t tptp-2 tpptp 2 ptp-2 tptp-2 tw 2 levels - …...advantages 1 ultra low noise because of it is...
TRANSCRIPT
PROFESSIONAL PARKING SOLUTION PROVIDER!
WE PLAN , DESIGN, MANUFACTURE AND INSTALL...
TPTP-2Two Post Tilting Parking Lift 2 levels
TPTP-2T
TPPTP 2
ROP
TPTP-2 wTTwo Post Tilting Parking Lift 2 levelsTP
APPARKING SOLUTION PROVIDER!OFESSIONALo Post TiltingPTP-2
ARKING SOLUTg Parking Lift
TION PROVIDER2 levels
R!
EW PLAN , DESIGN, MA ACTURE ANDFFACTURE AND INSANU ALL...TTALL...INS
Our Safety
Management System
is now 3rd Party
Certified! Safety CertifiedAU1275-SC
AS
4801:2001
TPTP-2Two Post Tilting Parking Lift 2 levels
Introduction
General Parts
10 Wheel stop lever
9 Balance shaft
7 Left footage
6 Limit switch
4 Cylinder
1 Platform
8 Safety lock
5 Pump shield(power unit)
3 Control arm
2 Column
1
3
4
5
6
7
8
9
11
12
h1
TPTP-2
h1(mm) 1850h2(mm) 1600
h3(mm) 3899
h4(mm) 2900
2
The two post tilting parking lift is a kind of valet parking. TPTP-2 is only used for sedans, and it is a subsidiary product of TPP-2 when you don’t have enough ceiling clearance. It moves vertically, the users have to clear the ground level to get the higher level car down.
It is hydraulic driven type that lifted by cylinders. Our standard lifting capacity is 2000kg, different �nishing and waterproof treatment are available at customer’s request.
10
11 Right footage
12 Control box
- Designed for low ceiling height- Galvanized platform with wave plate for better parking- 10 degree tilting platform- Dual hydraulic lifting cylinders direct drive- Individual hydraulic power pack and control panel- Self-standing and self-support structure- Can be moved or relocated- 2000kg capacity, suitable for sedan only- Electric key switch for security and safety- Automatic shut-off if operator releases the key switch- Both electrical and manual lock release for your choice- Maximum lifting height adjustable to for different - ceiling height- Mechanical anti-falling lock on top position- Hydraulic overloading protection
h2
h3
h4
wo Post TTTwo Post TTPTP-2
ilting Parking LT Lift 2 levels
In
It is h
level to get theverticallyhave enough ceiling clearance. It movessubsparkThe
oductionntr
hydraulic driven type that lifted by
higher level car down.l to get the, the users have to clear the ically
e enough ceiling clearance. It moveswhof TPP-2 oductprsidiary
king. TPTP-2 is only used for sedans, and it is a two post tilting parking lift is a kind of valet
cylinders. ted by
down.ound grar the
ce. It movesthen you don’
sedans, and it is a s a kind of valet
1h1
h4h44
- Ind- Du- 10
pa- Ga- De
at cu�nishingOur standarIt is h
h2
dividual hydraulic power pack and contral hydraulic lifting cylinders dir
ee tilting platformdegrrkinglvanized platform with wave plate for better signed for low ceiling height
equest.s rustomer’seatmtroof and waterprhing
d lifting capacity is 2000kg,standarhydraulic driven type that lifted by
ol panelk and contrect drivedir
plate for bettert
e available ment arent ferdif2000kg,
cylinders. ted by
TPTP-2
h3(mm)
h2(mm)h1(mm)
3899
16001850
h3h3
M- cei- Ma
cho- Bot- Aut- Ele- 200- Ca- Sel
Ind
h i l ti f lli l kling height
aximum lifting height adjustable to for difoiceth electrical and manual lock r
f if operator rtomatic shut-offf if operator rectric key switch for security and safety
, suitable for se00kg capacity,elocatedn be moved or r
f-standing and self-support structurdividual hydraulic power pack and contr
t iti
entferable to for dif
elease for yourk releases the key switchr
and safetyedan only
estructurol panelk and contr
General Parts
h4(mm)
s
2900- Hyd- Me
1
3
2 Column
ol arm3 Contr
Platform
otectiodraulic overloading prechanical anti-falling lock on top position
ontop position
11
5
6
7
8
9
10
43 Contr
Pump shield(power unit)
Safety lock
Cylinder
Limit switch
Left footage
Balance shaft
10 Wheel stop lever
11
11
12 ol box12 Contr
1 Right footage
Advantages
1 Ultra low noiseBecause of it is hydraulic cylinders driven type, no matter the car up or down, it makes low noise because of the buffering of the cylinders.
