Attachment is used to build outside corners using fillers.
The HISC can beused across fromstandard fillersutilizing the 45angle clip (seepage #51) or the
HOSC to createan angledcorner for baywindowapplications.
Eliminates as many as 13 pieces per cornerwhen compared to using two fillers and
45 angle clips.
Different wall thicknesses areeasily achieved by utilizingdifferent size fillers for OSC.Change angles by adding fillers.
Different wall thicknesses are easilyachieved by utilizing different size
fillers or different size attachmentsto form an OSC.
Specifywallthickness
OSC ATTACHMENT (W)
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
24/96www.wallties.com
24 CORNER CONCRETE FORMS
ISC 4 X 4 w/WALL THICKNESSCHANGE OPTION
Face sheet holes allow ISC to beused for 2" wall thickness changes.
The offset ISC is oneof WTFs most versatile
corners, it can be used as astandard ISC or for various offsets
using different size fillers.
BRICK ADJUSTABLE OFFSET ISC
ADJUSTABLE OFFSET ISC
See also AdjustablePilaster Form (see page #27.)
Note: The Adjustable Offset is a one piece ISC. One pairrequired to accomplish offset.
OFFSET ISC
Flathead pin(see page #35)
ADJUSTABLE OFFSET ISC
The Adjustable Offset ISC is used for a variety of differentoffsets without the need for different sized fillers. Standardoffsets are 6"-14" on 2" increments.Also available in smooth and textured brick.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
25/96www.wallties.com
25
FIXED 45 ISC FIXED 45 OSC
Ideal when you consistently have 45 corners and do notneed the added flexibility provided by the HISC(see page #23).
Specify wall thickness -nominal or full
Also available in Fixed 30 for ISCand OSC.
CORNER CONCRETE FORMS
COLLAPSIBLE CORNER DIAGONAL ISC
The Collapsible ISC is ideal for core wallapplications. It works well with WTF GangAdapter, and Big Panel Systems.
The Diagonal ISC is designed to provide the chamferedcorner required in many box culverts and tunnels. Thisis also used in various LineredSwimming Pool applications.Available in custom sizes.
Gang Adapter (see page #18-19)Big Panel Systems (see page #20-21)
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
26/96www.wallties.com
26
BRICKLEDGE CONCRETE FORMS
Our aluminum brickledge forms are used when adding a brickledge around the outside of a foundation wall.
LUG BRACKETwith 1" OBROUND HOLE
Attaches to top of forms with pin and wedge,
aligner clamp, vise-grips or C clamp.Provides more opportunity to align
with holes at end rails due tothe slotted plates.
Also available with 4"to 10" plates
6"X 6" PLATE BRACKETwith 4" SLOT
Attaches to top of forms with pin
and wedge, aligner clamp,vise-grips or C clamp.
Specify depth
DENVER BRICKLEDGE FORMS
Available in heights up to 48"
SLIPOVER BRICKLEDGE FORMS
Aluminum slipover brickledge forms are used to create varioussized brickledgefillers. Used inconjunction withPlate or Lug BracketBrickledge.
Brickledge over 17" in depth hasa nailer area provided for simple attachment to the concrete form.This eliminates creeling problems.
Specify depth
BRICKLEDGE CONCRETE FORMS
Just as its name implies,this was originallydesigned for the Denver
area. Its perfect forallowing adjustment to
your brickledge depth.
Available insizes up to24" wide
GREEN BAY BRICKLEDGE FORMS
Simply rest on top of tie and securewith aluminum ledge clamp.
Rest on tie
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
27/96www.wallties.com
27
STOOP SET
Used to create supportfor porches and airconditioner pads.
Standard projectionsavailable:
22" and 46 "
PILASTER FORMS
Stoop set includes 2 arms and 2 stoop bottoms.
Specify hole pattern, projection and overallheight.
ASSORTED CONCRETE FORMS
ADJUSTABLE PILASTER FORMS
Used for long wall applications to create additional
strength in the concrete wall. Specify hole pattern and
pilaster height, width and depth.
FIXED PILASTER FORMS
Allows for various pilastersizes utilizing different
size fillers.
Also available inbrick.
(See alsoAdjustable
Offset ISCCornerpage #24)
Pin holes allow end of wallapplications.
ASSORTED CONCRETE FORMS
Full height pilaster.
Tapered pilaster.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
28/96www.wallties.com
The WTF Round Column Forms are easilystackable to achieve various columnheights and nest for simplicity oftransportation.
Available in heights from 12" to 120"
Larger sizes available upon request.
Diameter sizes available:10", 12", 14", 16", 18", 20", 22", 24"
28 ASSORTED CONCRETE FORMS
ROUND COLUMN FORMS
SQUARE ADJUSTABLE COLUMN FORMS
WALL BARRIER FORMS
LARGE COLUMN FORMS
Wall Barrier Forms built tocontractor specifications.
The Wall Barrier Formsuse Breakback Ties.(see page #40)
Large Column Forms built to contractor specifications, whilethe maximum height is 48" the forms are easily stacked tocreate the desired height.
Forms forHollowColumnapplicationsalsoavailable. Available in smooth
or brick textured, upto 144" in height.
Achieves multiple widths, for both square or rectangular columns.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
29/96
29
www.wallties.com
ASSORTED CONCRETE FORMS
ALUMINUM CONTROL JOINT
Attaches tothe WTF formwith pins.
ALUMINUM CHAMFER STRIP
Attaches to the WTF form with flathead pinsto create a3/4" x 3/4"chamfer for topof walls andsquare columns.
Specify holepattern.
OFFSET ENDBAR PANEL
Commonly used in confinementsystems (see page #74).
JUMP FILLERS
These fillersare built withholes on 1" or2" centers toallow a
contractor toeasilyachievedifferentelevationchanges.
Standard sizesof jump filler:
6"8"
10"12"
Other sizesavailable.
Specify holepattern.
The WTF 36 x 48 Laydown Panelallows a contractor to lay
the form eitherdirection. This
form is notdesigned to beput on thebottom ofstackedforms.
