1

PROPOSED REFURBISHMENT

OF

BANK OF BARODA

AT

VIJAYA BANK , KAITHAL

VOLUME – II

(FINANCIAL BID)

TENDER

For

INTERIORS, ELECTRICAL & AIRCONDITIONING WORKS

2

INDEX

• NOTICE INVITING TENDER • FORM OF TENDER • PREAMBLE AND SPECIFICATIONS • BILL OF QUANTITIES

3

NOTICE INVITING TENDER

Bank of Baroda invites tenders, in duplicate, from contractors for the proposed Interior works of Bank of Baroda Branch at VIJAYA BANK , KAITHAL Sealed tender on Item Rate basis duly filled in this tender copy is invited from contractors for furnishing work of Bank Of Baroda branch at VIJAYA BANK , KAITHAL (Karnal Region). Earnest Money Rs.11,000/- by demand draft or pay order payable at Karnal and drawn in favour of Bank Of Baroda.

Time of Completion 21 Days. Tender Collection Tender copies will be available at Bank’s Website

bank of baroda.com from 12Th March ,2020 to 1ST April, 2020

Time, Date and Mode of submission of Tender Before 3:00 P.M. on or before 12th March , 2020 at the office of The D.G.M., Regional Office, Bank of Baroda, Opposite Deventure Hotel, Namaste Chowk, Karnal 132001.

Tender shall be submitted duly filled in two bid systems and in the following manner only:

Envelope no. –1 (Volume – 1, Tender fee and EMD) Volume – 1 (Prequalification Criteria & Technical Bid)

Favoring Amount (Rs.)

DD / Banker’s Cheque payable at

EMD Bank of Baroda

Rs.11,000/- Karnal

• Other supporting documents & credentials of the tenderer. • Additional Techno – commercial information, deviation, etc.

Envelope No. -1 must not contain Price bid or else the Bank will disqualify the tender without any further scrutiny. ENVELOPE NO. –2 (Price Bid): Price bid received in any form other than format attached in the tender will be disqualified. All the Two envelops are to have clear heading on them as TECHNICAL BID and PRICE BID and sealed properly.

4

One large envelope bearing on it the name of works PROPOSED REFURBISHMENT OF BANK OF BARODA BRANCH at VIJAYA BANK , KAITHAL And containing above two envelops shall be submitted to the Regional office addressing to The D.G.M., Regional Office, Bank of Baroda, Opposite Deventure Hotel, Namaste Chowk, Karnal 132001. Time, Date Opening of Tender : 01st April, 2020 at 3:30 P.M. The bank will not be bound to accept the lowest tender and reserves the right to accept or reject any or all the tenders without assigning any reason whatsoever. Sd/- The D.G.M., Regional Office, Bank of Baroda, Opposite Deventure Hotel, Namaste Chowk, Karnal 132 001. Date:12 March, 2020

TENDER FORM

5

To The D.G.M.,

Regional Office, Bank of Baroda, Opposite Deventure Hotel, Namaste Chowk, Karnal ,132001.

Dear Sir, Ref: Proposed Civil & Interior Works of Bank of Baroda branch at VIJAYA BANK , KAITHAL

Having examined the plans, specifications and schedule of quantities prepared by the consulting Architect’s ……………………………………………….. and satisfying ourselves as to the location of the site and working conditions, I/we hereby offer to execute the above works at the respective rates which I /we have quoted for the items in the Schedule of Quantities. I/We herewith deposit Rs.11,000(Rupees Eleven thousand only) by Demand Draft or Banker’s Cheque drawn in favour of Bank of Baroda as Earnest Money Deposit for the execution of the works at my / our tendered rates together with any variations should the work be awarded to me /us. In the event of this tender being accepted, I/ we agree to enter into and execute the necessary contract required by you. I/ we do hereby bind myself/ ourselves to forfeit the aforesaid deposit of Rs.11,000/- (Rupees Eleven thousand only) in the event of our refusal or delay in signing the Contract Agreement. I/we further agree to execute and complete the work within the time frame stipulated in the tender documents. I/ we agree not to employ Sub- Contractors without the prior approval of the Bank. I/ we agree to pay sales Tax, Works Contract Tax, Excise Tax, Octroi, VAT, duties, all Royalties and all other applicable taxes prevailing and be levied from time to time on such items for which the same are leviable and the rates quoted by me/ us are inclusive of the same. I / we understand that you are not bound to accept the lowest tender or bound to assign any reasons for rejecting our tender. I/ we further understand that Bank of Baroda may award Contracts for Interior to more than One Contractors and that I /we shall make no claims whatsoever if Bank Of Baroda accept only a part of my/ our tender. We unconditionally agree to Bank of Baroda’s preconditions stipulated in the tender documents. I/ we agree that in case of my /our failure to execute work in accordance wit the specifications and instructions received from the Owner or the Architect/ Consultants appointed by the Bank, during the course of the work, Bank reserves the right to terminate my contract and forfeit the Earnest Money deposit paid by me in additions to recovery of all the dues to the Bank from the payment receivable by me. Further I may also be barred from tendering in future for the Bank and its subsidiaries.