2 Safe and reliableThe limit switch on the post and the anti-drop device offer double safety for this equipment.
3 Fast and easy installationWith part of structure pre-installed in the factory, it is very easy on the installation work.
4 Simple operationPeople only need to turn the key switch on the control panel to operate the equipment.
5 Consumer product level �nishing A better powder coating as the standard surface treatment provide consumer product level �nishing.
6 Top quality processing
The TPTP-2 product is 100% cut by laser and more than 60% welded by robot.
Speci�cations
Surface treatment
Model
Vehicle size
Vehicle weight
Lifting height
Lock mode
Drive mode
Surface treatment
Control power
Lifting time
Lowering time
Voltage
Motor power
TPTP-2
5000mmX1850mmX1550mm
≤2000Kg
1600mm
Position lock
Hydraulic
Powder coating
24V
24S
24S
380V/220V
2.2kw
- For this kind of equipment, our standard surface treatment is powder coating for the main frame and galvanized plate for the platform.- Powder coating is applied as a free-�owing, dry powder. It is typically applied electrostatically and is then cured under heat to allow it to �ow and form a "skin".- It is usually used to create a hard �nish that is tougher than conventional paint.
1
2
3
4 5
6
7 Suitable for both home use and public use
Usually the equipment is mainly used for indoor and personal, but sometimes it
also be used for public use
Q
Drawing
Electric connection
TPTP-2
Parking VehicelsSingle vehicels weight(kg)
Type TpTp-2
Parking2
<2000kg5000mm1850mm1550mm
2.2kw
380V 50Hz3 phases or
Size ofcar
LengthWidthHeight
speed(seconds)Lifting
Electricity 220V 50Hz 1 phases
Pump motor<45
1600
2590
1308
2100
2585
6000
3100
3899
1848
TPTP-2
TPP-2
FPSP-4
FPP-2
BDP-3
PFPP-3
VRC
CTT
1)Before operation, con�rm there is no person or object stay in the parking equipment to avoid accident2)Turn the key to park or take the car.
3)Attentions when parking the car: Please put away the antenna before the car enters the parking equipment. The car can be parked or taken out only after the platform stop running. Parking the car in appropriate position according to the car length to avoid car damage. After parking the car, pull the hand brake and leave. Please check unlock hook, make sure it at security locking state then leave.
Maintenance should be according to the working frequency of the parking equipment.1)Daily maintenance and check: The user or operator should responses the daily maintenance and check. The platform and parking ground should be kept clean and clear; Clear the surface of the moving parts; If there is any abnormal noise, please inform the maintainer;2)Regular maintenance and check: Professional maintainer should do regular maintenance and check, and details as per the table below.
Car-parking: Turn the key clockwise, platform rises;Car-taking: Turn the key counterclockwise, platform falls down.The alert lamp glistens during running(to warn staff around ; After the car is in place, take out the key.
Attention during operation
- Only trained person can operate the equipment;
- Before operation, con�rm there is no person in equipment area;
- Prohibit anyone entering into the equipment area except the driver;
- When parking: ① Put away the antenna, and slowly drive onto the platform; ② Locating the car; ③ Flameout, and pull hand brake; ④Get down the car,
and close the car door.
