type 227a1 ii 2 g d - phone-master · 2014. 5. 23. · l'installation du matériel doit être...
TRANSCRIPT
NFC227A*TEL21 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
GUIDE D’INSTRUCTION TELEPHONES ANTIDEFLAGRANTSATEX - GAZ ET POUSSIERE
USER GUIDE EXPLOSION-PROOF TELEPHONESATEX – GASES AND DUST
TYPE 227A1 II 2 G D
Groupe LE LASCOMMUNICATION SOUS HAUTE PROTECTIONCOMMUNICATING IN SAFETY
NFC227A*TEL22 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
SOMMAIRE
1. PRESENTATION................................................................................................................... 41.1 CARACTERISTIQUES GENERALES................................................................................... 41.2 CONTENU DE L’EMBALLAGE ........................................................................................... 51.3 PRESENTATION GENERALE DES POSTES TYPE 227A1.................................................. 51.4 GUIDE D'INSTRUCTION/MISE EN SERVICE/DE MAINTENANCE.................................. 61.5 CARACTERISTIQUES TECHNIQUES DES POSTES TYPE 227A1..................................... 71.6 CONDITIONS PARTICULIERES.......................................................................................... 81.7 DESCRIPTIF DES POSTES TYPE TLA 227A1A................................................................... 91.8 DESCRIPTIF DES POSTES TYPE TLC 227A1A................................................................. 101.9 DESCRIPTIF DES POSTES TYPE TLA 227A1AT .............................................................. 111.10 DESCRIPTIF DES POSTES TYPE TLC 227A1AT............................................................. 121.11 DESCRIPTIF DU CLAVIER DE NUMEROTATION......................................................... 13
2. INSTALLATION DES POSTES TYPE 227A1 .................................................................. 14
3. PRESENTATION DE LA CARTE TELEPHONIQUE (REF.: WK221 CMAATX)........ 15
4. RACCORDEMENT DES POSTES TELEPHONIQUES TYPE 227A1............................ 164.1 OUVERTURE DU POSTE TELEPHONIQUE ..................................................................... 164.2 RACCORDEMENT DE LA LIGNE TELEPHONIQUE........................................................ 164.3 MISE A LA TERRE DU POSTE TELEPHONIQUE ............................................................. 16
5. UTILISATION DES POSTES TELEPHONIQUES A CLAVIER TLA 227 A1A............ 17
6. UTILISATION DES POSTES TELEPHONIQUES BC TLC 227 A1A ............................ 17
7. UTILISATION DES POSTES TELEPHONIQUES A CLAVIER TLA 227 A1AT ......... 19
8. UTILISATION DES POSTES TELEPHONIQUES BC TLC 227 A1AT ......................... 21
9. PROGRAMMATION DE BASE ......................................................................................... 23
10. UTILISATION ET PROGRAMMATION DU POSTE TLS227A1C4............................ 25
11. ENTRETIEN ...................................................................................................................... 27
12. EN CAS DE PROBLEME.................................................................................................. 27
13. PROGRAMMATION EVOLUEE..................................................................................... 28
NFC227A*TEL23 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
CONTENTS
1. PRESENTATION................................................................................................................. 331.1 GENERAL FEATURES ....................................................................................................... 331.2 CONTENTS OF PACKAGE................................................................................................. 341.3 GENERAL PRESENTATION OF SERIES 227 TELEPHONES. .......................................... 341.4 USER INSTRUCTION / SET-UP / MAINTENANCE........................................................... 351.5 TECHNICAL FEATURES OF SERIES 227A1 TELEPHONES ............................................ 361.6 SPECIAL CONDITIONS OF USE ........................................................................................ 361.7 DESCRIPTION OF TYPE TLA 227A1A TELEPHONES ..................................................... 371.8 DESCRIPTION OF TYPE TLC 227A1A TELEPHONES ..................................................... 381.9 DESCRIPTION OF TYPE TLA 227A1AT TELEPHONES................................................... 391.10 DESCRIPTION OF TYPE TLC 227A1AT TELEPHONES................................................. 401.11 DESCRIPTION OF KEYPAD ............................................................................................ 41
2. INSTALLATION OF 227A1 TELEPHONES .................................................................... 42
3. TELEPHONE CARD LAYOUT (REF.: WK221 CMAATX)............................................ 43
4. CONNECTION OF 227A1 TELEPHONES ....................................................................... 444.1 OPENING THE TELEPHONE ............................................................................................. 444.2 CONNECTION OF THE TELEPHONE LINE...................................................................... 444.3 EARTHING THE TELEPHONE .......................................................................................... 44
5. USAGE OF TELEPHONES WITH KEYPAD TLA 227 A1A........................................... 45
6. USAGE OF CB TELEPHONES TLC 227 A1A.................................................................. 46
7. USAGE OF TELEPHONES WITH KEYPAD TLA 227 A1AT ........................................ 47
8. USAGE OF CB TELEPHONES TLC 227 A1AT ............................................................... 49
9. BASIC PROGRAMMING ................................................................................................... 51
10. TLS 227 A1C4 USER MANUAL WITH MEMORY FACILITY.................................... 54
11. MAINTENANCE................................................................................................................ 55
12. IN THE EVENT OF A PROBLEM................................................................................... 55
13. ADDITIONAL PROGRAMMING.................................................................................... 56
NFC227A*TEL24 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
POSTES TELEPHONIQUES ANTIDEFLAGRANTS TYPE 227A1 ET VARIANTES
1 PRESENTATION
1.1 CARACTERISTIQUES GENERALESMATERIEL POUR SITES INDUSTRIELS TELEPHONES ANTIDEFLAGRANTS
TYPE 227A1MARQUAGELe marquage comporte les indications suivantes :
• Adresse : LE LAS34/36 RUE ROGER SALENGROF94134 FONTENAY SOUS BOIS - FRANCE
• Le marquage : CE0080• La désignation du type : 227A1• L’année de construction : 200-
• Le marquage spécifique : II 2 G D• Le marquage complémentaire : em [ib] ib II CT5• Certificat de conformité : INERIS 03ATEX0118X• La température ambiante d’utilisation : Tamb. = -40°C à +60°C• Tensions et courants nominaux : voir conditions particulières page 8
CE PRODUIT REPOND A L’INDICE DE PROTECTION D’ETANCHEITE IP65
CHAQUE COMPOSANT FAIT PARTIE INTEGRANTE DU MODEDE PROTECTION ET NE PEUT EN AUCUN CAS ETRE MODIFIE,
Y COMPRIS LES ENTREES DE CABLES.
LA GARANTIE NE S’APPLIQUE QUE DANS LES CONDITIONS D’INSTALLATIONET DE FONCTIONNEMENT STRICTEMENT DEFINIES DANS CE MANUEL.
AUCUNE GARANTIE NE PEUT ETRE MISE EN OEUVRESI LA DETERIORATION RESULTE D’UNE CAUSE ETRANGERE
A L’APPAREIL OU DU NON RESPECT DES PRESCRIPTIONS D’UTILISATION.
DANS UN SOUCI D’AMELIORATION, LES INFORMATIONS CONTENUES DANSCE DOCUMENT ET LES CARACTERISTIQUES DES MATERIELS PEUVENT
FAIRE L’OBJET DE MODIFICATIONS SANS PREAVIS.
NORMES EUROPEENNES
LES UNITES PORTANT LA MENTION « CE » SONT CONFORMES A LA DIRECTIVE EMC (89/336/CEE),A LA DIRECTIVE RELATIVE AUXBASSES TENSIONS (73/23/CEE)
FORMULEES PAR LA COMMUNAUTE EUROPEENNE.
LES UNITES PORTANT LA MENTION « Ex » SONT CONFORMES A LA DIRECTIVE ATEX 94/9/CEET CONFORME AUX NORMES EUROPEENNES
EN 50 014 - 1997, EN 50 019 - 1994, EN 50 020 - 2002, EN 50 028 – 1987, EN 50 281 – 1998
Les normes de la série EN 50 XXX ne sont plus celles qui sont harmonisées, mais que la conformité dumatériel n’est pas impacté par les modifications substantielles des normes de la série EN 60079 et EN 61241.
AGREMENT ART N° 98667P DU 29 JUILLET 1998
REMARQUE
NFC227A*TEL25 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.2 CONTENU DE L’EMBALLAGEL’équipement que vous venez d’acquérir comprend :
• Un poste téléphonique• Une notice d’instruction• La visserie pour fixation murale Réf : GM208A12
1.3 PRESENTATION GENERALE DES POSTES TYPE 227A1.Le poste téléphonique est de type mural antidéflagrant, BC ou BCA et se compose essentiellement:
• d'un carter protégé par sécurité augmentée, contenant deux cartes à circuits imprimés protégéespar sécurité intrinsèque, et un ensemble de composants électroniques noyé dans une résine etprotégé par enrobage. La carte à circuit imprimé enrobée comporte, sur sa face supérieure, deuxbornes "e" pour le raccordement de la ligne téléphonique.
• d'un combiné téléphonique en alliage léger protégé par sécurité intrinsèque (IP65).
• d'un second récepteur, en option, également protégé par sécurité intrinsèque.
La fermeture du couvercle s’effectue sur joint d’étanchéité par 3 vis (M6) six pans creux ouspéciales (inviolable en option) nécessitant une clé adéquate pour l’ouverture.
FONCTIONNALITES
Pour tous les types de postes:
• Numérotation multifréquences (DTMF) et décimale (pour les postes type BCA).• Modification des réglages à distance par un poste classique DTMF ou par station de maintenance
(option) par exemple:Ø Type de sonnerieØ Volume de sonnerieØ Volume haut parleurØ Type de numérotation
Pour les postes mains libres:
• Possibilité de raccroché automatique.• Possibilité de décrochage instantané ou après un nombre programmable de sonneries.• Possibilité d’« Antipiaf » (micro utilisable après numérotation interne).• Programmation des numéros mémorisés en local ou à distance par téléphone type DTMF.• Possibilité d’enchaînement de plusieurs numéros en cas d’occupation ou de non réponse après un
temps programmable.• Décroché automatique
NFC227A*TEL26 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.4 GUIDE D’INSTRUCTIONS POSTE TELEPHONIQUE TYPE 227A1
LA PREMIERE MISE EN SERVICE DOIT ETRE EFFECTUEE PAR UNE SOCIETECOMPETENTE EN INSTALLATION EN ZONE A RISQUE.