In addition
WTFmanufacturesforms with tieslots to allowfor laydownapplications.
LAYDOWN FORMS
WTF has perfected several methods for laydown application utilizing standardforms (see page #47).
Also available with a 4" offset for brickledgeapplications.
Createsa tapered1 1/2" x 1"control jointwithin wall.
Specify holepattern.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
30/96www.wallties.com
30 DECK
STANDARD LEDGER CROWN MOLD LEDGER
STEEL HEAD/BEAM SUPPORT
BEAM BAR
BEAM
DROP HEAD BEAM /DROP HEADJACK POST
Patent #6,513,785
*Both Ledgers utilizes deck slide clamp for attachment.
(see page #52)
DECK COMPONENTS
The crown moldledger provides adecorative crownmolding in concrete.
Available in 8" x 4"size.
The ledger handles the transition from wall to deck.Available in 6" x 4" or 8" x 4". Also available indifferent lengths.
LEDGER
DECK PANELS
DROP HEAD DECK BEAM ASSEMBLY
To accommodateoverhead usage,deck panels arebuilt with the
.115 face sheet toreduce weight,with attachedhardware for easeof installation.
The siderail has asmall miter whichallows for ease instripping.
Deck PanelBracket
Jack post comesequipped withadjustable screw.
Accepts 4 x 4 aluminumbeam or wood for
additional decksupport.
Also available in standardfull, nominal.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
31/96www.wallties.com
31
DECK ASSEMBLY
The Deck Assembly is designed for the most efficient cycling of the forming system once
structure achieves minimum design strength.
The drop head, beam bars, and beams areassembled using standard pins and wedges.
Deck beam fully assembled. The jack posts are put into place.
The Drop Head Deck Beam Assembly is then liftedand put into the desired location.
The first deck panel is connected to the deck beamassembly and ledger utilizing the deck slide clamp.
This process is continued until all deck panels are in place.
Once the concrete is placed and at minimum requiredstrength, the deck beam assembly and deck panels can bedisassembled, leaving the drop head in place for therequired time.
Deck Slide Clamp(see page #52)
DECK
An adjustable screw isprovided to allow for anyadjustments needed in the deck.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
32/96www.wallties.com
32 MONOLITHIC SLAB FORMS
MONOLITHIC SLAB FORMS
Wooden Stakes
1/2" to 15/16" Steel Stakes
Rebar
Adjustable clamps for use withThe versatile concrete slab form is madeof lightweight high strength aluminum.This allows for a long lasting, easilyportable form that is simple to assemble.In slab uses, a simple windmill method isused to create outside corners. Inside andoutside corner forms are available for
more complex slab applications as wellas footing uses. Also available in brickpatterns.
Adjustable Camlock
MONOLITHIC SLAB/STEMWALL FORMS
Available in lengths up to 12' and heights of4", 6", 8", 10", or 12".
Commonly used:1. In areas of slab construction with high water tables.2. Slabs with garage elevation changes.3. When stemwalls are used for tunnel form alignment.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
33/96
33
www.wallties.com
Wall-Ties & Forms, Inc. always recommends that when using or installing our products that all OSHA guidelines and
regulations be followed and that our products be used exclusively for their specifically intended purposes and uses.
Concrete Forms Products and AccessoriesTable of Contents
Products and Accessories ............................................................................................................ 33-66
Standard Pin and Wedges ................................. 34 Special Application Hardware ...............51-52Standard Pin ................................ 34 Angle Clips .......................... 51
Straight Wedge ............................ 34 Aluminum Cap Clip ............ 51Curved Wedge ............................. 34 Cap/Filler Bracket ............... 51Specialty Pins .................................................... 35 Saddle Bracket ..................... 51
Flathead Pin ................................. 35 Brickledge Bar ..................... 51Filler Pins ..................................... 35 Continuous Brickledge Bar...52Pax Pin ......................................... 35 Deck Slide Clamp ............... 52Curved Pin ................................... 35 Window Clamp ................... 52
Attached Hardware ........................................... 36 Plywood Adapter ................. 52Long Away Pin ............................ 36 Parapet Bracket ................... 52Short Away Pin ............................ 36 Aligner Clamps.................... 52Short Against Pin ......................... 36 Essential Extras ..................................... 53-54
Waler Brackets ................................................... 37-39 Wall Aligner ........................ 53Steel Walers .................................. 37 Aluminum Wall Brace.......... 53
Adjustable Steel Waler .................. 37 Hand Punch......................... 53Locking Waler with Pin ................ 3 8 Wall Puller .......................... 53Vertical Stiffener ........................... 38 Form & Corner Puller ........ 53
Aluminum Waler ........................... 38 String Line Attachment ...... 53Vertical Waler ................................ 38 Siderail Puller ...................... 53
Aluminum Waler Board ................ 39 Turn Buckles ....................... 53Scfld Brkt/Waler Combo ............. 39 Wire Ties ............................ 54
Standard Wall Ties ............................................ 40-45 Tie Breaker Bar.................... 54Two Hole Ties ............................... 40 Rod Support ........................ 54Three Hole Ties ............................ 40 Tie Twister .......................... 54Four Hole Comb. T ies .................. 40 Bolts .................................... 54Round End Ties ............................ 40 Hurricane Strap .................. 54Breakback Ties .............................. 40 Slide Hammer ..................... 54
Tie Placement Charts ................... 41-45 Pouring Accessories .............................. 55-56Specialty Wall Ties ............................................ 46 5 Gal. Spray Tanks................ 55
Reusable Alum. Bar Ties ............... 46 60 Gal. S pray Tanks ............ 55Reusable Wall Ties .........................46 Footing Chute ..................... 55Concrete Housing Ties ................. 46 Pouring Boards .................... 55
Laydown Applications ....................................... 47 Pouring Shovel .....................56Flat Steel U-Ties ........................... 47 Concrete Chutes ................. 56
Wire Base Ties .............................. 47 Aluminum Puddle Stick ..... 56Base Tie Pin (Silver Bullet) ........... 47 Release Agents ...................................... 57Flathead Pin .................................. 47 Material Handling Equipment ............. 58-59
Blockouts ........................................................... 48-49 Full Panel Baskets ............... 58Beam Blocks .................................. 48 Filler Baskets ....................... 59
45 Degree Beam Block .................. 48 WTF Insulation ..................................... 60-61Pier Block-Out............................... 48 Insulation Tie....................... 60Drain Tile Block-Out.................... 48 Foam ................................ ... 60Egress Step Block-Out.................. 49 F-Section ............................. 60
Blockdowns ....................................................... 49-50 I-Section ............................. 60Steel Blockdowns ...........................49-50 T-Section ............................ 60
Aluminum Blockdowns ................. 49 Dampproofing and Waterproofing ........62-63Adjustable Blockdowns ..................50 Deco 20 ............................... 62-63Blockoffs ........................................50 Platon .................................. 63
Windows .............................................. 64-66
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
34/96
34
www.wallties.com
CONCRETE FORMS PRODUCTS & ACCESSORIES
STANDARD PIN AND WEDGES
We offer a wide variety of pins and wedges designed to increase efficiency no matter what application.