6

I/ we enclose demand draft/ banker’s Cheque for Rs.11,000/- (Rupees Eleven thousand only) towards earnest Money Deposit in envelope No. -1. I/ we agree to keep our tender open for 120 days from the date of opening of Envelope no. -2 i.e., Technical bid. Any Commercial disclosure in the envelope No. -1 and/ or 2 will disqualify me / us without any further scrutiny. I /we enclose herewith the completed tender documents duly signed in duplicate in envelope no. -3 (Commercial Bid). Yours truly, Signature of the Tenderer, Place: Date: PREAMBLE AND SPECIFICATIONS The quantities given in the schedule of quantities are approximate and subject to variations without vitiating the contract. Pricing The rate for each item of work shall, unless expressly stated otherwise, include the following (but not limited to the list given below) for the completion of works in all respects as per the conditions of Contract, Technical specifications, drawing etc. All taxes such as Octroi, Sales Tax, Work Contract Tax, Royalties, Transportation, Freights, Packing and forwarding charges, Insurance etc.

7

All requirements and expenses for completion of work as per rules and regulations of Local bodies, State Government and Central Government of India. All materials, equipments, accessories, consumable, controls and instruments, tools, tackles, plants, scaffolding / double scaffolding labour, maintenance, fixing, cleaning, making good hauling, hoisting etc., Waste on material and labour. Loading, unloading, handling / double handling, setting out protection from weather, temporary supports, platforms etc., and the maintenance, of the same, dismantling of temporary works, disposal of debris and all other labour necessary for the execution of works. Testing the installation as often as necessary, contractors to arrange for all special instruments and tools required for such testing. Painting of all equipment, pipes, and supports etc., as per color codes to be decided for various systems. Apportion of costs for general facilities to be used by the Contractor’s staff such as lifts, electricity, telephones etc. during execution if such facilities are provided by other contractors and who arrange for such facilities in the first instance. Fees for testing the materials, equipment or overall installation by appropriate authorities. Supervising Civil / Masonry / Carpentry Works done by other agencies on behalf of the Bank for Interior Contractor. All requirements of specification and drawings. Description of work given in the schedule of quantities is a brief description and shall be read in conjunction with specifications and drawings. Removal of POP covering and carting away all unwanted material including POP. The rates quoted by the Tenderer will be deemed to be for the finished work complete in all respects with accessories, fittings, mounting arrangements normally provided with such equipment and /or needed for execution, completion, safe operation of equipment as required through they may not have been specifically mentioned in technical specifications, drawings and /or schedule of equipment. All minor masonry, Carpentry and Civil works such as cutting opening in masonry walls, internal partitions, chasing of walls, etc. and making good the same to match existing

8

works shall be provided by the contractor, whenever asked for by the Architect / Consultant. SCHEDULE OF QUANTITIES All items of work contracted for shall be executed strictly in accordance with the description of the item in the schedule of Quantities, relevant drawings and specifications and conditions of the contract and established Engineering practices. The rate for each item of work included in the schedule of quantities shall unless expressly stated otherwise include cost of: All materials, fixing materials, accessories sequence of operations, appliances, tools, plant equipment, transport labour and incidentals required and completion of the work called for in the item and as per specifications and drawings completely. Wastage on Materials and Labour: Loading, transportation, unloading, handling as necessary, hoisting o all levels, and setting, fitting and fixing the position, protecting, disposal of debris as directed an all other labour necessary and to fully complete the job in accordance with contract documents, good practice and recognized principles of trade laid down in codes of Practice. Liabilities, obligations and risks arising out of Conditions of contract. All requirements of specifications, whether such requirements are mentioned in the item or not shall be provided for the specifications and drawings where available are to be read as complimentary to any part of the schedule of quantities and any work called for in one shall be taken as required for all similar items. In the event of conflict between schedule of Quantities and other documents including the specifications the most stringent among them shall apply and the interpretations of the consultants/ Owner shall be final and binding. The contractor shall be paid for the actual quantity of work executed by him in accordance with the drawings at the accepted rates. This schedule shall be fully priced and the extensions and totals duly checked. The rates for all items shall be filled in INK. The entries under amount column shall be rounded off to the nearest Rupee. No alterations whatsoever is to be made either to the description of items in the Schedule of Quantities or specifications unless such alterations, is clarified in writing by the consultant/ owner. Any such alterations, notes or additions shall unless clarified in writing be disregarded when tender documents are considered.

9

Any observation on BOQ should be made in the letter accompanying technical bid for proper consideration and on disfiguring or overwriting in the documents is permitted. In event of an error occurring in the amount column of the schedule, as a result of wrong extension of unit rate and quantity, the unit rate quoted by the Tenderer shall be regarded as firm and the extensions shall be amended on the basis of rates. Al errors in totaling in the amount column and in carrying forward totals shall be corrected. Unless otherwise stated, all measurements shall be taken in accordance with Indian standard for building of Measurements IS 1200 latest revision effective on the date of measurement for interior items as applicable. Any errors in quality of items from the contract schedule shall not vitiate this contract but shall be corrected and deemed to be a variation by the Architect / Consultant / Owner. DRAWINGS AND DATA Within two weeks of placement of order / letter of intent, contractor shall furnish the following data in triplicate for approval by architect / consultant / Owner. General arrangement of drawing of the equipment on orders showing plan, elevations, and sectional views, mounting details. BILL OF MATERIALS Descriptive catalogues, characteristic curves, duty point efficiency factor and technical particulars of all the various equipment’s offered. SPARE PARTS AND MAINTENANCE FOR MATERIALS SUPPLIED Tenderer shall offer along with the bid, duly recommended by manufacturer set of spare parts required for a period of 1 year continuous operation. Itemized unit prices with exact quantities recommended for these spares shall be separately indicated for consideration of the Owner / Consultant. DOCUMENTS MUTUALLY COMPLIMENTARY The several documents forming the contract are to be read as mutually complementary to each other and in case of ambiguities/ discrepancies, the same shall be explained and clarified by the Consultant/ Owner to the Contractor in what manner the work is expected to be carried out to meet the end requirements.

