valve technical data sheet high temperature bellows … · 2020. 9. 29. · bellows sealed valve -...

• T: +44 161 9333933 • [email protected] • T: +1 562 7334634 • [email protected]

VALVE TECHNICAL DATA SHEET HIGH TEMPERATURE BELLOWS SEALED VALVE

SERIES 4

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection.

ASME III option available. Straight Pattern shown, also available as Angle pattern and Oblique pattern.Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions

Valve Size Dim Dim Dim Weight Cv DN A mm B mm C mm Kg IGPM

DN8 108 241 100 9 1.7 DN15 108 241 100 9 2.45 DN20 117 241 100 9 2.45 DN25 127 254 100 9.6 5.8

DN40 165 368 150 24 12.4 DN50 203 400 150 25 18.5

Material Specification

Body Bonnet Seat Disk Stem Bellows Back up Gland Yoke Bush

Stainless Steel Valve St.St. ASTM A182 F316H St.St. ASTM A182 F316H Integral Hard Faced St. St. - Hard Faced St.St. ASTM A182 F316H Incolloy 800H or 800HT Exfoliated Graphite Aluminium

Service Service Temperature Pressure

ºC bar g 38 103.4 50 101.6

100 94.2 200 79.6 300 70.6 400 65.7 500 63.4 600 49.8 700 22.8 800 8.8 816 7.2

ValveDatasheet

1

Date Issued: Sept. 2020

Date Issued: Sept. 2020Part of Dynamic Controls Ltd

BELLOWS SEALED CARTRIDGE VALVE – MANIFOLD Series 34

Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available. Valve can be supplied with actuation - Electric or Pneu- matic plus controls. Extended spindle versions also available. Manifold Block designed to suit requirements, distribution blocks, double block and bleed, reducing stations. Valve type and numbers to suit requirements.

Cartridge Valve, seat and all seals are removed with the top assembly. This leaves only body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Suitable for High/Low Temperature / Extreme duties Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperature upto 700ºC. Materials can be changed to customer specifications.

3 Valve 6 Valve Distribution Block

Distribution Block

Material Specification Body Bonnet Seat Seat Seal Disk Stem Bellows Back up Gland

St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182 F304L St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182 F304L St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L Perlast or Kalrez or Stainless Steel Seal St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L St.St. Type 316L Graphite

Valve Datasheet

2



Part of Dynamic Controls Ltd

Class 600 Bellows Sealed Globe Valve, Conven- tional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available Valve can be supplied with actuation - Electric or Pneumatic plus controls. Extended spindles alao available Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection or Manifold blocks

Cartridge Valve, seat and all seals are removed with the top assembly. This leaves only body left in line. Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperature upto 608ºF. Materials can be changed to customer specifications.

Dimensions Valve Size

DN DN8/¼”

DN15/½” DN20/¾” DN25/1”

DN40/1½” DN50/2” DN80/3”

DN100/4” DN150/6”

Dim A in 4.25 ”

4.25” 4.6” 5”

6.5” 8” 14” 16”

Dim B in 9.55 ”

9.55” 9.55”

10.10” 14.5”

15.75” 19.7”

20.50”

Weight lb 19.8 19.8 19.8 21.2 52.9 55.1 445 529 613

Cv IGPM

1.7 2.45 2.45 5.8

12.4 18.5 37 76

260 Material Specification

Body Bonnet Seat Seat Seal Disk Stem Bellows Back up Gland

St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182 F304L St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182 F304L St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L Perlast or Kalrez Seal St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L St.St. Type 316L Graphite

ValveDatasheet

3

VALVE TECHNICAL DATA SHEET BELLOWS SEALED CARTRIDGE VALVE

SERIES 34

• T: +44 161 9333933 • [email protected] T: +1 562 7334634 • [email protected]

mailto:[email protected]

http://www.dynamiccontrols.co.uk/



Class 600 Bellows Sealed Globe Valve to BS5352/ANSI B16.34, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Hermetically Seal Welded Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Locking Device, Interlocks, Extended Spindle. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352. Pres- sure/Temperature rating to ANSI B16.34 differ. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions

Valve Size DN

DN8/¼” DN15/½” DN20/¾” DN25/1” DN40/1½”

Dim A in 4.25” 4.25” 4.60” 5.00” 6.50”

Dim B in 9.50” 9.50” 9.50”

10.00” 14.50”

Dim C in 3.95” 3.95” 3.95” 3.95” 5.90”

Weight lb 19.8 19.8 19.8 21.2 52.9 55.1

Cv IGP

M 1.7 2.45 2.45 5.8

12.4 18.5


Body Bonnet Seat

Disk

Stem Bellows Back up Gland Yoke Bush

Carbon Steel Valve C.St. ASTM A105C.St. ASTM A105St.St. Type 410, Type 316or Integral Stellite HFSt.St. Type 410, Type 316or Stellite HFSt. St. Type 316St. St. Type 316Exfoliated GraphiteAluminium Bronze

Stainless Steel Valve St.St. Type 316 St.St. Type 316 St.St. Type 410, Type 316 or Integral Stellite HF St.St. Type 410, Type 316 or Stellite HF St. St. Type 316 St. St. Type 316 Exfoliated Graphite Aluminium Bronze

Service Temperature

ºC -30 to +38

50100150 200 250 300 350 400 450 500

Service Pressure Bar g

99 98 96 94 91 87 79 71 63 55 34

ValveDatasheet

4

• T: +44 161 9333933 • [email protected] • T: +1 562 7334634 • ORodriguez@ cunicocorp.com

VALVE TECHNICAL DATA SHEET BELLOWS SEALED CARTRIDGE VALVE

SERIES 34





VALVE TECHNICAL DATA SHEETBELLOWS SEALED VALE

SERIES 34

Class 800 Bellows Sealed Globe Valve to BS5352, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection.

Nuclear Versions to ASME III available.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions

Valve Size DN

DN8/¼” DN15/½” DN20/¾” DN25/1” DN40/1½”

Dim A in 4.25” 4.25” 4.60” 5.00” 6.50”

Dim B in 9.50” 9.50” 9.50”

10.00” 14.50”

Dim C in 3.95” 3.95” 3.95” 3.95” 5.90”

Weight lb 19.8 19.8 19.8 21.2 52.9 55.1

Cv IGP

M 1.7 2.45 2.45 5.8

12.4 18.5


Body Bonnet Seat

Disk


Carbon Steel Valve C.St. ASTM A105C.St. ASTM A105St.St. Type 410 orIntegral Stellite HFSt.St. Type 410 orStellite HFSt. St. Type 316LSt. St. Type 316LExfoliated GraphiteAluminium Bronze

Stainless Steel Valve St.St. Type 316L St.St. Type 316L St.St. Type 410 or Integral Stellite HF St.St. Type 410 or Stellite HF St. St. Type 316L St. St. Type 316L Exfoliated Graphite Aluminium Bronze

Service Temperature

ºC -30 to +38

50100150 200 250 300 350 400 450 500

Service Pressure Bar g

99 98 96 94 91 87 79 71 63 55 34

ValveDatasheet

5





VALVE TECHNICAL DATASHEETBELLOWS SEALED VALVE - NUCLEAR

SERIES 34

Class 600 Bellows Sealed Globe Valve designed to ASME III, Conven- tional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Seal Welded Bonnet version available.

Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASME SA105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions

Valve Size DN

DN8/¼” DN15/½” DN20/¾” DN25/1” DN40/1½”

Dim A in 4.25” 4.25” 4.60” 5.00” 6.50”

Dim B in 9.50” 9.50” 9.50”

10.00” 14.50”

Dim C in 3.95” 3.95” 3.95” 3.95” 5.90”

Weight lb 19.8 19.8 19.8 21.2 52.9 55.1

Cv IGP

M 1.7 2.45 2.45 5.8

12.4 18.5


Body Bonnet Seat

Disk

Stem Bellows Back up Gland

Carbon Steel Valve C.St. ASME SA105C.St. ASME SA105St.St. ASME SA564 630or Integral Stellite HFSt.St. ASME SA564 630or Stellite HFSt. St. ASME SA479 316L St. St. Type 316Exfoliated Graphite

Stainless Steel Valve St.St. ASME SA182 316L St.St. ASME SA182 316L St.St. ASME SA564 630 or Integral Stellite HF St.St. ASME SA564 630 or Stellite HF St. St. ASME SA479 316L St. St. Type 316 Exfoliated Graphite

ValveDatasheet

6

• T: +44 161 9333933 • [email protected] •T +1 562 7334634 • [email protected]



Date Issued: Sept. 2020 Part of Dynamic Controls Ltd

Class 600 Bellows Sealed Globe Valve, Conven- tional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. To BSEN15761 or Nuclear Class to ASME III available Valve can be supplied with actuation - Electric or Pneumatic plus controls. Extended spindles alao available Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection or Manifold blocks

Cartridge Valve, seat and all seals are removed with the top assembly. This leaves only body left in line. Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperature upto 1290ºF. Materials can be changed to customer specifications.

Dimensions Valve Size

DN DN8/¼”

DN15/½” DN20/¾” DN25/1”

DN40/1½” DN50/2” DN80/3”

DN100/4” DN150/6”

Dim A in 4.25” 4.25” 4.6” 5”

6.5” 8” 14” 16”

Dim B in 9.55” 9.55” 9.55”

10.10” 14.5”

15.75” 19.7”

20.50”

Weight lb 19.8 19.8 19.8 21.2 52.9 55.1 445 529 613

Cv IGP

M 1.7 2.45 2.45 5.8

12.4 18.5 37 76

260 Material Specification

Body Bonnet Seat Seat Seal Disk Stem Bellows Back up Gland

St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182 F304L St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307)/ ASME SA182 F304L St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L Stainless Steel St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L St.St. BSEN 10088-3 1.4307/ ASME SA479 F304L St.St. Type 316L Graphite

ValveDatasheet

7


VALVE TECHNICAL DATASHEETBELLOWS SEALED CARTRIDGE VALVE - EXTREME

SERIES 4



Date Issued: Sept. 2020 Part of Dynamic Controls Ltd

Series 34 High Temperature Bellows Sealed Valve Class 600 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection. ASME III option available.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, buttweld and screwed ends to BS5352

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions

Valve Size DN

DN8/¼” DN15/½” DN20/¾” DN25/1” DN40/1½”

Dim A in 4.25” 4.25” 4.60” 5.00” 6.50”

Dim B in 9.50” 9.50” 9.50”

10.00” 14.50”

Dim C in 3.95” 3.95” 3.95” 3.95” 5.90”

Weight lb 19.8 19.8 19.8 21.2 52.9 55.1

Cv IGP

M 1.7 2.45 2.45 5.8

12.4 18.5


Body Bonnet Seat Disk Stem Bellows Back up Gland Yoke Bush

Stainless Steel Valve St.St. ASTM A182 F316H St.St. ASTM A182 F316H Integral Hard Faced St. St. - Hard Faced St.St. ASTM A182 F316H Incolloy 800H or 800HT Exfoliated Graphite Aluminium Bronze

Service Temperature

ºF 100 200 300 400 500 600 700 900

1100 1300 1500

Service Pressure psi g 1440 1240 1120 1030 955 905 865 790 645 275 85

ValveDatasheet

8


VALVE TECHNICAL DATASHEETHIGH TEMPERATURE BELLOWS SEALED VALVE

SERIES 34



Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.

Nuclear versions to ASME III available.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions (typical) Class 800 Class 900/1500

Valve Size DN

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min DN6 108 241 100 9 1.7 216 321 150 12 1.7

DN15 108 241 100 9 2.45 216 321 150 12 2.45 DN20 117 241 125 9 2.45 229 321 175 12 2.45 DN25 127 254 125 9.6 5.8 254 384 175 15 5.8 DN40 165 368 175 24 12.4 305 458 225 30 12.4 DN50 203 400 200 25 18.5 368 530 350 35 18.5

Class 800 Service

Class 800 Service

Temperature Pressure oC Bar g

-38 to +38 99 50 98

100 96 150 94 200 91 250 87 300 79 350 71 400 63 450 55 500 34

Component Material Carbon Steel Valve Stainless Steel Valve

Body C.St. ASTM A105 St.St. Type 316L Bonnet C.St. ASTM A105 St.St. Type 316L

Seat St.St. Type 410 or integral Stellite HF

St.St. Type 410 or integral Stellite HF

Disk St.St. Type 410 or Stellite HF

St.St. Type 410 or Stellite HF

Stem St.St. Type 316L St.St. Type 316L Bellows St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze

ValveDatasheet

9


VALVE TECHNICAL DATASHEETBBOLTED BONNET VALVE - STRAIGHT PATTERN

SERIES 34A




Class 600/900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks. Cartridge valve, version also available - seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve design suitable for temperatures up to 320 oC. Materials can be changed to customer specifications.

Dimensions Size Dim A Dim B Weight Cv DN mm mm Kg UKGPM 6 229 242 13 2

15 229 242 13 5.8 20 229 245 13 5.8 25 254 260 15.5 11 40 305 350 35 30 50 368 420 40 54 80 381 540 250 153 100 457 562 295 267 150 610 820 320 690

Materials Component Material

Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Seat St.St. BSEN 10088-3 1.4307 / ASME SA479 304L / HF Seat Seal Stainless steel / Graphite Disk St.St. BSEN 10088-3 1.4307 / ASME SA479 304L / HF Stem St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Bellows St.St. Type 316L Back up Gland Graphite

ValveDatasheet

10


VALVE TECHNICAL DATASHEETBOLTED BONNET VALVE - OBLIQUE PATTERN

SERIES 34B




Class 800/900/1500 bellows sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.


Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions (typical) Class 800 Class 900/1500

Valve Size DN

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min DN6 57 241 100 9 2.7 108 321 150 12 2.7

DN15 57 241 100 9 3.9 108 321 150 12 3.9 DN20 64 241 100 9 3.9 114 321 150 12 3.9 DN25 70 254 100 9.6 9.2 127 384 150 15 9.2 DN40 83 368 150 24 19.8 152 458 200 30 19.8 DN50 102 400 150 25 29.6 184 530 290 35 29.6







Stem St.St. Type 316L St.St. Type 316L Bellows St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze

ValveDatasheet

11

• T: +44 161 9333933 • [email protected] T: +1 562 7334634 • ORodriguez@ cunicocorp.com

VALVE TECHNICAL DATASHEETBOLTED BONNET VALVE - ANGLE PATTERN

SERIES 34C




Seal Welded Bonnet Valve - Straight Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet. To ANSI B16.34 or Nuclear Class to ASME III

Available with Integral Hard Faced (Stellite 6 or Colomonoy 5) Seat or Screwed in Stainless Steel Seat

Valve can be supplied with Actuator - Electric or Pneumatic.

