toppage lc-40/46lx814e, lc-40/46lu824e … lc-40/46lu824e i lc-40/46lx814e, lc-40/46lu824e outline...
TRANSCRIPT
SERVICE MANUAL
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining thesafety and performance of the set.
This document has been published to be used forafter sales service only.The contents are subject to change without notice.
OUTLINE AND DIFFERENCES FROM BASE MODELOUTLINE.................................................................... iDIFFERENCES FROM BASE MODEL (LC-40LX814E) .......................................................... iDIFFERENCES FROM BASE MODEL (LC-46LX814E) .......................................................... iDIFFERENCES FROM BASE MODEL (LC-40LU824E) ......................................................... iiDIFFERENCES FROM BASE MODEL (LC-46LU824E) ......................................................... ii
SAFETY PRECAUTIONIMPORTANT SERVICE SAFETY PRECAUTION...........................................................iiiPrecautions for using lead-free solder ..................... ivEnd of life disposal .................................................... v
OUTLINEMAJOR SERVICE PARTS ....................................... vi
Parts Guide
TopPage
CONTENTS
LCD COLOUR TELEVISION
No. S00N840LX814E
LC-40/46LX814E, LC-40/46LU824E
LC-40LX814ELC-46LX814ELC-40LU824ELC-46LU824EMODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its orig-inal condition and only parts identical to those specified should be used.
OUTLINEThis Service Manual covers the differences from LC-40/46LE814E, LC-40/46LE824E.For other technical information, refer to the LC-40/46LE814E, LC-40/46LE824E (No. S90K840LE814E) ServiceManual.
LC-40/46LX814E, LC-40/46LU824E
LC-40/46LX814E, LC-40/46LU824E Service ManualOUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINEThis Service Manual covers the differences from LC-40/46LE814E, LC-40/46LE824E.
For other technical information, refer to the LC-40/46LE814E, LC-40/46LE824E (No. S90K840LE814E) Service Manual.
DIFFERENCES FROM BASE MODEL (LC-40LX814E)
DIFFERENCES FROM BASE MODEL (LC-46LX814E)
Ref No. Description LC-40LE814E (No. S90K840LE814E)
LC-40LX814E(No. S00N840LX814E) Interchangeability Note
PRINTED WIRING BOARD ASSEMBLIESN MAIN Unit DKEYDF455FM11 ← — No changeN ICON Unit DUNTKF493FM03 ← — No changeN R/C, LED Unit DUNTKF494FM02 ← — No changeN POWER/LED CONTROL Unit RUNTKA685WJQZ ← — No changeN TOUCH SENSOR Unit RUNTKA692WJQZ ← — No changeN LCD CONTROL Unit RUNTK4512TPZC ← — No change
LCD PANEL MODULEN 40” LCD Panel Module Unit R1LK400D3LWF2Y ← — No change
CABINET PARTS1 Front Cabinet Ass'y CCABAC527WJ1A CCABAC527WJ1C D Changed
Ref No. Description LC-46LE814E (No. S90K840LE814E)
LC-46LX814E(No. S00N840LX814E) Interchangeability Note
PRINTED WIRING BOARD ASSEMBLIESN MAIN Unit DKEYDF455FM11 ← — No changeN ICON Unit DUNTKF493FM03 ← — No changeN R/C, LED Unit DUNTKF494FM02 ← — No changeN POWER/LED CONTROL Unit RUNTKA686WJQZ ← — No changeN TOUCH SENSOR Unit RUNTKA692WJQZ ← — No changeN LCD CONTROL Unit RUNTK4512TPZG ← — No change
LCD PANEL MODULEN 46” LCD Panel Module Unit R1LK460D3LWG2Y ← — No change
CABINET PARTS1 Front Cabinet Ass'y CCABAC528WJ1A CCABAC528WJ1C D Changed
i
LC-40/46LX814E, LC-40/46LU824E
DIFFERENCES FROM BASE MODEL (LC-40LU824E)DIFFERENCES FROM BASE MODEL (LC-46LU824E)
Ref No. Description LC-40LE824E (No. S90K840LE814E)
LC-40LU824E(No. S00N840LX814E) Interchangeability Note