IMPORTANT
AUCUNE INTERVENTION OU MODIFICATION DE L’APPAREILPAR VOS SOINS N’EST AUTORISEE SANS L’ACCORD DU FABRICANT.
MISE EN SERVICE / UTILISATION
Les instructions qui suivent doivent être lues conjointement avec :
1- la norme NF C 15 1002- la norme EN 60 079-14 (installations électriques en atmosphères explosives gazeuses)3- la norme EN 60 079-17 (inspection et entretien dans les emplacements dangereux)4- la norme EN 50 281-1-2 (matériels électriques destinés à être utilisés en présence de poussières
combustibles. Partie 1-2 : matériels électriques protégés par enveloppes - Sélection, installationet entretien)
5- les décrets, les arrêtés, les lois, les directives, les circulaires d'applications, les normes, les règlesde l'art et tout autre document concernant son lieu d'installation.
Les non-respects de celles-ci ne sauraient engager notre responsabilité.L'installation du matériel doit être réalisée par du personnel qualifié, compétent et habilité.
S'assurer de la compatibilité entre les indications figurant sur la plaque signalétique, l'atmosphèreexplosive présente, la zone d'utilisation et les températures ambiantes et de surface.
INSTRUCTIONS DE MAINTENANCE
La vérification des points suivants doit être effectuée au moins une fois par an.
Ø L'équipement extérieur et les faces ne doivent pas être endommagés.
Ø Vérifier le serrage des bornes et autres connexions; re-câbler si nécessaire.
Ø Avant fermeture, vérifier le joint d’étanchéité du boîtier, la propreté, son état ainsi que sa mise en place.
Ø Fixer le couvercle sur le boîtier et s'assurer que les 3 vis de fermeture sont bien serrées.
Ø Vérifier le serrage du presse étoupe sur le ou les câbles afin d’assurer l’étanchéité.(Attention : les presses étoupe montés sur les appareils Groupe IIC sont spécifiques aux Groupe de
gaz utilisés).
Conditions particulières voir page 8
NFC227A*TEL27 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.5 CARACTERISTIQUES TECHNIQUES DES POSTES TYPE 227A1
CES PRODUITS, EQUIPES D’UN MICROPROCESSEUR, EFFECTUENT, LORS DURACCORDEMENT A LA LIGNE TELEPHONIQUE, UN AUTO-TEST PONCTUE
PAR L’EMISSION D’UN SIGNAL SONORE.
ILS POSSEDENT DE NOMBREUSES FONCTIONS PROGRAMMABLESET SONT CONFIGURES EN USINE POUR UN USAGE COURANT.
AVANT DE PROCEDER A LA MISE EN SERVICE, LIRE ATTENTIVEMENT LEMANUEL FOURNI POUR S’ASSURER QUE LA CONFIGURATION
USINE CORRESPOND A L’UTILISATION SOUHAITEE.
Les postes « ADF » fonctionnent sans aucune modification sur les réseaux publics type FranceTélécom. Pour un fonctionnement correct sur un autocommutateur privé, il faut s’assurer que lescaractéristiques suivantes coïncident avec celles de votre autocommutateur.Dans le cas contraire procéder aux corrections en utilisant les moyens de programmation.
En cas d’incompatibilité, des logiciels sur demande peuvent être exécutés, contactez le constructeurpour plus d’informations.
Pour tous les types de postes:
• Tension d’appel reçue de l’autocommutateur > 35 Veff < U sonnerie < 80Veff CA 25 ou 50HzDurée sonnerie: 1.5s ± 0.5s Imax = 0,05 Aeff ; Pmax = 1 WDurée pause: 3s ± 2 sPuissance sonnerie pour Umax = 80Veff : env. 85dB
• Courant dans le poste (position décroché) 35mA (20mA minimum)Imax = 0,08 ADC ; Pmax = 1,2 W
• Tension aux bornes du poste (position raccroché) 48V (24V minimum) Umax = 60 VDC
• Système de numérotation DTMF ou Décimale
ATTENTION
NFC227A*TEL28 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
Pour les postes mains libres:
• Tonalité d’invitation à numéroter Tonalité continueFréquence: de 270 à 540Hz temps de détection min 2 sec.
• Tonalité d’occupationFréquence: 300 à 500 HzSéquence de bip et pause de plus de 10 secondes. temps de détection 4-10 secBip: 100 à 600 msPause: 100 à 600 ms ( = au bip)
• Retour Tonalité d’appel distantFréquence: 350 à 500HzSéquence de bip et pause jusqu’au décroché distantBip: 0.2sec. à 1.6 sec.Cycle bip + pause inférieur à 6 secondes.
• Tonalité cadencée de libération de la conversationFréquence: 300 à 500 HzSéquence de bip et pause de plus de 10 secondes. temps de détection 4-10 secBip: 100 à 600 msPause: 100 à 600 ms ( = au bip)
• Tonalité continue de libération de la conversationFréquence: 300 à 500 Hz ou 760 à 840 HzDurée du bip supérieure à 10 secondes. temps de détection 6-10 sec
1.6 CONDITIONS PARTICULIERESLe téléphone type 227A1 doit être raccordé sur une ligne téléphonique ayant les caractéristiquessuivantes :
Ø Tension nominale d’alimentation : Umax. = 60Vcc
Ø Courant fourni : Imax. = 80mA
Ø Puissance dissipée : Pmax. = 1.2W
NFC227A*TEL29 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.7 DESCRIPTIF DES POSTES TYPE TLA 227A1A
La version TLA 227A1A comporte un clavier 14 touches et fonctionne uniquement en modecombiné.
A - Carte téléphone DC/MF réf: WK221CMAATXB - Carte de protection intrinsèque réf: WK118PLIATXC - Carte clavier réf: WK092CMAD - 2 entrées de cable Eex pour cable ∅10 à 13 mm réf : EEL13C10*13ATXE - Combiné en métal léger réf: MS436A13F - Pattes de fixation en option réf: GM337E2G - Second récepteur en option réf: MS533A2AH - Hurleur piézo
NFC227A*TEL210 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.8 DESCRIPTIF DES POSTES TYPE TLC 227A1A
Cette version est de type BC (batterie centrale) sans clavier.
A - Carte téléphone DC/MF réf: WK221CMAATXB - Carte de protection intrinsèque réf: WK118PLIATXC - 2 entrées de cable Eex pour cable ∅10 à 13 mm réf : EEL13C10*13ATXE - Combiné en métal léger réf: MS436A13F - Pattes de fixation en option réf: GM337E2G - Second récepteur en option réf: MS533A2AH - Hurleur piézo
NFC227A*TEL211 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.9 DESCRIPTIF DES POSTES TYPE TLA 227A1AT
La version TLA 227 A1AT comporte un clavier 15 touches plus 1 voyant prise de ligne et peutfonctionner en mode combiné ou mains libres. Cette version peut être associée à une station detélémaintenance.
A - Carte téléphone DC/MF réf: WK221CMATATXB - Carte de protection intrinsèque réf: WK118PLIATXC - Carte clavier réf: WK092CMAD - 2 entrées de cable Eex pour cable ∅10 à 13 mm réf : EEL13C10*13ATXE - Microphone type électret réf: CE515V2F - Combiné en métal léger réf: MS436A13G - Pattes de fixation en option réf: GM337E2H - Second récepteur en option réf: MS533A2AI - Haut parleur
NFC227A*TEL212 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.10 DESCRIPTIF DES POSTES TYPE TLC 227A1AT
La version TLC 227 A1AT est un poste type BC, il comporte un clavier 1 touche avec voyant deprise de ligne et peut fonctionner en mode combiné ou mains libres. Cette version peut être associéeà une station de télémaintenance.
A - Carte téléphone DC/MF réf: WK221CMATATXB - Carte de protection intrinsèque réf: WK118PLIATXC - Carte clavier réf: WK092CMAD - 2 entrées de cable Eex pour cable ∅10 à 13 mm réf : EEL13C10*13ATXE - Microphone type électret réf: CE515V2F - Combiné en métal léger réf: MS436A13G - Pattes de fixation en option réf: GM337E2H - Second récepteur en option réf: MS533A2AI - Haut parleur
NFC227A*TEL213 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.11 DESCRIPTIF DU CLAVIER DE NUMEROTATION
Clavier étanche à 15 touches avec témoin lumineux de prise de ligne. Equipement selon modèle.Une membrane autocollante située entre les poussoirs et les micro contacts assure l’étanchéité du clavier.La sérigraphie est fonction du modèle.
NOTA : il est possible d’attribuer un numéro préprogrammé à chaque touche du clavier (0 à 9) par touchemémoire uniquement en mode mains libres, voir chapitre « Programmation des numéros d’appel »page 22.
• Poste télésurveillé : 8 touches mémoires M1 à M8 utilisables par appui sur une des touches 1 à 8 sansprendre la ligne.
• Poste non télésurveillé : 10 touches mémoires M0 à M9 utilisables par appui sur une des touches 0 à 9sans prendre la ligne.
LA TOUCHE A UNE DOUBLE FONCTIONNALITE
SELON LA PROGRAMMATION:FLASHING OU MEMOIRE DIRECTE M1
Chaque fonction est décrite séparément dans les § 5,6,7,8.
REMARQUE
NFC227A*TEL214 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
2 INSTALLATION DES POSTES TYPE 227A1
PLAN DE PERCAGE
NOTA : La fixation murale doit se faire obligatoirement à l’aide de vis en acier inoxydable.