Buttweld end connections shown, also available as screwed, socket weld, flanged or special connection

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media. DN65/DN80/DN100 normally cast body and bonnet. Forged available.

Dimensions (typical) Class 150/300/600 Class 900/1500

Valve Size DN

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min DN6 165 243 100 16 1.0 216 261 150 12 1.0

DN15 165 243 100 16 1.8 216 261 150 12 1.6 DN20 190 243 100 16 4.0 229 261 150 12 2.9 DN25 216 256 125 20 6.9 254 294 150 14 5.0 DN40 241 368 150 33 17.4 305 398 200 28 14.5 DN50 292 400 200 39 31.0 368 440 250 30 23.0 DN65 330 450 300 220 46.0 419 500 300 180 37.0 DN80 356 500 300 260 70.0 381/470 560 300 200 62.0

DN100 432 521 300 350 128.0 457/546 590 300 290 113.0

Dimensions are subject to confirmation. Drawings with confirmed dimensions can be supplied at time of order.

Material Specification Carbon Steel Valve Stainless Steel Valve

Body & Bonnet

C.St. ASME SA350 LF2 orC.St. ASME SA352 LCB

St.St. ASME SA182 F316L or St.St. ASME SA351 CF3M

Seat Integral Hard Facing Integral Hard Facing Disk St.St. Type 316L with Hard Facing St.St. Type 316L with Hard Facing Stem St. St. ASME SA564 630 H1075 St. St. ASME SA564 630 H1075 Bellows Inconel 600/625 Inconel 600/625 Gland Exfoliated Graphite Exfoliated Graphite Bush Aluminium Bronze Aluminium Bronze

ValveDatasheet

12

• T: +44 161 9333933 • [email protected] T: +1 562 7334634 • [email protected]

VALVE TECHNICAL DATASHEETSEAL WELDED BONNET VALVE - STRAIGHT PATTERN

SERIES 35A




Seal Welded Bonnet Valve - Oblique Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet.

Available with Integral Hard Faced Seat to offer increased resistance against corrosion.



Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials.

Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352.

Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.


Temperature Pressure oC Bar g

-30 to 38 99 50 98

100 96 150 94 200 91 250 87 300 79 350 71 400 63 450 55 500 34

Dimensions (typical) Class 800

Valve Size DN

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min DN8 154 210 95 9 4.4

DN15 154 210 95 10 4.4 DN20 154 210 95 11 4.4 DN25 154 210 95 11 9.1 DN40 224 325 165 24 27.5 DN50 274 325 130 25 40


Body & Bonnet C.St. ASTM A105 St.St. BS1503 304S11

Seat St.St. Type 410 or Integral Stellite Hard Facing

St.St. Type 410 or Integral Stellite Hard Facing

Disk St.St. Type 410 or Stellite Hard Facing

St.St. Type 410 or Stellite Hard Facing

Stem St. St. Type 304 St. St. Type 304 Bellows St. St. Type 304 St. St. Type 304 Gland Exfoliated Graphite Exfoliated Graphite Bush Aluminium Bronze Aluminium Bronze

ValveDatasheet

13


VALVE TECHNICAL DATASHEETSEAL WELDED BONNET VALVE - OBLIQUE PATTERN

SERIES 3AB




Seal Welded Bonnet Valve - Angle Pattern. Standard Bore, Outside Screw and Yoke, Non-rising handwheel, Seal Welded Bonnet. To ANSI B16.34 or Nuclear Class to ASME III

Available with Integral Hard Faced (Stellite 6 or Colomonoy 5) Seat or Screwed in Stainless Steel Seat



Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425ºC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media. DN65/DN80/DN100 normally cast body and bonnet. Forged available.

Dimensions (typical) Class 150/300/600 Class 900/1500

Valve Size DN

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min

Dim A mm

Dim B mm

Dim C mm

Weight Kg

Cv UK

Gal/min DN6 57 243 100 16 2.7 108 261 150 12 2.7

DN15 57 243 100 16 3.9 108 261 150 12 3.9 DN20 64 243 100 16 3.9 114 261 150 12 3.9 DN25 70 256 125 20 9.2 127 294 150 14 9.2 DN40 83 368 150 33 19.8 152 398 200 28 19.8 DN50 102 400 200 39 29.6 184 440 250 30 29.6 DN65 108 450 300 220 73 210 500 300 180 60 DN80 121 500 300 260 110 235 560 300 200 100

DN100 146 521 300 350 204 273 590 300 290 180



Body & Bonnet

C.St. ASME SA350 LF2 orC.St. ASME SA352 LCB

St.St. ASME SA182 F316L or St.St. ASME SA351 CF3M

Seat Integral Hard Facing Integral Hard Facing Disk St.St. Type 316L with Hard Facing St.St. Type 316L with Hard Facing Stem St. St. ASME SA564 630 H1075 St. St. ASME SA564 630 H1075 Bellows Inconel 600/625 Inconel 600/625 Gland Exfoliated Graphite Exfoliated Graphite Bush Aluminium Bronze Aluminium Bronze

Valve Datasheet 14


VALVE TECHNICAL DATASHEETSEAL WELDED BONNET VALVE - ANGLE PATTERN

SERIES 35C




Class 900/1500 bellows sealed globe valve, standard bore, outside screw and yoke, bolted and lip-seal welded bonnet. ASME III option available. Secondary gland in the event of bellows failure. Available with integral hard faced seat to offer increased resistance against erosion Valve can be supplied with manual operation or actuated - electric or pneumatic. Manual valve and electrically actuated valve shown.

Valve shown is with a leak detection port, to provide early warning of any bellows failure. Extended spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically actuated valves are available.

Class 900 Manually Operated Electrically Operated

Size Dim A Dim B Weight Dim D Dim E Weight Cv DN mm mm Kg mm mm Kg UKGPM

6 216 320 13.8 520 216

Please ask for details

1.0 15 216 320 13.8 520 216 1.8 20 229 320 13.8 520 229 4.0 25 254 320 13.8 520 254 6.9 40 305 382 24.1 570 305 17.4 50 368 406 46.8 595 368 31.0 65 419 406 46.8 595 419 46.0 80 381 548 97.7 730 381 70.0

100 457 579 183 755 457 128.0

Component Material

316 Stainless Steel

304 Stainless Steel

Body St.St. ASME SA182 F316

St.St. ASME SA182 F304

Bonnet St.St. ASME SA182 F316


Seat

St.St. ASME SA479 316 or integral Stellite hard faced


Disk

St.St. ASME SA479 316 or St.St. Type 316 hard faced


Stem St.St. ASME SA479 316

St.St. ASME SA479 304

Bellows St.St. Type 316/316L

St.St. Type 316/316L

Back up Gland

Exfoliated graphite

Exfoliated graphite

Yoke Bush Aluminium bronze

Aluminium bronze



6 216 305 17.2 TBA 216


1.0 15 216 305 17.2 TBA 216 1.6 20 229 305 18.6 TBA 229 2.9 25 254 311 19.5 TBA 254 5.0 40 305 345 28.1 TBA 305 14.5 50 368 371 76.2 TBA 368 23.0 65 419 400 80.3 TBA 419 37.0 80 381 508 137 TBA 381 62.0