PRINTED WIRING BOARD ASSEMBLIESN MAIN Unit DKEYDF455FM12 ← — No changeN ICON Unit DUNTKF493FM03 ← — No changeN LOGO Unit DUNTKF493FM04 ← — No changeN R/C, LED Unit DUNTKF494FM02 ← — No changeN POWER/LED CONTROL Unit RUNTKA685WJQZ ← — No changeN TOUCH SENSOR Unit RUNTKA761WJQZ ← — No changeN LCD CONTROL Unit RUNTK4512TPZC ← — No change
LCD PANEL MODULEN 40” LCD Panel Module Unit R1LK400D3LWF0Y ← — No change
CABINET PARTS1 Front Cabinet Ass'y CCABAC621WJ12 CCABAC621WJ13 D Changed
Ref No. Description LC-46LE824E (No. S90K840LE814E)
LC-46LU824E(No. S00N840LX814E) Interchangeability Note
PRINTED WIRING BOARD ASSEMBLIESN MAIN Unit DKEYDF455FM12 ← — No changeN ICON Unit DUNTKF493FM03 ← — No changeN LOGO Unit DUNTKF493FM04 ← — No changeN R/C, LED Unit DUNTKF494FM02 ← — No changeN POWER/LED CONTROL Unit RUNTKA686WJQZ ← — No changeN TOUCH SENSOR Unit RUNTKA761WJQZ ← — No changeN LCD CONTROL Unit RUNTK4512TPZG ← — No change
LCD PANEL MODULEN 46” LCD Panel Module Unit R1LK460D3LWG0Y ← — No change
CABINET PARTS1 Front Cabinet Ass'y CCABAC612WJ12 CCABAC612WJ13 D Changed
Interchangeability
Completely interchangeableA: = NEWOLD
Interchangeable from
OLD to NEWB: NEWOLD
Interchangeable from
NEW to OLDC: NEW OLD
Not interchangeableD: X OLDNEW
ii
LC-40/46LX814E, LC-40/46LU824E
LC-40/46LX814E, LC-40/46LU824E Service ManualSAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)Before returning the receiver to the user, perform the followingsafety checks:
3. Inspect all lead dress to make certain that leads are not pinched,and check that hardware is not lodged between the chassis andother metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,insulation materials, cabinet backs, adjustment and compartmentcovers or shields, isolation resistor-capacitor networks, mechanicalinsulators, etc.
5. To be sure that no shock hazard exists, check for leakage current inthe following manner.
• Plug the AC cord directly into a 220~240 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-leled by a 0.15µF capacitor in series with all exposed metal cabinetparts and a known earth ground, such as electrical conduit or elec-trical ground connected to an earth ground.
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having areturn to the chassis (antenna, metal cabinet, screw heads, knobsand control shafts, escutcheon, etc.) and measure the AC voltagedrop across the resistor.All checks must be repeated with the AC cord plug connectionreversed. (If necessary, a nonpolarized adaptor plug must be usedonly for the purpose of completing these checks.)Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.)or more is excessive and indicates a potential shock hazard whichmust be corrected before returning the monitor to the owner.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICEMany electrical and mechanical parts in LCD colour television havespecial safety-related characteristics.
These characteristics are often not evident from visual inspection, norcan protection afforded by them be necessarily increased by usingreplacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics areidentified in this manual; electrical components having such featuresare identified by “ ” and shaded areas in the Replacement PartsList and Schematic Diagrams.
For continued protection, replacement parts must be identical to thoseused in the original circuit.
The use of a substitute replacement parts which do not have the samesafety characteristics as the factory recommended replacement partsshown in this service manual, may create shock, fire or other hazards.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
CAUTION:
FOR CONTINUED PROTECTION AGAINST A
RISK OF FIRE REPLACE ONLY WITH SAME
TYPE FUSE.
