TEAMLINK NEXT GENERATION ROUTER

Features:

� TEAMLINK New Generation Router is developed with the High efficient Freescale Power PC based 32 Bit e300c3 Power Architecture processor core and QUICC Engine running at 333 MHz frequency.

� 32 Bit RISC controller for flexible support of communications peripherals � Latest Open source Linux Operating System � New Technology 1GB NAND Flash and 512Mbytes of DDR2 SDRAM � 3 LAN Interfaces with One 4 Port Built in switch PORT and Two Single 10/100 Ethernet

Interfaces Ports and 2 TDM Interfaces. � TDM interfaces can be configured One E1 port and One SHDSL line or One V35 Interface. � We can offer the Router as E1 Router / SHDSL Modem with Router / Metro Ethernet Router

which is having the 4 Port Built in switch on LAN side and One 10/100 Mbps Ethernet Port on WAN side.

� WAN Interfaces Options V35 / E1 / SHDSL and Ethernet � K.20 and K.21 Line Side Protection for the surges ( Current and Voltage ) � Dual AC and DC power supply input from the Same Socket.

SHDSL Line Specifications: (WAN)

� Line Type : 2 Wire Single Pair Operation � Line Code : TCPAM as per the ITU-T G.991.2 � Line Impedance : 135 Ohms � Connector : RJ45 � Transmit Power : 16.5 dBm � Line Protection : Provides Multistage line protection as per the ITU-T K.20 and K.21 � Transmit Level : Up to 14 dBm � Specification : ANSI T1.601 � Operating Range : 6Km on 0.5mm dia cable at 2.048Mbps speed,11Km at 64Kbps speed � DSL Data Rate can be configured from 64Kbps to 2048Kbps in steps of 64Kbps line Nx64Kbps � DSL Line UP and DOWN and PPP UP status monitoring through the Serial port

V35 INTERFACE SPECIFICATIONS (WAN):

� Connector Type : DB34 PIN Female Connector � Clocking : Recovered From V35 DCE Interface � Data Selection : Automatically Detects according to the Clocking. � Interface Type : DTE or DCE

E1 Interface (WAN)

� Number ports : 2E1 Ports � Bit Rate : 2.048Mbps � Line Coding : HDB3 or GFP � Framing : Supports Unframed ( Full E1 ) & Framed Mode (Fractional E1) of operations � Line Impedance : Balanced 120 Ohms � Interface Connectors : RJ45 or Two BNC Connectors (Optional) � Complies With : ITU G.703 and G.704.

� System Clock : Internal or loop back timing � Connector : RJ45 Connector

LAN Interface Specification (LAN):

� 4 10/100 Mbps Ethernet Ports with the Built in Layer2 switch. � Auto negotiation Enabled � Complied according to the IEEE802.3 � 10Base-T and 100Base TX Support � Mac Address learning and Filtering � Auto MDI-X Support

Clocking Supported:

� Recovered from the DSL line when the Router is configured in SHDSL Router or Recovered from E1

Interface when the Router is configured for the E1 Router. � Internal Local Oscillator Clock

Protocols Supports:

� ARP, RARP, ICMP � PPP, LCP, IPCP, IP � IPv4, TCP, UDP,TFTP, RIPv1, RIPv2,Static Route, ICMP � Dynamic Routing with the RIPv1, RIPv2, OSPFv2, OSPFv3, BGPV4 � IGMP � Network Address Translations ( NAT ) Support � DHCP Server and DHCP Client Support � Supports MLLN VMUX G703 Modem for Managed Leased Line Circuits � WAN protocol is PPP � Supports UDP broadcast and Uncast � Supports MPLS Core Router for Wide Area Connectivity

Diagnostics:

� Digital Loop, Remote Loop � Built In 511 Test Pattern Generation and Checking � PPP Status Monitoring � ICMP Request using the trace Route Menu � Diagnostic and Status Monitoring through the EOC channel without interfering the data transmission

Management:

Configuration and Status Monitoring is done using the Following Interfaces: � Console : Menu driven VT100 Terminal for Configuration and status monitoring � Telnet : Managed Ethernet Port or in –band management 10/100 Mbps Ethernet port � Minimum 6 Telnet Sessions Either from WAN or LAN Simultaneously without Configuring the

Management Interface � LAN and WAN statistics, Configuration of the speed can be from Telnet and also from the Console. � SNMPv1 and SNMPv2 Configurations and Notifications � Management through the SNMP and the Web-Interface

Software Upgradable:

� Through the Serial Port Using the X-Modem Protocol � Using the TFTP over Ethernet Port � High efficient Boot loader which is from open source u-boot repository � Up gradation of the NAND flash using the Boot loaders

LED Indications:

� PWR, DSL_LINK,MR, ERR,TST,PAT,ALM, ETH_LINK, ETH_SPD, PPP_LNK

Power Supply :

� 48V DC and 230V AC Dual power supply � Redundant Power supply is an ordering time Option. Redundancy of 5V DC is provided for Primary

Power supply so as to connect External 5V Power Adaptor in case Internal Power supply fails

Environment:

� Operating Temperature: -5 to +55°C � Operating Humidity:5% to 99 %

Casing:

� Rugged Metallic Aluminum Casing as per the Field Conditions

Application Diagram-I:

The following Application Diagram shows the TEAMLINK Serial Router and SHDSL Modem Router, E1 Router connecting with the MPLS Core Router.

Application Diagram-II:

The following Application Diagram shows TEAMLINK Serial Router and SHDSL Modem Router, E1 Router with the MPLS Core Router.

Application Diagram-III:

The following Application Diagram shows the TEAMLINK SHDSL Modem Routers for connecting Two stations with the Latest Routing Protocols

Application Diagram-IV:

The following Application Diagram shows the TEAMLINK E1 Router and the SHDSL Modem Router, for extending the ISP Services to the Remote Locations or Wide Area Connecting.

Application Diagram-V:

The following Application Diagram will shows the TEAMLINK Serial Router and the E1 Router, for ISP Providers or Wide Area Networks

Application Diagram-VI:

The following Application Diagram shows the TEAMLINK SHDSL Modem Router for the PRS and UTS Applications