100 457 577 231 TBA 457 113.0

Valve Datasheet

15



SERIES 35C








6 288 245 13.8 551 288


7 15 288 245 13.8 551 288 7 20 288 245 13.8 551 288 12.9 25 288 245 13.8 551 288 20.8 40 323 293 24.1 585 323 39 50 407 311 46.8 605 407 92 65 407 311 46.8 605 407 125 80 437 420 97.7 742 437 213

100 427 443 183 775 427 260

Component Material

316 Stainless Steel

304 Stainless Steel





Seat



Disk







Back up Gland

Exfoliated graphite

Exfoliated graphite


Aluminium bronze



6 323 305 17.2 TBA 323


7 15 323 305 17.2 TBA 323 7 20 323 305 18.6 TBA 323 12.9 25 407 311 19.5 TBA 407 20.8 40 407 345 28.1 TBA 407 39 50 437 371 76.2 TBA 437 92 65 437 400 80.3 TBA 437 125 80 508 508 137 TBA 508 213

100 508 577 231 TBA 508 260

Valve Datasheet

16



SERIES 35C








6 108 320 13.8 520 108


7 15 108 320 13.8 520 108 7 20 114 320 13.8 520 114 12.9 25 127 320 13.8 520 127 20.8 40 152 382 24.1 570 152 39 50 184 406 46.8 595 184 92 65 210 406 46.8 595 210 125 80 190 548 97.7 730 190 213

100 229 579 183 755 229 260

Component Material

316 Stainless Steel

304 Stainless Steel





Seat



Disk







Back up Gland

Exfoliated graphite

Exfoliated graphite


Aluminium bronze



6 108 305 17.2 TBA 108


7 15 108 305 17.2 TBA 108 7 20 114 305 18.6 TBA 114 12.9 25 127 311 19.5 TBA 127 20.8 40 152 345 28.1 TBA 152 39 50 184 371 76.2 TBA 184 92 65 210 400 80.3 TBA 210 125 80 235 508 137 TBA 235 213

100 273 577 231 TBA 273 260

Valve Datasheet

17


VALVE TECHNICAL DATASHEETBOLTED/EDGE BONNET VALVE - ANGLE PATTERN

SERIES 36C




• T: +44 161 633 3933 • [email protected] • T: +1 562 7334634 • [email protected]

CARTRIDGE VALVE TECHNICAL DATA SHEET BELLOWS SEALED STOP AND STOP/CHECK VALVE SERIES 40A

103.4 Bar 1500 psi (Class 600)

Replaceable Cartridge

Forged Valve Body

Technical Data

Working Pressure 103.4 Bar / 1500 psi Working Temperature Min –20ºC/-4ºF - Application Medium •Air •Oil •Gas •WaterQuality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1 Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622 Hydrostatic Test 156 Bar / 2262psi Valve Closure Test 114 Bar / 1653psi Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1 Leakage Class Bubble Tight as per ANSI Class VI Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel

type A105 or Monel Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44 or Monel Bellows Material Stainless Steel type 316L, Inconel 600/625 Seals Material Perlast / Kalrez Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel or PEEK Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel Handwheel Material Aluminum, Stainless Steel or Iron

Connection Type Cartridge flanged to housing. Housing socket weld ends, buttweld ends or flanged

OVERALL DIMENSIONS (CARTRIDGE AND VALVE BODY) Product

Designation Estimated

Weight Pipe Size Cv UK Gal/min / US Gal/min

A (mm/ins)

B (mm/ins)

C (mm/ins)

S40A-15 7Kg/15.5lbs DN15 / 1/2” 2.45 / 2.94 108 / 4.26” 214 / 8.43” 108 / 4.26” S40A-20 7Kg/15.5lbs DN20 / 3/4” 2.45 / 2.94 117 / 4.61” 214 / 8.43” 108 / 4.26” S40A-25 8Kg/17.6lbs DN25 / 1” 5.8 / 6.96 127 / 5” 225 / 8.86” 108 / 4.26” S40A-40 17Kg/37.5lbs DN40 / 1 ½” 12.4 / 14.9 165 / 6.5” 340 / 13.39” 115 / 4.53” S40A-50 22Kg/48.5lbs DN50 / 2” 18.5 / 22.2 203 / 8” 350 / 13.78” 115 / 4.53” S40A-80 62Kg/136.7lbs DN80 / 3” 37 / 44.4 318 / 12.52” 500 / 19.59” 142 / 5.59” S40A-100 120Kg/264.5lbs DN100 / 4” 76 / 91.2 406 / 15.99” 521 / 20.52” 180 / 7.09” S40A-150 170Kg/374.8lbs DN150 / 6” 260 / 312 559 / 22” 780 / 30.71 220 / 8.66” Data sheet S40A, Date 30th July 2020

Valve Datasheet

18

Applications Submarines

Nuclear Power Stations

- Max 326ºC/619ºF

DEF STAN 02-375 and ANSI B16.34 Design Specification

claudia.madrigal2

Line


CARTRIDGE VALVE TECHNICAL DATA SHEET BELLOWS SEALED STOP AND STOP/CHECK VALVE SERIES 40B

103.4 Bar 1500 psi (Class 600)


Forged Valve Body

Technical Data

Working Temperature Min –20ºC/-4ºF - - Max 326ºC/619ºF Applications Medium •Air •Oil •Gas •WaterQuality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1 Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622 Hydrostatic Test 156 Bar / 2262psi Valve Closure Test 114 Bar / 1653psi Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1 Leakage Class Bubble Tight as per ANSI Class VI Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel

type A105 or Monel Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44 or Monel Bellows Material Stainless Steel type 316L, Inconel 600/625 Seals Material Perlast / Kalrez Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel or PEEK Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel Handwheel Material Aluminum, Stainless Steel or Iron





A (mm/ins)

B (mm/ins)

C (mm/ins)

S40B-15 7Kg/15.5lbs DN15 / 1/2” 5.8 / 6.96 165 / 6.5” 180 / 7.09” 86 / 3.39” S40B-20 7Kg/15.5lbs DN20 / 3/4” 5.8 / 6.96 190 / 7.48” 180 / 7.09” 86 / 3.39” S40B-25 8Kg/17.6lbs DN25 / 1” 11 / 13.2 216 / 8.5” 190 / 7.48” 86 / 3.39” S40B-40 19Kg/41.9lbs DN40 / 1 ½” 30 / 36 241 / 9.49” 260 / 10.24” 137 / 5.39” S40B-50 22Kg/48.5lbs DN50 / 2” 54 / 64.8 292 / 11.5” 280 / 11.02” 137 / 5.39” S40B-80 62Kg/136.7lbs DN80 / 3” 149 / 178.8 356 / 14.02” 432 / 17” 180 / 7.09” S40B-100 110Kg/242.5lbs DN100 / 4” 220 / 264 356 / 14.02” 502 / 19.76” 180 / 7.09” S40B-150 190Kg/418.9lbs DN150 / 6” 550 / 660 435 / 17.13” 780 / 30.71 220 / 8.66”

Data sheet S40B, Date 30th July 2020

Valve Datasheet

19

Submarines

Nuclear Power Stations Applications

Design Specification DEF STAN 02-375 and ANSI B16.34 Working Pressure 103.4 Bar / 1500 psi

claudia.madrigal2

Line

Bellows Sealed Angle Pattern Globe Valve, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. To BSEN15761 or nuclear class to ASME III available. Valve can be supplied with actuation - electric or pneumatic plus controls. Extended spindles also available. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection or manifold blocks. Cartridge valve, seat and all seals are removed with the top assembly. This leaves only the body left in line. Maintenance time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted. Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Valve seals suitable for temperatures up to 320 oC. Materials can be changed to customer specifications.