NFC227A*TEL215 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
MIN MAX
MIN MAX
3 PRESENTATION DE LA CARTE TELEPHONIQUE (REF.: WK221 CMAATX)
FONCTIONS ET REGLAGES DES CAVALIERS
PG 140B16
FONCTIONS REPERES CAVALIERSSENSIBILITE DU MICROPHONE MAINS LIBRES• Sensibilité à 1 mètre : placer le cavalier sur MAX• Sensibilité à 30 cm : placer le cavalier sur MIN
ST1
REGLAGE DU SEUIL DE BRUIT• Réglage MIN : pour local silencieux• Réglage MAX : pour local très bruyantNOTA : un réglage normal est effectué en usine (selon dessin)
R28 MINMAX
NFC227A*TEL216 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
4 RACCORDEMENT DES POSTES TELEPHONIQUES TYPE 227A1
4.1 OUVERTURE DU POSTE TELEPHONIQUE
Pour avoir accès aux circuits du poste, dévisser les 3 points de fixations du couvercle à l’aide d’uneclé ALLEN #5.
4.2 RACCORDEMENT DE LA LIGNE TELEPHONIQUE
Le raccordement du poste à la ligne téléphonique s’effectue sur la carte de protection intrinsèqueWK118PLIATX par connecteur enfichable et vérrouillable, (en sécurité augmenté).
Raccorder la ligne téléphonique aux bornes L1 et L2, qui sont doublées pour faciliter les extensions.Les bornes de raccordement admettent des fils mono brin ou multibrins d’une section maxi de1.5mm².
4.3 MISE A LA TERRE DU POSTE TELEPHONIQUE
La mise à la terre électrique s’effectue de façon :• par la vis de terre équipée d’une cosse de section de 4 à 6mm² (située sur la face inférieure du carter) repérée par le sigle ⊥.• Par la vis de terre équipée d’une cosse de section de 1.5mm² (située sur la face l’intérieur du carter) repérée par le sigle ⊥.
NFC227A*TEL217 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
5 UTILISATION DES POSTES TELEPHONIQUES A CLAVIER TLA 227 A1A
Les appareils type 227A1 sont des postes téléphoniques, leur fonctionnement est sous la responsabilité de sonutilisateur.
COMMENT APPELER
Lorsque la communication est terminée, pour rendre la ligne:
COMMENT REPONDRE A UN APPEL
Lorsque la sonnerie retentit
Lorsque la communication est terminée, pour rendre la ligne:
RAPPEL DU DERNIER NUMERO COMPOSE
Lorsque la communication est terminée, pour rendre la ligne:
DECROCHER LE COMBINE
COMPOSER LE NUMERO
RACCROCHER LE COMBINE
DECROCHER LE COMBINE
RACCROCHER LE COMBINE
DECROCHER LE COMBINE
1
APPUYER SUR BIS
2
3
1
2
1
2
RACCROCHER LE COMBINE3
I
NFC227A*TEL218 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
EMISSION D’UNE OUVERTURE DE LIGNE (FLASHING)
Une ouverture de ligne programmée à 270 ms est provoquéeLa durée du flashing peut être modifiée par programmation
La touche R à une double fonctionnalité selon la programmation: Flashing ou mémoire directe M1 (voirchapitre programmation page 22).
LA DUREE D’UNE CONVERSATION PEUT ETRE LIMITEE PAR PROGRAMMATION
6 UTILISATION DES POSTES TELEPHONIQUES BC TLC 227 A1A
Les appareils type 227A1 sont des postes téléphoniques, leur fonctionnement est sous la responsabilité de sonutilisateur.
COMMENT APPELER
Lorsque la communication est terminée, pour rendre la ligne:
COMMENT REPONDRE A UN APPEL
Lorsque la sonnerie retentit
Lorsque la communication est terminée, pour rendre la ligne:
APPUYER SUR LA TOUCHE
NOTA
DECROCHER LE COMBINE
RACCROCHER LE COMBINE
DECROCHER LE COMBINE
RACCROCHER LE COMBINE
1
2
1
2
NFC227A*TEL219 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
7 UTILISATION DES POSTES TELEPHONIQUES A CLAVIER TLA 227 A1AT
Les appareils type 227A1 sont des postes téléphoniques, leur fonctionnement est sous la responsabilité de sonutilisateur.
• Fonctionnement d’un poste avec passage du combiné en mains libres avec clavier:- Décroché du combiné ⇒ prise de ligne/combiné- Appui sur la touche PL ⇒ mains libres- Appui sur la touche PL ⇒ combiné- Raccroché du combiné ⇒ pause de ligneou:- Décroché du combiné ⇒ prise de ligne/combiné- Appui sur la touche PL ⇒ mains libres- Raccroché du combiné ⇒ mains libres- Appui sur la touche PL ⇒ pause de ligneou:- Appui sur la touche PL ⇒ prise de ligne/mains libres- Décroché du combiné ⇒ combiné- Raccroché du combiné ⇒ mains libres- Appui sur la touche PL ⇒ pause de ligne
Si le combiné n’est pas remis en place (vandalisme, combiné arraché) le poste reste fonctionnel enmains libres.
COMMENT APPELER
Le témoin rouge s’allume
Au décroché du correspondant, converser en face du poste à unedistance approximative de 20 cm ou dans le combiné
Lorsque la communication est terminée, pour rendre la ligne:
Le témoin rouge s’éteint.
NOTA : il est possible d’attribuer un numéro préprogrammé à chaque touche du clavier (0 à 9) par touchemémoire uniquement en mode mains libres, voir chapitre « Programmation des numéros d’appel »page 22.
APPUYER SUR LE BOUTON PRISE DE LIGNEOU DECROCHER LE COMBINE
COMPOSER LE NUMERO
APPUYER SUR LE BOUTON DE PRISE DE LIGNEOU RACCROCHER LE COMBINE
OU LAISSER LE POSTE RACCROCHERAUTOMATIQUEMENT
1
2
3
NFC227A*TEL220 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
COMMENT REPONDRE A UN APPEL
Lorsque la sonnerie retentit
Le témoin rouge s’allume en fixe
Au décroché du correspondant converser en face du poste à unedistance approximative de 20 cm ou dans le combiné.
Lorsque la communication est terminée, pour rendre la ligne:
Le témoin rouge s’éteint.
RAPPEL DU DERNIER NUMERO COMPOSE
Le témoin rouge s’allume
Au décroché du correspondant, converser en face du poste à unedistance approximative de 20 cm ou dans le combiné
Lorsque la communication est terminée, pour rendre la ligne:
Le témoin rouge s’éteint.
APPUYER SUR LE BOUTON PRISE DE LIGNEOU DECROCHER LE COMBINE
APPUYER SUR LE BOUTON DE PRISE DE LIGNEOU RACCROCHER LE COMBINE
OU LAISSER LE POSTE RACCROCHERAUTOMATIQUEMENT
APPUYER SUR BIS
1
2
2I
APPUYER SUR LE BOUTON PRISE DE LIGNEOU DECROCHER LE COMBINE
1
APPUYER SUR LE BOUTON DE PRISE DE LIGNEOU RACCROCHER LE COMBINE
OU LAISSER LE POSTE RACCROCHERAUTOMATIQUEMENT
3
NFC227A*TEL221 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
EMISSION D’UNE OUVERTURE DE LIGNE (FLASHING)
Une ouverture de ligne programmée à 270 ms est provoquéeLa durée du flashing peut être modifiée par programmation
La touche R à une double fonctionnalité selon la programmation: Flashing ou mémoire M1(voir chapitre programmation de base page 22).
LA DUREE D’UNE CONVERSATION PEUT ETRE LIMITEE PAR PROGRAMMATION
8 UTILISATION DES POSTES TELEPHONIQUES BC TLC 227 A1AT
Les appareils type 227A1 sont des postes téléphoniques, leur fonctionnement est sous la responsabilité de sonutilisateur.
• Fonctionnement d’un poste avec passage du combiné en mains libres BC:- Décroché du combiné ⇒ prise de ligne/combiné- Appui sur la touche PL ⇒ mains libres- Appui sur la touche PL ⇒ combiné- Raccroché du combiné ⇒ pause de ligneou:- Décroché du combiné ⇒ prise de ligne/combiné- Appui sur la touche PL ⇒ mains libres- Raccroché du combiné ⇒ mains libres- Appui sur la touche PL ⇒ pause de ligneou:- Appui sur la touche PL ⇒ prise de ligne/mains libres- Décroché du combiné ⇒ combiné- Raccroché du combiné ⇒ mains libres- Appui sur la touche PL ⇒ pause de ligne
Si le combiné n’est pas remis en place (vandalisme, combiné arraché) le poste reste fonctionnel enmains libres.
APPUYER SUR LA TOUCHE
NOTA
NFC227A*TEL222 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
COMMENT APPELER
Le témoin rouge s’allume
Au décroché du correspondant, converser en face du poste à unedistance approximative de 20 cm ou dans le combiné
Lorsque la communication est terminée, pour rendre la ligne:
Le témoin rouge s’éteint.
COMMENT REPONDRE A UN APPEL
Lorsque la sonnerie retentit
Le témoin rouge s’allume en fixe
Au décroché du correspondant converser en face du poste à unedistance approximative de 20 cm ou dans le combiné.
Lorsque la communication est terminée, pour rendre la ligne:
Le témoin rouge s’éteint.
