Hydraulic motors used on a Tomahawk 4040, 5050, 606 & 6060 Belt Drive & Tomahawk 8080 Bed Chain Motor

Adan 400cc AWMR (HYD5203) motors were exclusively used until July 2002.

Seal Kit for Adan AWMR motors is HYD4881 Comer / Geolink 400cc GFSL (HYD5203) After July 2002 we used either Adan Motors or the motors shown below. The Comer, Geolink and M&S motors used are all made by the same motor manufacturer but are fitted with different labels. They are easily identified by the fact that they have a 4 bolt mounting flange.

or M&S Hydraulic 400cc EPML (HYD5203)

Seal Kit for Comer / Geolink GFSL & M&S EPML motors is HYD4884

2 bolt fixing

‘Adan’ on end label Stamped in end ‘WMR 400 E’

4 bolt fixing Either ‘Geolink’ or ‘Comer Industries’ on end label ‘GFSL 400’ and ‘code 7.884400001’ printed on label Stamped in end 5 digit serial number eg ‘01006’

4 bolt fixing

‘M & S Hydraulic’ on end label ‘EPML’ printed on label Stamped in end ‘400 CO’

M&S Hydraulic 400cc MPN (HYD5203) After August 2008 a change was made to M & S MPN 400cc motors as shown below. These can be identified due to them having a 2 bolt mounting flange.

Seal Kit for M & S MPN motors is HYD4885 SAM Hydraulik 400cc BG HPS (HYD5234) A change has since been made to SAM Hydraulik motors. These can be identified due to them having an embossed ‘sh’ on the motor casting and a 25mm as opposed to 1 inch diameter output shaft.

Seal Kit for SAM Hydraulik BG HPS motors is HYD4891

‘M & S Hydraulic’ on end label ‘MP N’ stamped in label ‘400 COD’ stamped in label

2 bolt fixing

‘sh’ embossed on motor casting

25mm diameter output shaft

‘SAM Hydraulik’ on end label ‘BG 400’ stamped in label

Hydraulic motors used on a Tomahawk 404 & 505 Belt Drive & Tomahawk 808 Bed Chain Motor

Adan 200cc AWMR (HYD5202) motors were exclusively used until July 2002.

Seal Kit for Adan AWMR motors is HYD4881 Comer / Geolink 200cc GFSL (HYD5202) After July 2002 we used either Adan Motors or the motors shown below. The Comer, Geolink and M&S motors used are all made by the same motor manufacturer but are fitted with different labels. They are easily identified by the fact that they have a 4 bolt mounting flange.

or M&S Hydraulic 200cc EPML (HYD5202)

Seal Kit for Comer / Geolink GFSL & M&S EPML motors is HYD4884

2 bolt fixing ‘Adan’ on end label Stamped in end ‘WMR 200 E’

4 bolt fixing Either ‘Geolink’ or ‘Comer Industries’ on end label ‘GFSL 200’ and ‘code 7.882400002’ printed on label Stamped in end 5 digit serial number eg ‘01006’

4 bolt fixing

‘M & S Hydraulic’ on end label ‘EPML’ printed on label Stamped in end “200 CO”

M&S Hydraulic 200cc MPN (HYD5202) After August 2008 a change was made to M & S MPN 200cc motors as shown below. These can be identified due to them having a 2 bolt mounting flange.

Seal Kit for M & S MPN motors is HYD4885 SAM Hydraulik 200cc BG HPS (HYD5232) A change has since been made to SAM Hydraulik motors. These can be identified due to them having an embossed ‘sh’ on the motor casting and a 25mm as opposed to 1 inch diameter output shaft.