10

INSTRUCTIONS DURING EXECUTION On the advice of the Owner, the consultants may issue further drawings and written instructions, details, directions and explanations collectively referred to as “Site instruction” in regard to: Variations for modification of the design, quality or quantity of works as addition or omission or substitution of any work therein. Any discrepancies in the drawings or between the schedule of quantities and /or specifications and/ or drawings. Removal from the site any material brought by the contractor and substitution of any other materials therefore. The dismissal or removal from work of any person employed thereupon. Removal / reexamination of any works executed in case of doubt of any nature. Opening up for inspection of any work covered up without proper tests by the Architect / Consultant. Oversight on the part of the Architect / consultant / his assistant to disapprove any defective work or material shall not prejudice the Owner / Consultant, thereafter to disapprove such work or materials and to order pilling down, replacement, removal breaking up or reconstruction. The contractor shall make his own arrangement for the engagement of all labour and shall be responsible for regulating their service conditions, work conditions in conformity with all Acts, regulations, Rules or order of competent Authority under relevant laws in force during the pendency of the contract. Contractor shall indemnify the Owner from all claims relating to the workers/ staff / sub – contractors, Salaries, Wages, Overtime, leave, Provident Fund, Medical Facilities, Gratuity, Bonus or any other claim as applicable and stipulated in any statutory provisions, rules or order of competent Authority. All materials so far as procurable shall be of the reputed make in the category of manufacture and bear the stamp of quality of the Bureau Standards wherever applicable. The contractor shall furnish documentary proof, test certificates and guarantees as relevant to such materials from manufacturers, which shall match with the date of procurement.

11

TENDER FOR THE INTERIOR & ELECTRICAL WORKS IN BANK OF BARODA BRANCH AT VIJAYA

BANK , KAITHAL

SPECIFICATIONS/ BRANDS/ MAKE OF ITEMS TO BE USED

DESCRIPTION BRAND FURNISHING WORKS:

a) Board/ Ply : Green Ply(Ecotec), Century PLY(Sainik), Bhutan Tuff.

b) Laminate : Formica, Greenlam, Aica, Euro,

Amulaya c) Door Closer/ Floor Spring : Everite, Godrej, Sandhu

Conforming to ISI Specifications d) Drawer & Keyboard, Slide Rails : Ebco, Godrej e) Glue for fixing commercial : Fevicol (Pidilite)

Board / Laminate f) Glass : Saint Gobain, Tata Asahi, Modi Float g) Mortise Latch & Lock : Godrej, Harrison h) Vertical Blinds : Vista Levlor/ Mac i) Tapestry/ Leather Foam : Harmony, Vimal, Bhor j) Aluminium Sections : Jindal, Hindalco k) False Ceiling : Gyp Board / La Gyp & Gypsum

Marked “Gyp steel” l) Synthetic Enamel : Asian, Nerolac, ICI m) Emulsion paint/ Plastic paint, : Asian, Nerolac, ICI

OBD n) Patch Fittings for glass : Godrej/Dorma/Ozone

ELECTRICAL WORKS: a) Wires : M/s Anchor, Havells, Finolex, RR cables.

b) Modular Switches : M/s Anchor, Havells, Le Grand, Crabtree. c) Switch Gears : M/s Havells, Indo Kapp, Hager. d) Distribution Board : M/s L & T, Hager. e) On/Off Switch : M/s Le Grand, GE f) Composite drain pipe : M/s Kitec, Jindal (For Air Conditioning Drain)

12

DETAILED BILL OF QUANTITY FOR FURNISHING , ELECTRICAL & AIR CONDITIONING WORK OF VIJAYA BANK BRANCH, KAITHAL

A FURNISHING WORK S.

No.