Dimensions Size Dim A Dim B Dim C Dim D Dim E Weight DN mm mm mm mm mm Kg 8 45 200 32 101 102 8

15 57 218 32 101 102 12 20 64 230 32 101 102 12 25 70 230 32 127 102 12 40 83 235 43 155 128 21 50 102 255 51 155 165 26 80 178 482 104 254 220 202

100 203 502 114 254 240 275 150 279 770 139 450 278 355

Component Material Body St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Bonnet St.St. BSEN 10222-5 x2 CrNi 18-9 (1.4307) / ASME SA182 F304L Seat St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Seat Seal Perlast or Kalrez seal Disk St.St. BSEN 10088-3 1.4307 / ASME SA479 304L Stem St.St. BSEN 10088-3 1.4307 Bellows St.St. Type 316L Back up Gland Graphite

Valve

Datasheet 20


VALVE TECHNICAL DATASHEETBOLTED BONNET CARTRIDGE VALVE - ANGLE PATTERN

SERIES 40C





CARTRDIGE VALVE TECHNICAL DATA SHEET STOP AND STOP/CHECK VALVE SERIES 50A

103.4 Bar 1500 psi (Class 600)


Forged Valve Body

Technical Data

103.4 Bar / 1500 psi Working Temperature Min –20ºC/-4ºF - - Max 326ºC/619ºF

Application Medium Air •Oil •Gas •Water Quality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1 Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622 Hydrostatic Test 156 Bar / 2262psi Valve Closure Test 114 Bar / 1653psi Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1 Leakage Class Bubble Tight as per ANSI Class VI Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel

type A105, Monel or Ni Al Br DEF STAN 02-833 pt2 Main Cartridge Components Material Stainless Steel type 316L, Super Austenitic type F44, Monel or Ni Al Br Seals Material Perlast / Kalrez Seat Material Stainless Steel type 316L, Super Austenitic type F44, Monel, PEEK or Ni

Al Br Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel Handwheel Material Aluminum, Stainless Steel or Iron





A (mm/ins)

B (mm/ins)

C (mm/ins)

S50A-15 5Kg/11lbs DN15 / 1/2” 2.45 / 2.94 108 / 4.26” 171 / 6.73” 108 / 4.26” S50A-20 7Kg/15.5lbs DN20 / 3/4” 2.45 / 2.94 117 / 4.61” 171 / 6.73” 108 / 4.26” S50A-25 8Kg/17.6lbs DN25 / 1” 5.8 / 6.96 127 / 5” 185 / 7.28” 108 / 4.26” S50A-40 10Kg/22lbs DN40 / 1 ½” 12.4 / 14.9 165 / 6.5” 190 / 7.48” 115 / 4.53” S50A-50 16.5Kg/36.4lbs DN50 / 2” 18.5 / 22.2 203 / 8” 250 / 9.84” 115 / 4.53” S50A-80 56Kg/123.4lbs DN80 / 3” 37 / 44.4 318 / 12.52” 340 / 13.4” 142 / 5.59” S50A-100 90Kg/198.5lbs DN100 / 4” 76 / 91.2 406 / 15.99” 370 / 13.57” 180 / 7.09” S50A-150 140Kg/308.6lbs DN150 / 6” 260 / 312 559 / 22” 540 / 21.26” 220 / 8.66”

Data sheet S50A, Date 30th July 2020

Valve Datasheet

21



Design Specification DEF STAN 02-375 and ANSI B16.34 Working Pressure

claudia.madrigal2

Line


CARTRIDGE VALVE TECHNICAL DATA SHEET STOP AND STOP/CHECK VALVE SERIES 50B

103.4 Bar 1500 psi (Class 600)


Forged Valve Body

Technical Data Design Specification DEF STAN 02-375 and ANSI B16.34 Working Pressure Working Temperature Min –20ºC/-4ºF - - Max 326ºC/619ºF

Application Medium •Air •Oil •Gas •WaterQuality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1 Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622 Hydrostatic Test 156 Bar / 2262psi Valve Closure Test 114 Bar / 1653psi Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1 Leakage Class Bubble Tight as per ANSI Class VI Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel


Al Br Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel Handwheel Material Aluminum, Stainless Steel or Iron





A (mm/ins)

B (mm/ins)

C (mm/ins)

S50B-15 6Kg/13.2lbs DN15 / 1/2” 5.8 / 6.96 165 / 6.5” 160 / 6.3” 86 / 3.39” S50B-20 6Kg/13.2lbs DN20 / 3/4” 5.8 / 6.96 190 / 7.48” 160 / 6.3” 86 / 3.39” S50B-25 8.6Kg/18.9lbs DN25 / 1” 11 / 13.2 216 / 8.5” 160 / 6.3” 86 / 3.39” S50B-40 12Kg/26.4lbs DN40 / 1 ½” 30 / 36 241 / 9.49” 220 / 8.66” 137 / 5.39” S50B-50 17Kg/37.4lbs DN50 / 2” 54 / 64.8 292 / 11.5” 235 / 9.25” 137 / 5.39” S50B-80 45Kg/99lbs DN80 / 3” 149 / 178.8 356 / 14.02” 375 / 14.76” 180 / 7.09” S50B-100 80Kg/176lbs DN100 / 4” 220 / 264 356 / 14.02” 395 / 15.55” 180 / 7.09” S50B-150 155Kg/341lbs DN150 / 6” 550 / 660 435 / 17.13” 480 / 18.9” 220 / 8.66”

Data sheet S50B, Date 30th July 2020

Valve Datasheet

22



103.4 Bar / 1500 psi

claudia.madrigal2

Line

Angle Pattern Globe Class 800 gland sealed globe valve to BS5352, standard bore, outside screw and yoke, non-rising handwheel, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Valve can be supplied with actuator - electric or pneumatic. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.



Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions Size Dim A Dim B Dim C Weight Cv DN mm mm mm Kg UKGPM 6 57 241 100 9 2.7

15 57 241 100 9 3.9 20 64 241 100 9 3.9 25 70 254 100 9.6 9.2 40 83 368 150 24 19.8 50 102 400 150 25 29.6







Stem St.St. Type 316L St.St. Type 316L Back up Gland Exfoliated graphite Exfoliated graphite Yoke Bush Aluminium bronze Aluminium bronze

Valve

Datasheet 23


VALVE TECHNICAL DATASHEETNON-BELLOWS SEALED VALVE - ANGLE PATTERN GLOBE

SERIES 50C




Class 800 non-return valve to BS5352, standard bore, bolted bonnet. Available with integral hard faced seat or screwed in stainless steel seat. Butt weld end connections shown, also available as screwed, socket weld, flanged or special connection.

