timerbar display assignment - duke manufacturing company
TRANSCRIPT
2 x 2 2 x 3 2 x 4 3 x 4 4 x 2
IMPORTANT INFORMATION, READ BEFORE INSTALLING
TIMER BAR DISPLAY ASSIGNMENT
PN 529008REV B 10/30/2017
This manual is Copyright © 2017 Duke Manufacturing Company. All rights reserved. Reproduction without written permission is prohibited. Duke is a registered
trademark of the Duke Manufacturing Company.
Duke Manufacturing Co.2305 N. Broadway
St. Louis, MO 63102Phone: 314-231-1130
Toll Free: 1-800-735-3853Fax: 314-231-5074www.dukemfg.com
4 x 4
2
Timer Display Assignments If at anytime you make an error, see Appendix A
1 23 4
Stand in front of the unit on POWER SWITCH SIDE.Turn power switch on.
Once the 4 arrows have been depressed, the displays should look
like this.
If the unit is 1-sided, it will now go into preheat mode.
If the unit is 2-sided, continue on to step 6.
Depress the 4 timer bar arrows in the numeric order indicated above.
Wait for timer bar to initialize (less than 15 seconds). Once initialized,
all displays will read “W1F.”
1
4 5
3
2
2x2
3
Move to the rear of the unit.
Once the 4 arrows have been depressed, the displays should look
like this.
The unit will now go into preheat mode.
Depress the 4 timer bar arrows in the numeric order indicated above.
The displays on the rear side should read “W1B.”
6
9 10
8
7
2 14 3
4
Timer Display Assignments If at anytime you make an error, see Appendix B
1 23 4
Stand in front of the unit on POWER SWITCH SIDE.Turn power switch on.
Once the 6 arrows have been depressed, the displays should look like this.
Wait for timer bar to initialize (less than 15 seconds).Once initialized, all displays will read “W1F.”
If the unit is 1-sided, it will now go into preheat mode.If the unit is 2-sided, continue on to step 4.
Depress the 6 timer bar arrows in the numeric order indicated above.
1
3
2
2 14 31 4 2 5 3 6
2x3
5
Move to the rear of the unit
Once the 6 arrows have been depressed, the displays should look like this.
The displays on the rear side should read “W1B.”
The unit will now go into preheat mode.
Depress the 6 timer bar arrows in the numeric order indicated above.
4
6
5
3 6 2 5 1 4
6
Timer Display Assignments If at anytime you make an error, see Appendix C
Stand in front of the unit on POWER SWITCH SIDE.Turn power switch on.
Once the 8 arrows have been depressed, the displays should look like this.
Wait for timer bar to initialize (less than 15 seconds).Once initialized, all displays will read “W1F.”
If the unit is 1-sided, it will now go into preheat mode.If the unit is 2-sided, continue on to step 4.
Depress the 8 timer bar arrows in the numeric order indicated above.
1
3
2
2x4
1 5 2 6 3 7 4 8
7
4 8 3 7 2 6 1 5
Move to the rear of the unit
Once the 8 arrows have been depressed, the displays should look like this.
The displays on the rear side should read “W1B.”
The unit will now go into preheat mode.
Depress the 8 timer bar arrows in the numeric order indicated above.
4
6
5
8
Timer Display Assignments If at anytime you make an error, see Appendix D
Stand in front of the unit on POWER SWITCH SIDE.Turn power switch on.
Once the 12 arrows have been depressed, the displays should look like this.
Wait for timer bar to initialize (less than 15 seconds).Once initialized, all displays will read “W1F.”
If the unit is 1-sided, it will now go into preheat mode.If the unit is 2-sided, continue on to step 4.
Depress the 12 timer bar arrows in the numeric order indicated above.
1
3
2
3x4
1 2 4
5 9 116 7 8
31 2 4
5 9 10 11 126 7 8
3
9
Move to the rear of the unit
Once the 12 arrows have been depressed, the displays should look like this.
The displays on the rear side should read “W1B.”
The unit will now go into preheat mode.
Depress the 12 timer bar arrows in the numeric order indicated above.
4
6
54 3 1
8 12 11 10 97 6 5
2
10
Timer Display Assignments If at anytime you make an error, see Appendix E
Stand in front of the unit on POWER SWITCH SIDE.Turn power switch on.
Once the 8 arrows have been depressed, the displays should look
like this.
If the unit is 1-sided, it will now go into preheat mode.
If the unit is 2-sided, continueon to step 6.
Depress the 8 timer bar arrows in the numeric order indicated to the left.
Wait for timer bar to initialize (less than 15 seconds). Once initialized,
all displays will read “W1F.”
1
4 5
3
2
4x2
1 5
3 7
2 6
4 8
11
Move to the rear of the unit.
Once the 8 arrows have been depressed, the displays should look
like this.
The unit will now go into preheat mode.
Depress the 8 timer bar arrows in the numeric order indicated to the left.
The displays on the rear side should read “W1B.”