Description Quantity Unit 1 FALSE CEILING

a Providing and fixing GYPSUM BOARD FALSE CEILING in levels as per the detailed drawing - made up of G.I frames as specified by Gypsum India limited 1mm and 12mm thick Gypsum board with suitable suspenders fixed to the ceiling. Ceiling section, perimeter channel, suspenders etc. shall be standard sections supplied by Gypsum India LTD. Spacing of intermediate channels shall be at 1200 mm c/c, and ceiling section at 457 mm c/c the work includes taping and jointing, applying primer, two or more coats of plastic emulsion paint of approved shade ICI/ ASHIAN PAINTS make, making cut-out for light fixtures, etc. The Final court shall be done with FOAM ROLLER, and no brush marks should be visible. Providing of perimeter channels/ beading etc. as per drawing complete in all respects.(All measurement in sqft only)

940 sqft

b Metal 2X2 grid false ceiling, False Ceiling with finishing of joints, cutouts to accommodate light fixtures. FOR E-LOUNGE

112 sqft

2 PARTITIONS

13

Providing & fixing full ht. Partition (up to ceiling) with 2”x 1½” sal wood framing, with 6 mm waterproof plywood fixedon both sides, with 12mm float glass as per design, the exposed surface of plywood to be finished with 1mm thk. approved shade of laminate on both sides, to provide the necessary wooden supports of min. 2”x1½” size, glass to behold by teak wooden beading (Area of the partition including the glass above). Framing all around the glass/ opening tobe of teak wood duly finished in enamel paint. All complete as per satisfaction of Bank/Architect.(Rate to be inclusive with all necessary hardware items & )(Flush door also taken in this item)

363 sqft

a

Providing & fixing low ht. Partition (4'-6" high) with 2”x 1½” sal wood framing, with 6 mm waterproof plywood fixedon both sides, with 12mm float glass as per design, the exposed surface of plywood to be finished with 1mm thk. approved shade of laminate on both sides, to provide the necessary wooden supports of min. 2”x1½” size, glass to behold by teak wooden beading (Area of the partition including the glass above). Framing all around the glass/ opening tobe of teak wood duly finished in enamel paint. All complete as per satisfaction of Bank/Architect.(Rate to be inclusive with all necessary hardware items)

0 sqft

14

b CASH CABIN PARTITIONProviding & fixing of CASH CABIN PARTITION (HT. 7'-3") (partly glazed (6mm glass) as per design), made of 2" x 2" 1st quality Partal wood frame are 2’-0” c/c both ways 6mm commercial ply of CENTURY/ Bhutan Tuff Make on both faces finished with 1mm thick laminate of CENTURY/ AMULYA/ GREENLAM Make, shade as approved. The work includes providing a 6" x 9" voucher cut out with tray, spirit polishing of shade on woodwork and steam beach beading etc. Including doors but excluding cost of door closers mortise locks. Complete in all respects to the complete satisfaction of the Architect./Engineer.

110 sqft

c Cash Cabin front Partition With 12 mm Glass including fixing. Complete in all respect.

74 sqft 3 ACCESARRIES a Knight latch for cash cabin door (Make Godrej) 2 no. b Mortise locks (with handles.(Make Godrej) 6 no. c Hydraulic Door closer.(Make Godrej/Universal) 2 no. d Floor springs.for main entrance door. And the ATM

door (make Godrej , Universal, Sandhu) 2 no.

4 ENTRANCE DOOR a MAIN ENTRANCE DOOR WITH LOGO :- Providing

and fixing main entrance door (Branch+ATM) of 12mm thick clear toughned glass with etching and bank logo. (for size reffer drawing)

33 sqft

c FIXED GLAZING (BRANCH+ATM)Providing and fixing external fixed glazing comprising of 8 mm Modifloat, Saint Gobain, Asahi make clear glass with top, bottom and vertical frame comprising of black powder coated aluminium members, glass to be laminated with clear antishatter film on one side. Approximate 100mm top & botttom member, approximate 100mm vertical members.

38 sqft

5 COUNTERS AND TABLES

15

a Providing and fixing MANAGER'S TABLE 6'-0" x 2'-9" x 2'-6" and 10mm beveled glass of approved make to be fitted on top obtain the total height of 2’-6” as per detailed drawing, made up of 19mm commercial board of CENTURY/ BHUTAN TUFF approved Make and finished with 1 mm thick laminate of make, and shade as approved, as per detailed drawing(with one side drawer unit and another side drawer unit). The size of the drawer should be 1'-9"x2'-6" and shall be provided with drawers sliding on telescopic channels (Ebco/hetich make) and one cabinet with proper locking arrangements and keyboard with telescopic channels (Ebco/hetich make) . Tabletop shall be finished with 1.0mm thick laminate of approved shade & quality. The work includes providing and fixing of foot rests, shelf for CPU, furniture locks, wire managers, spirit polishing of steam beach/ white cedar beading etc. and The inner exposed surfaces to be painted over one coat of primer and enamel paint of approved shade. complete in all respects to the entire satisfaction of the Architect/Bank.

Manager Table of size (6'-0" x 2'-9"x 2'-6") as per drawing (Must be kept loose without fixing with wall or floor ) 1 No.'s.

b SIDE CREDENZAS (Must be made loose without fixing to wall/partition.) :

Providing and fixing SIDE CREDENZAS of size 3'-0" x 1'-3" x 2'-3" made of 19mm commercial board CENTURY/BHUTAN TUFF finished with 1 mm thick laminate of approved Make and shade on top, back, sides and front having two drawers and cabinet below complete with all accessories like locks, handles, megnetic catcher etc. Teak wood beading on all exposed edges with spirit polish. (Should not be attahced with partitions, wall or floor)

1 no.