APPUYER SUR LE BOUTON PRISE DE LIGNEOU DECROCHER LE COMBINE
APPUYER SUR LE BOUTON DE PRISE DE LIGNEOU RACCROCHER LE COMBINE
OU LAISSER LE POSTE RACCROCHERAUTOMATIQUEMENT
APPUYER SUR LE BOUTON PRISE DE LIGNEOU DECROCHER LE COMBINE
APPUYER SUR LE BOUTON DE PRISE DE LIGNEOU RACCROCHER LE COMBINE
OU LAISSER LE POSTE RACCROCHERAUTOMATIQUEMENT
1
2
1
2
NFC227A*TEL223 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
9 PROGRAMMATION DE BASESéquence de touches à faire sur le clavier d’un poste téléphonique distant, type DTMF, en liaisonavec le poste à programmer.Attention pendant une programmation, la présence d’une tonalité d’occupation peut raccrocher leposte automatiquement.IMPORTANT : Avant toute programmation, taper le code d’accès
* 1 2 3 4 *
PROGRAMMATION D’UN NUMERO D’APPEL UNIQUE (M1)
Taper la combinaison suivante:
* 5 0 0 1 * # 1 1 # <N> *< N > numéro d’appel de 1 à 15 chiffres.
Dans la programmation d’une mémoire, la combinaison #11# représente une recherche de tonalité continue defréquence 440 Hz ± 100 Hz (standard ) avant de numéroter. Si votre autocommutateur ne correspond pas austandard vous pouvez remplacer la recherche de tonalité par une pause 2 secondes, dans ce cas, remplacer[#11#] par [#10#] dans la séquence.
PROGRAMMATION DES NUMEROS D’APPEL (M0 A M9)
Taper la combinaison suivante pour chaque bouton:
* 5 0 0 <M> * # 1 1 # <N> *< M > numéro de mémoire de 0 à 9 affecté aux boutons 0 à 9.
à l’exception des postes à 2 boutons où le bouton 2 est affecté à M5
• Poste télésurveillé : 8 touches mémoires M1 à M8 utilisables par appui sur une des touches 1 à 8 sansprendre la ligne.
• Poste non télésurveillé : 10 touches mémoires M0 à M9 utilisables par appui sur une des touches 0 à 9sans prendre la ligne.
DANS LES POSTES A CLAVIER, LA MEMOIRE M1 PEUT ETREAFFECTEE A LA TOUCHE
PROGRAMMATION DE LA TOUCHE
Pour affecter la touche à la mémoire M1 taper la combinaison suivante:
* 2 4 0 0 *
REMARQUE
NFC227A*TEL224 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
PROGRAMMATION DU TYPE DE NUMEROTATION DU POSTE
Taper une des combinaisons suivantes :
1/ Pour numérotation DTMF et raccroché automatiqueTaper la combinaison
* 1 0 0 2 *2/ Pour numérotation Décimale et raccroché automatique
Taper la combinaison
* 1 0 0 3 *3/ Pour supprimer le raccroché automatique (cas général du poste DTMF à combiné)
Taper la combinaison
* 1 0 0 6 *4/ Pour supprimer le raccroché automatique (cas général du poste Décimal à combiné)
Taper la combinaison
* 1 0 0 7 *
REGLAGE DU VOLUME DE RECEPTION (POSTE MAINS LIBRES)
Taper la combinaison suivante:
* 1 4 0 <V> *< V > Volume de 0 à 9 (réglage usine = 5)
Nota: En cas de distorsion dans le haut-parleur réduire le volume de réception à une valeurinférieure à celle préconisée.
REGLAGE DU VOLUME SONNERIE
Taper la combinaison suivante:
* 1 6 0 <V> *< V > Volume de 1 à 7(réglage usine = 7)
NFC227A*TEL225 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
PROGRAMMATION D’UN ENCHAINEMENT DE NUMEROS
Pour la programmation de plusieurs mémoires, taper :
* 5 0 0 <M> * # 1 1 # <N> *M = 1, 2, ...., 8 max
N = Numéro d’appel de 1 à 15 chiffres
L’enchaînement commence toujours avec la mémoire de base affectée au boutonet s’arrête sur la première mémoire vide.
Pour programmer une mémoire vide (ou effacer un numéro) il faut taper :
* 5 0 0 <M> * *
Vous devez obligatoirement programmer les tempos d’attente entre les mémoiresT1 entre M1-M2 etT2 entre M2-M3, M3-M4 etc.. si c’est le cas.
Ces tempos représentent les temps d’attente en cas de non réponse avant de passer au numérosuivant.
Pour T1 taper :
* 2 0 T T *TT représente la valeur de la tempo d’attente en secondes.Dans le cas d’un seul numéro programmé TT = 00Dans le cas d’un enchaînement de 2 ou plusieurs numéros, deux possibilités se présentent :
a) d’entendre ce qui se passe en ligne en programmant T1 à une valeur paire (30 sec. par ex.)
b) de cacher ce qui se passe en ligne (non réponse, occupation etc...) jusqu’au décroché ducorrespondant, par une simulation de sonnerie et clignotement de la led.Sur détection de la parole du correspondant appelé, un bip long annonce aux deux correspondantsl’établissement de la communication, la led passe en fixe.
Pour cela il faut programmer T1 à une valeur impaire (31 sec. par exemple).
Pour T2 taper :
* 2 1 T T *
NFC227A*TEL226 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
10 UTILISATION ET PROGRAMMATION DU POSTE TLS 227 A1C4A LANCEMENT TOUCHES MEMOIRES
PROGRAMMATION DES MEMOIRES :• à partir d’un poste distant, appeler le poste 227• lorsque le poste 227 sonne, décrocher le combiné• à partir du poste distant, entrer en programmation par le code utilisateur (*1234* par défaut), un bip est
émis par le poste 227• pour programmer la mémoire de la touche 1, faire *5001*xxxxxxxxxx* (ou les xxxxxxxxxx représentent
le numéro de la mémoire à lancer), un bip est émis par le poste 227• pour programmer la mémoire de la touche 2, faire *5002*xxxxxxxxxx* (ou les xxxxxxxxxx représentent
le numéro de la mémoire à lancer), un bip est émis par le poste 227• pour programmer la mémoire de la touche 3, faire *5003*xxxxxxxxxx* (ou les xxxxxxxxxx représentent
le numéro de la mémoire à lancer), un bip est émis par le poste 227• pour programmer la mémoire de la touche 4, faire *5004*xxxxxxxxxx* (ou les xxxxxxxxxx représentent
le numéro de la mémoire à lancer), un bip est émis par le poste 227• raccrocher le combiné du poste distant• raccrocher le combiné du poste 227
ESSAIS DE LANCEMENT DES MEMOIRES :Ø décrocher le combiné du poste 227Ø appuyer sur la touche 1 et vérifier que le poste numérote et appelle le bon numéroØ raccrocher le combiné du poste 227
Ø décrocher le combiné du poste 227Ø appuyer sur la touche 2 et vérifier que le poste numérote et appelle le bon numéroØ raccrocher le combiné du poste 227
Ø décrocher le combiné du poste 227Ø appuyer sur la touche 3 et vérifier que le poste numérote et appelle le bon numéroØ raccrocher le combiné du poste 227
Ø décrocher le combiné du poste 227Ø appuyer sur la touche 4 et vérifier que le poste numérote et appelle le bon numéroØ raccrocher le combiné du poste 227
NFC227A*TEL227 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
11 ENTRETIEN
Les postes téléphoniques type 227A1 n’ont pas besoin de beaucoup d’entretien pour rester enexcellente condition de fonctionnement.Effectuer l’entretien ci-dessous si nécessaire.
A L’EXTERIEUR
Nettoyer à l’aide d’un chiffon doux humecté d’eau, à l’exclusion de tous solvants.Si vous utilisez un Kärcher (50 bars de préférence),respecter une distance d’environ 1m50 entre leposte et la lance.
A L’INTERIEUR
L’intérieur du poste n’a pas besoin d’entretien.Ne pas verser de liquide dans le poste téléphonique.Veillez sur l’état des joints d’étanchéité et de leur bonne mise en place.
12 EN CAS DE PROBLEME
Avant de consulter le service après-vente, nous vous conseillons de vérifier les points suivants:
PROBLEME DE PRISE DE LIGNE OU DE NUMEROTATION
Ø Vérifier la connexion de la ligne téléphonique sur le bornier de raccordement (voir page 15).Ø Vérifier que le bouton n’est pas coincé par un objet étranger.
PROBLEME D’EMISSIONSi l’émission du poste est faible.
Ø vérifier que les trous du micro ne soient pas bouchés par un objet étranger.Ø Vérifier le réglage du cavalier ST1 (voir page 14).
PROBLEME DE RECEPTIONSi la réception téléphonique est faible.
Ø régler le volume de réception désiré (voir page 23).
Si après vérification des points mentionnés ci-dessus le problème persiste, veuillez retourner lematériel au fabricant à l’adresse suivante :
LE LAS34/36 RUE ROGER SALENGROF94134 FONTENAY SOUS BOIS - FRANCE
IMPORTANT
AUCUNE INTERVENTION OU MODIFICATION DE L’APPAREILPAR VOS SOINS N’EST AUTORISE SANS L’ACCORD DU FABRICANT.
NFC227A*TEL228 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
13 PROGRAMMATION EVOLUEE
• Le poste téléphonique peut être configuré, en local ou à distance, selon les besoins de l'utilisateurpar des codes de programmation. Les programmations les plus courantes sont décrites dans le § 9PROGRAMMATION DE BASE page 22.
• D’autres possibilités de programmation, offertes à l’utilisateur, sont évoquées dans le présentchapitre. Enfin des codes de télécommande permettant d'initier des actions particulières sontdécrites à la suite. D'une manière générale, tous ces codes sont à 4 chiffres encadrés par 2 étoiles(*), à l’exception des mémoires de numéros d'appel.
• Ces fonctions sont accessibles par un "code d'accès" préalable qui peut être personnalisé parl'utilisateur.