STANDARD PIN
Our round, tapered pins have a milled wedge slot.The shank is designed to eliminate pin sag and
improve ease of stripping. Pins are made fromsteel and are heat-treated for long life.
250/bucket
Product #SPI10000000000
~Typical connection with pin and straight wedge~
STRAIGHT
Wedges are used withpins to tightenadjoining forms.Securing the tie andform in place.
250/bagProduct
#SWE10000000000
CURVED
Curved wedges have the samefunction as straight wedgesbut the curved shape allowsfor easy insertion and lessrisk of damage to faceof form.
250/bag
Product#SWE20000000000
WEDGES
1 2
43
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
35/96www.wallties.com
35CONCRETE FORMS PRODUCTS & ACCESSORIES
SPECIALTY PINS
FLATHEAD PIN
The flathead pin is used when pinning througha single rail or when placing concrete againstan existing wall. Also used in laydownapplications, such as 36" x 96" panel, to pour
a 36" tall concrete wall. (See laydownapplication on page #47 for specific example.)
Product #SPI20000000000
COMBINATION FILLER PIN WITH HEAD
This pin passes completelythrough 2" aluminum fillersand connects adjoiningpanels with a wedge. Toconvert to either 1" or 1"filler simply insert duplexnail in the appropriate hole.
Combination with head -1", 1", 2"
Product #SPI01152000000
PAX PIN
Pax pin is slightly longer than our standard pin. Used with paxforms and special applications.
Product #SPI30000000000
STRAIGHT FILLER PIN
These pins pass through appropriate size fillers and areconnected to adjoining panels with wedges.
Straight filler pins
Product #1" ~ SPI010000000002" ~ SPI020000000003" ~ SPI030000000004" ~ SPI040000000006" ~ SPI06000000000
CURVED PIN
The curved pin is used in special corner and radiusapplications.
Product #SPI40000000000
For smooth wallapplications. Brickapplication requiresfiller or ISC atlocation.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
36/96
36 CONCRETE FORMS
PRODUCTS & ACCESSORIES
ATTACHED HARDWARE
Factory installed permanent pin system.When forms are outfitted with attached hardware, wedging is only required at top and bottom pin.
LONG AWAY
Available for panels 36" - 16" wide
Product #SPI50000000000
SHORT AWAY
Short away pins are used on all holes except top andbottom holes on 36" - 16" widepanels. Can be retracted andloose pins used.
Product
#SPI51000000000
SHORT AGAINST
The short against pin is popular among con-tractors using 9' forms. Pins are attached atthe top hole where tie placement is notnecessary for alignment. Shortagainst pins are also used onfillers 15" - 10" wide. These pinscannot be retracted in order to useloose pins. Product #SPI52000000000
Available on 36" to
10" fillers, however,most contractorstypically have itinstalled on 36"wide forms only.
Long away pins are used on top and bottom pinholes ofform where rod must pass through vertical braces. Can beretracted and loose pins used.
On 108" forms, most contractors do notutilize the top hole for a tie, therefore,many choose to place an attached pin,aiding in alignment by simply engagingthe pin.
-
7/28/2019 Wall Ties Formwork
37/96
37
www.wallties.com
CONCRETE FORMS PRODUCTS & ACCESSORIES
WALER BRACKETS
WTF steel waler brackets can be used with standard wood boards or aluminum waler board. Brackets attach directly to theforms to straighten the wall and minimize the need for additional bracing. In most residential construction,
one row of walers at the top of the wall is usually sufficient.
STANDARD STEEL WALER COMBINATION STEEL WALER
Standard waler brackets are top notch to provide a fast andefficient attachment directly to the form panel. Used withsmooth aluminum, smooth brick, and VertiBrick forms.
Available in:2" x 3" ~ Product
#SWA23000000000
2" x 4" ~ Product#SWA24000000000
2" x 6" ~ Product#SWA26000000000
2" x 8" ~ Product#SWA28000000000
Combination waler bracket features combination holes. To beused with textured brick or smooth forms.
Available in:2" x 3" ~ Product
#SWA23000000090
2" x 4" ~ Product
#SWA24000000090
2" x 6" ~ Product
#SWA26000000090
2" x 8" ~ Product
#SWA28000000090
~Removal of waler board~~Tightening of waler board~
Wall Braceattachment hole
Wall Braceattachment hole
Wall Braceattachment hole
WTF Aluminum Waler Board(see page #39)
ADJUSTABLE STEEL WALER BRACKETWTF adjustable waler bracket is one of our newest innovations.
Adjustable steel waler bracket is designed to usewith the WTF aluminum waler board. May also beused with 2" x 4" or 2" x 6" lumber.
Available in:2 x 4 ~ Product #SWA020400000002 x 6 ~ Product #SWA02060000000
Overlap 24" at waler joint toensure proper alignment.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
38/96
38
www.wallties.com
CONCRETE FORMS PRODUCTS & ACCESSORIES
LOCKING WALER WITH PIN
The locking feature on this waler bracket ensures a goodconnection. The pin is attached with a flange that overlaps bothsiderails. No loose hardware!