- Connect professional maintainer or connect the manufacturer if there is any abnormal trouble. Never try it by yourself.
- Prohibit driving when drunk.
- Prohibit parking the car of wrong dimension and weight.
- Prohibit �re around the equipment.
Operation procedure
Maintenance
Check List of maintenance
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Check list
Running condition
Foundation of main column
Fixation of bolt
Check if the steel frame and platform deforms.
Lifting device
Hoisting arm of platform
If there is any leakage about cylinder
if there is any abnormal noise about transmission device
Pulley running condition
If there is deformation about pulley
If the location of the limit switch is right
Adjust the balance of platform
If the hydraulic oil in power unit is enough
If there is any abnormal noise about power unit
If the oil hose is worn
If brake steel cable is worn
If anti-drop hook runs normally
If wire insulation bush or pipe is worn
If each indicator light is normal
Trouble Shooting
Failure
No power
Lights arenot work
Mechanicalpart doesnot work
Platformcannot be
in place
Platformcannot stopwhen it isin place
Reason
Outage
Power switch trip
Key switch is on OFF
Power light,button lightand warning light are all
burned
Knob of control box fails
Limit switch fails
Limit switch displaces.
Platform is blocked
Limit switch displaces
Limit switch fails
Method
Switch on
Turn key switch to ON and powerlight will be on
Change the lights
Change the knob
Repair or change limit switch
Adjust the position of limit switch
Clear the block
Adjust the position of limit switch
Repair or change limit switch
1
2
3
o
The alert lamp glistens during runningurn the key counter-taking: TCar
urn the key clockwise, platform rises;-parking: TCarurn the key to park or take the carT)2
e operation, con�rm therBefor)1
Operation prp p e
to warn staf(ens during runningclockwise, platform falls down.key counter
e key clockwise, platform rises;.park or take the carr.
e is no person or object stay in the parking equipment to avoid accidentn, con�rm ther
cedur
ound ; After the car is in place, take out the keyf arstafffrm falls down.s;
or object stay in the parking equipment to avoid accident
n place, take out the key
quipment to avoid accident
2
1
The alert lamp glistens during running
Please check unlock hook, make surAfter parking the carParking the car in apprThe car can be parked or taken out only after the platform stop running.Please put away the antenna beforAttentions when parking the car:)3
e operation, con�rm therBefor
- Only trained person can operate the equipment;
Attention during operation
to warn staf(ens during running
e it at security locking state then leave.ock hook, make sur, pull the hand brake and leave.carr, pull the hand brake and leave.
diopriate position accorapprarked or taken out only after the platform stop running.
e the car enters the parking equipment.the antenna beforparking the car:
e is no person in equipment ar�rm ther
n operate the equipment;
ion
ound ; After the car is in place, take out the keyf arstafff
urity locking state then leave.eave.ng to the car length to avoid car damage.
the platform stop running.nters the parking equipment.
ea;ar
.n place, take out the key
car damage.3
Maintenance
ound the equipment.e arohibit �r- Pr
ohibit parking the car of wr- Pr
ohibit driving when drunk.- Pr
ofessional maintainer or connect the manufactur- Connect pr
and close the car doorr.
Put away the antenna, and slowly drive onto the platform; ①- When parking:
ohibit anyone entering into the equipment ar- Pr
e operation, con�rm ther- Befor
e equipment.
ong dimension and weight.r of wr
drunk.
maintainer or connect the manufactur
.
away the antenna, and slowly drive onto the platform;
ea except the driver;ng into the equipment ar
e is no person in equipment ar�rm ther
ouble. Never try it by yourself.e is any abnormal trer if therr
Locating the car; ②nto the platform;
he driver;
ea;ar
Never try it by yourself.