Maximum pressure / temperature ratings are restricted by the valve end connections and the body / bonnet materials. Shown are the maximum ratings for socket weld, butt weld and screwed ends to BS5352. Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie. C.St. ASTM A105 is not recommended for use above 425 oC. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Service Service Temperature Pressure

oC Bar g -38 to +38 99

50 98 100 96 150 94 200 91 250 87 300 79 350 71 400 63 450 55 500 34

Dimensions Size Dim A Dim B Weight Cv DN mm mm Kg UKGPM 6 108 170 3 1.7

15 108 170 3 2.45 20 117 190 3 2.45 25 127 190 4.5 5.8 40 165 220 12 12.4 50 203 400 15 18.5


Body C.St. ASTM A105 St.St. BS1503 304S11 Bonnet C.St. ASTM A105 St.St. BS1503 304S11





Valve

Datasheet 24


VALVE TECHNICAL DATASHEETNON-BELLOWS SEALED VALVE -

STRAIGHT PATTERN NON-RETURNSERIES 50D





CARTRIDGE VALVE TECHNICAL DATA SHEET CHECK VALVE SERIES 50D1 103.4 Bar 1500 psi (Class 600)


Forged Valve Body

Technical Data

103.4 Bar / 1500 psi Working Temperature Min –20ºC/-4ºF - - Max 326ºC/619ºF Application Medium •Air •Oil •Gas •WaterQuality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1 Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622 Hydrostatic Test 156 Bar / 2262psi Valve Closure Test 114 Bar / 1653psi Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1 Leakage Class Bubble Tight as per ANSI Class VI Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel


Al Br Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel





A (mm/ins)

B (mm/ins)

C (mm/ins)

S50D1-15 5Kg/11lbs DN15 / 1/2” 2.45 / 2.94 108 / 4.26” 128 / 5.04” 108 / 4.26” S50D1-20 7Kg/15.5lbs DN20 / 3/4” 2.45 / 2.94 117 / 4.61” 171 / 6.73” 108 / 4.26” S50D1-25 8Kg/17.6lbs DN25 / 1” 5.8 / 6.96 127 / 5” 185 / 7.28” 108 / 4.26” S50D1-40 10Kg/22lbs DN40 / 1 ½” 12.4 / 14.9 165 / 6.5” 126 / 4.96” 115 / 4.53” S50D1-50 16.5Kg/36.4lbs DN50 / 2” 18.5 / 22.2 203 / 8” 207 / 8.15” 115 / 4.53” S50D1-80 46Kg/101lbs DN80 / 3” 37 / 44.4 318 / 12.52” 225 / 8.86” 142 / 5.59” S50D1-100 55Kg/121lbs DN100 / 4” 76 / 91.2 406 / 15.99” 208 / 8.19” 180 / 7.09” S50D1-150 95Kg/209lbs DN150 / 6” 260 / 312 559 / 22” 320 / 12.6” 220 / 8.66”

Data sheet S50D1, Date 30th July 2020

Valve Datasheet

25

Applications

Submarines


Design Specification DEF STAN 02-375 and ANSI B16.34 Working Pressure

claudia.madrigal2

Line


CARTRIDGE VALVE TECHNICAL DATA SHEET CHECK VALVE SERIES 50D2 103.4 Bar 1500 psi (Class 600)


Forged Valve Body

Technical Data

Working Temperature Min –20ºC/-4ºF - - Max 326ºC/619ºF

Application Medium Air •Oil •Gas •Water Quality Assurance Level EN 10204, 3.1b also Full traceability – MIC Level 1 Cleaning TP102, Oxygen cleaning to MIL-STD-1330 or MIL-STD-1622 Hydrostatic Test 156 Bar / 2262psi Valve Closure Test 114 Bar / 1653psi Shock Qualification To be verified by test to customer’s requirements e.g. MIL-S-901D Vibration Qualification To be verified by test to customer’s requirements e.g. MIL-STD-167-1 Leakage Class Bubble Tight as per ANSI Class VI Valve Body Material Forged Stainless Steel type 316L, Super Austenitic type F44, Carbon Steel


Al Br Nuts/Studs Material Stainless Steel NES 862/ASME 194/ASTM A193/ MIL-S-1222/Monel





A (mm/ins)

B (mm/ins)

C (mm/ins)

S50D2-15 6Kg/13.2lbs DN15 / 1/2” 5.8 / 6.96 165 / 6.5” 100 / 3.94” 86 / 3.39” S50D2-20 6Kg/13.2lbs DN20 / 3/4” 5.8 / 6.96 190 / 7.48” 100 / 3.94” 86 / 3.39” S50D2-25 8.6Kg/18.9lbs DN25 / 1” 11 / 13.2 216 / 8.5” 100 / 3.94” 86 / 3.39” S50D2-40 12Kg/26.4lbs DN40 / 1 ½” 30 / 36 241 / 9.49” 130 / 5.12” 137 / 5.39” S50D2-50 17Kg/37.4lbs DN50 / 2” 54 / 64.8 292 / 11.5” 160 / 6.3” 137 / 5.39” S50D2-80 45Kg/99lbs DN80 / 3” 149 / 178.8 356 / 14.02” 270 / 10.63” 180 / 7.09” S50D2-100 60Kg/132lbs DN100 / 4” 220 / 264 356 / 14.02” 310 / 12.2” 180 / 7.09” S50D2-150 100Kg/220lbs DN150 / 6” 550 / 660 435 / 17.13” 370 / 14.6” 220 / 8.66”

Data sheet S50D2, Date 30th July 2020

Valve Datasheet

26



Design Specification DEF STAN 02-375 and ANSI B16.34 Working Pressure 103.4 Bar / 1500 psi

claudia.madrigal2

Line

Class 600 bellows sealed globe valve, standard bore, outside screw and yoke, non-rising handwheel, union bonnet Available with integral seat or screwed in stainless steel seat or soft seated with O ring in disk Valve can be supplied with pneumatic actuator Butt weld end connections shown, also available as screwed, socket weld, flanged or any special connection.


Materials can be changed to customer specifications. There are temperature restrictions on some materials, ie.

C.st. ASTM A105 is not recommended for use above425 oC.If in doubt please ask, we will advise suitable materialsfor the temperature, pressure and media.

Dimensions Size Dim A Dim B Dim C Weight DN mm mm mm Kg 6 101.6 180 100 3.5 10 101.6 180 100 3.5 15 108 190 100 4 20 117 195 100 4 25 127 200 100 4.5

Component Material Body St.St. Type 316L Bonnet St.St. Type 316L Seat St.St. Type 316L or integral Disk St.St. Type 316L with/without Viton seal Stem St.St. Type 316L Gland Bush St.St. Type 316L Back up Gland PTFE Yoke Bush Aluminium Bronze

Valve Datasheet

27


VALVE TECHNICAL DATASHEETINSTRMENT VALVE - STRAIGHT PATTERN

SERIES 55A




Class 900 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Bolted and lip-seal welded Bonnet. ASME III option available. Secondary Gland in the event of bellows failure. Available with Integral Hard Faced Seat to offer increased resistance against erosion. Valve can be supplied with manual operation or Actuated - Electric or Pneu- matic. Manual Valve and Electrically Actuated Valve shown

Size DN/NPS DN8/3/8” DN15/½” DN20/¾” DN25/1” DN40/1½” DN50/2” DN65/2½” DN80/3” DN100/4”

Manually Operated Electrically Actuated Cv

IGPM/USGPM 7/8.4 7/8.4

12.9/15.4 20.8/25 39/46.8 92/110 125/150 213/255 260/312

Length A mm/in 288/11.34 288/11.34 288/11.34 288/11.34 323/12.72 407/16.03 407/16.03 437/17.2 427/16.82

Height B mm/in 245/9.65 245/9.65 245/9.65 245/9.65 293/11.54 311/12.25 311/12.25 420/16.54 443/17.45

Weight Kg/lb 13.8/30.5 13.8/30.5 13.8/30.5 13.8/30.5 24.1/53.1 46.8/103 46.8/103 97.7/215 183/403

Height D mm/in 551/21.7 551/21.7 551/21.7 551/217 585/23.03 605/23.8 605/23.8 742/29.2 775/30.5

Length E mm/in 245/9.65 245/9.65 245/9.65 245/9.65 293/11.54 311/12.25 311/12.25 420/16.54 443/17.45

Weight Kg/lb

Please Ask For

Details

Valve Shown is with a leak detection port, to provide early warning of any bellows failure. Extended Spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Pneumatically Actuated valves are available.