Available in:2" x 3" ~ Product
#SWA230000000992" x 4" ~ Product#SWA240000000992" x 6" ~ Product#SWA26000000099
ALUMINUM WALER
Aluminum waler brackets are designed to be used with a three holetie at the top of the wall. Simply insert overthe three hole tie. This bracket does notrequire loose pins or wedges.
Available in:
2" x 4" ~ Product#AWA240000000002" x 6" ~ Product#AWA26000000000
Note: When utilized with the WTF tie, stripping is accomplished bystriking downward with a 2" x 4" from the top of the wall.
VERTICAL WALER
When stacking forms, vertical waling may be necessary to preventcreeling. This bracket is used in conjunction with 2" x 4" lumber. Itis used on the side opposite of the waler bracket. Savestime when stacking by eliminating the need to
stagger or stack short and tall forms.
Product #SWA10000000000
Note: 2" x 4" lumber is used on both sides of bracket
VERTICAL STIFFENER
Used in much the same manner as the vertical waler.Vertical stiffeners are faster than vertical walers becausethere is no lumber required. Used on opposite side ofthe wall from walers. Saves time when stacking by
eliminating the need to stagger or stack short andtall forms.
Specify hole pattern:6/12 ~ Product #AWA100000000108/8 ~ Product #AWA10000000020
Not to beused in tie
location.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
39/96www.wallties.com
39CONCRETE FORMS PRODUCTS & ACCESSORIES
ALUMINUM WALER BOARD SCAFFOLD BRACKET WALER COMBINATION
While the traditional waler board is madeof wood, the aluminum waler board isbeing used more and more because of theconsistent dimensions and long life itprovides. Can be used in place of 2" x 4"or 2" x 6" lumber.
Lengths: 150" ~ Product #AWA35000001200300" ~ Product #AWA35000002400
SCAFFOLD BRACKET
Our standard scaffold easily attaches to thetop of form providing a walkway for additionalsafety. Standard section receives two 2" x 10"pieces of lumber along with a 2" x 4" or 2" x 6"waler board.
Other sizes available upon request.
Specify size of waler board:
2" x 4" ~ Product #SBK002400028002" x 6" ~ Product #SBK00260002800
Note: Kicker board attaches to the base ofscaffold bracket.
SCAFFOLD BRACKETWITH POST
Wall-Ties scaffold and post canaccommodate a safety rail around thewall. A 2" x 4" slips into post holderand is attached with two nails. Easilyattaches to the top of form providinga stable platform for yourself and
your crew.2" x 4" ~ Product
#SBK002400028902" x 6" ~ Product
#SBK00260002890
(See page #37)
Also used inFootingForm
Application.
Note:This can be used with most walerbrackets. However, the aluminumwaler board was designed withthe adjustable steel waler bracketin mind.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
40/96
40
www.wallties.com
CONCRETE FORMS PRODUCTS & ACCESSORIES
STANDARD WALL TIES
WTF ties are manufactured to meet the requirements of today'svarious pouring methods. They are made of cold rolled steel. Wecontinually perform quality control testing to ensure that all of ourties yield a minimum pull strength of 7,200#.
TWO HOLE
Single Rod Notch (SRN)
4" Single Notch only 6" Single or Double Notch8", 9", 10", 12" Available in Single, Double or Triple NotchSpecify Nominal or FullUnlimited tie length available
THREE HOLE
Three Hole Tie: Used at top of form with thealuminum waler brackets
4" - 6" Single Notch only 6" - 8" Single or Double Notch8" - 10" Available in Single, Double or Triple Notch
Specify Nominal or Full
Additional sizes - Single orDouble Notch only
Pin ONLY at shortestlength (ex: DO NOT USEan 8" - 10" tie as a 10" tie)
FOUR HOLE COMBINATION TIESMulti-dimensional ties are used when changing wall thickness.We recommend use of 50% more four hole ties in seam than would
normally be used.
Single Rod Notch - any length Specify Nominal or Full
Ties available in metric sizes
ROUND END TIES
Available in 6" SRN, 8" TRN, 10" TRN
Specify Nominal or Full
BREAKBACK TIES
Breakback ties are vertical break ties designed to break back intothe wall at specified dimensions." - Standard Breakback Other depths availableAny length Specify Nominal or Full
Breaking ties is accomplished by striking downward with hammeror utilizing the WTF Tie Breaker Bar (see page #54).
Double Rod Notch (DRN)
Triple Rod Notch (TRN)
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
41/96
TIE PLACEMENT CHARTS 41
-
7/28/2019 Wall Ties Formwork
42/96
42 TIE PLACEMENT CHARTS
www.wallties.com
TIE PLACEMENT CHARTS
Conditions that affect lateral concrete pressure:
1. Height of the wall
2. Fill rate
3. Temperature
4. Type of concrete
(chemical additives)
6/12 HOLE PATTERN
5. Weight of concrete
6. Slump of concrete
7. Vibration of concrete
3 ft. Wide Forming System
NOTE: Wall-Ties & Forms recommends placing
cap form on the bottom for speed.
Tie Maximum Load - 7,200#
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
43/96
TIE PLACEMENT CHARTS 43
www.wallties.com
TIE PLACEMENT CHARTS
Tie Maximum Load - 7,200#
Be certain to meet all OSHA requirements including fill rate
**OSHA safety requirements will not be exceeded if:
1. Fill rate does not exceed 8'0"/hour.
2. Tie is used in every hole on walls over 8'0".
8/8 HOLE PATTERN
3 ft. Wide Forming System
NOTE: Wall-Ties & Forms recommends placing
cap form on the bottom for speed.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
44/96
44 TIE PLACEMENT CHARTS
www.wallties.com
6/12 HOLE PATTERN
TIE PLACEMENT CHARTS
2 ft. Wide Forming System
Tie Maximum Load - 7,200#
Be certain to meet all OSHA requirements including fill rate
**OSHA safety requirements will not be exceeded if:
1. Fill rate does not exceed 8'0"/hour.
2. Tie is used in every hole on walls over 8'0".
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
45/96
TIE PLACEMENT CHARTS 45
www.wallties.com
TIE PLACEMENT CHARTS
8/8 HOLE PATTERN
2 ft. Wide Forming System
Tie Maximum Load - 7,200#
Be certain to meet all OSHA requirements including fill rate
**OSHA safety requirements will not be exceeded if:
1. Fill rate does not exceed 8'0"/hour.
2. Tie is used in every hole on walls over 8'0".
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
46/96www.wallties.com
46 CONCRETE FORMS PRODUCTS & ACCESSORIES
SPECIALTY WALL TIES
REUSABLE ALUMINUM BAR TIESReusable aluminum bar ties are used as bulkhead bars as well as top tiesfor laydown applications. May be used with the standard pinand wedge. These can be used as brickledge bars to nail wood-en brickledge to top of forms.