40 inch model: F7000, F7001 (3.15A/250V)
46 inch model: F7000, F7001 (5A/250V)
DVM
AC SCALE
1.5k ohm10W
TO EXPOSEDMETAL PARTS
CONNECT TOKNOWN EARTHGROUND
0.15 µF
TEST PROBE
iii
LC-40/46LX814E, LC-40/46LU824E
Precautions for using lead-free solderEmploying lead-free solder• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
Using lead-free wire solder• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause dam-
age or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated solderingbit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering• As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may bepeeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm thesteady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit asrequired.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No. Description CodeZHNDAi123250E J φ0.3mm 250g (1roll) BLZHNDAi126500E J φ0.6mm 500g (1roll) BKZHNDAi12801KE J φ1.0mm 1kg (1roll) BM
L F a
Indicates lead-free solder of tin, silver and copper.
L F a/a
Indicates lead-free solder of tin, silver and copper.
iv
LC-40/46LX814E, LC-40/46LU824E
End of life disposalEnd of life disposal
v
LC-40/46LX814E, LC-40/46LU824E
LC-40/46LX814E, LC-40/46LU824E Service ManualOUTLINE
MAJOR SERVICE PARTS
PWB UNIT
NOTE: (*1) Replace MAIN Unit (DKEYDF455FM11, DKEYDF455FM12) in case of IC8401 or IC3302 failure.
(*2) TOUCH SENSOR Unit (RUNTKA761WJQZ) reuse will be impossible, once it is stuck on front cabinet and exfoliates.
Therefore, please exchange of a TOUCH SENSOR Unit in the case of front cabinet exchange.
OTHER UNIT
IC FOR EXCLUSIVE USE OF THE SERVICE
SERVICE JIGS
Ref No. Parts Code DescriptionN DKEYDF455FM11 MAIN Unit (LC-40LX814E)(LC-46LX814E) (*1)N DKEYDF455FM12 MAIN Unit (LC-40LU824E)(LC-46LU824E) (*1)N DUNTKF493FM03 ICON UnitN DUNTKF493FM04 LOGO Unit (LC-40LU824E)(LC-46LU824E)N DUNTKF494FM02 R/C, LED UnitN RUNTKA685WJQZ POWER/LED CONTROL Unit (LC-40LX814E)(LC-40LU824E)N RUNTKA686WJQZ POWER/LED CONTROL Unit (LC-46LX814E)(LC-46LU824E)N RUNTKA692WJQZ TOUCH SENSOR Unit (LC-40LX814E)(LC-46LX814E)N RUNTKA761WJQZ TOUCH SENSOR Unit (LC-40LU824E)(LC-46LU824E) (*2)N RUNTK4512TPZC LCD CONTROL Unit (LC-40LX814E)(LC-40LU824E)N RUNTK4512TPZG LCD CONTROL Unit (LC-46LX814E)(LC-46LU824E)
Ref No. Parts Code DescriptionN R1LK400D3LWF2Y 40” LCD Panel Module Unit (LC-40LX814E)N R1LK460D3LWG2Y 46” LCD Panel Module Unit (LC-46LX814E)N R1LK400D3LWF0Y 40” LCD Panel Module Unit (LC-40LU824E)N R1LK460D3LWG0Y 46” LCD Panel Module Unit (LC-46LU824E)
Ref No. Parts Code Description Q’tyIC501 RH-iXD108WJQZS IC (EDID for PC) 1
IC2002 RH-iXC786WJNJQ IC (Monitor MICON) 1
Ref No. Parts Code Description Q’tyN QCNW-G616WJQZ Main Unit to LCD Control Unit (LW) 1N QCNW-G625WJQZ LCD Control Unit to Power Unit (PL) 1N QCNW-H184WJQZ Main Unit to Power Unit (PD) 1N QCNW-H185WJQZ Main Unit to Power Unit (LB) 1N QCNW-K594WJQZ Main Unit to R/C, LED Unit (RA) 1N QCNW-K595WJQZ Main Unit to Speaker (SP) 1N QCNW-K596WJQZ Main Unit to LOGO Unit (RL) (LC-40LU824E)(LC-46LU824E) 1N QCNW-K597WJQZ Main Unit to Woofer (SB) 1
vi
LC-40/46LX814E, LC-40/46LU824E
vii
LC-40/46LX814E, LC-40/46LU824E
PartsGuidePARTS GUIDE
CONTENTS
No. S00N840LX814E
LCD COLOUR TELEVISION
LC-40LX814ELC-46LX814ELC-40LU824ELC-46LU824EMODELS
[1] PRINTED WIRING BOARD ASSEMBLIES
[2] LCD PANEL MODULE
[3] CABINET PARTS (LC-40LX814E)
[4] CABINET PARTS (LC-46LX814E)
[5] CABINET PARTS (LC-40LU824E)
[6] CABINET PARTS (LC-46LU824E)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace theseparts with specified ones for maintaining the safety and performance of the set.