16

c CASH COUNTER Providing and fixing of fixing cash counters & cashier table of size 5’-0” x 2’-6” x 2'-6" with two levels i.e., 2’-6” & 4’-0” ht. 19mm commercial board of CENTURY/ Bhutan Tuff Make and finished with 1 mm thick laminate of CENTURY/ AMULYA/ GREENLAM Make, shade as approved and as per detailed drawing. 2'-6' wide working table top, key board tray, 1'--6"X2'-0" drawer with telescopic channels (Ebco make)(TOP DRAWER SHOULD BE DIVIDED INTO SECTIONS SO AS TO PILE DIFFERENT CURRENCY NOTES SEPERATELY) and cupboard. All exposed surfaces (such as counter front, sides, drawers and cupboard etc) to be finished with 1mm thick laminate of approved make. Tabletop shall be finished with 1mm thick laminate . The inner exposed surfaces to be painted over one coat of primer and enamel paint of approved shade. The work includes fixing of furniture locks, wire managers, spirit polish of steam beach wood beading/ lipping etc. complete in all respects to the entire satisfaction of Architect. Transaction top should be minimum 18"

2 Nos.

d WORK STATIONS TABLE (Size 4'-0" x 2'-3" x 2'-6")Providing and fixing of COMPUTER work Stations as per layout plan obtain the total height of 2'-6" high working top ( As per drawing) made up of 19mm commercial board of CENTURY/ Bhutan Tuff Make, finished with 1 mm thick laminate of CENTURY/ AMULYA/ GREENLAM Make, shade as approved as per the detailed drawing . The tables should have 4'-0"X2'-3" table top as per approved shade and color. All exposed surfaces (such as counter front, sides, drawers and cupboard etc) must be finished with 1mm thick laminate of make Sunmica / Century / Greenlam . Tabletop shall be finished with 1mm thick laminate. The inner exposed surfaces to be painted over one coat of primer and enamel paint of approved shade.Each unit of table shall be provided with keyboard tray with telescopic channels(EBCO). Tabletop shall be finished with 1.0mm laminate of approved shade & quality. The work includes fixing of wire managers, locks, footrests, spirit polishing the steam beach beading, lipping, exposed frame, etc. as per drawings and the inner exposed surfaces to be painted over one coat of primer and enamel paint of approved shade. Complete in all respects to the complete satisfaction of the Architect/Bank.

10 no.

17

6 MISCELLANEOUS FURNITURE a STORAGE CABINETS WITH LOCKS, HANDLE (Must be

kept loose without fixing to wall/Partition; each 5 feet storage must be made as independent unit and all the side (back, side, front & top side) of the storage also to be finished with mica and 19mm commercial boardProviding & fixing STORAGE CABINETS of 9'-3"x1'-6"x4'-6" (Manager Cabin ) , 6 nos of size 8'-0"x1'-6"x4'-6" + 2'-9" x 1'-6" x 4'-6" + 1'-0" x 1'-6" x 4'-6" as per layout plan made up of 19mm commercial board of CENTURY/ Bhutan Tuff Make and finished with 1mm thick laminate of CENTURY/ AMULYA/ GREENLAM Make, shade as approved and per detailed drawing. With BOX SIZE OF 2.5 FEET WITH 2-3 shelves made up of 19mm thick commercial board, each drawer(with lock) & cabinet(with lock) 19mm thickness portion every place must be finished with proper liping/ margin finish. In side to be painted over two coat of primer and enamel paint of approved Make and color The work includes supplying, fixing of hinges, magnetic catchers, handles, locks, teak lipping etc complete in all respects to the complete satisfaction of the Architect.

58 rft

b Providing & fixing wooden cabinet in pantry of size( 4'-0” x 1’-0” x 2’-0”) height made of 10mm thk. Commercial board & 6mm th. Ply; finished with 1mm thick laminate, polish, inside painting, complete finished with golas/ margins, handles, hinges, and catchers, front openable shutters, as per requirement

1 Nos.

c Providing and fixing 35mm flush doors finished complete with 1mm thick laminate of approved shade on both the faces (FOR CASH CABIN)

4 No.’s

d Providing & fixing writing stand of size 4’-0” x 1’-0” x 1’ -7½” high (Face area) as per design drg.

1 no.

e Providing & fixing Cheque drop box & complaint box of size 9” x 18” as per detail.

2 No’s.

f Providing & fixing notice board of size 2’-6” x 4’-0” 2 No’s. g Vertical Blinds Providing and fixing perforated

vertical blinds ( mettalic of luxflex ( Trac / vista / Mac make of approved colours ( 50mm / 89 mm width) complete in all respects for manager's cabin glazing and front side windows. ( basic rate of fabric shall not be less than Rs 90/- per mtr.)of 100 mm thick vertical blinds with necessary accessories like channel,string ,control unit ,fabric etc complete

20 Sqft.

18

h Providing & fixing ELECTRICAL PANEL BOXING upto ceiling ht and depth as per size of the electrical panel, layout plan made up of 19mm commercial board of CENTURY/ BHUTAN TUFF Make and finished with 1mm thick laminate of CENTURY/ AMULYA/ GREENLAM Make, shade as approved , in side to be painted over a coat of primer and enamel paint of approved Make and color. A fix glass window should also be given to show the indicator LEDS of the panel inside. The work also includes supplying, fixing of hinges, magnetic catchers, handles, Steam Beach lipping, Glass in front of Indicators, Ventilator Grill etc complete in all respects to the complete satisfaction of the Architect.