• Code programmation Statut:*10xx* Configuration matériel
A chaque fonction est affectée une valeur (xx): xx = 00 Numérotation DTMF xx = 01 Numérotation Décimale xx = 02 Pas d’accès mémoire direct xx = 04 Pas de raccroché sur tonalitéC’est la somme de ces valeurs qui détermine la configuration globale.Exemple:⇒ *1000* = Numérotation DTMF + accès mémoire 0 à 9 sur les touches correspondantes du clavier + raccroché automatique sur tonalité d’occupation⇒ *1007* = Numérotation Décimale + pas d’accès mémoire + pas de raccroché automatique
• Code programmation Sonnerie:*11xx* Nb Sonneries avant décroché
xx = 00 Pas de Sonnerie avant décroché jusqu'à xx = 98 98 Sonneries avant décroché Programmation usine xx = 99 Le poste ne décroche pas
Nota: 00 sonnerie, réservé à la station de télé-maintenance
• Code programmation TOnLine:*12xx* Durée de conversation avant raccroché auto
Programmation usine xx = 00 Le poste n’est pas limité en durée de conversation xx = 04 4 minutes avant raccroché auto jusqu'à xx = 99 99 minutes avant raccroché auto
NFC227A*TEL229 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
• Code programmation TSilence:*13xx* Durée de Silence admise avant raccroché auto
Programmation usine xx = 00 Le poste ne raccroche pas sur silence Exemple xx = 30 30 secondes avant raccroché auto jusqu'à xx = 99 99 secondes avant raccroché autoNota: les tonalités à fréquences stables cadencées ou non, sont prises pour du silence.
• Code programmation ModSon:*15xx* Type de Modulation de Sonnerie
Programmation usine xx = 00 Fréquence pure xx = 01 3 Fréquences mélangées
• Code programmation PBout:*17xx* Temps d'appui sur le bouton R (sans relâchement)
pour que la prise de ligne soit effective Programmation usine xx = 00 Prise de ligne immédiate jusqu'à xx = 98 Action différée de 9,8 secondes si xx = 99 Pas de prise de ligne par le bouton
L’USAGE DE L’ACCES MEMOIRE DIRECTE PAR LA TOUCHE R AINSI QUE LAMULTI-NUMEROTATION NE PEUVENT SE FAIRE QU’EN MODE MAIN LIBRE.
L’USAGE DU COMBINE N’EST POSSIBLE QU’APRES LE DECROCHE DU CORRESPONDANT
• Code programmation T1: MODE MULTI-NUMEROTATION*20xx* Temps en secondes pour le passage de M1 à M2 pour
enchaîner la numérotation automatique Programmation usine xx = 00 Pas d'enchaînement de numéros jusqu'à xx = 99 99 secondes sur M1 avant de passer à M2Nota: pendant un enchaînement de numéros, deux possibilités, si T1 est pair le haut parleur recopiela phonie de la ligne (retour d’appel, occupation, numérotation etc...). Si T1 est impair le hautparleur génère une tonalité de tranquillisation cadencée et le voyant clignote au même rythme.
• Code programmation T2: MODE MULTI-NUMEROTATION*21xx* Temps en secondes pour le passage de M2 à M3, M3
à M4, jusqu’à M8 pour enchaîner la numérotationautomatique
Programmation usine xx = 00 Pas d'enchaînement de numéros jusqu'à xx = 99 99 secondes sur Mx avant de passer au suivantNota: pendant l'enchaînement des numéros subordonnés à T2, c'est la parité de T1 qui détermine laphonie sur le haut parleur.
ATTENTION
NFC227A*TEL230 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
• Code programmation Flashing:*24xx* Durée en 1/100 ème de seconde du Flashing
Programmation usine xx = 27 270 mS de Flashing xx = 00 Pas de Flashing, la touche R devient mémoire directe
M1 jusqu'à xx = 99 990 mS de Flashing
• Code programmation MCAcces:*30xx* Millier et centaine du code d'accès utilisateur
Programmation usine xx = 12 12 xx = 10 Valeur minimum jusqu'à xx = 99 Valeur maximumNota: les milliers ne doivent jamais avoir pour valeur 0 (zéro).
• Code programmation DUAcces:*31xx* Dizaine et unité du code d'accès utilisateur
Programmation usine xx = 34 34 xx = 00 Valeur minimum jusqu'à xx = 99 Valeur maximumNota: le code d'accès utilisateur, comporte obligatoirement 4 chiffres, il peut prendre pour valeur de1000 à 9999. Il est donc programmé en 2 fois (30xx et 31xx).
LE CODE D’ACCES UTILISATEUR NE DOIT, NI COMMENCER PAR 0 (ZERO), NIETRE PERDU, DANS LE CAS CONTRAIRE L’ACCES A LA PROGRAMMATION
DEVIENT IMPOSSIBLE
• Code programmation CutLine:*32xx* Temps d'appui sur le bouton (sans relâchement)pour que
le raccroché de ligne soit effectif Programmation usine xx = 20 Action différée de 2 secondes xx = 00 Pas de raccroché par appui sur le bouton jusqu'à xx = 98 Action différée de 9,8 secondes si xx = 99 Pas de pause de ligne par le bouton.
• Code programmation TonMin:*34xx* Fréquence mini de tonalité de raccroché
Programmation usine xx = 30 300 Hz xx = 00 0 Hz jusqu'à xx = 99 990 Hz
ATTENTION
NFC227A*TEL231 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
• Code programmation TonMax:*35xx* Fréquence maxi de tonalité de raccroché
Programmation usine xx = 50 500 Hz xx = 00 0 Hz jusqu'à xx = 99 990 Hz
• Code programmation Mémoires:*50xx*
xx = 00 à 09 Selon la mémoire choisie suivi de #11# Recherche de tonalité ou #10# Pause de 2 secondes avant numérotation suivi de 1 à 15 chiffres Correspondant(s) au numéro souhaité terminé par * Terminateur de séquence Programmation usine Toutes mémoires vierges
Pour effacer une mémoire:*50xx*
xx = 00 à 09 Selon la mémoire choisie terminé par * Terminateur de séquence
CODES DE TELECOMMANDE
• Code télécommande Test:*97xx*
xx = 00 Test microphone et haut parleur Accusé de réception du poste: Emission pendant 1 seconde d'une fréquence de 1244 Hz suivi de Emission pendant 1 seconde d'une fréquence de 622 HzNota: à la suite de cette télécommande le haut parleur du poste est neutralisé.
• Code télécommande Effacement:*98xx*
xx = 00 Remise du poste en configuration usine Accusé de réception du poste: * Après 1, 3 seconde environ xx = 02 Effacement des mémoires M0 à M9
• Code télécommande Spécial:*99xx*
xx = 00 Raccroche le poste automatiquement xx = 01 Retour HP
Nota: cette télécommande est utile pour réactiver le haut parleur du poste alors que celui-ci a éténeutralisée par un test HP (*9700*).
**************
NFC227A*TEL232 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
NFC227A*TEL233 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
EXPLOSIONPROOF TELEPHONES 227A1 TYPE AND VARIANTS
1. PRESENTATION1.1 GENERAL FEATURES
EQUIPMENT FOR INDUSTRIAL SITES - EXPLOSIONPROOF TELEPHONESSERIES 227A1
MARKINGThe marking indicates following particulars :
• Address : LE LAS34/36 RUE ROGER SALENGROF94134 FONTENAY SOUS BOIS - FRANCE
• Marking : CE0080• Designation of type : 227A1• Year of construction : 200-
• Specific marking : II 2 G D• Complementary marking : em [ib] ib II CT5• Certificat of conformity : INERIS 03ATEX0118X• Ambient temperature of use : Tamb. = -40°C à +60°C• Voltage and current of use : see special conditions page 35
THIS PRODUCT CONFORMS TO WEATHERPROOF PROTECTIONCLASSIFICATION IP65
CAUTION!EACH AND EVERY COMPONENT PART IS INTEGRAL TO THE METHOD
OF PROTECTION AND CANNOT BE MODIFIED IN ANY WAY WHATSOEVER,INCLUDING THE CABLE ENTRIES.
THE GUARANTEE ONLY APPLIES WHERE THE PRODUCT IS INSTALLED AND OPERATED STRICTLYIN ACCORDANCE WITH INSTRUCTIONS AS DEFINED IN THIS MANUAL
NO GUARANTEE CAN BE INVOKED IN THE EVENT OF A DETERIORATION RESULTING FROMEXTERNAL FACTORS OR DUE TO LACK OF ADHERENCE TO USER INSTRUCTIONS
IN THE DESIRE FOR CONSTANT IMPROVEMENT, THE INFORMATION CONTAINED IN THISDOCUMENT AND THE CHARACTERISTICS OF THE EQUIPMENT MAY BE SUBJECT TO
MODIFICATIONS WIHTOUT PRIOR NOTICE
EUROPEAN STANDARDS
UNITS BEARING THE CODE "CE" CONFORM TO EMC DIRECTIVE (89/336/CEE)AND THE DIRECTIVE RELATING TO LOW VOLTAGES(73/23/EEC)
FORMULATED BY THE EUROPEAN COMMUNITY
UNITS BEARING THE CODE "E x" CONFORM TO ATEX DIRECTIVE (94/9CE)AND CONFORM TO EUROPEAN STANDARDS
EN 50 014 - 1997, EN 50 019 - 1994, EN 50 020-2002, EN 50 028 – 1987, EN 50 281 – 1998
The standards of the EN 50 XXX series are no longer those who are harmonized but that the equipmentconforms is not impacted by the substantial changes in the standards of the series EN 60079 and EN61241.
NOTE
NFC227A*TEL234 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.2 CONTENTS OF THE PACKAGE
The equipment you have just opened comprises:
• A telephone set• A user manual• Wallmounting kit Ref: GM208A12
1.3 GENERAL PRESENTATION OF SERIES 227A1 TELEPHONES
The telephone set is an explosionproof, wallmounted type , CB or ACB and comprises essentially:
• a casing protected to an enhanced level of safety, containing two intrinsically-safe printed circuit boardsand a set of electronic components, resin-coated and encapsulated. The coated printed circuit board hason its upper side two "e" terminals for connection of external electrical circuits.
• an intrinsically safe (IP65) telephone handset of light alloy
• an optional second receiver, also intrinsically safe
The front cover closes on to a weatherproof seal via 3 hollow hexagonal or special (optionally vandal-resistant) screws (M6) requiring a suitable key to undo them.