6
9 10
8
7
2 6
4 8
1 5
3 7
12
Timer Display Assignments If at anytime you make an error, see Appendix F
Stand in front of the unit on POWER SWITCH SIDE.Turn power switch on.
Once the 16 arrows have been depressed, the displays should look like this.
If the unit is 1-sided, it will now go into preheat mode.
If the unit is 2-sided, continue on to step 4.
Depress the 16 timer bar arrows in the numeric order indicated to the Left.
1
3
2
4x4
1 5 2 6 3 7 4 8
9 13 10 14 11 15 12 16
Wait for timer bar to initialize (less than 15 seconds).Once initialized, all displays will read “W1F.”
13
Move to the rear of the unit.
Once the 16 arrows have been depressed, the displays should look like this.
The unit will now go into preheat mode.
Depress the 16 timer bar arrows in the numeric order indicated to the left.
The displays on the rear side should read “W1B.”
4
6
5 4 8 3 7 2 6 1 5
12 16 11 15 10 14 9 13
14
Turn the power button OFF and then ON. Wait for the display panels to initialize. Once initialized, it should look like the above display. If not, move on
to which will reset the assignments.
On the POWER SWITCH SIDE, press and HOLD any 2 arrows onDIFFERENT DISPLAYS for 10 seconds.
This will reset the timer bar assignment and allow you to start over.
1
2
2
Appendix AResetting Timer Assignments
2x2If at any time throughout the timer bar assignment process an arrow is pressed in the wrong order, you have the ability to reset and start over.
For more information contact: Duke Manufacturing Company
2305 N Broadway, St. Louis, MO 63102800.735.3853
15
Turn the power button OFF and then ON. Wait for the display panels to initialize. Once initialized, it should look like the above display. If not, move on
to which will reset the assignments.
On the POWER SWITCH SIDE, press and HOLD any 2 arrows onDIFFERENT DISPLAYS for 10 seconds.
This will reset the timer bar assignment and allow you to start over.
1
2
2
Appendix BResetting Timer Assignments
2x3If at any time throughout the timer bar assignment process an arrow is pressed in the wrong order, you have the ability to reset and start over.
For more information contact: Duke Manufacturing Company
2305 N Broadway, St. Louis, MO 63102800.735.3853
16
Turn the power button OFF and then ON. Wait for the display panels to initialize. Once initialized, it should look like the above display. If not, move on
to which will reset the assignments.
On the POWER SWITCH SIDE, press and HOLD any 2 arrows onDIFFERENT DISPLAYS for 10 seconds.
This will reset the timer bar assignment and allow you to start over.
1
2
2
Appendix CResetting Timer Assignments
2x4If at any time throughout the timer bar assignment process an arrow is pressed in the wrong order, you have the ability to reset and start over.
For more information contact: Duke Manufacturing Company
2305 N Broadway, St. Louis, MO 63102800.735.3853
17
Turn the power button OFF and then ON. Wait for the display panels to initialize. Once initialized, it should look like the above display. If not, move on
to which will reset the assignments.
On the POWER SWITCH SIDE, press and HOLD any 2 arrows onDIFFERENT DISPLAYS for 10 seconds.
This will reset the timer bar assignment and allow you to start over.
1
2
2
Appendix DResetting Timer Assignments
3x4If at any time throughout the timer bar assignment process an arrow is pressed in the wrong order, you have the ability to reset and start over.
For more information contact: Duke Manufacturing Company
2305 N Broadway, St. Louis, MO 63102800.735.3853
18
Turn the power button OFF and then ON. Wait for the display panels to initialize. Once initialized, it should look like the above display. If not, move on
to which will reset the assignments.
On the POWER SWITCH SIDE, press and HOLD any 2 arrows onDIFFERENT DISPLAYS for 10 seconds.
This will reset the timer bar assignment and allow you to start over.
1
2
2
Appendix EResetting Timer Assignments
4x2If at any time throughout the timer bar assignment process an arrow is pressed in the wrong order, you have the ability to reset and start over.
For more information contact: Duke Manufacturing Company
2305 N Broadway, St. Louis, MO 63102800.735.3853
19
Turn the power button OFF and then ON. Wait for the display panels to initialize. Once initialized, it should look like the above display. If not, move on
to which will reset the assignments.
On the POWER SWITCH SIDE, press and HOLD any 2 arrows onDIFFERENT DISPLAYS for 10 seconds.
This will reset the timer bar assignment and allow you to start over.
1
2
2
Appendix FResetting Timer Assignments
4x4If at any time throughout the timer bar assignment process an arrow is pressed in the wrong order, you have the ability to reset and start over.
For more information contact: Duke Manufacturing Company
2305 N Broadway, St. Louis, MO 63102800.735.3853
Duke Manufacturing Co.2305 N. Broadway
St. Louis, MO 63102Phone: 314-231-1130
Toll Free: 1-800-735-3853Fax: 314-231-5074
www.dukemfg.com