④Flameout, and pull hand brake; ③; ,Get down the carr, ④
Check List of m
.table belowRegular maintenance and check: Pr)2
e is any abnormal noise, please inform the maintainer;If therClear the surface of the moving parts;The platform and parking grDaily maintenance and check: The user or operator should r)1
Maintenance should be accor
maintenance
ofessional maintainer should do rance and check: Prnormal noise, please inform the maintainer;
e of the moving parts;ound should be kept clean and clear;d parking gr
ce and check: The user or operator should rding to the working frd be accor
oubl
egular maintenance and check, and details as per the maintainer should do rhe maintainer;
ept clean and clear;esponses the daily maintenance and check.erator should r
equency of the parking equipment.fr
rT e Shooting
maintenance and check, and details as per the
daily maintenance and check.uipment.
g
d details as per the
Check list
Hoisting arm of platform
Lifting device
Check if the steel frame and platform deforms.
Fixation of bolt
Foundation of main column
Running condition
.
6
5
4
3
2
1
No
of platform
eel frame and platform deforms.
t
f main column
ition
keLights ar
No powe
eFailur
C
powurn kT
lld i li hPower light,button light
Key switch is on OFF
Power switch trip
Outage
Reason
e
r
Ch h li h
werlight will be on key switch to ON and
Switch on
Method
e is any abnormal noise about power unitIf ther
If the hydraulic oil in power unit is enough
Adjust the balance of platform
If the location of the limit switch is right
e is deformation about pulleyIf ther
Pulley running condition
e is any abnormal noise about transmission deviceif ther
e is any leakage about cylinderIf ther
14
13
12
11
10
9
8
7
abnormal noise about power unit
c oil in power unit is enough
ance of platform
of the limit switch is right
ormation about pulley
condition
abnormal noise about transmission device
eakage about cylinder
in placecannot bePlatform
not workpart does
Mechanica
not work
t
on device
Adjust
Repair
C
C
Platform is blocked
Limit switch displaces.
Limit switch fails
ol box failsKnob of contr
burnede alland warning light ar
e
sal
Clear the block
switcht the position of limit
or change limit switch
Change the knob
Change the lights
If each indicator light is normal
e insulation bush or pipe is wornIf wir
op hook runs normallyIf anti-dr
If brake steel cable is worn
If the oil hose is worn
e is any abnormal noise about power unitIf ther
19
18
17
16
15
14
or light is normal
on bush or pipe is worn
ok runs normally
cable is worn
is worn
abnormal noise about power unit
in placewhen it is
cannot stoPlatform
t
Repair
Adjust
Limit switch fails
Limit switch displacesop
or change limit switch
switcht the position of limit
Q&A
1. How many cars could be parked for each set? 2 cars. One is on the ground and another is on the second �oor.2. Is TPTP-2 used indoor or outdoor? Both of them are available. The �nishing is powder coating and plate cover is galvanized, with rust-proof and rain-proof. When used indoor, you need consider the ceiling height.3. How much is the minimum ceiling height to use TPTP-2? 3100mm is the best height for 2 sedans with 1550mm high. Minimum 2900mm available height is acceptable to �t for TPTP-2.4. Is the operation easy? Yes. Keep holding the key switch to operate the equipment, which will stop at once if your hand releases.5. If the power is off, can I use the equipment normally? if the electricity failure happens often, we suggest you have a back-up generator, which can make sure the operation if no electricity. 6. What's the supply voltage? Standard voltage is 220v, 50/60Hz, 1Phase. Other voltages could be customized according to clients' request.7. How to maintain this equipment? how often it need the maintenance work? We can offer you the detailed maintenance guide, and actually the maintenance of this equipment is very simple, for example, keep the round environment tidy and clean, check whether the cylinder is leak oil, the bolt is loose or the steel cable is worn
Reference pictures
Australia Wide Sales and Service
Our website: www.materialshandling.com.au Phone us: 1300 25 84 07 Fax us: 1800 68 68 96 Email us: [email protected]