FEATURES
For all telephones types :
• Multifrequency (DTMF) and pulse dialling (for ACB type telephones)• Remote modification of settings from a typical DTMF telephone or from a maintenance station, for
example:Ø Ringing typeØ Ringing volumeØ Loudspeaker volumeØ Type of dialling
• Automatic cleardown capability• Offhook capability either immediately or after a programmable number of rings• Tone security protection - microphone operable after internal dialling
For Hands free telephones :
• Automatic cleardown capability.• Automatic answering capability or answering after a programmable number of rings.• « Tone security protection » (microphone operable only after called party answers)• Programming of stored numbers locally or via telephone line from any DTMF telephone.• Chained numbers if the called number is busy or does not answer after a programmable time.• Automatic off-hook
NFC227A*TEL235 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.4 USER INSTRUCTIONS FOR EXPLOSION-PROOF TELEPHONE
THE FIRST CUT OVER INTO SERVICE SHOULD BE CARRIED OUT BY ENGINEERS WITHADEQUATE AND APPROPRIATE TRAINING IN RESPECT OF HAZARDOUS AREAS.
IMPORTANT
ANY REPAIR OR MODIFICATION OF THE UNIT BY THE USER IS NOT ALLOWEDWITHOUT A FORMAL MANUFACTURER AGREMENT.
SET-UP / USAGE
The allowing instructions must be read in conjunction with :
1- standard NF C 15 100.2- standard EN 60 079-14 (electrical installations in gaseous explosive atmospheres).3- standard EN 60 079-17 (inspection and maintenance in hazardous environments).4- standard EN 50 281-1-2 (electrical equipment for use in the presence of inflammable dust. Part 1-2 :
encapsulated electrical equipment – selection, installation and maintenance).5- Decrees, orders laws directive, applications circulars, standards, rule – book and every other document
regarding the location of its installation.
Luch of observance of these element would not be our responsability. Installation of the equiment must becarred out by qualified competent experience staff.
You should ensur is compatibility between the indications figuring on the instruction plaque, the explosiveatmosphere present, the zone of voltage and the ambiant and surface temperatures.
MAINTENANCE INSTRUCTIONS
The following points should be checked at last once per
Ø The external equipment and the front panels must not be damaged.
Ø Check the terminals are tightly clamped, re cable if necessary.
Ø Before closing, check the seal housing, cleanliness, condition and its implementation.
Ø Secure the lid on the case and ensure that the 3 locking screws are tight.
Ø Check the tightening of the gland on the cable to ensure¬ watertightness.(Note: tow presses mounted on the apparatus group IIC are specific group of gases).
see special conditions page 36
NFC227A*TEL236 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.5 TECHNICAL FEATURES OF THE SERIES 227A1 TELEPHONESThe telephones operate without any modification to the PSTN lines. For perfect operation with a switch, it isnecessary to ensure that the following characteristics match those of the switch.In a case of incompatibility, special software can be provided. Contact the manufacturer for moreinformation.
• Ringing voltage Ringing duration = 1.5s + 0.5s Pause duration: 3s + 2s
> 35 Veff < U sonnerie < 80Veff CA 25 ou 50HzImax = 0.05 Aeff; Pmax = 1W
• Current in the telephone (off-hook position 35mA (20Ma minimum)Imax = 0.08ADC; Pmax = 1.2W
• Voltage on the telephone terminals (on-hook position)
48V (24V minimum) Umax = 60VDC
• Dialling system DTMF or pulse
• Dialling tone Frequency: 270Hz to 540HzDetection time min 2 sec
• Busy tone Sequence of beeps and pauses for more than 10 seconds Beep: 100ms to 600ms Pause: 100ms to 600ms
Frequency: 300Hz to 500HzDetection time 4-10sec
Must be equal to beep value
• Remote Ringing Tone Return Sequence of beeps and pauses until off- hook Beep: 0.2 sec to 1,6 sec. Beep + Pause: <6 sec
Frequency: 350Hz to 500Hz
• Cleardown Tone Sequence of beeps and pauses for more than 10 seconds Beep: 100ms to 600ms Pause: 100ms to 600ms
Frequency: 300 to 500HzDetection time 4-10 sec
Must be equal to beep value
1.6 SPECIAL CONDITIONS OF USE227A1 telephone set should be connected on a network line with the following particulars :
Ø Maximum voltage of use : Umax. = 60VdcØ Maximum delivered current : Imax. = 80mAØ Maximum delivered power : Pmax. = 1.2W
NFC227A*TEL237 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.7 DESCRIPTION OF TELEPHONES TYPE TLA 227A1A
Version TLA 227A1A is equipped with a 14-button keypad and operates solely in handset mode.
210
IS
G
F
D
A
240
117
83
CB
E
H
PLAQUE SIGNALETIQUE
A- Telephone Card Pulse/Tone Ref: WK221CMAATXB- Intrinsic Safety Card Ref: WK118PLIATXC- Keypad Card Ref: WK092CMAD- 2 Eex cable entries for cable Ø10-13mm Ref: EEL13C10*13ATXE- Light alloy handset Ref: MS436A13F- Mounting brackets, option Ref: GM337E2G- Second receiver, option Ref: MS533A2AH Piezo howler
NFC227A*TEL238 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.8 DESCRIPTION OF TELEPHONES TYPE TLC 227A1A
This version is CB (central battery) type without a keypad.
210
G
F
C
A
240
117
83
B
E
H
PLAQUE SIGNALETIQUE
A- Telephone Card Pulse/Tone Ref: WK221CMAATXB- Intrinsic Safety Card Ref: WK118PLIATXC- 2 Eex cable entries for cable Ø10-13mm Ref: EEL13C10*13ATXD- Light alloy handset Ref: MS436A13F- Mounting brackets, option Ref: GM337E2G- Second receiver, option Ref: MS533A2AH Piezo howler
NFC227A*TEL239 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.9 DESCRIPTION OF TELEPHONES TYPE TLA 227A1AT
Version TLA 227A1AT is equipped with a 15 button keypad plus a connect-to-line indicator and can operatein handset or hands-free mode. The latter mode can work with a maintenance station.
210
IS
H
G
D
A
240
117
83
CB
F
I
E
PLAQUE SIGNALETIQUE
A- Telephone Card Pulse/Tone Ref: WK221CMATATXB- Intrinsic Safety Card Ref: WK118PLIATXC- Keypad Card Ref: WK092CMAD- 2 Eex cable entries for cable Ø10-13mm Ref: EEL13C10*13ATXE- Electret type microphone Ref: CE515V2F- Light alloy handset Ref: MS436A13G- Mounting brackets, option Ref: GM337E2H- Second receiver, option Ref: MS533A2AI- Piezo loudspeaker
NFC227A*TEL240 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.10 DESCRIPTION OF TELEPHONES TYPE TLC 227A1AT
Version TLC 227A1AT is a CB-type telephone, it is equipped with a single-button connect-to-line indicatorand can operate in handset or hands-free mode. This version can work with a maintenance station.
210
H
G
D
A
240
117
83
CB
F
I
E
PLAQUE SIGNALETIQUE
A- Telephone Card Pulse/Tone Ref: WK221CMATATXB- Intrinsic Safety Card Ref: WK118PLIATXC- Keypad Card Ref: WK092CMAD- 2 Eex cable entries for cable Ø10-13mm Ref: EEL13C10*13ATXE- Electret type microphone Ref: CE515V2F- Light alloy handset Ref: MS436A13G- Mounting brackets, option Ref: GM337E2H- Second receiver, option Ref: MS533A2AI- Piezo loudspeaker
NFC227A*TEL241 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
1.11 DESCRIPTION OF KEYPAD
15 buttons weatherproof keypad with on-line reassurance indicator.A self-adhesive membrane placed between the buttons and the micro-contacts assures keypadweatherproofing.
SPECIAL BUTTON FOR ACCESSTO "STAR SERVICES"
CALL BUTTON
ON-LINEINDICATOR
LAST NUMBER REDIALNUMERO COMPOSE
RECALL
IS
NOTE : valid only for the hands free telephones set TLA227A1AT.Programming 10 direct memory access for keys 0 to 9 is allowed see chapter « autodial numbers M0 to M9 »page 48.
• Remotely checked phones : 8 memories M1 to M8 available by pushing keys 1 to 8 without pushing callbutton.
• Phones without remotely checked facility : 10 memories M0 to M9 by pushing keys 0 to 9 withoutpushing call button.
NOTE
THE RECALL BUTTON HAS A DOUBLE FUNCTIONS
ACCORDING TO PROGRAMMING:FLASHING OR ONE-TOUCH MÉMORY M1
NOTE:
Facility to use “R” and “BIS” keys as memory keys after going “off-hook”.
Ø When memory one is empty “R” key is used as a flashing key, otherwise “M1”value is dialled on line.
Ø When memory 2 is empty “BIS” key is used as a redial function, otherwise “M2”value is dialled on line.
NFC227A*TEL242 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
2. INSTALLATION OF 227A1 TELEPHONES
CUTOUT PLAN
NFC227A*TEL243 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
MIN MAX
MIN MAX
3. TELEPHONE CARD LAYOUT (REF.: WK221 CMAATX)
FUNCTIONS AND SETTINGS OF JUMPERS
PG 140B16
FUNCTIONS REF JUMPERSHANDS-FREE MICROPHONE SENSITIVITY• Sensitivity at 1 metre: place jumper on MAX• Sensitivity at 30 cm: place jumper on MIN
ST1
NOISE THRESHOLD SETTING• MIN setting: for quiet environment• MAX setting: for very noisy environmentNOTE: normal setting is carried out in the factory (according to design)
R28 MINMAX
NFC227A*TEL244 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
4. CONNECTION OF 227A1 TELEPHONES
4.1 OPENING THE TELEPHONE
To access the telephone circuit, unscrew the 3 fixing points on the front case using an ALLEN key #5.