3/8" x 1 " x wall thickness to 12" Single or Combination
2" x 2" x 3/8" x wall thickness greater than 12"Specify Nominal or Full and Length
REUSABLE WALL TIESDesigned without rod notches and break-offs for ease of removalfrom a wall and reused. This is designed for markets with very lowlabor costs.
Maximum tie size is 8"
Specify Nominal or Full
(Available in metric sizes)
TIE SLEEVE
The tie sleeve is used with thereusable pull tie. This sleeve
allows for tie removal.
CONCRETE HOUSING TIES
INSULATION TIE
See page #60
The I-Section along with the insulation tie ensures that
insulation stays in place for concrete placement. Also
provides an additional attaching point.
Patent #5,987,830
This tie is used to incorporate foam insulation. Designed with a specific breaking
point for clean break off the insulation to eliminate thermal bleeding. It also has a
notch to hold the I-Section in place, which eliminates any foam notching which
is required in other insulating systems. Breakback is determined by thickness
of foam.
I-SECTION
Tie sleeves available from
WTF in various lengths.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
47/96
47
www.wallties.com
CONCRETE FORMS PRODUCTS & ACCESSORIES
For laydown applications ONLY!Base tie pins hold tie in place atthe base of the form.
Maximum wall height: 36"Maximum tie spacing: 24"
Product #API10000000000
LAYDOWN APPLICATIONS
WTF has many form designs that allow the form to be laid on its side. The 36x48 laydown (see page #29)has additional bracing to allow for this use. For customers with forms that are not designed to be laid on
their side WTF has perfected hardware for this application. We recommend the following guidelines.
FLAT STEEL U-TIE
For laydown applications ONLY! Not to be used in close trenchconditions wherestripping requirespulling top of formdown toward ground.No pins or wedgesrequired.
Maximum wall height: 36"Maximum tie spacing: 24"
Up to 36" ~ Specify Nominal or Full
WIRE BASE TIE
Wire base ties are used in laydown form applications. Drivewedges through raised loops tosecure base tie through rail.
Maximum wall height: 36"Maximum tie spacing: 24"
Up to 20" ~ Specify Nominal or Full
BASE TIE PIN (SILVER BULLET) FLATHEAD PIN
The flathead pin is used in laydownapplications with standard ties. Can also be used whenpouring a concrete wall against an existing structure(see page #35). This pin is the only design used in laydownapplications in walls over 36" tall.
Product #SPI20000000000
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
48/96www.wallties.com
48
BLOCKOUTS
BEAM BLOCKS
Heavyweight beam block ready to attach to your form witha simple C clamp. For use with a standard 8" deep I-beam.Other sizes available.
Order by height, width and front to back.
45 BEAM BLOCKSThe 45 degree blockout is used to create beam void for use ofbeams in bay areas.
Heavyweight beam block ready to attach to your form with asimple C clamp. For use with a standard 8" deep I-beam.Other sizes available.
DRAIN TILE BLOCKOUT PIER BLOCKOUT
Pier Blockout is placed on Pier Pad prior to slab pour.
Once concrete is poured andcured Blockout is removedfor installation of Pier.
Specify size and hole pattern.
Available in steel or aluminum
Drain Tile Blockout allows
ease of installation ofDrain Tile.
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
49/96
49
www.wallties.com
CONCRETE FORMS PRODUCTS & ACCESSORIES
BLOCKDOWNS
ALUMINUMBLOCKDOWNS
Lightweight aluminumprovides ease in handlingfor those jobs that needfast and easy placement.C clamp to top of the wall.
STEEL
BLOCKDOWNS
One-piece specific width steel blockdownscreate bulkheads for forming garage dooropenings, access holes, orother specific depthblockdowns. Canbe C clampedinto position.
Specify nominal or full, width and depth.
EGRESS STEP BLOCKOUT
Egress Step Blockout allows for step ledges tobe poured at same time as wall for concreteEgress Bays. Treated lumber is affixed and
used for steps.
The Concrete Egress Baycan be placed at time offoundation pour or as asecondary operation.
Specify riser height, tred depth and hole pattern.
BLOCKOUTS
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
50/96www.wallties.com
50 CONCRETE FORMS PRODUCTS & ACCESSORIES
Our two-piece steel blockdown is used with lumber to form garages orother blockdown applications of various widths and depths. Can be usedfor depths of 4" to 16".
Product #SBD08000000150
The adjustable blockdownallows for depths of 8"-12"and 14"-24".
Specify nominal or full and wall thickness
BLOCKOFFS
Aluminum bulkhead plates are designed forblocking off wall ends or to bridge over dig frombasement to garage (jumps). Available in singleor combination widths x height.
Specify Nominal or Full, wall thickness andhole pattern.
BLOCKOFF/BLOCKBACKThe blockoff/blockback combination is used for blocking off wallends. It can also be used to blockback a nominal or full corner,usually at a T wall where the height drops. Can be turnedaround and used as a blockoff.
ALL STEEL ADJUSTABLE BLOCKDOWN
Our one-piece steel blockdown isused with lumber to form garagesor other blockdown applicationsof various depths. Can be usedfor depths of 4" to 16".