1 no.

i COLUMN/WALL PANNELING Providing & fixing of 12mm thk. Ply from the base of the column and finishing it with the laminate of approved shade & make as per design (Over columns only)

110 sqft

j

PRINTER TABLEProviding and fixing of printer table as per layout plan, 2'-6" high working top ( As per drawing) made up of 19mm commercial board of CENTURY/ Bhutan Tuff Make, finished with 1 mm thick laminate of CENTURY/ AMULYA/ GREENLAM Make, shade as approved as per the detailed drawing . The tables shall have 2'-6" X 2'-6" table top as per approved shade and color. All exposed surfaces (such as counter front, sides, drawers and cupboard etc) must be finished with 1mm thick laminate of approved make. Tabletop shall be finished with 1mm thick laminate. The inner exposed surfaces to be painted over one coat of primer and enamel paint of approved shade.Single drawer to be provided for keeping printer accesaries . Also provide a wire manager for electric connection to the printer.

0 nos

19

k Providing and fixing 2' - 6' ht. WICKET GATE between the counters to check the movements of customers inside the restricted area. Fully paneled door shutter including the door frame made up of styles and top rail, bottom rail using 1st class hardwood, 6mm commercial ply of CENTURY/ BHUTAN TUFF Make to be fixed on both faces finished with 1 mm thick laminate of CENTURY/ MERINO/ GREENLAM/ AMULYA MICA Make. The work includes providing and fixing necessary hardware SS finish latches, butt hinges etc., steam beach beading etc. (spirit polished) as per drawings to the full satisfaction of the Architect, complete in all respects. Please note that all the 19mm thickness portion must be finished with liping/margin

17 sqft

6 a Providing and fixing Aluminum Composite Panel (ACP) comprising of 50mm x 50mm hardwood frame work, 12 mm with trap door with magnetic catch/ tower bolt arrangement, finished with enamel paint. Ply to be IS 303, BWR Grade (For inside work), Ply to be IS 710 Grade ( For external work exposed to atomsphere). (Trap door to be given only if the above item is used for shutter covering outside the ATM center.)

55 sqft

b Providing & fixing in position partition made of ACP (Aluminium Composite Panel) with framing of Aluminium Tube sections of min 1.5" x1" and 18 gauge 2'-0" C/C both ways. ACP to be in 2' wide panels or distributed equally. The panels to be fixed to the frame with 3M or equivalent adhesive. Joints to be finished with Silicon based sealant. ACP thickness of 3mm min. Aluminum foil thickness to be 0.20 mm. ACP only on the ATM side with thickness of 3mm minimum. The back side of the partition to be finished with painted 6mm ply. Alubond, Eurobond, Fujibond, Alcobond or equivalent brands to be used. ACP Door 3'X7' made of Aluminum frame.

245 sqft

A AIR CONDITIONING WORK

1 AC work 1.1 Providing and fixing for 1.5 TR Split A.C with indoor &

outdoor units + copper Stablizer for Banking hall ( comprasive with inverter technology ac all weather of Hitachi/Voltas/blue star/Daikin/Carrier)

3 EACH

20

1.2 Removing and reinstalling Split A.C with indoor & outdoor units , stablisher. (This work includes minar repair work +gas filling) .

5 EACH

1.3 Providing & fixing A.C D.P SWITCH with 4sq.m. wiring 8 each 1.4 Supply & installation of 20 mm dia. “Composite”

drain pipe of Kitec or Jindal make. 85 R.

mt.

1.5 Extra copper pipe above 3m for split units 50 R. mt.

1.6 Supply & installation of Cabling between indoor & outdoor Units

70 R. mt.

1.7 Providing and fixing M.S stand for outdoor unit 3 NO;S

A ELECTRICAL WORK

1 1 Design, Manufacture, Supplying and Commissioning Main LT Panel MS 3'-0" X 4'-0" Distribution Board of 1.6mm thick MS sheet fabricated cubicle type with Danger Notice Board indicating sign (DANGER) in English, Hindi, Pinjabi. , wall mounted fully recessed / partly recessed with dust proof hinged and lockable doors, brass cable glands for incoming and out going connections with inter connections with copper tapes /wires consists of following:-(i) A cubical having 100 Amps TPN(Before bus bar) breaking current 20KA, 100 Amps TPN Bus Bar(Copper Tinned), voltmeter, ammeter & Digital power factor meter , three indicators, C.Ts. with selector switches & backup fuses (HRC type)(ii) 100 Amps 4 Pole Heavy duty on load change over switch-1 No. (iii) 63 amps 3 phase and neutral 6 way lighting D.B. with suitable rated 6/10/16 Amps SP MCB-8 Nos(for switch board wiring)., 32/40Amp DP MCB-3 Nos.( 1 for ATM UPS i/p, 2 Spare)(iv) 63 Amps 3 phase & neutral 6 way power DB with suitable rated 32/40 Amps DP MCB-9 Nos. (7 for AC ckt 2 spare) 20 Amps SP MCB-10Nos ( 8 nos for 16A plug point each separate wiring, 1 for glow sign, 1 spare) (v) 63 Amps FP ELCB-1 Nos. for LDB & 63 Amps FP ELCB-1 No. for PDB, ELCB of 30MA having 30 m Sec. Sensitivity (Complete as per technical specifications and including earthing of each Electrical equipments)(vi) LT Panel labeling using aluminium strip for section wise load distribution (Complete as per technical specifications and including earthing of each