4.2 CONNECTION OF THE TELEPHONE LINE
Connection of the telephone to the line is carried out on the intrinsic safety card WK118PLIATX via theconnector which can be embedded and lockable.
Connect the line to terminals L1 and L2 which are doubled to connect extensions.
4.3 EARTHING THE TELEPHONE
Electrical earthing is carried out externally via the earth screw (situated on the lower part of the case)referenced by the sign ⊥.
NFC227A*TEL245 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
5. USAGE OF TELEPHONES WITH KEYPAD TLA 227 A1A
The 227A1 unit is a telephone set, it will be used under the entire responsability of the user.
TO CALL
When the communication is finished, to release the line:
TO ANSWER A CALL
When the telephone rings
When the communication is finished, to release the line:
LAST NUMBER REDIAL
When the communications is finished, to release the line
I
LIFT THE HANDSET1
DIAL THE NUMBER2
REPLACE THE HANDSET3
LIFT THE HANDSET
1
DIAL THE NUMBER2
LIFT THE HANDSET
1
PRESS “Bis” or “LR”2
REPLACE THE HANDSET
3
NFC227A*TEL246 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
6. USAGE OF CB TELEPHONES TLC 227 A1A
The 227A1 unit is a telephone set, it will be used under the entire responsability of the user.
TO CALL
When the communication is finished, to release the line:
TO ANSWER A CALL
When the telephone rings
When the communication is finished, to release the line:
LIFT THE HANDSET1
REPLACE THE HANDSET
2
LIFT THE HANDSET1
REPLACE THE HANDSET
2
NFC227A*TEL247 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
7. USAGE OF TELEPHONES WITH KEYPAD TLA 227 A1AT
The 227A1 unit is a telephone set, it will be used under the entire responsability of the user.
• Operation of a telephone alternating from handset to hands-free with keypad:
- Lift handset ⇒ take line/handset- Push PL button ⇒ hands-free- Push PL button ⇒ handset- Replace handset ⇒ release lineor:- Lift handset ⇒ take line/handset- Push PL button ⇒ hands-free- Replace handset ⇒ hands-free- Push PL button ⇒ release lineor:- Push PL button ⇒ take line/hands-free- Lift handset ⇒ handset- Replace handset ⇒ hands-free- Push PL button ⇒ release line
If the handset is not replaced (vandalism, handset ripped out) the telephone remains operational hands-free
TO CALL
The red indicator comes on
When the called party responds, speak in front of the telephone from a distanceOf approximately 20cm or into the handset
When the communication is finished, to release the line:
The red indicator goes off
NOTE : Programming 10 direct memory access for keys 0 to 9 is allowed see chapter « autodial numbers M0to M9 » page 48.
PUSH THE CALL BUTTONOR LIFT THE HANDSET
DIAL THE NUMBER
PUSH THE CALL BUTTONOR REPLACE THE HANDSET
OR LIFT THE TELEPHONECLEAR DOWN AUTOMATICALLY
1
2
3
NFC227A*TEL248 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
TO ANSWER A CALL
When the telephone rings
The red indicator comes on
speak in front of the telephone from a distance Of approximately20cm or into the handset
When the communication is finished, to release the line:
The red indicator goes off
LAST NUMBER REDIAL
The red indicator comes on
When the called party responds, speak in front of the telephone from a distanceOf approximately 20cm or into the handset
When the communication is finished, to release the line:
The red indicator goes off
PUSH THE CALL BUTTONOR LIFT THE HANDSET
PUSH THE CALL BUTTONOR REPLACE THE HANDSET
OR LET THE TELEPHONECLEAR DOWN AUTOMATICALLY
1
2
PRESS “BIS” or LR2
I
PUSH THE CALL BUTTONOR LIFT THE HANDSET
1
PUSH THE CALL BUTTONOR REPLACE THE HANDSET
OR LET THE TELEPHONECLEAR DOWN AUTOMATICALLY
3
NFC227A*TEL249 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
FLASH RECALL
A programmed flash recall of 270ms takes placeLength of time of flash can be adjusted by programming
The R button has a double functions according to the programming : flashing or direct memory M1.(seechapter programming page 48) .
LENGTH OF CONVERSATION IS NOT LIMITED IN THE FACTORY.IT CAN BE CHANGED BY PROGRAMMING.
8. USAGE OF CB TELEPHONES TLC 227A1AT
The 227A1 unit is a telephone set, it will be used under the entire responsability of the user.
• Operation of a telephone alternating from handset to hands-free CB:
- Lift handset ⇒ take line/handset- Push PL button ⇒ hands-free- Push PL button ⇒ handset- Replace handset ⇒ release lineor:- Lift handset ⇒ take line/handset- Push PL button ⇒ hands-free- Replace handset ⇒ hands-free- Push PL button ⇒ release lineor:- Push PL button ⇒ take line/hands-free- Lift handset ⇒ handset- Replace handset ⇒ hands-free- Push PL button ⇒ release line
If the handset is not replaced (vandalism, handset ripped out) the telephone remains operational hands-free.
PRESS “R”
NOTE
NFC227A*TEL250 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
TO CALL
The red indicator comes on
When the called party responds, speak in front of the telephone from anapproximate distance of 20 cm or into the handset.
When the communication is finished, to release the line:
The red indicator goes off
TO ANSWER A CALL
When the telephone rings
The red indicator comes on
Speak in front of the telephone from an approximate distanceof 20 cm or into the handset.
When the communication is finished, to release the line:
The red indicator goes off
PUSH THE CALL BUTTONOR LIFT THE HANDSET
OR LET THE TELEPHONE
1
PUSH THE CALL BUTTONOR REPLACE THE HANDSET
OR LET THE TELEPHONECLEAR DOWN AUTOMATICALLY
2
PUSH THE CALL BUTTONOR LIFT THE HANDSET
1
PUSH THE CALL BUTTONOR REPLACE THE HANDSET
OR LET THE TELEPHONECLEAR DOWN AUTOMATICALLY
2
NFC227A*TEL251 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
9. BASIC PROGRAMMING
The sequence of buttons to be keyed on the keypad of a remote telephone, DTMF type, connected to thetelephone to be programmed.Take care during programming, the presence of busy tone can clear down the telephone automatically.IMPORTANT: Before any programming, key the access code :
* 1 2 3 4 *
AUTODIAL NUMBERS (M1)
Key the combinaison:
* 5 0 0 1 * # 1 1 # <N> *< N > autodial number from 1 to 15 digits.
During memory programming , the combination #11# represents the recognition of a continuous tone with afrequency of 440 Hz ± 100Hz (standard) before dialling.This is the standard for UK and many other countries but in some other countries #10# may be applicableinstead, whereby a 2-second pause is inserted rather than tone recognition.
AUTODIAL NUMBERS (M0 TO M9) (HANDS-FREE TELEPHONES)
Key the combinaison:
* 5 0 0 <M> * # 1 1 # <N> *< M > number of memory from 0 to 9 affected with the buttons 0 to 9
With the exception of the stations has two buttons or button 2 is affected at the M5.
• Remotely checked phones : 8 memories M1 to M8 available by pushing keys 1 to 8 without pushing callbutton.
• Phones without remotely checked facility : 10 memories M0 to M9 by pushing keys 0 to 9 withoutpushing call button.
NOTEFOR FULL KEYPAD TELEPHONE, THE MEMORY M1
CAN BE ALLOCATED TO THE BUTTON
PROGRAMMING OF THE « R » BUTTON
For full keypad telephone, to assigne button to memory M1 key the combinaison:
* 2 4 0 0 *
NFC227A*TEL252 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
PROGRAMMING THE TYPE OF DIALLING OF THE TELEPHONE
Key one of the following combinations:
1/ For DTMF dialling and automatic clear downKey the combinaison
* 1 0 0 2 *
2/ For pulse dialling and automatic cleardownKey the combinaison
* 1 0 0 3 *
3/ To suppress automatic cleardown (usual case for DTMF handset telephone)Key the combinaison
* 1 0 0 6 *
4/ To suppress automatic cleardown (usual case for pulse handset telephone)Key the combinaison
* 1 0 0 7 *
RECEIVE VOLUME ADJUSTMENT (HANDS-FREE TELEPHONES)
Key the following combination:
* 1 4 0 <V> *< V > Volume from 0 to 9 (factory setting = 5)
RINGING VOLUME ADJUSTMENT
Key the following combination:
* 1 6 0 <V> *< V > Volume from 1 to 7(factory setting = 7)
NFC227A*TEL253 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
PROGRAMME A NUMBER CHAIN (HANDS-FREE TELEPHONES)
For the programming of several memories, key the combinaisons:
* 5 0 0 <M> * # 1 1 # <N> *M (memory) = 1, 2, ...., 8 maxN= Call number up to 15 digits
The chain always starts with the basic storage assigned to the button and stop at the first empty memory.To program a memory empties (or to erase a number) it is necessary to type:
* 5 0 0 <M> * *
To program the interval between memory auto-dial attemptsT1 between M1 – M2 andT2 between M2 – M3, M3 – M4 etc… if necessary
These times are the intervals in the event of no-answerBefore dialling the next number.
For T1 key :
* 2 0 T T *TT is the time in seconds. If only one number TT=00
If chaining 2 or several numbers, 2 choices are possible :
a) to hear what actually happens on the line : program T1/T2 with even number (e.g., :30 sec)
b) to mask what happens on the line (no-answer, busy tone,…) until the called party picks up, by simulatingringing and flashing LED. On detection of speech from the called party, a long beep announces to both partiesthat the communication has been established, the LED shows constant. For this, program T1/T2 with an oddnumber (e.g. 31 sec.)