Specify nominal or full, depth, andwall thickness
ALL STEEL DENVER BLOCKDOWN
TWO-PIECE STEEL ADJUSTABLE BLOCKDOWN
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
51/96
51
www.wallties.com
The Brickledge Bar permits another optionfor brickledge. The brackets pin onto thetop rail of the lower form, then wood isnailed to under side of bracket. Upper panelis then placed on top of brickledge bar tocreate a 4" brickledge.
Product #AOT00000000001
SPECIAL APPLICATION HARDWARE
90 ANGLE CLIP
Versatile 90 angle clip can be a substitutefor full length outside corner angle to createan outside corner using fillers.
Steel Product #SCL90000000000Aluminum Product #ACL90000000000
45 ANGLE CLIP
Our 45 angle clip with rotating pinswill affix two filler panels to form outsidecorner opposite a hinged inside corner.
Can form 35 to 55, depending upon thetightness of wedges.
Product #SCL45000000000
Unique brackets that allow another optionfor brickledge. The brackets pin onto thetop rail of the lower form and allows thenext stacked forms to be inset 4 inches or6 inches.
4"~Product #SBK040000000006"~Product #SBK06000000000
ALUMINUM CAP CLIP
The aluminum cap clip is designed to createa cap with 2"x12" lumber.
Product #ACL10000000000
CAP/FILLER BRACKET
Cap/filler brackets are used in conjunctionwith lumber to add height to a wall. Thecap filler bracket pin is inserted into the topof the form and the lumber is then nailed tothe bracket. May also be used to construct
job site plywood fillers when you need anextra filler or where you need to pass a pipeor other object through the form.
Product#SBK10000000000
BRICKLEDGE BAR
SADDLE BRACKET
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
52/96www.wallties.com
52
The window clamp is used at the topof the wall when a drop-in windowbuck is used. This clamp ensures thatthe window buck maintains a tight fit.
Product #SCP13000000000
The deck slide clamp is used with the WTFledger system. Works with both the straightledger and the crown mold ledger. The deckslide clamp pin is placed through the endbar hole into the ledger slot and then theslide is engaged.
Product #SCP120000000000
SPECIAL APPLICATION HARDWARE
The plywood adapter allows the contractor toproduce a filler using 1/2" or 3/4" plywood.
Specify hole pattern and plywood thickness.
PLYWOOD ADAPTER
The Parapet Bracket is used in suspending theformwork on one side of the wall from theopposite side. This is commonly used inconcrete pool systems.
PARAPET BRACKET
WINDOW CLAMP DECK SLIDE CLAMP
Parapet Brackets arealso available to offsetsame height forms.
Aligner clamp with 5/8" pin, " gap is usedto pin aluminum brickledge to top of forms.Also used to pin top rail to bottom rail instacking and cap form applications.
The Continuous Brickledge Bar permitsanother option for brickledge, the bar pins
onto the top rail of thelower form. The upper
panel is then placed tothe upper brickledge.This method eliminatesthe use of lumber.
CONTINUOUS BRICKLEDGE BAR
ALIGNER CLAMPS
LONG
SHORT
CONCRETE FORMS PRODUCTS & ACCESSORIES
For use when stacking and enbar holes donot line up.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
53/96
53
www.wallties.com
This practical tool creates movementof wall when prying against footing.Permits one-person leverage to moveforms and square corners. Theheavy-duty steel chain is attached tothe pin on the bottom of the form.Leverage end is heat-treated forextended life.
Also available with hook forchain adjustment.
Product#AOT10000000000
STRING LINE ATTACHMENT
String line attachment is clamped to the topof the OSC and is used to align the wall.
Product #SOT20000000000
Available in the following sizes:
13'6" - Ideal for 9' tall wallsProduct #ABR00000013600
10'6" - Ideal for 8' tall wallsProduct #ABR00000010600
5'3" - Ideal for 4' tall wallsProduct #ABR00000005300
Used to strip panels fromtop of wall. Ideal for
brick-faced forms.
Product
#SPU10000000000
SIDERAIL PULLER
Designed to remove panels fromground level.
Specify left or right hand.
Product #SOT10000000000
This tool is for moving the wall afterforms are set.
Product #AOT20000000000
The turnbuckle allows adjustmentwithout moving brace. Easilyattached to either lumber or metalpipe to manipulate wall bracesthat pin to the form.
Product #SBR10000000000
WALL PULLER
ALUMINUM WALL BRACEWALL ALIGNER
TURNBUCKLES
HAND PUNCH
Our hand punch will add random pinholeswith just a little punch. Holes can be addedto side or end rails quicklyin the field.
Shipped with one 11/16"die set.Other die sets availableHandles sold separately.
Product #SOT40000000000
ESSENTIAL EXTRAS
FORM & CORNER PULLER
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
54/96
54
www.wallties.com
ESSENTIAL EXTRAS
WIRE TIES
5 "~Product #SWT550000000006 "~Product #SWT650000000008" ~Product #SWT80000000000
5,000 per roll
TIE TWISTER
Used to tie wire ties quickly and easily.
Works with any size wire tie.
Product #SOT30000000000
BOLTS
Foundation bolts, 100 per bag" x 8" ~ Product #SB005080000000
" x 10" ~ Non-GalvanizedProduct #SB005100000000
" x 10" ~ GalvanizedProduct #SB0G5100000000
Alsoavailable withnut and washer.Additional sizes available.
TIE BREAKER BAR
Vertically breaks ties quickly andeasily without gouging the wall.
Product # SOT15000000000
ROD SUPPORT
Designed to hold rebar in position whileplacing concrete in footings.
Single~Product #SR010000000000
Double~Product #SR020000000000
HURRICANE STRAP
3,500#~Product#SB005300000000
Used to strip ledger and to break ties incrown mold ledger applications. The slidehammer is used to ease the stripping processof crown molding and wall panels under adeck. Also used to vertically break crown
molding ties.
Product #SOT10000000000
SLIDE HAMMER
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
55/96
55
www.wallties.com
Hooks quickly and easily onto a ready-to-mix chute.The WTF 5' vinyl tube trunk allows direct flow incumbersome areas. Splashing and overspills aregreatly reduced, making it ideal for concreteplacement in footings, piers, and flatwork.