1 EACH

21

Electrical equipments)

2 Wiring for light points with 2x1.5sqmm and PVC insulated copper conductor wire of 650/1100 volts grade in concealed / exposed PVC pipe, including by 5 Amp piano type modular switch with MS boxes, including making all the connections, including cutting chases and making good the surfaces wherever required. (This also includes SPMCB of Main panel to switch board wiring of minimum 4 sq mm copper wire and non of the switch boards circiut wiring to be parralled. Each switch board must be fed from separate circiut wiring fromSPMCB of the Main panel)

Providing and fixing point wiring with same specs as above for 1 point controlled with one switch (for lights, ceiling fans, exhaust fans)

28 each

Providing and fixing point wiring with same specs as above but 2 points controlled with one switch

0 each

Providing and fixing point wiring with same specs as above but 3 points controlled with one switch

8 each

3.2 Wiring for 5Amp light plug points with 2x1.50+1.00 sqmm & PVC insulated copper conductor wire of 650/1100 volts grade with PVC insulated Copper earth wire in concealed / exposed PVC pipe,,including 5pin 5Amp Socket with modular switch with MS boxes with earthing the third points, including cutting chases and making good the surfaces wherever required.

14 EACH

3.3 Light Plug Point in Counter/Wall/Partition (in 5Module PVC box with plate) (5pin top 2 Socket 1 switch DIRECT)

15 EACH

4 16 Amps switch socket wiring.(Power Points) :-Wiring for Power circuit with 2x4 sqmm + 1x1.5 sqmm earth wire.

4.1 Wiring for 16Amp (Socket board 2 no. 16A, 6-pin socket with 2 nos 16A switch) power plug points with 2x4+1.50 sqmm PVC insulated copper conductor wire of 650/1100 volts grade with PVC insulated copper earth wire in concealed / CONCEALED PVC pipe, ,including 2 no. 6pin 16Amp Socket with2 no. 16Amp modular switch with MS boxes with with earthing the third points, including cutting chases and making good the surfaces wherever required. There must be separate circuit wiring for each point & this circiut wiring must not be parralled/looped with switch

8 EACH

22

board of light/plug points. (Location: Pantry, water cooler, Manager cabin-1nos , Cash cabin-1no, for each two counter one 16A plug point for winter ) THIS POINT MUST BE PROVIDED ON THE WALL NOT ON THE WORKING COUNTERS

5 Fan

5.1 Exhaust fan- Supply fixing and installing the 300 mm diameter single phase 230 volt AC exhaust fan for toilets complete with motor, capacitor fan assembly mounting and frame & louvers. (2 nos in toilets and 1 nos in UPS room)

3 EACH

5.2 Ceiling fan:- Supply, fixing and installing the 56 inch diameter, 3 blade, 230 VAC, 50 Hz ceiling fan complete with the motor, starting capacitor, fan assembly, hang pipe, domes,(top & bottom) Regulator, Rubber bush, required hardwares etc. The work involved the assembly testing, installation from ceiling, connecting & commissioning of the fan at site. (Make Khaitan / Crompton Greaves)

2 EACH

5.3 Wall Fan :- 400mm sweep , oscillating type, 3-speed pull control , single piece type propeller Wall/Brackets fan (Supply & Fixing) (Make Khaitan / Crompton Greaves) 4 wall fans must be on UPS.

9 EACH

7 7 Call-bell point wiring including Ding-dong bell with 1.5 sqmm multi strand PVC copper wire including plate switches for Manager Cabin, & Outside Main Gate.

1 EACH

8 FIXTURE: Lighting Fixture Supply & Installation: Supply, unpacking, assembling, testing, fixing, connecting and commissioning the following luminaries required for internal wiring of the bank premises complete in all respect.

8.1 Providing & fixing 36w LED of CROMPTON GREAVES/PHILIPS/CRAB TREE. 4 lights must be on UPS supply

12 No.’s

8.2 Providing and fixing LED BOX TYPE TUBE (16W) fittings 4'-0" long CROMPTON GREAVES/PHILIPS/CRAB TREE.

4 No.’s

8.3 Providing & fixing LED Downlighter 12W LED 'Crom-Plus-Round' (LCDN-12-CDN) of CROMPTON GREAVES/PHILIPS/CRAB TREE. 4 Lights must be on UPS Supply

25 No.’s

8.4 1x12WCFL lamp complete with jumbo holders wipro make in toilet/UPS room including all necessary fitting and wiring (Toilets, Pantry and UPS area)

3 EACH

23

9 Telephone Points:

9.1 Providing & Fixing of PVC conduit in wall & floor including Telephone wire, M.S. box and two pin telephone sockets or R.J. – 11 plates outlet including testing, commissioning etc. as required.

16 No.’s

9.2 Lockable MDF (50 Pair) for Telephone/Lease & ISDN line . This MDF must be installed at the Branch entrance location and all the telephone line should start from this MDF.