For T2 key :
* 2 1 T T *
NFC227A*TEL254 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
10. TLS 227 A1C4 USER MANUAL WITH MEMORY FACILITY
PROGRAMMING MEMORIES :
• From a distant unit call TLS227 unit• When the TLS227 rings, lift the handset• From the distant unit enter programming mode (def *1234*), and wait for the TLS227 acknowledge bip.• To programm memory 1, dial *5001*xxxxxxxxxx* (where xxxxxxxxxx is the phone number to be
dialed), a acknowledge bip will be send by TLS227.• To programm memory 2, dial *5002*xxxxxxxxxx* (where xxxxxxxxxx is the phone number to be
dialed), a acknowledge bip will be send by TLS227.• To programm memory 3, dial *5003*xxxxxxxxxx* (where xxxxxxxxxx is the phone number to be
dialed), a acknowledge bip will be send by TLS227.• To programm memory 4, dial *5004*xxxxxxxxxx* (where xxxxxxxxxx is the phone number to be
dialed), a acknowledge bip will be send by TLS227.• Go on-hook on both units.
TEST OF THE STORED MEMORIES :
Ø Go off-hookØ Press « 1 » button and check the called number is the right number.Ø Go on-hook
Ø Go off-hookØ Press « 2 » button and check the called number is the right number.Ø Go on-hook
Ø Go off-hookØ Press « 3 » button and check the called number is the right number.Ø Go on-hook
Ø Go off-hookØ Press « 4 » button and check the called number is the right number.Ø Go on-hook
NFC227A*TEL255 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
11. MAINTENANCE
Telephones type 227 require little maintenance to remain in excellent working order.Carry out the maintenance below if necessary.
EXTERNALLY
Clean with a soft damp rag.If a high-pressure water jet (preferably 50 bars) is used, this should be done with a distance of about 1m50between the telephone and the hose.
INTERNALLY
The interior of the telephone requires no maintenance. Do not pour any liquid into the telephone.Check the weatherproofing seals and that they are in place.
12. IN THE EVENT OF A PROBLEM
Before consulting the after-sales service, we advise you to check the following points:
LINE OR DIALLING PROBLEM
- Check the telephone line connection on the connector terminal (see page 41)- Check that the button is not jammed by a foreign object.
TRANSMISSION PROBLEM
- If transmission from the telephone is weak, check that the microphone holesare not blocked by a foreign object.
- Check the setting of the jumper ST1 (see page 40).
RECEPTION PROBLEM
- If telephone reception is weak, adjust the receive volume to the level required(see page 49).
After having checked the precedent points and if problem is not solved, please return the unit to themanufacturer at the following adress :
LE LAS34/36 RUE ROGER SALENGROF94134 FONTENAY SOUS BOIS - FRANCE
IMPORTANT
ANY REPAIR OR MODIFICATION OF THE UNIT BY THE USER IS NOT ALLOWEDWITHOUT A FORMAL MANUFACTURER AGREMENT.
NFC227A*TEL256 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
13. ADDITIONAL PROGRAMMING
• The telephone can be configured, locally or remotely, for user requirements by programming codes. Themost usual programming procedures are described in Section 8.1 Basic Programming on page 48.
• Other programming options, available to the user, are described in the present chapter. The remote-control codes facilitating particular functions are listed below. As a rule, all these codes are 4-digitsenveloped by two stars (*), with the exception of autodial number memories.
• These functions are accessed by an "access code" which can be specific to the user.
• Programming code STATUS
*10xx* Hardware configuration
For each function a value (xx) is designatedxx = 00 DTMF diallingxx = 01 Pulse diallingxx = 02 No direct memory accessxx = 04 No cleardown on tone
The sum of these values determines the overall configuration.
Example:
⇒ *1000* = DTMF dialling + access to memory 0-9 on keying the corresponding button on the keypad+ automatic cleardown on busy tone.
⇒ *1007* = Pulse dialling + no memory access + no automatic cleardown.
• Programming code Ringing
*11xx* Number of rings before auto-answerxx = 00 No ringing before auto-answer
Up to xx = 98 98 rings before auto-answer Factory setting xx = 99 The telephone does not auto-answer Note: 00 ringing, reserved for the remote diagnostics system.
• Programming code Time On-Line
*12xx* Duration of conversation before auto-cleardownFactory setting xx = 00 The telephone is not limited to any duration
xx = 04 Auto-cleardown after 4 minutesUp to xx = 99 Auto-cleardown after 99 minutes
NFC227A*TEL257 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
• Programming code Time Silence
*13xx* Length of Silence prior to auto-cleardownFactory setting xx = 00 The telephone does not clear down on silenceExample xx = 30 Auto-cleardown after 30 secondsUp to xx = 99 Auto-cleardown after 99 seconds
Note: steady frequency tones, whether cadenced or not, are taken as silence.
• Programming code Ring Modulation
*15xx* Type of ringing modulationFactory setting xx = 00 Pure frequency
xx = 01 Mixed frequencies
• Programming code Push Button
*17xx* Continuous time-button M pressed before line takenFactory setting xx = 00 Line taken immediatelyUp to xx = 98 Action deferred 9.8 seconds
If xx = 99 button disabled
DIRECT MEMORY ACCESS BY « R » BUTTON AND DIALLING CHAIN IS ONLYAVAILABLE IN HAND-FREE MODE
• Programming code T1: CHAINING MODE
*20xx* Time in seconds before passing from M1 to M2 to chain autodialling
Factory setting xx = 00 No number chainingUp to xx = 99 99 seconds on M1 before passing to M2
Note: during number chaining, there are two options - if T1 is an even number the loudspeaker reproducesthe telephony on the line (dialling-tone, busy, dialling etc…). If T1 is an odd number the loudspeakergenerates a cadenced calming tone and the indicator flashes to the same rhythm.
• Programming code T2: CHAINING MODE
*21xx* Time in seconds before passing from M2 to M3, M3 toM4, up to M8 to chain autodial numbers
Factory setting xx = 00 No number chainingUp to xx = 99 99 seconds on MX before passing to the next
Note: during the chaining of numbers in T2, it is the parity of T1 which determines the telephony on theloudspeaker.
ATTENTION
NFC227A*TEL258 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
Programming code Flashing
*24xx* Duration of Flashing in hundredths of a secondFactory setting xx = 27 270mS of Flashing
xx = 00 No Flashing, button R becomes direct memory M1Up to xx = 99 990mS of Flashing
• Programming code TH Access
*30xx* Thousands/hundreds of User Access CodeFactory setting xx = 12 12
xx = 10 Minimum valueUp to xx = 99 Maximum value
Note: The Thousands must never have 0 (zero) as a value.
• Programming code TU Access
*31xx* Tens and units of User Access CodeFactory setting xx = 34 34
xx = 00 Minimum valueUp to xx = 99 Maximum value
Note: the User Access Code must comprise 4 digits, its value can be between 1000 and 9999. It istherefore programmed in 2 steps (30xx and 31xx).
CAUTION!
The User ACCESS CODE must neither begin with 0 (zero)nor be lost or access to programming will be impossible.
• Programming Code Cut Line
*32xx* Continuous time button to be pressed for line cleardownFactory setting xx = 20 Action deferred 2 seconds
xx = 00 No cleardown by pressing buttonUp to xx = 98 Action deferred 9.8 secondsIf xx = 99 Cleardown disabled
• Programming code MinTone
*34xx* Minimum cleardown tone frequencyFactory setting xx = 30 300 Hz
xx = 00 0 HzUp to xx = 99 990 Hz
• Programming code MaxTone
*35xx* Maximum cleardown tone frequencyFactory setting xx = 50 500 Hz
xx = 00 0 HzUp to xx = 99 990 Hz
NFC227A*TEL259 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
• Programming code Memories
*50xx*xx = 00 to 09 According to memory selected
followed by #11# Seeks toneor #10# 2-second pause before diallingfollowed by 1 to 15 digits Desired Autodial numberterminated by * Sequence terminatorFactory setting All memories blank
To erase a memory:
*50xx*xx = 00 to 09 According to memory selected
terminated by * Sequence terminator
REMOTE CONTROL CODES
• Remote control code Test
*97xx*xx = 00 Test microphone and loudspeaker
Telephone acknowledgement:1-second transmission of frequency of 1244Hz
followed by:1-second transmission of frequency of 622Hz
Note: at the end of this remote control sequence the telephone loudspeaker is cut.
• Remote control code Erase
*98xx*xx = 00 Return telephone to factory setting
Telephone acknowledgement: * After about 1.3 secxx = 02 Memories M0-M9 erased
• Remote control code Special
*99xx*xx = 00 Clear down the telephone automaticallyxx = 01 Reinstate loudspeaker
Note: this remote control code is used to reactivate the telephone loudspeaker when it has been cut by aloudspeaker test (*9700*)
NFC227A*TEL260 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
NFC227A*TEL261 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
NFC227A*TEL262 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
NFC227A*TEL263 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
NOTES
NFC227A*TEL264 /64
\\SERVEUR MAX\\ Notices NFC \ NFC227 TL2 \ NFC227A-TEL2.DOC
GROUPE LE LAS - PARIS
FRANCE34/36 RUE ROGER SALENGROF 94134 FONTENAY SOUS BOIS
Tel : 33 01 48 76 62 62Fax : 33 01 48 76 83 04Internet : www.lelas.frE-mail : [email protected]
BELGIQUEBD BRACOPS 205/1B. 1070 BRUXELLESTel : 00 32 25 22 83 66Fax : 00 32 25 27 83 14
E-mail : [email protected]
ENGLANDSAFE COMMUNICATIONS LTD
BANK HOUSE - SOUTHWICK SQUARESOUTHWICK
U.K BRIGHTON W. SUSSEX BN 42 4 FNTel : 00 44 12 73 87 14 00Fax : 00 44 12 73 59 66 00
E-mail : [email protected]
ITALYTELEINDUSTRIA SRL
VIA PALERMO, 12I. 20090 ASSAGO (MI)
Tel : 00 39 02 45 71 37 29Fax : 00 39 02 45 71 40 00
Internet : www.teleindustria.comE-mail : [email protected]
Edition H : 02.11.2009