vita® suprinity® - welcome to straumann · 2020-05-26 · vita® suprinity® glass-ceramic...
TRANSCRIPT
VITA® Suprinity®Glass-ceramic manufactured by VITA Zahnfabrik H. Rauter GmbH & Co. KG
Zirconia-reinforced, high-strength glass-ceramic material for reliable full-contour restorations
EFFICIENCY Easy processing thanks to material blanks properties providing edge stability, good polishing characteristics and high firing stability
STRENGTHHigh strength thanks to a zirconia-reinforced glass-ceramic matrix
ESTHETICSVITA® Suprinity® is a highly esthetic material with integratedtranslucency, opalescence and fluorescence
In-house milling
C/M series
2
Available shades ► VITA® Suprinity® blocks (for in-house milling) are available in two levels of translucency: HT
(High Translucent) and T (Translucent). Both translucencies are available in 8 shades: 0M1, A1, A2, A3, A3.5, B2, C2 and D2.
TOOTH-BASED
Inlay Onlay Veneer Partial crown Coping
n/a n/a
Full-contour crown
Telescopic crown
Bridge/barframework
Full-contour bridge
Vestibular veneering
ABUTMENT-BASED (AVAILABLE WITHIN THE CARES® X-STREAM™ SOLUTION)
n/a n/a
Coping on Ti-Base
Full-contour crown on Ti-Base
Coping on CAD/CAM abutment
Full-contour crown on CAD/CAM abutment
Available indications ► For final restorations ► For single tooth only
Recommended indicationPossible indicationNot possible indication (n/a)
VITA SUPRINITY C14 BLOCKS (EACH ARTICLE CONTAINS 5 BLOCKS)
Shade Art. for translucency T Art. for translucency HT
0M1 EN1S03024445 EN1S04024445
A1 EN1S03364445 EN1S04364445
A2 EN1S03374445 EN1S04374445
A3 EN1S03384445 EN1S04384445
A3.5 EN1S03394445 EN1S04394445
B2 EN1S03424445 EN1S04424445
C2 EN1S03464445 EN1S04464445
D2 EN1S03494445 EN1S04494445
3
WorkflowSTEPS OPTIONS
Nesting Position the restoration in the block
Milling Recommendation: Straumann® C / M series
Crystallization Recommendation: VITA® SMART.FIRE® for CARES®
Finishing PolishingRecommendation: VITA® SUPRINITY® PC Polishing Sets technical or clinicalStaining & glazingRecommendation: VITA® AKZENT® Plus LayeringRecommendation: Layering: VITA® VM 11 veneering ceramic
Cementing Adhesive Self-adhesiveConventional
Physical propertiesPROPERTIES VALUE
CTE [10-⁶ K] approx. 12.3
3-point flexural strength [MPa] approx. 420
Elastic modulus [GPa] approx. 70
Hardness according to Vickers (HV) [MPa] approx. 7000
Chemical solubility [μg/cm²] approx. 40
Chemical compositionELEMENTS WEIGHT
ZrO₂ (zirconia) 8 – 12 %
SiO₂ (silicon dioxide) 56 – 64 %
Li2O (lithium oxide) 15 – 21 %
La2O3 (lanthanum oxide) 0.1 %
Pigments < 10
Various > 10
3
Wall thickness
OnlayInlay
Veneer Partial crown Full-contour crown
≥ 1.5 mm
≥ 1 mm
≥ 1.0 mm≥ 1.0 mm ≥ 1.0 mm
≥ 0.7 mm
≥ 1.0 mm ≥ 1.0 mm ≥ 1.0 mm ≥ 1.0 mm
MINIMAL RESTORATION DESIGN
Preparation guidelines ► The preparation shall not have angles or sharp edges ► The shoulder preparation shall be with rounded inner edges and/or chamfer ► The preparation shall have retentive surfaces for conventional cementation
International Headquarters Institut Straumann AG Peter Merian-Weg 12 CH-4002 Basel, Switzerland Phone +41 (0)61 965 11 11 Fax +41 (0)61 965 11 01 www.straumann.com
Suprinity®, Akzent® and SMART.FIRE® are registered trademarks of VITA Zahnfabrik H. Rauter GmbH & Co. KG, Germany.
© Institut Straumann AG, 2019. All rights reserved.Straumann® and/or other trademarks and logos from Straumann® mentioned herein are the trademarks or registered trademarks of Straumann Holding AG and/or its affiliates.
490.
398/
en/A
/00
01/1
9