Materials

Body Bonnet Seat

Disk


316 Stainless Steel St.St. ASME SA182 F316 St.St. ASME SA182 F316 St.St. ASME SA479 F316 or Integral Stellite hard faced St.St. ASME SA479 F316 or St.St. Type 316 hard faced St.St. ASME SA479 F316 St.St. Type 316/316L Exfoliated Graphite Aluminum Bronze

304 Stainless Steel St.St. ASME SA182 F304 St.St. ASME SA182 F304 St.St. ASME SA479 F304 or Integral Stellite hard faced St.St. ASME SA479 F304 or St.St. Type 304 hard faced St.St. ASME SA479 F304 St.St. Type 316/316L Exfoliated Graphite Aluminum Bronze

Valve Datasheet

28


VALVE TECHNICAL DATASHEETLIQUID METAL BELLOW SEALED GLOBE VALVE

LIP-SEAL WELDED BONNET





Class 900 Bellows Sealed Globe Valve, Conventional Bore, Outside Screw and Yoke, Bolted and lip-seal welded Bonnet, with universal joint extended spindle. ASME III option available. Secondary Gland in the event of bellows failure. Available with Integral Hard Faced Seat to offer increased resistance against erosion. Valve can be supplied with manual operation or Actuated - Electric or Pneumatic. Manual Valve shown

Dimensions (typical) Size DN/NPS DN8/3/8” DN15/½” DN20/¾” DN25/1” DN40/1½” DN50/2” DN65/2½” DN80/3” DN100/4”

Length A mm/in 288/11.34 288/11.34 288/11.34 288/11.34 323/12.72 407/16.03 407/16.03 437/17.2 427/16.82

Weight Kg/lb I 13.8/30.5 13.8/30.5 13.8/30.5 13.8/30.5 24.1/53.1 46.8/103 46.8/103 97.7/215 183/403

Cv GPM/USGPM 7/8.4 7/8.4 12.9/15.4 20.8/25 39/46.8 92/110 125/150 213/255 260/312

Materials Valve Shown is with a leakdetection port, to provide early warning of any bellows failure. Extended Spindles, type and length are designed to suit customer requirements. Weights shown are without extended spindle. Extended spindle shown is with intermediate seal/support at the bulge wall level. Design without intermediate stage are available.

Body Bonnet Seat

Disk


316 Stainless Steel St.St. ASME SA182 F316 St.St. ASME SA182 F316 St.St. ASME SA479 F316 or Integral Stellite hard faced St.St. ASME SA479 316 or St.St. Type 316 hard faced St.St. ASTM A182 F316 St.St. Type 316 Exfoliated Graphite Aluminum Bronze

304 Stainless Steel St.St. ASME SA182 F304 St.St. ASME SA182 F304 St.St. ASME SA479 F304 or Integral Stellite hard faced St.St. ASME SA479 F304 or St.St. Type 304 hard faced St.St. ASTM A182 F304 St.St. Type 316 Exfoliated Graphite Aluminum Bronze

Valve Datasheet

29


VALVE TECHNICAL DATASHEETLIQUID METAL BELLOW SEALED GLOBE VALVE LIP-SEAL WELDED BONNET -EXTENDED SPINDLE




Class 2500 Bellows Sealed Globe Valve designed to ASME III, Conventional Bore, Outside Screw and Yoke, Non-rising Handwheel, Bolted Bonnet. Seal Welded Bonnet version available.

Also available with Integral Hard Faced Seat or Screwed in Stainless Steel Seat.

Valve can be supplied with Actuator - Electric or Pneumatic. Buttweld end connections shown, also available as screwed, socket weld, Flanged or special connection Cartridge Valve, seat and all seals are removed with the top assembly. This leaves only body left in line. Maintainence time reduced significantly. Increases safety, no danger of seals being lost down line or seat not being fitted.

Maximum Pressure / Temperature ratings are restricted by the valve end connections and the body / bonnet materials. If in doubt please ask, we will advise suitable materials for the temperature, pressure and media.

Dimensions

Valve Size DN

DN8/¼” DN15/½” DN20/¾” DN25/1” DN40/1½”

Dim A in 10.4” 10.4”

10.75” 12.13” 15.12”

Dim B in 19.69” 19.69” 20.07” 21.38” 23.70”

Weight lb 29.9 29.9

32.66 35.38 40.82 49.9

Cv IGP

M 0.6 1.5 2.4 5

12 21


Body Bonnet Seat Disk

Stem

Bellows Back up Gland

Carbon Steel Valve C.St. ASME SA105 C.St. ASME SA105 St.St. ASME SA479 316L St.St. ASME SA479 316L or ASME SA564 630 St.St. ASME SA479 316L or ASME SA564 630 Hastelloy C276 Exfoliated Graphite

Stainless Steel Valve St.St. ASME SA182 316L St.St. ASME SA182 316L St.St. ASME SA479 316L St.St. ASME SA479 316L or ASME SA564 630 St.St. ASME SA479 316L or ASME SA564 630 Hastelloy C276 Exfoliated Graphite

Valve Datasheet

30


VALVE TECHNICAL DATASHEETBELLOWS SEALED CARTRIDGE VALVE - NUCLEAR

CLASS 200




Index- 1 of 3 Dynamiccontrols.co.uk • T: +44 161 6333933 • [email protected] Cunicocorp.com • T +1 562 7334634 • [email protected]

VALVE TECHNICAL DATA SHEETS Index Page

Valve Datasheet Number

Title Description Application Variants

1 HIGH TEMPERATURE BELLOWS SEALED VALVE SERIES 4

Bellows Sealed Globe Valve Straight Pattern for high temperature applications

Nuclear Power Plants, Marine Applications, Petrochemical Plants, Titanium Production Plant, Magnesium Refining Plant, Rocket Engine Test

Facilities

• Propulsion System• CO2 Cooling Circuits• Primary Heat Transport• Fuel Handling Systems• Radioactive Waste Water