1 JOB

10 UPS POINT (Set of 6 Amp. 4 sockets & 4 switches)

10.1 Wiring for UPS points with 2x2.50 +1x1.5 sqmm PVC insulated copper conductor wire of 650/1100 volts grade with required earth wire with concealed / exposed PVC pipe, including making all the connections, including cutting chases and making good the surfaces wherever required.including the cost of computer socket board,with 3nos 5Amp 5 pin sockets with1no. 5Amp switch 1no.fuse and 1 no. light indicator with modular swithboard. (max. two points on each circuit, Circuit shall not be paid extra, However cash cabin point & Router point should be indepently fed from single SPMCB of UPS DB )

25 EACH

10.2 6 way Double-Door TPN Distribution Boardfor UPS supply fitted with:-i. 63 Amps TPN ELCB -1No. (To be installed in the Main Panel from where UPS DB wire to be derived up to selector switch)ii. 63 Amps DPMCB -2 Nos. for UPS input supply including ups PANEL input wiring of minimum 6sqmm copper wire of phase, neutral & Earth wiring from main panel to i/p DPMCB iii. 32 Amps DPMCB -1 Nos. for UPS output iv. 6/10 Amps SPMCB - 10'Nos.

1 EACH

11 EARTHING SYSTEM:

11.1 Supplying and installation (Testing, connection & commissioning with 10 SWGearth wire) of earth stations for computers and ATM separately.

3 No.’s

12 CABLES

12.1 Providing & installation of electrical cable 40 sq. mm main cable from main to meter and meter to Electrical panel

30 MTR

12.2 P/F generator wire 35mm 4- core Alum. Cable. 30 MTR

Providing & installation of electrical cable (10 sq. mm.) from U.P.S to A.T.M. machine room.

25 MTR

24

13 Glow Sign Board pt. Wiring:- 2 x 4 sqmm + 1 x1.5sqmm multi strand PVC copper wire in PVC Pipes. This is to connected to one of SP or DP MCB of the Main Panel.

1 Nos

14 Four Pole ICTP Switch with three fuses of 100 A (Before main panel) for receiving 3 Phase & Neutral Supply100 Amps(Main Supply PSEB) To be installed at suitable location(Not to be installed in open space)

1 EACH

15 FOR ATM UPS INPUT POINT at ATM ups location(in form of 2 nos of mettalic socket plug point with 2 nos 32Amp SPMCB): Wiring for connecting 2x2KVA ATM UPS with 2x6+4 sqmm PVC insulated copper conductor wire of 650/1100 volts grade with PVC insulated copper earth wire in concealed / exposed PVC pipe, including Concealed Industrial Metallic Socket with 2x32Amp SP MCB housed in MS sheet box with PVC insulated Copper earth wire. Work is also including circuit wiring & cutting chases and making good the surfaces wherever required. (Circuit Shall not be paid extra)There must be two mettalic socket on one circuit wiring of 2x6+4sqm copper wiring & this circiut wiring must not be parralled/looped with switch board of light/plug points. 2x6+4sqm copper wiring should be derived from Main panel not from the UPS panel

2 NO

i) Providing, Laying, testing and commissioning CAT – VI/ Lucent / D- Link computer networking cable in PVC conduit along with sockets

16 No.’s

ii) Supplying of patch chords for computers 1m & 2m length.

16 No.’s

Signage for branch and ATM 50 sqft

Timer for Signage 1 No.s

Providing and fixing of 8 way double door TPN box for ATM controli. 63 Amps TPN MCM -1No. ii. 63 Amps DPMCB -2 Nos. iv. 6/10 Amps SPMCB - 8Nos.

1 No.s

5 kg. capacity CO2 gas type Fire extinguisher of Minimax , Ceasefire or New age make

1 No.s

Wooden Storage Cabinet made with ply, on all four sides, 4 shelves inside with wire manager slots, finished with enamel paint in interior and 1.0 mm laminate finish on exterior, appropriate slots to be made for air circulation on either sides, approximate size 610mm x 762mm x 1524mm, Size of cabinet and nos. of shelves subject to size of UPS, batteries and

1 Nos.

25

NIU.

Providing and installation of Switch timer for alternate operation between 2 aircon units. In ATM

1 Nos.

C AIR CONDITIONING WORK S.

No.

Description Quantity Unit

1 AC work 1.1 Providing and fixing for 1.5 TR Split A.C with indoor & outdoor

units + copper Stablizer for Banking hall ( comprasive with inverter technology ac all weather of Hitachi/Voltas/blue star/Daikin/Carrier)

3 EACH

1.2 Removing and reinstalling Split A.C with indoor & outdoor units , stablisher. (This work includes minar repair work +gas filling) .

5 EACH

1.3 Providing & fixing A.C D.P SWITCH with 4sq.m. wiring 8 each 1.4 Supply & installation of 20 mm dia. “Composite” drain pipe of

Kitec or Jindal make. 85 R.

mt.

1.5 Extra copper pipe above 3m for split units 50 R. mt.

1.6 Supply & installation of Cabling between indoor & outdoor Units 70 R. mt.

1.7 Providing and fixing M.S stand for outdoor unit 3 NO;S