Can bemodified for
use with skidloader mounted
concrete buckets.
FOOTING CHUTE
FOOTING CHUTE HOPPER
Product #CUF11000000000
FOOTING CHUTE TRUNKProduct #CUF12000000000
FOOTING CHUTE CLAMPProduct #CUF13000000000
FOOTING CHUTE COMPLETEProduct #CUF10000000000
POURING BOARDS
Lightweight, totally aluminum boardconstructed with L shaped bracket on backthat slips over the top of the form. Naturally
helps reduce spillage and removal of form oiloff panels at discharge locations. Directsuniform flow of concrete during placement.
Product#APO10000000000
STANDARD BOARD
EXTENDED BOARD
Designed with an extended
handle for ease of use.
Product#APO11000000000
5 GALLON SPRAY TANKS
Compact 5 gallon hand tank allows for easyapplication to forms. Lightweightstainless steel with 4' hose and gun.
Replacement parts are
available.
5 gallon tank w/Cresset .80015 tip~Product #SPRA1000000061
5 gallon tank w/Regular .4005 tip~Product #SPRA1000000062
60 GALLON SPRAY TANKS
Our 60 gallon spray tank comes complete with a 100' hose and a4' wand. When ordering please specify spray tip size.
Replacement parts are available.
60 gallon tankw/Cresset tip~Product#SPRA1100000000
60 gallon tankw/Regular tip~Product#SPRA1400000000
POURING ACCESSORIES
*Spray tanks should not be filled over 2/3 full.Both tanks are designed with safety filler caps.
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
56/96
56
www.wallties.com
CONCRETE CHUTES
WTF smooth flow aluminum chute isdurable and lightweight. Our chutes aremade of extruded heavy gauge aluminum
and reinforced with cross beams andsecured attachment chain.Available sizes: 6' - 24' on 2' incrementsThe aluminum chute weighs lessthan 5 lbs. per foot which makes iteasy to handle by a single worker.
Flare added for ease of use.
Available sizes: 8' - 26'on 2' increments
Chutes for special applications also available.
STANDARD CHUTES
STANDARD CHUTES WITH FLARE
Used to assist in theconsolidation and
flow ofconcrete.
Made of lightweightaluminum tube. It will notsplinter or break.
Available in 12' length ~Product #AOT30000000000
Fabricated with lightweight aluminumand made to drag concrete insideforms.
Product #APO12000000000
Specify wall thickness
ALUMINUM PUDDLE STICK POURING SHOVEL
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
57/96
57
www.wallties.com
Crete-Lease 727 Release AgentCrete-Lease 727 is a mineral based release agent that has been used for more than 25 years. It applies at low and highambient temperatures and it exceeds all state and federal VOC regulations.
Advantages: Crete-Lease 727 permits easy stain-free removal of forms, formliners, pallets, etc.from hardened concrete. It:
~ Cuts form clean-up time up to 70% when properly applied.~ Can reduce bugholes on concrete surfaces.~ Does not interfere with adhesion of caulk, architectural coatings, paint,
sealers, and curing compounds on cured concrete surfaces when properly applied.~ Works superbly on aluminum forms.~ Can be applied in sub-freezing or very hot temperatures.~ Reduces incidences of skin rashes to an absolute minimum.~ Can produce both high visual impact (CCS 2) and typical concrete
surfaces (CCS 3, CCS 4, CCS 5).
Ready to use - Available in:5 Gal. Pail ~ Product #CMCR727000000555 Gal. Drum ~ Product #CMCR7270000055275 Gal. Mega Pack ~ Product #CMCR7270000275
RELEASE AGENTS
Crete-Lease BREAK-IN Aluminum Form ConditionerSeasons new aluminum forms before first use. Reduces reaction withnew aluminum and concrete.
Crete-Lease Break-In oxidizes the aluminum surface to reduce reaction.~ Conditions forms even at 45F.~ Is not as messy as liming.~ Removes residual oils.~ Is biodegradable.
Available in: 5 Gal. Pail ~ Product #CMCR7280000005
I've tried other release agents, butwith Crete-Lease 727, I've neverbeen more satisfied. Its easy to use,one light spray and my forms stayclean.I never have to clean my forms.
Bill CurthShawnee, Kansas
CONCRETE FORMS PRODUCTS & ACCESSORIES
Many contractors find that applying ReleaseAgent to forms while still in the basket saves a
step in form setup and creates labor savings.
As a 2nd generation poured wall contractor,I have used a variety of release agent oils.Cresset Crete-Lease 727 uses less oil perfoundation keeping my cost per wall the sameas some of the cheaper oils.I don't have toclean my forms after using Crete-Lease 727.It is the best oil and best value.
Paul DusselierRaymore,Missouri
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
58/96www.wallties.com
58
MATERIAL HANDLING EQUIPMENT
If you have invested money in a quality crane truck, now may be the time to invest in quality material handling equipment.In the past two decades we have proven to be the leader and innovator of material handling baskets.
WTF designs and manufactures the highest quality form baskets in the industry.
A-Frame Basket available for all heights on36" wide panels.
FULL PANEL BASKETS
WTF builds heavy duty baskets. Each full panelbasket is equipped with two 2"x12' nylon strapswith a ratchet handle and four wear pads. Thecapacity of the forms held in each basket isdetermined by your cranes lifting capacity.When ordering please specify lifting bell or loop.
Expanded metal is placed incenter of basket to allow forstorage of accessories neededon the job site.
Heavy Tube construction allows mini-mal bracing. This allows for easier form
storage and removal. Because of lighterconstruction many form baskets in theindustry require additional side bracing.This type of basket construction cancreate additional labor when removingor storing forms.
Safety Chains are alsoincluded in
A-Frame Baskets.
The Baskets are built with ataper at the base to addadditional stability to formsbeing stored.
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
59/96www.wallties.com
59
A wide variety of different basket designs are available. These include the Laydown Filler Basket and the Standup Filler Basket.WTF designs the baskets to accommodate the equipment of the contractor.