Seal Kit for SAM Hydraulik BG HPS motors is HYD4891

‘M & S Hydraulic’ on end label ‘MP N’ stamped on label ‘200 COD’ stamped on label

2 bolt fixing

25mm diameter output shaft

‘sh’ embossed on motor casting ‘SAM Hydraulik’ on end label

‘200’ stamped in label

Hydraulic motors used on a Tomahawk 8080 & 808S to swivel chute,on Tomahawk 9090 Bed Chain Gearbox and Spiromix Concrete Mixers

Adan 100cc (HYD5201) or 200cc AWMR (HYD5202) motors were exclusively used until July 2002

Seal Kit for Adan AWMR motors is HYD4881 Comer / Geolink 100cc (HYD5201) or 200cc GFS (HYD5207) After July 2002 we used either Adan Motors or the motors shown below. The Comer, Geolink and M&S motors used are all made by the same motor manufacturer but are fitted with different labels.

or M&S Hydraulic 100cc (HYD5201) or 200cc EPM (HYD5207)

Seal Kit for Comer / Geolink GFS & M&S EPM motors is HYD4885

2 bolt fixing ‘Adan’ on end label Stamped in end ‘WMR 200 E’ or ‘WMR 200 M’ or ‘WMR 100 E’

2 bolt fixing

Either ‘Geolink’ or ‘Comer industries’ on end label ‘GFS 200’ and ‘code 7.872200002’ printed on label or ‘GFS 100’ and ‘code 7.872100002’ printed on label Stamped in end 5 digit serial number eg ‘01006’

2 bolt fixing

‘M & S Hydraulic’ on end label ‘EPM’ printed on label Stamped in end ‘200 CO’ or ‘100 CO’

M&S Hydraulic 100cc (HYD5201) or 200cc MP (HYD5207) After August 2008 a change was made to M & S MP 100cc and 200cc motors as shown below. These can be identified due to them having a 2 bolt mounting flange.

Seal Kit for M & S MP motors is HYD4885 SAM Hydraulik 100cc (HYD5231) or 200cc BG HPS (HYD5232) A change has since been made to SAM Hydraulik motors. These can be identified due to them having an embossed ‘sh’ on the motor casting and a 25mm as opposed to 1 inch diameter output shaft.

Seal Kit for SAM Hydraulik BG HPS motors is HYD4891

‘M & S Hydraulic’ on end label ‘MP’ stamped in label ‘100 COD’ or ‘200 COD’ stamped in label

2 bolt fixing

25mm diameter output shaft

‘sh’ embossed on motor casting ‘SAM Hydraulik’ on end label

‘BG 100’ or ‘BG 200’ stamped in label

Seal Kit HYD4881 For Adan AWMR Motors No. Description Q’ty

1 Shaft seal 36 x 30 x 3.5 1

2 Shaft seal (PTFE) 36.5 x 28 x 3 1

3 Dirt Seal 35 x 27.5 x 3.5 1

4 Dished Washer 12.7 x 8.3 x 1 7

5 “O” Ring 48 x 43 x 2.7 1

6 “O” Ring 96 x 92 x 2 3

Seal Kit HYD4884 For Comer / Geolink GFSL Motors & M&S EPML Motors No. Description Q’ty Part Number

1 Dust Seal Ring 35 x 42 x 4 1 HYD4888

2 “O” Ring 69 x 3 1

3 Shaft Seal Ring 35 x 48 x 5.5 1 HYD4887

4 “O” Ring 5 x 1.5 2

5 “O” Ring 77.5 x 1.8 3

Seal Kit HYD4885 For Comer / Geolink GFS Motors And M&S EPM, MP & MPN Motors

No. Description Q’ty Part Number

1 Dust Seal Ring 35 x 28.5 x 4 1 HYD4890

2 Shaft Seal Ring 28.56 x 42 x 5.5 1 HYD4889

3 “O” Ring 48 x 2 1

4 “O” Ring 5 x 1.5 2

5 “O” Ring 77.5 x 1.8 3

Seal Kit HYD4891 For SAM Hydraulik BG HPS Motors No. Description Q’ty

1 Seal Ring 35 x 28 x 2.5 1

2 Seal Ring 35 x 28 x 5.0 1

3 Washer 12.5 x 8.3 x 1.2 7

4 Washer 18.8 x 13.5 x 1.4 1

5 “O” Ring 76.2 x 72.75 x 1.78 3