This document has been published to be usedfor after sales service only.The contents are subject to change without notice.
LC-40/46LX814E, LC-40/46LU824EPRICE NEW PART
NO. PARTS CODE RANK MARK DELIVERY DESCRIPTION[1] PRINTED WIRING BOARD ASSEMBLIESN DKEYDF455FM11 CG N P MAIN Unit (LC-40LX814E)(LC-46LX814E)N DKEYDF455FM12 CL N P MAIN Unit (LC-40LU824E)(LC-46LU824E)N DUNTKF493FM03 AM N P ICON UnitN DUNTKF493FM04 AN N P LOGO Unit (LC-40LU824E)(LC-46LU824E)N DUNTKF494FM02 AP N P R/C, LED Unit
! N RUNTKA685WJQZ BT N P POWER/LED CONTROL Unit (LC-40LX814E)(LC-40LU824E)! N RUNTKA686WJQZ BV N P POWER/LED CONTROL Unit (LC-46LX814E)(LC-46LU824E)
N RUNTKA692WJQZ AU N P TOUCH SENSOR Unit (LC-40LX814E)(LC-46LX814E)N RUNTKA761WJQZ BC N P TOUCH SENSOR Unit (LC-40LU824E)(LC-46LU824E)N RUNTK4512TPZC CA P LCD CONTROL Unit (LC-40LX814E)(LC-40LU824E)N RUNTK4512TPZG N P LCD CONTROL Unit (LC-46LX814E)(LC-46LU824E)
[2] LCD PANEL MODULEN R1LK400D3LWF2Y DM N P 40" LCD Panel Module Unit (LC-40LX814E)N R1LK460D3LWG2Y DV N P 46" LCD Panel Module Unit (LC-46LX814E)N R1LK400D3LWF0Y DM N P 40" LCD Panel Module Unit (LC-40LU824E)N R1LK460D3LWG0Y DX N P 46" LCD Panel Module Unit (LC-46LU824E)
2
LC-40/46LX814E, LC-40/46LU824E
[3] CABINET PARTS (LC-40LX814E)
48
4641
15
5
20
40
46
32
2-3
2-2
39
39 33
25
13
11
4444
14
44
1251
51
10
44
44
44
44
4517
45
4414
44
23
22
1716
17
44
2729
53
18
7
44
44
44
56
21
21 65
28
36
631
30
37
35
8
2644
16
16
9
16
4
1644
44
44
44
44
38
38
46
19
47
2
2-4
2-9
2-9
2-7
2-6
2-8
2-1
2-5
59
61
G
k
a
L
J
B
j
F
G
E
40" LCDPanel Module Unit
gf
h
K
POWER Unit
F
n
m
g
f
j
E
k
h
m
na
MAINUnit
db
p
K
C
C
B
X3X3
X2
X1A
AX1
X3
Note:
Be sure to attach this insulation sheet. (Ref No. 2-6, 25, 53)
Otherwise there is a risk of electric shock.
Z Z
1-11
R/C,LED Unit
TOUCHSENSORUnit
d ICONUnitp
b
L
J
1-2
1-3
58
63
64
52
52
50
3
LC-40/46LX814E, LC-40/46LU824E
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[3] CABINET PARTS (LC-40LX814E)1 CCABAC527WJ1C N P Front Cabinet Ass'y
4
LC-40/46LX814E, LC-40/46LU824E
[4] CABINET PARTS (LC-46LX814E)
48
50
43
16
48
2149
74
74
5
72
48
40
46
40
17
952
46
4617
4
4617
22
42
37
46
31
2933
57
7
39
23
6
46
30
38
34
32
46
46
71
70
73
66
69
67
68
23
828
46
1-1
41
41 35
47
47
46
13
46
19
19 12
46
46
10
55
47
2524
11
46 46
19
19
19
1946
15
14
46
27
46
46
46
61
65
63
64
B
G
h
F
k
j
POWERUnit
g
f
m
MAINUnit
h
db
p
Z
k
a
E
K m
a
L
CC
46" LCDPanel Module Unit
j
Y
G
gf
B F
J
E
K
X3X3
X1
X2A
AX1
X3
Note:
Be sure to attach this insulation sheet. (Ref No. 27, 57, 71)
Otherwise there is a risk of electric shock.