LAYDOWN FILLER BASKET
FILLER BASKETS
STANDUP FILLER BASKET
MATERIAL HANDLING EQUIPMENT
CONCRETE FORMS PRODUCTS & ACCESSORIES
48" stacker basket also available.
*Note: Has four straps.
FILLER BEDS
WTF custom designs filler beds around the customer's truck and forms.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
60/96
60
www.wallties.com
WTF utilizes a 2 lb. densityPerformGuard EPS, a termiteresistant expanded polystyreneinsulation.
~ Resistant to termite damage~ Resistant to carpenter ant
damage~ Non-toxic, safe to handle~ Incorporates EPA registered
material~ Meets code requirements for
ground contact use~ Cost effective
Various sizes available
WTF INSULATION
INSULATION TIE FOAM
Sold in2 1/2" lengths
T-SECTION
I-SECTIONF-SECTION
Patent #5,987,830 Patent #5,987,830
The F Sectionis used atcorner
transitions,window anddoor openings,top of concretewall, deck, andstructural slabto create addi-tional attachingpoints and atermite barrier.
The I-Section along with the
insulation tie ensures that
insulation stays in place for
concrete placement.
Also provides an
additional
attaching
point.
The T-Section is utilized in36" wide insulation applications(such as foundations). It isplaced in the center ofinsulation to create additionalattaching points for exteriorwall treatments.
This tie is used to incorporate foam insulation. These ties are
designed with a specific breaking point so there is a clean
break off and will break easily behind the insulation to
eliminate thermal bleeding. It also has a notch to hold
the I-Section in place, which eliminates any foam
notching which is required in other insulating
systems. Breakback is determined by
thickness of foam.
Product #TTSP0400002101
Outside form is put into place.
Insulation is begun at the corner utilizing theWTF F-Section.
WTF INSULATION PROCESS
CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
61/96
61
www.wallties.com
WTF INSULATION
The process is then continued throughout thewall. Fillers will need to be sized for appropriatelocations and T walls. Once the setting iscomplete, concrete can be placed.
Once the concrete work is complete, the F, I and T Sections can be utilized as attachingpoints for various external finishes.
Wall-Ties & Forms recommends PerformGuard
EPS, a (registered) trademark of AFM Corporation. *Tested
against termites and carpenter ants. Manufacturer has specific species on file. PeformGuard is not a barrier sys-
tem. Insects may enter through other access areas. AFM products are produced exclusively by Partner Plants in
AFM Corporation. PeformGuard, and AFM are registered trademarks of AFM Corporation.
**Protected under U.S. Patents No. 5,194,323 and No. 5,720,108. Other U.S. and Foreign Patents Pending.
2001 AFM Corporation
4" PerformGuard
I-Section
8" Breakback Tie
8-8 Standard Form
The system is so versatile andinexpensive to use, unlike ICFs
where there is no choice but toinsulate every wall and everysection of the wall.
When testing the adhesion between
the insulation and poured in place
concrete with no retainers used, the
conversion rate is 1,150 lbs. of pull
per square feet.CONCRETE FORMS PRODUCTS & ACCESSORIES
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
62/96
62
www.wallties.com
WATERPROOFING AND DAMPPROOFING PRODUCTS
WATERPROOFING & DAMPPROOFING
DECO 20 CLEAR is a code approved penetrating sealer.The product is primarily used to dampproof the exterior ofpoured concrete, pre-cast, or masonry block foundationwalls. DECO 20 CLEAR can also be applied to the insideof existing walls to stop moisture penetration.
~ NO SPECIAL CLOTHES OR RESPIRATORS NEEDED FORAPPLICATION
~ NO VOC'S MEANS NO SOIL CONTAMINATION~ SPRAYER AND HANDS CLEAN UP WITH WATER~ CAN BE PAINTED OR COATED~ CAN BE APPLIED TO DAMP WALLS~ CAN BE APPLIED TO THE COMPLETE FOUNDATION WALL~ NO GRADE LINE PROBLEMS ASSOCIATED WITH TAR~ DRYS CLEAR WITHIN 2 HOURS, NO BACKFILL INTERRUPTIONS~ APPLY WITH HAND SPRAYER, NO EXPENSIVE EQUIPMENT~ FAST APPLICATION SAVES TIME~ MANUFACTURER'S WARRANTY
Available in:5 gal. pail ~ Product #DECO2000000000
DECO 20 SEAL is a code approved waterproof graycoating. The product will bridge cracks and stop waterthat is under hydrostatic pressure. DECO 20 SEAL isused with an airless sprayer to waterproof the exterior ofpoured concrete, pre-cast, or masonry block foundationwalls. DECO Tie Patch replaces tar patching productsused to seal tie ends.
~ NO SPECIAL CLOTHES OR RESPIRATORS NEEDED FORAPPLICATION
~ WATER CLEAN UP~ CAN BE PAINTED~ CAN WATERPROOF THE ENTIRE WALL TOP TO BOTTOM~ NO GRADE LINE PROBLEMS~ CAN APPLY TO DAMP WALLS~ MANUFACTURER'S WARRANTY
Available in:DECO 20 Seal-55 gal. drum #DECO2020000000DECO 20 Seal-5 gal. pail #DECO2010000000
DECO Tie Patch-1 gal. pail #DECO0500001000
DECO 20 CLEARTM
DECO 20 SEALTM
SEE ICC Evaluation Service Legacy Report #93-04.
SEE ICC Evaluation Service Report #1416.
5 gal. spray tank ~ Product #SPRA1000000062
Lightweight stainless steelhand held tank with 4'hose and gun.
http://www.wallties.com/http://www.wallties.com/ -
7/28/2019 Wall Ties Formwork
63/96
New Speedclip Installation is twice as fast and three times stronger than plug and washerinstallations.
All weather installation makes scheduling easy.Platon can be hand nailed (green concrete) whilethe forming crew is on the job-site strippingforms.
No additional protection needed.
Exceptional ("+) crack bridging ability.
Overlap 6" horizontally for deep foundations to16'.
Use under slab instead of 6-mil poly (which getsbrittle over time) for a permanentmoisture barrier.