• Decay StoresContainment

• Contaminated StreamContainment

• Nitric Acid Containment• Pond Boron Monitoring

System

• Liquid Sodium/Potassium

‘Alloy’ Circuits Liquid Hydrogen Fuelling

Circuit

Variants - B

2 BELLOWS SEALED CARTRIDGE VALVE-MANIFOLD SERIES 34

Bellows Sealed Cartridge valves in example manifold block

Variants - A

3 BELLOWS SEALED CARTRIDGE VALVE SERIES 34

Bellows Sealed Globe Straight Pattern Cartridge Valve

Variants - A

4 BELLOWS SEALED VALVE SERIES 34

Bellows Sealed Globe Valve Straight Pattern Seal welded Bonnet

Variants - B

5 BELLOWS SEALED VALVE SERIES 34

Bellows Sealed Globe Valve Straight Pattern Bolted Bonnet

Variants - B

6 BELLOWS SEALED VALVE NUCLEAR -SERIES 34

Bellows Sealed Globe Valve Straight Pattern Bolted Bonnet to ASME III

Variants - B

7 BELLOWS SEALED CARTRIDGE VALVE EXTREME -SERIES 34

Bellows Sealed Globe Straight Pattern Cartridge Valve. For extreme duties

Variants - A

8 HIGH TEMPERATURE BELLOWS SEALED VALVE SERIES 34

Bellows Sealed Globe Valve Straight Pattern for high temperature applications

Variants - B

9 BOLTED BONNET VALVE – STRAIGHT PATTERNSERIES 34A

Bellows Sealed Globe Valve Straight Pattern Bolted Bonnet

Variants - B

10 BOLTED BONNET VALVE -OBLIQUE PATTERNSERIES 34B

Bellows Sealed Globe Valve Y Pattern Bolted Bonnet

Variants - B

11 BOLTED BONNET VALVE -ANGLE PATTERNSERIES 34C

Bellows Sealed Globe Valve Angle Pattern Bolted Bonnet

Variants - B

12 SEAL WELDED BONNET VALVE – STRAIGHT PATTERN -SERIES 35A

Bellows Sealed Globe Valve Straight Pattern Seal welded Bonnet

Variants - B

13 SEAL WELDED BONNET VALVE-OBLIQUE PATTERN -SERIES 35B

Bellows Sealed Globe Valve Y Pattern Seal welded Bonnet

Variants - B


14 SEAL WELDED BONNET VALVE -ANGLE PATTERN SERIES 35C

Bellows Sealed Globe Valve Angle Pattern Seal welded Bonnet

Variants - B

15

BOLTED/EDGE WELDED BONNET VALVE -STRAIGHT PATTERN SERIES 36A

Bellows Sealed Globe Valve Straight Pattern Bolted / Edge welded Bonnet

Variants - B

16

BOLTED/EDGE WELDED BONNET VALVE -OBLIQUE PATTERN SERIES 36B

Bellows Sealed Globe Valve Y Pattern Bolted / Edge welded Bonnet

Nuclear Power Plants, Marine Applications, Petrochemical Plants,

Titanium Production Plant, Magnesium Refining Plant,

Rocket Engine Test Facilities

• Propulsion System

• CO2 Cooling Circuits• Primary Heat Transport• Fuel Handling Systems• Radioactive WasteWater

• Decay Stores Containment

• Contaminated StreamContainment

• Nitric Acid Containment• Pond Boron Monitoring

System

• Liquid Sodium/Potassium‘Alloy’ Circuits

• Liquid Hydrogen FuellingCircuit

Variants - B

17 BOLTED/EDGE WELDED BONNET VALVE -ANGLE PATTERN -SERIES 36C

Bellows Sealed Globe Valve Angle Pattern Bolted / Edge welded Bonnet

Variants - B

18 BELLOWS SEALED STOP AND STOP/CHECK VALVE SERIES 40A

Bellows Sealed Globe Straight Pattern Cartridge Valve. Stop valve and Stop check options

Variants - A

19 BELLOWS SEALED STOP AND STOP/CHECK VALVE SERIES 40B

Bellows Sealed Globe Y Pattern Cartridge Valve. Stop valve and Stop check options

Variants - A

20

BOLTED BONNET CARTRIDGE VALVE -ANGLE PATTERN SERIES 40C

Bellows Sealed Globe Angle Pattern Cartridge Valve.

Variants - A

21 STOP AND STOP/CHECK VALVE SERIES 50A

Globe Straight Pattern Cartridge Valve. Stop valve and Stop check options

Variants - A

22 STOP AND STOP/CHECK VALVE SERIES 50B

Globe Y Pattern Cartridge Valve. Stop valve and Stop check options

Variants - A

23 NON-BELLOWS SEALED VALVE -ANGLE PATTERN GLOBE -SERIES 50C

Globe Angle Pattern Cartridge Valve. Stop valve

Variants - A

24

NON-BELLOWS SEALED VALVE -STRAIGHT PATTERN NON-RETURN SERIES 50D

Globe Straight Pattern Piston Check Valve

Variants - C

25 CHECK VALVE SERIES 50D1

Globe Straight Pattern Piston Check Cartridge Valve. Stop valve and Stop check options

Variants - D

Valve Datasheet

Number Title Description Application Variants


26 CHECK VALVE SERIES 50D2

Globe Y Pattern Piston Check Cartridge Valve. Stop valve and Stop check options

Nuclear Power Plants, Marine Applications, Petrochemical Plants, Titanium Production Plant, Magnesium Refining Plant, Rocket Engine Test Facilities • Propulsion System• CO2 Cooling Circuits• Primary Heat Transport• Fuel Handling Systems• Radioactive Waste

Water• Decay Stores

Containment• Contaminated Stream

Containment • Nitric Acid Containment• Pond Boron Monitoring

System• Liquid

Sodium/Potassium‘Alloy’ Circuits

Liquid Hydrogen Fuelling Circuit

Variants - D

27 INSTRUMENT VALVE -STRAIGHT PATTERN SERIES 55A

Instrument Valve straight pattern union bonnet

Variants - B

28

LIQUID METAL BELLOW SEALED GLOBE VALVE -LIP-SEAL WELDED BONNET

Bellows Sealed Globe Valve Y Pattern Bolted / Edge welded Bonnet for liquid metal applications

Variants - B

29

LIQUID METAL BELLOW SEALED GLOBE VALVE -LIP-SEAL WELDED BONNET -EXTENDED SPINDLE

Bellows Sealed Globe Valve Y Pattern Bolted / Edge welded Bonnet with extended spindle for liquid metal applications

Variants - B

30 CLASS 2500 BELLOWS SEALED CARTRIDGE VALVE -NUCLEAR

Bellows Sealed Cartridge Valve Straight Pattern Bolted Bonnet for high pressure applications

Variants - A

Bespoke versions to Customer Specifications can be Developed - Talk to Manufacturer

Submarines • Dreadnought Class • Trafalgar Class • Vanguard Class

Power Stations • Hinkley PS • Heysham PS • Torness PS • Dounreay PS• Wylfa PS • Hunterstone PS • Dungeness PS

Applications

Variants - A: Nuclear to ASME III Class I, II or III. Non-cartridge Seal Welded Bonnet for Liquid Metal Applications. Non-Cartridge Cryogenic version with/without vacuum jacket. Soft seat, metal seat, hard faced seat and integral seat options. Electric, Pneumatic or Hydraulic actuation. Bespoke End Connections. Extended Spindle to remove handwheel (or actuator) from Hot/Cold or active area.

Variants - C: Nuclear to ASME III Class I, II or III. Cartridge Version. Soft seat, metal seat, hard faced seat and integral seat options. Bespoke End Connections. Tight shut-off at low pressure version available.

Variants - B: Nuclear to ASME III Class I, II or III. Cartridge Version Cartridge Cryogenic version with/without vacuum jacket. Soft seat, metal seat, hard faced seat and integral seat options. Electric, Pneumatic or Hydraulic actuation. Bespoke End Connections. Extended Spindle to remove handwheel (or actuator) from Hot/Cold or active area.

Variants - D: Nuclear to ASME III Class I, II or III. Non-cartridge Seal Welded Bonnet for Liquid Metal Applications. Soft seat, metal seat, hard faced seat and integral seat options. Bespoke End Connections.

Tight shut-off at low pressure version available.

Valve Datasheet

Number

Title Description Application Variants

valve technical data sheet high temperature bellows … · 2020. 9. 29. · bellows sealed valve -...

Documents