Z
Y
1
R/C,LED Unit
TOUCHSENSORUnit
dICONUnitp
b
L
J
1-2
1-3
58
59
60
18
51
51
53
53
5
LC-40/46LX814E, LC-40/46LU824E
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[4] CABINET PARTS (LC-46LX814E)1 CCABAC528WJ1C N P Front Cabinet Ass'y
6
LC-40/46LX814E, LC-40/46LU824E
[5] CABINET PARTS (LC-40LU824E)
48
4641
15
5
20
40
46
32
2-3
2-2
39
39 33
1-4
1-5
1-13
25
13
11
4444
14
44
12
10
44
44
44
44
4517
45
4414
44
23
22
49
49
1716
17
44
2729
53
7
44
44
44
56
21
21 65
28
36
631
30
34
37
35
8
2644
16
16
9
16
4
1644
44
44
44
44
38
38
46
19
47
2
2-4
2-9
2-9
2-7
2-6
2-8
2-1
2-5
59
61
G
k
a
L
H
L
R/C, LED Unit
LOGOUnit
ICONUnit b
dTOUCHSENSORUnit
e
p
J
J
H
B
j
F
G
E
40" LCDPanel Module Unit
gf
h
K
POWERUnit
F
n
m
g
f
j
E
k
h
m
na
MAINUnit
db
e
p
K
C
C
B
X3X3
X2
X1A
AX1
X3
Note:
Be sure to attach this insulation sheet. (Ref No. 2-6, 25, 53)
Otherwise there is a risk of electric shock.
1-5
1-5
1-5
1-5
Z Z
54
55
58
63
64
18
51
5152
52
50
1
7
LC-40/46LX814E, LC-40/46LU824E
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[5] CABINET PARTS (LC-40LU824E)1 CCABAC621WJ13 N P Front Cabinet Ass'y
8
LC-40/46LX814E, LC-40/46LU824E
[6] CABINET PARTS (LC-46LU824E)
48
50
43
16
48
2149
74
74
5
72
48
40
46
40
17
952
46
4617
4
4617
22
42
37
46
31
2933
57
7
39
23
6
46
30
38
34
32
36
46
60
46
71
70
73
66
69
67
68
23
828
46
1-4
1-5 1-5
1-53
59
1-1 41
41 35
47
47
46
46
13
46
19
19 12
46
46
10
55
47
2524
11
46 46
19
19
19
51
51
1946
15
14
54
54
46
27
56
46
46
46
61
65
63
64
B
G
h
F
k
j
POWERUnit
g
f
m
MAINUnit h
db
p
Z
k
a
e
E
K m
J
H
J
L
LOGOUnit ICON
Unit
e
p R/C, LED Unitb
d TOUCHSENSORUnit
a
L
CC
46" LCDPanel Module Unit
j
Y
G
gf
B F
H
E
K
X3X3
X1
X2A
AX1
X3
Note:
Be sure to attach this insulation sheet. (Ref No. 27, 57, 71)
Otherwise there is a risk of electric shock.
Z
Y
62
44
45
58
18
53
53
1
9
LC-40/46LX814E, LC-40/46LU824E
NO. PARTS CODE PRICE RANK
NEW MARK
PART DELIVERY DESCRIPTION
[6] CABINET PARTS (LC-46LU824E)1 CCABAC612WJ13 N P Front Cabinet Ass'y
10
LC-40/46LX814E, LC-40/46LU824E
No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.
COPYRIGHT © XXXX BYSHARP CORPORATION
ALL RIGHTS RESERVED.
MEMO
LC-
SHARP CORPORATIONAV Systems GroupCS Promotion CenterYaita, Tochigi 329-2193, Japan
Oct. 2010SH. KD
COPYRIGHT 2010 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.
40/46LX814E, LC-40/46LU824E